D. NO LIQUID, GAS OR VAPOR, EXCEPT WATER NOT EXCEEDING 30 DEG. C NOR 0.30 C.

GROUT
GENERAL NOTES ON EXCAVATION MPa PRESSURE, SHALL BE PLACED IN THE PIPES UNTIL THE CONCRETE HAS AT-
TAINED ITS DESIGN STRENGTH. 1. THE WATER, AGGREGATE AND CEMENT RATIO SHALL BE CONTROLLED SO THAT WHEN MIXED
A. CONTRACTOR SHALL ENSURE THAT ALL EXISTING STRUCTURES ARE PROPERLY AND THOROUGHLY ( FOR NOT LESS THAN 10 MINUTES) A FLUID CONSISTENCY WILL RESULT.
THE GENERAL NOTES AND SPECIAL REQUIREMENTS ARE SUPPLEMENTAL TO AND FORM
ADEQUATELY SUPPORTED AGAINST SETTLEMENT OR MOVEMENT DURING EXCAVATION ADMIXTURE MAY BE USED IN THE GROUT MIXED ONLY IF IT HAS BEEN DETERMINED BY
PART OF THE PLANS, DRAWINGS AND SPECIFICATIONS WHERE OR REQUIREMENTS ARE E. EXCEPT WHEN DRAWINGS FOR CONDUITS AND PIPES ARE APPROVED BY THE DESIGNER
CONDUITS AND PIPES EMBEDDED WITHIN SLAB, WALL OR BEAM ( OTHER THAN THOSE AUTHORITATIVE TESTS THAT WILL NOT DECREASE ITS STRENGTH OF BOND.
NOT COVERED BY THE PLANS OR SPECIFICATIONS. THESE GENERAL CONSTRUCTION
B. CONTRACTOR SHALL ENSURE THAT EXCAVATION PIT ARE FREE FROM WATER TABLE
NOTES SHALL BE USED INSOFAR AS THEY ARE APPLICABLE TO SATISFY REQUIREMENTS MERELY PASSING THROUGH ) SHALL SATISFY THE FOLOWING;
AND ADEQUATE DEWATERING SYSTEM MUST BE AVAILABLE DURING EXCAVATION WORK. 2. FOR SOLID MASONRY, ALL INSIDE SPACES SHALL BE FILLED WITH GROUT AND SHALL ENCASE
OF GOOD CONTRUCTION PRACTICE. IN CASE OF QUESTIONS ARISING FROM THE INTER-
1. THEY SHALL NOT BE LARGER IN OUTSIDE DIMENSION THAN 1/3 THE OVERALL FULLY THE REINFORCING STEEL, IF ANY. IN CASE OF PILASTER OR COLUMN CONSTRUCTION,
PRETATION OF OR COMPLICT WITH OTHER DOCUMENTS. THE ATTENTION OF THE OWNER
NOTES ON COMPACTED FILL GROUTING SHALL BE DONE IN LAYERS THAT WILL ASSURE PROPER FILLING OF ALL VOIDS AND
ENGINEERS MUST BE CALLED IN WRITING. THICKNESS OF SLAB , WALL OR BEAM IN WHICH THEY ARE EMBEDDED.
KEYED PROPERLY TO PREVENT SLIPPAGE OF BOND.
A. FILL AND SUBGRADES UNDER SLABS AND FOOTINGS SHALL BE COMPACTED TO A
2. THEY SHALL NOT BE SPACED CLOSER THAN 3 DIAMETER OR WIDTH ON CENTER.
MINIMUM 95% OF MAXIMUM DRY DENSITY BASED ON ASTM D-698
GENERAL NOTES 3. THEY SHALL NOT IMPAIR SIGNIFICANTLY THE STRENGTH OF CONSTRUCTION.
D. JOINTS
B. MAXIMUM LIFT THICKNESS FOR COMPACTION SHALL BE 250mm.
A. 1. MOVING UNITS AFTER PLACING. MASONRY UNITS SHALL NOT BE MOVED AFTER THEY HAVE
BEEN CONTACT WITH THE MORTAR. TAPPING UNITS DOWNWARD MAY BE PERMISSIBLE BUT NOT
WITH MINIMUM STRENGTH OF fy = 227.50 Mpa ( 33,000 psi )
C. MONITOR QUALITY OF COMPACTION USING AN INDEPENDENT TESTING LABORATORY
USE ASTM D - 1558 PROCEDURE. TYPICAL BAR BENDING, HOOK AND SPLICING TO ROCK OR SLID THEM.

B. TYPICAL BENDING, HOOKS AND SPLICING FOR REINFORCEMENT SHALL BE SHOWN IN DETAIL - 1 2. JOINTING NEW AND OLD WORK. INTERSECTION OF NEW AND OLD WORK SHALL BE ADEQUATELY
NOTES ON SLAB GRADE 12d BONDED AND DOWELED TO PROVIDE CONTINUITY OF THE MASONRY.
A. SUBGRADE SHALL BE COMPACTED BY MECHANICAL OR MANUAL COMPACTOR TO A D
C. IN THE INTERPRETATION OF DRAWINGS INDICATED DIMENSIONS SHALL GOVERN AND D 3. SET, THE EXPOSED SURFACE OF THE FINISHED MASONRY SHALL BE CLEANED AND DAMPENED
MINIMUM 90% OF MAXIMUM DRY DENSITY. BAR SIZE 90deg. 180deg.
DISTANCES OR SIZES SHALL NOT BE SCALED FOR CONTRUCTION PURPOSES. D HOOK HOOK AS NECESSARY TO OBTAIN THE BEST POSSIBLE BOND WITH THE NEW WORK. ALL LOOSED
THRU MASONRY UNITS AND MORTAR SHALL BE REMOVED. CONSTRUCTION JOINTS SHALL NOT BE
B. PROVIDE MAXIMUM 2.0 M. SPACING BETWEEN CONSTRUCTION OR CONTRACTION JOINT. 4d (64MM MIN.)
D. IN REFERENCE TO OTHER DRAWINGS, SEE ARCHITECTURAL DRAWING FOR DEPRES - d 6d 5d PERMITTED IN ANY BEAM, UNLESS APPROVED BY ENGINEER.
d
SIONS IN FLOOR SLAB, OPENING IN WALLS AND SLAB PARTITIONS, LOCATION OF THRU
C. CONTINUOUS WET CURING OF CONCRETE BY POUNDING SHALL BE DONE FOR AT 8d 5d
DRAINS, ETC.
LEAST 14 DAYS. E. ARCHES AND LINTEL
E. IN CASE OF DISCREPANCIES AS TO THE LAYOUT DIMENSIONS AND ELEVATIONS d = BAR DIAMETER
BETWEEN THE STRUCTURAL PLANS AND OTHER DRAWINGS, THE CONTRACTOR SHALL NOTES ON CONCRETE PROTECTION FOR REINFORCEMENT 90 DEG. HOOK 180 DEG. HOOK D = BEND DIAMETER 1. THE MASONRY WALL OPENING SUCH AS DOORS AND WINDOWS AND TOP OF WALL WITHOUT
BEAM SHALL BE PROVIDED BY LINTEL BEAM AS SHOWN IN DETAIL 2
NOTIFY BOTH THE STRUCTURAL ENGINEERS AND THE OWNER REPRESENTATIVE OR
A. THE FOLLOWING MINIMUM CONCRETE COVER SHALL BE PROVIDED FOR REINFORCEMENT; NOTES:
SITE ENGINEERS IN WRITING BEFORE PROCEEDING WITH THE AFFECTED WORK. 1. ALL BENDS SHOWN ON DETAILS/SCHEDULES SHALL BE STANDARD
2. 180DEG. HOOKS MAY BE SUBSTITUTED FOR 90 DEG. HOOKS
1. CONCRETE PERMANENTLY EXPOSED TO EARTH ---------- 75mm
NOTES ON CONCRETE MIXES AND PLACING
2. CONCRETE EXPOSED TO EARTH OR WEATHER TIE HOOK A
A. THE CONTRACTOR SHALL SUBMIT THE SCHEDULE OF POURING AND LOCATIONS AT 20mm THROUGH 36mm BARS -------------------- 50mm D = 4d S 1
CONSTRUCTION JOINTS TO THE CONSTRUCTION MANAGEMENT AT LEAST FOUR (4) DAYS 16mm AND SMALLER ------------------------- 40mm
PRIOR TO THE POURING FOR APPROVAL
3. CONCRETE NOT EXPOSED TO WEATHER OR IN CONTACT WITH GROUND 40d (600MM MIN.)
B. WET CURING OF CONCRETE SHALL BE CONTINUOUS FOR MINIMUM PERIOD OF TEN d 6 (MIN.)
SLABS, WALLS AND JOIST ----------------------- 20mm 1
(10) DAYS IMMEDIATELY AFTER POURING. d
BEAMS AND COLUMNS ------------------------- 40mm WIRE TIGHTLY
TOGETHER LAP SPLICE
C. THE CONTRACTOR SHALL FURNISH AND MAINTAIN ADEQUATE FORMS FOR SHORINGS OFFSET
UNTIL THE CONCRETE MEMBERS HAVE ATTAINED THEIR SUFFICIENT STRENGTH FOR
THE WORKING CONDITION ANTICIPATED.
NOTES ON SPACING LIMITS FOR REINFORCEMENT
DETAIL OF STIRRUP
A. THE MINIMUM CLEAR SPACING BETWEEN PARALLEL BARS IN A LAYER BE BAR DIA- AND CLOSING BAR
D. ALL CONCRETE WORKS SHALL BE DONE IN ACCORDANCE WITH THE ACI 318-83 METER, BUT NOT LESS THAN 25mm. ANCHORAGE DIMENSION
BUILDING CODE REQUIREMENTS FOR REINFORCED CONCRETE AND ALL STRUCTURAL
STEEL WORK IN ACCORDANCE WITH THE LATEST EDITION OF A.I.S.C SPECIFICATIONS B. WHERE PARALLEL REINFORCEMENT IS PLACED IN TWO LAYERS, BARS IN THE UPPER
IN SO FAR AS THEY DO NOT COMPLICT WITH THE REQUIREMENTS OF THE NATIONAL LAYERS SHALL BE PLACED DIRECTLY ABOVE BARS IN THE BOTTOM LAYER WITH DOOR OR WINDOW OPENING
STRUCTURAL CODE FOR BUILDING AND LOCAL CODES CLEAR DISTANCE BETWEEN LAYERS NOT LESS THAN 25mm.
1 TYPICAL BENDING DETAIL FOR REINF. STEEL
E. A.C.I REFERS TO AMERICAN CONCRETE INSTITUTE. A.I.S.C TO AMERICAN INTITUTE OF C. IN SPIRALLY OR TIED REINFORCED COMPRESSION MEMBERS CLEAR DISTANCE BET- S 1 NOT TO SCALE
STEEL CONSTRUCTION AND A.S.T.M TO AMERICAN SOCIETY FOR TESTING MATERIALS WEEN LONGITUDINAL BARS SHALL BE NOT LESS THAN 1.5 BAR DIAMETER NOR 40mm.

F. UNLESS OTHERWISE INDICATED IN THE PLANS OR NOTED IN THE SPECIFICATION, THE D. CLEAR DISTANCE LIMITATION BETWEEN BARS SHALL APPLY ALSO TO THE CLEAR WALL ELEVATION
MINIMUM 28th DAY CYLINDER COMPRESSIVE STRENGTH OF CONCRETE SHALL BE DISTANCE BETWEEN A CONTACT TAP SPLICE AND ADJACENT SPLICES OR BARS.
AS FOLLOWS;

1. COLUMN AND WALL FOOTING

E. IN WALLS AND SLABS, PRIMARY FLEXURAL REINFORCEMENT SHALL BE SPACED NOT
FARTHER APART THAN THREE TIMES THE WALL OR SLAB THICKNESS, NOR 450mm.
NOTES ON STRUCTURAL STEEL
fc' = 20.70 MPa ( 3,000 psi ) A. MATERIALS:
2. BEAMS AND GIRDERS NOTES ON CONSTRUCTION JOINT 1. STRUCTURAL STEEL - STEEL TO BE USED FOR FABRICATION AND ERECTION OF
TRUSS STRUCTURE SHALL COMPLY WITH ALL THE PERTIMENT PROVISIONS OF NSCP
fc' = 20.70 MPa ( 3,000 psi )
A. SURFACE OF CONCRETE CONSTRUCTION JOINTS SHALL BE CLEANED AND LAITANCE SPECIFICATION
3. COLUMN REMOVED.
fc' = 20.70 MPa ( 3,000 psi ) a) ALL MATERIALS FOR FABRICATION OF STEEL RAFTER SHALL A36
B. IMMEDIATELY BEFORE NEW CONCRETE IS PLACED, ALL CONSTRUCTION JOINTS SHALL b) BOLTS
4. LINTEL BEAMS, SLAB ON GRADE AND CATCH BASINS
BE WETTED AND STANDING WATER REMOVED. ALL BOLTS NUTS AND WASHERS SHALL CONFORM TO ASTM A307 OR A325
fc' = 20.70 MPa ( 3,00 psi )
UNLESS OTHERWISE INDICATED. ANCHOR BOLTS SHALL LIKEWISE BE OF
C. CONSTRUCTION JOINTS IN FLOORS SHALL BE LOCATED WITHIN THE MIDDLE THIRD EQUAL STRENGTH AS ASTM A325 BOLT OF THE SAME SIZE. CHB WALL
G 1. CONCRETE SHALL BE DEPOSITED IN ITS FINAL POSITION WITHOUT SEGREGATION OF SPANS OF SLABS, BEAMS AND GIRDERS. JOINT IN GIRDERS SHALL BE OFFSET
RE-HANDLING OR FLOWING. PLACING SHALL BE DONE PREFERABLY WITH BUGGIES A MINIMUM DISTANCE OF TWO TIMES THE WIDTH OF INTERSECTING BEAMS. B. FABRICATION:
BUCKETS OR WHEELBARROWS. NO CHUTE WILL BE ALLOWED EXCEPT TO TRANSFER
CONCRETE FROM HOPPERS TO BUGGIES, WHEELBARROWS OR BUCKETS IN WHICH D. BEAMS, GIRDERS, OR SLABS SUPPORTED BY COLUMNS OR WALLS SHALL NOT BE a) MINIMUM EDGE DISTANCE:
CASE THEY SHALL NOT EXCEED SIX ( 6 ) METERS IN AGGREGATE LENGTH. THE MINIMUM EDGE DISTANCE OF BOLTS SHALL CONFORM TO THE REQUIRE- CONCRETE
CAST OR ERECTED UNTIL CONCRETE IN THE VERTICAL SUPPORT MEMBERS IS NO
LONGER PLASTIC. MENTS OF AISC STEEL MANUAL 8th EDITION.
2. NO DEPOSITING OF CONCRETE SHALL BE ALLOWED WITHOUT THE USE OF VIBRA- THE MAXIMUM EDGE DISTANCE FROM BOLT CENTER SHALL BE 12 TIMES
TORS UNLESS AUTHORIZED IN WRITING BY THE DESIGNER AND ONLY FOR UN-
USUAL CONDITIONS WHERE VIBRATION IS EXTREMELY DIFFICULT TO ACCOMPLISH.
NOTES ON REMOVAL OF FORMS AND SHORES b)
THICKNESS OF THE PLATE BUT NOT TO EXCEED 150mm.
MINIMUM PITCH;
A. FORMS SHALL BE REMOVED IN SUCH MANNER AS NOT TO IMPAIR SAFETY AND ON CENTER SPACING OF BOLTS SHALL NOT BE LESS THAN THREE (3) TIMES
3. SAMPLING FOR COMPRESSIVE STRENGTH TEST SHALL BE MADE IN ACCORDANCE SERVICEABILITY OF THE STRUCTURE. ALL CONCRETE TO BE EXPOSED BY FORM THE NOMINAL DIAMETER.
WITH SPECIFICATIONS BUT SHALL BE NOT LESS THAN ONE (1) SET FOR EACH DAY OF REMOVAL SHALL HAVE SUFFICIENT STRENGTH NOT TO BE DAMAGED THEREBY.
POUR.
B. NO CONSTRUCTION LOADS EXCEEDING THE COMBINATION OF SUPERIMPOSED DEAD NOTES ON MASONRY UNITS SECTION - A

NOTES ON FOOTING LOAD PLUS SPECIFIED LIVE LOAD SHALL BE SUPPORTED ON ANY UNSHORED POR-
TION OF THE STRUCTURE UNDER CONSTRUCTION, UNLESS ANALYSIS INDICATES A MATERIALS
ADEQUATE STRENGTH TO SUPPORT SUCH ADDITIONAL LOADS.
A. CONTRACTOR SHALL REPORT TO THE SITE INSPECTOR THE ACTUAL UNUSUAL SOIL 1. THE QUALITY AND DESIGN OF MATERIALS ASSEMBLED IN MASONRY WORK SHALL CONFORM WITH
CONDITIONS UNCOVERED AND CONFIRM ACTUAL BEARING CAPACITY OF SOIL IN
NOTES ON EMBEDDED CONDUITS AND PIPES ON CONCRETE NATIONAL STRUCTURAL CODE OF THE PHILIPPINES.
WRITING BEFORE DEPOSITING CONCRETE.
A. CONDUITS AND PILES OF ALUMINUM SHALL NOT BE EMBEDED IN STRUCTURAL 2. UNLESS OTHERWISE INDICATED IN THE PLANS OR NOTED IN THE SPECIFICATION THE MINIMUM 2 TYPICAL LINTEL BEAM DETAIL
B. FOOTING SHALL REST AT LEAST 0.90 M. BELOW NATURAL GRADE LINE UNLESS 28th DAYS CYLINDER COMPRESSIVE STRENGTH OF CONCRETE SHALL BE 375 psi S 1 NOT TO SCALE
CONCRETE UNLESS EFFECTIVELY COATED OR COVERED TO PREVENT ALUMINUM -
OTHERWISE INDICATED.
CONCRETE REACTION OR ELECTROLYTIC ACTION BETWEEN ALUMINUM AND STEEL.
B REINFORCEMENT
C. UNLESS OTHERWISE SPECIFIED ALL FOOTINGS SHALL REST ON DENSE SAND/HARD
B. CONDUITS, PIPES AND SLEEVES PASSING THROUGH A SLAB, WALL, OR BEAM SHALL
CLAY. THIS SOMETIMES REQUIRE OVER EXCAVATION OF ABOUT 1.00 M. FROM
NOT IMPAIR SIGNIFICANTLY THE STRENGTH OF THE CONSTRUCTION. 1. ALL REINFORCEMENT SHALL BE FREE FROM COATINGS THAT WOULD DESTROY OR REDUCE BOND.
PRESCRIBED BOUNDARY LEVEL. SUCH OVER EXCAVATION SHALL BE REPLACED WITH
WELL COMPACTED CRUSHED ROCK BACKFILL. COMPACTION SHALL BE 95% OF MDD
C. CONDUITS, PIPES WITH THEIR FITTINGS, EMBEDDED WITHIN A COLUMN SHALL NOT 2. THE SIZE AND SPACING OF REINFORCEMENT FOR EVERY ASSEMBLED MASONRY STRUCTURE
DISPLACE MORE THAN FOUR (4) PERCENT OF THE AREA OF THE CROSS SECTION
D. FOOTING WERE DESIGNED USING A GROSS ALLOWABLE SOIL BEARING CAPACITY OF
ON WHICH STRENGTH IS CALCULATED. HORIZONTAL BAR.
95.76KPa (2,000 psf) AT REQUIRED DEPTH.

ARCHITECT R.A. 9266 SEC. 33 CIVIL ENGINEER PROJECT TITLE APPROVED REVISION SHEET CONTENTS SHEET NUMBER

DRAWINGS AND SPECIFICATIONS AND OTHER CONTRACT DOCUMENTS

DULY SIGNED, STAMPED OR SEALED, AS INSTRUMENTS OF SERVICE,
PROPOSED TWO (2) STOREY
DATE
1
ARE THE INTELLECTUAL PROPERTY AND DOCUMENTS OF THE
DATE
SHERWIN N. NIEVA, uap ARCHITECT, WHETHER THE OBJECT FOR WHICH THEY ARE MADE IS RICHMON B. PANGILINAN RESIDENCE
PRC NO. 0014850 PTR NO.
EXECUTED OR NOT. IT SHALL BE UNLAWFUL FOR ANY PERSON TO
DUPLICATE OR TO MAKE COPIES OF SAID DOCUMENTS FOR USE IN THE PRC NO.: 116730 PTR NO.: MR. & MRS. CHARLES M. MANZANERO DATE
GENERAL NOTES S 3
REPETITION OF AND FOR OTHER PROJECTS OR BUILDINGS, WHETHER
VALIDITY JULY 07, 2015 DATE EXECUTED PARTLY OR IN WHOLE, WITHOUT THE WRITTEN CONSENT VALIDITY: MAY 13, 2016 DATE:
OF THE ARCHITECT OR AUTHOR OF THE SAID DOCUMENTS. LOCATION: ILAWOD, CAMALIG, ALBAY OWNER DATE DATE: JANUARY 2015
TIN 915-805-923 PLACE TIN: 411-996-576 PLACE:
 1 2 3 4 1 2 3 4 1 2 3 4
CONTINUOUS

WF - 2
@ 50mm; 3 @ 100mm
REST @ 150mm O.C

WF - 2
ROOF EAVES LINE DS ROOF LINE DS DS

SERVICE ELEV. @ CONCRETE CANOPY LINE

0.60m CONTINUOUS
AREA C1-F1 C1-F1
FTB FTB FTB B-1 B-1 B-1 RB - 1 RB - 1 RB - 1
C1-F1

C1-F1
SECTION AT SUPPORT
A A A DS DS

HT - 4

HT - 4
WF - 1 WF - 1 WF - 1 BUILDING LINE

WF - 1
100mm THK.
WF - 2

T&B
ELEV. @ ELEV. @ CONCRETE SLAB
S-2

WF - 1
0.60m 0.60m GUEST
BAR, SAG ROD

WF - 1
WF - 1

B-1
KITCHEN

B-1
ROOM
FTB

FTB

FTB
SPACED @ 250mm

HT - 1
S-2

B-1
B-1

RB - 1
ELEV. @ WF - 3 ELEV. @ S-2 B-2 O.C. BOTHWAYS

RB - 1
WF - 1
0.625m ELEV. @ 0.625m
HT - 4 HT - 4

-1
H
0.625m S-1

PT

PT
FTB FTB FTB B-1 B-1

-1
C1-F1

C1-F1

H
B B B CONTINUOUS

CONCRETE CANOPY LINE

WF - 1

RB - 1
WF - 1 WF - 1 S-2 B-1

B-2

ROOF LINE

ROOF LINE
WF - 1

WF - 2 @ 50mm; 3 @ 100mm

WF - 1
B-2 STAIR

BUILDING LINE

BUILDING LINE
FTB

FTB

FTB
FTB

B-1
ELEV. @

B-1
S-2

B-1

RB - 1
DINING 0.625m WELL FT - 1 REST @ 150mm O.C
ELEV. @

ROOF EAVES LINE

S-2

ROOF EAVES LINE

0.625m
FT - 1 BOTTOM BAR
FTB FTB FTB

C1-F1
C1-F2

C C B-1 B-1 B-1 C DS DS

2"X4"X1.5mm

B-1
ELEV. @ 100mm THK. CONCRETE
WF - 1

0.625m C-PURLINS CONTINUOUS

FTB

SLAB ON FILL WITH 10mm

S-2 S-2 SPACED @
SECTION AT MIDSPAN

-2
600mm O.C

RB - 1
B-1
400mm O.C. BOTHWAYS

PT

RB - 1
B-1
WF - 1

H
C1-F2

B-1
LIVING
FTB
FTB

FTB HT - 4

PT
OPEN
D D D

H
100mm THK.

HT - 1
ELEV. @

-1
B-1 B-1 BELOW CONCRETE CANOPY
WF - 2 0.625m B-1

B-1

H
HT - 2
FTB

PT
WF - 2 S-2 S-2 SPACED @ 200mm

HT - 4
-3
O.C. BOTHWAYS, HT - 3
WF - 1 TYPICAL RB - 1
C1-F2

E FTB FTB FTB

E B-1 B-1
E DS DS

B-1

RB - 1

RB - 1
BUILDING LINE

H
-3
C1-F1 PORCH C1-F1 C1-F1

PT
WF - 2

HT - 2
B-1
CARPORT

PT
FTB

-3
ELEV. @ S-2 CONTINUOUS

H
ELEV. @ 0.60m
0.10m ROOF EAVES LINE RB - 1 DS ROOF LINE DS

B-1
B-1
FTB

F F F
C2

WF - 2 B-1
C2-F3 100mm THK. CONCRETE ROOF LINE @ 50mm; 3 @ 100mm
FTB

REST @ 150mm O.C

REBAR SPACED @
S-2 250mm O.C. CONTINUOUS
G FTB
G G
B-1 SECTION AT SUPPORT
C2-F3 C2-F3

CONTINUOUS

@ 50mm; 3 @ 100mm
REST @ 150mm O.C

BOTTOM BAR

CONTINUOUS

SECTION AT MIDSPAN

1 2 3 4 B-2

CONTINUOUS

BAR

@ 50mm; 3 @ 100mm
REST @ 150mm O.C

CONTINUOUS

SECTION AT SUPPORT

CONTINUOUS

@ 50mm; 3 @ 100mm
4 @ 100MM REST @ 150MM 0.C. 4 @ 100MM REST @ 150MM 0.C. 4 @ 100MM REST @ 150MM 0.C. REST @ 150mm O.C

BOTTOM BAR
- CONTINUOUS - CONTINUOUS - CONTINUOUS

CONTINUOUS
BOTTOM BARS- CONTINUOUS BOTTOM BARS- CONTINUOUS BOTTOM BARS- CONTINUOUS
SECTION AT MIDSPAN

TRANSVERSE SECTION
RB - 1

ARCHITECT R.A. 9266 SEC. 33 CIVIL ENGINEER PROJECT TITLE APPROVED REVISION SHEET CONTENTS SHEET NUMBER

DRAWINGS AND SPECIFICATIONS AND OTHER CONTRACT DOCUMENTS

DULY SIGNED, STAMPED OR SEALED, AS INSTRUMENTS OF SERVICE,
PROPOSED TWO (2) STOREY
DATE FOUNDATION PLAN 2
ARE THE INTELLECTUAL PROPERTY AND DOCUMENTS OF THE SECOND FLOOR FRAMING PLAN
DATE
SHERWIN N. NIEVA, uap ARCHITECT, WHETHER THE OBJECT FOR WHICH THEY ARE MADE IS RICHMON B. PANGILINAN RESIDENCE ROOF FRAMING PLAN
PRC NO. 0014850 PTR NO.
EXECUTED OR NOT. IT SHALL BE UNLAWFUL FOR ANY PERSON TO
DUPLICATE OR TO MAKE COPIES OF SAID DOCUMENTS FOR USE IN THE PRC NO.: 116730 PTR NO.: MR. & MRS. CHARLES M. MANZANERO DATE
BEAM TRANSVERSE DETAIL S 3
REPETITION OF AND FOR OTHER PROJECTS OR BUILDINGS, WHETHER BEAM DETAIL
VALIDITY JULY 07, 2015 DATE EXECUTED PARTLY OR IN WHOLE, WITHOUT THE WRITTEN CONSENT VALIDITY: MAY 13, 2016 DATE:
OF THE ARCHITECT OR AUTHOR OF THE SAID DOCUMENTS. LOCATION: ILAWOD, CAMALIG, ALBAY OWNER DATE DATE: JANUARY 2015
TIN 915-805-923 PLACE TIN: 411-996-576 PLACE:
 @ EVERY 3 LAYERS @ EVERY 3 LAYERS
REINFORCEMENT STEEL
REINFORCEMENT STEEL @ 0.80 m OC
SPACED, 3 @ 50mm, 3@ FFL @ 0.80 m OC FFL @ 0.80 m OC
SPACED, 3 @ 50mm, 3@ 100mm REST @ 150mm
100mm REST @ 150mm
COLUMN AT NGL 100mm THK. GRAVEL NGL 100mm THK. GRAVEL @ EVERY 3 LAYERS
COLUMN AT 2ND FLR. BED BED
2ND FLR. 150 mm THK. CHB 100 mm THK. CHB

150 mm THK. CHB

BARS @ 300mm O.C & FFL
BARS @ 300mm O.C &
BARS
BARS
FOOTING TIE BEAM
100MM THICK GRAVEL
6 - 16mm TEMPERATURE 100MM THICK GRAVEL
BED
6 - 16mm TEMPERATURE BARS O.C. BOTHWAYS 5 - 12mm TEMPERATURE 100MM THICK GRAVEL BED
BARS O.C. BOTHWAYS (SPACE AS SHOWN) BARS O.C BOTHWAYS BED
(SPACE AS SHOWN) (SPACE AS SHOWN) WF - 2
WF - 1 WF - 3
REINFORCEMENT STEEL REINFORCEMENT STEEL REINFORCEMENT
BAR BAR
TIES SPACED, 3 @ 50mm, 3@
REINFORCEMENT STEEL REINFORCEMENT STEEL 100mm REST @ 150mm

SPACED, 3 @ 50mm, 3@ SPACED, 3 @ 50mm, 3@

100mm REST @ 150mm 100mm REST @ 150mm PLAN 4
PLAN TOP OF
PLAN CONTINUOUS
LANDING

@ 50mm; 3 @ 100mm
REST @ 150mm O.C

BAR - CONTINUOUS 0.30m .O.C

CONTINUOUS 0.30m .O.C

REINFORCEMENT STEEL REINFORCEMENT STEEL
NGL BAR NGL BAR NGL
SECTION AT SUPPORT
0.300m. O.C DOUBLE
LAYER
REINFORCEMENT STEEL REINFORCEMENT STEEL REINFORCEMENT
GRND FLR.
SPACED, 3 @ 50mm, 3@ SPACED, 3 @ 50mm, 3@ TIES SPACED, 3 @ 50mm, FINISH LINE
100mm REST @ 150mm 100mm REST @ 150mm 3@ 100mm REST @ 150mm
O.C

CONTINUOUS

6 - 16mm TEMPERATURE 6 - 16mm TEMPERATURE 5 - 12mm TEMPERATURE

BARS O.C BOTHWAYS BARS O.C BOTHWAYS BARS O.C BOTHWAYS BAR - CONTINUOUS
(SPACE AS SHOWN) (SPACE AS SHOWN) (SPACE AS SHOWN)
@ 50mm; 3 @ 100mm
REST @ 150mm O.C

CONTINUOUS
SECTION SECTION SECTION

C1 - F1 C1 - F2 C2 - F3 SECTION AT MIDSPAN

GAUGE 24 GI RIDGE ROLL,

PRE-PAINTED

FT - 1 ( 2 SETS ) HT - 3 ( 1 SET )
GAUGE 26 APO TILE SPAN
ROOFING, PRE-PAINTED
E 2-
GL 2"
x2
AN "x
mm 4.5
300MM x 3/4" FIBER CEMENT
x 4.5 BA mm 50MM x 100MM x 1.5MM
2" R R AN
FASCIA BOARD, PAINTED
"x BA G C-PURLINS SPACED AT EVERY
2 -2 LE
600MM O.C.
2-
2 - 2" x 2" x 4.5mm ANGLE BAR

GLE 2"
AN x2
1"X1" ANGLE BAR FRAMING, "x
mm 4.5
WELDED 4.5 BA mm
"x R R AN
" x 2 BA GL
-2 E
2 - 2" x 2" x 4.5mm ANGLE BAR

2 - 2" x 2" x 4.5mm ANGLE BAR

2
2-

AR

6" METAL SPANDREL, ON 1"X2"

E 2-
2"

EB

GL 2" METAL FURRINGS SPACED @

AN x2
x2

"x 600mm O.C BOTHWAYS,

GL
2 - 2" x 2" x 4.5mm ANGLE

2 - 2" x 2" x 4.5mm ANGLE

mm 4.5
"x

4.5 PRE-PAINTED
AN

"x R BA mm
4.5
2

LE

x 2 BA R A HT - 1 ( 2 SETS ) HT - 2 ( 2 SETS )
NG HT - 4 ( 6 SETS )
m
-2

2"
NG

L
mm

.5m

2- E
"x

R mA
2" BA

x4
AN
BAR

BAR
BA .5m
x4 R
2 - 2" x 2" x 4.5mm

2 - 2" x 2" x 4.5mm

GL

2"

2-
.5

E 2-
4
ANGLE BAR

ANGLE BAR

GL 300MM x 3/4" FIBER CEMENT

x
EB

m 2"
m

2"
AN .5m x2
2"
m

2"

AN x 2 "x FASCIA BOARD ON 1"X1" ANGLE

mm x4 R
AR
AN

2-

GL " x
"x

4.5 4.5
x E 4.5 2" BA BA mm
BAR FRAMING, PAINTED
GL

-2

2" R x E
x BA BA m 2" GL R AN
E

TOP OF 2" R m 2 - AN GL
2- E
GAUGE 24 SPANISH STYLE
BEAM GUTTER, PRE-PAINTED
2 - 2" x 2" x 4.5mm ANGLE BAR 2 - 2" x 2" x 4.5mm ANGLE BAR

PAINTED FINISH

10mm METAL PLATE HPT - 3 ( 2 SETS )

HPT - 3 ( 1 SET )
HPT - 3 ( 3 SETS )

ARCHITECT R.A. 9266 SEC. 33 CIVIL ENGINEER PROJECT TITLE APPROVED REVISION SHEET CONTENTS SHEET NUMBER

DRAWINGS AND SPECIFICATIONS AND OTHER CONTRACT DOCUMENTS

DULY SIGNED, STAMPED OR SEALED, AS INSTRUMENTS OF SERVICE,
PROPOSED TWO (2) STOREY
DATE COLUMN/FOOTING DETAIL
WALL FOOTING DETAIL
3
ARE THE INTELLECTUAL PROPERTY AND DOCUMENTS OF THE
DATE
SHERWIN N. NIEVA, uap ARCHITECT, WHETHER THE OBJECT FOR WHICH THEY ARE MADE IS RICHMON B. PANGILINAN RESIDENCE FOOTING-TIE BEAM DETAIL

PRC NO. 0014850 PTR NO.

EXECUTED OR NOT. IT SHALL BE UNLAWFUL FOR ANY PERSON TO
DUPLICATE OR TO MAKE COPIES OF SAID DOCUMENTS FOR USE IN THE PRC NO.: 116730 PTR NO.: MR. & MRS. CHARLES M. MANZANERO DATE
STAIR DETAIL SECTION S 3
REPETITION OF AND FOR OTHER PROJECTS OR BUILDINGS, WHETHER TRUSS DETAIL
VALIDITY JULY 07, 2015 DATE EXECUTED PARTLY OR IN WHOLE, WITHOUT THE WRITTEN CONSENT VALIDITY: MAY 13, 2016 DATE: TRUSS DIAGRAM
OF THE ARCHITECT OR AUTHOR OF THE SAID DOCUMENTS. LOCATION: ILAWOD, CAMALIG, ALBAY OWNER DATE DATE: JANUARY 2015
TIN 915-805-923 PLACE TIN: 411-996-576 PLACE: