Introduction to FET’s

Current Controlled vs Voltage Controlled Devices

2
 Types of FET’s

• JFET – Junction Field Effect Transistor

• MOSFET – Metal Oxide Semiconductor Field Effect
Transistor
– D-MOSFET - Depletion Mode MOSFET
– E- MOSFET - Enhancement Mode MOSFET

3
 Transfer Characteristics
The input-output transfer characteristic of the JFET is not as straight
forward as it is for the BJT

In a BJT,  (hFE) defined the relationship between IB (input current) and IC

(output current).

In a JFET, the relationship (Shockley’s Equation) between VGS (input

voltage) and ID (output current) is used to define the transfer characteristics,
and a little more complicated (and not linear):
2
 VGS 
ID = IDSS  1 - 
 VP 
As a result, FET’s are often referred to a square law devices

4
 JFET Construction
There are two types of JFET’s: n-channel and p-channel.
The n-channel is more widely used.

There are three terminals: Drain (D) and Source (S) are connected to n-channel
5
Gate (G) is connected to the p-type material
 JFET Operating Characteristics

There are three basic operating conditions for a JFET:

JFET’s operate in the depletion mode only
A. VGS = 0, VDS is a minimum value depending on IDSS and the
drain and source resistance
B. VGS < 0, VDS at some positive value and
C. Device is operating as a Voltage-Controlled Resistor

For an n channel JFET, VGS may never be positive*

For an p channel JFET, VGS may never be negative*

6
 N-Channel JFET Operation

The nonconductive depletion region becomes thicker with increased reverse bias.
(Note: The two gate regions of each FET are connected to each other.)

7
N-Channel JFET Symbol

8
 Saturation

At the pinch-off point:

• any further increase in VGS does not produce any increase in ID. VGS at
pinch-off is denoted as Vp.
• ID is at saturation or maximum. It is referred to as IDSS.
• The ohmic value of the channel is at maximum. 9
 ID  IDSS

As VGS becomes more negative:

• the JFET will pinch-off at a lower voltage (Vp).
• ID decreases (ID < IDSS) even though VDS is increased.
• Eventually ID will reach 0A. VGS at this point is called Vp or VGS(off).
• Also note that at high levels of VDS the JFET reaches a breakdown situation.
ID will increases uncontrollably if VDS > VDSmax.
10
 FET as a Voltage-Controlled Resistor

The region to the left of the pinch-off point is called the ohmic
region. ro
rd =
The JFET can be used as a variable resistor, where VGS controls  VGS 
2

the drain-source resistance (rd). As VGS becomes more negative,  1 - 

 VP 
the resistance (rd) increases.

11
 Transfer (Transconductance) Curve

From this graph it is easy to determine the value of ID for a given value of VGS
It is also possible to determine IDSS and VP by looking at the knee where VGS is 0

12
 Plotting the Transconductance Curve
Using IDSS and VP (or VGS(off)) values found in a specification sheet, the Family of Curves
can be plotted by making a table of data using the following 3 steps:

Step 1:
2
 VGS 
Solve ID = IDSS  1 -  for VGS = 0V
 VP 

Step 2
2
 VGS 
Solve ID = IDSS  1 -  for VGS = VP ( aka VGS(off) )
 VP 

Step 3:
2
 VGS 
Solve ID = IDSS  1 -  for 0V VGS  VP in 1V increments for VGS
 VP 

13
 p-Channel JFET’s

p-Channel JFET operates in a similar manner as the n-channel JFET except the voltage
polarities and current directions are reversed

14
 P-Channel JFET Characteristics

As VGS increases more positively

• the depletion zone increases
• ID decreases (ID < IDSS)
• eventually ID = 0A
Also note that at high levels of VDS the JFET reaches a breakdown situation. ID increases
uncontrollably if VDS > VDSmax.
15
 MOSFET’s

Mettle Oxide Semiconductor FET

IGFET – Insulated Gate FET
 MOSFETs

MOSFETs have characteristics similar to JFETs and additional

characteristics that make then very useful

There are 2 types of MOSFET’s:

• Depletion type MOSFET (D-MOSFET)
• Operates in Depletion mode the same way as a JFET when VGS  0
• Operates in Enhancement mode like E-MOSFET when VGS > 0
• Enhancement type MOSFET (E-MOSFET)
• Operates in Enhancement mode
• IDSS = 0 until VGS > VT (threshold voltage)

17
 MOSFET Handling

MOSFETs are very static sensitive. Because of the very thin SiO2 layer between
the external terminals and the layers of the device, any small electrical discharge
can stablish an unwanted conduction.

Protection:
• Always transport in a static sensitive bag
• Always wear a static strap when handling MOSFETS
• Apply voltage limiting devices between the Gate and Source, such as back-to-
back Zeners to limit any transient voltage

18
D-MOSFET Symbols

19
 Depletion Mode MOSFET Construction

The Drain (D) and Source (S) leads connect to the to n-doped regions
These N-doped regions are connected via an n-channel
This n-channel is connected to the Gate (G) via a thin insulating layer of SiO2
The n-doped material lies on a p-doped substrate that may have an additional terminal
connection called SS
20
 Basic Operation
A D-MOSFET may be biased to operate in two modes:
the Depletion mode or the Enhancement mode

21
 D-MOSFET Depletion Mode Operation

The transfer characteristics are similar to the JFET

In Depletion Mode operation:
When VGS = 0V, ID = IDSS
When VGS < 0V, ID < IDSS
When VGS > 0V, ID > IDSS  VGS 
2

The formula used to plot the Transfer Curve, is: ID = IDSS  1 - 

 VP 
22
 D-MOSFET Enhancement Mode Operation

Enhancement Mode operation

In this mode, the transistor operates with VGS > 0V, and ID increases above IDSS
Shockley’s equation, the formula used to plot the Transfer Curve, still applies but VGS is
positive: 2
 VGS 
ID = IDSS  1 - 
 VP 
23
 p-Channel Depletion Mode MOSFET

The p-channel Depletion mode MOSFET is similar to the n-channel except that the
voltage polarities and current directions are reversed

24
Enhancement Type
MOSFET’s
n-Channel E-MOSFET showing channel length L and
channel width W

26
 Enhancement Type MOSFET Construction

The Drain (D) and Source (S) connect to the to n-doped regions
These n-doped regions are not connected via an n-channel without an external voltage
The Gate (G) connects to the p-doped substrate via a thin insulating layer of SiO2
The n-doped material lies on a p-doped substrate that may have an additional terminal
connection called SS
27
E-MOSFET Symbols

28
 Basic Operation
The Enhancement mode MOSFET only operates in the enhancement mode.

VGS is always positive

IDSS = 0 when VGS < VT
As VGS increases above VT, ID increases
If VGS is kept constant and VDS is increased, then ID saturates (IDSS)
The saturation level, VDSsat is reached.

29
 Transfer Curve

ID(on)
k=
To determine ID given VGS: ID = k (VGS - VT)2 (VGS(ON) - VT)2
where VT = threshold voltage or voltage at which the MOSFET turns on.
k = constant found in the specification sheet
The PSpice determination of k is based on the geometry of the device:
 W  KP 
k =   where KP = μNCOX
 L  2 

30
 p-Channel Enhancement Mode MOSFETs
The p-channel Enhancement mode MOSFET is similar to the n-channel except that the
voltage polarities and current directions are reversed.

31
 Summary Table

JFET D-MOSFET E-MOSFET

32