TA78L005AP ToshibaSemiconductor

Download as pdf or txt
Download as pdf or txt
You are on page 1of 22

TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP

TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic


TA78L005AP, TA78L006AP, TA78L007AP, TA78L075AP, TA78L008AP,
TA78L009AP, TA78L010AP, TA78L012AP, TA78L132AP,
TA78L015AP, TA78L018AP, TA78L020AP, TA78L024AP

Three-Terminal Positive Regulators


5 V, 6 V, 7 V, 7.5 V, 8 V, 9 V, 10 V, 12 V, 13.2 V, 15 V, 18 V, 20 V, 24 V

Features
z Suitable for TTL, C2MOS power supply.
z Internal short-circuit current limiting.
z Internal thermal overload protection.
z Maximum output current of 150 mA (Tj = 25°C).
z Available in a plastic TO-92MOD package.

Pin Assignment

Marking side

2 3 1 Weight: 0.36 g (Typ.)


OUT GND IN

Marking

TA78L Part No. (or abbreviation code)


***AP Lot No.
(weekly code)
A line indicates
www.DataSheet4U.com lead (Pb)-free package or
lead (Pb)-free finish.

Equivalent Circuit

1 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Absolute Maximum Ratings (Ta = 25°C)

Characteristics Symbol Rating Unit

TA78L005AP
TA78L006AP
TA78L007AP
TA78L075AP
TA78L008AP
35
TA78L009AP
Input voltage TA78L010AP VIN V

TA78L012AP
TA78L132AP
TA78L015AP
TA78L018AP
TA78L020AP 40

TA78L024AP
Power dissipation (Ta = 25°C) PD 800 mW
Operating temperature Topr −30~85 °C
Storage temperature Tstg −55~150 °C
Junction temperature Tj 150 °C
Thermal resistance Rth (j-a) 156 °C/W

Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report
and estimated failure rate, etc).

www.DataSheet4U.com

2 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L005AP
Electrical Characteristics
(Unless otherwise specified, VIN = 10 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 4.8 5.0 5.2 V
7.0 V ≤ VIN ≤ 20 V ― 55 150
Line regulation Reg·line 1 Tj = 25°C mV
8.0 V ≤ VIN ≤ 20 V ― 45 100
1.0 mA ≤ IOUT ≤ 100 mA ― 11 60
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 5.0 30
7.0 V ≤ VIN ≤ 20 V,
4.75 ― 5.25
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 4.75 ― 5.25
Tj = 25°C ― 3.1 6.0
Quiescent current IB 1 mA
Tj = 125°C ― ― 5.5
8.0 V ≤ VIN ≤ 20 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 40 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 12 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 41 49 ― dB
8.0 V ≤ VIN ≤ 18 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.6 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

3 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L006AP
Electrical Characteristics
(Unless otherwise specified, VIN = 11 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 5.76 6.0 6.24 V
8.1 V ≤ VIN ≤ 21 V ― 50 150
Line regulation Reg·line 1 Tj = 25°C mV
9.0 V ≤ VIN ≤ 21 V ― 45 110
1.0 mA ≤ IOUT ≤ 100 mA ― 12 70
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 5.5 35
8.1 V ≤ VIN ≤ 21 V,
5.7 ― 6.3
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 5.7 ― 6.3
Tj = 25°C ― 3.1 6.0
Quiescent current IB 1 mA
Tj = 125°C ― ― 5.5
9.0 V ≤ VIN ≤ 20 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 40 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 14 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 39 47 ― dB
9.0 V ≤ VIN ≤ 19 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.7 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

4 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L007AP
Electrical Characteristics
(Unless otherwise specified, VIN = 12 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 6.72 7.0 7.28 V
9.2 V ≤ VIN ≤ 22 V ― 50 160
Line regulation Reg·line 1 Tj = 25°C mV
10 V ≤ VIN ≤ 22 V ― 45 115
1.0 mA ≤ IOUT ≤ 100 mA ― 13 75
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 6.0 40
9.2 V ≤ VIN ≤ 22 V,
6.65 ― 7.35
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 6.65 ― 7.35
Tj = 25°C ― 3.1 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
10 V ≤ VIN ≤ 22 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 50 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 17 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 37 46 ― dB
10 V ≤ VIN ≤ 20 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.75 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

5 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L075AP
Electrical Characteristics
(Unless otherwise specified, VIN = 13 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 7.21 7.5 7.79 V
9.8 V ≤ VIN ≤ 23 V ― 40 170
Line regulation Reg·line 1 Tj = 25°C mV
10.5 V ≤ VIN ≤ 23 V ― 40 120
1.0 mA ≤ IOUT ≤ 100 mA ― 14 80
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 6.5 40
9.8 V ≤ VIN ≤ 23 V,
7.125 ― 7.875
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 7.125 ― 7.875
Tj = 25°C ― 3.1 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
10.5 V ≤ VIN ≤ 23 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 60 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 19 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 37 45 ― dB
11 V ≤ VIN ≤ 21 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.75 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

6 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L008AP
Electrical Characteristics
(Unless otherwise specified, VIN = 14 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 7.7 8.0 8.3 V
10.5 V ≤ VIN ≤ 23 V ― 20 175
Line regulation Reg·line 1 Tj = 25°C mV
11 V ≤ VIN ≤ 23 V ― 12 125
1.0 mA ≤ IOUT ≤ 100 mA ― 15 80
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 7.0 40
10.5 V ≤ VIN ≤ 23 V,
7.6 ― 8.4
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 7.6 ― 8.4
Tj = 25°C ― 3.1 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
11 V ≤ VIN ≤ 23 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 60 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 20 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 37 45 ― dB
12 V ≤ VIN ≤ 23 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.8 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

7 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L009AP
Electrical Characteristics
(Unless otherwise specified, VIN = 15 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 8.64 9.0 9.36 V
11.4 V ≤ VIN ≤ 24 V ― 80 200
Line regulation Reg·line 1 Tj = 25°C mV
12 V ≤ VIN ≤ 24 V ― 20 160
1.0 mA ≤ IOUT ≤ 100 mA ― 17 90
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 8.0 45
11.4 V ≤ VIN ≤ 24 V,
8.55 ― 9.45
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 8.55 ― 9.45
Tj = 25°C ― 3.2 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
12 V ≤ VIN ≤ 24 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 65 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 21 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 36 44 ― dB
12 V ≤ VIN ≤ 24 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.85 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

8 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L010AP
Electrical Characteristics
(Unless otherwise specified, VIN = 16 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 9.6 10 10.4 V
12.5 V ≤ VIN ≤ 25 V ― 80 230
Line regulation Reg·line 1 Tj = 25°C mV
13 V ≤ VIN ≤ 25 V ― 30 170
1.0 mA ≤ IOUT ≤ 100 mA ― 18 90
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 8.5 45
12.5 V ≤ VIN ≤ 25 V,
9.5 ― 10.5
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 9.5 ― 10.5
Tj = 25°C ― 3.2 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
13 V ≤ VIN ≤ 25 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 70 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 22 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 36 43 ― dB
13 V ≤ VIN ≤ 24 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −0.9 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

9 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L012AP
Electrical Characteristics
(Unless otherwise specified, VIN = 19 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 11.5 12 12.5 V
14.5 V ≤ VIN ≤ 27 V ― 120 250
Line regulation Reg·line 1 Tj = 25°C mV
16 V ≤ VIN ≤ 27 V ― 100 200
1.0 mA ≤ IOUT ≤ 100 mA ― 20 100
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 10 50
14.5 V ≤ VIN ≤ 27 V,
11.4 ― 12.6
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 11.4 ― 12.6
Tj = 25°C ― 3.2 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
16 V ≤ VIN ≤ 27 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 80 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 24 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 36 41 ― dB
15 V ≤ VIN ≤ 25 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −1.0 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

10 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L132AP
Electrical Characteristics
(Unless otherwise specified, VIN = 21 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 12.67 13.2 13.73 V
16 V ≤ VIN ≤ 28 V ― 125 270
Line regulation Reg·line 1 Tj = 25°C mV
17 V ≤ VIN ≤ 28 V ― 105 225
1.0 mA ≤ IOUT ≤ 100 mA ― 22 120
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 11 60
16 V ≤ VIN ≤ 28 V,
12.54 ― 13.86
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 12.54 ― 13.86
Tj = 25°C ― 3.2 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
17 V ≤ VIN ≤ 28 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 90 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 28 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 34 41 ― dB
17 V ≤ VIN ≤ 27 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −1.2 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

11 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L015AP
Electrical Characteristics
(Unless otherwise specified, VIN = 23 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 14.4 15 15.6 V
17.5 V ≤ VIN ≤ 30 V ― 130 300
Line regulation Reg·line 1 Tj = 25°C mV
20 V ≤ VIN ≤ 30 V ― 110 250
1.0 mA ≤ IOUT ≤ 100 mA ― 25 150
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 12 75
17.5 V ≤ VIN ≤ 30 V,
14.25 ― 15.75
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 14.25 ― 15.75
Tj = 25°C ― 3.3 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
20 V ≤ VIN ≤ 30 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 90 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 30 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 34 40 ― dB
18.5 V ≤ VIN ≤ 28.5 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −1.3 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

12 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L018AP
Electrical Characteristics
(Unless otherwise specified, VIN = 27 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 17.3 18 18.7 V
21.4 V ≤ VIN ≤ 33 V ― 32 325
Line regulation Reg·line 1 Tj = 25°C mV
22 V ≤ VIN ≤ 33 V ― 27 275
1.0 mA ≤ IOUT ≤ 100 mA ― 30 170
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 15 75
21.4 V ≤ VIN ≤ 33 V,
17.1 ― 18.9
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 17.1 ― 18.9
Tj = 25°C ― 3.3 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
22 V ≤ VIN ≤ 33 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 150 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 45 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 32 38 ― dB
23 V ≤ VIN ≤ 33 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −1.5 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

13 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L020AP
Electrical Characteristics
(Unless otherwise specified, VIN = 29 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 19.2 20 20.8 V
23.5 V ≤ VIN ≤ 35 V ― 33 330
Line regulation Reg·line 1 Tj = 25°C mV
24 V ≤ VIN ≤ 35 V ― 28 285
1.0 mA ≤ IOUT ≤ 100 mA ― 33 180
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 17 90
23.5 V ≤ VIN ≤ 35 V,
19.0 ― 21.0
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 19.0 ― 21.0
Tj = 25°C ― 3.3 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
24 V ≤ VIN ≤ 35 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 170 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 49 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 31 37 ― dB
25 V ≤ VIN ≤ 35 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −1.7 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

14 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L024AP
Electrical Characteristics
(Unless otherwise specified, VIN = 33 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Output voltage VOUT 1 Tj = 25°C 23 24 25 V
27.5 V ≤ VIN ≤ 38 V ― 35 350
Line regulation Reg·line 1 Tj = 25°C mV
28 V ≤ VIN ≤ 38 V ― 30 300
1.0 mA ≤ IOUT ≤ 100 mA ― 40 200
Load regulation Reg·load 1 Tj = 25°C mV
1.0 mA ≤ IOUT ≤ 40 mA ― 20 100
27.5 V ≤ VIN ≤ 38 V,
22.8 ― 25.2
Output voltage VOUT 1 Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA V
1.0 mA ≤ IOUT ≤ 70 mA 22.8 ― 25.2
Tj = 25°C ― 3.5 6.5
Quiescent current IB 1 mA
Tj = 125°C ― ― 6.0
28 V ≤ VIN ≤ 38 V ― ― 1.5
Quiescent current change ΔIB 1 Tj = 25°C mA
1.0 mA ≤ IOUT ≤ 40 mA ― ― 0.1
Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz ― 200 ― μVrms
Long term stability ΔVOUT/Δt 1 ― ― 56 ― mV/kh
f = 120 Hz,
Ripple rejection R.R. 3 31 35 ― dB
29 V ≤ VIN ≤ 39 V, Tj = 25°C
Dropout voltage VD 1 Tj = 25°C, IOUT = 150 mA ― 1.7 ― V
Average temperature
TCVO 1 IOUT = 5 mA ― −2.0 ― mV/°C
coefficient of output voltage

www.DataSheet4U.com

15 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Test Circuit 1/Standard Application

Test Circuit 2
VNO

Test Circuit 3
R.R.

www.DataSheet4U.com

16 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP

www.DataSheet4U.com

17 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP

w w w . D a t a S h e e t 4 U . c o m

18 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Precautions for Use
Destruction of the IC may occur if high voltage in excess of the IC output voltage (typ. value) is applied to the IC
output terminal. In this case, connect a Zener diode between the output terminal and GND to prevent any
application of excessive voltage. In particular, in a current boosting circuit such as that shown in Application
Circuit Example (2), if the input voltage is suddenly applied by stages and furthermore, load is light, excessive
voltage may be applied transiently to the output terminal of the IC. In such a case, it may become necessary to
increase the capacity of the output capacitor as appropriate, use a smaller R1 (a resistor for bypassing IC bias
current) or gradually raise the input voltage in addition to using a Zener diode as mentioned above.

Application Circuits
(1) Standard Application

(2) A. Current Boost Voltage Regulator

B. Short-Circuit Protection

www.DataSheet4U.com

(3) Current Regulator

19 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
(4) Voltage Boost Regulator

(5) Negative Regulator

(6) Positive and Negative Regulator

www.DataSheet4U.com

20 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Package Dimensions

www.DataSheet4U.com

21 2006-11-02
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP

RESTRICTIONS ON PRODUCT USE 20070701-EN

• The information contained herein is subject to change without notice.

• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
www.DataSheet4U.com
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.

• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.

• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.

• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.

22 2006-11-02

You might also like