This document provides installation instructions for installing an AM/FM CD tuner and pocket attachment kit in a vehicle. It includes a parts list and diagrams showing how to install the pocket and attach the audio unit. The instructions are: 1) Remove the existing audio panel. 2) Install the pocket using screws. 3) Shape the pocket. 4) Attach the audio unit to the pocket using brackets and screws. 5) Connect wiring and install the assembly in the dash. 6) Secure with screws and test operation.
This document provides installation instructions for installing an AM/FM CD tuner and pocket attachment kit in a vehicle. It includes a parts list and diagrams showing how to install the pocket and attach the audio unit. The instructions are: 1) Remove the existing audio panel. 2) Install the pocket using screws. 3) Shape the pocket. 4) Attach the audio unit to the pocket using brackets and screws. 5) Connect wiring and install the assembly in the dash. 6) Secure with screws and test operation.
This document provides installation instructions for installing an AM/FM CD tuner and pocket attachment kit in a vehicle. It includes a parts list and diagrams showing how to install the pocket and attach the audio unit. The instructions are: 1) Remove the existing audio panel. 2) Install the pocket using screws. 3) Shape the pocket. 4) Attach the audio unit to the pocket using brackets and screws. 5) Connect wiring and install the assembly in the dash. 6) Secure with screws and test operation.
This document provides installation instructions for installing an AM/FM CD tuner and pocket attachment kit in a vehicle. It includes a parts list and diagrams showing how to install the pocket and attach the audio unit. The instructions are: 1) Remove the existing audio panel. 2) Install the pocket using screws. 3) Shape the pocket. 4) Attach the audio unit to the pocket using brackets and screws. 5) Connect wiring and install the assembly in the dash. 6) Secure with screws and test operation.
Downloaded from www.Manualslib.com manuals search engine
INSTALLATION 3. Push the front of the pocket from above and below and hold for one minute to fix the shape. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, PUSHDOWN equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Wrap a shop towel around the top of a flat-tip
screwdriver and insert it into the grooves of the POCKET audio panel. Pull the audio panel out toward you to release the five clips and remove the audio panel. Take care not to damage the clips and the audio PUSHUP panel. Disconnect the antenna lead and the 20-pin 2008060K connector from the rear of the cover.
CLIPS (5) VEHICLE 20-PIN 4. Position the audio unit on the pocket and install CONNECTOR the two brackets with the four 5 x 8 mm washer- bolts and two 4 x 12 mm self-tapping screws.
5 x 8 mm 5 x 8 mm BRACKET WASHER- WASHER- "R" SCREW SCREW Use the AUDIO BRACKET COVER lower UNIT "L" hole
ANTENNA AUDIO LEAD 4 x 12 mm PANEL SELF- TAPPING SCREW GROOVES IN AUDIO PANEL POCKET 2828202K 4 x 12 mm SELF- FLAT-TIP TAPPING SCREWDRIVER SCREW
2. Remove and discard the cover from the audio Use the upper hole. panel (four tabs). Tighten with a screw COVER while pushing the 2625021K (Not reused.) Insert the front of the pocket in boss on the upward direction. RETAINING pocket with TAB this hole.
Downloaded from www.Manualslib.com manuals search engine
Installing the Audio Unit and Pocket Assembly 5. While holding the audio unit close to the center panel opening, plug the vehicle 20-pin connector and antenna lead into the back of the audio unit.
ANTENNA LEAD
VEHICLE 20-PIN CONNECTOR
AUDIO UNIT
4 x 16 mm SELF-TAPPING SCREWS 2828210K
6. Slide the audio unit and pocket assembly into the
center panel opening and install the four 4 x 16 mm self-tapping screws. 7. Turn the ignition key on, and enter the radio anti-theft code. 8. Check the operation of the audio unit as described in the Owner’s Manual supplied. 9. Set the radio clock. 10. Reinstall all removed parts. 11. Put the AM/FM CD Tuner Owner’s Manual in the glove box.
