Scribd
Upload
17 views8 pages

ECE212L - Group#12 - Experiment 7

The document is a laboratory report on the characteristics of a BJT transistor in common emitter configuration. It includes procedures and results for measuring the input characteristics by varying the base-emitter voltage VBE and measuring base current IB at different collector-emitter voltages VCE. It also details measuring the output characteristics by varying the collector-emitter voltage VCE and measuring collector current IC at different fixed base currents IB. Tables of measured data and graphs of the input and output characteristics are presented.

Uploaded by

eliverivan1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
17 views8 pages

ECE212L - Group#12 - Experiment 7

The document is a laboratory report on the characteristics of a BJT transistor in common emitter configuration. It includes procedures and results for measuring the input characteristics by varying the base-emitter voltage VBE and measuring base current IB at different collector-emitter voltages VCE. It also details measuring the output characteristics by varying the collector-emitter voltage VCE and measuring collector current IC at different fixed base currents IB. Tables of measured data and graphs of the input and output characteristics are presented.

Uploaded by

eliverivan1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

NEW ERA UNIVERSITY

No.9 Central Avenue, New Era, Quezon City, 1107 Metro Manila
College of Engineering and Architecture

LABORATORY REPORT IN
ELECTRONIC CIRCUIT AND DEVICES

Eliver Ivan De Leon


Shan Clynt Bado
Experiment No:7

Characteristics of a BJT in Common Emitter Configuration

Components:

Specifications:
For Transistor BC 107:
Max Collector Current= 0.1A
VCEO max= 50V
Procedure:
Input Characteristics:
1) Connect the circuit as shown in fig.(1). Adjust all
the knobs of the power supply to their minimum
positions before switching the supply on.
2) Adjust the VCE to 0 V by adjusting the supply
VCC.
3) Vary the supply voltage VBB so that VBE varies in
steps of 0.1 V from 0 to 0.5 V and then in steps
of 0.02 V from 0.5 to 0.7 V. In each step note the
value of base current IB.
4) Adjust VCE to 1, 2V and repeat step-3 for each
value of VCE.
5) Plot a graph between VBE and IB for different
values of VCE. These curves are called input
characteristics
:
Input Characteristics: Output Characteristics:
VCE = 0 VCE = 1 VCE = 2 IB = 20μA IB = 40μA IB = 60μA
VCE IC -1 IC -2 IC -3
VBE IB VCE = 0 IB VCE = 1 IB VCE = 2
0 0.000118 0.000184 0.000240464
0 0 0 0
0.2 0.005811 0.01157 0.016971487
0.1 1.04E-10 1E-10 9.99368E-11
0.4 0.005898 0.011796 0.017370245
0.2 2.87E-10 2.1E-10 2.09857E-10
0.6 0.005913 0.01182 0.017415171
0.3 2.09E-09 4.46E-10 4.4597E-10
0.8 0.005927 0.011848 0.01745418
0.4 3.85E-08 2.64E-09 2.64313E-09
1 0.005941 0.011876 0.017495766
0.5 8.35E-07 4.08E-08 4.08068E-08
1.2 0.005956 0.011905 0.01753733
0.52 1.54E-06 7.47E-08 7.46934E-08
1.4 0.005971 0.011933 0.017578873
0.54 2.79E-06 1.39E-07 1.38802E-07
1.6 0.005985 0.011961 0.017620394
0.56 4.93E-06 2.62E-07 2.61532E-07
1.8 0.006 0.01199 0.017661892
0.58 8.39E-06 4.98E-07 4.98422E-07
2 0.006014 0.012018 0.017703369
0.6 1.36E-05 9.56E-07 9.56021E-07
3 0.006087 0.01216 0.017910407
0.62 2.06E-05 1.83E-06 1.82863E-06
4 0.006159 0.012301 0.018116938
0.64 2.96E-05 3.44E-06 3.43478E-06
5 0.006231 0.012442 0.018322909
0.66 4.03E-05 6.21E-06 6.20995E-06
6 0.006303 0.012583 0.018528339
0.68 5.23E-05 1.06E-05 1.05699E-05
7 0.006375 0.012723 0.018733232
0.7 6.55E-05 1.68E-05 1.67375E-05
8 0.006447 0.012863 0.01893759
0.72 2.47E-05 2.46643E-05
9 0.006519 0.013003 0.019141415
0.74 3.42E-05 3.41252E-05
10 0.00659 0.013142 0.019344709
0.76 4.49E-05 4.48244E-05
0.78 5.66E-05
0.8 6.92E-05
Procedure:
Output Characteristics:
1) Connect the circuit as shown in fig. (2). All the
knobs of the power supply must be at the
minimum position before the supply is switched on.
2) Adjust the base current IB to 20 μA by adjusting
the supply VBB.
3) Vary the supply voltage VCC so that the voltage
VCE varies in steps of 0.2 V from 0 to 2 V and then
in steps of 1 V from 2 to 10 V. In each step the base
current should be adjusted to the present value
and the collector current IC should be recorded.
4) Adjust the base current at 40, 60 μA and repeat
step-3 for each value of IB.
5) Plot a graph between the output voltage VCE and
output current IC for different values of the input
current IB. These curves are called the output
characteristics.
Output Characteristics:

VBE
0.709125 IB = 20μA 2.00E-05
0.751962 IB = 40μA 4.00E-05
0.78666 IB = 60μA 6.00E-05

You might also like