UNIT I ELECTRICAL CIRCUITS ANALYSIS Important Questions

UNIT I ELECTRICAL CIRCUITS ANALYSIS
important questions
1. What is meant by charge?
Charge is an electrical property of the atomic particles which matter
consists. The charge of an electron is so small. Charge in motion
represents current. The unit of charge is coulomb.
2. What is meant by Current?

The flow of free electrons in a conductor is called current. Unit is
ampere (A). I =Q/t
3. What is meant by Voltage?
The poterntial difference between two points is called as voltage. Unit

is Volts (V). V=W/Q , W=work done in joules & Q = charge in coulombs
4. State Ohm’s Law.
The potential difference across any two ends of a conductor is directly

proportional to the current flowing between the two ends provided the
temperature of the conductor remains constant.
5. State Krichoff’s Voltage Law

KVL states that the algebraic sum of voltages in a closed path is
zero.
6. State Krichoff’s current Law.
KCL states that the algebraic sum of currents in a node is zero.
7. Give short notes on resistor.
It is a property of a substance3 which opposes the flow of electrons. It is
denoted by R and its unit is Ohm
8. Distinguish between a Branch and a node of a circuit.
A pair of network which connects the various points of the network is
called branch A point at which two or more elements are joined together
is called node.
9. Distinguish between a mesh and a loop of a circuit.
A mesh is a loop that does not contain other loops. All meshes are loop,
but all loops are not meshes. A loop is any closed path of branches
10. Write down the formula for a star connected network is converted into a
delta network?
RA=( R1 R2)/( R1 +R2+ R3) RB=( R1 R3)/( R1 +R2+ R3)
RC=( R2 R3)/( R1 +R2+ R3)
11. Write down the formula for a delta connected network is converted
into a star network?
R1=( RARB+RBRC+RCRA)/RC R2=( RARB+RBRC+RCRA)/RB R3=(
RARB+RBRC+RCRA)/RA
12. Define line currents and phase currents?
The currents flowing in the lines are called as line currents The currents
flowing through phase are called phase currents
13. Define line voltage and phase voltage?
The voltage across one phase and neutral is called line voltage & the
voltage between two lines is called phase voltage
14. Give the phase value & Line value of a star connected system.
VL= 3Vph
15. Give the phase value and line valued of a delta connected system.
IL= 3Iph
16. What is the power equation for a star connected system?
P= 3I V cosΦ L L W
17. What is the power equation for a delta connected system?
P= 3I V cosΦ L L W
18. What is meant by Real power?

Real power means the useful power transfer from source to load. Unit is
watts.
19. What is meant by apparent power?

Apparent power is the product of voltage and current and it is not true power.
Unit is VA
20. What is reactive power?
If we consider the circuit as purely inductive the output power is
reactive power. Its unit is VAR
21. Define Instrument.
Instrument is defined as a device for determining the value or magnitude
of a quantity or variable.
22. Mention the two main differences between an ammeter and a voltmeter.
Ammeter Voltmeter
It is a current measuring device it is a voltage measuring device
Always connected in series with circuit Always connected in parallel with
circuit
The resistance is very small The resistance is very high
23. What is control system?
A system consists of a number of components connected together to
perform a specific function . In a system when the output quantity is controlled
by varying the input quantity then the system is called control system.
24. What are the two major types of control system?
The two major types of control system are open loop and closed loop
25. Define open loop control system.
The control system in which the output quantity has no effect upon the
input quantity are called open loop control system. This means that the output is
not feedback to the input for correction.
26. .Define closed loop control system.
The control system in which the output has an effect upon the input
quantity so as to maintain the desired output value are called closed loop control
system
27. Mention the errors in Moving iron instruments.
Hysteresis error
Temperature error
Stray magnetic field error
Frequency error
Eddy current error
28. Mention any two precautions to be taken while using an Ammeter.

It should never be connected across any source. The polarity must be
observed correctly.
First use the highest range and then decrease the voltage range until the
sufficient deflection is obtained.
29. Define Form factor and Crest factor.
Form factor= RMS value / Average Value
Crest(peak) factor=Maximum Value / RMS value
30. Which type of instrument is called as universal instrument?

The moving iron instrument are known as universal instruments, because
these instruments can be used for AC and DC.
31. What are the applications of MI instruments?
i) Used as multirange ammeters and voltmeters.
ii) Used as in expensive indicators such as charging and discharging
current indicators in automobiles.
iii)Extensively used in industries for measurement of AC voltage and
current where errors of the order of 5% to 10% are accepetable.
32. What is meant by eddy current damping?
When the conductor moves in a magnetic field an emf is induced in it and
if a closed path is provided ,a current flows known as eddy current. This current
intersect with the magnetic field to produce an electromagnetic torque , which
opposes the deflecting torque.
33. How is electrical power measured?
i) Using Voltmeter-ammeter method for DC circuits. ii)Using Watt
meters for AC circuits.
34. What do you mean by compensation coil in a wattmeter?
By connecting a compensating coil in series with a pressure coil, The
error caused by the pressure coil flowing in the current coil can be neutralized.
35. What are the three types of power used in a a.c circuit?
35. Define averagevalue.

The average value of an alternating current is that value of steady direct
current which transfers the same charge as the alternating current flowing for
the same time.
37. Define RMS value.

The effective value of an alternating current is that value of steady ,direct
current which produces the same heat as that produced by the alternating current
when passed which produces the same heat as that produced by the alternating
current when passed through the same resistance for the same interval of time.
38. Define reactive power.

The power consumed by a pure reactance (XL or Xc ) in a a.c circuit is called
reactive power.

UNIT I ELECTRICAL CIRCUITS ANALYSIS Important Questions

Uploaded by

Copyright:

Available Formats

UNIT I ELECTRICAL CIRCUITS ANALYSIS Important Questions

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

UNIT I ELECTRICAL CIRCUITS ANALYSIS Important Questions

Uploaded by

Copyright:

Available Formats

UNIT I ELECTRICAL CIRCUITS ANALYSIS

2. What is meant by Current?

3. What is meant by Voltage?

The poterntial difference between two points is called as voltage. Unit

4. State Ohm’s Law.

The potential difference across any two ends of a conductor is directly

5. State Krichoff’s Voltage Law

18. What is meant by Real power?

19. What is meant by apparent power?

28. Mention any two precautions to be taken while using an Ammeter.

Crest(peak) factor=Maximum Value / RMS value

30. Which type of instrument is called as universal instrument?

35. Define averagevalue.

37. Define RMS value.

38. Define reactive power.

You might also like