UHF FM TRANSCEIVER

PKT-03
SERVICE MANUAL
K,M Versions © 2013-7 PRINTED IN JAPAN
RQ007 (K) PDF (B53-7059-00)

Cover (ANT)
(F07-1971-02)

CAP (Phone/USB)
(B09-0760-03)

CONTENTS
GENERAL ....................................................2
REALIGNMENT ...........................................3
SEMICONDUCTOR DATA ...........................4
Key top
(K29-9621-12)
COMPONENTS DESCRIPTION ..................5
PARTS LIST .................................................6
EXPLODED VIEW ........................................9
ADJUSTMENT ...........................................10
PC BOARD
TX-RX UNIT (X57-8490-22) ....................14
SCHEMATIC DIAGRAM ............................16
BLOCK & LEVEL DIAGRAM.....................18
OPTIONAL ACCESSORIES (KNB-71L) ...19
SPECIFICATIONS .................. BACK COVER

Plastic cabinet assy(FRONT)

(A02-4216-13)

This product complies with the RoHS directive for the European market. This product uses Lead Free solder.
PKT-03

Document Copyrights Disclaimer

Copyright 2013 by JVC KENWOOD Corporation. All While every precaution has been taken in the preparation
rights reserved. of this manual, JVC KENWOOD Corporation assumes no
No part of this manual may be reproduced, translated, responsibility for errors or omissions. Neither is any liability
distributed, or transmitted in any form or by any means, assumed for damages resulting from the use of the informa-
electronic, mechanical, photocopying, recording, or other- tion contained herein. JVC KENWOOD Corporation reserves
wise, for any purpose without the prior written permission of the right to make changes to any products herein at any time
JVC KENWOOD Corporation. for improvement purposes.

GENERAL

INTRODUCTION PERSONAL SAFETY

SCOPE OF THIS MANUAL The following precautions are recommended for personal
This manual is intended for use by experienced techni- safety:
cians familiar with similar types of commercial grade com- • DO NOT transmit until all RF connectors are verified
munications equipment. It contains all required service secure and any open connectors are properly terminated.
information for the equipment and is current as of the pub- • SHUT OFF and DO NOT operate this equipment near
lication date. Changes which may occur after publication electrical blasting caps or in an explosive atmosphere.
are covered by either Service Bulletins or Manual Revisions. • This equipment should be serviced by a qualified techni-
These are issued as required. cian only.

ORDERING REPLACEMENT PARTS SERVICE

When ordering replacement parts or equipment informa- This transceiver is designed for easy servicing. Refer
tion, the full part identification number should be included. to the schematic diagrams, printed circuit board views, and
This applies to all parts : components, kits, or chassis. If the alignment procedures contained within.
part number is not known, include the chassis or kit number
of which it is a part, and a sufficient description of the re- Frequency
Model TX-RX unit Remarks
quired component for proper identification. range
PKT-03 X57-8490-22 440~480MHz K,M Type

2
 PKT-03
REALIGNMENT
1. Modes 3-4 Programming Software KPG-164D Description
The KPG-164D is the programming software for the
User mode
transceiver supplied on a CD-ROM. This software runs un-
der windows XP, Vista, 7 or 8 on a PC. The software on this
PC mode Data programming mode disk allows a user to program the transceiver via Program-
ming interface cable (commercial micro-USB cable).

PC test mode PC tuning mode

Note:
• Use the FPU that matches the market when you first set
Mode Function
the market code and model name/frequency data to the
User mode For normal use. service unit. The unit set by mistake cannot be restored.
Used for communication between the trans-
PC mode
ceiver and PC. • The item of "Tuning Data" of a new function is added to
KPG-164D.
Data programming Used to read and write frequency data and
mode other features to and from the transceiver.
In the Tuning Data dialog box, adjustment data in the
transceiver can be read into KPG-164D, and the read
Used to check the transceiver using the PC. adjustment data can be saved as a file by a service
PC test mode
This feature is included in the FPU. engineer. The saved adjustment data file can be load into
KPG-164D, and written into the transceiver.
2. How to Enter Each Mode Please be sure to all adjustment item after data Writing.

Mode Operation • Receive frequencies listed below may result in the in-
User mode Power ON terference of reception due to the harmonics of internal
PC mode Received commands from PC oscillators. Enter a frequency not listed in the table.

3. PC Mode No. Frequency (MHz)

3-1. Preface 1 441.59500
The transceiver is programmed by using a personal com- 2 441.60000
puter, a programming interface (Micro-USB interface cable) 3 441.60500
and FPU programming software . 4 460.79375
The programming software can be used with a PC. Fig- 5 460.79500
ure 1 shows the setup of a PC for programming. 6 460.80000
7 460.80500
3-2. Connection Procedure 8 460.80625
1. Connect the transceiver to the personal computer with
the interface cable. • The transmission using the high transmit power on the
Note: transmit frequencies ranging from 460.3 MHz to 461.3
• You must install the USB driver in the computer to use MHz may not be compliant with the USA FCC rules;
the USB programming interface cable . (Micro-USB) therefore, configuring the transmit frequency of this range
automatically configures "Low" for Transmit Power.
2. When data is read from the transceiver, the red LED
lights.
When data is written to the transceiver, the green LED
lights.

3-3. USB programming cable Description

( Commercial micro-USB cable)
The micro-USB is a cable which connects to a USB port
on a computer.
When using the micro-USB cable, install the supplied
CD-ROM (with driver software) in the computer. The driver
runs under Windows XP, Vista, 7 or 8.

3
PKT-03
REALIGNMENT
3-5. Programming with PC PC
If data is transferred to the transceiver from a PC with the
FPU, the data for each set can be modified.
In this mode, it operates in a USB format from a micro-
USB jack.

FPU Commercial micro-USB cable.

Fig.1

SEMICONDUCTOR DATA
MCU:F21348UKEZA (TX-RX unit IC3)
Pin No Signal Name I/O Function
Pin No. Signal Name I/O Function
APC dischage contorol (active :
1 TRWP O Transceiver IC chip select 25 DISCSW O
HI)
2 PDN O Deep sleep select 26 H/L O TX power control (Low : "H")
3 VREF - +3.3V 27 CHG I Battery chage state
4 MODE - Reserve 28 33TC/T/R O 33T contorol (active : HI)
5 SQIN I SQ status level 29 33MC O 33M contorol (active : HI)
6 QTIN I QT status level EXT earphone detection (active :
30 EPTDET I
Low)
7 RESET I Reset
31 POWER I Power key (active : HI)
8 XOUT - 12MHz resonator
32 LIGHT O Light LED control ("H": ON)
9 Vss/AVSS - Graund
33 DOWN I Down key (active : Low)
10 XIN I 12MHz resonator
34 UP I Up key (active : Low)
11 Vcc/AVCC - +3.3V
35 PTT I PTT key (active : Low)
12 SP_MUTE O SO/AF mute contorol (active : HI)
36 FNC I Function key (active : Low)
13 TYPE1 I Type discrimination 1
37 P_TEMP I Temperture detection (TX PA)
14 ATT1 O Voice guide level attenuator 1
38 CURRENT I Battry level detection (at TX)
15 ATT2 O Voice guide level attenuator 2
39 BATT I Battry level detection
16 MIC_ATT O MIC sensitivity attenuator
40 VOICE_DATA O Voice guide announce
17 MIC_MUTE O Reserve
41 RED O Red LED control ("H": ON)
18 USB_VBUS - +3.3V
42 GREEN O Green LED control ("H": ON)
19 USB_DM I/O USB data line +
43 BLUE O Blue LED control ("H": ON)
20 USB_DP I/O USB data line - 44 TYPE2 I Type discrimination 2
21 USB_VCC - +3.3V 45 EPWP O Reserve
22 USB_DPUPE I PC conect detection 46 E2PIN I Reserve
23 NC - Not conect 47 SCLK O Serial clock
24 NC - Not conect 48 SDIO I/O Serial data

4
 PKT-03
COMPONENTS DESCRIPTION
TX-RX unit (X57-8490-22)
Ref. No. Part Name Description
IC2 IC Reset(for MCU)
IC3 IC MCU
IC100 IC Transceiver system
IC200 IC A/2 : MIC AMP, B/2 : Buffer AMP
IC201 IC AF Power AMP
IC300 IC Battery charge system
IC301 IC 3.3V regulator
Q3 FET DC Switch
Q101 FET DC Switch
Q200 Transistor DC Switch (voice ATT 1)
Q201 Transistor DC Switch (voice ATT 2)
Q203 Transistor MIC sensitivity switch
Q205 FET DC Switch (AF mute)
Q206,207 Transistor DC Switch (SP mute)
Q208 FET AF AMP shutdown
Q300 FET DC Switch (33T)
Q402 Transistor LED switch (blue)
Q403 Transistor LED switch (red)
Q404 Transistor LED switch (green)
Q405 Transistor Flash light LED switch (white)
Q501 Transistor TX pre-drive AMP
Q502 FET TX drive AMP
Q503 Transistor DC Switch (HI/Low)
Q504 FET TX final AMP
Q505 Transistor APC discharge switch
Q506 FET DC Switch (current detection)
Q507 FET RX RF AMP
Q508 FET DC Switch (HI/Low)
D201 Diode OR (Q208 control line)
D300 Zener diode Over voltage protection
D301 Zener diode Surge protection
D302,303 Diode OR (IC301 STBY line)
D402 LED LED (red/green/blue)
D405 LED Flash light LED (white)
D501,502 Diode ANT Switch

5
PKT-03
PARTS LIST
✽ New Parts. indicates safety critical components. L : Scandinavia K : USA P : Canada
Parts without Parts No. are not supplied. Y : PX (Far East, Hawaii) T : England E : Europe
Les articles non mentionnes dans le Parts No. ne sont pas fournis. C : China X : Australia M : Other Areas
Teile ohne Parts No. werden nicht geliefert.
PKT-03
TX-RX UNIT (X57-8490-22)
New
Ref. No. Address parts Parts No. Description Desti- New
Ref. No. Address parts Parts No. Description Desti-
nation nation

PKT-03 C109 CC73HCH1H471J CHIP C 470PF J

C110 CK73HB1E104K CHIP C 0.10UF K
1 3B A02-4216-13 PLASTIC CABINET ASSY(FRONT) C200,201 CK73HB1E104K CHIP C 0.10UF K
2 1A A02-4217-02 PLASTIC CABINET(REAR) C208 CK73FB0J106K CHIP C 10UF K
3 2A ∗ A13-1664-12 FRAME C209,210 CK73HB1E104K CHIP C 0.10UF K

4 3B B09-0760-03 CAP(PHONE/USB) C211,212 CK73HB1A105K CHIP C 1.0UF K

5 3A E37-1684-05 PROCESSED LEAD WIRE(SP) C213 CK73HB1E104K CHIP C 0.10UF K
6 2B F07-1971-02 COVER(ANT) C214 CK73FB0J226M CHIP C 22UF M
C215 CC73HCH1H471J CHIP C 470PF J
7 2A G10-1853-04 FIBROUS SHEET(FRAME) C216 CK73HB1A105K CHIP C 1.0UF K
8 2A ∗ G11-4643-04 RUBBER SHEET(FRAMEx3)
C217 CK73HB1E223K CHIP C 0.022UF K
10 2A G53-2223-02 PACKING(CABINET) C218 CK73HB1A105K CHIP C 1.0UF K
C219 CK73HB1A224K CHIP C 0.22UF K
11 2B ∗ K29-9621-12 KEY TOP C220 CK73HB1A105K CHIP C 1.0UF K
A 2A N80-2006-48 PAN HEAD TAPTITE SCREW C221 CK73FB0J106K CHIP C 10UF K
B 1A N80-2008-43 PAN HEAD TAPTITE SCREW
C223-225 CC73HCH1H471J CHIP C 470PF J
12 3B ∗ T07-0787-15 SPEAKER C227 CC73HCH1H471J CHIP C 470PF J
13 2B ∗ T90-1128-05 ANTENNA ELEMENT C229 CC73HCH1H470J CHIP C 47PF J
14 1A KNB-71L BATTERY PACK C230 CC73HCH1H471J CHIP C 470PF J
(SALES ORDER) C301 CK73HB1A105K CHIP C 1.0UF K

ACCESSORY C308 CK73HB1A105K CHIP C 1.0UF K

B62-2525-00 INSTRUCTION MANUAL ACCESSORY C310 CK73HB1A105K CHIP C 1.0UF K
∗ B62-2565-00 NSTRUCTION MANUAL(S)ACCESSORY K C317 CK73HB1A105K CHIP C 1.0UF K
C319 CC73HCH1H471J CHIP C 470PF J
∗ X57-8490-23 TX-RX UNIT(FOR SERVICE) C323 CC73HCH1H471J CHIP C 470PF J

C327 CC73HCH1H471J CHIP C 470PF J

C328 CK73HB1A105K CHIP C 1.0UF K
C333 CC73HCH1H471J CHIP C 470PF J
C349 CK73FB1A475K CHIP C 4.7UF K
C350 CC73HCH1H471J CHIP C 470PF J

C351 CK73GB0J225K CHIP C 2.2UF K

C500 CC73HCH1H471J CHIP C 470PF J
C503 CC73HCH1H080B CHIP C 8.0PF B
TX-RX UNIT (X57-8490-22) C504 CC73HCH1H330J CHIP C 33PF J
C505 CC73HCH1H040B CHIP C 4.0PF B
D405 2A B30-2354-05 LED(WHITE)
D402 B30-2355-05 LED(RED/GREEN/BLUE) C506,507 CC73HCH1H471J CHIP C 470PF J
C510,511 CC73HCH1H471J CHIP C 470PF J
C9 CC73HCH1H471J CHIP C 470PF J C512 CK73HB1E104K CHIP C 0.10UF K
C12 CK73HB1A105K CHIP C 1.0UF K C513 CC73HCH1H471J CHIP C 470PF J
C13 CC73HCH1H471J CHIP C 470PF J C514 CK73HB1E104K CHIP C 0.10UF K
C14 CK73HB1A105K CHIP C 1.0UF K
C15 CK73HB1E104K CHIP C 0.10UF K C515 CC73HCH1H221J CHIP C 220PF J
C516 CC73HCH1H100D CHIP C 10PF D
C16 CK73FB0J106K CHIP C 10UF K C517 CC73HCH1H270J CHIP C 27PF J
C18 CC73HCH1H471J CHIP C 470PF J C518 CC73HCH1H080B CHIP C 8.0PF B
C19 CK73HB1E104K CHIP C 0.10UF K C519 CC73HCH1H270J CHIP C 27PF J
C20-22 CC73HCH1H471J CHIP C 470PF J
C23 CK73HB1E104K CHIP C 0.10UF K C520,521 CC73HCH1H471J CHIP C 470PF J
C522 CK73HB1E104K CHIP C 0.10UF K
C100 CC73HCH1H471J CHIP C 470PF J C523 CK73HB1H103K CHIP C 0.010UF K
C101 CK73HB1E104K CHIP C 0.10UF K C524 CC73GCH1H270J CHIP C 27PF J
C102 CC73HCH1H471J CHIP C 470PF J C525,526 CC73HCH1H471J CHIP C 470PF J
C103 CK73HB1E104K CHIP C 0.10UF K
C104 CK73FB0J226M CHIP C 22UF M C528 CC73GCH1H150J CHIP C 15PF J
C529 CC73GCH1H050B CHIP C 5.0PF B
C105 CC73HCH1H471J CHIP C 470PF J C530,531 CC73HCH1H471J CHIP C 470PF J
C106 CK73HB1E104K CHIP C 0.10UF K C532 CC73GCH1H150J CHIP C 15PF J
C107 CC73HCH1H471J CHIP C 470PF J C533 CC73HCH1H060B CHIP C 6.0PF B
C108 CK73HB1E104K CHIP C 0.10UF K

6 If a part reference number is listed in a shaded box, that part does not come with the PCB.
 PKT-03
PARTS LIST
TX-RX UNIT (X57-8490-22)

Ref. No. New

Address parts Parts No. Description Desti- New
Ref. No. Address parts Parts No. Description Desti-
nation nation
C534 CC73HCH1H471J CHIP C 470PF J R60 RK73HB1J103J CHIP R 10K J 1/16W
C535 CC73GCH1H181J CHIP C 180PF J R61 RK73HB1J271J CHIP R 270 J 1/16W
C536 CC73HCH1H471J CHIP C 470PF J R79 RK73HB1J000J CHIP R 0 J 1/16W
C537 CC73GCH1H050B CHIP C 5.0PF B R82,83 RK73GB2A000J CHIP R 0 J 1/10W
C538 CC73HCH1H060B CHIP C 6.0PF B R100 RK73HB1J473J CHIP R 47K J 1/16W

C539 CC73GCH1H1R5B CHIP C 1.5PF B R101,102 RK73HB1J103J CHIP R 10K J 1/16W

C540 CC73HCH1H471J CHIP C 470PF J R200 RK73HB1J331J CHIP R 330 J 1/16W
C541 CC73GCH1H080B CHIP C 8.0PF B R201 RK73HB1J103J CHIP R 10K J 1/16W
C542 CC73HCH1H471J CHIP C 470PF J R202 RK73HB1J221J CHIP R 220 J 1/16W
C543 CC73GCH1H1R0B CHIP C 1.0PF B R203 RK73HB1J561J CHIP R 560 J 1/16W

C544 CC73GCH1H2R5B CHIP C 2.5PF B R204,205 RK73HB1J000J CHIP R 0 J 1/16W

C546,547 CK73HB1E104K CHIP C 0.10UF K R206 RK73HB1J271J CHIP R 270 J 1/16W
C548 CC73HCH1H271J CHIP C 270PF J R207 RK73HB1J332J CHIP R 3.3K J 1/16W
C549-552 CC73HCH1H471J CHIP C 470PF J R212 RK73HB1J471J CHIP R 470 J 1/16W
C553 CC73HCH1H080B CHIP C 8.0PF B R213 RK73HB1J182J CHIP R 1.8K J 1/16W

C554 CC73HCH1H180J CHIP C 18PF J R214-217 RK73HH1J473D CHIP R 47K D 1/16W

C555 CK73HB1E104K CHIP C 0.10UF K R218 RK73HB1J103J CHIP R 10K J 1/16W
C556 CC73HCH1H471J CHIP C 470PF J R219,220 RK73HB1J473J CHIP R 47K J 1/16W
C558 CC73GCH1H181J CHIP C 180PF J R221 RK73HB1J000J CHIP R 0 J 1/16W
C560 CC73HCH1H040B CHIP C 4.0PF B R222 RK73HB1J222J CHIP R 2.2K J 1/16W

C562 CC73HCH1H120J CHIP C 12PF J R223 RK73HB1J821J CHIP R 820 J 1/16W

C563 CC73HCH1H040J CHIP C 10PF J R224 RK73HB1J102J CHIP R 1.0K J 1/16W
C565 CC73HCH1H040B CHIP C 4.0PF B R225 RK73HB1J473J CHIP R 47K J 1/16W
C219 CK73HB1A224K CHIP C 0.22UF K R226 RK73HB1J102J CHIP R 1.0K J 1/16W
C220 CK73HB1A105K CHIP C 1.0UF K R227 RK73HB1J150J CHIP R 15 J 1/16W

C221 CK73FB0J106K CHIP C 10UF K R230 RK73HB1J474J CHIP R 470K J 1/16W

R231 RK73HB1J103J CHIP R 10K J 1/16W
CN305 E40-6957-05 PIN ASSY(3P) R232 RK73HB1J393J CHIP R 39K J 1/16W
CN307 E23-1167-05 TERMINAL R233 RK73HB1J474J CHIP R 470K J 1/16W
CN310 E23-1167-05 TERMINAL R234 RK73HB1J473J CHIP R 47K J 1/16W
CN314 E23-1167-05 TERMINAL
R235 RK73HB1J473J CHIP R 47K J 1/16W
J200 2A E11-0719-05 3.5D PHONE JACK(EXT PHONE) R236 RK73HB1J223J CHIP R 22K J 1/16W
J300 E58-0566-05 RECTANGULAR RECEPTACLE R237 RK73HB1J101J CHIP R 100 J 1/16W
F300 F53-0367-05 FUSE(1.0A) R238 RK73HB1J000J CHIP R 0 J 1/16W
R239 RK73HB1J103J CHIP R 10K J 1/16W
16 3A J31-0568-05 COLLAR(D405)
R240 RK73HB1J101J CHIP R 100 J 1/16W
L200 L92-0163-05 BEADS CORE R241 RK73HB1J223J CHIP R 22K J 1/16W
L501 L40-1275-71 SMALL FIXED INDUCTOR(12NH) R242 RK73HB1J104J CHIP R 100K J 1/16W
L502 L40-2275-71 SMALL FIXED INDUCTOR(22NH) R301 RK73HB1J124J CHIP R 120K J 1/16W
L503 L40-6865-71 SMALL FIXED INDUCTOR(6.8NH) R302 RK73HB1J152J CHIP R 1.5K J 1/16W
L504 L41-2275-45 SMALL FIXED INDUCTOR(22NH)
L505 L41-2263-53 SMALL FIXED INDUCTOR(2.2NH) R303 RK73HB1J683J CHIP R 68K J 1/16W
L506 ∗ L41-1563-53 SMALL FIXED INDUCTOR(1.5NH) R313,314 RK73HB1J270J CHIP R 27 J 1/16W
L507 L41-2285-45 SMALL FIXED INDUCTOR(220NH) R330 RK73HB1J102J CHIP R 1.0K J 1/16W
L508 L34-4571-71 AIR-CORE COIL(3T) R331 RK73HB1J152J CHIP R 1.5K J 1/16W
L509 L41-3963-14 SMALL FIXED INDUCTOR(3.9NH) R332 RK73HB1J473J CHIP R 47K J 1/16W
L510 L41-3385-14 SMALL FIXED INDUCTOR(330NH)
L511 L34-4572-05 AIR-CORE COIL(4T) R333 RK73HB1J823J CHIP R 82K J 1/16W
L512 L41-2785-45 SMALL FIXED INDUCTOR(270NH) R334 RK73HB1J104J CHIP R 100K J 1/16W
L513 L34-4572-05 AIR-CORE COIL(4T) R342.343 RK73HB1J000J CHIP R 0 J 1/16W
L515 L34-4572-05 AIR-CORE COIL(4T) R344 RK73HB1J563J CHIP R 56K J 1/16W
L517 L40-1875-71 SMALL FIXED INDUCTOR(18NH) R345 RK73HB1J822J CHIP R 8.2K J 1/16W
X1 ∗ L77-3126-05 TCXO(25.6MHZ) R348 RK73HB1J223J CHIP R 22K J 1/16W
X2 L78-1438-05 RESONATOR(12.00MHZ)
R349 RK73HB1J821J CHIP R 820 J 1/16W
R3 RK73HB1J473J CHIP R 47K J 1/16W R402 RK73HB1J151J CHIP R 150 J 1/16W
R6 RK73HB1J473J CHIP R 47K J 1/16W R403 RK73HB1J271J CHIP R 270 J 1/16W
R8-10 RK73HB1J473J CHIP R 47K J 1/16W R404 RK73HB1J101J CHIP R 100 J 1/16W
R13 RK73HB1J153J CHIP R 15K J 1/16W R405 RK73HB1J470J CHIP R 47 J 1/16W
R18 RK73HB1J393J CHIP R 39K J 1/16W
R505 RK73HB1J220J CHIP R 22 J 1/16W
R21,22 RK73HB1J473J CHIP R 47K J 1/16W R506 RK73HB1J102J CHIP R 1.0K J 1/16W
R32 RK73HB1J334J CHIP R 330K J 1/16W R507 RK73HB1J222J CHIP R 2.2K J 1/16W
R44 RK73HB1J472J CHIP R 4.7K J 1/16W R508 RK73HB1J470J CHIP R 47 J 1/16W

If a part reference number is listed in a shaded box, that part does not come with the PCB. 7
PKT-03
PARTS LIST
TX-RX UNIT (X57-8490-22)
New
Ref. No. Address parts Parts No. Description Desti- Ref. No. New
Address parts Parts No. Description Desti-
nation nation
R509 RK73HB1J332J CHIP R 3.3K J 1/16W Q502 RFM01U7P FET
R511 RK73HB1J100J CHIP R 10 J 1/16W Q503 LTC014EEBFS8 TRANSISTOR
R512 RK73GB2A153J CHIP R 15K J 1/10W Q504 RFM03U3CT FET
R513 RK73HB1J104J CHIP R 100K J 1/16W Q505 LTC014EEBFS8 TRANSISTOR
R514 RK73HB1J183J CHIP R 18K J 1/16W Q506 SSM6L36TU-F FET

R515 RK73HB1J223J CHIP R 22K J 1/16W Q507 3SK318 FET

R516 RK73HB1J473J CHIP R 47K J 1/16W Q508 SSM6N17FU FET
R517 RK73HB1J121J CHIP R 120 J 1/16W
R518 RK73HB1J104J CHIP R 100K J 1/16W TH500 B57331V2104J THERMISTOR
R519 RK73HB1J331J CHIP R 330 J 1/16W

R520 RK73HB1J393J CHIP R 39K J 1/16W

R521 RK73HB1J473J CHIP R 47K J 1/16W
R522 RK73HB1J393J CHIP R 39K J 1/16W
R523 RK73HB1J153J CHIP R 15K J 1/16W
R524 R92-3637-05 CHIP R 0.39 J 1/3W

R525 RK73HB1J121J CHIP R 120 J 1/16W

R526 R92-3637-05 CHIP R 0.39 J 1/3W
R527 RK73HB1J470J CHIP R 47 J 1/16W
R528 R92-3637-05 CHIP R 0.39 J 1/3W
R529 RK73HB1J470J CHIP R 47 J 1/16W

R530 RK73HB1J220J CHIP R 22 J 1/16W

R531 RK73HB1J470J CHIP R 47 J 1/16W
R532 RK73HB1J104J CHIP R 100K J 1/16W
R534 RK73HB1J104J CHIP R 100K J 1/16W
R535 RK73HB1J683J CHIP R 68K J 1/16W

R536 RK73HB1J104J CHIP R 100K J 1/16W

R537 RK73HB1J473J CHIP R 47K J 1/16W
R538 RK73HB1J270J CHIP R 27 J 1/16W
R540 RK73HB1J332J CHIP R 3.3K J 1/16W
R541 RK73HB1J000J CHIP R 0 J 1/16W

R543 RK73HB1J473J CHIP R 47K J 1/16W

S2 S70-0516-05 TACT SWITCH

S3-6 S70-0519-05 TACT SWITCH

MIC1 3A T91-0673-05 MIC ELEMENT

D201 DAN222WM DIODE

D300 DZ2J062(M) ZENER DIODE
D301 RSB12JS2 ZENER DIODE
D302 DAN222WM DIODE
D303 DA2J101 DIODE

D501,502 RN142S DIODE

IC2 BU4827F MOS-IC

IC3 F21348UKEZA MCU
IC100 Note 1 MOS-IC
IC200 NJM13404RB1 MOS-IC
IC201 NJU7089KV1 MOS-IC

IC300 BQ24086DRCR MOS-IC

IC301 BU33TD3WG MOS-IC

Q3 SSM6L36TU-F FET
Q101 2SK1824-A FET
Q200,201 LTC014EEBFS8 TRANSISTOR
Q203 LTC014EEBFS8 TRANSISTOR
Q205 MTM76520 FET

Q206,207 LTC014EEBFS8 TRANSISTOR

Q208 2SK1824-A FET
Q300 SSM3J36TUT FET
Q402-405 LTC023JEBFS8 TRANSISTOR
Q501 2SC4926YD TRANSISTOR

8 If a part reference number is listed in a shaded box, that part does not come with the PCB.
Note 1: This part cannot be replaced. Therefore, this part is not supplied as a service part.
 PKT-03
EXPLODED VIEW
A B

Bx4
700 A Ø2 x 6 : N80-2006-48

B Ø2 x 8 : N80-2008-43

2
1

14

Solder

10

7
Ax3
3
6
2

D405 X57

16 X57
J200 X57

13

8x3
11

TX-RX unit
X57-849

12 4

MIC1 X57

3 5

Parts with the exploded numbers larger than 700 are not supplied.
9
If a part reference number is listed in a box on the exploded view of the PCB, that part does not come with the PCB.
These parts must be ordered separately.
PKT-03
ADJUSTMENT
Test Equipment Required for Alignment
Test Equipment Major Specifications
Frequency Range 400 to 500MHz
1. Standard Signal Generator (SSG) Modulation Frequency modulation and external modulation
Output –127dBm/0.1µV to greater than –47dBm/1mV
Input Impedance 50Ω
2. RF Power Meter Operation Frequency 400 to 500MHz
Measurement Range Vicinity of 10W
3. Deviation Meter Frequency Range 400 to 500MHz
Measuring Range 10mV to 10V DC
4. Digital Volt Meter (DVM)
Input Impedance High input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. High Sensitivity Frequency Range 10Hz to 1000MHz
Frequency Counter Frequency Stability 0.2ppm or less
7. DC Ammeter 5A
Frequency Range 50Hz to 10kHz
8. AF Volt Meter (AF VM)
Voltage Range 1mV to 10V
Frequency Range 50Hz to 5kHz or more
9. Audio Generator (AG)
Output 0 to 1V
Capability 3% or less at 1kHz
10. Distortion Meter
Input Level 50mV to 10Vrms
11. Spectrum Analyzer Measuring Range 10kHz to 1GHz or more
Center frequency 50kHz to 600MHz
12. Tracking Generator
Output Voltage 100mV or more
13. 32Ω Dummy Load Approx. 32Ω, 0.5W
2V to 5V, approx. 3A
14. Regulated Power Supply
Useful if ammeter equipped
The test equipment which is not used for adjustment is contained in this table.

Service Jig ■ Measuring instrument connection diagram

ϮANT cable (E30-3418-25)
Modify the cable as shown below. To AF VM
Distortion Meter JIG ANT Cable
Oscilloscope
PC
G Signal
Cut
ȃ3.5 plug for
32ǣ Dummy
from PC
Micro-
USB

Solder the ANT cable to the ANT terminal on the TX-RX unit.
J300

J200
GND

ANT

CN305

ϮPower supply cable (E37-1124-05) Power Supply +B

+B

Modify the cable as shown below. 3.8V -G

GND Q504

10ǹF/10V
+

Signal MIC
AG
Black
R238
AF VM
GND
MIG
Cut
Red IC201

Solder the power supply cable to the power supply terminal

on the TX-RX unit.
TX-RX Unit (Foil side view)

10
 PKT-03
ADJUSTMENT
Removing the Antenna Element from the Frequency and Signaling
TX-RX unit The transceiver has been adjusted for the frequencies
shown in the following table. When required, re-adjust them
1. Remove the solder of the two speaker lead wires (a). following the adjustment procedure to obtain the frequencies
2. Lift the TX-RX unit as shown in Fig. 1 (b). you want in actual operation.

b ■ Test Frequency (MHz)

Up line
TX-RX unit b CH RX Frequency TX Frequency
MIC
1 460.05000 460.10000
KEY TOP
2 440.05000 440.10000
3 479.95000 479.90000
4 459.80000 459.80000
b 5 460.00000 460.00000
6 460.20000 460.20000
7,8 - -

■ Signaling
a No. RX (Decode) TX (Encode)
Fig.1 1 None None
3. TX-RX unit is pulled out 1 cm (c). 2 QT 67.0Hz QT 67.0Hz
Note: All don't pull out Antenna.
3 QT 151.4Hz QT 151.4Hz
4 QT 210.7Hz QT 210.7Hz
5 QT 254.1Hz QT 254.1Hz
6 DQT D023N DQT D023N
7 DQT D754I DQT D754I
c
10mm

Preparations for Tuning the Transceiver

Before attempting to tune the transceiver, connect the
Fig.2 unit to a suitable power supply.
Whenever the transmitter is tuned, the unit must be con-
4. Remove the solder from the antenna element using a nected to a suitable dummy load (i.e. power meter).
soldering iron then pull out the TX-RX unit off (d). The speaker output connector must be terminated with a
Solder 32Ω dummy load and connected to an AC voltmeter and an
audio distortion meter or a SINAD measurement meter.

■ Adjustment frequency (MHz)

Tuning point RX TX
Low 440.05000 440.10000
Center 460.05000 460.10000
High 479.95000 479.90000
d

Fig.3

Note : Do not check High Transmit power in the state

where there is no frame.

11
PKT-03
ADJUSTMENT
Check Section
Measurement Adjustment
Item Condition Test- Specifications / Remarks
Unit Terminal Unit Parts Method
equipment
1. Setting 1) BATT terminal voltage: 3.8V TX-RX
2) SSG standard modulation

MOD: 1kHz, DEV: 1.5kHz

2. Frequency 1) Test Channel : 1 f. counter TX-RX ANT-JIG TX-RX FPU Check 440.100MHz ±2.5ppm
Signaling :1
TX Power : Low
Press [Transmit] button.

3. High 1) Test Channel : 1 Power Check 1.5W ±0.1W

Transmit Signaling :1 meter
Power TX Power : High Ammeter
∗Note 1 Press [Transmit] button.

4. Low 1) Test Channel : 1 0.5W ±0.1W

Transmit Signaling :1
Power TX Power : Low
Press [Transmit] button.

5. Maximum 1) Test Channel : 1 Deviation ANT-JIG TX-RX FPU 2.1kHz ±100Hz

Deviation Signaling :1 meter MIC-JIG (According to the larger +, –)
∗Note 2 TX Power : Low Power
Press [Transmit] button. meter
AG: 1kHz/100mV Oscilloscope
Deviation meter filter AG
LPF: 15kHz, HPF: OFF AF VM

6. MIC 1) Test Channel : 1 14mV ±5.0mV

Sensitivity Signaling :1
[Nomal] TX Power : Low
∗Note 2 Press [Transmit] button. Adjust AG input
AG: 1kHz to get a standard
Deviation meter filter MOD.
LPF: 15kHz, HPF: OFF

7. Sensitivity 1)SSG output: –118dBm SSG TX-RX ANT-JIG TX-RX FPU Check 12dB SINAD or more
(Receiver) (0.28µV) DVM EXT-
VOL position : "4" Oscilloscope Phone
AF VM
8.Squelch 1)SSG output: –118dBm Distortion Squelcgh : open
Level 1 (0.28µV) meter
Dummy
9.Squelch 1)SSG output: –128dBm load :32Ω Squelcgh : close
Level 1 (0.089µV)

∗Note 1: Do not check High Transmit power in the state where there is no frame.
∗Note 2: The microphone is always active. When you measure and adjust, please carry out in an environment without noise.
∗Note 3: The When you exchange charge IC (IC300) and a peripheral part, check that the voltage of TP1 is 3V to 4V.
(Setting from the USB connector to 5V power supply source)
TX-RX Unit (Component side view)

Power
Source
Micro- MIC

5V USB
TP1

(3-4V)

12
 PKT-03
ADJUSTMENT
Adjustment Section
Measurement Adjustment
Item Condition Test- Specifications / Remarks
Unit Terminal Unit Parts Method
equipment
1 High 1) Adj item: Low, Center, High Power TX-RX ANT-JIG FPU 1.5W ±0.1W
Transmit (3 points) meter 1.8A or less
Power and BATT terminal voltage: 3.8V Ammeter
Protective Press [Transmit] button.
Current
*Note
2. Low 1) Adj item: Low, Center, High 0.5W ±0.1W
Transmit (3 points) 1.0A or less
Power BATT terminal voltage: 3.8V
Press [Transmit] button.

3. Maximum 1) Adj item: Center, Low, High 2.1kHz ±100Hz

Deviation (3 points) (According to
[Narrow] AG: 1kHz/100mV the lager +, –)
Deviation meter filter
LPF: 15kHz
HPF: OFF
Press [Transmit] button.

4. Battery 1) BATT terminal voltage: 3.8V DVM TX-RX BATT FPU Write BATT terminal voltage: 3.8V
Reference terminal
Level

5. Battery 1) BATT terminal voltage: 3.1V DVM ANT Check LED blinks
Detection PTT: ON Power No transmit power
Check meter
(User mode) 2) BATT terminal voltage: 3.4V BATT LED does not blink
PTT: ON terminal

• It is not necessary to adjust the fixed values for the DQT-DEV, QT-DEV, MIC, and SQL sensitivity.

*Note: Do not adjust High Transmit power without connecting TX Power meter or 50 ohm dummy load to the ANT terminal.
Do not adjust High Transmit power in the state where there is no frame.

Power Supply JIG ANT Cable Note:

+B Lead Wire In order to adjust high power, as shown in a figure, please
-G Lead Wire (Red) attach a TX-RX unit to a frame.
(Black)

AG +
MIC

MIG

With out Antenna Element

FRAME

13
 A B C D E F G H I J

1 PKT-03 PC BOARD
TX-RX UNIT (X57-8490-22) Component side view (J79-0424-09)

F300
C317
CN302

R403 R404
4 3 Q205 1
3

C327
3 1
4

L200
1

C328 C323
R227
D301
IC301
R405 R239 4 6

C310
6 1
S6

R402 4 5

6 R233
D402 C217

R314
R234
F

R230

R226

CN306
Q206

TP1

S4
5
Q402 Q405
R82
R535 R10
C546

C550

R534 CN63

D300
R532 Q403

R8
C549 G G
D S Q507 Q404

R303
C542

C308
6 R531
R301
C536
R530

R6

S2
C552 R529

PTT

Q101
L512

S5

CN304
7 37 36
R9

48 25
IC3
8
S3

1 24
C20
C19

CN34 R302
+

R44 R313

R23
R22

CN61 12 13
R537
R342
R536

C229

1 X2
CN59 CN62 MIC1
9 3

10
J79-0424-09

Note : for service unit

11 A
B
440-480 MHz R541 C
R539 D
12

Component side Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address

Layer 1 IC3 8F Q101 6F Q402 5E Q405 5F D300 6H

Layer 2 IC301 4G Q205 4F Q403 6F Q507 6D D301 4G

13 Q206 5F Q404 6F D402 4E
Foil side

14
B C D E F G H I J

PC BOARD PKT-03 1

TX-RX UNIT (X57-8490-22) Foil side view (J79-0424-09)

2
EXT Phone
Micro USB

J300

VBUS
3
GND ５
N.C
D-
D+
1
GND ANT
J200

R333
R332

D405
D303

C543

C544
L515
4
C301
C319
3
+

R225
BATTRY
CN305

C531
R239

C541
L510 L513
T -

C214
R525 C535

C537
C551
D302

C558
1

C333 R334
C539

C559
D501

Q300
R524 C532
5

D502
C529 C533

C538
R526

CN303

CN314
+B
C528

L509
R528 C527 L511
L508

GND C524
C534
C523
C526

Q504

C519
C518
C517
TH500
C525

L505
6

C516 C515
L506
R520

CN307
R331 L504
R330

C350 R236

R527
C565
L507

R237 R241
R523

R522 C514
C513
R344

C349 R240 C530

R242
R517

C522 R518 C512

C521
CN310

5 1
R521

Q506

D201 R515 Q502

7

C557
IC300 Q208 Q207 C510
R514

R235
R512

C520
L503 C554
R83
R345

Q3
R516

L516
R513

6 10
R519

C563
C507
R3 R13

R21
R349

C351 R509
L517
R511

Q505 Q503 C9 C201 L502

R348
C200
R202

C562
C553
R213
R212

R18 R204
C548
C547

Q204 R507
CN232 C540 R200 R205 C555
C208

R238 C210 C218 R540 C556

Q200 8
R203 R206
R201 R207

C223 R218 R543

Q508

C210 R220 R229 Q501

R538
R222
C216
R223

R228 Q201
C14

IC2

4 1 R508
Q203
R32

R224 C506 C504 R505

C560 C500
C110
C109

IC200 C212 C13 C503

C15

C505
R506
L501
C12
C16

R216
C107
C108

CN231
C21
5 8 24
R219
C227
R215

25 16 9
C105

R217 C213 R221 C18

R79
C215 X1
R214 C220

C230
C209 1

C211

R61

IC100
C106

C23 R343
R60
8

C22

32 9
C221

C100
IC201

8
C101

1
C219

10
4

C103
C102

R231
R100

R232
R102
C104
J79-0424-09

R101

11
C225
C224

SP+ SP-

12

Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Component side
IC2 8F Q3 7F Q207 7E Q503 8E D201 7E D502 5G Layer 1
IC100 9G Q200 8E Q208 7E Q504 6F D202 5D Layer 2
IC200 9D Q201 8E Q300 5E Q505 7E D303 4D Foil side 13
IC201 10D Q203 9E Q501 8H Q506 7E D405 4G
IC300 7D Q204 8E Q502 7G Q508 8G D501 5G

15
 A B C D E

PKT-03
TX-RX UNIT (X57-8490-22)
SCHEMATIC DIAGRAM
PRE-DRIVE DRIVE
H : 0.9V R507 Q502
RFM01U7P C515 L505 C517 L5
L : 1.0V
2.2k
C553 L517 R544 C554 220p 2.2n 27p 1
CN307 CN310 CN314 2SC4926YD

L504
22n
C565
R527

C519
C518
4p

C516
47

27p
8p
10p
C500 C503 C504 8p 18n 0 18p
R505

4.7n
Q501

L503
+B

C563
C562

10p
12p
470p 8p 33p 22 H : 1.2V

L502
22n
L : 0.9V

R509
3.3k
R506

C514
C560

C513
C505
L501

470p
1k

0.1u
12n
4p

4p

R515

C522
100k
R518
22k
C506 470p

C512
R512

R513
100k

0.1u
R508 470

15k
R538 27

470p
C507

R511
10
R : 0V
T : 3.2V

33T

470p
C555

470p
0.1u

C556

C510

R520
39k
R543

47k
H : 0V
L : 3.2V H : 1.4V

R516
Q508 L : 1.0V

R519
47k

330
R540
R521

R514
270p
3.3k

C547
0.1u

C548

18k

TH500

100k
C525
470p
DISCHG SW

-t
DC SW 47k
(Hi/Lo) S S M 6 N 1 7 F U Q503 Q505

P_TEMP
H/L

470p
C520
470p
C540

CURRENT
DC SW
(Hi/Lo)

LTC014EEBFS8
LTC014EEBFS8

33MC
IC2
BU4827F
3 NC 3.3V
VDD
2
330k
C14
R32

1u

2SK1824-A
Q101
4 GND DC SW
VoUT 1
C12
1u
RESET
470p
C13

TRANSCEIVER
33M SYSTEM
36
35
34
33
32
31
30
29
28
27
26
25

SQIN
3.3V
R83

H/L
PTT
FNC

UP

IC100
LIGHT

CHG

DCSW
DOWN

POWER

EPDET

33MC

QTIN
33TC/T/R
0

37

R102

32

31

30

29

28

27

26
R101
P_TEMP N.C

10k
24

10k
DC SW 38

GPIo0

GPIo1

GPIo2

GPIo3

GPIo4

GPIo5

GPIo6
CURRENT N.C
R13 23
Q3 39 1
BATT USB_DPUPE
3.8V SSM6L36TU-F 15k 22 AVDD1
40 SCLK 2
470p

VOICE_DATA USB_VCC
R18

21 SCLK
39k

R3
C9

41 SDIO 3
RED MCU USB_DP SDIo
47k 20 VSS
42
R22

4
47k

GREEN USB_DM AVSS

IC3 AVDD2

R100
19

47k
43 F21348UKEZA 5
BLUE USB_VBUS XTAL1
18
44 6
TYPE2 MIC_MUTE XTAL2
17
45
R21

7
47k

E2PWP MIC_ATT MoDE

16
46 8

MIC_IN
470p
TYPE1

AVDD3
470p
ATT2

AFoUT
0.1u

0.1u
E2PIN SENB
15

RFIN
NC1
47

NC2
+B

CC
ATT1
VCC/AVCC
VSS/AVSS

C100

SCLK
14
SP_MUTE

48
RESET

9
SDIO

10

11

12
13

14

15
C101

R82 C102

C103
MoDE
TRWP

VREF

13
XOUT
SQIN

QTIN
PDN

XIN

0
47k
47k
47k
47k

POWER
10
11
12
1
2
3
4
5
6
7
8
9

S3 33M

470p
22u

0.1u
R6

R10
R9
R8

TRWP
3.3V
0.1u

4.7k
470p
C19

C107
C20

S2 PTT

C106
C105
C104
R44

X2
12.0MHz

S4 R537
UP
47k
+B

S5 DOWN 33M

R212
470p

0.1u
C21

C16

10u
C15
100k
R536

S6 FNC MODE RESET

C208
3.3V
VDD GND TCXO
0.01u
470p

0.1u
C22

C18
C23

1 GND1
VCC
4
2 GND2 R61
oUTPUT 3 560
3.8V
R60

X1
10k

25.6MHz
R402

R404
150

R405
100

R403
270

47

LIGHT
INDICATOR LED
D402

C R541
LED
D405
LIGHT

0
LED ON : 3.3V
LED ON : 3.3V
BLUE

R202 R204 R205 R201

LTC023JEBFS8

R200
LTC023JEBFS8
LTC023JEBFS8
LTC023JEBFS8

330 220 0 10k

Q402

Q404

Q403

0
Q405

R206
R203

270
560
R207
3.3k
C200

0.1u

C201

0.1u

LED ON : 3.3V Q200 Q201

GREEN
RED DC SW DC SW
(RED) (WHITE) LTC014EEBFS8
DC SW DC SW
LED ON : 3.3V LTC014EEB
(BLUE) (GREEN)

16
X57-849 1/2
 F G H I J

SCHEMATIC DIAGRAM PKT-03

L513 L515 ANT

FINAL ANT SW 4T 4T
R FM0 3 U 3 C T L509 C532 C558 D501 C535 C539 C543
Q504 3.9n 15p 180p 180p

2. 5p (B)
L506 RN142S 1 .5 p 1p

C537

C541
C52 9

C544
C528
L508
C524

8p
27p

15p

3p
330n
3T

5p

L510
R517 L507
1.5n

120 220n
C51 9

27p

H : 1.4V
L : 1.0V

C526

C523

0. 01u
470p
0. 1u

C521

470p
C522
100k

R525
R518

470p
C531

120
R : 0V
T : 3.2V

33T

C551

470p
DC SW
(CURRENT)
Q506
SSM6 L 3 6 TU -F
R528
R526
R524
0. 3 9

0. 39
0. 3 9

R521 33M
R : 0V
47k T : 0.8V
+B L511 ANT SW
470p
C534

4T
R523

RN142S
C538
C533

D502
6p

6p
470p
C530

15k
R522
CURRENT

3 9k

3.8V
PC CONECT : 5.0V
PC NO CONECT : 0V
R302 µ-USB
J 300
1 .5 k R 3 0 3

68k R314 F300

VBUS
USB_DPUPE R313 27 1A 1
D-

DZ2J062(M)
USB_VBUS 27 2

R301
120k

D300
D+

C308

1u

C317
USB_DM 3

1u
CHG N.C
USB_DP 4
GND
D301 5
RSB12JS2 +B
R345
IC 3 0 0 8 .2 k

C350
470p
SQIN BQ24086DRCR

R331
4 .7 u
C349

1 .5 k
CHARGE ON : 0.02V BATT CHG KNB-71L
FULL CHARGE : 5.0V 1 IN SYSTEM CN305
R343 oUT 10
POWER ON : 0.04V
29

28

27

26

25

2 TMR + 3
0 BAT 9
G P I o4

G P I o5

G P I o6

G P I o7

3 STAT1 T 2
TS 8
R332
R342 3.3V

R348
R344

C351
4 STAT2 - 1

47k

2 .2 u
56k
R330
56k
PD N 24

CN306
PG 7

1k
R529

AVD D 6 0 5 VSS
47

23
C546

R333 IS E T 6
0 .1 u

PABI AS
S 22
DA2J101
82k

R349
SS
100k

R534
R532

100k

820
C552

470p

AVDD 5 TP1
D303

21
270n
L512

NC 5 IC 3 0 1
20
NC 4 1.3V BU33TD3WG
19 C536 R530 3.2V
1 3.3V
PC CONECT : 3.0V
470p
C327

C328

R F o UT VIN V oUT
1u

18 470p 22 C550 POWER ON : 3.0V 5

2 G ND
A V DD3

C110
A V DD4

470p

NC 3

470p
C 1 09

C323

C310
0 .1 u

17 RF AMP Q5 0 7 3
RF I N

1u
NC2

3SK318 470p STBY NC

4
R : 0.27V
T : 0.23V
13

14

15
16

C301

C319
470p

3.3V AVR
C549
R531

470p

1u
R535
C542

470p

68k

D302
47

DAN222WM
33M
470p
22u

0 .1 u

470p

33T
0 .1 u

R : 0V
C108
C107

T : 3.2V
C106
C105

33M 3.3V
R334
100k

Q300
SSM3J36TUT
POWER
DC SW
C3 3 3

47 0 p

(33T)
C 224

+B 4 70p INT SP
R 21 2
470

C2 1 0 C216 C218 SP+

R213 R218 R220 R222
1.8k 10k 47k 2.2k AF POWER IC 2 0 1 AF AMP ON : 2.0V
0.1u 1u 1u
C2 08

10 u

AMP NJU7089KV1
R 223

R2 24
82 0

1k

1 AF AMP ON : 2.0V SP-

SD
4

N JM 134 0 4R B 1

C220 oUT B 8
470 p
C225

2
A oU T
GN D

A+ IN

A- IN

BYPASS
MIC/BPF MIC SENS 1u G ND 7 C221
R2 41
R2 3 5

R 23 6

3
2 2k
47 k

22k

AMP SW +IN
AF AMP
V+ 6
R231 4 10u
MUTE
I C2 00

-IN
B oU T
B +IN

oUT A 5
B -IN

C 2 09 10k
V+

0. 2 2u
C 21 9

Q2 0 3 2SK1824-A
R232
D A N2 22 W M

0 . 1u Q208
5

LTC014EEBFS8 39k R240 EXT PHONE

R 2 14 R217
100 J200
4 70p
C2 15

R2 42
C 21 3

0. 1 u

4 7 k (D)
1 00k

4 7 k(D) AF AMP ON : 2.2V

D2 01

AF AMP OFF : 0V

R237
100
C211 R215 R219 R221 C214
47k 47k 0 R234
R2 3 9

1u 22u
R2 27

1 0k
C 22 9

R 225
4 7p

47k

15

C212 R216 C227 47k

SP MUTE
1u 47k 470p Q207
R2 06
27 0

Q205
C2 30

LTC014EEBFS8 LTC014EEBFS8
47 p

MTM76520
R 23 3

AF ON : 3.3V Q206
47 0k

SP MUTE
201 AF OFF : 0V C217 INT MIC
0 .0 2 2 u
R226 R230
4 70 p
C2 23

SP MUTE
1k 470k
R238
C 0 1 4 EEBFS8 M I C1
0

17
X57-849 2/2
18
Receiver Section Transmitter Section
ƷTo make measurements in the AF section, connect the AC level meter. ƷAG is set to the MIC input becomes 1.5kHz Dev, at 1kHz MOD. (Narrow)
(ANT input: –53dBm,1kHz FM, 1.5kHz Dev .) ƷTo make measurements in the AF section, connect the AC level meter.
ƷIn the RF section, use a high impedance probe. (ANT input: –53dBm, MOD off). ƷIn the RF section, use a 1000pF coupling capacitor.
ƷVolume position (EXT PHONE :”4” ,INT SP :”6”)
PKT-03

RF (CENTER FREQUENCY) AF (1kHz)

X57-8490-22

93.8mVrms
J200
EPDET
EXT PHONE:107mVrms
IC100 INT SP:193mVrms EXT PHONE
INT SP:189mVrms (32ǣ)
1.37Vrms
IC200(B/2) Q205 IC200
C211 C214 C219 AF POW
9 AF AF
AF OUT AMP INT SP
-53dBm (RX) -47.5dBm -41dBm AMP MUTE
TRANSCEIVER SYSTEM (BTL) (4ǣ)
Q507

C550 C536 15 Q200 Q201 D201 Q208

440-480MHz RF AMP RF IN
AF AF AMP
ATT1 ATT2 SP_MUT OR MUTE

+31.7dBm (TX) +28.4dBm +15.8dBm +9.5dBm +6.0dBm MIC SENC N:11.8mVrms 14.4mVrms
Q504 Q502 Q501 ATT1 ATT2 MIC SENC H:17.9mVrms IC200(A/2)

C558 C517 C553 C500 11 C218 C218

FINAL DRIVE 18 MIC
ANT SW PRE-DRIVE RF OUT MIC_IN INT MIC
AMP AMP AMP AMP
Q203
D501,502 DVDD
33T MIC
33M AVDD MIC_ATT ATT
33T Q506 Q503 Q508 J300

+B DC SW DC SW DC SW XTAL
CURRENT H/L H/L 5 32 26 2 3 8 24 D- MICRO
X1
-USB
D+
Q505 TCXO
TRWP
PDN

SDIO

SCLK

QT IN
33M
SQ IN
H/L 33M
33M 25.6MHz VBUS
DISCHG
DISCSW IC300
SW
Q101
Q300
POWER1 33M POWER CHG CHARAG
S3 33M DC SW CN305
+B 33T DC SW POWER1
33TC
TS
PTT
Q3 IC3
S2
+B
BATT MCU
F21348UKEZA KNB-71L
+B DC SW
D303
UP
S4 +B +B +B +B
BLUE RED
BLOCK & LEVEL DIAGRAM

GREEN OR
VBUS
IC301
Q402 Q403 Q404 Q405
DOWN PTT,UP,DOWN,FNC,EPDET
S5 AVR
CHG,VBUS,D+,D-,CURRENT D302
DC SW DC SW DC SW DC SW LIGHT (33M)
(BLE) (RED) (GRN) (WHT)
33MC
FNC OR
S6 X2 POWER1
D402 D405 LIGHT,GREEN,RED,BULE,33TC,33MC,H/L 12MHz 33M
DISCSW,ATT1,ATT2,MIC_ATT,SP_MUT
 PKT-03
OPTIONAL ACCESSORIES
KNB-71L (Li-ion Battery Pack) ■ Specifications
■ External View
Nominal Voltage .................................................... 3.7V
Nominal Capacity ................................................. 1430mAh

Note:
The ambient temperature should be between 0°C and 40°C
while charging is in progress.
Charging outside this range may not fully charge the battery.

REPLACING THE BATTERY PACK

Replace an expired battery pack with a newly purchased KNB-71L battery pack.

Do not disassemble the battery pack.

Be sure to follow local laws concerning the disposal of battery packs.

1 Using a #1 size Phillips screwdriver, remove the 4 screws, then lift the back panel (FIG.1).
2 Remove the packing containing the old battery pack from the transceiver (FIG.2).
s Lift the battery pack cable and remove the connector from the PCB terminal (FIG.2).
3 Remove the old battery pack from the packing and insert the new battery pack.
s Pass the battery pack cable through the hole in the packing (FIG.3).
s Attach it so that the 4 points are on the battery pack (FIG.3).
4 Insert the connector of the new battery pack into the PCB terminal by pressing down on it,
then lay the battery pack into position (FIG.4).
s Match the direction of the connector and insert it vertically (FIG.4).
s Wire the battery pack cable (FIG.5) and route it around the packing (FIG.6).
s Confirm the routing of the cable (FIG.5) with the 4 points of the packing (FIG.3).
5 Place the back panel over the battery pack and connect it using the 4 screws.
FIG.1 FIG.2 FIG.3

Packing

FIG.4 FIG.5 FIG.6

Red Right

Wrong

19
PKT-03
SPECIFICATIONS
General
Operation Frequency Range ................................ 440~480MHz
Number of Channels ............................................ Max. 4
Channel Spacing .................................................. 12.5kHz
PLL Channel Stepping ......................................... 5kHz, 6.25kHz
Operating Voltage .................................................. 3.8V DC (3.4V-4.2V)
Battery Life ............................................................ More than 14 hours at 1.5 watts (5-5-90 duty cycle. Battery save : ON)
Operating Temperature Range ............................. –10°C to +60°C
Frequency Stability ............................................... ±2.5ppm
Channel Frequency Spread .................................. 40MHz
Dimensions and Weight (Dimensions not including protrusions)
....................................................................... 46 W x 85 H x 20 D mm , 100g (W/Battery)

Receiver (Measurements made per TIA/EIA-603)

Sensitivity
EIA 12dB SINAD .............................................0.22µV
Selectivity .............................................................60dB
Intermodulation Distortion ....................................50dB
Audio Output .........................................................300mW at 4Ω (INT Speaker.VOL position : "6")
0.1mW at 32Ω (EXT Phone. VOL position : "4")

Transmitter (Measurements made per TIA/EIA-603)

RF Output Power ................................................. 1.5W/0.5W
Spurious Response ............................................. 55dB
Modulation ........................................................... 11K0F3E
FM Hum & Noise ................................................. 50dB
Modulation Distortion ........................................... Less than 5%

Measurements made per TIA/EIA-603 and specifications shown are typical.

JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
 A B C D E F G H I J

TX-RX UNIT (X57-8490-22)

L513 L515 ANT
1
FINAL ANT SW 4T 4T
RFM0 3 U3 CT L509 C5 3 2 C5 5 8 D5 0 1 C5 3 5 C5 3 9 C5 4 3
PRE-DRIVE DRIVE
Q504 3.9n
H : 0.9V R507 Q 502 15p 180p 180p 1.5p 1p

2 . 5 p (B)
C5 1 5 L 5 0 5 C5 1 7 L506 RN1 4 2 S
L : 1.0V RFM 01U7 P

C5 3 7

C5 4 1
2. 2k

C5 2 9

C5 4 4
C5 2 8
L508
C5 2 4

8p
27p

15p

3p
330n
3T
2.2n 27p

5p
1.5n

L510
R5 1 7 L 5 0 7
120 220n
C N 307 C N 310 C N 314 2SC4926YD C553 L517 R544 C554 220p

L504
22n
C5 6 5
R5 2 7

C5 1 9
C5 1 8
4p

C5 1 6
47

27p
8p
18n

10p
C500 C503 C504 R505 8p 0 18p

4.7n
Q 501

L503
+B H : 1.4V

C5 6 3
C5 6 2
22 H : 1.2V

10p
33p

12p
470p 8p L : 1.0V

L5 0 2
L : 0.9V

22 n
R50 9
3. 3 k
R50 6

C514
C560

C513
C505
L501

470p
1k

0. 1u
12n

C526

C523

0. 01u
4p

4p

470p
0. 1u

C521

470p
R515

C522
100k

R525
R518
22k

470p
C531
C506 470p

120
C512
R512

R513
100k

0. 1u
R508 470

15k
R538 27

470p
R : 0V

C507

R511
10
R : 0V T : 3.2V
T : 3.2V

33T 33T

470p
C555

470p
0. 1u

C556

C510

C551

470p
2

R520
DC SW

39k
R543
(CURRENT)

47k
H : 0V
L : 3.2V H : 1.4V
L : 1.0V Q506

R516
Q 508

R519
47k

330
S S M6 L 3 6 TU-F

R528
R540

R526
R524
0. 39

0. 39
0. 39
3. 3k R5 2 1 33M

R514
270p
C547
0. 1u

C548
R : 0V

18k

TH500
DISCHG SW

100k
C525
470p
47k T : 0.8V

-t
DC SW L511 ANT SW
Q503 Q505 +B
(Hi/Lo) SSM 6N17FU

470p
C534
4T

P_TEMP
H/L R5 2 3

RN142S
C538
C533

D502
470p

6p

6p
470p
C520
470p

C530
15k

C540

R522
CURRENT
DC SW

39k
(Hi/Lo)

LTC014EEBFS8
LTC014EEBFS8 3.8V
PC CONECT : 5.0V
PC NO CONECT : 0V

33MC
R3 0 2 µ-USB
IC 2 J300
1 . 5 k R3 0 3
B U 4827F
3.3V 68k R3 1 4 F300
3 NC
VDD
2
VBUS 3
R3 1 3 2 7 1A 1
330k
C14

USB_DPUPE
R32

2SK1824- A
1u

D-
Q 101 27

DZ2J062( M )
USB_VBUS 2
4 GN D

R301
120k
DC SW D+

D300
C308
V oU T 1

1u
USB_DM 3

C317
C 12

1u
1u CHG N.C
USB_DP 4
RESET GND
D3 0 1 5
470p
C13

RS B 1 2 J S2 +B
R345
TRANSCEIVER
33M SYSTEM I C3 0 0 8.2k
36
35
34
33
32
31
30
29
28
27
26
25
SQIN BQ24086DRCR

C350
470p

R331
4. 7u
C349
3.3V

1. 5k
CHARGE ON : 0.02V BATT CHG KNB-71L
R83

I C1 0 0

H/L
PTT
FNC

UP

1 IN
LIGHT
QTIN

CHG

DCSW
DOWN

POWER

EPDET

33MC
FULL CHARGE : 5.0V SYSTEM C N3 0 5

33TC/T/R
0

37 R3 4 3 oUT 10
POWER ON : 0.04V
P_TEMP N.C 2 TMR

R102
+

32

31

30

29

28

27

26

25
R101
24 3

10k

10k
DC SW 38 0 BAT 9

GP Io0

GP Io1

GP Io2

GP Io3

GP Io4

GP Io5

GP Io6

GP Io7
CURRENT N.C 3 S TA T 1 T 2
R 13 23 TS 8
Q3 39 1
R3 4 2 3.3V

R332
BATT U S B _D P U P E 4 S TA T 2 -

R348
1

R344

C351
S S M6L36TU -F 22

47k
3.8V

2. 2u
56k
R330
15k PDN 24

56k
AVDD1 PG 7
40

CN306
1k
SCLK 2 0

R529
VOICE_DATA U S B _V C C AVDD6 5 VSS
470p

21 SCL K
R18
39k

R3 23

47
I SET 6
C9

41

C546
R3 3 3

0. 1u
MCU SDIO 3
RED U S B _D P SDI o PABI AS
20 VSS 22
47k 82k
4

DA2J101
42 4
R22

AVSS
47k

R349
100k

R534
R532

100k
GREEN U S B _D M

820
TP1

C552
IC 3 19 AVDD2 AVDD5

470p
R100

D303
21

47k
43 5

270n
L512
F21348U K E ZA
BLUE U S B _V B U S XT AL 1 NC5
18 20 I C3 0 1
44 6 1.3V B U3 3 TD 3 W G
TYPE2 MIC_MUTE XT AL 2 NC4
17 19 C5 3 6 R5 3 0 3.2V
45 7 3.3V
R21

1
47k

MIC_ATT PC CONECT : 3.0V

470p
E2PWP

C327

C328
16 M o DE RF o UT 22 VI N Vo UT

1u
46
18 470p C5 5 0 POWER ON : 3.0V 2 G ND 5
TYPE1 8

MIC _IN
470p
ATT2

AVDD3
470p
E2PIN NC3

C110
AVDD4
A FoU T
0. 1u

0. 1u

470p
SENB

470p
15

C109
RF AMP Q507

C323

C310
0. 1u
17 3

R FIN

1u
47 470p

NC1
+B ST BY NC

NC2
ATT1 3SK318

CC
4
V C C /A V C C

SCLK
V S S /A V S S

C100
14 R : 0.27V
SP_MUTE

48 SDIO T : 0.23V
RESET

10

11

12
13

14

15
16
R 82

C101
13

C301
3.3V AVR

C319
C102

C103
MoD E
TRWP

VREF

470p
XOUT
SQIN

QTIN

C549
R531

470p
PDN

1u
R535
C542

470p
D3 0 2
XIN

68k
0

47
47k
47k
47k
47k

POWER DA N2 2 2 WM
10
11
12
1
2
3
4
5
6
7
8
9

S3 33M 33M

470p
22u

0. 1u
R6

R10
R9
R8

TRWP
3.3V 33T R : 0V

470p

0. 1u
C108
0. 1u

4. 7k
470p
C19

C107
C20

T : 3.2V
S2 PTT

C106
C105
C104
X2 33M 3.3V
R44

12. 0M Hz

R334
100k
Q300
R 537 S S M3 J 3 6 TUT
S4 UP POWER
47k DC SW 5

C333

470p
+B
(33T)

C224

470p
S5 DOWN 33M
+B INT SP

R2 1 2
470
470p

0.1u
C21

C1 6

10u
C1 5

SP+
100k

C2 1 0 C2 1 6 C2 1 8
R5 3 6

S6 R2 1 3 R2 1 8 R2 2 0 R2 2 2
FNC MODE RESET
1.8k 10k 47k 2.2k AF POWER I C2 0 1 AF AMP ON : 2.0V
0.1u 1u 1u

C2 0 8
AMP

10u
NJ U7 0 8 9 K V 1

R2 2 3

R2 2 4
3.3V

820

1k
TCXO 1 AF AMP ON : 2.0V SP-
VDD GND SD

N JM1 3 4 0 4 R B 1
C2 2 0 o UT B 8

0.01u
470p

0.1u

470p
C2 2

2
C1 8
C23

C2 25
A oU T
G ND

A+ I N

A- I N
1 G ND1 BYPASS
VCC MIC/BPF MIC SENS 1u G ND 7 C2 2 1

R241
3

R235

R2 3 6
4

22k
47k

22k
AMP SW +IN
AF AMP
R6 1 V+ 6
2 G ND2 R2 3 1 4 10u
MUTE

I C2 0 0
o UT PUT -IN
3

B o UT
o UT A 5

B+IN
560 10k

B-IN
3.8V C2 0 9

V+
X1 2 S K 1 8 2 4 -A

0 .2 2 u
C219
R6 0

Q203
10k

R2 3 2

D AN 2 2 2 WM
2 5 . 6 MHz 0.1u Q208

8
R2 4 0 EXT PHONE
R402

L TC0 1 4 E E B FS 8 39k
R404
150

R2 1 4 R2 1 7
R4 0 5
100

R4 0 3
270

J200
47

100
6

470p
4 7 k (D)

C2 1 5
4 7 k(D)

R242
C2 1 3
AF AMP ON : 2.2V

0.1u

100k

D201
AF AMP OFF : 0V
LIGHT R237
INDICATOR LED
C R 541 100
D4 0 2

LED
D4 0 5
LIGHT

0 C2 1 1 R2 1 5 R2 1 9 R2 2 1 C2 1 4
LED ON : 3.3V
LED ON : 3.3V 47k 47k R2 3 4
1u 0 22u

R2 3 9
R2 2 7

10k
C2 2 9
BLUE

R2 2 5
47p

47k

15
R200 R2 0 2 R2 0 4 R2 0 5 R2 0 1 C2 1 2 R2 1 6 C2 2 7 47k
L T C0 2 3 J E BF S 8
L TC0 2 3 J E B FS 8

SP MUTE
L T C0 2 3 J E BF S 8
L T C0 2 3 J E B FS 8

330 220 0 0 10k 1u 47k 470p Q207

Q4 0 2

Q4 0 4

Q4 0 3

Q405

R2 0 6
R2 0 3

Q205
270
560
R2 0 7

C230
L TC0 1 4 E E B FS 8 L TC0 1 4 E E B FS 8
3 .3 k
C2 0 0

0.1u

C2 0 1

0.1u

47p
AF ON : 3.3V MTM7 6 5 2 0 Q206

R2 3 3
SP MUTE

470k
LED ON : 3.3V Q200 Q201 AF OFF : 0V C2 1 7 INT MIC
0.022u
GREEN
R2 2 6 R2 3 0
SP MUTE

470p
C2 2 3
RED DC SW DC SW 1k 470k
(RED) (WHITE) L TC0 1 4 E E B FS 8
DC SW DC SW R238
LED ON : 3.3V L TC0 1 4 E E B FS 8 M I C1
(BLUE) (GREEN) 0