Manual Gp370 Mm21b Eng

1234567890123456789012345678901212345678901234567890123456789012123456789012345
1234567890123456789012345678901212345678901234567890123456789012123456789012345
1234567890123456789012345678901212345678901234567890123456789012123456789012345
1234567890123456789012345678901212345678901234567890123456789012123456789012345
Preface 1234567890123456789012345678901212345678901234567890123456789012123456789012345
Thank you for purchasing Digital’s Pro-face GP-370 Series of Graphic Control Panels (hereafter referred to
as the GP unit).
This GP unit, with its higher user functions and better overall performance, has been upgraded from the GP-
250 Series.
Please read this manual carefully as it explains, step by step, how to use the GP functions correctly.
In its examples, this manual uses the Mitsubishi MELSEC-AnA Series of PLC's wherever possible, con-
nected in a one-to-one relationship with the GP.
GP-370 Series refers to the following GP model numbers:

GP-370 Series.........GP370-LG11-24V, GP370-SC11-24V(Standard item)
GP370-LG41-24VP, GP370-SC41-24VP(CE marked item/c-UL maked item)
<Note>
1) It is forbidden to copy the contents of this manual, in whole or in part, except for the user's
personal use, without expressed permission from Digital Electronics Corporation of Japan
2) The information provided in this manual is subject to change without notice.
3) This manual has been written with care and attention to detail; however, should you find any
errors or omissions, please contact Digital Electronics and inform them of your findings.
4) Please be aware that we are not responsible for any damages resulting from the use of our
products, regardless of article 3 above.
5) Specifications set out in this manual are for overseas products only, and, as a result, some
differences exist between the specs given here and Japanese ones.
The "P" models are products jointly developed with Pro-face HMI B.V. in Europe. The front
sheet designs for these models differ from the standard or c-UL recognized models.
Company/Manufacturer names used in this manual are the registered trademarks of their
respective companies.
© Copyright March 1996, Digital Electronics Corporation
GP-370 Series User's Manual i

Table of Contents
Preface
Caution ............................................................................................................................................................. v
UL/c-UL(CSA)Approval ............................................................................................................................... vii
Package Contents ......................................................................................................................................... viii
Symbols ........................................................................................................................................................... ix
Chapter 1—Introduction
1.1 Before Operating GP .............................................................................................................................. 1-1
1.2 System Structure .................................................................................................................................... 1-2
1.3 Optional Equipment ................................................................................................................................. 1-5
Chapter 2—Specifications
2.1 General Specifications ............................................................................................................................ 2-1
1. Electrical Specifications ................................................................................................................................... 2-1
2. Environmental Specifications .......................................................................................................................... 2-2
3. Structural Specifications ................................................................................................................................. 2-2
2.2 Function and Performance ..................................................................................................................... 2-3
1. Display Functions ........................................................................................................................................... 2-3
2. Screen Memory ................................................................................................................................................ 2-4
3. Touch Panel / Clock Accuracy ........................................................................................................................ 2-4
4. External Interface ............................................................................................................................................. 2-4
2.3 Interface Specifications .......................................................................................................................... 2-5
1. Serial Interface ................................................................................................................................................. 2-5
2.4 Names and Functions of GP Parts ......................................................................................................... 2-6
2.5 Graphic Panel Dimensions ...................................................................................................................... 2-7
1. GP-370 External Dimensions ............................................................................................................................ 2-7
2. Installation Fasteners ...................................................................................................................................... 2-8
3. GP Installation Dimensions ............................................................................................................................. 2-9
Chapter 3—Installation and Wiring

3.1 Installation ............................................................................................................................................... 3-1
1. Installation ....................................................................................................................................................... 3-1
3.2 Wiring ...................................................................................................................................................... 3-5
1. Power Cable Connection ................................................................................................................................. 3-5
2. Precaution: Grounding .................................................................................................................................... 3-6
3. Precaution: Input/Output Signal Lines ........................................................................................................... 3-6
3.3 Tool Connector ....................................................................................................................................... 3-7
ii GP-370 Series User's Manual

Chapter 4—Off-line Mode
4.1 Entering Off-line Mode ........................................................................................................................... 4-1
1. When Turning the Unit On .............................................................................................................................. 4-1
2. Enter From Force Reset .................................................................................................................................... 4-2
4.2 Main Menu .............................................................................................................................................. 4-3
4.3 INITIALIZE—Standard Operations ...................................................................................................... 4-4
4.4 SELF-DIAGNOSIS—Standard Operations ........................................................................................... 4-5
4.5 Transfer Screen Data ............................................................................................................................. 4-7
Chapter 5—Initialize
5.1 Initialize Screen ....................................................................................................................................... 5-1
5.2 Initialize Items ......................................................................................................................................... 5-2
5.3 SYSTEM ENVIRONMENT SETUP ................................................................................................... 5-3
1. SYSTEM SETUP .............................................................................................................................................. 5-3
2. SYSTEM AREA SETUP .................................................................................................................................. 5-4
3. GLOBAL WINDOW SETUP ............................................................................................................................ 5-5
4. CHARACTER STRING DATA SETUP ............................................................................................................ 5-6
5.4 SET UP I/O ............................................................................................................................................ 5-9
1. SET UP SIO ...................................................................................................................................................... 5-9
2. SET UP I/O .................................................................................................................................................... 5-10
3. COMMUNICATION SETUP ......................................................................................................................... 5-12
5.5 PLC SETUP ......................................................................................................................................... 5-13
1. SET UP OPERATION SURROUNDINGS (1:1) ............................................................................................... 5-13
2. SET UP OPERATION SURROUNDINGS (n:1) .............................................................................................. 5-14
3. STATION SETUP (n:1) .................................................................................................................................. 5-15
4. CUSTOMIZE SETUP ..................................................................................................................................... 5-17
5.6 INITIALIZE MEMORY ...................................................................................................................... 5-19
5.7 SET UP TIME ...................................................................................................................................... 5-19
5.8 SET UP SCREEN ................................................................................................................................ 5-20
5.9 FONT SETTING .................................................................................................................................. 5-21
Chapter 6—RUN and Errors

6.1 RUN ........................................................................................................................................................ 6-1
1. Powering Up .................................................................................................................................................... 6-1
2. Off-line Mode .................................................................................................................................................. 6-1
6.2 Troubleshooting ....................................................................................................................................... 6-2
1. Troubles ........................................................................................................................................................... 6-2
2. No Display ....................................................................................................................................................... 6-4
3. Would Not Communicate ................................................................................................................................. 6-7
4. The Touch Panel Does Not Work .................................................................................................................... 6-9
GP-370 Series User's Manual iii

6.3 SELF-DIAGNOSIS .............................................................................................................................. 6-10
1. SELF-DIAGNOSIS Item List .......................................................................................................................... 6-10
2. SELF-DIAGNOSIS—Details Of Each Item .................................................................................................... 6-11
6.4 Error Message ...................................................................................................................................... 6-14
1. Error Message List ........................................................................................................................................ 6-14
2. Error Messages—Details ............................................................................................................................... 6-15
Chapter 7—Maintenance
7.1 Regular Cleaning .................................................................................................................................... 7-1
7.2 Periodic Check-Up ................................................................................................................................. 7-2
7.3 Changing the Backlight ........................................................................................................................... 7-3
Index
iv GP-370 Series User's Manual

Caution
For safe and correct use of this unit, follow these guidelines.
• Because of the ever present danger of electric shocks, make sure the Power
Cable is not plugged in when connecting it up to the GP.
• Whenever changing the Backlight, to prevent electric shocks or burns, be
sure to turn off the GP power and use protective gloves.
• Because the GP is loaded with high voltage parts, electric shocks can occur
when disassembling the unit. Do not disassemble the GP.
• Do not use power beyond the specified voltage range. If you do, it may
cause a fire or an electric shock.
• Do not reconstruct the GP unit. It may cause a fire or an electric shock.
• Do not use the GP in an environment with flammable gas in the surround-
ing atmosphere. It may cause explosion.
• GP uses a lithium battery for backing up its internal clock data. If the
battery is incorrectly replaced, the battery may explode. To avoid the dan-
ger, please do not replace the battery yourself. When the battery needs a
replacement, please consult with your local GP distributor.
• Do not use touch panel keys in life-related or important disaster prevention
situations. Use separate hardware switches for such keys.
• Please design your system so that the machine will not malfunction by a
communication fault between the GP and its host controller. If not, there
could be a danger of injuring a person or damaging materials.
To Prevent From Damage:

• Do not hit the touch panel with hard or heavy objects, or press the touch
panel with too much force, for it may cause irreparable damage.
• If you place the GP in an environment outside the specified temperature
range, the GP will break down.
• Do not allow water, liquids, or metals—which can cause a GP breakdown
or electric shocks—inside the GP unit.
• Avoid reducing the GP ventilation, or storing and using the GP in an envi-
ronment that increases the GP temperature.
• Avoid using and storing the GP in direct sunlight and in dusty or dirty envi-
ronments.
GP-370 Series User's Manual v

• Because the GP is a precision instrument, do not store or use the GP where
powerful impacts and vibrations will disrupt the unit.
• Do not store or use the GP where chemicals and acids evaporate, or where
chemicals and acids are dispersed into the air. The GP may become in-
fected.
• Do not use paint thinner or organic solvents to clean the main unit or dis-
play.
• Because unforeseen circumstances may befall your GP unit, be sure to back
up your screen data.
• About GP's Display Panel
• The Display Panel contents and the Contrast Adjustment affect the
intensity of Contouring. (Contour—when some parts of the screen
are brighter than others, creating a wavelike pattern.)
• There are minute grid-points on the Display Panel surface.
• Shadows may appear at the top of the LCD extension.
• Sometimes the display field may look as if the display colors have
changed. This phenomenon is a common attribute of LCD's, and not
a defect in the system.
• Displaying a single image for long periods can cause an afterimage to
remain when changing to another screen.
set the unit to "Stand-by Mode", which turns the screen Off automati-
cally when there is no input (a single screen display with no opera-
tions) for a specified period of time.
To prevent this effect:
set the unit to "Stand-by Mode", which turns the screen Off auto-
matically when there is no input (a single screen display with no op-
erations) for a specified period of time;
do not display any single screen for a long period of time. Change
the screen display periodically.
vi GP-370 Series User's Manual

UL/c-UL(CSA) Approval
The GP370-LG41-24VP and GP370-SC41-24VPare UL/c-UL recognized products.
(UL file No. E182139)
■GP conforms as a component for the following standards:
・UL508
Industrial Control Equipment
・UL1604
Electrical Equipment for Use in ClassⅠ andⅡ,Division2,and ClassⅢ
Hazardous(Classified)Locations
・CAN/CSA-C22.2.Nos.142.and 213-M1987
Standard for Safety of infomation Technology Equipment, including Elsctrical Business
Equipment
GP370-LG31-24V (UL Registration Model: 2780051-1)

GP370-SC31-24V (UL Registration Model: 2780051-2)
• The GP should be installed in the front face of a metal panet.
• If the GP is installed so as to cool itself naturally, please mount it onto a vertical panel.
Also, ensure that GP unit is mounted at least 100mm away from adjacent structures and
other parts. If these conditions are not met, the heat gene rated by internal components
may cause a failure to meet the UL standard requirements.
In stallation and operation instructions are provided with each GP,These
installation instructions contian the follwing statements.
1.Power,input and output(I/O)wiring must be in accordance with ClassⅠ,Division2 wiring methods,
Articls 501-4(b) of the National Electrical Code, NFPA 70 or as specified in Secction 18-152 of the
Canadian Electrical Code for installations within Canada and in accordance with the authority
having jurisdiction.
2.Suitable for use in ClassⅠ,Division2,GroupsA,B,C and D hazardous location, or nonhaxardous
locations only.
3.WARNING:Explosion hazard-substitution of components may impair suitability for Class Ⅰ
,Division2,
4.WARNING:Explosion hazard-do not disconnect equipment unless power has been switched off or
the area is known to be nonhazardous.
5.WARNING:Explosion hazard-when in hazardous Iocations, tum off power before re placing or
wiring modules.
GP-370 Series User's Manual vii

What is IP65f ?
This unit's protection rating of IP65f is actually a composite code, consisting of the interna-
tionally recognized British "Ingress Protection" standard (BS EN 60529:1992) - "IP65",
and the standard developed by the Japanese Electronics Manufacturer's Association (JEM)
- "f". This code is used in this manual to identify a given product's degree of structural
resistance to a variety of environmental elements and thus, prevent problems or accidents
related to the inappropriate use of a product.
The individual meaning of each character of this code is explained below. This code indi-
cates the degree of ingress protection provided from the front face of the PL, and assumes
that the PL is securely mounted into a metal panel.
IP 6 5 f
(1) (2) (3) (4)
(1) Designates the type of protection provided.
(2) Indicates the degree of protection provided to the human body by the unit, and the
degree of protection provided by the unit's front face from particles/dust intrusion into
the interior of the unit.
Here, "6" indicates that the unit is completely protected from dust intrusion.
(3) Indicates the degree of protection provided by the unit's front face from water intrusion
into the interior of the unit.
Here, "5" indicates that the unit is protected from water intrusion from a direct water jet.
(4) Indicates the degree of protection provided by the unit's front face from oil particle intru
sion into the interior of the unit.
Here, "f" indicates that the unit is completely protected from oil intrusion via either oil
particles or oil splashes from any direction (to the front panel).
viii GP-370 Series User's Manual

Package Contents
The GP box contains the items listed below. Ensure everything illustrated has been
included.
• GP Unit • Handling Guide

(GP370-LG11-24V, GP370-SC11-24V,
GP370-LG41-24VP, GP370-SC41-24VP)
• Installation Fasteners (4/set)
This unit has been carefully packed, with special attention to quality. However, should
you find anything damaged or missing, please contact your local GP distributor imme-
diately for prompt service.
* This manual (GP-370 Series User's Manual) is sold separately.
GP-370 Series User's Manual ix

Symbols
The list below describes symbols and abbreviations used in this manual.
Warns a situation that could seriously injure a person or lead to

death if the GP is used in a wrong way or the warning is ignored.
Explains a situation that could injure a person ir damage materi-

als if the GP is used in a wrong way, or the warning is ignored.
Explains a situation that requires a moderate amount of caution.
GP Screen Represents the “GP-PRO/PB III” or “GP-PRO/PB III for

Editing Windows 95” software.
software
PLC Programmable Logic Controller
*1
A reference point. Describes the word or phrase marked by the
asterisk (*) and the corresponding number.
Indicates a word or phrase that may require additional explana-

tion.
Reference pages on related topics.
n:1 n:1 (multi-link) connection setup.
x GP-370 Series User's Manual

Chapter 1
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
Introduction
12345678901234567890123
12345678901234567890123
12345678901234567890123
1. 12345678901234567890123
Before Operating GP
2. 12345678901234567890123
12345678901234567890123
System Structure
12345678901234567890123
3. 12345678901234567890123
Optional Equipment
12345678901234567890123
12345678901234567890123
12345678901234567890123
1.1 Before Operating GP
Follow these steps before operating the GP unit.
1 Preparation Before using the GP, arrange the hardware and

check the specifications, wiring, and installation.
Chapter 2, "Specifications", and
Chapter 3, "Installation and Wiring".
2 Screen Design Draw a Screen and design a Tag layout, using the
Screen layout sheet and Tag list provided in your
manual.
3 Select GP type and PLC

Using your screen design software, select GP type
and the PLC host that is connected to the GP unit.
Software Operation Manual.
4 Create Screen/ Run Screen Setup

Setup the screen, parts and tags in your screen
editing software, while referring to your screen
design.
Software Operation Manual and
Software Tag Reference Manual.
5 Screen Data Transfer Transfer the data from the Screen design software
on your PC to the GP unit using the Downloading
Cable (included w/ the screen design software).
GP-PRO/PB3 Software Operation
Manual.
GP-370 Series User's Manual 1-1

Introduction
6 Initialize Following the specifications of the PLC host in

use, initialize the setup of the GP unit.
Chapter 4, "Initialize", and Software
PLC Connection Manual.
7 Run Link the GP with the PLC host using the Con-
nection Cable (different cables may be necessary
for different hosts), then run the System.
Software PLC Connection Manual.
1.2 System Structure

The diagram on the following page illustrates the peripheral equipment of the GP unit.
Legend
GP Interface PLC Interface PC Interface

Tool Connector RS-232C Port Printer Interface
Serial Interface RS-422 Port
Program Port
Screen Editing Environment
GP Operating Environment
Optional Parts
Optional items sold separately.
Maintenance Parts
These items are originally included with or in the package of GP
unit. They can also be purchased separately for replacement.
1-2 GP-370 Series User's Manual

Introduction
GP Unit
GP370-LG11-24V GP370-LG41-24VP
GP370-SC11-24V GP370-SC41-24VP

Screen Design Software
*1 GP-PRO/PBIII
Downloading Cable IBM Personal Computer GPPRO3-SU01M-V*
(included in software package) or compatible
GP-PRO/PBIII
GPPRO3-PB01M-V*
GP-PRO/PBIII for Windows 95
Bar Code Reader GPW-PB01M-V* (CD)
(recommended *2 ) GPW-PB02M-V* (FD)

Memory Loader *3
GP070-MU01-0
Printer
(EPSON ESC/P24-84
or equivalent)
RS-232C Cable *4
GP410-IS00-0

RS-422 Cable *4
GP230-IS11-0
GP230-IS12-0 (Multi-link cable)
RS-422 Connector *4
Terminal Exchange Adapter
GP070-CN10-0 Host Controller
e.g. PLC
Mitsubishi PLC A-Series

2 Port Adapter
GP030-MD11-0
Siemens Simatic S5 Series
Program Port I/F Cable
GP000-IS11-0
Mitsubishi PLC A-Series

GP430-IP10-0
Mitsubishi PLC FX-Series

GP430-IP11-0

Introduction
Optional Part
Cover Sheet
GP370-COVER-20P
Maintenance Parts
GP-370 Backlight Bulbs

GP370-BL00-MS
GP-70 Series Installation Fasteners

GP070-AT00-MS
Rubber Gasket
GP370-WP00-MS
*1 There are cases where only a limited PCs can be used.

*2 AIMEX manufacturer
• BR-331 PC2 (Pen-type)
OPT Electronics manufacturer
• OPT-1125-WL 98 (Touch Scanner) •OPT-1125-WD 98 (Keyboard)
• OPT-5125-WL 98 (Touch Scanner) •OPT-5125-WD 98 (Keyboard)
• LT-2125-WL 98 (Touch Scanner) •OPT-2125-WD 98 (Keyboard)
*3 Cannot be used with system versions 1.20 or higher.
6-1-1 Powering Up
*4 Certain types of PLC's cannot be connected.

Introduction
1.3 Optional Equipment

All optional equipment listed below are products of Digital Electronics Corp.
ITEM DESCRIPTION
GP-PRO/PB III GP-PRO/PB III
(GPPRO3-SU01M-V*) PC based Screen design Software for use with the
GP-PRO/PB III Digital GP-*70 Series of display panels.
(GPPRO3-PB01M-V*) Includes download cable to connect the PC and
Screen
GP-PRO/PB III for GP.
Editing
Windows 95
Tool
(GPW-PB01M-V*
:CD-ROM)
(GPW-PB02M-V*: FD)
<available from Feb. '97>
RS-232C Cable *1 I/F Cable to connect the GP unit with the PLC.
(GP410-IS00-O)
RS-422 Cable *1
(GP230-IS11-O)
Multi-link Cable*1 Runs multi-link (n:1) SIO between each PLC type
(GP230-IS12-O) and GP series. RS-422 interface cable.
RS-422 Terminal *1 Adapter for changing the terminal output from a
Connector Adapter serial interface to RS-422 I/F.
(GP070-CN10-O)
Siemens Simatic Series TTY converter cable for Siemens Simatic S5
Programming Port I/F Series PLCs. You would not be able to use a
Serial Connection Cable program console at the same time.
Interface (GP000-IS11-O)
Mitsubishi A Series Connects directly to Mitsubishi's FX Series I/F
Programming Port I/F Programming Console, making the conversion link
cable unit unnecessary. However, cannot use a program
(GP430-IP10-O) console at the same time.
Mitsubishi PLC FX
Series Programming Port
I/F Cable
(GP430-IP11-O)
Mitsubishi PLC A Series An interface unit that enables use of the GP Series
2 Port Adapter and Mitsubishi A series equipment in the same
(GP030-MD11-O) location.
*1 Certain types of PLC's cannot be connected. Software PLC Connection

Manual.

Introduction
ITEM DESCRIPTION
Option Cover Sheet Disposable GP screen protection from dust and
Part GP-370 other elements. The GP can be used with the Cover
(GP370-COVER-20P) Sheet still attached to the GP screen. (20/set)
Mainte- GP-370 Backlight Replacement Backlight bulbs.
nance Bulbs
Parts (GP370-BL00-MS)
GP-70 Series Metal installation brackets for GP-470/570/370/270
Installation Fasteners Series.
(GP070-AT00-MS)
Rubber Gasket Rubber gasket for installing the GP.
GP-370 Series
(GP370-WP00-MS)
Tool Memory Loader Runs a high speed data copy from one GP to another
Connector (GP070-MU01-O) (System program and Screen data).
Cannot be used with system versions 1.20 or higher.

Chapter 2
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
Specifications
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
1. General Specifications 4. Names and Functions of GP Parts
12345678901234567890123
12345678901234567890123
2. Function and Performance 5. Graphic Panel Dimensions
12345678901234567890123
12345678901234567890123
3. Interface Specifications
12345678901234567890123
12345678901234567890123
12345678901234567890123
2.1 General Specifications
1. Electrical Specifications
GP370-LG** GP370-SC**
Input Voltage DC20.4V~27.6V
Power
under 20W (TYP 10W)
Consumption
Voltage AC1000V 10mA 1minute
Endurance (between the live wire and grounding terminals)
Isolation Above 20MOhm at DC500V

Resistance (between the live wire and grounding terminals)

Specifications
2. Environmental Specifications
GP370-LG** GP370-SC**
Operating
0 ~ 50 degrees Celcius
Temperature
Storage
-20 ~ 60 degrees Celcius
Temperature
Ambient Humidity 20 ~ 85%RH (non-condensing)
Vibration Endurance 10 ~ 25 Hz (X,Y,Z directions 30 minutes 2G)
Noise voltage: 1000 Vp-p

Noise Endurance Pulse length: 1 microsecond
Arise time (rise/fall): 1 nanosecond
Atmosphere Not immune to corrosive gas
Ground Connection Ground resistance under 100 Ohms
Suitable
Equivalent for IP65F,
to JEM1030 IP65f and
Protective Structure *1 NEMA#250
NEMA#250 TYPE4X/13
TYPE4X/12
(However, does not protect against freezing)
*1 The front face of the GP unit, installed in a solid panel, has been tested
using conditions equivalent to the standards shown in the specification .
Even though the GP unit’s level of resistance is equivalent to these
standards, oils that should have no effect on the GP can possibly harm
the unit. This can occur in areas where either vaporized oils are present,
or where low viscosity cutting oils are allowed to adhere to the unit for
long periods of time. If the GP’s front face protection sheet becomes
peeled off, these conditions can lead to the ingress of oil into the GP and
separate protection measures are suggested. Also, if non-approved oils
are present, it may cause deformation or corrosion of the front panel’s
plastic cover. Therefore, prior to installing the GP be sure to confirm the
type of conditions that will be present in the GP’s operating environment.
If the installation gasket is used for a long period of time, or if the unit
and its gasket are removed from the panel, the original level of the
protection cannot be guaranteed. To maintain the original protection
level, you need to replace the installation gasket regularly.
3. Structural Specifications
GP370-LG** GP370-SC**
External 170W × 138H × 57D mm
Measurements (mm) (GP unit only)
Weight Under 900g (GP unit only)
Cooling System Natural air circulation

Specifications
2.2 Function and Performance
1. Display Functions
GP370-LG** GP370-SC**
Display Media Monochrome LCD STN Color LCD
Display Color White, Black 8 colors (white, red, blue,

green, yellow, magenta, cyan,
black) Tiling patterns make
blends of colors possible
Back light CFL (under normal temperatures and humidity, lifespan =

20,000 hours)
Resolution 320 × 240 pixels
Display Area 115W × 86H (mm)
Attributes Blink/ Reverse Video
Contrast The Touch Panel has 8 levels of contrast adjustments available

Adjustment
Characters Korean: (KSC5601-1992 codes) Hangul fonts (including Kanji)
Chinese: (GB2321-80 codes) simplified Chines fonts

Taiwanese: (Big 5 codes) traditional Chinese fonts
ASCII: (Code Page850) Alphanumeric (including European fonts)
Japan: ANK 158 type, Kanji:6349 (includes non-Kanji:453, and

Standard JIS Type 1 and Type 2)
8x8 dot font: 40 Char. per row, 30 rows

Char. Disp. # 8x16 dot font: 40 Char. per row, 15 rows
16x16 dot font: 20 Char. per row, 15 rows
Character Size Height and width can be expanded by 2, 4, or 8.

Specifications
2. Screen Memory
GP370-LG** GP370-SC**
FLASH EPROM 1 Mbyte
Internal Memory (Up to 320 screens w/ a standard screen size of 3.2 Kbytes)
3. Touch Panel / Clock Accuracy
GP370-LG** GP370-SC**
Touch Panel 16 × 12 keys/ screen (1 or 2 point touch)
Clock
+/- 40 seconds/ month (at room temperature)
Accuracy
4. External Interface
GP370-LG** GP370-SC**
Serial Asynchronous Transmission Method: RS-232C/RS-422
Interface Data Length: 7 or 8 bits
Stop Bit: 1 or 2 bits
Parity: None, Odd or Even
Data Transmission Rate: 2400~38400bps
Tool RS-232C Asychronous Transmission TTL level non-procedure
Connector command interface
(During Development) use the I/F to download Screen design
(During RUN mode) use with the BarCode Reader I/F

Specifications
2.3 Interface Specifications
1. Serial Interface
Pin Signal Condition Pin Signal Condition
SIO # Name # Name
1 FG Frame ground 14 VCC 5V + 5% output 0.25A
2 SD Send data (RS-232C) 15 SDB Send data B (RS-422)
3 RD Receive data (RS-232C) 16 RDB Receive data B (RS-422)
13
25 4 RS Request send (RS-232C) 17 NC No connection
5 CS Clear send (RS-232C) 18 CSB Clear send B (RS-422)
6 NC No connection 19 ERB Enable receive B (RS-422)
7 GND System ground 20 ER Enable receive (RS-232C)
8 CD Carrier detect (RS-232C) 21 CSA Clear send A (RS-422)
9 TRMX Termination (RS-422) 22 ERA Enable receive A (RS-422)
10 RDA Receive data A (RS-422) 23 BUZZ GND External Buzzer ground
11 SDA Send data A (RS-422) 24 NC No connection
12 NC No connection 25 BUZZ OUT External Buzzer output
14
1
13 NC No connection
Recommended Connector: Dsub25pin plug XM2A-2501<made by OMRON Corp.>

Recommended Cover : Dsub25pin Cover XM2S-2511<made by OMRON Corp.>
Dsub25pin plug XM2A-2501<made by OMRON Corp.>
Use rough metric type M2.6×0.45p threads used to hold the cable's set
(fastening) screws in place.
Recommended Cable : CO-MA-VV-SB5P×28AWG <made by HITACHI Cable Ltd.>
Software PLC Connection Manual to determine your PLC's con-
nection points.
When creating your own cable, follow the instructions listed below
concerning each connection type.
RS-422
The following pairs of pin #'s must be connected to each other.
....... #18 (CSB) <—> #19 (ERB)
....... #21 (CSA) <—> #22 (ERA)
• When connecting the RS-422 cable and the #9 (TRMX) and #10 (RDA)
points, a termination resistance of 100Ω is added between RDA and RDB.
• When making a cable for the Memory Link format, be sure to select
a 4-line System.
RS-232C
• Do not use the following pins:
9 (TRMX), 10 (RDA), 11 (SDA), 15 (SDB), 16 (RDB), 18 (CSB), 19
(ERB), 21 (CSA), 22 (ERA).
Specifications
GP-370 Serial Interface Connections
External Buzzer Output 5~24V

Buzzer 0.1~0.3A
SIO drives the buzzer
Internal Circuit 25 PIN
Route 5~24V
SIO
Light isolation 23 PIN
Internal GP-370 Series
2.4 Names and Functions of GP Parts
A: Display Type.
The GP monitor screen displays the
screen setup and corresponding PLC
host data.
GP370-LG** Monochrome LCD
GP370-SC** STN type Color LCD
B: Touch Panel
Runs any screen change operations
and sends data to the PLC.
C A,B C: Power Lamp

Lights up when the power is turned
On. (Green LED)
D: Power Input Terminal Block
Power cable connection.
E: Extension Interface
This I/F will be used in future ver-
sions.
F: Serial Interface
Connect the RS-232C and RS-422
(Serial) interface to the PLC host.
D E F G G: Tool Connector
The Transfer cable, Bar Code reader,
and Memory Loader connect here.

Specifications
2.5 Graphic Panel Dimensions
1. GP-370 Series External Dimensions

Unit: mm
Top View
155.5
120
10
Front View Side View
115.2
86.4
123
138
170.5 5
57
Rear View
41

Specifications
2. Installation Fasteners
Units: mm
Top View Rear View
27
16
19.5
∅10
M5 8
Front View Side View
11
1.6
3
4.6
3. GP Installation Dimensions
Unit: mm
Mounting Hole for Installation
12345678901234567890
+1
156 - 0
12345678901234567890
12345678901234567890
12345678901234567890
12345678901234567890
12345678901234567890
12345678901234567890
123.5-
12345678901234567890
12345678901234567890
12345678901234567890
+1
12345678901234567890
0
12345678901234567890
12345678901234567890
12345678901234567890
12345678901234567890
12345678901234567890
less than 4-R3

Chapter 3
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
Installation and Wiring
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
1 . Installation 3 . Tool Connection
12345678901234567890123
12345678901234567890123
2 . Wiring
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
3.1 Installation
When installing the GP unit, use the tips listed below
Before mounting the unit, please make sure the gasket is attached to the unit.
Vie B a GP
w ck
Gasket
1. Installation
Install the GP unit following these steps.

Create an Opening
Following the GP Installation dimensions, create the opening required for GP installa-
tion. The rubber gasket, installation brackets, and screws are necessary when install-
ing the GP. Chapter 2.5, "Graphic Panel Dimensions".
Panel
Installation
Opening
• It is important that the plate surface is flat, in good condition, and without
any jagged edges.
• Panel thickness should be between 1.6mm and 5.0mm.
1.6 ~ 5mm

• For easier maintenance and operation, plus better ventilation, ensure the
GP unit is mounted at least 100 mm away from adjacent structures and
other parts.
• The GP uses ventilation in its outer shell to naturally cool itself. When
installing the unit horizontally or sideways, use a forced air cooling system
(i.e. a fan) or lower the surrounding temperature to avoid overheating.
Vertical Installation
Screen Face
Side View
Horizontal Installation
Sideways Installation

• When installing sideways, place the GP so that the Power Terminal Block points
upwards.
• Ensure heat from other equipment does not cause extra heating pressure on the
GP.
• Do not use GP-370 Series in an environment that exceeds 50o C.
• Ensure that this unit is located as far away as possible from electromagnetic cir-
cuits, non-fuse type breakers, and other equipment that can cause arcing.
• When installing the GP unit, with natural air circularion cooling system, onto a
slanted panel, the panel slope should not incline more than 30o.
less than 30o
Install the unit from the front of the panel opening. Panel
Side View
Secure the Installation brackets from the backside of the panel.

There are 4 insertion slots on the top and bottom of the GP, where the metal installa-
tion brackets hook on.

Top/Bottom View

Installation Bracket
Panel
Front Side Back Side
Insertion
Slot
After inserting the brackets into the appropriate slots, carefully force the
bracket to the back of the GP.
Use a screw driver and tighten the screw from the back to hold the GP
unit in place. A torque of 0.5~0.6N•m is required to tighten the screw.
Using too much force may damage the GP unit.

3.2 Wiring
1. Power Cable Connection
• To avoid electric shocks, be sure the Power Cable is unplugged

from the power outlet when connecting the cable to the GP unit.
• GP-370 Series can only take DC24V input. If you supply power
other than DC24V, you will damage its power supply and the GP
unit.
• There is no power switch on the GP unit, so please use a breaker
switch.
When the FG terminal is connected, be sure the wire is grounded. Not ground-
ing the GP unit will result in excess noise.
• Wherever you can, use thick wires (max 2mm2) for power terminals,
and provide an extra twist to the wire during connection.
• Please use Ring Terminals with the size described below.
over Ø3.2mm
under
6.0mm
• To avoid a short among the ring terminals when the screws get loosen,
please use ring terminals with a sleeve.
GP-370 SeriesBackside
+
+ — FG
Crimp-on Ring
Terminals*1
FG
Power Terminal Block
Connect the GP power cables following the steps below.

Check to make sure the Power is Off.
Remove the Terminal cover.
*1 Ring Terminals: V2-MS3 suitable (made by JST)

Disconnect the screws from the 3 terminals, align the power wire rings and re-
insert the screws. (Check each wire to make sure the connections are correct.)
The torque required to tighten the screws is 0.5~0.6N•m.
2. Precaution: Grounding
(a) exclusive grounding (BEST) Connect the FG terminal found at the

back of the unit to an exclusive ground.
GP unit other
[diagram (a). There is a grounding re-
equipment
sistance of under 100Ω.]
If exclusive grounding is not possible,

use a common connection point. [dia-
gram (b)]
(b) common grounding (OK)
The grounding wire should have a
GP unit other
cross sectional area greater than 2mm2.
equipment
Set the connection point as close to
the GP unit, and make the wire as
short, as possible. When using a long
grounding wire, replace the thin wire
with a thicker wire placed in a duct.
(c) common grounding (BAD) If this equipment does not function

GP unit other properly when grounded, disconnect
equipment the ground wire from the FG termi-
nal.
3. Precaution: Input/Output Signal Lines
Input and output signal lines must be separated from the power control ca-
bles for operating circuits.
If this is not possible, use a shielded cable and connect the shield to the frame
of the GP unit.

3.3 Tool Connector

The Downloading Cable or a Bar Code Reader fits into the Tool Connector
socket.
Side View
Tool Connector
• When inserting or removing items from the Tool Connector socket, be

sure the GP unit has been turned Off.
• When the Bar Code Reader uses a different power supply:

—Turn the Bar Code Reader on before turning the GP unit on.
—Turn the GP unit off before turning the Bar Code Reader off.

1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
MEMO
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901

Chapter 4
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
Off-line Mode
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
1. Entering Off-line Mode 4. SELF-DIAGNOSIS—Standard Operations
12345678901234567890123
12345678901234567890123
2. Main Menu 5. Transfer Screen Data
12345678901234567890123
12345678901234567890123
3. INITIALIZE—Standard Operations
12345678901234567890123
12345678901234567890123
12345678901234567890123
4.1 Entering Off-line Mode
The Off-line Mode refers to Initialize, Self-Diagnosis, and other setups con-
tained in the GP. Prepare the GP unit in the Off-line mode before running any
operations.
The Off-line mode is unavailable in a brand new GP until Screen Data

has been transfered from the corresponding screen editing software.
Note: Be sure that the GP is turned ON when transferring the system file.
To INITIALIZE the setup or run SELF-DIAGNOSIS in the GP unit, transferring to the

Off-line mode becomes necessary. There are 2 ways to enter the Off-line mode:
number one, when turning the unit on, and number two, using Force Reset.
1. When Turning the Unit On
Press the top left corner of the GP screen within 10 seconds of switching the power
On.
System Version Current Date/Time
Protocol Name and Protocol Version

Off-line Mode
2. Enter From Force Reset
From the Force Reset screen, press the OFFLINE button.
For more information about Force Reset Chapter 5.4.2, "SET UP I/O".
• When the GP unit has the Device Monitor function, the following display
will appear. GP-PRO/PBIII for Windows 95 Software PLC
Connection Manual, Appendix 3 "Device Monitor".
If a Password has been set in INITIALIZE/ SET UP SYSTEM, before entering the
Off-line mode, the following screen displays.
Enter the password, then press Set to enter Off-line mode.
Only the GP-PRO/PBIII for Windows 95 can utilize this Device Monitor function.
For more about the Password, Chapter 5.3.1, "SYSTEM Environment
SETUP".
For more infomation on the password input Chapter 4.3, "INPUTTING
NUMBERS".

Off-line Mode
4.2 Main Menu

The Main Menu includes the setup items listed below: INITIALIZE, SCREEN DATA
TRANSFER, SELF-DIAGNOSIS, and RUN. Each menu item has different setups
that must be set to match the corresponding PLC in order for the GP to commu-
nicate properly.
Entering the Off-line mode displays the screen illustrated below.
Select the menu item by pressing the title on the screen.

A short description of each Main Menu item follows.
INITIALIZE
The setup items listed in this menu are necessary to run the GP unit.
TRANSFER SCREEN DATA
Select to transfer screen data to and from the screen editing software.
SELF-DIAGNOSIS
Checks to see if there are any problems with the GP System or Interface (I/F).
RUN
Begins operations in the GP unit.
For more information about INITIALIZE, refer to Chapter 5, "Initial-

ize"; for more information about TRANSFER SCREEN DATA, refer to the Software
Operation Manual; for more information about SELF-DIAGNOSIS and RUN, refer
to Chapter 6, "Run and Errors".

Off-line Mode
4.3 INITIALIZE—Standard Operations

Selecting A Menu
• Press the menu title to setup.
• Press the menu item you wish to setup.
Inputting Numbers
• After selecting an input field by touching it, use the numeric touch keys that appear
next to enter numeric values.
Selecting Setup Conditions

• After selecting the menu item, press the option you would like to setup. In this
example, pressing the TOUCH BUZZER SOUND turns that option Off.

Off-line Mode
Ending Setup
To end setup, you would usually press the top-left button, SET.
If you wish to exit the screen without saving the changes, press the ESC button.
• Press the SET key to write the Setup condi-
tions onto the Internal FEPROM, which may
take some time, causing a delay in returning
to the previous screen. Therefore, do not
touch the screen until the previous menu dis-
play returns.
• Press the CANCEL key to not write the Setup
conditions onto the Internal FEPROM and re-
turn to the previous menu.
Return To Previous Screen

Press the title of the screen you would like to return to.
E.g. To return to the MAIN MENU from the SYSTEM ENVIRONMENT SETUP
screen, simply press the MAIN MENU title.
4.4 SELF-DIAGNOSIS—Standard Operations

Selecting A Menu
Press the title of the menu item to diagnose.

Off-line Mode
SET, ESC Keys

After selecting the SELF-DIAGNOSIS item, the and keys appear at dif-
ferent times at the top of the screen.
E.g.
• SET Key
When this key is pressed, the Self-Diagnosis begins.
• ESC Key
When this key is pressed, the Self-Diagnosis command is cancelled, and you
return to the Self-Diagnosis menu.
After Check—To Return To SELF-DIAGNOSIS MENU
When OK displays, pressing once

anywhere on the display screen
returns you to the SELF-DIAGNO-
SIS MENU.
When an Error Message displays
When an error message appears

on the display screen, press the
bottom two corners of the panel
(1, 2) to return to the
SELF-DIAGNOSIS MENU.

Off-line Mode
Return To Main Menu

Press the MAIN tab in the SELF-DIAGNOSIS menu to return to the MAIN MENU.
4.5 Transfer Screen Data

The process required to transfer screen data to the GP, or to receive data from
the GP, is described here.
Link up the GP's tool connector, located at the back of the GP, with your PC's
RS-232C connector using the Downloading cable.
PC (rear view) GP-370 Series(side view)
RS-232C
Adapter
Downloading Tool Connector

Cable

Off-line Mode
• Use an adapter to match the cable with your PC's Serial Port format.
• When using a serial mouse, use a serial port other than that of the mouse.
Prior to transmitting data, be sure to set the GP to either TRANSFER SCREEN
DATA or RUN mode. Note: With a newly purchased GP, be sure it is turned ON
before transmitting data.
Be sure that the GP screen editing software is set for either sending screen data to the
GP, or for receiving data from the GP.
Software Operation Manual, 4-2 "Send to GP/Receive from GP"
After setting up the GP, return to your screen GP, "Transferring, Please Wait". Once
the message ends, transfer is complete.
Press the ESC key to return the GP to RUN mode. If a Screen File Number has been
setup in GP's INITIALIZE setting, then that screen will display. If no screen number has
been setup, then the GP will return to the MAIN MENU.
*1 Setup means to download GP's system program and a PLC protocol driver, from a screen editor
software, in order to run the GP in a desired environment.

Chapter 5
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
Initialize
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
1. Initialize Screen 5. PLC SETUP
12345678901234567890123
12345678901234567890123
2. Initialize Items 6. INITIALIZE MEMORY
12345678901234567890123
12345678901234567890123
3. SYSTEM ENVIRONMENT SETUP 7. SET UP TIME
12345678901234567890123
12345678901234567890123 8.
4. SET UP I/O SET UP SCREEN
12345678901234567890123
5.1 Initialize Screen
Before running the GP unit, various GP setups must be verified. These are
listed under the INITIALIZE option in the MAIN MENU.
This chapter explains each of the Off-line mode's INITIALIZE items. However,
there are 2 types of INITIALIZE setups, the 1:1 connection and the n:1 (multi-link)
connection*1, and the setup information can differ for each.
The n:1 mark appears on menu items concerned only with the n:1 multi-link
connection. If there is no mark, the menu item is common to both 1:1 and n:1
connections.
1:1 Process concerning 1 GP connected with 1 PLC.

n:1 Process concerning multiple GP's connected with 1 PLC. The GP's
successively pass a token (exclusive PLC interaction key) among them-
selves to communicate with the PLC.
If you transfer your screen editing software's System file*2, the GP

operates using the data contained therein. If the GP System file has
been correctly setup and transferred, the INITIALIZE setups become un-
necessary.
For more information about System file (S0) Software Op-
eration Manual,1.1.2 "Screen Types"
*1
PLC's that support the n:1 (multi-link) connection are limited.
*2
While "S0" is used in the case of GP-PROIII and GP-PRO/PBIII, GP-PRO/PBIII for
Windows 95 uses "Settings."

Initialize
5.2 Initialize Items

The contents of the Initialize setup items listed below are explained in this chapter.
To learn about screen operations and numeric input Chapter 4, "Off-
line Mode".
1 SYSTEM ENVIRONMENT SETUP
System Setup
System Area Setup
Global Window Setup
Character String Data Setup
2 SET UP I/O
Set Up SIO
Set Up I/O
Communication Setup
3 PLC SETUP 1:1

Set Up Operation Surroundings
3 PLC SETUP n:1

Set Up Operation Surroundings
Station Setup
Customize Setup
4 INITIALIZE MEMORY
5 SET UP TIME
6 SET UP SCREEN
7 FONT SETTING

Initialize
5.3 SYSTEM ENVIRONMENT SETUP

GP environment adjustments are made here. The SYSTEM ENVIRONMENT
SETUP includes the SYSTEM SETUP, SYSTEM DATA AREA, GLOBAL WINDOW
SETUP, and CHARACTER STRING DATA SETUP.
1. SYSTEM SETUP
STAND-BY MODE TIME (0-255)

To protect the GP display screen, GP has been setup with a screen saver func-
tion that automatically erases the screen when no GP operations have occurred
for the time entered here. A 0 entered in this field causes a normal display.
When SYSTEM DATA AREA's ( Software PLC Connection Manual)
*1
SCREEN DISPLAY OFF data is 0000h, and the following operations are not
performed on the screen for the number of minutes setup, the GP display erases.
• Change Screen
• Touch Screen
• Alarm Display
START TIME (0-255)

This setup determines the start-up time of the GP. Use this setup to adjust the
power up sequence so that the GP starts up after the PLC.
TOUCH BUZZER SOUND

Setup whether or not the GP beeps when pressed.
BUZZER TERMINAL OUTPUT

Setup whether or not the BUZZ signal is output from GP's AUX I/F. This op-
tion is for an external buzzer.
PASSWORD SETUP (0-9999)

The passsword setting is used when changing to the Initialize Memory or Ini-
tialize (off-line mode) screens.
*1 When using the Direct Access format or the Memory Link format, the object address
becomes +9 or +12 respectively.

Initialize
The password (number) ensures protection of the GP setups as Off-line mode

will not be entered inadvertently. Enter the optional number of your choice. If
you do not wish to use this setup, enter the default 0.
Data Type of Screen No.
This setup controls whether BIN or BCD format numbers are used when making
screen changes. Screen numbers 1~8999 are available when set up in binary
format; screen numbers 1~1999 are available when set up in BCD format.
2. SYSTEM AREA SETUP
SYSTEM AREA SETUP is necessary for the PLC to administer the GP, and
prepare the PLC internal Data Memory (DM) and Data Register (D)*1. Use this
setup to prepare the desired SYSTEM DATA AREA items. When using the
Memory Link format, this setting is unnecessary.
Press the and buttons to toggle between the SYSTEM AREA WRITE
and READ screens.
Press the item—when the item is highlighted, it is selected.
System AREA SIZE
This field displays the size, in words, of the items selected in the SYSTEM AREA
(all the WRITE and READ items).
When you press the SET key, the SYSTEM AREA CONTENTS screen appears and
ratifies the selected items
• The setup shown is efficient only when using the Direct Access format.
• The selected System Area items, as displayed on the screen, become
the System Data Area.
When these five items, "Current Screen Number", "Error Status", "Clock Data (Cur-
rent)", "Change Screen Number", and "Display On/Off", have been selected, word
addresses are assigned to each item, in order, as shown on the next page.
*1
Data Memory (DM) refers to OMRON Co.'s PLC; Data Register (D) refer
to Mitsubishi Electric Co.'s PLC.
Initialize
Addresses LS16 to LS19 are

fixed as they control the Global
Window. Other items cannot be
set to these addresses.
The System Data Area selection process follows this formula [System Data Start
Address + n]. For example, if the System Area Start Address was D00200, and the
Change Screen Number option had been selected—if you refer to the System
Area Contents screen displayed above—because Change Screen Number's ad-
dress is pegged at +6, its word address would be D00200+6=D00206.
For more information on the LS area 16~19 Software PLC Connec-
tion Manual,1.1.2 "LS Area Structure"
3. GLOBAL WINDOW SETUP
The GP unit can display one Global Window and two Local Windows at any
one time. The Global Window is common to all the display screens. The Local
Window displays exclusively on the corresponding base screen. The GLOBAL
WINDOW SETUP is described here.
GLOBAL WINDOW
When first entering the Global Window, select whether to Use, or Do Not Use the
Global Window. If you select Do Not Use, ignore the items described below.
Selecting Use makes these options available by simply pressing the NEXT button.
GLOBAL WINDOW ACCESS
Setup the Global REGISTRATION NO. and the Window LOCATION as Direct or
Indirect values. When set as Direct, the REGISTRATION NO. and Window LO-
CATION selection are fixed to the values setup here. When set to Indirect, the
WINDOW REG. NO. word address as prepared in the System Area is variable—
which means it can have the REGISTRATION NO. written to it, and as a result,
multiple window screens can be used as the Global window. Adjust the Global
Initialize
window position using this same method, by writing the X,Y coordinates to the
SYSTEM AREA's WINDOW LOCATION word addresses.
DATA FORMAT
Setup whether the REGISTRATION NO. and the Window LOCATION values are in-
putted as BIN or BCD numbers. Only Direct values can be setup in these fields.
REGISTRATION NO. (1-256)
Setup the Window Screen Number used by the Global Window. This field is
applicable only when the GLOBAL WINDOW ACCESS is set to Indirect.
LOCATION
Setup for the Global Window LOCATION. This field is applicable only when the
GLOBAL WINDOW ACCESS is set to Indirect.
4. CHARACTER STRING DATA SETUP
Character String Data ordering varies from manufacturer to manufacturer. Setup

the Character String Data order here to match the corresponding PLC.
Setup the CHARACTER STRING DATA MODE to match the PLC type.
Device type and Tag settings are unavailable.
Find the data storage order for your PLC in the table, next page, and setup the
CHARACTER STRING DATA MODE.
(I) Data Device Storage Order
(II) Internal Word Byte LH/HL Storage Order
(III)Internal Double-word Word LH/HL Storage Order

Initialize
CHARACTER STRING DATA MODE List

I) Data II) Internal III) Double-word Character
Device Word, Byte Internal Word String
Storage LH/HL LH/HL Storage Data Mode
Order Storage Order Order
Storage LH order 4
from Start LH order
data HL order 2
LH order 5
HL order
HL order 1
Storage LH order 6
from End LH order
Data HL order 7
LH order 8
HL order
HL order 3
I) Data Device Storage Order

E.g. Characters A B C D E F G H

• Storage from Start Data • Storage from End Data
D100 D100
D101 D101
D102 D102
D103 D103
II) Word Byte LH/HL Order

E.g. Characters A B C D

• 16 bit Device LH Order • 16 bit Device HL Order
D100 D100
D101 D101

D100 D100

Initialize
III) Double-word Word LH/HL Order

E.g. Characters "A B C D E F G H I J"

D100 D100
D101 D101
D102 D102
D103 D103
D104 D104
E.g. Characters "A B C D E F G H I J K L M N O P Q R S T"

D100 D100
D101 D101
D102 D102
D103 D103
D104 D104
Relationship between K-tag Write Character Value and PLC Device

• 16 bit Device
GP stores the character string from the start, as groups of 2, into1 PLC Device.
When there are nine characters, they are arranged as shown below.
1 2 3 4 5 6 7 8 9 NULL
When the characters do not divide into 2 evenly, NULL is added.
• 32 bit Device
GP stores the character string from the start, as groups of 4, into1 PLC Device.
When there are nine characters, they are arranged as shown below.
1 2 3 4 5 6 7 8 9 NULL
When the characters do not divide into 4 evenly, NULL is added.

Initialize
5.4 SET UP I/O

This section describes the communication setup with the host PLC and the
setup for any peripheral equipment. The SET UP I/O menu includes the SET UP
SIO, SET UP I/O, and COMMUNICATION SETUP menus.
1. SET UP SIO
This menu runs the setups related to PLC communication. Match the settings
listed below with the SIO setup on the PLC host side.
COMMUNICATION RATE
The COMMUNICATION RATE (baud rate) is the data communication speed, meas-
ured in bits per second (bps), between the GP and PLC. Match the COMMUNI-
CATION RATE values in both the PLC and GP.
DATA LENGTH
For data communications, the DATA LENGTH (the first numeral) must be set up
as 7-bit or 8-bit data. The second value is the STOP BIT, which must be set up as
either 1-bit or 2-bit.
PARITY
Set up whether no parity check, or an odd or even number parity check will take
place during communication.
CONTROL
Data flow CONTROL prevents the overflow of data sent back and forth. Select
either X-CNTRL or ER-CNTRL.
COMMUNICATION FORMAT
Select one of the following options for the communication format: RS-232C,
RS-422 4 line, or RS-422 2 line.
When communicating with the Memory Link format using RS-422,

select the 4-line option.

Initialize
2. SET UP I/O
Touch operation and Force Reset setup, and Display Device adjustments are
made here.
TOUCH OPERATION MODE

Set up either One Point or Two Point input.
FORCE RESET
Set up whether or not a FORCE RESET operation is in effect.
Steps to run FORCE RESET
While holding down the bottom right corner (1) of the screen, press the upper
right corner (2). At the same time, press the bottom left corner (3) to enter the
FORCE RESET Operation. To activate Reset, press the RESET button; to trans-
fer to Off-line Mode, press OFFLINE.
• FORCE RESET occurs even during RUN mode and Off-line mode.
• The FORCE RESET mode cannot be entered while waiting for the GP
to start.
• Entering FORCE RESET is possible even when RUN operations (PLC
<—>GP communication) do not occur.

Initialize
CONTRAST ADJUSTMENT
When this option is set On, CONTRAST ADJUSTMENTs can be made through
touch input.
While pressing the upper right hand corner (1) of the screen, press the upper left
corner (2) to enter CONTRAST ADJUSTMENT mode. Press the desired setting
and the screen's contrast will change accordingly.
• For the GP370-LG** models, the lighter and darker settigs are on the
opposite side.
• To exit CONTRAST ADJUSTMENT mode, press anywhere outside the

contrast option bar.
• CONTRAST ADJUSTMENT mode cannot be entered while waiting for
GP to start.
• CONTRAST ADJUSTMENTs can be made even in the middle of RUN
mode (PLC<—>GP communication).
BRIGHTNESS SETTING
When this is set to ON, brightness can be changed by simply touching the
screen.
For example, press the lower right (1) and lower left corners (2) of the screen
simultaneously to enable the Brightness Setting mode. In this mode, touching
the bottom left of the screen increases the brightness, and touching the bottom
right side decreases the brightness. (See the figure below)

Initialize
• This mode cannot be be enabled or used while the GP is starting up.

• This mode can be used even while the GP is running (i.e. while data
is being transmitted to and from the PLC).
LCD SETTING (Only for GP-370LG**)

There are two options: REVERSE and NORMAL. When set to REVERSE, the
screen lighting becomes inverted.
Press the LCD SETTING item to change it from NORMAL to REVERSE, then press
the SET button. The screen display reverses and returns to the previous screen.
3. COMMUNICATION SETUP
These fields set when an error message is reported, after a GP<—>PLC com-
munication error is detected. This ensures an error has actually taken place and
not just slight breaks in communication or slowness in processing data on one
side or the other.
RECEIVE TIMEOUT
Set up how long the GP unit will wait when there is nothing being sent to it.
(This is the Timeout Time.) However, if there is no cable connected up, then
regardless of the time set up here, the Timeout value would be 1 second. The
default value is 10 seconds.

Initialize
When a value of over 30 seconds is set here, and a screen is trans-

ferred from the PC while a PLC Communication Time error has oc-
curred, an error may also appear on the PC side.
RETRY COUNT
Set up the number of times the GP will try to send data when a Communication
error occurs. The default value is 2 times.
5.5 PLC SETUP

Setup the System Area and the Unit number on this screen. Because 1:1 and n:1 GP
connections change the setup contents, check it before running any setups.
With the GP-PRO/PBIII for Windows95 “Simulation” feature, the GP’s
“Setup Operation Surroundings” area cannot be used.
1. SET UP OPERATION SURROUNDINGS (1:1)
Setup the PLC System Data Area and the Unit Number here.
This setup is only necessary when using the Direct Access format.
SYSTEM AREA STARTING DEVICE / STARTING ADDRESS

Setup the PLC's Data Register (D), Data Memory (DM), etc. allotted by the SYSTEM
AREA STARTING ADDRESS. (The START DEV display changes with different PLC's.)
UNIT NO.
Set up the PLC UNIT number here. Make sure it matches the one set up in the PLC.
SYSTEM AREA READ SIZE

When using a Block Display Trend Graph, setup the Reading Area Size (in word
units) to match the Trend Graph's data size. Set this up when you wish to allocate the
Reading Area in the PLC Data Register (D), or Data Memory (DM).

Initialize
• If you are not using the Reading Area, leave the 0 default values intact.
High Speed Communications can be secured as a result.
• When using Hitachi's HIDIC-S10 α Series, an extra item titled "Extended
Memory Address (HIDIC) [000000]" is added to the above screen dis-
play. Values accepted by the extended memory start address are 0 (memory
not extended), and 100000~1FF000.
• When using Matsushita Electric's NEWNET-FP, an extra item titled

"Monitor Register" is added to the screen display. If using 2 or more
CCU's (communication unit) as in the following diagram, and a GP is
connected to each CCU, select the 1:1 connection and setup the Monitor
Register as "None".
• When connecting only one GP (to a PLC), be sure to set the Monitor
Register to ON.
2. SET UP OPERATION SURROUNDINGS (n:1)
This is the setup for the PLC System Data Area and the Unit Number for an n:1
(multi-link) PLC connection. For more about the SYSTEM DATA AREA with the
n:1 (multi-link) connection, Software PLC Connection Manual.
This setup is only necessary when using the Direct Access format.

Initialize
SYSTEM AREA STARTING DEVICE / STARTING ADDRESS

Setup the PLC's Data Register (D), Data Memory (DM), etc. allotted by the
SYSTEM AREA STARTING ADDRESS.
UNIT NO.
Set up the PLC UNIT number here. Make sure it matches the one set up in the
PLC.
SYSTEM AREA READ SIZE

When using a Block Display Trend Graph, setup the Reading Area Size (in
word units) to match the Trend Graph's data size. Set this up when you wish to
allocate the Reading Area in the PLC Data Register (D), or Data Memory (DM).
• If you are not using the Reading Area, leave the 0 default values
intact. High Speed Communications can be secured as a result.
3. STATION SETUP (n:1)
The STATION SETUP, necessary for the n:1 (multi-link) setup, checks whether
correct communications run with the connected GP System configuration.
NETWORK INFORMATION DEVICE / INFORMATION ADDRESS

In the n:1 (multi-link) connection, the Network Information uses 2 words in its
correspondences. These 2 words are the Connection part and the Validation
part (described later in this section). Allocate these respective areas into the
PLC's Data Register (D) or Data Memory (DM).
PLC Data Register
In the NETWORK INFORMATION ADDRESS, setup all the GP's connected

to the same link unit with the same address. Furthermore, when there
are 2 ports in the connected link unit, do not make these use the same
address.

Initialize
• Connection Part
The word address for the Connection Part sets up the number of GP's connected
to the PLC, registered beforehand on the PLC side. When these GP's are con-
nected to the PLC, the corresponding PLC bit numbers for the particular GP
Stations (see bottom) turn on.
When the GP is connected to the PLC, and the option of GP only

correspondence ends and Offline mode is entered, the GP Station
Number turns the corresponding PLC bit off.
Bit 15 Bit 0
For example, when these 4 GP units—bit 0, bit 2, bit 3, bit 5—are connected,
002D (h) is written here.
Connection Part 002D (h)
• Be certain to setup before running.

• Turn bits not connected to the GP off.
• Verification Part
This area responds to the correspondence from each connected GP. When the
same bit numbers as the Connection Part turn On, the correspondence is ac-
cepted by the Verification Part. In turn, the Station Numbers of the communi-
cating GPs turn their corresponding PLC bit number on.
Bit 15 Bit 0
If the correspondence between the GP and PLC is correct, the same value as in
the Connection Part writes to the Verification Part.
For example, the value 002D (h) in the Connection Part, setup as the 0 bit, 2 bit,
3 bit, and 5 bit, writes to the Verification Part as shown below.
Connection Part 002D (h)

Verification Part 002D (h)
• When the Connection Part and Verification Part do not match, a

COMMUNICATION ERROR occurs. Check the setup again.
• When changing the connection, first turn all the bits Off.
• Even if the GP is connected, if the Connection Part List is turned off,
data transfer cannot occur, and an error will not display.

Initialize
STATION NO.
This is the setup for the number of GP Stations in use, as mentioned in the
above section. The setup range is from 0 to 15, and the only other restriction is
each GP STATION NO. must be unique in the system. If STATION NO.'s are
repeated, a COMMUNICATION ERROR occurs.
• The STATION NO. is the number allocated to the particular GP unit.

This number is not related to the Link Unit Machine number.
4. CUSTOMIZE SETUP
The Customize function alters the n:1 (multi-link) connection's communication to make
it more effective. To run communication efficiently, determine whether to use Opera-
tion or Display priority with your GP. As a result, the communication response speed
can be upgraded, although the speed changes with the screen information.
PLC PRIORITY
According to how the GP is used, select either Operation priority (OPE.) or Display
priority.
• Display
Setup the GP to this option when using the GP mainly as a monitor screen. The GP
will command a higher display speed as a result; however, the response time for the
touch panel's operations will slow.
• Operation
Setup the GP to this option when using the GP mainly as an operation panel. As a
result, the GP will command better touch panel numeric input and switch response
times.
Leaving the GP in this mode does not influence the touch panel operation response
time of the rest of the GP's very much; however, the screen display renewal cycle will
slow down
• In a basic setup, run the same setup for all connected GP's.
• To increase the display speed, restrict addresses used to consecutive
addresses wherever possible. And make bit addresses consecutive to the
word unit.

Initialize
• Display Priority and Operation Priority Speed Difference

When using the Mitsubishi Electric Corp. A3A PLC, with a scan time of 20ms with
consecutive addresses (80 words not included in the System Area), the difference in
speed when reading is as shown in the following graphs.
Display Priority and Operation Priority Speed Difference
GP TOUCH MONOPOLIZE
The monopolizing of touch panel use can be set On or Off. When you want to
use the PLC exclusively with a Momentary operation setup on the touch panel
( Software PLC Connection Manual), 4.5 "About PLC Monopo-
lize", turn GP TOUCH MONOPOLIZE on.
When this setup is on, the touch panel uses the PLC exclusively whenever the
momentary operation setup on the panel is pressed. In this way, you can use the
inching operation with a momentary switch. When you stop pressing the panel,
exclusive use ends.
MONOPOLIZE TIME (0~2550s)

This field controls the length of time for the monopolize procedure when no
other touch panel operations are performed. The Monopolize process begins
when the System Data Area's 7th bit of word address LS14 turns on, and ends
either when the bit turns off, or when the time set here passes.
• Pressing the touch panel in the middle of the monopolize process

interrupts the MONOPOLIZE TIME function, ending exclusive use.
• When MONOPOLIZE TIME is set to 0, the monopolize function does
not end automatically.
For more about the contents of System Data Area LS6 (status) and LS14 (con-
trol) Software PLC Connection Manual, "Contents and Range of
System Area (Direct Access Communication)" and "Contents and Range of
System Data Area (Memory Link Communication)".

Initialize
5.6 INITIALIZE MEMORY

This command erases all the GP screen data.
• You cannot cancel the Initialization procedure after pressing the Start key.
• Initialization does not erase the SYSTEM SET UP, the SIO protocol,
nor the internal clock setups.
To initialize the GP internal memory, enter the common password 1101, or the
password entered in the SYSTEM SET UP screen. For more information abount
How to Input Number Chapter 4, "Input Number"
Initialization takes 10 to 20 seconds.
5.7 SET UP TIME
Set up the internal timepiece of the GP. Make date and time corrections in the
TIME SET UP fields.
The time—displayed on the screen using the Time Display function—

is not completely accurate. At room temperature, the GP internal clock
has an accuracy of +/- 40 seconds/month. The surrounding tempera-
ture and age of the unit can decrease the accuracy to +65 ~ -350 sec-
onds/month. However, the screen Time displays only up to the minute.

Initialize
5.8 SET UP SCREEN

The initial screen display upon powering up, the alarm character size, and other
related items are setup here.
INITIAL SCREEN NO.

Set up the screen file number that will first display upon powering up. If the BIN
option for DATA TYPE OF SCREEN NO in SYSTEM SET UP had been selected,
enter a number between 1~8999. Or, if BCD was the option set up, then input
a number between 1~1999.
ALARM MESSAGE
Set up the size of the letters of the ALARM MESSAGE.
1
Height=1; Width=1
2
Height=2; Width=2
4
Height=4; Width=4
16×8 pixels 32×16 pixels 64×32 pixels
ON-LINE ERROR DISPLAY

Set up whether or not error messages display during RUN mode.

Initialize
5.9 FONT SETTING
FONT SETTING
Select the character font used by the GP during RUN mode. ASCII, Korea,
Taiwan, China, and Japan are the font character options available.
KANJI FONT QUALITY

When the kanji character quality is set to HIGH, larger than full sized 2×2 mul-
tiplied characters display as 32 dot characters. When STANDARD is selected,
the display becomes a multiplied 16 dot font .
• This setting is only applicable when the FONT SETTING is JAPAN.

• When set to the HIGH quality setting, the Level 1 JIS Kanji Code
standard is the object. Level 2 standard characters, no matter what the
setting, display as 16 dots.

Initialize
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
MEMO
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901

Chapter 6
12345678901234567890123
12345678901234567890123
12345678901234567890123
RUN 12345678901234567890123
and Errors
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
1. RUN
12345678901234567890123
12345678901234567890123
2. Troubleshooting
12345678901234567890123
12345678901234567890123
3. SELF-DIAGNOSIS
12345678901234567890123
12345678901234567890123
12345678901234567890123
This chapter describes the GP RUN and problem solving processes.
6.1 RUN
There are two ways of entering RUN mode, from powering up and from Off-line mode.
1. Powering Up
Activate the GP unit. After the unit has powered up, the START TIME value—set
up in INITIALIZE/ SYSTEM SET UP—determines how long the display, illustrated
below, appears, until it gives way to the screen number setup in the INITIALIZE/
SET UP SCREEN menu. However, if a screen has not been set up, then the
display below will remain.
GP System Version
Memory Upload is not possible for GP System Versions 1.20 and higher.
2. Off-line Mode
Press Off-line mode's MAIN MENU item number 4, RUN. The INITIALIZE/ SET
UP SCREEN option determines the first screen that appears in RUN mode, thereby
beginning communication with the PLC. However, if a screen has not been set
up, then the display above remains.

Run & Errors
Press the top left corner within 10 seconds of starting RUN to enter
Off-line Mode.
E.g. After powering up, the initial Screen is equipped with a Switch in
the top left corner. If this Switch is pressed within 10 seconds, it changes
the GP status from RUN mode to Off-line mode.
6.2 Troubleshooting
This section describes how to find and resolve problems that may occur on the
GP. If there is a problem on the PLC side, refer to the corresponding PLC
manual.
1. Troubles
Shown below are some problems that may occur while using this unit.
(1) No Display
The screen will not display even when the unit is powered On. Also, during
RUN mode, the screen disappears.
(2) No Communication
The GP unit cannot extract data from the host. An error message may ap-
pear on the screen as a result. For more about error messages, refer to the
section in this chapter titled, "Error Messages".
(3) Touch Panels Do Not Function

The touch panel does not react when pressed, or the reaction time is very
slow.
(4) Off-line displays During RUN Mode.
For the first three problems, see the flowcharts listed on the following pages.
For the last problem, a SYSTEM ERROR may have developed while displaying
the Off-line mode screen. Refer to Chapter 6.4, "Error Messages—Details".

Run & Errors
However, this is not a problem when having entered Off-line mode by pressing
the top left corner within ten seconds of powering up.
Before Operating
• Because of the danger of electric shocks, make sure the power is
not supplied before wiring the unit.
• When changing the backlight, there is the danger of electric
shocks and burns, so be sure to use gloves when working on the unit.
This section assumes that the cause of any problems comes from the
GP, and not from the host. When the host PLC is the problem, refer to
the corresponding PLC manual.

Run & Errors
2. No Display
Follow the flowchart below when the screen does not display when powering
up, or the screen turns Off by itself during RUN mode, to find an appropriate
solution.
No Screen Display
Has data transferred NO Transfer screen data from the

from the Screen screen editing software.
editor?
Chapter 4.5, "Transfer
Screen Data".
YES
YES Does the power lamp

turn On?
NO
Is it using the correct NO Plug in the power cable properly.

power voltage? Chapter 2, "Specifica-
tions".
YES
Turn Off the power.
Disconnect the
power cable.
Fix the connection of the power ca-

Is the powercable connected NO
ble. Chapter 3, "Instal-
properly to this unit? lation and Wiring".
YES
YES Turn Off the power and reconnect

Does turning on the the communication cable.
power cause a display?

Run & Errors
Again, does turning the

power On cause a display? YES
YES Complete
Does the backlight
NOup?
(CFL) light NO
Is the communication cable YES

connected properly to this
unit?
NO
Connect the cable properly.

Chapter 3, "Installation and Wiring" and
the Software PLC Connection Manual.
Possible problems with the PLC. Check

if the PLC is working properly.
Has the backlight (CFL) NO Correctly setup the backlight (CFL)

in the GP. 7-3 "Chang-
been setup correctly?
ing the Backlight" in this manual.
NO
Go to Off-line mode.*1
(Press the upper left cor-
ner of the screen)
NO Does the Off-line

menu display?
YES

Run & Errors
See if INITIALIZE/ Set up the correct Screen file

NO
SCREEN SET UP is OK. number. Chapter
5, "Initialize".
YES
Erase the data that has been writ-
ten. When using Direct Access, the
Has Off data been written YES address is +9; when using Memory
to the SYSTEM DATA Link, the address is +12. For more
AREA? o n t h e SYSTEM DATA AREA
Software PLC Connec-
NO tion Manual.
Run SELF-DIAGNOSIS' YES Internal FEPROM Data has altered.

INTERNAL FEPROM Initialize FEPROM, transfer the
CHECK*2. Is it OK? data, and try using again.
NO
There is a problem with the GP
unit. Please contact your lo-
cal GP distributor.
*1 To make the Off-line screen appear, turn the power Off, then back On, and press the
upper left corner of the screen within 10 seconds.
*2 When you run the FEPROM CHECK in SELF-DIAGNOSIS, all the screen data gets erased.
Be sure to make a backup of all the screens.

Run & Errors
3. Would Not Communicate
When the GP will not communicate with the host PLC, follow the flowchart
below to discover the origin of the problem and find a suitable response.
Or, if an error message displays on the screen, check the error code—
Error Message section in this chapter—to find the appropriate solution.
Does not communicate
Turn Off the power switch.
Has the correct PLC NO Setup the Table file that corresponds
protocol (Table file)
been selected? with the connected PLC.
Software Operation Manual.
YES
Attach the SIO cable unit properly,

Is the SIO cable at- NO making sure all connections are
tached properly to this secure. Software PLC
unit? Connection Manual.
YES
Setup the Termination Resistor in the
Is the Termination NO correct position with the correct val-
ues.
Resistor setup correctly?
Resistor position and values change
with each PLC type. When using
the Direct Access format,
YES
Software PLC Con-
nection Manual.
Disconnect all the cables except the For RS-422, use the solution provided
power cable and turn the unit On. in the dotted rectangle, above.

Run & Errors
Is the SELF-DIAGNOSIS/ YES Are the corresponding NO

SIO CHECK OK? SIO INITIALIZE settings
OK?
NO YES
Enter correct settings
and values.
Chapter 5,
"Initialize".
Is the Tag setup NO

correct?
YES
Check the tag data, and
correct the setup val-
ues.
Software
Tag Reference
Manual.
cal GP distributor.
Possible problems with the
PLC. Check if the PLC is
working properly.
• To run SELF-DIAGNOSIS's SIO CHECK options, special tools become

necessary.
For details about SELF-DIAGNOSIS, refer to the SELF-DIAGNOSIS sec-
tion in this chapter.

Run & Errors
4. The Touch Panel Does Not Work
When the touch panel does not react, or its reaction time is very slow after it is
pressed, please follow the flowchart below to find the origin of the problem,
and the appropriate solution.
Touch panel not working
In the INITIALIZE/ SET UP TOUCH

Is INITIALIZE's SET NO PANEL option, enter values applica-
UP TOUCH PANEL ble to the Touch Operation Mode.
correct? Chapter 5, "Initialize".
YES
Disconnect all but the Power

cable.
Are the setting for

Run SELF-DIAGNOSIS/ YES
TOUCH PANEL CHECK to touch input tag, or for
see if it is OK. parts connect? NO
NO YES
Set the addresses
within the allow-
able range, or rede-
fine the touch area.
cal GP distributor.

Run & Errors
6.3 SELF-DIAGNOSIS
The GP unit is equipped to check its own System and Interface for any prob-
lems. Use it to help diagnose any problems.
1. SELF-DIAGNOSIS Item List
• DISPLAY PATTERN
Displays all the figures and tiling patterns to check if they are correct.
• TOUCH PANEL
Checks the touch panel squares.
• FEPROM CHECKSUM
Runs the GP internal memory's (FEPROM) system and protocol checksum.
• FRAME BUFFER
Checks the GP internal display memory (FRAME BUFFER).
• *TOOL CONNECTOR
Checks the control lines and input/output lines for the tool connector.
• INPUT PORT (for Digital's maintenance use only)

Runs a check on the Input Port.
• *SIO CHECK
Checks the input/output lines for the RS-232C and RS-422 terminals.
The SELF-DIAGNOSIS items marked with an asterisk (*) require spe-

cial tools. Please prepare the required tool for each test.

Run & Errors
2. SELF-DIAGNOSIS—Details Of Each Item
This section explains the contents of SELF-DIAGNOSIS. For information about

how to operate the Screen, Chapter 4, "Off-line Mode"; for informa-
tion about how to set up the Special Tools, Chapter 3, "Installation
and Wiring".
DISPLAY PATTERN
Acts as a check of the screen drawing function(s). It is used, for example, when
the GP unit’s buzzer does not sound, or if the device’s contents do not display
correctly. Performing this check displays various screen patterns, and a “Dis-
play ON/OFF Check” is performed. During the “Display ON/OFF check”, the
screen, together with the buzzer, turns ON and OFF.
After the check is completed, if the unit performs normally, “OK” is displayed.
If a problem is discovered, “NG” is displayed.
TOUCH PANEL
Touch Panel check. Checks if each touch cell highlights when pressed.
INTERNAL FEPROM CHECKSUM (System & Protocol)

The Internal FEPROM System and Protocol check searches for any problems
that may arise during operations.
When the FEPROM is normal, OK displays; if there is a problem, an error mes-
sage appears. This check does not erase the System or Protocol.
FRAME BUFFER
The Frame Buffer (display memory) Check looks for any display problems that
may develop. When everything is normal, OK displays; when there is a prob-
lem, an error message displays.
TOOL CONNECTOR LOOP BACK

Use the Tool Connector Control line and Send/Receive line check when the GP
cannot send and receive data from the PC. To run the check, connecting a Tool
Connector Check Loop Back Cable (Dsub25 pin female connection) mounted
to the Downloading Cable (provided in your software package) is necessary.
See diagram next page.

Run & Errors
TOOL CONNECTOR LOOP BACK CABLE
When everything is normal, OK displays; when there is a problem, an error

message displays.
INPUT PORT
Used by Digital for maintenance purpose.
SIO CHECK
Checks the RS-232C and RS-422 I/O lines for areas where correspondence
problems develop. In the menu, select which check to run. To run the check, a
serial interface cable connection becomes necessary. If all is normal, OK dis-
plays; if there is a problem, an error message appears.
The Serial Interface cable wiring for each check is as shown below.
• DTR CHECK
Connect the DTR Loop Back cable to the GP's serial interface. If all is normal,
OK displays; if there is a problem, an error message appears.
• RTS CHECK
Connect the RTS Loop Back cable to the GP's serial interface. If all is normal,
OK displays; if there is a problem, an error message appears.

Run & Errors
• RS-422 CHECK
Connect the RS-422 Loop Back cable to the GP's serial interace. If all is nor-
mal, OK displays; if there is a problem, an error message appears.

Run & Errors
6.4 Error Message

This section explains the messages that appear when an error has occurred in the
GP unit during RUN mode. The origin of the problem behind each error message is
explained with appropriate ways of disposing of the error.
After a problem has been solved, turn the power Off, then On, and restart the GP.
1. Error Message List
The error messages listed below appear on the GP unit. Instructions on how to
find and solve error messages are explained on the following pages.
• SYSTEM ERROR
• ILLEGAL ADDRESS IN SCREEN DATA
• UNSUPPORTED TAG IN SCREEN DATA
• PLC NOT CONNECTED (02:FF) and (02:F7)
• PLC NOT RESPONDING (02:FE)
• RECEIVE DATA ERROR (02:FD)
• PLC COM. ERROR
• SCREEN MEMORY DATA IS CORRUPT
• CLOCK SETUP ERROR
• SCREEN TRANSFER ERROR
• SCREEN TAG LIMIT EXCEEDED
• OBJ. PLC HAS NOT BEEN SETUP
• GP STATION NO. DUPLICATION ERROR (02:F9) n:1

• NETWORK ADDRESS ERROR (02:F8) n:1
If there is more than one error, the GP displays the error message for
the last error detected.

Run & Errors
2. Error Messages—Details
SYSTEM ERROR
Indicates a fault in the basic operations of the GP.
Following the error message, an error code, as shown, will appear. Report the
error number, and details on how the error developed, to your local GP distribu-
tor.
• SYSTEM ERROR ( 03 : x x )
Displays when a PC transferred file cannot be rebuilt.
03 : x x
Error No.
Constant Value
• SYSTEM ERROR ( x x x : x x x : x x x )
Displays in RUN mode when a file cannot be rebuilt.
xxx : xxx : xxx
Error No. 3
Error No. 2
Error No. 1
• Offline mode displays while in RUN mode

When the GP changes to Off-line mode without pressing the screen, there is a
possibility that the screen data has been damaged. When the screen data is
damaged, after the SYSTEM ERROR displays, the screen automatically reverts
to Off-line mode after about 10 seconds. Run the INITIALIZE MEMORY com-
mand and transfer the GP screen data again from your PC.
ILLEGAL ADDRESS IN SCREEN DATA

This error message is caused by an overlap of addresses.
Following the error message, error codes, as listed below, appear. If the error
cannot be fixed, please report the error code and details on how the error devel-
oped to your local GP distributor.
ILLEGAL ADDRESS IN SCREEN DATA ( 0 0 B : x x x : x x x )

Error No. 2
Error No. 1
See the Table next page

Run & Errors
Overlapping Addresses
Error 1 Error 2 Contents
*1
191 All or part of the T-File or S-tag address range
overlap the addresses of System Data Area.
0C1 192
193
194 All or part of the System Data Area address,
A-File,*1or S-tag address range overlap the
0C2 195 addresses setup in a T-File
196
197 All or part of the T-File,*1or the S-tag or K-tag
address range overlap the address range set in
0C3 198 an A-File.
199
*1
All or part of the T-File, or the S-tag or K-tag
0C9 19B address range overlap the address range set in
an A-File.
Overlapping addresses, other than the ones mentioned above, can also
cause the Illegal Address message.
E.g. When the starting address of the System Data Area is set to
100, and the tag below is setup:
Tag Name/ Word Tag Format
Part ID No. Address
N1 99 BCD32
The N-tag is set to 32 bits, meaning it uses two word addresses. Since the
first address is 99, the second address must be 100. Address 100 is ineli-
gible for use since it has already been used for the System Data Area.
UNSUPPORTED TAG IN SCREEN DATA

A list of tag(s) in use that are unsupported by the current GP version appear
with this error message. Setup the tags to correspond with the GP.
For details about tags, Software Tag Reference Manual.
PLC NOT CONNECTED (02:FF) (02:F7)

Displays when communication with the PLC has stopped for over 60 seconds,
when there is a transmission timeout error, or when there is excess noise.
Check the correspondence cable wiring and connect correctly.
*1 For details about the T-File (trend graph) and A-File (alarm messages), refer to the Soft-
ware Tag Reference Manual.

Run & Errors
PLC NOT RESPONDING (02:FE)

Displays when there is a Reply Timeout Error, or when there is excess noise.
The origin of the problem and the matching solutions are listed in the table
below.
ORIGIN SOLUTION
1. The power for the PLC host is not 1. Turn On the host's power switch.
activated. 2. Setup the unit correctly and match up
2. GP unit INITIALIZE setup (Setup I/O, with the current host and Communication
PLC Setting) is incorrect. Cable.
3. The host and GP powering up 3. Turn the host's power On first, wait 2~3
process was incorrect. seconds, then power up the GP unit.
4. The Communication Cable was not 4. Check the Communication Cable wiring
connected properly. and connect it up properly.
RECEIVE DATA ERROR (02:FD)

This problem arises as a result of one of these three:
• There is a problem in trying to receive the data
• The connected PLC and the PLC setup for the data is different
• Noise
These errors, except for noise, appear when the Communication Cable is pulled
out when the GP unit is On, or when normal communication operations are
being run, but the GP has been powered Off, then back On. To solve the prob-
lem, simply begin running transmissions again.
When the error is a result of noise, correct any improper connections.
GP STATION NO. DUPLICATION ERROR (02:F9) n:1

This error appears for one of two reasons:
• The GP number is same as the station number for another GP. Check all
the GP station numbers.
• In the middle of correspondences, the PLC power has been turned On/Off.
Reset the power on the PLC and GP.
NETWORK ADDRESS ERROR (02:F8) n:1

The SIO address setup for the GP is different from other GP's. Check the ad-
dress setup for all the GP's.

Run & Errors
PLC COM. ERROR

Appears when the address setup for tags exceeds the address range on the host
side. Check the Error Number that appears and use the following table to eradi-
cate the problem.
PLC COM. ERROR ( 02 : x x )
Error code (see the table below)
Constant Value
Error # Origin Solution

(MtoM type) There is a data format Check the data being transferred on the
FC
problem with the message received. host side.
The address set on a tag, the address * When using Memory to Memory Type:
used for storing data for Trend Graph, or Set the addresses within the set range of
the address registered with an alarm the System Area (0~2047), then send the
message is out of a set range. (address corrected information.
FB range error)
* Memory to Memory type. * When using Siemens' Series PLC Type:
* Siemen's PLC Series Set up the data block in the PLC where the
System Data area is.
Address range error Set the addresses within the allowable
FA
device range.
When using a Matsushita Electronics Decrease the number of screen tags.

PLC, and too many tags are used on the
53
screen, the PLC cannot receive any
data.
The tag address, Trend graph data Setup the addresses in a device range that
storage address, Alarm message exists.
51 Registry address, and the like, do not
exist in the PLC's internal memory.
(In the case of Fuji Electric PLC)
Others When the Error Number displays, different for each PLC, look up the error number in
the indicated PLC manual or, report the error number to the PLC maker.
• Disregard the above table if Error Number 51 appears and you are
using a PLC other than Fuji Electric. Look up the error contents in
your PLC manual and follow the instructions therein.
• Disregard the above table if Error Number 53 appears and you are
using a PLC other than Matsushita Electronics. Look up the error
contents in your PLC manual and follow the instructions therein.
• In Hitachi's HIDIC H (HIZAC H) Series, the error code is divided
into 2 bytes, whereas the GP Error Number is composed of 1 byte
codes. (see next page)

Run & Errors
E.g. Reply Return Display

Command Code Error No.
When the displayed error number is 8*, or 5*, use only the left column
as the error number.
• In Toshiba's PROSEC T Series, the Error Code is 4 places long; on
the GP, Error Numbers are displayed and changed into Hexadecimal.
E.g.
• With the Allen-Bradley PLC-5 and SLC-500 Series, the EXT/STS
error codes have been re-mapped to start at D0 HEX, so they will not
conflict with other error codes. When looking up the error number in
the PLC manual, subtract D0 h from the GP error code to get its error
value.
E.g. GP Error Code PLC Error Code
D1 —> 01
EA —> 1A
SCREEN MEMORY DATA IS CORRUPT

Displays when the checksum of the screen memory data does not match be-
cause of a corruption in the screen files.
Error codes, as shown below, follow the error message. By referring to the error
code, check the screens that have errors. When a screen file has been corrupted,
delete that file, and make a new one (or recall a backup copy if available).
SCREEN MEMORY DATA IS CORRUPT ( x x x x : x x x x )
The Screen Number that has an error. The number of screens that
(Displays only one per Screen Number.) have errors (Decimal)
CLOCK SET UP ERROR

This message displays when the backup battery for the internal clock is dead.
If the battery is incorrectly replaced, the battery may explode. To avoid the
danger, please do not replace the battery yourself. When the battery needs a
replacement, please consult with your local GP distributor.
After changing the backup battery, set up the internal clock. Chap-
ter 5, "Initialize".
The life span of the backup battery depends on the ambient tempera-
ture and the amount of current being charged and used. The table
below gives a general indication of how long the battery will last.

Run & Errors
Battery o Between Between

Temperature under 40 C 40~ 50o C 50~ 60o C
Expected
over 10 yrs. over 4.1 yrs. over 1.5 yrs
Life Span
SCREEN TRANSFER ERROR

Displays when an error occurs in the data transmission from the screen editor to
the GP panel. Try re-transmitting the screen data.
SCREEN TAG LIMIT EXCEEDED <MAX256>

When tags are setup beyond the tag limit, these tags are made invalid. Tags are
invalidated from the end tag, in the opposite order in which they were regis-
tered. Plus, when tags involve registered Windows and loaded screens, they are
invalidated in this order: Window Registry, Load Screen. Further details for
when multiple displays are set to one screen:
1. Invalidate registered windows from the end screen.
2. Invalidate loaded screens from the end screen.
Check invalidated tags and reduce the tag number.
OBJ. PLC HAS NOT BEEN SETUP (02:F9)

The host PLC setup in Software's Screen does not match the PLC in use. Use
the Error Code that follows the error message to select the proper PLC type in
the GP and correct the INITIALIZE setup.
OBJ. PLC HAS NOT BEEN SETUP ( x x )
The PLC number (Hexadecimal)

written onto the System File
See the Table, next page.

Run & Errors
PLC Number indicated by error code
PLC# PLC TYPE PLC# PLC TYPE
0 SYSMAC C 20 SIEMENS S5 135-115

SIEMENS S5 3964(R)
1 MELSEC-AnN (Link) 21
protocol
2 NEW SATELLITE JW 22 Allen-Bradly PLC-5
3 FACTORY ACE 28 Allen-Bradly SLC500
4 MICREX-F 63 FACTORY ACE 1:n
6 TOYOPUC-PC2 66 GE FANUC 90SNP
7 MEWNET-FP 67 HIZAC EC
8 HIDIC-S10 α 68 IDIC 1
9 Memocon-SC 69 IDIC 2
B MELSEC AnA (Link) 6A IDIC 3
D SYSMAC CV 6B FANUC Power Mate
E PROSEC EX2000 6C MICRO3
10 HIZAC H 81 MELSEC-AnN (CPU)
11 MELSEC-FX 8B MELSEC-AnA (CPU)
12 MELSEC-F2 0C KOSTAC SR21/22
14 KOSTAC SG8 6D KEYENCE
15 PROSEC T 1C MELSEC QnA (Link)
MEMORY LINK
4D 6F FLEX-PC (CPU)
(SIO Type)
18 FLEX-PC 1D MELSEC-QnA (CPU)
1B TC200 6E SELMART
1F SIEMENS S5 90-115

Run & Errors
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
MEMO
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901
1234567890123456789012345678901212345678901

Chapter 7
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
Maintenance
12345678901234567890123
12345678901234567890123
12345678901234567890123
12345678901234567890123
1. Regular Cleaning
12345678901234567890123
12345678901234567890123
2. Periodic Checkup
12345678901234567890123
12345678901234567890123
3. Changing the Backlight
12345678901234567890123
12345678901234567890123
12345678901234567890123
7.1 Regular Cleaning
Cleaning the Display

When the surface or the frame of the display gets dirty, soak a soft cloth in water
with a neutral detergent, wring the cloth tightly, and wipe the display.
• Do not use paint thinner, organic solvents, or a strong acid com-

pound to clean the unit.
• Do not press the touch-screen panel with hard or pointed objects,
such as a mechanical pencil, for it may damage the surface.
Rubber Gasket Replacement

The rubber gasket protects the GP and improves its water resistance. For in-
structions on installing the gasket, Chapter 3.1 "Installation".
A rubber gasket, which has been used for a long period of time, may have
scratches or dirt on it, and could have lost much of its water resistance.
Change the gasket periodically (or when scratches or dirt become visible).
Chapter 1.3 "Optional Equipment"

Maintenance
7.2 Periodic Check-Up

To maintain your unit in its best condition, please check your unit periodically.
Inspection Items:
Surrounding Environment
Is the temperature within the allowable range? (0~50o Celsius)
Is the humidity within the specified range? (20~85%RH)
Is the atmosphere free of corrosive gas?
GP Temperature
When the GP unit is mounted into a panel, the surrounding temperature
refers to the temperature inside the cabinet.
Electrical Specifications
Is the input voltage appropriate? (DC20.4~27.6V)
Attachments
Is the cable connected properly? Not loose?
Are the mounting brackets holding the unit securely?
Are there many scratches or traces of dirt on the rubber gasket?

Maintenance
7.3 Changing the Backlight
• Whenever changing the Backlight, be sure the power has been

turned Off.
• When the unit is still On, high voltage runs through the Backlight
area—do not touch.
• When the unit is Hot, be sure to use gloves to prevent injury.
• When the power has just been turned Off, the unit and Backlight
are still very hot.
Please make sure you have the proper Backlight for the GP-370 model.
Model Backllght Model
GP370-LG**
GP370-BL00-MS
GP370-SC**
Change the Backlight following the steps below.Be sure to use gloves.
Turn off the power supplied to GP.
Remove the power cable.( A )
Use a screwdriver to unscrew the two screws on the unit’s top face. (See figure
B ) Then, while holding the face of the GP with one hand, press down with
the thumb of your other hand on the center of the top face to unlock the top
face’s clip. This should allow the GP’s case to pivot open.
Disconnect the connector. (See figure C ) At this time, do not remove the
inner face’s protective metal plate.
Move the hook towards the right, and pull out the backlight.( D )
Insert a new Backlight, and put the connector back on.
At the bottom part of GP, insert the clips to the holes, put the rear cover
back in place and fasten the screws. In this step, be careful not to get any of
the Connector wiring caught between the front and the rear covers.( E )

Maintenance
A B C Connector
Power cable
Clip
Internal cover
C D Hook Backlight E

Index
Symbols Error Messages
CLOCK SET UP ERROR ............................... 6-19
1:1 ................................................................ 5-1, 5-13 GP STATION NO. REPEATED ..................... 6-17
ILLEGAL ADDRESS IN SCREEN DATA .... 6-15
A INCORRECT STORAGE INFORMATION AD-
DRESS ......................................................... 6-17
Alarm Display ....................................................... 5-3
OBJ. PLC HAS NOT BEEN SETUP ............. 6-20
PLC COM. ERROR ........................................ 6-18
B PLC NOT CONNECTED ............................... 6-16
Backlight ............................................................... 7-3 PLC NOT RESPONDING .............................. 6-17
Backlight Bulb ....................................................... 1-4 RECEIVE DATA ERROR .............................. 6-17
SCREEN MEMORY DATA IS CORRUPT ... 6-19
Bar Code Reader ................................................... 1-3
SCREEN TRANSFER ERROR ...................... 6-20
SYSTEM ERROR ........................................... 6-15
C UNSUPPORTED TAG IN SCREEN DATA .. 6-16
Cable ESC Key ................................................................ 4-6
Connection ........................................................ 1-2
Downloading Cable ................................... 1-3, 4-7 F
Mitsubishi PLC Procon I/F ............................... 1-3
Mitsubishi Programming Port I/F ..................... 1-5 FORCE RESET .......................................... 5-10–5-11
Multi-link ........................................................... 1-5 Force Reset ............................................................ 4-2
RS-232C .................................................... 1-3, 1-5 FRAME BUFFER ............................................... 6-10
RS-422 ....................................................... 1-3, 1-5
Siemen's Programming Port I/F Connection Cable G
1-5
Global Window ..................................................... 5-5
CCU ..................................................................... 5-14
GLOBAL WINDOW SETUP
Change Screen ....................................................... 5-3
DATA FORMAT ............................................... 5-6
COMMUNICATION SETUP GLOBAL WINDOW ........................................ 5-5
RECEIVE TIMEOUT ..................................... 5-12 GLOBAL WINDOW ACCESS ........................ 5-5
RETRY COUNT ............................................. 5-12 REGISTRATION NO. (1-256) ......................... 5-6
Connection Part ................................................... 5-15 Graphic Panel
Cover Sheet ........................................................... 1-4 Auxilary Input/Output ....................................... 2-6
CUSTOMIZE SETUP Caution .................................................................. v
GP TOUCH MONOPOLIZE .......................... 5-18 Cleaning ...................................................... 7-1–7-2
MONOPOLIZE TIME .................................... 5-18 Clock .................................................................. 2-4
PLC PRIORITY .............................................. 5-17 Display ............................................................... 2-6
Display Functions .............................................. 2-3
D Electrical Specifications ................................... 7-2
Environment ...................................................... 7-2
Data Device Storage Order ................................... 5-7 GP-470 External Dimensions ........................... 2-7
DISPLAY PATTERN .......................................... 6-10 Installation Brackets ......................................... 2-8
Downloading Cable ............................................... 4-7 Installation Dimensions .................................... 2-9
Interface ............................................................ 2-4
E Maintenance ...................................................... 7-1
Names and Functions of parts .......................... 2-6
Environmental Shield ............................................ 7-1 Package Contents ................................................ ix
Equipment. See Optional Equipment; System Structure Periodic Check-Up ............................................ 7-2
GP-370 Series User's Manual I

Index
Power Input Terminal Block ............................. 2-6 P

Screen Memory ................................................. 2-4
Serial Interface .................................................. 2-6 PLC PRIORITY
Temperature ...................................................... 7-2 Display Priority and Operation Priority Speed Diff
Tool Connector .................................................. 2-6 5-17
Touch Panel ....................................................... 2-6 PLC SETUP ........................................................ 5-13
Ventilation ......................................................... 3-2 CUSTOMIZE SETUP ..................................... 5-17
SET UP OPERATION SURROUNDINGS (n:1) ..
H ..................................................................... 5-14
SET UP OPERATION SURROUNDINGS (1:1) ...
Hitachi ..................................................................... 5-13
HIDIC-S10 alpha Series .................................. 5-13 STATION SETUP ........................................... 5-15
Power Terminal Block .......................................... 3-5
I
Power-up Sequence ............................................... 5-3
INITIALIZE .................................................. 4-3, 5-1 Printer .................................................................... 1-3
Standard Operations ................................... 4-4–4-5 Program Port ......................................................... 1-2
INITIALIZE MEMORY ..................................... 5-19
INPUT PORT ..................................................... 6-10 R
Installation ............................................................. 3-1 RS-232C ........................................................ 2-5, 4-7
Installation Brackets ............................................. 1-4 RS-232C Port ........................................................ 1-2
RS-422 ................................................................... 2-5
K
RS-422 Connector ................................................. 1-3
K-tag ...................................................................... 5-8 RS-422 Port ........................................................... 1-2
Rubber Gasket ............................................... 1-4, 7-1
L RUN ....................................................................... 4-3
Local Window ....................................................... 5-5
S
M SCREEN DATA TRANSFER ............................... 4-3
Main Menu ............................................................ 4-3 Screen Saver Function .......................................... 5-3
Matsushita Electric SELF-DIAGNOSIS ..................................... 4-3, 6-10
NEWNET-FP .................................................. 5-14 DISPLAY PATTERN ...................................... 6-11
Memory Loader ..................................................... 1-3 FRAME BUFFER ........................................... 6-11
Mitsubishi PLC A-Series INPUT PORT .................................................. 6-12
2 Port Adapter ................................................... 1-3 INTERNAL FEPROM CHECKSUM ............. 6-11
Procon I/F Cable ............................................... 1-3 KEYBOARD LOOP BACK ........................... 6-11
SIO CHECK .................................................... 6-12
Mitsubishi PLC FX-Series
DTR CHECK .............................................. 6-12
Procon I/F Cable ............................................... 1-3
RS-422 CHECK .......................................... 6-13
RTS CHECK ............................................... 6-12
N Standard Operations ................................... 4-5–4-7
n:1 ............................................ 5-1, 5-14, 5-15–5-16 TOUCH PANEL .............................................. 6-11
NETWORK INFORMATION ADDRESS ......... 5-15 Serial Interface ..................................... 1-2, 1-5, 2-5
Notes on UL Application ....................................... vii SET Key ................................................................ 4-6
SET UP I/O ........................................................... 5-9
O COMMUNICATION SETUP ......................... 5-12
SET UP SIO ...................................................... 5-9
Off-line Mode ................................................ 4-1, 6-1 SET UP TOUCH PANEL ............................... 5-10
Optional Equipment .............................................. 1-5 SET UP OPERATION SURROUNDINGS
II GP-370 Series User's Manual

Index
STARTING ADDRESS OF SYSTEM DATA AREA T

........................................................... 5-13, 5-14
SYSTEM AREA--READING AREA SIZE ........... Termination Resistor ............................................. 6-7
........................................................... 5-13, 5-15 TOOL CONNECTOR ......................................... 6-10
UNIT NO. .............................................. 5-13, 5-14 Tool Connector .............................................. 1-2, 3-7
SET UP SCREEN ............................................... 5-20 TOUCH PANEL .................................................. 6-10
ALARM MESSAGE ....................................... 5-20 Touch Screen ......................................................... 5-3
FONT SETTING ............................................. 5-21 Touch Screen Cover .............................................. 7-1
INITIAL SCREEN NO. .................................. 5-20
Transfer Screen Data ..................................... 4-7–4-8
KANJI FONT QUALITY ............................... 5-21
ON-LINE ERROR DISPLAY ......................... 5-20 Troubleshooting ............................................ 6-2–6-3.
See also Error Messages
SET UP SIO .......................................................... 5-9
No Display ......................................................... 6-4
COMMUNICATION FORMAT ....................... 5-9
The Touch Panel Does Not Work ..................... 6-9
CONTROL ........................................................ 5-9
Would Not Communicate.................................. 6-7
DATA LENGTH ................................................ 5-9
PARITY ............................................................. 5-9
V
SET UP TIME ..................................................... 5-19
SET UP TOUCH PANEL Verification Part .................................................. 5-16
BRIGHTNESS ADJUSTMENT ..................... 5-11
CONTRAST ADJUSTMENT ........................ 5-11 W
FORCE RESET ............................................... 5-10
TOUCH OPERATION MODE ....................... 5-10 Wiring .................................................................... 3-5
SIO CHECK MENU ....................................... 6-10 Grounding .......................................................... 3-6
Input/Output Signal Lines ................................. 3-6
Specifications
Power Cable ...................................................... 3-5
Electrical............................................................ 2-1
Environmental ................................................... 2-2 Word Byte LH/HL Order ...................................... 5-7
Interface ............................................................ 2-5
Structural ........................................................... 2-3
STATION SETUP
NETWORK INFORMATION ADDRESS ..... 5-15
STATION NO. ................................................. 5-16
Storage Order. See Data Device Storage Order
Symbols .................................................................... x
SYSTEM AREA SETUP
System Area Size .............................................. 5-4
SYSTEM ENVIRONMENT SETUP ................... 5-3
CHARACTER STRING DATA SETUP .......... 5-6
GLOBAL WINDOW SETUP ........................... 5-5
SYSTEM AREA SETUP .................................. 5-4
SYSTEM SETUP .............................................. 5-3
SYSTEM SETUP
BUZZER TERMINAL OUTPUT ..................... 5-3
DATA TYPE OF SCREEN NO. ....................... 5-4
PASSWORD (0-9999) ...................................... 5-3
STAND-BY MODE TIME (0-255) .................. 5-3
START TIME (0-255) ....................................... 5-3
TOUCH BUZZER SOUND .............................. 5-3
System Structure ................................................... 1-2
GP-370 Series User's Manual III

Index
IV GP-370 Series User's Manual

Manual Gp370 Mm21b Eng

Uploaded by

Copyright:

Available Formats

Manual Gp370 Mm21b Eng

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Gp370 Mm21b Eng

Uploaded by

Copyright:

Available Formats

1234567890123456789012345678901212345678901234567890123456789012123456789012345

GP-370 Series refers to the following GP model numbers:

© Copyright March 1996, Digital Electronics Corporation

GP-370 Series User's Manual i

Chapter 3—Installation and Wiring

ii GP-370 Series User's Manual

Chapter 6—RUN and Errors

GP-370 Series User's Manual iii

iv GP-370 Series User's Manual

To Prevent From Damage:

GP-370 Series User's Manual v

vi GP-370 Series User's Manual

GP370-LG31-24V (UL Registration Model: 2780051-1)

GP-370 Series User's Manual vii

viii GP-370 Series User's Manual

• GP Unit • Handling Guide

• Installation Fasteners (4/set)

GP-370 Series User's Manual ix

Warns a situation that could seriously injure a person or lead to

Explains a situation that could injure a person ir damage materi-

Explains a situation that requires a moderate amount of caution.

GP Screen Represents the “GP-PRO/PB III” or “GP-PRO/PB III for

Indicates a word or phrase that may require additional explana-

n:1 n:1 (multi-link) connection setup.

x GP-370 Series User's Manual

1 Preparation Before using the GP, arrange the hardware and

3 Select GP type and PLC

4 Create Screen/ Run Screen Setup

GP-370 Series User's Manual 1-1

6 Initialize Following the specifications of the PLC host in

1.2 System Structure

GP Interface PLC Interface PC Interface

1-2 GP-370 Series User's Manual

Mitsubishi PLC A-Series

Mitsubishi PLC A-Series

Mitsubishi PLC FX-Series

GP-370 Series User's Manual 1-3

GP-370 Backlight Bulbs

GP-70 Series Installation Fasteners

*1 There are cases where only a limited PCs can be used.

1-4 GP-370 Series User's Manual

1.3 Optional Equipment

*1 Certain types of PLC's cannot be connected. Software PLC Connection

GP-370 Series User's Manual 1-5

1-6 GP-370 Series User's Manual

Isolation Above 20MOhm at DC500V

GP-370 Series User's Manual 2-1

Vibration Endurance 10 ~ 25 Hz (X,Y,Z directions 30 minutes 2G)

Noise voltage: 1000 Vp-p

Weight Under 900g (GP unit only)

Cooling System Natural air circulation

2-2 GP-370 Series User's Manual

2.2 Function and Performance

Display Color White, Black 8 colors (white, red, blue,

Back light CFL (under normal temperatures and humidity, lifespan =

Resolution 320 × 240 pixels

Display Area 115W × 86H (mm)

Attributes Blink/ Reverse Video

Contrast The Touch Panel has 8 levels of contrast adjustments available

Chinese: (GB2321-80 codes) simplified Chines fonts