Va702-1 SM

Service Manual
ViewSonic VA702-1
VA702b-1
Model No. VS10781
17” Color TFT LCD Display
(VA702-1_ VA702b-1_SM Rev. 1b Sep. 2006)

ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright © 2006 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number Description of Changes Editor
1a 10/20/05 Initial Release G. Han
1b 9/12/2006 Add 2 nd panel V7 & VA (updated RSPL, BOM) Jamie Chang
ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

i
TABLE OF CONTENTS
1. Precautions and Safety Notices 1

2. Specification 4
3. Front Panel Function Control Description 13
4. Circuit Description 18
5. Adjustment Procedure 29
6. Troubleshooting Flow Chart 35
7. Recommended Spare Parts List 42
8. Exploded Diagram and Exploded Parts List 47
9. Block Diagram 49
10. Schematic Diagrams 50
11. PCB Layout Diagrams 58

ii
1. Precautions and Safety Notices
1. SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However,
improper used or installation may cause damage to the monitor as well as to the user.
WARNINGS:
z This monitor should be operated only at the correct power sources indicated on the label on the rear of the
monitor. If you’re unsure of the power supply in you residence, consult your local dealer or Power
Company.
z Use only the special power adapter that comes with this monitor for power input.
z Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. Only the qualified
technician can repair it.
z Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric shock to
human bodies.
z Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
z Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable immediately
and consult your closed dealer.
z Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
z Do not place heavy objects on the monitor or power cord.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated for
higher voltage, wattage, etc. Before replacing any of these components read the parts list in this manual
carefully. The use of substitute replacement parts, which do not have the same safety characteristics as
specified in the parts list, may create shock, fire, or other hazards.
3. SERVICE NOTES
z When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
z Keep wires away from high voltage, high temperature components and sharp edges.
z Keep wires in their original position so as to reduce interference.
z Adjustment of this product please refers to the user’ manual.

1
4. Handling and Placing Methods
Correct Methods: Incorrect Methods:

Only touch the metal of the LCD panel or the front
Surface of the LCD panel is pressed by fingers and
cover of he monitor. Do not touch the surface of the
that may cause "Mura".
polarizer.
Taking out the monitor by grasping the LCD panel.

Take out the monitor with cushions.
That may cause "Mura".

2
Correct Methods: Incorrect Methods:
Placing the monitor on foreign objects, That could
Place the monitor on a clean and soft foam pad.
scratch the surface of the panel or cause "Mura".
The panel is placed facedown on the lap. That may

cause "Mura".

3
2. Specification
INTRODUCTION
FEATURES VA702/b
Size 17 “
Luminance (Typ) 300 cd/㎡
Contrast Ratio (Typ) 500:1
TFTLCD PANEL Colors (6 bits + 2 bits FRC) 16.2 M
Response Time (Typ) 12 ms
Viewing Angle (H/V) 140 ° / 125 °
Recommend resolution 1280x1024@60Hz
Size 17 “
nd Contrast Ratio (Typ) 500:1
2
Size 17 “
Contrast Ratio (Typ) 600:1
3rd
Analog (75ohms, 0.7/1.0 Vp-p) Yes
Input Signal
Digital No
Separate Sync Yes
Sync Compatibility Composite Sync No
Sync on Green No
PC Yes
Compatibility Power Mac Yes
TV Box (NextVision 6) Yes
Power Voltage AC 100-240V, 50/60Hz Yes
On Mode(Max / Typ) 36 W/ 35 W
Power Consumption
Off Mode (Max) ≦1 W
Tilt ( 20 ° - -5 °) Yes
Swivel No
Ergonomics
Pivot No
Height Adjust No
OSD Control [ 1 ] [▼] [▲] [ 2 ] [ ] Yes
Physical (W x H x D) 378 x 374 x 196 mm
Dimension
Package (W x H x D) 440 x 511 x 132 mm
Physical (Net Weight) 4.5 kg
Weight
Package (Gross Weight) 6.2 kg
Operating Condition Temperature (℉/℃) 32℉-104℉ / 0℃-40℃
Humidity (%) 10 % - 90 %
Temperature (℉/℃) -4℉-140℉ / -20℃-60℃
Storage Condition
Humidity (%) 5 % - 90 %
UL, cUL, FCC-B, CB, CE, ENERGY, NOM, TUV/GS, TUV ERGO
(covers ISO13406-2 & MPRII), TCO’03, GOST-R+20 ORIGINAL
Regulation
COPIES HYGIENIC, SASO, PCBC, VCCI, BSMI, CCC, (PSB), (C-
TICK), TUV-S, Green Mark, Energy Star, RoHS, WEEE

4
GENERAL specification
Test Resolution & Frequency 1280x1024 @ 60Hz

Test Image Size Full Size
Factory Default:
Contrast and Brightness Controls
Contrast = 70%, Brightness = 100%
VIDEO INTERFACE
Analog Input Connector DB-15 (Analog), refer the appendix A

Equal to twice the weight of the monitor for
Video Cable Strain Relief
five minutes
Video Cable Connector DB-15 Pin out Compliant DDC 1/2B
Video Signals Video RGB (Analog) - Separate
Video Impedance 75 Ohms (Analog)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals LVDS
DDC 1/2B Compliant with Revision 1.3
Sync Compatibility Separate Sync
Shall be compatible with all PC type
Video Compatibility computers, Macintosh computers, and after
market video cards
640 x 350, 640 x 480, 720 x 400 (640 x
Resolution Compatibility 400*), 800 x 600, 832 x 624, 1024 x 768,
1152 x 870, 1280 x 720, 1280 x 1024
Exclusions Not compatible with interlaced video

5
POWER SUPPLY
Internal Power Supply Part Number: ILIPI-004

Input Voltage Range 90 TO 264 VAC
Input Frequency Range 47.5 TO 63 HERTZ
Short Circuit Protection Output can be shorted without damage
Over Current Protection 2.4 A typical at 14.2 VDC
Leakage Current 3.5mA (Max) at 254VAC / 60Hz
Efficiency 80% typical at 115VAC Full Load
Fuse Internal and not user replaceable
Power Dissipation 35 Watts (typ)
Max Input AC Current 0.8 Arms @ 90VAC, 0.4 Arms @265VAC
INRUSH CURRENT (COLD START) 30 A @ 120VAC, 50 A (max) @ 220VAC
Shall start and function properly when
under full load, with all combinations of
Power Supply Cold Start
input voltage, input frequency, and
operating temperature
Shall be able to withstand an ANSI/IEEE
Power Supply Transient Immunity C62.41-1980 2000V 200 ampere ring wave
transient test with no damage
Shall be able to withstand 1.5 times
Power Supply Line Surge Immunity nominal line voltage for one cycle with no
damage
Shall be able to function properly, without
reset or visible screen artifacts, when ½
Power Supply Missing Cycle Immunity
cycle of AC power is randomly missing at
nominal input
The power supply shall not produce audible
noise that would be detectable by the user.
Audible shall be defined to be in compliance
Power Supply Acoustics
with ISO 7779 (DIN EN27779:1991) Noise
measurements of machines acoustics.
Power Switch noise shall not be considered
Separate 3-prong NEMA 5-15P type plug.
US Type Power Cable Length = 1.8m. Connects to display.
Color = Black
Schuko CEE7-7 type plug.
European Type Power Cable Length = 1.8m, Connects to display.
Color = Black
Separate 3-prong type plug.
CCC Type Power Cable Length = 1.8m. Connects to display.
Color = Black
Separate 2-prong NEMA 1-15P type plug.
PSE Type Power Cable Length = 1.8m. Connects to display.
Color = Black
Power Saving Operation(Method) VESA DPMS Signaling
On Mode < 36 W (max) / 35 W(typ)
Power Consumption
Off Mode< 1W
Recovery Time On Mode = N/A, Active Off < 3 sec

6
ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency

Horizontal Frequency 30 – 82 KHZ
Vertical Refresh Rate 50 – 85* HZ.
* WHEN THE RESOLUTION IS SET TO 1280 X 1024, THE
VERTICAL REFRESH RATE MAY BE UP TO 75 HZ; FOR ALL
OTHER RESOLUTIONS, THE VERTICAL REFRESH RATE MAY
BE UP TO 85HZ.
Maximum Pixel Clock 140 MHz
Sync Polarity Independent of sync polarity.
Timing Table
Item Timing Analog
1 640 x 350 @ 70Hz, 31.5kHz Yes
2 640 x 400 @ 60Hz, 31.5kHz Yes
3 640 x 400 @ 70Hz, 31.5kHz Yes
4 640 x 480 @ 50Hz, 24.7kHz Yes
5 640 x 480 @ 60Hz, 31.5kHz Yes
6 640 x 480 @ 67Hz, 35.0kHz Yes
7 640 x 480 @ 72Hz, 37.9kHz Yes
8 640 x 480 @ 75Hz, 37.5kHz Yes
9 640 x 480 @ 85Hz, 43.27kHz Yes
10 720 x 400 @ 70Hz, 31.5kHz Yes
11 800 x 600 @ 56Hz, 35.1kHz Yes
12 800 x 600 @ 60Hz, 37.9kHz Yes
13 800 x 600 @ 75Hz, 46.9kHz Yes
14 800 x 600 @ 72Hz, 48.1kHz Yes
15 800 x 600 @ 85Hz, 53.7kHz Yes
16 832 x 624 @ 75Hz, 49.7kHz Yes
17 1024 x 768 @ 60Hz, 48.4kHz Yes
18 1024 x 768 @ 70Hz, 56.5kHz Yes
19 1024 x 768 @ 72Hz, 58.1kHz Yes
20 1024 x 768 @ 75Hz, 60.0kHz Yes
21 1024 x 768 @ 85Hz, 68.67kHz Yes
22 1152 x 870 @ 75Hz, 68.7kHz Yes
23 1280 x 1024 @ 60Hz, 63.4kHz Yes
24 1280 x 1024 @ 75Hz, 79.97kHz Yes
25 1280x 720 @ 60Hz, 45kHz (HDTV) Yes
Primary Presets
1280x1024 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO
configuration
Changing Modes
● Maximum Mode Change Blank Time for image stability: 3 seconds (Max), excluding
“Auto Image Adjust” time.
● Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting
when execute “Auto Image Adjust”.
● The monitor needs to do “Auto Image Adjust” the first time when a new mode is
detected. (See section “0-Touch™ Function Actions”)

7
AUDIO INTERFACE (SPEAKER SPECIFICATION)
No Audio function
TFT LCD PANEL

Panel Characteristics:
1st Source Panel

Model number Innolux MT170EN01 V1
Type TN type with LVDS interface
Active Size 337.9 (H) x 270.3 (V)
Pixel Arrangement RGB Vertical Stripe
Pixel Pitch 0.264 mm
GLASS TREATMENT Anti Glare (Hard coating 3H)
# OF BACKLIGHTS 4 CCFL edge-light (2 top / 2 bottom)
BACKLIGHT LIFE 40,000 Hours (Min) / 50,000 (Typ)
Luminance (Center) –
Condition: 300 cd/m2 (Typ after 30 minute warm up)
CT = 6500K, Contrast = Max, Brightness = 250 cd/m2 (Min after 30 minute warm up)
Max
Brightness Uniformity (13 points) 0.8 (Typ), 0.75(Min)
δ = Min Luminance of 13 points/Max Luminance
of 13 points
Contrast Ratio 500:1 (Typ), 400:1 (min)
Color Depth 16.2 million colors (6 bits + 2 bits FRC)
Viewing Angle (Horizontal) @ CR>=10 @ CR>= 5
Typical: 140º Typical: 160º
Minimum: 130º Minimum: 150º
VIEWING ANGLE (VERTICAL) @ CR>=10 @ CR>= 5
Minimum: 120º Minimum: 150º
Response Time 12 ms (Tr= 3 ms, Tf = 9 ms) (typ)
10%-90% @ Ta=25°C 16 ms (Tr= 5 ms, Tf = 11 ms)(max)
Panel Defects Please see Panel Quality Specifications.

8
2nd Source Panel

Active Size 337.9 (H) x 270.3 (V)
Luminance (Center) – 300 cd/m2 (Typ after 30 minute warm up)
Condition: 250 cd/m2 (Min after 30 minute warm up)
CT = 6500K, Contrast = Max,
Brightness = Max
δ = Min Luminance of 13 points/Max
Luminance of 13 points
@ CR>=10
Typical: 150º
Viewing Angle (Horizontal)
@ CR>= 5
Typical: 170º
@ CR>=10
Typical: 135º
VIEWING ANGLE (VERTICAL)
@ CR>= 5
Typical: 155º


9
3rd Source PAnel
Active Size 337.9 (H) x 270.3 (V)
Luminance (Center) – 280 cd/m2 (Typ after 30 minute warm up)
Condition: 250 cd/m2 (Min after 30 minute warm up)
CT = 6500K, Contrast = Max,
Brightness = Max
δ = Min Luminance of 13 points/Max
Luminance of 13 points
Viewing Angle (Horizontal) @ CR>=10 @ CR>=10
Minimum: 130º
@ CR>= 5
Typical: 170º
VIEWING ANGLE (VERTICAL) @ CR>=10 @ CR>=10

Minimum: 120º
@ CR>= 5
Typical: 155º


10
IMAGE PERFORMANCE
Factory Defaults
Item Defaults Item Defaults
Contrast 70% OSD H. Position 50%
Brightness 100% OSD V. Position 50%
Color Temperature 6500K OSD Time Out 15 Sec
Sharpness 33% OSD Background On
720x400/640x400 720x400 Resolution Notice Enabled
Luminance
Lv (Max) – Same as the Luminance in section
Condition: 4-7 “TFT LCD PANEL”
Contrast = 100%
Brightness = 100%
Color Temperature = 6500K
Lv (Def) –
Condition:
Contrast = Default Lv (Def) / Lv (Max) x 100% ≧ 85%
Brightness = Default
Color Temperature = 6500K
Display Size
Horizontal Display Size, Primary Preset Full Screen
Vertical Display Size, Primary Preset Full Screen
Saturation
Contrast = Default
Brightness = Default No visible saturation
Test Pattern = 32-Gray
Contrast = 100%
Brightness = 100% 6 – 8 level saturation (Max)
Test Pattern = 32-Gray
Preset Color Temperatures

SRGB It should meet IEC 61966-2-1 (1999-10) standard
Preset 1 9300K Wx= 0.283 +/- 0.02,
CCT (Max) = 10250K. Wy= 0.298 +/- 0.02
CCT (Min) = 8500K
Preset 2 6500K (Primary) Wx= 0.313 +/- 0.02
CCT (Max) = 6950K Wy= 0.329 +/- 0.02
CCT (Min) = 6100K
Preset 3 5400K Wx= 0.335 +/- 0.02
CCT (Max) = 5915K Wy= 0.350 +/- 0.02
CCT (Min) = 4935K
Preset Color Temperature Each color preset shall be adjustable. Red, Green,
Adjustability and Blue shall be individually controlled.

11
MECHANICAL
Dimension (Desktop)
Width 378mm (14.9 inch)
Height 374 mm (14.7 inch)
Depth 196 mm ( 7.7 inch)
Monitor Weight 4.5 Kg (9.9 lbs)
*Refer to Figure 1
Dimension (Head Only / Wall Mount) – Unfolding the Monitor Stand
Width 378 mm (14.9 inch)
Height 424 mm (16.7 inch)
Depth 61 mm (2.38 inch)
Monitor Weight 4.5 Kg (9.9 lbs)
*Refer to Figure 1
Ergonomics
Tilt Up From 0º up to ≧20º
Tilt Down From 0º down to -3º ~ -5 º
Cabinet Material
Display Head Plastic Material ABS UL94-HB
Neck/Base Plastic Material ABS UL94-HB
All internal plastic cabinet components shall be
Internal Plastic Cabinet Components
in compliance with the requirements of TCO’03
The reference for the bezel is the silver color
Front Bezel Color (VA702) and the midnight gray color (VA702b)
chip provided by ViewSonic
The reference for the bezel is the black color
(VA702) and the midnight gray color
(VA702b) chip provided by ViewSonic.
Neck, Base, and Rear Cover Color
The color difference between any two cabinet
components shall be less than 0.80 “Delta E”, in
the 1976 CIE L*a*b Colorspace.
The rear logo is silver color with the black color
background (VA702) and midnight gray color
Rear logo color
and background (VA702b) chip provided by
ViewSonic
The color drift due to UV-Light shall be less than
3.0 “Delta E” in the 1976 CIE L*a*b colorspace.
Cabinet Color Drift Due To UV-Light
Testing shall be performed according to the
requirements of ASTM Test Method D4459-93.
Cabinet Texture Mold-Tech # 11010 used on all external textured
surfaces.
The supplier shall submit textured color chips,
Samples plastic material specifications, and Material
Safety Data Sheets for approval.

12
3. Front Panel Function Control Description
Adjusting the Screen Image

Use the buttons on the front control panel to display and adjust the OSD controls which display
on the screen. The OSD controls are explained at the top of the next page and are defined in
“Main Menu Controls” on page 10.
Main Menu
with OSD controls
Front Control Panel

shown below in detail
Displays the control screen Power light

for the highlighted control. Green = ON
Also toggles between two Orange = Power Saving
controls on some screens.
Also a shortcut to Auto Standby Power
Image Adjust. On/Off
Scrolls through
menu options and
adjusts the
Displays the displayed control.
Main Menu or Also a shortcut to
exits the display the
control screen Contrast
and saves adjustment control
adjustments. screen.

13
Do the following to adjust the display setting:
1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one shown
below appears.
The line at the bottom of the screen shows
the current functions of buttons 1 and 2:
Exit or select the Brightness control.
4. To adjust the setting, press the upSor downTbuttons.

5. To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:

• Adjust the computer's graphics card so that it outputs a 1280 x 1024 @ 60Hz video signal to
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics card's
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)

14
Main Menu Controls
Adjust the menu items shown below by using the upSand downTbuttons.
Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal
to eliminate waviness and distortion. Press the [2] button to execute Auto Image
Adjust.
NOTE: Auto Image Adjust works with most common video cards. If this
function does not work on your LCD display, then lower the video refresh rate
to 60 Hz and set the resolution to its pre-set value.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
sRGB - This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
9300K - Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K - Adds red to the screen image for warmer white and richer red.
5400K - Adds green to the screen image for a darker color.

15
Control Explanation
User Color - Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, pressSorT.
3. When all color adjustments are complete, press button [1] twice.
Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
the ViewSonic® website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution
is 1280 x 1024 and the refresh rate is 60 Hertz.
Manual Image Adjust
H./V. Position (Horizontal/Vertical Position) moves the screen image left or

right and up or down. Press button [2] to toggle between Horizontal and
Vertical. The Horizontal setting moves the screen image to the left or to the
right. The Vertical setting moves the screen image up and down.
H. Size (Horizontal Size) adjusts the width of the screen image.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try the Auto Adjust function before using the Fine Tune control.
Sharpness adjusts the clarity and focus of the screen image.

16
Control Explanation
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and
control screens.
Resolution Notice advises the optimal resolution to use.
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For example,
with a “15 second” setting, if a control is not pushed within 15 seconds, the
display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is
operating in a factory Preset Timing Mode listed in the Specifications of this
manual.

17
4. Circuit Description
Electronic Circuit Theory
1 Switching Mode Power Supply
1.1 AC Current Input Circuit
P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC input voltage
is from 90V to 264V. R820 and R821 joined between two inputting main circuit to prevent man from
shock. L801 is used to clear up low frequency wave. C801 and C806 are used to discharge the waves
that L801 produced. High frequency waves are damped by C801 and C806. D801 is a rectifier which
composed of 4 build-in diodes, it inverts AC to DC.
1.2 High Voltage to Low Voltage Control Circuit
C805 is used to smooth the wave from rectifier. IC802 is a highly integrated PWM controller, which
build-in a power MOSFET. When rectified DC high voltage is applied to the DRAIN pin during start-up,
the MOSFET is off initially, and the CONTROL pin capacitor is charged through a switched high
voltage current source connected internally between the DRAIN and CONTROL pins. When the
CONTROL pin voltage Vc reaches approximately 5.8V, the control circuitry is activated and the
soft-start begins. The soft-start circuit gradually increases the duty cycle of the MOSFET from zero to
the maximum value over approximately 10ms. If no external feedback/supply current is fed into the
CONTROL pin by the end of the soft-start, the high voltage current source is turned off and the
CONTROL pin will start discharging in response to the supply current drawn by the control circuitry.
Resistor R803, R807, R824 and R825 are for line over voltage shut-down (OVP) and line under-voltage
detection (UVP).Resistors R801, R805, R822, and R823 are for external current limit adjustment, and
used to reduce the current limit externally to a value close to the operating peak current of primary about
1.35A. The mean is power will protected when the primary current over about 1.35A.
When PWM is turned off, the main current flow will be consumed through D804 and ZD802, This will
prevent MOSFET which built-in IC802 from being damaged under large current impulse and voltage
spike.
D806 and C815 provide internal Auxiliary current to CONTROL pin during normal operation. In
addition, error amplifier and feedback current to the CONTROL pin are for duty cycle control.
1.3 DC_5V and DC_14V Output Circuit
For DC 5V, D805 is used to rectify the inducted current. R806 and C811 are used to store energy when
current is reversed. The parts including C812, C814, C822, C821, B801 and L803 are used to smooth
the current waves.
For DC 14V, D803 is used to rectify the inducted current. R802 and C802 are used to store energy when
current is reversed. The parts including C808, C810 and L802 are used to smooth the current waves.
1.4 Feedback and OVP Protect Circuit
Pin R of IC803 is supplied 2.5V stable voltage. It is connected to 5V and 14V output through R811,
R810 and R818. R811, R810 and R818 are output sampling resistor. When the sampling voltage more
than 2.5V or less than 2.5V, feedback current of IC802 will change, this can change the voltage from
transformer T801.
For 5VDC output OVP, ZD803 is a zener diode, when 5V output voltage becomes up to 5.6V, the zener
current cause R819 voltage become up to 0.7V, Q801 is triggered and OVP starts. For 12VDC output
OVP, ZD804 is a Zener Diode, when 14V output voltage becomes up to 16V, the zener current cause
R819 voltage become up to 0.7V, Q801 is triggered and OVP starts. The collector current of Q801 is
used to make build-in diode light. FB Current of IC802 will be changed; it can change the voltage from
T801.
Q802, R827, R828 and ZD801 make up of dummy loading circuit. For start-up sequence, during 5V
output take place high loading first, this dummy loading circuit operated to insure 14V not be increased.

18
2 Inverter circuit
2.1 Low voltage to high voltage circuit
12VDC supplies the power to IC501 through F501; the control signals that BRIGHTNESS and ON/OFF
come from I/F board. ON/OFF signal connect to pin8 of IC501 and makes IC501 enabled.
BRIGHTNESS is connected to pin7 of IC501 to adjust the panel luminance. R524, R529, C505 make
up of a delay-time circuit and R528, R523, R524 make up of a voltage divided circuit. C504 is used to
filter the high frequency noise. The operation frequency is determined by R522 and C529. For BURST
MODE, its dimming frequency is determined by R527 and C506. C502 is used for soft start and
compensation, C502, C528 are used to filter noise.
The output drives, including NDR4, NDRV2, PDRV3, PDRV1 (pins1, 3, 15, 16 respectively), generate a
square pulses to drive MOSFET U501, U502. And U501, U502 works as full-bridge topology, it is high
efficient, zero voltage switch.
During start up, VSEN (pin9) detects the voltage at the transformer secondary. When VSEN reaches
3.0V, the output voltage is regulated. If no current is detected for around 1.5 seconds, IC501 will shut
down.
The current flowing through CCFL is detected and regulated through sense resistor R509, R511. The
feedback voltage through R506, R507, and C508 connected to Pin11 (ISEN), and then compared with a
reference voltage (1.5V) via a current amplifier, resulting in PWM drive outputs to full-bridge switches.
2.2 Protection circuit
Over Voltage Protection: R501and R502 are connected in high voltage output connector, the divided AC
voltage is inverted DC voltage through D508, R505 and C507are used to rectify wave & dump noise.
Then the voltage signal reaches Pin9 VSEN of IC501, when the voltage changes, build-in PWM of
IC501 will adjust output voltage.
Open Lamp Protection: In normal operation, the resistors R510, R511, R512, R509 are sensed a high
level AC voltage, the AC signal IS1 invert DC voltage through D509, R515, C533, and the high level
DC voltage reaches the gate pin of Q502, similarly, the gate pin of Q503, Q504, Q505 has high level DC
voltage. So the gate pin of Q501 has a low level voltage, and the IC501 is normal operation. Once one
of signal IS1, IS2, IS3, and IS4 is low, the voltages of Q501 gate pin is high level, and make the voltage
of ISEN low level, the IC501 will shut down.
3 I/F Board Circuit

3.1 Power Input
+5V is from the power board and supply for U101(FS8860-18PJ)﹑U102(FS8860-33PJ)﹑
U105(MCU:W78E65P) and panel. +3.3V output is generated from +5V through C169 and C102
filtering, and U102 outputs. +3.3V is used for U104 (Scaler: TSU16AK). +1.8V output is generated
from +5V through C169, C105 and C102 filtering, and U101 outputs. +1.8V is also used for U104.
3.2 MCU (W78E65P)
VDD is +5V and its frequency of XTAL1 is 22.1184MHz. U105 #2 is defined as panel-enable. When
the I/O port is low, Q101 and Q102 are conducted. And then after C109 and C110 filtering, obtain the
voltage of VLCD, which will be connected to CN103. U105 #3 is defined as CCFL-enable. When the
I/O port is low, Q103 is pulled up and the backlights are on; When the I/O port is high, Q103 is
conducted and the backlights are off. U105 #4 is defined as DET-VGA, connected with CN102 #5.
U105 #14, #36, #37, #38, #39, #40, #41, #42, #43 are the communications with U104 (Scaler), which
are connected to #72, #31, #78, #77, #30, #70, #71, #69, #32 of Scaler. U105 #43 outputs reset signal to
U104 (Scaler).
U106 is EEPROM used for saving EDID data, which is connected by SCL and SDA pins with #16 and
#17 of MCU. Connect #12 to #26 of U105 for ISP.
3.3 Scaler (TSU16AK)
The frequency of XTAL2 is 14.318MHz. U104 #1, #102-#103, #106-#113, #118-#125, #128 output
LVDS digital data of 8 bit to panel control circuit through CN103. U104 #73 generates a PWM
waveform by regulating the duty to control the brightness of the backlights. U104 #30-#32, #69-#72,
#77-#78 are the communications with U105 (MCU) that are connected to #36-#43 of MCU. These
communications include HWRESET, CSZ/ALE, SCL/RDZ, SDA/WRZ, and AD0-AD3.
19
3.4 VGA Input
Signal R, G, B, SOG input through CN102 #1, #2, #3, and C115, C116, C117 and C118 filtering the
high frequency noise. Signal HSYNC and VSYNC input through CN102 #13 and #14, and C119, R119,
C120, R120 filtering. Then the analog signal enters U104, and then U104 deals with it internally. In
addition, TVS101, TVS102, TVS103 (the three are BAV99), TVS104, TVS105, TVS106, TVS107 (they
are constant voltage diode of 5V6) are ESD protector. Signal DDC-SCL inputs via CN102 #15, and then
passes through TVS107 for ESD protection, goes into EDID EEPROM IC U103. Signal DDC-SDA
inputs via CN102 #12, and then passes through TVS106 for ESD protection, goes into EDID EEPROM
IC U103. CN102 #5 is defined as cable detect pin, this detector realizes via R107 and U105 #4. The
PC-5V of U103 is supplied by PC via CN103 #9 with D103 for ESD protection, or supplied by Monitor
self via D104.U103 is an EEPROM IC, which is a kind of memory and used for saving EDID data.
3.5 Button Control
Button “Key-Power” is defined as power on/off, which is connected to U105 #24 through CN106 #4.
Button “Key-2” is defined as two functions of selecting and adjustment, which is connected to U105
#25 through CN106 #1.
Button “Key-Up” is defined as plus, which is connected to U105 #26 through CN106 #3.
Button “Key-Down” is defined as minus, which is connected to U105 #27 through CN106 #5.
Button “Key-1” is defined as two functions of menu and exit, which is connected to U105 #28 through
CN106 #2.
LED indicator on the front bezel is defined as follows:
a. When press button “Key-Power”, U105 #6 is pulled down and U105 #7 is pulled high, so Q104 is
conducted and the LED indicator is green.
b. When in power-saving mode, U105 #6 is pulled high and U105 #7 is pulled down, so Q105 is
conducted and the LED indicator is orange.
3. FACTORY PRESET TIMING TABLE
H-Freq. V-Freq. Dot Clock

Item Resolution
(KHz) (Hz) (MHz)
1 640 x 350 31.5kHz 70Hz 25.2
2 640 x 400 31.5kHz 60Hz 25.2
3 640 x 400 31.5kHz 70Hz 25.2
4 24.7kHz 50Hz 19.8
5 31.5kHz 60Hz 25.2
6 35.0kHz 67Hz 30.2
640 x 480
7 37.9kHz 72Hz, 31.5
8 37.5kHz 75Hz, 31.5
9 43.27kHz 85Hz 36.0
10 720 x 400 31.5kHz 70Hz 28.3
11 35.1kHz 56Hz 36.0
12 37.9kHz 60Hz 40.0
13 800 x 600 48.1kHz 72Hz 50.0
14 46.9kHz 75Hz 49.5
15 53.7kHz 85Hz 56.3
16 832 x 624 49.7kHz 75Hz 57.3
17 48.4kHz 60Hz 65.0
18 56.5kHz 70Hz 75.0
19 58.1kHz 72Hz 78.5
1024 x 768
20 60.0kHz 75Hz 78.8
21 68.67kHz 85Hz 94.5
22 1152 x 870 68.6kHz 75Hz 100
23 63.4kHz 60Hz 108
1280 x 1024
24 79.97kHz 75Hz 135
25 1280 x 720 45kHz 60Hz 74.2
20
4. Power On/Off Sequence
4.1 Hardware Power ON
When power cord is plugged into AC socket, SMPS starts work and provides U105 and U106 with
VCC5V. When VCPU inputs to U105, U105 resets circuit active, sets U105 all registers to preset modes,
and then U105 #43 sends out a HWRESET signal voltage to reset U104, and then monitor goes into
stand-by mode. That means hardware power on has been completed.
4.2 Software Power ON/OFF

When press power key, U105 #24 recieves low pulse, and sends out “Power on/off” order back to U104,
and then U104 will do the power on/off.
- If Power ON, U105 #6 (LED_Green) will send out High potential, and then LED green on.
- If Power OFF, U105 #7 (LED_Orange) will send out High potential, and then LED Orange on.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following sequency.
T1 (ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6 (ms) T7 (ms)

0.1~10 0~10 >200 >100 0~50 0.1~10 >1000
5. AC Outlet Pin Assignment
Pin Symbol Description

3
1 L Live
1 2 2 N Neutral
3 E GND
P801
6. Inner Connector Pin Assignment

6.1 CN501, CN502, CN503, CN504 (Connect to Panel Backlight, SM02B-BHSS-1-TB or equivalent)
Pin Symbol Description
1 H.V. High voltage for lamp
2 L.V. Low voltage for lamp
6.2 CN101 (Power BD to Interface BD)

Pin
Symbol Description
No.
1,2 +5V (VCC5V) +5.2V output
3,6 GND Ground

21
4 BRIGHTNESS Brightness Control
5 ON/OFF CCFL on/off Control
6.3 CN106 (Interface BD to Keypad)

Pin
Symbol Description
No.
1 KEY_SELECT/AUTO Select control and auto adjustment control
2 KEY_MENU/EXIT OSD page selection and exit
3 KEY_UP OSD “▲” control to adjust value to increase
4 KEY_POWER DC power on/off control
5 KEY_DOWN OSD “▼” control to adjust value to decrease
6 LED_GREEN Green LED lighting control
7 GND Ground
8 LED_ORANGE Orange LED lighting control
6.4 CN103 (Connect I/F BD to panel, FI-X30S-H or Equivalent)

Pin No. Symbol Function
1 RXO0- minus signal of odd channel 0(LVDS)
2 RXO0+ plus signal of odd channel 0(LVDS)
7 GND Ground
8 RXOC- minus signal of odd clock channel (LVDS)
9 RXOC+ plus signal of odd clock channel (LVDS)
12 RXE0- minus signal of even channel 0(LVDS)
13 RXE0+ plus signal of even channel 0(LVDS)
14 GND Ground
17 GND Ground
20 RXEC- minus signal of even clock channel (LVDS)
21 RXEC+ plus signal of even clock channel (LVDS)
24 GND Ground
25 GND Ground
26 GND Ground or Open
27 GND Ground
28 VCC Power supply (5.0 V)
6.5 CN102 (D-SUB Connector)
Pin Symbol Pin Symbol Pin Symbol

1 Red video input 6 Red GND 11 NC
2 Green video input 7 Green GND 12 Serial data (SDA)
3 Blue video input 8 Blue GND 13 H / H+V SYNC
22
4 NC 9 +5V(from PC) 14 VSYNC
5 Cable Detect 10 GND 15 Data clock line (SCL)
7. Key Parts Pin Assignment

7.1 IC802 (TOP246Y, Power Control IC)
Pin Symbol I/O Description
1 C I Control
2 L I Line Sense
3 X I External Current Limit
4 S O Source of MOSFET(GND)
5 F I Frequency
6 D I Drain of MOSFET
7.2 IC501 (OZ9910G, CCFL inverter controller IC)

Pin No. Symbol I/O Description
Bottom MOSFET gate drive output in dual forward
1 NDRV4 O
converter
2 PGND High-current power ground
Bottom MOSFET gate drive output in dual forward
3 NDRV2 O
converter
4 GNDA Low-current signal ground
5 CT I Timing capacitor of high frequency oscillator
6 LCT I Timing capacitor of set LPWM frequency
7 ADJ I Control command input –DC
8 ENA I Enable input
9 VSEN I Voltage sense feedback
10 CMP_SST I Soft start and loop compensation capacitor
11 ISEN I Current sense feedback
12 VREF O Reference voltage output
13 VIN I Supply voltage for IC
14 HSB I High side driver buffer output
15 PDRV3 O Top MOSFET gate drive output in dual forward converter
16 PDRV1 O Top MOSFET gate drive output in dual forward converter
7.3 U104 (TSU16AK)

1 LVBOM O B-Link Negative LVDS Differential Data
2 GND Ground
3 BYPASS For External Bypass Capacitor
4 NC Not connected
5 NC Not connected
6 BUSTYPE IN Low : Serial bus; High : Direct bus
7 NC Not connected
8 NC Not connected
9 NC Not connected
10 GND Ground
11 VDDP O Digital Output Power
12 NC Not connected
13 NC Not connected
14 NC Not connected
15 NC Not connected
16 NC Not connected
23
17 NC Not connected
18 VDDC I Digital Core Power
19 GND Ground
20 GND Ground
22 NC Not connected
23 NC Not connected
24 NC Not connected
25 NC Not connected
26 NC Not connected
27 NC Not connected
28 NC Not connected
29 NC Not connected
30 AD0 I/O DDR direct bus AD0; 4mA driving strength
32 HWRESET I Hardware reset; active high
33 XIN I Crystal Oscillator Input
34 XOUT O Crystal Oscillator Output
35 AVDD_MPLL MPLL Power
36 GND Ground
37 HSYNC0 I Analog HSYNC input
38 VSYNC0 I Analog VSYNC input
39 GND Ground
40 NC Not connected
41 NC Not connected
42 GND Ground
43 NC Not connected
44 NC Not connected
45 VDD_ADC I ADC Power
46 NC Not connected
47 NC Not connected
48 GND Ground
49 NC Not connected
50 NC Not connected
51 VDD_ADC I ADC Power
52 REXT External resistor 390 ohm to AVDD ADC
53 AVDD PLL I PLL Power
54 GND Ground
55 AVDD ADC I ADC Power
56 GND Ground
57 BINOM I Reference ground for analog blue input
58 BINO I Analog blue input
59 GINOM I Reference ground for analog green input
60 GINO I Analog green input
61 SOGIN0 I Sync-on-green input
62 RINOM I Reference ground for analog red input
63 RINO I Analog red input
64 GND Ground
65 AVDD_ADC I ADC Power
66 REFP Internal ADC top de-coupling pin
67 REFM Internal ADC bottom de-coupling pin
68 GND Ground
69 ALE/CS I DDR direct bus ALE; active high
70 WRZ/SDA I/O DDR direct bus WRZ; active low
71 RDZ/SCL I DDR direct bus RDZ; active low
72 INT O CPU interrupt; 4mA driving strength
73 PWM0 O PWM0; 4mA driving strength
74 PWM1 O PWM1; 4mA driving strength
75 NC Not connected
76 NC Not connected

24
79 NC Not connected
80 NC Not connected
81 NC Not connected
82 NC Not connected
83 NC Not connected
85 GND Ground
86 GND Ground
88 NC Not connected
89 NC Not connected
90 NC Not connected
91 NC Not connected
92 NC Not connected
93 NC Not connected
95 GND Ground
96 GND Ground
98 NC Not connected
99 NC Not connected
100 NC Not connected
101 NC Not connected
102 LVA3P O A-Link Positive LVDS Differential Data
103 LVA3M O A-Link Negative LVDS Differential Data
105 GND Ground
106 LVACKP O A-Link Positive LVDS Differential Clock
107 LVACKM O A-Link Negative LVDS Differential Clock
115 GND Ground
116 GND Ground
117 VDDC Digital Core Power
118 LVB3P O B-Link Positive LVDS Differential Data
119 LVB3M O B-Link Negative LVDS Differential Data
120 LVBCKP O B-Link Positive LVDS Differential Clock
121 LVBCKM O B-Link Negative LVDS Differential Clock
25
127 GND Ground
128 LVBOP O B-Link Positive LVDS Differential Data
7.4 U105 (Micro-controller: W78E65P-40)

1 P4.2/INT3 A bi-directional I/O port with alternate function.
2 P1,0/T2 O Enable panel power on
3 P1.1/T2EX O Enable CCFL work
4 P1.2 I VGA cable detection
5 P1.3/PWM0 O provide alternated function of PWM Volume
provide alternated function of PWM Green LED
6 P1.4/PWM1 O
lighting control
provide alternated function of PWM Orange LED
7 P1.5/PWM2 O
lighting control
8 P1.6/PWM3 Function is the same as that of standard 8052
9 P1.7/PWM4 Function is the same as that of standard 8052
10 RST I Reset control pin
11 P3.0/RXD SCL line of I2C for EDID, debug function
PORT 4: A bi-directional I/O port with alternate
12 P4.3/INT2
function.
13 P3.1/TXD SDA line of I2C for EDID, debug function
14 P3.2/INT0 I Interrupt request control pin
15 P3.3/INT1 O Shut Down Volume Mute standard 8052.
16 P3.4/T0 O SCL line of I2C communication with EEPROM
17 P3.5/T1 I/O SDA line of I2C communication with EEPROM
18 P3.6/WR I DVI cable detection standard 8052.
EEPROM write protection control for DVI EDID
19 P3.7/RD O
Prevent E2PROM Write in standard 8052.
20 XTAL2 Crystal 22.1184MHz In
21 XTAL1 Crystal 22.1184MHz out
22 GND Sink voltage ground
23 P4.0 A bi-directional I/O port with alternate function.
24 P2.0/A8 DC power on/off control
25 P2.1/A9 OSD “►” control to adjust value to increase
26 P2.2/A10 OSD “◄” control to adjust value to decrease
27 P2.3/A11 Selection of menu command listed
28 P2.4/A12 OSD page selection
29 P2.5/A13 Auto adjustment control
30 P2.6/A14 A bi-directional I/O port with internal pull-ups
31 P2.7/A15 A bi-directional I/O port with internal pull-ups
32 PSEN Program Store Enable
33 ALE Address Latch Enable
34 P4.1 A bi-directional I/O port with alternate function
External Access Enable external ROM. The ROM
address and data will not be presented on the bus if
35 EA I
the EA pin is high and the program counter is
within the 64 KB area.
36 P0.7/AD7 I/O DDR Direct Bus Communication with Scaler
40 P0.3/AD3 I/O WRZ line of DDR Direct Bus
41 P0.2/AD2 I/O RDZ line of DDR Direct Bus
42 P0.1/AD1 I/O ALE line of DDR Direct Bus
43 P0.0/AD0 O Hardware reset to Scaler
44 +5V I +5V for MCU working voltage

26
Disassembly Block
VA702/b (INL PANEL)DIS-ASSEMB LY BLOCK
BASE SUB-ASSM *1 BEZEL

HINGE COVER*2 SUB-ASSM(G/S) BUTTON FUNCTION KEY*1
(SCREW,P,CROSS,M5*22, Ni*4)
BEZEL SUB-ASSM *1 FRONT BEZEL (G/S)*1 LED LENS*1

(SCREW,B,CROSS,T4*10, BLK*4)
BACK COVER
SUB-ASS’Y SUPPORT VESA *1
HINGE,RIGHT*1
HINGE,LEFT*1
(SCREW,F,CROSS,T4*10, Ni*4) BACK COVER *1
(SCREW,I ,CROSS,M3*4,Zw*1)
Rubber spacer*1
Logo *1
BACK COVER SUB-ASS’Y*1
BASE COVER
PLATE BASE *1
BRACKET_R*1 SUB-ASS’Y
GROUND WIRE*1
KEYPAD CABEL*
KEYPAD ASSM*1 BASE COVER *1
(SCREW,PW,CROSS,M3*5, Ni *2)
(Ace tape*4)
INL PANEL*1
BRACKET_R*1
(SCREW,PW,CROSS,M3*5, Ni *2)
(Ace tape *2)
IF BOARD*1 CHASSIS*1
POWER BOARD*1
FFC CABLE*1
CLIP,WIRE*1 INSULATOR,MYLAR*1
(SCREW,PW,CROSS,M3*5, Ni*5)
(BOLT, #4-40x11.8, Ni*2)
Note: Arrows are disassembly directions.

27
Assembly Block
VA702/b (INL panel)ASSEMBLY BLOCK
CHASSIS*1 FRONT BEZEL (G/S)*1 LED LENS*1
LOGO PLATE,THREE BRID*1 BUTTON FUNCTION KEY*1

INSULATOR,MYLAR*1
LOGO PLATE BEZEL

“VIEWSONIC”*1 SUB-ASSM(G/S
IF BOARD*1
)
POWER BOARD*1
FFC CABLE*1
CLIP,WIRE*1 SUPPORT VESA *1
BACK COVER *1
(BOLT, #4-40x11.8, Ni*2)
LOGO PLATE(ELLIPSE)*1 BACK COVER
Rubber*1 SUB-ASS’Y
INL PANEL*1
BRACKET_L*1
(Ace tape*2)
BRACKET_R*1 PLATE BASE *1 BASE COVER *1

GROUND WIRE*1
KEYPAD CABEL*1
KEYPAD ASSM*1
BASE COVER
(SCREW,PW,CROSS,M3*5, Ni*2) RUBBER FOOT LE1708 *4
SUB-ASS’Y
(Ace tape*4)
BASE SUB-ASSM *1
BACK COVER SUB-ASS’Y*1 OPENING STAND LABEL*1
HINGE COVER*2
(SCREW,P,CROSS,M5*22, Ni*4)
HINGE,RIGHT*1
HINGE,LEFT*1
(SCREW,F,CROSS,T4*10, Ni*4) S/N LABEL*1
(SCREW,I ,CROSS,M3*4,Zw*1) QC LABEL*1
HI POT LABEL*1
BEZEL SUB-ASSM *1
ID LABEL*1
(SCREW,B,CROSS,T4*10, BLK*4) V17 LCD MONITOR
FINAL ASM(INL)
Note: Arrows are assembly directions.

28
5. Adjustment Procedure
1. Key Function Description
CONTROL
KEYS FUNCTION
KEY
[AUTO] [2] By pressing [AUTO] key, “Auto Image Adjust” is performed
[MENU] [1] By pressing [MENU] key, Main menu display

A. When “MENU OSD” display, press these keys to change the contents of an
adjustment item, or change an adjustment value
[▼] [▲] B. When “MENU OSD” is un-display, press these keys to change brightness
and contrast
[POWER] Power on or power off the monitor
2. Hot Key Operation

CONTROL
KEYS FUNCTION
KEY
Recall Contrast or Brightness while in the Contrast or Brightness
[▼] + [▲] adjustment, or recall both of Contrast and Brightness when the OSD is
not open.
[1] + [2] Toggle 720x400 and 640x400 mode when input 720x400 or 640x400 mode.
[1] + [▼] + White Balance (Not shown on user’s guide)

[▲]
[1] + [▼] Power Lock
[1] + [▲] OSD Lock
Remark : All the short cuts function are only available while OSD off
3. OSD Control
3.1 OSD table
Layer 1 Layer 2 Layer 3
Auto Image Adjust
Contrast (+ / -)
Contrast/Brightness
Brightness (+ / -)
Srgb
9300K
6500K
Color Adjust 5400K
Red (+ / -)
User Color Green (+ / -)
Blue (+ / -)
Information
Manual Image Adjust H Position (+ / -)
H/V Position
V Position (+ / -)
H Size +/-

29
Fine Tune +/-
Sharpness +/-
English
French
German
Italian
Language Select Spanish
Finnish
Japanese
Setup Menu
Simplified Chinese
Traditional Chinese
Resolution Notice On/Off
H Position (+ / -)
OSD Position
V Position (+ / -)
OSD Time Out
OSD Background On/Off
Memory Recall
3.2 OSD lock Menu function
OSD Lock Menu Function Check

Item Method Phenomenon
Press any of buttons"1", "▼",
Activate OSD lock [1] + [▲] 10S "▲", "2" will appear "OSD
Locked" 3s
Deactivate OSD lock: [1] + [▲] 10S(again)
NOTICE:
When the OSD is locked will lock all functions.
Status bar indicating OSD Lock or Unlock is in progress and when complete it will
indicate “OSD Locked”
OSD Lock should not lock Power Button and Power Lock function
3.3 Power lock Menu function

Power Lock Menu Function Check
Activate Power Lock Can not turn off the LCD;
Press the power button will
appear "Power Button Locked"
[1] + [▼] 10S OSD 3s;
LCD would automatically turn
back "On" when power is
restored after a power failure
Deactivate Power
[1] + [▼] 10S(again)
Lock
NOTICE:
Status bar indicating Power Button lock or unlock is in progress and when complete it will
indicate “Power Button Locked”
Power should only be lockable in the “On State”

30
3.4 Resolution notice function
Resolution Notice Menu

Resolution Notice OSD should
show on screen after changing to
Activate Resolution
non-native mode for 30 sec, ------
Notice Menu
And it should disappear after 10s
or by pushing button [1] or [2]
Deactivate
Push button [2] under Resolution
Resolution Notice -------
Notice OSD, select Disable
Menu
3.5 Factory Mode Introduction

When input the signal, press “power key” to turn off the monitor. Press” [▼] +[▲] +[ ] “at the
same time so as to enter factory mode. After power on, press ‘’Menu[1]’’ key, you can see the
Factory menu.
INL : Currently using panel model name

V2 050526 : Currently using firmware version information.
Auto Color : Automatically calibrate chip ADC parameter by using chip internal DAC
Color Temperature : The R, G, B of 9300K and 6500K and 5400K and User Mode
Colors are all generated from scaling back end.
4. Burn-in pattern
If it is a new monitor, and in factory mode, if no VGA signal input, Burn-in pattern will self
generate automatically. Burn in patterns are: full Red, Green, Blue, White and Black. You can not escape
from Burn-in pattern until plug in VGA Cable, and then press the power key. Turn the monitor off and
then turn it on.
5. Auto Color (Automatically calibrate chip ADC parameter by using chip internal
DAC)
If it is a new-built set and it is first time to do the “auto color”, please confirm the following steps:
-Connect the VGA cable with the standard video pattern generator and display 16-gray pattern on
the monitor.
- Press “Power” to power off the monitor.
- Press” [▼] +[▲] +[ ] “simultaneously to enter factory mode.
- Press ‘’Menu[1]’’, then press ‘’Auto[2]’’ to execute Auto color item.
- After the “Auto Color” process finished, please press “Power” to restart monitor.
6. EDID (Rewrite EDID data to EEPROM)

If we need to rewrite the EEPROM data, please confirm the following steps.
1. Plug in VGA Cable; we can rewrite the EDID data to EEPROM by using “EDID Rewrite”
program.
2. If the “EDID Rewrite” process finished, please pull out VGA cable and press ‘’2’’+’’▲’’ at the
same time.
3. Pull out AC power cable or press power key to restart.

31
7. Upload firmware to MCU via VGA Cable
7.1 Connect ISP board between monitor and PC as below configure
LCD Monitor
Service
D-Sub
cable
ISP Board
15PIN
D-SUB
RS232
Insert to
9PIN
RS232 9pin
15PIN
D-SUB
CON on PC PC
VGA
output
+12V Adapter Normal

shipping
cable
7.2 Before plug in the power cord, make sure keep “▲“ key to be pressed, when power on you can
enter ISP mode.
7.3 8051ispwriter.exe will detect automatically which MCU used in this monitor. Do it as the order
shown on the screen, choose the corresponding firmware version, and load to MCU.
7.4 After finish, please plug out power cable and re-start monitor again.
8 After repair, to ensure the quality you should do the following test and
adjustment
Item Content Equipment
1.Signal is set as 1280x1024@60Hz
Test OSD 2. LCM button are from left to right, checking whether each Chroma
function single function key and compound function key can be Signal Generator
worked.
1. Set input mode to 1280x1024@60Hz
2. Set Pattern to 32 gray shades Chroma
Contrast Check
3. Set contrast to the max. The brightest 5~6 shades brightness Signal Generator
cannot be distinguished.
1. Do “Auto color” at 1280 x 1024@60Hz, 32gray shades
2. Measure color temperature, check it complies with the
Chroma Signal
Color following temperature:
Generator and color
Temperature 5400K x=0.335 +/- 0.02, y=0.350 +/- 0.02
analyzer
6500K x=0.313 +/- 0.02, y=0.329 +/- 0.02
9300K x=0.283 +/- 0.02, y=0.298 +/- 0.02
1. Use Chroma Pattern Generator to make sequence.
VESA (640x480 800x600 1024x768 1280x1024), MAC
832x624 DOS (640x350 720x400), the detail supported
Modes switching Chroma Signal
modes and power saving signal.
check Generator
2. Confirm the above timing modes must be full screen and
the picture must be normal.
3. LED is Orange at power saving mode.

32
1. Set brightness to default value 100 and contrast to default
Chroma Signal
Y measurement value 70 at 6500K
Generator and Color
at default setting 2. At full white patter, Measure Y, which should be
Analyzer
250+/-10cd/m² (QDI 220+/- 10cd/m²)
1. Mode: 1280x1024@60Hz
2. Set Brightness& contrast to default value Equipment::
Panel Flicker
3. Do “Auto Image Adjust” Chroma Signal
check
4. Shut down PC to check whether there’s glitter on the center Generator & PC
of the picture.
1. Mode: 1280x1024@60Hz
2. Pattern: full white
3. Brightness: Max. Chroma signal
4. Contrast: Default generator and Power
5. Check power consumption at each modes meter
Power saving Power
State LED color AC input:
Consumption 230V/50Hz
Normal ＜38Ｗ Green
Stand By ＜1Ｗ Orange
Power Key Off ＜1Ｗ No

33
6. Troubleshooting Flow Chart
1. Common Acknowledge
z If you change the interface board, be sure that the U105, U106 and U103 these three components also
changed to the new I/F board because there was program inside. If not, please re-write EDID or upload
firmware into MCU via VGA Cable.
z If you adjust clock and phase, please do it at the condition of Windows shut down pattern.
z If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
z This LCM is analog interface. So if the entire screen is an abnormal color that means the problem happen
in the analog circuit part, if only some scale appears abnormal color that stand the problem happen in the
digital circuit part.
z If you check the H/V position, please use the crosshatch pattern.
z This LCM support more than 30 timing modes, if the input timing mode is out of specification, the picture
may appears abnormally.
z If brightness uneven, repairs Inverter circuit or change a new panel.
z If you find the vertical line or horizontal line lost on the screen, please change panel.

34
2. No Power & Power LED Off
No power
Check primary Check circuit Check IC802,

rectifier voltage if short C805, T801
Check F801, P801,

D801
Check pin3 of
IC802 voltage Check R801, R805,
about 1V R822, R823, R817
Check pin2 of IC802 Check R803, R807,

voltage about 2V R824, R825
Check pin1 of IC802 Check R812, R816,

voltage is 5.8V C818
END

35
3. DC output voltage is unstable
Output Voltage Unstable
Check Vbe of Check circuit if Check ZD801, ZD802,

Q801 below 0.3V short ZD803, D803, D805
Check Q801, Q802
Check reference Check pinR Check R809, R814,

voltage IC801, R818
of IC801
Check R810, R811
Check feedback Check Vpin3-4 of Check C815, D806,

IC801 about 6V R812
circuit
Check Vpin1-2 of
IC801 about 1V
Check R809,
R814
END

36
4. Output power is unstable
Unstable power
Check sampling Check R810,

Circuit R811, R818
Change R810, R811,

R818
Check the R pin Check the C pin

voltage of IC803 voltage of IC803 Change
about 2.5V if 3V IC803
Check R809, R808, R814,

D809
Check pin1 of
IC802 voltage Check D806, C815 if
is 5.8V short
Change
D806, C815
Check pin3 of
IC802 voltage Change R801, R805,
about 1V R822, R823, R817
END

37
5. Backlight can’t be turned on
No raster?
Yes
LED Green?
Yes
Backlight cannot be
turned on.
Yes
No
Is there 14Vdc voltage Check power
on pin13 of IC501? supply
Yes
No
Yes Check I/F
Is there high-level voltage Is R526 Ok? board
on pin8 of IC501?
No
Yes R526 open
Connecting the
No output connector
Check CN501,
CN502, CN503 and again
CN504?
Yes
No
Is there pulse waveform on Yes
pin1, pin3, pin15 and pin16 of Is Ok IC501? U501, U502 fail
IC501 at the moment of restart?
No
IC501 fail
Yes
No
T501, T502 fail
Is ok T501, T502?
Yes Check protected circuit Q501,

Q502, Q503, Q504 END

38
6. Black Screen and backlight turn on

39
7. White Screen
White Screen
OK
LVDS Cable Reinsert Workmanship
NG
OK
Change LVDS Cable LVDS Cable NG
NG
OK OK
Check VLCD is 5V Check LVDS signals Panel Fail
NG NG
Check Panel-Enable of Check the HWRESET of NG

Check RP101
U105(pin2) is low U104 exists
OK NG OK
Check Check the pins of

Q101,Q102,Q107,R103 U105
END

40
8. Bad Screen
Bad Screen
OK
LVDS Cable Reinsert Workmanship
NG
OK
Change LVDS Cable LVDS Cable NG
NG
NG 1.Check
Check Crystal:pin20,21 of X101,C154,C155
U105 and pin 33,34 of U104 2.Check
X102,C126,C168
OK
NG
Check ALE/RDZ/
Check the communication of
WRZ/AD0/AD1/AD2/
U104 and U105
AD3/HWRESET
OK
Check the pins of

U104 and U105

41
7. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VA702-1)
ViewSonic Model Number: VS10781
Rev: 1b
Serial No. Prefix: PST
Item Description ECR/ECN ViewSonic P/N Ref. P/N Location Universal number#
1 Accessories: KIT,ACCESSORY(INL), LE1709 A-00003039 703000000500
2 PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x A-00003040 453070800250
3 PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0. RoHS Added on 9/11/06 A-00005255 453070800170R
4 KIT,ACCESSORY,VA702-INL V7,LE1709 RoHS Added on 9/11/06 A-00005274 703000000506R
5 PC Board Assembly: PCBA,IF BOARD, LE1709-6A0 B-00003041 790411300600
6 PCBA,KEYPAD BOARD, LE1709 B-00003042 790411500000
7 PCBA,KEYPAD BOARD, LE1709 RoHS Added on 9/11/06 B-00005278 790411500000R
8 PCBA,PWR&INV./B, LE1709-6A0 B-00003043 790411400600
9 PCBA,PWR&INV./B, LE1709-6A0 RoHS Added on 9/11/06 B-00005279 790411400600R
10 PCBA,IF BOARD(V7), LE1709- 6A0 RoHS Added on 9/11/06 B-00008066 790411300630R
11 Cabinets: BASE, LE1709 C-00003044 501240201000
12 BEZEL,FRONT(SILVER),VA702, LE1709 C-00003045 501010202700
13 COVER,BACK, LE1709 C-00003046 501020202900
14 ASSY,BASE, LE1709 RoHS Added on 9/11/06 C-00005262 714020002400R
15 ASSY,BEZEL(S),LE1709,VA702 RoHS Added on 9/11/06 C-00005263 714030002400R
16 ASSY,BACK COVER, LE1709 RoHS Added on 9/11/06 C-00005264 714050002400R
17 COVER,HINGE, LE1709 RoHS Added on 9/11/06 C-00006088 501020203000R
18 Cables: CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 CB-00003047 453010100100
19 CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 RoHS Added on 9/11/06 CB-00005254 453010100100R
20 HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28 RoHS Added on 9/11/06 CB-00005259 430303000140R
21 HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B, RoHS Added on 9/11/06 CB-00005260 430300800320R
22 HRN ASS'Y 1P 137mm BLACK,UL100 7 #20, RoHS Added on 9/11/06 CB-00005261 430300100210R
23 Electronic LCD PANEL 17" MT170EN01-V1(INNOLUX) E-00003048 631102070270
24 Components: LCD PANEL 17" MT170EN01-V7-G1,AM17000057 RoHS Added on 9/11/06 E-00008006 631102071910R
25 LCD PANEL 17" MT170EN01-V7-G2,AM17000057 RoHS Added on 9/11/06 E-00008007 631102071920R
27 Hardware: SCREW,B,CROSS,T.T-4*10,BLK ,RoHS Added on 9/11/06 HW-00005265 509412610500R
28 SCREW,F,CROSS,T.T-4*10,Ni RoHS Added on 9/11/06 HW-00005266 509212610300R
29 SCREW,P,CROSS,M5*22,Ni,RoHS Added on 9/11/06 HW-00005267 509116822300R
30 SCREW,PW,CROSS,W/WAS,M3*5,NI RoHS Added on 9/11/06 HW-00005269 509146305300R
31 BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN. RoHS Added on 9/11/06 HW-00005270 509000000700R
32 SCREW,I,CROSS,M3*4,Zw,RoHS Added on 9/11/06 HW-00005271 509016304102R
33 HINGE,RIGHT, LE1709 RoHS Added on 9/11/06 HW-00005276 502060401910R
34 HINGE,LEFT, LE1709 RoHS Added on 9/11/06 HW-00005277 502060401900R
35 Packing Material: GENERIC FOAM SET Added on 9/11/06 P-00001347 30833
36 GENERIC BOX Added on 9/11/06 P-00002515 20653
37 BAG,PLASTIC,L550xW450xT0.05mm,LE1709 P-00003049 506120004300
38 CARTON,VA702, LE1709 P-00003050 506020006800
39 CARTON,VA702, LE1709 RoHS Added on 9/11/06 P-00005256 506020006800R
40 CUSHION,EPS-L, LE1709 P-00003051 506040005500
41 CUSHION,EPS-L, LE1709 RoHS Added on 9/11/06 P-00005257 506040005500R
42 CUSHION,EPS-R, LE1709 P-00003052 506040005510
43 CUSHION,EPS-R, LE1709 RoHS Added on 9/11/06 P-00005253 506040005510R
44 BAG,PE+EPE,L590xW480xT0.6mm (PRINTED)LE1 RoHS Added on 9/11/06 P-00005272 506120300400R
45 BAG,PLASTIC,l690xW(455+145)xT0.05mm, LE1 RoHS Added on 9/11/06 P-00005273 506120004500R
46 Plastics: RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708 PL-00003053 503020002600
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to
eliminate repeated cross checks of each item between this version and prior versions.

42
RECOMMENDED SPARE PARTS LIST (VA702B-1)
Rev: 1b
Serial No. Prefix: PSX
Item Description ECR/ECN ViewSonic P/N Ref. P/N Location Universal number#
1 Accessories: PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x A-00003040 453070800250
2 KIT,ACCESSORY,VA702B-INL,LE1709 A-00003054 703000000510
3 PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0. RoHS Added on 9/11/06 A-00005255 453070800170R
4 Board Assembly: PCBA,IF BOARD, LE1709-6A0 B-00003041 790411300600
5 PCBA,KEYPAD BOARD, LE1709 B-00003042 790411500000
6 PCBA,KEYPAD BOARD, LE1709 ROHS Added on 9/11/06 B-00005278 790411500000R
7 PCBA,PWR&INV./B, LE1709-6A0 B-00003043 790411400600
8 PCBA,PWR&INV./B, LE1709-6A0 ROHS Added on 9/11/06 B-00005279 790411400600R
9 PCBA,IF BOARD(V7), LE1709- 6A0 ROHS Added on 9/11/06 B-00008066 790411300630R
10 Cabinets: BASE, LE1709 C-00003044 501240201000
11 COVER,BACK, LE1709 C-00003046 501020202900
12 BEZEL,FRONT(GRAY),VA702b, LE1709 C-00003055 501010202710
13 ASSY,BASE, LE1709 RoHS Added on 9/11/06 C-00005262 714020002400R
14 ASSY,BACK COVER, LE1709 RoHS Added on 9/11/06 C-00005264 714050002400R
15 COVER,HINGE, LE1709 RoHS Added on 9/11/06 C-00006088 501020203000R
16 ASSY,BEZEL(G),LE1709,VA702b RoHS Added on 9/11/06 C-00008095 714030002410R
17 Cables: CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 CB-00003047 453010100100
18 CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 RoHS Added on 9/11/06 CB-00005254 453010100100R
19 HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28 RoHS Added on 9/11/06 CB-00005259 430303000140R
20 HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B, RoHS Added on 9/11/06 CB-00005260 430300800320R
21 HRN ASS'Y 1P 137mm BLACK,UL100 7 #20, RoHS Added on 9/11/06 CB-00005261 430300100210R
22 Electronic LCD PANEL 17" MT170EN01-V1(INNOLUX) E-00003048 631102070270
23 Components: LCD PANEL 17" MT170EN01-V7-G1,AM17000057 RoHS Added on 9/11/06 E-00008006 631102071910R
26 Hardware: SCREW,B,CROSS,T.T-4*10,BLK ,ROHS Added on 9/11/06 HW-00005265 509412610500R
27 SCREW,F,CROSS,T.T-4*10,Ni ROHS Added on 9/11/06 HW-00005266 509212610300R
28 SCREW,P,CROSS,M5*22,Ni,ROHS Added on 9/11/06 HW-00005267 509116822300R
29 SCREW,PW,CROSS,W/WAS,M3*5,NI RoHS Added on 9/11/06 HW-00005269 509146305300R
30 BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RoHS Added on 9/11/06 HW-00005270 509000000700R
31 SCREW,I,CROSS,M3*4,Zw,ROHS Added on 9/11/06 HW-00005271 509016304102R
32 HINGE,RIGHT, LE1709 RoHS Added on 9/11/06 HW-00005276 502060401910R
33 HINGE,LEFT, LE1709 RoHS Added on 9/11/06 HW-00005277 502060401900R
34 Packing Material: BAG,PLASTIC,L550xW450xT0.05mm,LE1709 P-00003049 506120004300
35 FOAM,EPS-L, LE1709 P-00003051 506040005500
36 FOAM,EPS-L, LE1709 RoHS Added on 9/11/06 P-00005257 506040005500R
37 FOAM,EPS-R, LE1709 P-00003052 506040005510
38 FOAM,EPS-R, LE1709 RoHS Added on 9/11/06 P-00005253 506040005510R
39 BOX,VA702B, LE1709 P-00003056 506020006810
40 BOX,VA702b, LE1709 RoHS Added on 9/11/06 P-00008079 506020006810R
41 BAG,PE+EPE,L590xW480xT0.6mm (PRINTED)LE1 RoHS Added on 9/11/06 P-00005272 506120300400R
42 BAG,PLASTIC,l690xW(455+145)xT0.05mm, LE1 RoHS Added on 9/11/06 P-00005273 506120004500R
43 GENERIC BOX Added on 9/11/06 P-00002515 20653
44 GENERIC FOAM SET Added on 9/11/06 P-00001347 30833
45 Plastics: RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708 PL-00003053 503020002600
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic
Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.

43
BOM LIST (VA702-1)
Serial No. Prefix: PST
Rev: 1b
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty (PC)
1 CB-00005261 430300100210R HRN ASS'Y 1P 137mm BLACK,UL1007 #20,RoHS 100
2 CB-00005260 430300800320R HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B, For VSI 1
3 CB-00005259 430303000140R HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28 For VSI 1
4 CB-00005254 453010100100R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 For VSI 1
5 A-00003675 453070800230R PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/ For V7 Panel For Singapore 1
6 A-00003671 453070800420R PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G For V7 Panel For Australia 1
7 A-00006733 453070800480R PWRCORD 7A/125V BLK 6FT CNS,VCTF 3Gx0.75 For V7 Panel For TWN 1
8 A-00006734 453070800500R PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx For V7 Panel For Korea 1
9 N/A 501010202700R BEZEL,FRONT(SILVER),VA702,LE1709 100
10 N/A 501020202900R COVER,BACK, LE1709 For VSI 1
11 C-00006088 501020203000R COVER,HINGE, LE1709 For VSI 2
12 N/A 501030201900R BUTTON,FUNCTION KEY, LE1709 For VSI 1
13 N/A 501120101200R LENS, LE1709 For VSI 1
14 N/A 501240201000R BASE, LE1709 For VSI 1
15 N/A 502020300700R BRACKET,LEFT, LE1709 For VSI 1
16 N/A 502020300710R BRACKET,RIGHT, LE1709 For VSI 1
17 HW-00005277 502060401900R HINGE,LEFT, LE1709 For VSI 1
18 HW-00005276 502060401910R HINGE,RIGHT, LE1709 For VSI 1
19 N/A 502080300300R SUPPORT,VESA, LE1709 ROHS 100
20 N/A 502090301300R CHASSIS, LE1709 For VSI 1
21 N/A 502170300400R PLATE,BASE,LE1709 For VSI 1
22 N/A 503010001700R RUBBER,SPACER,L25xW10xT4.0mm,LE1709 For VSI 1
23 N/A 503020002600R RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708 ROH 400
24 N/A 505040202000R INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L For VSI 1
25 N/A 505040203600R INSULATOR,PET,355x292x0.1mm, LE1709 100
26 P-00005256 506020006800R CARTON,VA702, LE1709 For VSI 1
27 N/A 506037003700R CARDBOARD,COVER,L1120xW980xH120xT5mm,LE1 For VSI 0.02778
28 N/A 506039001200R CORNER PAPER,820x50x50mm For VSI 0.0556
29 N/A 506039002301R CORNER PAPER,2050x50x50xT3mm,LE1709 ROHS 5.556
30 P-00005257 506040005500R CUSHION,EPS-L, LE1709 For VSI 1
31 P-00005253 506040005510R CUSHION,EPS-R, LE1709 For VSI 1
32 N/A 506102000300R LOGO PLATE,VIEWSONIC, LE1709 For VSI 1
33 N/A 506102000400R LOGO PLATE,VIEWSONIC, LE1709(THREE BIRDS For VSI 1
34 N/A 506102000500R LOGO PLATE,VIEWSONIC, LE1709(ELLIPSE) For VSI 1
35 P-00005272 506120300400R BAG,PE+EPE,L590xW480xT0.6mm(PRINTED)LE19 100
36 N/A 506150001310R PALLET,1120x980x120mm.LE1709 ROHS 1.389
37 N/A 506250005102R LBL,AGENCY(VA702), LE1709(KOREA MARK) For VSI 1
38 N/A 506380001800R TAPE,WRAPPING TYPE,48mmx50M ROHS LE1915 1.2
39 N/A 506380002100R TAPE,WRAPPING TYPE(VIEWSONIC),50mmx75M,L For VSI 0.00513ROL
40 N/A 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm),LE1709 ROH 0.1
41 N/A 506390000400R LABEL,OPENING STAND, LE1709 For VSI 1
42 N/A 506390000600R LABEL,HI-POT PASS, LE1709 For VSI 1
43 N/A 506390210110R LABEL,CARTON(8ms),PRC, LE1709 For V7 Panel For VSI 1
44 N/A 506390400100R LABEL,PRODUCT(2), LE1709 For VSI 1
45 N/A 506390500100R LABEL,ENERGY STAR, LE1709 For VSI 1
46 N/A 506431000300R FILM,PE 500mmx900M ROHS 0.05
47 N/A 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) For VSI 1
48 N/A 506440002400R LABEL,BLANK,50x25mm,LE1709(S/N) For VSI 1
49 N/A 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) For VSI 0.02778
50 N/A 506440003000R LABEL,BLANK,35x8mm, LE1709 ROHS For V7 Panel For VSI 2
51 HW-00005270 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO For VSI 2
52 HW-00005271 509016304102R SCREW,I,CROSS,M3*4,Zw,ROHS 100
53 HW-00005267 509116822300R SCREW,P,CROSS,M5*22,Ni,ROHS For VSI 4
54 HW-00005269 509146305300R SCREW,PW,CROSS,W/WAS,M3*5,NI For VSI 9
55 HW-00005266 509212610300R SCREW,F,CROSS,T.T-4*10,Ni ROHS For VSI 4
56 HW-00005265 509412610500R SCREW,B,CROSS,T.T-4*10,BLK ,ROHS For VSI 4
57 N/A 511100001500R CLIP,WIRE.CH-01P(PG), LE1709 For VSI 1
58 E-00008006 631102071910R LCD PANEL 17" MT170EN01-V7-G1,AM17000057 For VSI 1
61 N/A 703000000500R KIT,ACCESSORY,VA702-INL,LE1709 For VSI 1
62 C-00005262 714020002400R ASSY,BASE, LE1709 For VSI 1
63 C-00005263 714030002400R ASSY,BEZEL(S),LE1709 For VSI 1
64 C-00005264 714050002400R ASSY,BACK COVER, LE1709 For VSI 1
65 N/A 71407276B100R ASSY,FIANL(S,V7/G1&2&3),LE1709-6A0 For VSI 1
66 N/A 71408276B100R ASSY,PANEL(V7/G1&2&3),LE1709-6A0 For VSI 1
67 B-00008066 790411300630R PCBA,IF BOARD(V7), LE1709- 6A0 ROHS For VSI 1
68 B-00005279 790411400600R PCBA,PWR&INV./B, LE1709-6A0 ROHS For VSI 1
69 B-00005278 790411500000R PCBA,KEYPAD BOARD, LE1709 ROHS For VSI 1

44
BOM LIST (VA702B-1)
Serial No. Prefix: PSX
Rev: 1b
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty (PC)
1 CB-00005261 430300100210R HRN ASS'Y 1P 137mm BLACK,UL100 7 #20,RoHS For VSI&VSA 1
2 CB-00005260 430300800320R HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B, For VSI&VSA 1
3 CB-00005259 430303000140R HRN LVDS FFC 30P 234mm,RoHSACCX30234KU28 For VSI&VSA 1
4 CB-00005254 453010100100R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE,SZ40 For VSI&VSA 1
5 A-00003675 453070800230R PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/ For Singapore 1
6 A-00006679 453070800250R PWR CORD 10A/125V BLK 6FT UL/CSA,SVT 18x For VSA 1
7 A-00003671 453070800420R PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G For Australia 1
8 A-00006733 453070800480R PWRCORD 7A/125V BLK 6FT CNS,VCTF 3Gx0.75 For TWN 1
9 A-00006734 453070800500R PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx For Korea 1
10 N/A 501010202710R BEZEL,FRONT(GRAY),VA702B,LE1709 For VSI&VSA 1
11 N/A 501020202900R COVER,BACK, LE1709 For VSI&VSA 1
12 C-00006088 501020203000R COVER,HINGE, LE1709 For VSI&VSA 2
13 N/A 501030201900R BUTTON,FUNCTION KEY, LE1709 For VSI&VSA 1
14 N/A 501120101200R LENS, LE1709 For VSI&VSA 1
15 N/A 501240201000R BASE, LE1709 For VSI&VSA 1
16 N/A 502020300700R BRACKET,LEFT, LE1709 For VSI&VSA 1
17 N/A 502020300710R BRACKET,RIGHT, LE1709 For VSI&VSA 1
18 HW-00005277 502060401900R HINGE,LEFT, LE1709 For VSI&VSA 1
19 HW-00005276 502060401910R HINGE,RIGHT, LE1709 For VSI&VSA 1
20 N/A 502080300300R SUPPORT,VESA, LE1709 For VSI&VSA 1
21 N/A 502090301300R CHASSIS, LE1709 For VSI&VSA 1
22 N/A 502170300400R PLATE,BASE,LE1709 For VSI&VSA 1
23 N/A 503010001700R RUBBER,SPACER,L25xW10xT4.0mm,LE1709 For VSI&VSA 1
24 N/A 503020002600R RUBBER,FOOT,OD14.1xT2.5mm,3M, LE1708 For VSI&VSA 4
25 N/A 505040202000R INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L For VSI&VSA 1
26 P-00008079 506020006810R CARTON,VA702B, LE1709 For VSI&VSA 1
27 N/A 506037003700R CARDBOARD,COVER,L1120xW980xH120xT5mm,LE1 For VSI&VSA 0.02778
28 N/A 506039001200R CORNER PAPER,820x50x50mm For VSI&VSA 0.0556
29 N/A 506039002301R CORNER PAPER,2050x50x50xT3mm,LE1705 For VSI&VSA 0.05556
30 P-00005257 506040005500R CUSHION,EPS-L, LE1709 For VSI&VSA 1
31 P-00005253 506040005510R CUSHION,EPS-R, LE1709 For VSI&VSA 1
32 N/A 506102000300R LOGO PLATE,VIEWSONIC, LE1709 For VSI&VSA 1
33 N/A 506102000400R LOGO PLATE,VIEWSONIC, LE1709(THREE BIRDS) For VSI&VSA 1
34 N/A 506102000500R LOGO PLATE,VIEWSONIC, LE1709(ELLIPSE) For VSI&VSA 1
35 P-00005272 506120300400R BAG,PE+EPE,L590xW480xT0.6mm (PRINTED)LE1 For VSI&VSA 1
36 N/A 506150001310R PALLET,1120x980x120mm,LE1709 For VSI&VSA 0.01389
37 N/A 506250005112R LBL,AGENCY(VA702B), LE1709(KOREA MARK) For VSI&VSA 1
38 N/A 506380001800R TAPE,WRAPPING TYPE,48mmx50M LE1X04/05 For VSI&VSA 0.004ROL
39 N/A 506380002100R TAPE,WRAPPING TYPE(VIEWSONIC),50mmx75M,L For VSI&VSA 0.00513ROL
40 N/A 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm),LE1709 For VSI&VSA 0.001ROL
41 N/A 506390000400R LABEL,OPENING STAND, LE1709 For VSI&VSA 1
42 N/A 506390000600R LABEL,HI-POT PASS, LE1709 For VSI&VSA 1
43 N/A 506390210110R LABEL,CARTON(8ms),PRC, LE1709 For VSI&VSA 1
44 N/A 506390500100R LABEL,ENERGY STAR, LE1709 For VSI&VSA 1
45 N/A 506431000300R FILM,PE 500mmx900M For VSI&VSA 0.0004ROL
46 N/A 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) For VSI&VSA 1
47 N/A 506440002400R LABEL,BLANK,50x25mm,LE1709(S/N) For VSI&VSA 1
48 N/A 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) For VSI&VSA 0.02778
49 N/A 506440003000R LABEL,BLANK,35x8mm, LE1709 ROHS For VSI&VSA 2
50 HW-00005270 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO For VSI&VSA 2
51 HW-00005271 509016304102R SCREW,I,CROSS,M3*4,Zw,ROHS For VSI&VSA 4
52 HW-00005267 509116822300R SCREW,P,CROSS,M5*22,Ni,ROHS For VSI&VSA 4
53 HW-00005269 509146305300R SCREW,PW,CROSS,W/WAS,M3*5,NI For VSI&VSA 9
54 HW-00005266 509212610300R SCREW,F,CROSS,T.T-4*10,Ni ROHS For VSI&VSA 4
55 HW-00005265 509412610500R SCREW,B,CROSS,T.T-4*10,BLK ,ROHS For VSI&VSA 4
56 N/A 511100001500R CLIP,WIRE.CH-01P(PG), LE1709 For VSI&VSA 1
57 E-00008006 631102071910R LCD PANEL 17" MT170EN01-V7-G1,AM17000057 For VSI&VSA 1
60 N/A 703000000510R KIT,ACCESSORY,VA702B-INL,LE1709 For VSI&VSA 1
61 C-00005262 714020002400R ASSY,BASE, LE1709 For VSI&VSA 1
62 C-00008095 714030002410R ASSY,BEZEL(G),LE1709 For VSI&VSA 1
63 C-00005264 714050002400R ASSY,BACK COVER, LE1709 For VSI&VSA 1
64 N/A 71407276B101R ASSY,FIANL(G,V7/G1&2&3),LE1709-6A0 For VSI&VSA 1
65 N/A 71408276B100R ASSY,PANEL(V7/G1&2&3),LE1709-6A0 For VSI&VSA 1
66 B-00008066 790411300630R PCBA,IF BOARD(V7), LE1709- 6A0 ROHS For VSI&VSA 1
67 B-00005279 790411400600R PCBA,PWR&INV./B, LE1709-6A0 ROHS For VSI&VSA 1
68 B-00005278 790411500000R PCBA,KEYPAD BOARD, LE1709 ROHS For VSI&VSA 1

45
8. Exploded Diagram and Exploded Parts List
A
C
D
D
D C
B
B
D
D B
C
B
C
F F
ViewSonic Corporation
E
Model
E
E
Title Exploded diagram
E Date Rev:

46
EXPLODED PARTS LIST (VA702-1)
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 C-00003154 714030002400 ASSY,BEZEL(S),LE1709 1
2 E-00003048 631102070270 LCD PANEL 17" MT170EN01-V1(INNOLUX) 1
3 B-00003041 790411300600 PCBA,IF BOARD, LE1709-6A0 1
4 CB-00003155 430303000140 HRN LVDS FFC 30P 234mm,ACCX30234KU28MY 1
5 B-00003043 790411400600 PCBA,PWR&INV./B, LE1709-6A0 1
6 HW-00003156 502020300700 BRACKET,LEFT, LE1709 1
7 B-00003172 502090301300 CHASSIS, LE1709 1
8 CB-00003157 430300800320 HRN ASS'Y 4x2P 189mm UL2651#28SZ504479B 1
9 HW-00003158 502020300710 BRACKET,RIGHT, LE1709 1
10 HW-00003159 502060401900 HINGE,LEFT, LE1709 1
11 C-00003160 714050002400 ASSY,BACK COVER, LE1709 1
12 HW-00003161 502060401910 HINGE,RIGHT, LE1709 1
13 B-00003042 790411500000 PCBA,KEYPAD BOARD, LE1709 1
14 CB-00003162 430300100190 HRN ASS'Y 1P 157mm BLACK,UL1007#20 1
15 C-00003163 714020002400 ASSY,BASE, LE1709 1
16 C-00003164 501020203000 COVER,HINGE, LE1709 2
17 M-00003165 505040202000 INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L (Chassis) 1
18 HW-00003166 509412610500 SCREW,B,CROSS,T.T-4*10,BLK (Back cover & Bezel) 4
19 HW-00003167 509212610300 SCREW,F,CROSS,T.T-4*10,Ni (Hinge & Back cover) 4
20 HW-00003168 509016304102 SCREW,I,CROSS,M3*4,Zw (chassis&bracket*4,GND*1) 5
21 HW-00003169 509146305300 SCREW,PW,CROSS W/WAS,M3*5,Ni (PCB&chassis*5, Bracket & Chassis*4) 9
22 HW-00003170 509116822300 SCREW,P,CROSS,M5*22,Ni (Hinge & Base ASM) 4
23 M-00003171 509000000700 BOLT,#4-40x11.8,NiFOR D-SUB/DVI CONN. (D-SUB) 2
EXPLODED PARTS LIST (VA702b-1)

Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 C-00003173 714030002410 ASSY,BEZEL(G),LE1709 1
2 E-00003048 631102070270 LCD PANEL 17" MT170EN01-V1(INNOLUX) 1
3 B-00003041 790411300600 PCBA,IF BOARD, LE1709-6A0 1
4 CB-00003155 430303000140 HRN LVDS FFC 30P 234mm,ACCX30234KU28MY 1
5 B-00003043 790411400600 PCBA,PWR&INV./B, LE1709-6A0 1
6 HW-00003156 502020300700 BRACKET,LEFT, LE1709 1
7 B-00003172 502090301300 CHASSIS, LE1709 1
8 CB-00003157 430300800320 HRN ASS'Y 4x2P 189mm 1
9 HW-00003158 502020300710 BRACKET,RIGHT, LE1709 1
10 HW-00003159 502060401900 HINGE,LEFT, LE1709 1
11 C-00003160 714050002400 ASSY,BACK COVER, LE1709 1
12 HW-00003161 502060401910 HINGE,RIGHT, LE1709 1
13 B-00003042 790411500000 PCBA,KEYPAD BOARD, LE1709 1
14 CB-00003162 430300100190 HRN ASS'Y 1P 157mm BLACK,UL1007#20 1
15 C-00003163 714020002400 ASSY,BASE, LE1709 1
16 C-00003164 501020203000 COVER,HINGE, LE1709 2
17 M-00003165 505040202000 INSULATOR,MYLAR,L79.7xW62.7mm,CHASSIS, L (Chassis) 1
18 HW-00003166 509412610500 SCREW,B,CROSS,T.T-4*10,BLK (Back cover & Bezel) 4
19 HW-00003167 509212610300 SCREW,F,CROSS,T.T-4*10,Ni (Hinge & Back cover) 4
20 HW-00003168 509016304102 SCREW,I,CROSS,M3*4,Zw (chassis&bracket*4,GND*1) 5
21 HW-00003169 509146305300 SCREW,PW,CROSS W/WAS,M3*5,Ni (PCB&chassis*5, Bracket & Chassis*4) 9
22 HW-00003170 509116822300 SCREW,P,CROSS,M5*22,Ni (Hinge & Base ASM) 4
23 HW-00003171 509000000700 BOLT,#4-40x11.8,NiFOR D-SUB/DVI CONN. (D-SUB) 2

47
VA702-1_VA702b-1
TFT LCD Panel 17"
MT170EN01(Innolux)
Block Diagram
Lamp1 Lamp2 12V Panel Interface
1
Power
2 5V
Rectifier &
Filter Circuit
Confidential - Do Not Copy

5V
AP2301
PMBT3906
LDO
24C16 5V-3.3V
Power Feedback 5V-1.8V
Transformer OVP
Transformer1
Panel Enable
On/Off
Brightness
MCU Scaler Brightness

W78E65p TSU16AK
On/Off
XTAL2
AOP605L
14.318MHz
Rectifier &
48
OZ9910 LTV817
Filter Circuit
AOP605L
XTAL1
22.118MHz
Transformer2
Open
Protection
TOP246Y
AC Line Filter
OPP/OCP
24C02
4 3 2 1
9. Block Diagram
3 4
Keypad
Lamp3 Lamp4 AC Socket VGA Connector
Connector
Keyboard VGA Input
AC Input 90V-264V
10. Schematic Diagrams
C820
2200P Y1 R802 C802
10R 1n 500V
C805 C807 ZD802 R804 T801
100u 450V 33n 400V/ NC P6KE200A 68R 1/2W 400V TRF-EI28
1 L802
11 1 5uH 5A
2
R803 10 3 +14V
D801 510K
C803 ZD801 R828
BL4-06 D803 SRF8-10
C808 100R 1W
+ 1
4n7/1KV C810 9.1V

R801 R807 2 C811 1000u 25V 220u 25V 2
R806 R829
3M3 510K 10R 1n 500V 200R
2 3 3
2
Q802
9 2SC1815
L803 B801
D804 8 1 5uH 5A BEAD CORE 3.5x9 1
-
R805 MUR1100 2
VCC5V
1
3M3 3 3
4
L801 2 1 4 D805 SRF5-04 R827 ZD803 ZD804

12mH C812 C826 10K 5.6V 16V
2 3 R824 D806 1000u 10V C814 C822
1000u 10V
R822 510K A02 7 47u 25V 0.1u 50V
3M3
6
1 4 5
C815
R823 R825 47u/25V
3M3 470K R808 R809
R812 10K 100R
6R8 IC801 R810
LTV817 5K1 1%
R820 1M 4 1 R815
6
2
R821 1M 1K R813
1K
L
D
3 2 R814 R811
IC802 1 1K 51K 1%
TOP246Y C C816
0.1u 100V
S
C804 0.47u X2 R816 MEB

275V 6R8 Q801
PMBT3904 C
1
4
D809 R
C801 C806 C818 1N4148W A IC803 R819
2200P Y2 2200P Y2 C813 R817 C817 47u/25V TL431 10K
2
250V 250V 47p 1KV 12K 0.1u 50V R818
C819 3K3 1%
RT801 47u/25V
5R C824
PGND 4700P Y1
F801
2A 250V
CN801
08DA-6S
1
2 VCC5V
L
1 2 3
3
4 BRIGHTNESS
P801 5 ON/OFF
6
C821
AC IN TO SCALER BD CN101 0.1u/50V ViewSonic Corporation
Model
Title POWER SUPPLY

Date Rev:

49
+14V H
R501 3
+ 3M/3kv L
C511 C522 CN504
2.2uF/25V 220uF/25V 2
3 D508 D506
1 BAV99 2 1 BAV99
T501 OP4
EEL-19 22:2600 C524
5V 10P/3KV
2 8 R502 R512
3.9K 1k
D513 SKS20-04AT 3
2 1
CN502
5
IC501 U501
1 8 6 7 H
1 16 2 S1 D1 7
NDRV2 PDRV2 3 G1 D1 6 C527 L
3
2 15 4 S2 D2 5 5P/3KV 2 OVP1
PGND PDRV1 C528 G2 D2 3 D507 D501
R528 R522
3 14 1.0u/25V AOP605 1 BAV99 BAV99
182K 1% 91K 1% NDRV1 HSB
4 13 OP3 2 1
GNDA VIN C530 C535
5 12 +5V 6.8n/50V NC
CT V5000 U502 R513
C529
R523 6 11 AOP605 IS3 510 1%
220P/50V LCT ISEN
100K 1% C503 1 8 T502
7 10 100n/50V 2 S1 D1 7 EEL-19 22:2600 R511
BRIGHTNESS DIM CMP_SST C502 G1 D1
3 6 510 1%
2.2u/25v S2 D2
R524 C504 8 9 4 5 2 8
ENA VSEN G2 D2 H
51K 1% 1n/50V
2 1 3 R503 3
OZ9910G D514 3M/3KV L
+ SKS20-04AT 5 2 CN503
47K 1% C509 3 D503
R526 5V 220uF/25V 6 7 1 BAV99 OP2 D504
ON/OFF OVP1 2 1 BAV99
R527
IS1
3.3M 1%
OVP2 R506 R504 R510
R529 C505 C506 3.9K 1% C526 3.9K 1k
1M 0.01u/25V 4700P/50V IS3 10P/3KV
C507 R505 C508
2200p/50V 1M R507 CN501
22n/25V 3.9K 1%
H
Q501
3
C525 L
2N7002
2 3 5P/3KV 2 OVP2
Item AUO QDI INL 3 D505 D502
1 BAV99 OP1 BAV99
2 1
R509 510Ω 510Ω 560Ω C523 C536
1
6.8n/50V NC R514 510 1%
Q505 Q504 Q503 Q502 IS1
R511 510Ω 510Ω 560Ω
2N7002 2N7002 2N7002 2N7002
2 3 2 3 2 3 2 3 5V R509 510 1%
R524 51KΩ 47KΩ 47KΩ C531 C534 C532 C533 100K

R508
1
0.1u/50V 0.1u/50V 0.1u/50V 0.1u/50V 1
R521 R519 R517 R515

1M 1M 1M 1M
NOTE:
紅色粗線:表示高電壓迴路; D512
1N4148W
D511
1N4148W
D510
1N4148W
D509
1N4148W
紅色虛線:表示易發熱元件; Model
OP4
OP3
OP1
橘色粗線:表示大電流迴路;
OP2
Title INVERTER
Date Rev:

50
U102
VCC5V FS8860-33PJ VCC3.3
CN101 VCC5V
3 2
VIN VOUT VCC3.3 4500-06
VAA1
Inverter
From Power &
ADJ
VAA1 1
+ + VAA2
C169 C102 C103 C104 2
100uF/16V 0.1/50V VAA2 3
100uF/16V 0.1/50V VAA3 BRIGHTNESS
1
4 ON/OFF
VAA3 5
VAA4
6
VAA4
R174
9.1R/2W
U101 C111 + C101
FS8860-18PJ VCC1.8 0.1/50V 100uF/16V
3 2
VIN VOUT VCC1.8
ADJ
+ +
C105 C106 C107
100uF/16V/NC 100uF/16V 0.1/50V
1
R104
4K7
BRIGHTNESS
DIMMER1
C113
1u/16V
VCC5V VLCD R105 R106

Q101 AP2301N VCC5V
VLCD 4K7 10K
S D ON/OFF
R101 G
C108 10K
R170 CCFL_ENABLE
0.1/50V + C114
0 C109 C110 0.1/50V Q103 R157
PANEL_ENABLE Q102 100uF/16V 0.1/50V PMBT3904 4K7

R103 PMBT3906
4K7
R169 Q107
22K PMBT3904
Model
Title DC INPUT
Date Rev:

51
PC5V_VGA
16
R111 R112 R113
11 1 VGA_R R166 0 75 1% 75 1% 75 1% R115 22 C115 47n/25V
RIN
6 R121 47 C121 47n/25V
GNDR
12 2 VGA_G R167 0 R116 22 C116 47n/25V
GIN
7 R122 47 C122 47n/25V
GNDG
13 3 VGA_B R168 0 R117 22 C117 47n/25V
BIN
8 R123 47 C123 47n/25V
GNDB
14 4 R118/NC 470 NC/C118 1000P/50V
SOG
9
15 5 VCC5V
10
TVS101
BAV99
17
CN102 TVS102 C165 C166 C167
DZ11AA1-HW6 BAV99 NC NC NC
TVS103
BAV99
VCC5V
R114 10K
HPD_VGA R107 100

DET_VGA
DDC_SCL_VGA
DDC_SCL_VGA
DDC_SDA_VGA
DDC_SDA_VGA
VSI R110 100 R108 1K
VSYNC
HSI R165 0 R109 1K
HSYNC
TVS104 TVS105 TVS106 TVS107 R119 C119 R120 C120

5V6 5V6 5V6 5V6 2K2 33p/50V 2K2 220p/50V
DDC_SDA_VGA R127 100

R126 100
R125 10K
DDC_SCL_VGA R124 10K
D103
PC5V_VGA
SN4148
D104 U103
VCC5V C124 AT24C02N-10SI
SN4148
0.1/50V 1 8
2 A0 VCC 7
3 A1 WP 6
4 A2 SCL 5
GND SDA ViewSonic Corporation
Model
Title VGA_INPUT
Date Rev:

52
VAD VPLL VDVI VDPLL VPO VDD VCC3.3 VPO
VCC3.3
FB102
BEAD60OHM
104
114
126
117
55
65
35
45
51
53
11
21
84
94
18
87
97
C128 C129 C130 C131 C132 C133 C170 C171
10u/16V 0.1/50V 0.1/50V 0.1/50V 0.1/50V 0.1/50V 0.1/50V 0.1/50V
AVDD_PLL
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD
AVDD
AVDD_MPLL
VDDC
VDDC
VDDC
VDDC
AVDD_DVI
AVDD_DVI
RIN 63 102 PA0 PA[0..9] VCC1.8 VDD
RIN0 LVA3P PA[0..9]
GNDR 62 103 PA1
60 RIN0M LVA3M 106 PA2
GIN GIN0 LVACKP VCC1.8
GNDG 59 107 PA3
61 GIN0M LVACKM 108 PA4 FB103
SOG SOGIN0 LVA2P BEAD60OHM
BIN 58 109 PA5
57 BIN0 LVA2M 110 PA6 C134 C135 C136 C137 C172
GNDB BIN0M LVA1P
37 111 PA7 10u/16V 0.1/50V 0.1/50V 0.1/50V 0.1/50V
HSYNC HSYNC0 LVA1M
VSYNC 38 112 PA8
29 VSYNC0 LVA0P 113 PA9 VAA1 VAD
28 DDC1_CLK/GPO8 LVA0M
DDC1_DAT/GPO7 118 PB0
NC/LVB3P VAA1
119 PB1 PB[0..9]
NC/LVB3M PB[0..9] FB104
120 PB2
40 NC/LVBCKP 121 PB3 BEAD60OHM
R+ NC/LVBCKM
41
43 R- U104 NC/LVB2P
122
123
PB4
PB5
C138
10u/16V
C139 C173
0.1/50V 0.1/50V
G+ NC/LVB2M
44
G- TSU16AK NC/LVB1P
124 PB6
46 125 PB7
47 B+ NC/LVB1M 128 PB8 VAA2 VPLL
49 B- NC/LVB0P 1 PB9
50 CK+ NC/LVB0M
CK- VAA2
R128 390 1% 52 30
VDVI REXT AD0/GPO6 AD0 FB105
77
AD1 AD1 BEAD60OHM
66 78
REFP AD2 AD2
C125 31 C140 C141
AD3/GPO5 AD3 10u/16V 0.1/50V
1u/16V
67 69 CSZ/ALE
REFM CSZ 71 R164 1K
SCL SCL/RDZ
73 70 R163 1K SDA/WRZ VAA3 VDVI
DIMMER1 PWM0 SDA
74 32 R162 1K HWRESET
PWM1 HWRESETZ 72
INT INT VAA3
3 C127 0.1/50V FB106
BYPASS BEAD60OHM
C126 2 C142 C143 C174
AVSS_LPLL VCC3.3 10u/16V 0.1/50V 0.1/50V
22p/50V
33 6 R129 4K7
AVSS_MPLL
XIN BUS TYPE/NC

AVSS_PLL
AVSS_DVI
AVSS_DVI
AVSS_DVI
X102 C164 100p/50V VAA4 VDPLL

C163 100p/50V
C162 100p/50V
GNDC
GNDC
116 GNDC
GNDC
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
14.318MHz
AVSS
AVSS
AVSS
34
XOUT VAA4
C168 FB107
105
115
127
22p/50V BEAD60OHM
68
56
64
36
54
39
42
48
10
20
85
95
19
86
96
C144 C145
10u/16V 0.1/50V
Note: U104 pin4,5,7~9,12~17,22~27,75,76,79~83,88~93,98~101 are all NC (open)

Model
Title SCALER
Date Rev:

53
CN103
AL2309-A0G1Z
PB[0..9]
PB9 RXO0-
PB8 RXO0+ 1
PB7 RXO1- 2
PB6 RXO1+ 3
PB5 RXO2- 4
PB4 RXO2+ 5
6
PB3 RXOC- 7
PB2 RXOC+ 8
PB1 RXO3- 9
PB0 RXO3+ 10
PA[0..9] 11
PA9 RXE0-
PA8 RXE0+ 12
13
PA7 RXE1- 14
PA6 RXE1+ 15
16
PA5 RXE2- 17
PA4 RXE2+ 18
PA3 RXEC- 19
PA2 RXEC+ 20
PA1 RXE3- 21
PA0 RXE3+ 22
23
24
25
26
27
VLCD 28
29
VLCD 30
CN104
DUPON2.0mm/NC
RXO0- 24 23 RXO0+
RXO1- 22 21 RXO1+
RXO2- 20 19 RXO2+
RXOC- 18 17 RXOC+
RXO3- 16 15 RXO3+
RXE0- 14 13 RXE0+
RXE1- 12 11 RXE1+
RXE2- 10 9 RXE2+
RXEC- 8 7 RXEC+
RXE3- 6 5 RXE3+
4 3
2 1
VLCD
Model
Title PANEL INTERFACE

Date Rev:

54
VCC5V VCPU RP101 RP102 RP103
10K 10K 10K
10K
10K
FB108
10K
0
BEAD60OHM
4
3
2
1
4
3
2
1
5
6
7
8
C149
C148 0.1/50V
VCPU 10u/16V
35 R131
30 R132
31 R133
R134
U105
5
6
7
8
5
6
7
8
4
3
2
1
C150
44
10u/16V Winbond W78E65P
43
HWRESET
EA
P0.0
P2.6
P2.7
VDD
42
P0.1 CSZ/ALE
10 41
RST P0.2 SCL/RDZ
14 40
INT P3.2/INT0 P0.3 SDA/WRZ
VCPU 39
P0.4 AD0
D102 32 38
R137 PSEN P0.5 AD1
37
SN4148 10K P0.6 AD2
36
R138 R139 C151 P0.7 AD3
1 8 10K 10K 0.1/50V
2 A0 VCC 7 12 ISP for Standard
3 A1 WP 6 R140 100 16 P4.3/INT2 LED_GREEN 6
8051
4 A2 SCL 5 R141 100 17 P3.4/T0 LED_ORANGE 8
GND SDA 18 P3.5/T1 24 R146 1K KEY_POWER 4
TO KEY PAD
P3.6/WR P2.0 25 R147 1K KEY_SELECT/AUTO 1
U106 P2.1
24C16 VCPU 26 R148 1K KEY_UP 3
8 P2.2 27 R149 1K KEY_DOWN 5
9 P1.6/PWM3 P2.3 28 R150 1K KEY_MENU/EXIT 2
P1.7/PWM4 P2.4
1
2
3
4
23 29 7
33 P4.0 P2.5
RP104 ALE
34
10K P4.1
1000P/50V
1000P/50V
1000P/50V
1000P/50V
1000P/50V
19 CN106
2 P3.7 VCPU 2x4PIN
8
7
6
5
PANEL_ENABLE P1.0
3
CCFL_ENABLE P1.1
4 15
C156
C157
C158
C159
C160
DET_VGA P1.2 P3.3/INT1
5 R156 R155
6 P1.3
P1.4 10K 10K
VCPU 7
P1.5
1 13 R153 100
P4.2 P3.1/TXD R152 DDC_SDA_VGA
C153 11 100
R142 R143 R144 P3.0/RXD DDC_SCL_VGA
NC/10u/16V 22
X2
X1
220 4K7 4K7 VSS

20
21
Q104 VCPU
PMBT3906
LED_GREEN
R145
R158 220 X101
C154 C155
51 12p/50V 22.1184MHz 12p/50V
Q105
PMBT3906
LED_ORANGE
R159 ViewSonic Corporation
220
Model
Title MCU
Date Rev:

55
LED_GREEN 6
LED_ORANGE 8
KEY_MENU/EXIT 2
KEY_SELECT/AUTO 1
LED101 KEY_POWER 4
GREEN ORANGE KEY_DOWN 5
KEY_UP 3
7
SW101 SW102 SW103 SW104 SW105

CN106
2x4PIN
SW TACT SW TACT SW TACT SW TACT SW TACT
MENU/1 AUTO/2 POWER DOWN UP
Model
Title KEYPAD
Date Rev:

56
11. PCB Layout Diagrams
Main board Top layout

57
Main board bottom Layout

58
POWER board

59
60
* Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagrams
10. Schematic Diagrams
11.PCB Layout Diagrams
B. Are you satisfied with this Service Manual?

Item Excellent Good Fair Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:

Name: Title:
Company:
Add:
Tel: Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
([email protected])

61

Va702-1 SM

Uploaded by

Copyright:

Available Formats

Va702-1 SM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Va702-1 SM

Uploaded by

Copyright:

Available Formats

Service Manual

(VA702-1_ VA702b-1_SM Rev. 1b Sep. 2006)

1a 10/20/05 Initial Release G. Han

1b 9/12/2006 Add 2 nd panel V7 & VA (updated RSPL, BOM) Jamie Chang

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

1. Precautions and Safety Notices 1

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Correct Methods: Incorrect Methods:

Taking out the monitor by grasping the LCD panel.

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

The panel is placed facedown on the lap. That may

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Test Resolution & Frequency 1280x1024 @ 60Hz

Analog Input Connector DB-15 (Analog), refer the appendix A

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Internal Power Supply Part Number: ILIPI-004

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Horizontal / Vertical Frequency

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

TFT LCD PANEL

1st Source Panel

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Model number Innolux MT170EN01 V4

Response Time 8 ms (Tr= 2 ms, Tf = 6 ms) (typ)

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

VIEWING ANGLE (VERTICAL) @ CR>=10 @ CR>=10

Response Time 8 ms (Tr= 2 ms, Tf = 6 ms) (typ)

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Preset Color Temperatures

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Adjusting the Screen Image

Front Control Panel

Displays the control screen Power light

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

4. To adjust the setting, press the upSor downTbuttons.

The following tips may help you optimize your display:

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Brightness adjusts background black level of the screen image.

5400K - Adds green to the screen image for a darker color.

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Manual Image Adjust

H./V. Position (Horizontal/Vertical Position) moves the screen image left or

H. Size (Horizontal Size) adjusts the width of the screen image.

Sharpness adjusts the clarity and focus of the screen image.

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

Setup Menu displays the menu shown below:

Resolution Notice advises the optimal resolution to use.

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

ViewSonic Corporation Confidential - Do Not Copy VA702-1_VA702b-1

3 I/F Board Circuit

3. FACTORY PRESET TIMING TABLE

H-Freq. V-Freq. Dot Clock

4.2 Software Power ON/OFF

T1 (ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6 (ms) T7 (ms)

5. AC Outlet Pin Assignment

Pin Symbol Description

BEZEL SUB-ASSM 1 FRONT BEZEL (G/S)1 LED LENS*1

CHASSIS1 FRONT BEZEL (G/S)1 LED LENS*1

LOGO PLATE,THREE BRID1 BUTTON FUNCTION KEY1

BRACKET_R1 PLATE BASE 1 BASE COVER *1