Lab - Using Wireshark to Examine Ethernet Frames

Mininet Topology

Objectives
Part 1: Examine the Header Fields in an Ethernet II Frame
Part 2: Use Wireshark to Capture and Analyze Ethernet Frames

Background / Scenario
When upper layer protocols communicate with each other, data flows down the Open Systems
Interconnection (OSI) layers and is encapsulated into a Layer 2 frame. The frame composition is dependent
on the media access type. For example, if the upper layer protocols are TCP and IP and the media access is
Ethernet, then the Layer 2 frame encapsulation will be Ethernet II. This is typical for a LAN environment.
When learning about Layer 2 concepts, it is helpful to analyze frame header information. In the first part of
this lab, you will review the fields contained in an Ethernet II frame. In Part 2, you will use Wireshark to
capture and analyze Ethernet II frame header fields for local and remote traffic.

Required Resources
 CyberOps Workstation virtual machine

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Instructions

Part 1: Examine the Header Fields in an Ethernet II Frame

In Part 1, you will examine the header fields and content in an Ethernet II Frame provided to you. A Wireshark
capture will be used to examine the contents in those fields.

Step 1: Review the Ethernet II header field descriptions and lengths.

Destination Source Frame

Preamble Address Address Type Data FCS

8 Bytes 6 Bytes 6 Bytes 2 Bytes 46 – 1500 Bytes 4 Bytes

Step 2: Examine Ethernet frames in a Wireshark capture.

The Wireshark capture below shows the packets generated by a ping being issued from a PC host to its
default gateway. A filter has been applied to Wireshark to view the ARP and ICMP protocols only. The
session begins with an ARP query for the MAC address of the gateway router, followed by four ping requests
and replies.

Step 3: Examine the Ethernet II header contents of an ARP request.

The following table takes the first frame in the Wireshark capture and displays the data in the Ethernet II
header fields.

Field Value Description

Preamble Not shown in capture This field contains synchronizing bits, processed by the NIC
hardware.

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Field Value Description

Destination Address Broadcast Layer 2 addresses for the frame. Each address is 48 bits
(ff:ff:ff:ff:ff:ff) long, or 6 octets, expressed as 12 hexadecimal digits, 0-
9,A-F.
Source Address IntelCor_62:62:6d A common format is 12:34:56:78:9A:BC.
(f4:8c:50:62:62:6d) The first six hex numbers indicate the manufacturer of the
network interface card (NIC), the last six hex numbers are
the serial number of the NIC.
The destination address may be a broadcast, which contains
all ones, or a unicast. The source address is always unicast.
Frame Type 0x0806 For Ethernet II frames, this field contains a hexadecimal
value that is used to indicate the type of upper-layer protocol
in the data field. There are numerous upper-layer protocols
supported by Ethernet II. Two common frame types are:
Value Description
0x0800 IPv4 Protocol
0x0806 Address resolution protocol (ARP)

Data ARP Contains the encapsulated upper-level protocol. The data

field is between 46 – 1,500 bytes.
FCS Not shown in capture Frame Check Sequence, used by the NIC to identify errors
during transmission. The value is computed by the sending
machine, encompassing frame addresses, type, and data
field. It is verified by the receiver.

What is significant about the contents of the destination address field?

The significance of the contents of the destination address field is that it is a broadcast.

Why does the PC send out a broadcast ARP prior to sending the first ping request?

It sends out a broadcast ARP prior because the PC is attempting to capture the MAC address for the
destination address so that it is able to build a frame header.

What is the MAC address of the source in the first frame?

00:1a:73:ea:63:8c

What is the Vendor ID (OUI) of the Source’s NIC?

GemtekTE_EA:63:8c

What portion of the MAC address is the OUI?

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames
The first 24 bits

What is the Source’s NIC serial number?

00:1a:73

Part 2: Use Wireshark to Capture and Analyze Ethernet Frames

In Part 2, you will use Wireshark to capture local and remote Ethernet frames. You will then examine the
information that is contained in the frame header fields.

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Step 1: Examine the network configuration of H3.

a. Start and log into your CyberOps Workstation VM using the following credentials:
Username: analyst Password: cyberops
b. Open a terminal emulator to start mininet and enter the following command at the prompt.
When prompted, enter cyberops as the password.
[analyst@secOps ~]$ sudo ./lab.support.files/scripts/cyberops_topo.py
[sudo] password for analyst:
c. At the mininet prompt, start terminal windows on host H3.

*** Starting CLI:

mininet> xterm H3
d. At the prompt on Node: h3, enter ip address to verify the IPv4 address and record the MAC address.

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Host-interface IP Address MAC Address

H3-eth0

e. At the prompt on Node: H3, enter netstat -r to display the default gateway information.

[root@secOps ~]# netstat -r

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
default 10.0.0.1 0.0.0.0 UG 0 0 0 H3-eth0
10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 H3-eth0

What is the IP address of the default gateway for the host H3? 10.0.0.1

Step 2: Clear the ARP cache on H3 and start capturing traffic on H3-eth0.
a. In the terminal window for Node: H3, enter arp -n to display the content of the ARP cache.
[root@secOps analyst]# arp -n
b. If there is any existing ARP information in the cache, clear it by enter the following command: arp -d
IP- address. Repeat until all the cached information has been cleared.

[root@secOps analyst]# arp -n

Address HWtype HWaddress Flags Mask Iface
10.0.0.11 ether 5a:d0:1d:01:9f:be C H3-eth0

[root@secOps analyst]# arp -d 10.0.0.11

Address HWtype HWaddress Flags Mask Iface
10.0.0.11 (incomplete) C H3-eth0

c. In the terminal window for Node: H3, open Wireshark and start a packet capture for H3-eth0 interface.

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

[root@secOps analyst]# wireshark-gtk &

Step 3: Ping H1 from H3.

a. From the terminal on H3, ping the default gateway and stop after send 5 echo request packets.

[root@secOps analyst]# ping -c 5 10.0.0.1

b. After the ping is completed, stop the Wireshark capture.
 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 8 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Step 4: Filter Wireshark to display only ICMP traffic.

Apply the icmp filter to the captured traffic so only ICMP traffic is shown in the results.

Step 5: Examine the first Echo (ping) request in Wireshark.

The Wireshark main window is divided into three sections: the Packet List pane (top), the Packet Details
pane (middle), and the Packet Bytes pane (bottom). If you selected the correct interface for packet capturing
in Step 3, Wireshark should display the ICMP information in the Packet List pane of Wireshark, similar to the
following example.

a. In the Packet List pane (top section), click the first frame listed. You should see Echo (ping) request
 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 9 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames
under the Info heading. This should highlight the line blue.
b. Examine the first line in the Packet Details pane (middle section). This line displays the length of
the frame; 98 bytes in this example.
c. The second line in the Packet Details pane shows that it is an Ethernet II frame. The source
and destination MAC addresses are also displayed.

What is the MAC address of the PC’s NIC

d8:5e:d3:03:3c:c3

What is the default gateway’s MAC address?

10:0c:6b:f2:93:fe

d. You can click the arrow at the beginning of the second line to obtain more information about the
Ethernet II frame.

What type of frame is displayed?

0x0800 or an IPv4 frame type.

e. The last two lines displayed in the middle section provide information about the data field of the
frame. Notice that the data contains the source and destination IPv4 address information.

What is the source IP address? 10.0.0.25

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 10 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

What is the destination IP address? 10.0.0.1

f. You can click any line in the middle section to highlight that part of the frame (hex and ASCII) in the
Packet Bytes pane (bottom section). Click the Internet Control Message Protocol line in the
middle section and examine what is highlighted in the Packet Bytes pane.

g. Click the next frame in the top section and examine an Echo reply frame. Notice that the source and
destination MAC addresses have reversed, because this frame was sent from the default gateway
router as a reply to the first ping.

What device and MAC address is displayed as the destination address? My PC NIC
 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 11 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Step 6: Start a new capture in Wireshark.

a. Click the Start Capture icon to start a new Wireshark capture. You will receive a popup window asking
if you would like to save the previous captured packets to a file before starting a new capture. Click
Continue without Saving.
b. In the terminal window of Node: H3, send 5 echo request packets to 172.16.0.40.
c. Stop capturing packets when the pings are completed.

Step 7: Examine the new data in the packet list pane of Wireshark.
In the first echo (ping) request frame, what are the source and destination MAC addresses?
Source:
d8:5e:d3:03:3c:c3

Destination:

10:0c:6b:f2:93:fe

What are the source and destination IP addresses contained in the data field of the frame?
Source:
10.0.0.25

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 12 of www.netacad.com
13
Lab - Using Wireshark to Examine Ethernet Frames

Destination:

104.92.231.139

Compare these addresses to the addresses you received in Step 5. The only address that changed is the
destination IP address.

Why has the destination IP address changed, while the destination MAC address remained the same?

Layer 2 frames never leave the LAN. When a ping is issued to a remote host, the source will use the default
gateway MAC address for the frame destination. The default gateway receives the packet, strips the Layer 2
frame information from the packet and then creates a new frame header with the MAC address of the next hop.
This process continues from router to router until the packet reaches its destination IP address.

Reflection
Wireshark does not display the preamble field of a frame header. What does the preamble contain?
The preamble field contains seven octets of alternating 1010 sequences, and one octet that signals the
beginning of the frame, 10101011.

 2017 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 13 of www.netacad.com
13