HT-SB300

SERVICE MANUAL
No. S2907HTSB300U

SOUND BAR SYSTEM

MODEL HT-SB300
• In the interests of user-safety the set should be restored
to its original condition and only parts identical to those
specified be used.

is a trademark of SRS Labs, Inc.

WOW HD technology is incorporated under license

from SRS Labs, Inc.

CONTENTS

PRECAUTIONS FOR USING LEAD-FREE SOLDER CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS
CHAPTER 1. GENERAL DESCRIPTION LAYOUT
[1] Important Service Safety Precaution ............... 1-1 [1] Notes On Schematic Diagram........................ 6-1
[2] Important Service Notes (for U.S.A only)......... 1-1 [2] Types Of Transistor And LED........................ 6-1
[3] Specifications................................................ 1-2 [3] Schematic Diagram........................................ 6-2
[4] Name Of Parts ...............................................1-3 [4] Chart Of Connecting Wires .......................... 6-16
[5] Wiring Side Of PWB..................................... 6-18
CHAPTER 2. ADJUSTMENTS
[1] Test Mode ......................................................2-1 CHAPTER 7. OTHERS
[1] Function Table Of IC ...................................... 7-1
CHAPTER 3. MECHANISM BLOCKS
[1] Disassembly ..................................................3-1 PARTS GUIDE

CHAPTER 4. DIAGRAMS
[1] Block Diagram ...............................................4-1

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Voltage...........................................................5-1

Parts marked with " ! " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION for after sales service only.
The contents are subject to change without notice.
HT-SB300
PRECAUTIONS FOR USING LEAD-FREE SOLDER

1. Employing lead-free solder

"MAIN, POWER, AMPLIFIER PWB" of this model employs lead-free solder. The LF symbol indicates lead-free
solder, and is attached on the PWB and service manuals. The alphabetical character following LF shows the type
of lead-free solder.

Example:

Indicates lead-free solder of tin, silver and copper.

2. Using lead-free wire solder

When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend
you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering
bit, contact our service station or service branch in your area.

3. Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead
solder by 40°C,and as it has poor solder wet ability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, since the land may be peeled of for the maximum heat-resistance
temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady
soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn
on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is
alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sand paper.
Be careful when replacing parts with polarity indication on the PWB silk.

Lead-free wire solder for servicing

Ref No. Parts No. Description
PWB-A 92LPWB7412MANS MAIN (A1) / POWER (A2) / AMPLIFIER (A3)

–i–
 HT-SB300
CHAPTER 1: GENERAL DESCRIPTION
[1] Important Service Safety Precaution

CAUTION : “These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so”.

WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
3. CAUTION: “Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type”.

[2] Important Service Notes (for U.S.A only)

BEFORE RETURNING THE AUDIO PRODUCT

(Fire & Shock Hazard)
Before returning the audio product to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the audio product.
VTVM
2. Inspect all protective devices such as insulating AC SCALE
materials, cabinet, terminal board, adjustment and
compartment covers or shields, mechanical insulators
etc. 1.5k ohms
10W
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
0.15 µ F
* Using two clip leads, connect a 1.5k ohm, 10 watt TEST PROBE
resistor paralleled by a 0.15µF capacitor in series CONNECT TO
TO EXPOSED
with all exposed metal cabinet parts and a known KNOWN EARTH
METAL PARTS
earth ground, such as conduit or electrical ground GROUND
connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or
higher, sensitivity to measure the AC voltage drop All check must be repeated with the AC line cord plug
across the resistor (See diagram). connection reversed.
* Connect the resistor connection to all exposed metal Any reading of 0.3 volt RMS (this corresponds to 0.2
parts having a return path to the chassis (antenna, milliamp. AC.) Or more is excessive and indicates a
metal cabinet, screw heads, knobs and control shafts, potential shock hazard which must be corrected before
escutcheon, etc.) and measure the AC voltage drop returning the audio product to the owner.
across the resistor.

1 ––2
1
HT-SB300
[3] Specifications

General
Power source DC IN 12V 4A: AC/DC adaptor
(AC 100 - 240 V ~ 50/60 Hz)
Power 11 W
consumption
Maximum output 32 W
power
Speaker 2.1-way Speaker System
Front Speakers: 1-1/2” (38mm) Full Range
Impedance: 12 ohms/channel
Subwoofer: 2-1/4" (57 mm) Woofer x 4
Impedance: 3 ohms
(12 ohms x 4 parallel connection)
Input terminals Analog input (LINE 1):
RCA type x 1pair (L/R)
500 mV / 47 kohms
Analog input (LINE 2):
Stereo mini jack Ø 3.5 mm
100 mV / 47 kohms
Coaxial digital input (DIGITAL 1):
RCA type x 1
Optical digital input (DIGITAL 2):
Square type x 1
Audio output Subwoofer Pre Out: 10 kohms
terminals
Dimensions Width: 31-1/2" (800 mm)
Height: 3-3/4" (96 mm)
Depth: 2-3/4" (70 mm)
Weight 4.10 lbs. (1.85 kg)

1–3
2
 HT-SB300
[4] Names Of Parts

Front panel
1. Sport Indicator
2. Standard Indicator
12 3 45 3. Information Display
4. Cinema/Game Indicator
5. News Indicator
6. DTS Indicator
7. Dolby Indicator
8. On/Stand-by Button
9. Volume Down Button
6 7 8 9 10 11 12 13 14 15 10. Volume Up Button
11. Surround Button
16 17 18 18 17 19 12. Function Button
13. Remote Sensor
14. Dolby Virtual Speaker Indicator
15. Dolby Prologic II Indicator
16. Left Front Speaker
17. Bass Reflex Duct
18. Subwoofers
19. Right Front Speaker

1 2 3 4 5 6
Rear Panel
1. Audio Line In 2 Jack
LINE IN 2
RIGHT LEFT
LINE IN 1
2. Line In 1 Jacks
3. DC IN Jack
4. Coaxial Digital Audio Input Jack
5. Optical Digital Audio Input Jack
6. Subwoofer Pre Output Jack

1 Remote Control
1. Remote Control Transmitter
2 10 2. Dolby Virtual Speaker Button
3 11 3. Cinema/Game Button
4. Standard Button
4 12 5. Volume Up Button
6. Subwoofer Level Down Button
5 7. Volume Down Button
13 8. Bass/Treble Button
6 14 9. TV Operation Buttons
7 15 10. On/Stand-by Button
8 16 11. Sport Button
12. News Button
13. Subwoofer Level Up Button
9 17 14. Dimmer Button
15. Mute Button
18 16. Line Button
17. Digital 1 Button
18. Digital 2 Button

TV Operation Buttons (Only SHARP TV):

On/Stand-by Sets the TV Input Select Press the
Button power to “ON” Button (TV) button to
or “STAND- switch the
BY”. input source.

Volume Up Turn up/down Channel Up Switch up/

and Down the TV and Down down the TV
Buttons volume. Buttons channels.

Notes:
Some models of SHARP TV may not be operable.
SHARP TV remote will not work with HT-SB300 system.

1 ––23
HT-SB300
CHAPTER 2. ADJUSTMENTS
[1] Test Mode

1. Enter the Test Mode version display

While pressing down ON/STANDBY and VOL UP button, ON AC supply.
Version will be display on 7 segment as below:-
b3 --> XX --> D

b3 = Model name, SB300

XX= version no.
D = Destination

2. Enter Key and Display Test Mode

After enter Test Mode version display, Press VOL UP button.
1. All SOUND MODE LED will light ON
2. 7 segment display will light on if press button as below

Key 7 segment
VOL DOWN 01
VOL UP 02
SURROUND 03
FUNCTION 04

3. Exit the Test Mode

While in Test Mode function, Press ON/STANDBY button to exit.

4. Error Code Description.

Display Explanation Solution
E1 Communication error between Micom and AK4683 > Unplug AC cord and turn power ON again
E2 Communication error between Micom and CS4953xx > Check line connected between Micom and corresponding IC
E3 Communication error between Micom and STA333

5. System Protection indicator

In case abnormal power detection has occurred, the unit will automatically enter to stand-by mode
ON/Standby LED willl be flashing as below:-

ON Flashing ON Flashing
OFF OFF OFF OFF
(3 Sec) (3 Sec) (3 Sec) (3 Sec) (3 Sec)
No.1 No.2 No.1 No.2
1 Frame (Repeat)

Fig. Example for No. 2 AVCK Protect

Unit enter Protect mode when irregular process occur on power supply line.

1. System Protect
2. AVCK Protect

2–1
 HT-SB300
CHAPTER 3. MECHANISM BLOCKS
Service Manual
E
Market
CD-ES700/CD-ES77

[1] Disassembly
Caution On Disassembly

Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit.
2. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were before disassembling.
3. Check that all speaker cushions (refer items 214, 216, 217 and 218 on pages 6 and 7 of Parts Guide) are properly
sealed otherwise vibration noise will be very distinct at low frequency sound.
Replace the cushions if they are found damaged during servicing.

STEP REMOVAL PROCEDURE FIGURE

1 Back Cabinet Assy 1. Wall Mount Bracket…… (A1)x2 1
2. Screw…………..………. (A2)x10
3. Screw…………..………. (A3)x13
2 Amp PWB 1. Screw……….………….. (B1)x2 2
2. Connector…….……….. (B2)x1
3. Socket………………..… (B3)x2
3 Power PWB 1. Main Chassis……….…. (C1)x1 2
2. Screw………….…….…. (C2)x4
3. Screw………….…….…. (C3)x2
4. Screw………….………. (C4)x2
5. Socket………………..… (C5)x1
6. Flat Cable………….…… (C6)x1
4 Woofer 1. Duct Port Holder…….… (D1)x2 3
2. Duct Port Assy………… (D2)x2 3
3. Screw………….…….…. (D3)x12 3
2. Screw………….………. (D4)x8 4
5 Speaker 1. Screw………….………. (E1)x8 4

Back Cabinet Ass’y

(A3)x4
M3x10mm Front Cabinet Ass’y

(A2)x5
M3.5x10mm

(A1)x1
(A3)x2
Wall Mount Bracket
M3x10mm

(A1)x1
Wall Mount Bracket

(A2)x5
M3.5x10mm (A3)x7
M3x10mm

Figure 1

3–1
HT-SB300

Front Cabinet Ass’y

Main PWB

(C1)x1
Main Chassis

(C2)x4
M3x10mm
(B3)x1

Amplifier PWB (C6)x1

(C3)x1
Special Screw (C5)x1
(B3)x1
(B2)x1
(B1)x2 Power PWB
(C4)x2
Special Screw M3x8mm (C3)x1
Special
Screw
Figure 2

Front Cabinet Ass’y

(D3)x6 (D1)x1
M3x10mm Duct Port Holder

(D2)x1
Duct Port Ass’y (D1)x1
Duct Port Holder

(D2)x1
Duct Port Ass’y
Figure 3

(D3)x6
M3x10mm

(E1)x4
M2.6x8mm
(D4)x2
M3x10mm
Speaker
(D4)x2
Woofer M3x10mm

Woofer
(D4)x2
SPEAKER UNIT
M3x10mm LOCKING TAB
(D4)x2
M3x10mm SPEAKER
WIRE
(E1)x4 LOCKING TAB

Woofer M2.6x8mm
Woofer
CAUTION:
Speaker TO REMOVE SPEAKER UNIT, PRESS THESE LOCKING TABS
TO RELEASE SPEAKER WIRES.
Figure 4

Front Cabinet Ass’y

3–2
 HT-SB300
-MEMO-

3–3
HT-SB300
CHAPTER 4. DIAGRAM
[1] Block Diagram

BI303 BI304 CNP80 CNP90

CNW303 8 +B5
2 2 4 V 2
V- SWF PRE-OUT 2
-VE CNW905 -VE
NB154AWPZ
1 1 7 6 +VE NB230AWPZ 1 +VE
IC603 1
SWF PRE-OUT
3
TJM4558CD 5

Q300 LVL_DETECT CA145WJ

JK304 2 1
2SD601A 12.2880MHz
SUBWOOFER PRE-OUT
D805 +B4 XM101
MA111G DZ803
CNP301 CNP101
EXA507WJ
MUTE 15 15
10 24 54 66 83 98 119 130 124 125

LVL_DETECT

VDD5
14

VDD4

VDD6

VDD7

VDD8
VDD1

VDD2

VDD3
LVL_DETECT

12
1 IC301 8 +B3 PROTECT
13
TC7WU04U

NB196AWPZ
9

CNW301
4 2
DC_RELAY
JK303 12 8
13 17 21 24 27 29
CO-AXIAL ( DIGITAL IN ) ~ ~ 8

11 11
123

DVDD 10
+B3 20 +B2 140
40

~
LOUT
7
141
41 ROUT1 5

~
2 2
142 IC602
6
RXM301 NJU260409
OPTICAL ( DIGITAL IN ) IC300 1 1
10
13
SRS WOW
AK4683EQ GND1
11 27
2 RX0 GND2
14
4 RX1 57 GND3
19 69
51 GND4
Lch LIN1
28 86
52 RIN1 GND5
L
30 101
GND6
53 LIN2
AVDD

AVDD

VDDIO3

VDDIO4
HVD

VDDIO1

VDDIO2

VDDIO5

VDDIO6
PVDD

119
Rch 54 RIN2 GND7
32
133
GND8
34 44 49 63 50 43 33 1
JK802 (LINE IN) 93 97 99 100 102 18 33 44 60 73

+B1

DZ802 +B3
L 1 5.6B
+B4 +B2 Q802
IC804
R 3 2
KIA1117F18L
D1.8V LED701
JK801 (AUDIO IN) +B4 SEVEN SEGME
Q805 Q806
KW2402CB
1 1
~
+B3
IC803
3 2
KIA1117S33L
D3.3V
+B1 Q800 29

28
DC_12V A_5.0V
15 I
+B1
FROM AC P

~
DZ801 1 3
6 2
ADAPTOR IC801 9
SK52B 5A/20V Q801 LV5805M 1
4
35 ~ 38 40 51 52 47 50 5
3
KMS6D0P20X 5
+B2 ~
80
D_5.0V 56

~
DIR_INT
2
JK803 DZ801
~

4 57 DIR_PDN 77
DC IN SMAB33L
81 LVL DETECT
12V 4A 76 Q701
85 MUT 2
DC_12V +B5 +B8 +B8 Q501
90 4
POWER 75 Q702
IC501
91
2 SYS IXA230AW LED702
+B6 IC605 SYSTEM CL165SRD
AMP_12V 1 12
KEY 92
3 Q500 RESE
PST8227N MICROCOMPUTER POWER
10
XCIN KEY KE
XM501 KEY1 93
SW702-SW705 SW7
32.768KHz 11
XCOU
34
MICOM_UNSW
3 13 XOU
XM502
~

UNSW_12V
2 3
+B7 12MHz ~ 31
IC803
AP2213 UNSW 3.3 2
12
D503
10
5 ~ 8 1 15
XI GN VCC AVCC
+B9
VREF RX_IN
+B8 14 64 96 16 62 99 98 20
3.3V REMOTE 3
1 +B7
D502 SENSOR
+B9 +B7 +B8 2

3.3V

CNP302 CNP102 CNP803 CNP902

+B1 1 1 D_1.8V +B3 1 1 D_3.3V

2 2 D_1.8V 2 2 DGND
3 3 DGND 3 3 DGND
NB154AWPZ

4 4 DGND
CNW302

4 4 AMP_12V
+B6
+B3 5 5 D_3.3V 5 5 AMP_12V
6 6 MICOM GND 6 6 AMP_12V

7 7 UNSW_3.3V
+B9 7 7
AMP_GND
8 8 DGND 8 8 AMP_GND

+B2 9 9 D_5V 9 9 AMP_GND

Figure 4-1: BLOCK DIAGRAM (1/2)

4–1
 HT-SB300

CA145WJ
12.2880MHz
XM101

119 130 124 125

VDD7

VDD8

19

20 CNP10 CNP90
22
10 10

5 5
~

~
NB197AWPZ

GNDIO1 21 2 2
CNW103

GNDIO2 36 9 9

IC602 GNDIO3 47 8 8
JU260409
63
RS WOW GNDIO4 11 11 Q802 Q802
GNDIO5 76
7 7
GNDIO6 94
6 6
116
GNDIO7 1 1
GND 126

GNDIO8 139
VDDIO3

VDDIO4

VDDIO8
VDDIO1

VDDIO2

VDDIO5

VDDIO6

VDDIO7

VDDA

18 33 44 60 73 91 113 129 129

23 9

IC901 6
27
STA333BW
+B3 POWER IC 13
~

34
10

17
11
~

CL191HB VCC +B6

19 8
LED701 LED703 ~ LED710
SEVEN SEGMENT 16
21 VDD_DI CONFIG
KW2402CB R
1 1
+B3 24 PLL_VD GND1 12
1 16 2 2
~ FRONT = 12Ω
36 VDD_DI GND2 7
L 3 3
22 TEST 3
VSS_DIG
MODE 4 4
26 PLL_GND S 2
29 22 5 5
35 VDD_GND GND SUB 1 SWF
~

28
~

16 8 8
15 IC701
15
PT6965
~

9 23
VDD +B2
8
5
SUBWOOFER TOTAL 3Ω
24
(12Ω / speaker unit &
~

GND
2 30 connected in parallel)

25 2
2 IC902 3
29
4 1 STA533BW
+B7 POWER IC 8
3 32
LED702
~

CL165SRD 11

4 16

KEY KEY 7 17
702-SW705 SW701 VCC
+B6 12

15 14
8

13
~

3 GND
6
+B3 23 VL
2 5
+B9
1 19 GND_CLEAN GND SUB 1

MOTE 3 +B7
NSOR
2

Figure 4-2: BLOCK DIAGRAM (2/2)

4–2
HT-SB300
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Voltage
IC101
PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE
NO (V) NO (V) NO (V) NO (V)
1 3.307 37 2.967 73 3.314 109 3.310
2 3.000 38 3.314 74 0.000 110 3.310
3 3.305 39 3.306 75 0.000 111 3.310
4 0.000 40 3.306 76 0.000 112 3.310
5 0.000 41 3.306 77 0.000 113 3.310
6 0.000 42 3.306 78 3.311 114 3.310
7 0.000 43 3.306 79 3.306 115 3.310
8 1.016 44 3.314 80 3.310 116 1.760
9 0.000 45 3.319 81 3.310 117 3.310
10 1.765 46 3.207 82 0.000 118 3.310
11 0.000 47 0.000 83 1.760 119 1.760
12 1.647 48 3.284 84 0.000 120 0.782
13 0.000 49 3.284 85 0.000 121 3.310
14 1.645 50 3.312 86 0.000 122 0.000
15 1.640 51 1.750 87 0.000 123 0.830
16 0.000 52 0.000 88 3.310 124 0.730
17 0.000 53 3.312 89 3.310 125 1.340
18 3.314 54 1.760 90 3.310 126 0.004
19 2.241 55 0.000 91 3.310 127 0.062
20 1.643 56 0.000 92 0.000 128 1.610
21 1.637 57 0.000 93 3.310 129 3.310
22 0.417 58 0.000 94 3.310 130 1.760
23 0.000 59 0.000 95 3.310 131 0.000
24 1.760 60 3.316 96 1.760 132 0.000
25 3.314 61 0.000 97 3.310 133 0.000
26 3.306 62 0.000 98 1.770 134 0.000
27 0.000 63 3.314 99 0.000 135 3.310
28 3.314 64 0.000 100 3.310 136 3.310
29 3.304 65 0.000 101 3.310 137 3.310
30 3.306 66 1.765 102 3.310 138 3.310
31 3.306 67 0.000 103 3.310 139 0.000
32 3.306 68 0.000 104 3.310 140 1.620
33 3.314 69 0.000 105 3.310 141 1.610
34 3.306 70 0.000 106 3.310 142 1.700
35 3.306 71 0.000 107 3.310 143 3.306
36 0.000 72 0.000 108 3.310 144 3.306

IC300
PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE
NO (V) NO (V) NO (V) NO (V)
1 4.970 17 3.360 33 4.970 49 0.000
2 2.450 18 3.360 34 0.000 50 4.970
3 4.970 19 0.000 35 0.000 51 2.470
4 0.283 20 4.970 36 0.000 52 2.470
5 0.110 21 2.900 37 0.043 53 2.470
6 0.000 22 2.480 38 2.470 54 2.490
7 3.340 23 2.480 39 2.470 55 2.480
8 0.110 24 0.830 40 2.470 56 2.480
9 0.110 25 3.113 41 2.470 57 2.470
10 0.000 26 3.360 42 2.470 58 2.470
11 0.000 27 3.120 43 0.497 59 2.470
12 0.110 28 0.000 44 0.000 60 2.480
13 1.670 29 2.230 45 2.470 61 2.470
14 0.000 30 0.000 46 2.470 62 2.480
15 1.650 31 0.000 47 2.470 63 0.000
16 1.520 32 0.000 48 2.470 64 1.201

5–1
 HT-SB300
IC501
PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE
NO (V) NO (V) NO (V) NO (V)
1 0.000 26 0.000 51 3.360 76 1.390
2 0.000 27 0.000 52 3.180 77 3.170
3 0.000 28 0.000 53 0.000 78 3.360
4 0.000 29 0.000 54 0.000 79 3.170
5 0.000 30 0.000 55 1.064 80 0.000
6 0.000 31 0.000 56 3.340 81 1.160
7 0.000 32 0.000 57 3.170 82 2.140
8 0.000 33 0.000 58 0.000 83 0.000
9 0.000 34 0.000 59 0.000 84 0.000
10 0.560 35 3.360 60 0.000 85 0.000
11 1.090 36 3.360 61 1.100 86 0.000
12 3.150 37 3.160 62 3.170 87 0.000
13 1.550 38 3.360 63 0.000 88 3.110
14 0.000 39 1.580 64 0.000 89 1.620
15 1.390 40 3.360 65 0.000 90 3.070
16 3.170 41 0.000 66 0.000 91 3.080
17 3.160 42 0.000 67 0.000 92 0.000
18 0.000 43 0.000 68 0.000 93 3.070
19 3.080 44 0.000 69 0.000 94 0.000
20 3.080 45 0.000 70 0.000 95 0.000
21 0.000 46 3.170 71 0.000 96 0.000
22 0.000 47 0.000 72 0.000 97 0.000
23 0.000 48 3.240 73 0.000 98 3.080
24 0.000 49 3.170 74 0.000 99 3.125
25 0.000 50 3.170 75 3.140 100 0.000

IC502 IC701
PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE
NO (V) NO (V) NO (V) NO (V)
1 3.100 1 2.250 11 3.390 21 0.560
2 3.100 2 3.360 12 3.390 22 0.810
3 0.000 3 2.230 13 2.250 23 1.460
4 0.000 4 2.470 14 1.970 24 0.497
5 0.000 5 1.900 15 3.290 25 0.497
6 0.000 16 3.530 26 2.480
7 0.000 17 1.460 27 0.000
IC801 8 3.700 18 2.090 28 2.370
PIN VOLTAGE 9 4.970 19 3.410 29 2.740
NO (V) 10 3.640 20 0.560 30 0.000
1 9.300
2 11.830
3 5.240 IC804 IC805 IC806
4 0.000 PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE
5 0.794 NO (V) NO (V) NO (V)
6 1.371 1 -0.525 1 11.580 1 6.110
7 11.510 2 1.300 2 11.780 2 5.890
8 1.984 3 4.430 3 3.837 3 5.700
4 1.942 4 0.000
Q801 5 0.000 5 1.117
IC803 PIN VOLTAGE 6 0.000 6 0.996
PIN VOLTAGE NO (V) 7 0.000 7 11.420
NO (V) 1 11.830 8 0.000 8 11.830
1 -0.525 2 11.840
2 2.837 3 7.050
3 4.430 4 11.860
5 11.840
6 11.850

5–2
HT-SB300

IC901 IC902
PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE
NO (V) NO (V) NO (V) NO (V)
1 0.000 19 3.250 1 0.000 19 0.000
2 0.000 20 3.230 2 0.612 20 0.000
3 0.000 21 3.240 3 0.612 21 3.370
4 0.862 22 0.000 4 11.850 22 3.370
5 11.830 23 3.120 5 0.000 23 3.360
6 0.501 24 3.360 6 0.000 24 3.370
7 0.000 25 0.562 7 11.850 25 3.240
8 11.840 26 0.000 8 0.612 26 3.200
9 0.362 27 1.060 9 0.612 27 3.080
10 0.000 28 1.682 10 0.000 28 0.000
11 11.850 29 1.680 11 0.000 29 1.625
12 0.000 30 2.190 12 11.850 30 1.625
13 0.000 31 3.150 13 0.000 31 1.625
14 0.000 32 3.240 14 0.000 32 1.625
15 3.370 33 3.360 15 11.850 33 0.000
16 0.000 34 3.130 16 0.000 34 0.000
17 1.620 35 0.000 17 0.000 35 11.800
18 0.000 36 3.240 18 0.000 36 11.800

5–3
 HT-SB300
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
[1] Notes On Schematic Diagram
• Resistor: • Schematic diagram and Wiring Side of P.W.Board
To differentiate the units of resistors, such symbol as for this model are subject to change for
K and M are used: the symbol K means 1000 ohm improvement without prior notice.
and the symbol M means 1000 kohm and the • The indicated voltage in each section is the one
resistor without any symbol is ohm-type resistor. measured by Digital Multimeter between such a
Besides, the one with “Fusible” is a fuse type
section and the chassis with no signal given.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: • Parts marked with “ ” are important for
this symbol P means pico-farad and the unit of the maintaining the safety of the set. Be sure to replace
capacitor without such a symbol is microfarad. As to these parts with specified ones for maintaining the
electrolytic capacitor, the expression “capacitance/ safety and performance of the set.
withstand voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type

REF. NO DESCRIPTION POSITION

SW701 POWER ON/STAND-BY ON—OFF
SW702 VOLUME DOWN ON—OFF
SW703 VOLUME UP ON—OFF
SW704 SURROUND ON—OFF
SW705 FUNCTION ON—OFF

[2] Types Of Transistor And LED

TOP VIEW
B
(3)
TOP C
TOP VIEW
VIEW (2)
E
(1)
B(1) C(2) E(3)
KiA1117F KRC101S MA111G
KRC107S
KRA107S
KRC104S
DIG 1 DIG 2 DIG 2

F G B

E C

4 5
COM COM

DIG 1 DIG 2

PCL191 A B C D E F G A B C D E F G
CL165SRD 15 13 1 3 2 14 16 10 12 8 6 7 11 9

PCL165S
TOP VIEW

KDS226

6–1
HT-SB300
[3] Schematic Diagram

MAIN PWB-A1

1 2 3 4 5 6
Figure 6-1: MAIN SCHEMATIC DIAGRAM (1/6)
6–2
 7
8
144
143
142
141
140
139
138
137
136
135
134
133

9
132
131
130
129
128

6–3
127
126
125
124
123
122

10
121
120
119
118
117
116

Figure 6-2: MAIN SCHEMATIC DIAGRAM (2/6)

115
114
113
112
111

11
110
109
100
101
102
103
104
105
106
107
108

12
HT-SB300
HT-SB300

2 13 14 15 16 17 18
Figure 6-3: MAIN SCHEMATIC DIAGRAM (3/6)
6–4
 HT-SB300

1 2 3 4 5 6
Figure 6-4: MAIN SCHEMATIC DIAGRAM (4/6)
6–5
HT-SB300

7 8 9 10 11 12
Figure 6-5: MAIN SCHEMATIC DIAGRAM (5/6)
6–6
 HT-SB300

13 14 15 16 17 18
Figure 6-6: MAIN SCHEMATIC DIAGRAM (6/6)
6–7
HT-SB300

POWER PWB-A2

D
1(COAXIAL)

E
DIGITAL IN

DIN1
2(COAXIAL)

1 2 3 4 5 6
Figure 6-7: POWER SCHEMATIC DIAGRAM (1/6)

6–8
 HT-SB300

TO MAIN SECTION TO MAIN SECTION

(CNP101) (CNP102)

7 8 9 10 11 12
Figure 6-8: POWER SCHEMATIC DIAGRAM (2/6)
6–9
HT-SB300

SUBWOOFER
PRE-OUT

13 14 15 16 17 18
Figure 6-9: POWER SCHEMATIC DIAGRAM (3/6)

6 – 10
 HT-SB300

DIGITA DIN1

2(COAXIAL)

B
LINE IN 1

E
LINE IN 2

1 2 3 4 5 6
Figure 6-10: POWER SCHEMATIC DIAGRAM (4/6)
6 – 11
HT-SB300

7 8 9 10 11 12
Figure 6-11: POWER SCHEMATIC DIAGRAM (5/6)

6 – 12
 HT-SB300

AC POWER
SUPPLY CORD
100 - 240V ~ 50/60Hz

13 14 15 16 17 18
Figure 6-12: POWER SCHEMATIC DIAGRAM (6/6)
6 – 13
HT-SB300

AMP PWB-A3

D
TO POWER SECTION

1 2 3 4 5 6
Figure 6-13: AMPLIFIER SCHEMATIC DIAGRAM (1/2)

6 – 14
 HT-SB300

SPEAKER SYSTEM (R-CH)

SPEAKER
SP2

WOOFER
SP6

WOOFER
SP5

WOOFER
SP4

SUBWOOFER PRE-OUT

WOOFER
SP3

SPEAKER
SP1

SPEAKER SYSTEM (L-CH)

7 8 9 10 11 12
Figure 6-14: AMPLIFIER SCHEMATIC DIAGRAM (2/2)
6 – 15
 F
C
B

E
D

H
G
A

1
HT-SB300

2
(Top Side)
MAIN PWB-A1
[4] Charts Of Connecting Wires

CNP101 CNP10 3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 CNP10 2
1 2 3 4 5 6 7 8 9

1 2 3 4 5 678
CNP501
FOR
EXTERNAL MICOM
CNS101-A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 CNS103-A DEVICE ONLY

YL
BL

BK
BK
BK
PK
BK
BK
BK
BK
BK
BK
BK
BK
BK
PK
BK
BK
BK
BK
BK
BK
BK

3
WH
WH
WH
FFC102
CNS101-B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

TO
AMP PWB-A3
TO TO
POWER PWB-A2 CNP901 POWER PWB-A2
CNP301

6 – 16
CNP302

4
RD

WH
12 21

21

12
JK303 JK304

Bi304
JK801 Bi303

Figure 6-15: WIRING CONNECTION (1/2)

CNP302 RXM301
JK802 JK803

(Bottom Side)
987654321

POWER PWB-A2
CNP301
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

5
AC 100 - 240V ~ 50/60Hz
21
CNP804

AUDIO IN

AC POWER SUPPLY CORD

R-CH L-CH

2
1
CNP803

DC INPUT
1 2 3 4 5 6 7 8 9

AC / DC ADAPTOR
2 (OPTICAL)

1 (COAXIAL)

LINE IN 2
LINE IN 1
1 2 CNS302

CORE
DIGITAL IN
SUBWOOFER PRE-OUT

RD
WH

6
(2 x TURN)
CYLINDER CORE
DC IN 12V , 4A
RD
WH
 HT-SB300

RD SPEAKER
SP2
WH

RD
87654321 WOOFER
SP6
CNP905 CNP903 WH
21
CORE (CYLINDER)
RF
1 2 CNS

8 7 6 5 4 3 2 1 CNS903

WH
RD

WH
1 2 3 4 5 6 7 8 9

RD
RD
BK
GY WOOFER
WH SP5
RD CORE
CNP902

GY RING WH
BK (2 TURNS)
AMP PWB-A3
(Bottom Side)

SPEAKER SYSTEM (R-CH)

CNP901
1 2 3 4 5 6 7 8 9 10 11
CORE (CYLINDER)
RF

1 2 3 4 5 6 7 8 9 10 11 CNS103-B
GY

WOOFER
WH
BK

BK
BK
BK
BK
BK
BK
BK
PK
BL

SP4

BK

FROM
MAIN PWB-A1
CNP103
GY

WOOFER
SP3
BK

GY
SPEAKER
SP1
BK

SPEAKER SYSTEM (L-CH)

COLOR TABLE
RD RED
BK BLACK
WH WHITE
GY GREY
YL YELLOW
BL BLUE
PK PINK

7 8 9 10 11 12
Figure 6-16: WIRING CONNECTION (2/2)

6 – 17
HT-SB300
[5] Wiring Side Of PWB

A MAIN PWB-A1

FOR EXTERNAL
MICOM REFLASH
ONLY
C
1 23 4 5 6 7 8

Lead-free solder indication

Lead-free solder is used in the MAIN PWB.

H Refer to "Precautions for handling lead-free solder" for instructions
and precautions.

1 2 3 4 5 6
Figure 6-17: WIRING SIDE OF MAIN PWB (TOP VIEW) (1/2)
6 – 18
 HT-SB300

9 8 7 6 54 3 2 1

11 10 9 8 7 6 5 4 3 2 1 15 14 13 12 11 10 9 8 7 6 54 3 2 1

7 8 9 10 11 12
Figure 6-18: WIRING SIDE OF MAIN PWB (TOP VIEW) (2/2)
6 – 19
HT-SB300

A MAIN PWB-A1

Lead-free solder indication

Lead-free solder is used in the MAIN PWB.

H Refer to "Precautions for handling lead-free solder" for instructions
and precautions.

1 2 3 4 5 6
Figure 6-19: WIRING SIDE OF MAIN PWB (BOTTOM VIEW) (1/2)
6 – 20
 HT-SB300

1
2
3

7 8 9 10 11 12
Figure 6-20: WIRING SIDE OF MAIN PWB (BOTTOM VIEW) (2/2)
6 – 21
HT-SB300

A POWER PWB-A2

F
1 2

Lead-free solder indication

Lead-free solder is used in the POWER PWB.

H Refer to "Precautions for handling lead-free solder" for instructions
and precautions.

1 2 3 4 5 6
Figure 6-21: WIRING SIDE OF POWER PWB (TOP VIEW) (1/2)

6 – 22
 HT-SB300

1 2 3

2 1

7 8 9 10 11 12
Figure 6-22: WIRING SIDE OF POWER PWB (TOP VIEW) (2/2)
6 – 23
HT-SB300

A POWER PWB-A2

C
DIGITAL IN
SUBWOOFER PRE-OUT

1 (COAXIAL)

9 8
2 (OPTICAL)

1 2 3 4 5 6 7 8 9101112131415

9 8 7 6 543 2 1
RXM301
JK304
WH
RD

1 2
E

Lead-free solder indication

Lead-free solder is used in the POWER PWB.

H Refer to "Precautions for handling lead-free solder" for instructions
and precautions.

1 2 3 4 5 6
Figure 6-23: WIRING SIDE OF POWER PWB (BOTTOM VIEW) (1/2)

6 – 24
 HT-SB300

LINE 1

LINE 2
9 8 7 6 5 4 3 2 1

AUDIO IN
R-CH
DC INPUT

L-CH
12

12

COLOR TABLE
RD RED
WH WHITE

7 8 9 10 11 12
Figure 6-24: WIRING SIDE OF POWER PWB (BOTTOM VIEW) (2/2)
6 – 25
HT-SB300

A AMPLIFIER PWB-A3

Lead-free solder indication

Lead-free solder is used in the AMPLIFIER PWB.

H Refer to "Precautions for handling lead-free solder" for instructions
and precautions.

1 2 3 4 5 6
Figure 6-25: WIRING SIDE OF AMPLIFIER PWB (TOP VIEW)

6 – 26
 HT-SB300

A AMPLIFIER PWB-A3

2 1
8 7 6 5 4 3 2 1

C
1 2 3 4 5 6 7 8 9

G
1 2 3 4 5 6 7 8 9 10 11

Lead-free solder indication

Lead-free solder is used in the AMPLIFIER PWB.

H Refer to "Precautions for handling lead-free solder" for instructions
and precautions.

1 2 3 4 5 6
Figure 6-26: WIRING SIDE OF AMPLIFIER PWB (BOTTOM VIEW)
6 – 27
HT-SB300
CHAPTER 7. OTHERS
[1] Function Table Of IC
IC300 VHiAK4683EQ-1 : Multi-Channel Audio Codec ( AK4683EQ ) ( 1/3 )

RMCLK
RX0 4:2 Clock
RX1 Input Recovery DAIF XTO
RX2 Decoder X’tal
Selector
RX3 Oscillator
XTI
LISEL IPS0/1, OPS0/1 bit
MCLK2
LOPIN
LIN1
LIN2
LIN3 ADC MCKO
HPF,
LIN4 ADC Audio
LIN5 DVOL PORTB
LIN6 I/F
LIN0/1/2, RIN0/1/2 bit BICKB
RIN1 LRCKB
RIN2 DIR
RIN3
RIN4 HPF, ADC
ADC SDOUT SDTOB
RIN5 DVOL SDTIA1
RIN6 off
ROPIN SDTOB0/1 bit
RISEL SDTIB
Through DIR
ADC I2C
TX DIT
DIT SDTIB
DIT bit SDTIA1 CSN
DIR µP I/F CCLK
DIT0/1 bit
ADC CDTI
LOUT1 SDTIB CDTO
LPF DAC DVOL DAC1
SDTIA1
Audio SDTIA2
ROUT1 LPF DAC DVOL I/F SDTIA3
DIR DIR PORTA

LPF DAC DVOL DAC2 ADC ADC

LOUT2 SDTOA
Audio SDTIB SDTIB
OLRCKA
SDTIA1 off
ROUT2 LPF DAC DVOL I/F
SDTIA2 SDTOA0/1 bit BICKA
SDTIA3
ILRCKA
HPL DAC10/11/12,
DAC20/21/22 bit SDTIA1
SDTIA2
HPR
SDTIA3

Figure 7-1 BLOCK DIAGRAM OF IC

AVDD1
AVSS1
PVSS

RIN4

RIN3

RIN2

RIN1
RIN6

RIN5
LIN5

LIN4

LIN1
LIN6

LIN3

LIN2
R

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
PVDD 1 48 RISEL
RX0 2 47 ROPIN
I2C 3 46 LOPIN
RX1 4 45 LISEL
RX2 5 44 AVSS2
RX3 6 43 AVDD2
INT 7 42 VCOM
VOUT 8
AK4683EQ 41 ROUT2
CDTO 9 40 LOUT2
LRCKB 10 39 ROUT2
BICKB 11 38 LOUT2
SDTOB 12 37 MUTET
OLRCKA 13 36 HPL
ILRCKA 14 35 HPR
BICKA 15 34 HVSS
SDTOA 16 33 HVDD
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
TVDD

DVDD

MCLK2
PDN

CSN
XTO

SDTIA1
SDTIA2
SDTIA3
MCKO

SDTIB
DVSS

TX

CCLK
XTI

CDTI

Figure 7-2 PIN CONFIGURATION OF IC

7–1
 HT-SB300
IC300 VHiAK4683EQ-1 : Multi-Channel Audio Codec ( AK4683EQ ) ( 2/3 )
PIN NAME Input / Output DESCRIPTION
1 PVDD --- PLL Power supply Pin,4.5V ~ 5.5V
2 RX0 Input Receiver Channel 0 Pin (Internal biased pin. Internally biased at PVDD/2)
3 12C Input Control Mode Select Pin. "L": 4-wire Serial, "H": I²C Bus
4 RX1 Input Receiver Channel 1 Pin
5 RX2 Input Receiver Channel 2 Pin
6 RX3 Input Receiver Channel 3 Pin
7 INT Output Interrupt Pin
VOUT Output V-bit Output Pin for Receiver Input
Zero Input Detect Pin.
DZF Output When the input data of DAC follow total 8192 LRCK cycles with "0" input data, this
8
pin goes to "H". And when RSTN1 bit is "0", PWDA bit is "0", this pin goes to "H".
Analogue Input Overflow Detect Pin.
OVF Output
This pin goes to "H" if the analogue input of Lch or Rch overflows.
9 CDTO Output Control Data Output Pin in Serial Mode and 12C pin = "L".
10 LRCKB Input / Output Channel Clock B Pin
11 BICKB Input / Output Audio Serial Data Clock B Pin
12 SDTOB Output Audio Serial Data Output B Pin
13 OLRCKA Input / Output Output Channel Clock A Pin
14 ILRCKA Input / Output Input Channel Clock A Pin
15 BICKA Input / Output Audio Serial Data Clock A Pin
16 SDTOA Output Audio Serial Data Output A Pin
17 MCKO Output Master Clock Output Pin
18 TVDD --- Output Buffer Power Supply Pin, 2.7V ~ 5.5V
19 DVSS --- Digital Ground Pin, 0V
20 DVDD --- Digital Power Supply Pin, 4.5V ~ 5.5V
21 XTI Input Crystal Input Pin
22 XTO Output Crystal Output Pin
Transmit Channel Output pin
23 TX Output When DIT bit = "0", RXO ~ 3 Through
When DIT bit = "1", Internal DIT Output
24 MCLK2 Input Master Clock Input Pin
Power-Down Mode & Reset Pin
25 PDN Output When "L", the AK4683 is powered down, all registers are reset. And then all digital
output pins go "L". The AK4683 must be reset once upon power-up.
CDTI Input Control Data Input Pin in Serial Mode and 12C pin = "L".
26
SDA Input / Output Control Data Pin in Serial Mode and 12C pin = "H".
CCLK Input Control Data Clock Pin in Serial Mode and 12C pin = "L".
27
SCL Input Control Data Clock Pin in Serial Mode and 12C pin = "H".
CSN Input Chip Select Pin in Serial Mode and 12C pin = "L".
28
TEST Input This pin should be connected to DVSS in Serial Mode and 12C pin = "H".
29 SDTIA1 Input Audio Serial Data Input A1 Pin
30 SDTIA2 Input Audio Serial Data Input A2 Pin
31 SDTIA3 Input Audio Serial Data Input A3 Pin
32 SDTIB Input Audio Serial Data Input B Pin
33 HVDD --- HP Power Supply Pin, 4.5V ~ 5.5V
34 HVSS --- HP Ground Pin, 0V
35 HPR Output HP Rch Output Pin
36 HPL Output HP Lch Output Pin
HP Common Voltage Output Pin
37 MUTET ---
1µF capacitor should be connected to HVSS externally.
38 LOUT2 Output DAC2 Lch Positive Analogue Output Pin
39 ROUT2 Output DAC2 Rch Positive Analogue Output Pin
40 LOUT1 Output DAC1 Lch Positive Analogue Output Pin
41 ROUT1 Output DAC1 Rch Positive Analogue Output Pin
DAC / ADC Common Voltage Output Pin
42 VCOM ---
2.2µF capacitor should be connected to AVSS2 externally.
43 AVDD2 --- DAC Power Supply Pin, 4.5V ~ 5.5V
44 AVSS2 --- DAC Ground Pin, 0V
45 LISEL Output Lch Feedback Resistor Output Pin
46 LOPIN Output Lch Feedback Resistor Input Pin. 0.5V x AVDD1

7–2
HT-SB300
IC300 VHiAK4683EQ-1 : Multi-Channel Audio Codec ( AK4683EQ ) ( 3/3 )
PIN NAME Input / Output DESCRIPTION
47 ROPIN Output Rch Feedback Resistor Input Pin. 0.5V x AVDD1
48 RISEL Output Rch Feedback Resistor Output Pin
49 AVSS1 --- ADC Ground Pin, 0V
50 AVDD1 --- ADC Power Supply Pin, 4.5V ~ 5.5V
51 LIN1 Input Lch Input 1 Pin
52 RIN1 Input Rch Input 1 Pin
53 LIN2 Input Lch Input 2 Pin
54 RIN2 Input Rch Input 2 Pin
55 LIN3 Input Lch Input 3 Pin
56 RIN3 Input Rch Input 3 Pin
57 LIN4 Input Lch Input 4 Pin
58 RIN4 Input Rch Input 4 Pin
59 LIN5 Input Lch Input 5 Pin
60 RIN5 Input Rch Input 5 Pin
61 LIN6 Input Lch Input 6 Pin
62 RIN6 Input Rch Input 6 Pin
63 PVSS --- PLL Ground Pin
External Resistor Pin
64 R ---
12 k +/-1% resistor should be connected to PVSS externally.

Note: All input pins except internal biased pin (RX0) and analogue input pins (LIN1 ~ 6, RIN1 ~ 6) should not be left floating.

7–3
 HT-SB300
IC501 RH-IXA230AW00 : System Microcomputer ( IXA230AW ) ( 1/5 )
Pin NAME INPUT / SOFT
FORM FUNCTION OUTLINE
No. PORT_TYPE OUTPUT PULL-UP
NO USE CMOS INPUT
1 OUTPUT Fix " L"
P96/ANEX1 / OUTPUT
NO USE CMOS INPUT
2 OUTPUT OFF Fix " L"
P95/ANEX0 / OUTPUT
NO USE CMOS INPUT
3 OUTPUT Fix " L"
P94 / OUTPUT
NO USE CMOS INPUT
4 OUTPUT Fix " L"
P93 / OUTPUT
NO USE CMOS INPUT
5 OUTPUT Fix " L"
P92/TB2IN / OUTPUT
OFF
NO USE CMOS INPUT
6 OUTPUT Fix " L"
P91/TB1IN / OUTPUT
NO USE CMOS INPUT
7 OUTPUT Fix " L"
P90/TB1IN / OUTPUT
BYTE
8 INPUT INPUT - Connect to VSS(GND)
BYTE
CNVSS
9 INPUT INPUT - Pull-down Connect to VSS(GND)
CNVSS
XCIN CMOS INPUT
10 INPUT Subclock 32.768kHz
P87/XCIN / OUTPUT
OFF
XCOUT CMOS INPUT
11 OUTPUT Subclock 32.768kHz
P86/XCOUT / OUTPUT
RESET
12 INPUT INPUT - Micom RESET
RESET
X_OUT CMOS
13 OUTPUT - Main Clock 9.8MHz
XOUT OUTPUT
GND
14 -- -- - Connect to VSS(GND)
VSS
X_IN
15 INPUT CMOS INPUT - Main Clock 9.8MHz
XIN
VCC Micon Supply 3.3V
16 -- -- -
VCC1 Back-up Supply
NMI
17 INPUT CMOS INPUT - Pull-UP Connect to VCC
P85/NMI
NO USE CMOS INPUT
18 OUTPUT OFF Fix " L"
P84/INT2 / OUTPUT
SYS_STOP CMOS INPUT
19 INPUT [INT1] AC Power Fail Detection
P83/INT1 / OUTPUT
RX_IN CMOS INPUT
20 INPUT [INT0] Remote Control input
P82/INT0 / OUTPUT
OFF
NO USE CMOS INPUT
21 OUTPUT Fix " L"
P81 / OUTPUT
NO USE CMOS INPUT
22 OUTPUT Fix " L"
P80 / OUTPUT
NO USE CMOS INPUT
23 OUTPUT Fix " L"
P77 / OUTPUT
NO USE CMOS INPUT
24 OUTPUT OFF Fix " L"
P76 / OUTPUT
NO USE CMOS INPUT
25 OUTPUT Fix " L"
P75/TA2IN / OUTPUT
NO USE CMOS INPUT
26 INPUT OFF FIX " L"
P74/TA2OUT / OUTPUT
NO USE CMOS INPUT
27 INPUT FIX " L"
P73/CTS2/RTS2/TA1IN / OUTPUT
OFF
NO USE CMOS INPUT
28 OUTPUT FIX " L"
P72/CLK2/TA1OUT / OUTPUT
NO USE
29 OUTPUT Nch OPEN - FIX " L"
P71/RXD2/SCL2/TA0IN
NO USE INPUT /
30 Nch OPEN - FIX " L"
P70/TXD2/SDA2/TA0OUT OUTPUT
FLASH_TXD CMOS INPUT
31 OUTPUT OFF FLASH Writer Data Output
P67/TXD1/SDA1 / OUTPUT

7–4
HT-SB300
IC501 RH-IXA230AW00 : System Microcomputer ( IXA230AW ) ( 2/5 )
Pin NAME INPUT / SOFT
FORM FUNCTION OUTLINE
No. PORT_TYPE OUTPUT PULL-UP
FLASH_RXD CMOS INPUT
32 INPUT FLASH Writer Data input
P66/RXD1/SCL1 / OUTPUT
FLASH_SCLK CMOS INPUT
33 OUTPUT FLASH Writer CLK input
P65/CLK1 / OUTPUT OFF
FLASH_BUSY
CMOS INPUT
34 P64/CTS1/RTS1/CTS0/ OUTPUT FLASH Writer BUSY output. BUSY"H"
/ OUTPUT
CLKS1
DB_SDA INPUT / CMOS INPUT
35 [I2Cbus]DOLBY IC IF Data I/O
P63/TXD0/SDA0 OUTPUT / OUTPUT
DB_SCL CMOS INPUT
36 OUTPUT [I2Cbus]DOLBY IC IF CLK
P62/RXD0/SCL0 / OUTPUT
OFF
DB_RESET CMOS INPUT
37 OUTPUT Dolby RESET
P61/CLK0 / OUTPUT
DB_SCP_IRQ CMOS INPUT
38 INPUT DOLBY IC(OPTION)
P60/CTS0/RTS0 / OUTPUT
NO USE CMOS INPUT
39 OUTPUT FIX " L"
P57/CLKOUT / OUTPUT
DB_SCP_BSY CMOS INPUT
40 INPUT DOLBY IC(OPTION)
P56 / OUTPUT
OFF
FLASH_EPW CMOS INPUT
41 INPUT Pull-down Connect to VSS(GND)
P55 / OUTPUT
NO USE CMOS INPUT
42 OUTPUT FIX " L"
P54 / OUTPUT
NO USE CMOS INPUT
43 OUTPUT FIX " L"
P53 / OUTPUT
NO USE CMOS INPUT
44 OUTPUT FIX " L"
P52 / OUTPUT
OFF
NO USE CMOS INPUT
45 OUTPUT FIX " L"
P51 / OUTPUT
FLASH_CE CMOS INPUT
46 INPUT Pull-UP Connect to VCC
P50 / OUTPUT
Reset audio when
PWM IN CMOS INPUT Analog = LVL DETECT H and PWM IN L
47 INPUT
/ OUTPUT Digital = PLL LOCK and PWM IN L
P47
AMP_INT CMOS INPUT
48 INPUT OFF
P46 / OUTPUT
AMP_RESET CMOS INPUT
49 OUTPUT
P45 / OUTPUT
AMP_PWRDN CMOS INPUT
50 OUTPUT
P44 / OUTPUT
SDA INPUT / CMOS INPUT [I2Cbus]DIR/ADC&ANALOG SW IF Data I/O
51
P43 OUTPUT / OUTPUT (*1)Nch open-drain
SCL CMOS INPUT [I2Cbus]DIR/ADC&ANALOG SW IF CLK
52 OUTPUT
P42 / OUTPUT (*1)Nch open-drain
OFF
NO USE CMOS INPUT
53 OUTPUT FIX " L"
P41 / OUTPUT
NO USE CMOS INPUT
54 OUTPUT FIX " L"
P40 / OUTPUT
NO USE CMOS INPUT
55 OUTPUT FIX " L"
P37 / OUTPUT
OFF
DIR_INT CMOS INPUT
56 INPUT DIR INT
P36 / OUTPUT
DIR_PDN CMOS INPUT
57 OUTPUT FIX " L"
P35 / OUTPUT
OFF
NO USE CMOS INPUT
58 OUTPUT FIX " L"
P34 / OUTPUT
NO USE CMOS INPUT
59 OUTPUT FIX " L"
P33 / OUTPUT
NO USE CMOS INPUT
60 INPUT OFF FIX " L"
P32 / OUTPUT
NO USE CMOS INPUT
61 INPUT FIX " L"
P31 / OUTPUT

7–5
 HT-SB300
IC501 RH-IXA230AW00 : System Microcomputer ( IXA230AW ) ( 3/5 )
Pin NAME INPUT / SOFT
FORM FUNCTION OUTLINE
No. PORT_TYPE OUTPUT PULL-UP
VCC Micon Supply 3.3V
62 -- -- -
VCC2 Back-up Supply
NO USE CMOS INPUT
63 OUTPUT FIX " L"
P30 / OUTPUT
GND
64 -- -- - Connect to VSS(GND)
VSS
NO USE CMOS INPUT
65 OUTPUT FIX " L"
P27 / OUTPUT
NO USE CMOS INPUT
66 OUTPUT FIX " L"
P26 / OUTPUT
OFF
NO USE CMOS INPUT
67 OUTPUT FIX " L"
P25 / OUTPUT
NO USE CMOS INPUT
68 OUTPUT FIX " L"
P24 / OUTPUT
NO USE CMOS INPUT
69 OUTPUT FIX " L"
P23 / OUTPUT
NO USE CMOS INPUT
70 INPUT FIX " L"
P22 / OUTPUT
OFF
NO USE CMOS INPUT
71 INPUT FIX " L"
P21 / OUTPUT
NO USE CMOS INPUT
72 OUTPUT FIX " L"
P20 / OUTPUT
NO USE CMOS INPUT
73 OUTPUT FIX " L"
P17 / OUTPUT
NO USE CMOS INPUT
74 OUTPUT FIX " L"
P16/INT4 / OUTPUT
OFF
LED_ON CMOS INPUT
75 OUTPUT POWER LED "ON" CTRL
P15/INT3 / OUTPUT
LED_STBY CMOS INPUT
76 OUTPUT POWER LED "STDBY" CTRL
P14 / OUTPUT
STBY_DRIVER CMOS INPUT
77 OUTPUT LED DRIVER Comm.STB signal
P13 / OUTPUT
DOUT_DRIVER CMOS INPUT
78 INPUT LED DRIVER Comm. DATA input
P12 / OUTPUT
OFF
DIN_DRIVER CMOS INPUT
79 OUTPUT LED DRIVER Comm. Command
P11 / OUTPUT
CLK_DRIVER CMOS INPUT
80 OUTPUT LED DRIVER Comm. Sync CLK output
P10 / OUTPUT
LVL_DETECT INPUT ANA-
CMOS INPUT
81 LOG LEVEL DETECT
P07/AN07 / OUTPUT
/ DIGITAL
AVCK1 INPUT ANA-
CMOS INPUT
82 LOG [AD]D1.8V Abnormal Voltage Detection
P06/AN06 / OUTPUT
/ DIGITAL OFF
AVCK2 INPUT ANA-
CMOS INPUT
83 LOG [AD]A3.3V Abnormal Voltage Detection
P05/AN05 / OUTPUT
/ DIGITAL
NO USE CMOS INPUT
84 OUTPUT FIX " L"
P04/AN04 / OUTPUT
NO USE CMOS INPUT
85 INPUT FIX " L"
P03/AN03 / OUTPUT
NO USE CMOS INPUT
86 OUTPUT FIX " L"
P02/AN02 / OUTPUT
OFF
NO USE CMOS INPUT
87 OUTPUT FIX " L"
P01/AN01 / OUTPUT
NO USE CMOS INPUT
88 OUTPUT FIX " L"
P00/AN00 / OUTPUT

7–6
HT-SB300
IC501 RH-IXA230AW00 : System Microcomputer ( IXA230AW ) ( 4/5 )
Pin NAME INPUT / SOFT
FORM FUNCTION OUTLINE
No. PORT_TYPE OUTPUT PULL-UP
NO USE CMOS INPUT
89 OUTPUT FIX " L"
P107/AN7/Ki3 / OUTPUT
POWER (DC RELAY) CMOS INPUT (DC_RELAY) MAIN POWER CONTROLHPOWER
90 OUTPUT
P106/AN6/Ki2 / OUTPUT ONLPOWER OFF
SYS-PROTECT INPUT ANA- OFF
CMOS INPUT
91 LOG SYSTEM Supply Abnormal Detection
P105/AN5/Ki1 / OUTPUT
/ DIGITAL
KEY_POWER CMOS INPUT
92 INPUT POWER KEY
P104/AN4/Ki0 / OUTPUT
KEY1 INPUT ANA-
CMOS INPUT
93 LOG [A/D]KEYS input
P103/AN3 / OUTPUT
/ DIGITAL
NO USE CMOS INPUT
94 OUTPUT FIX " L"
P102/AN2 / OUTPUT
AREA INPUT ANA-
CMOS INPUT
95 LOG Destination
P101/AN1 / OUTPUT
/ DIGITAL
GND VSS A/D reference port.
96 -- -- -
AVSS Connect to GND(VSS)
NO USE CMOS INPUT
97 OUTPUT FIX " L"
P100/AN0 / OUTPUT
VREF Voltage A/D reference port.
98 -- -- -
VREF Connect to VCC.
AVCC Supply A/D reference port.
99 -- -- -
AVCC Connect to VCC.
NO USE CMOS INPUT
100 OUTPUT FIX " L"
P97/ADTRG / OUTPUT

7–7
 HT-SB300
IC501 RH-IXA230AW00 : System Microcomputer ( IXA230AW ) ( 5/5 )

POWER(DC RELAY)
SYS_PROTECT
KEY_POWER

LVL_DETECT
NO USE

NO USE

NO USE

NO USE

NO USE

NO USE

NO USE

NO USE

NO USE

AVCK2

AVCK1
AVCC

AREA
VREF

KEY1
GND
P97/ADTRG 100

AVCC 99

VREF 98

P100/AN0 97

AVSS 96

P101/AN1 95

P102/AN2 94

P103/AN3 93

P104/AN4/KI0 92

P105/AN5/KI1 91

P106/AN6/KI2 90

P107/AN7/KI3 89

P00/AN00 88

P01/AN01 87

P02/AN02 86

P03/AN03 85

P04/AN04 84

P05/AN05 83

P06/AN06 82

P07/AN07 81
NO USE 1 P96/ANEX1 P10 80 CLK_DRIVER

NO USE 2 P95/ANEX0 P11 79 DIN_DRIVER

NO USE 3 P94 P12 78 DOUT_DRIVER

NO USE 4 P93 P13 77 STBY_DRIVER

NO USE 5 P92/T B2IN P14 76 LED_STBY

NO USE 6 P91/T B1IN P15/INT3 75 LED_ON

NO USE 7 P90/T B1IN P16/INT4 74 NO USE

BYTE 8 BYTE P17 73 NO USE

CNVSS 9 CNVSS P20 72 NO USE

XCIN 10 P87/XCIN P21 71 NO USE

XC OUT 11 P86/XC OUT P22 70 NO USE

RESET 12 RESET P23 69 NO USE

IXA230A
X_OUT 13 XOUT SHARP P24 68 NO USE

GND 14 VSS P25 67 NO USE

X_IN 15 XIN P26 66 NO USE

VCC 16 VCC1 P27 65 NO USE

NMI 17 P85/NMI VSS 64 GND

NO USE 18 P84/INT2 P30 63 NO USE

SYS_STOP 19 P83/INT1 VCC2 62 VCC

RX_IN 20 P82/INT0 P31 61 NO USE

NO USE 21 P81 P32 60 NO USE

NO USE 22 P80 P33 59 NO USE

NO USE 23 P77 P34 58 NO USE

NO USE 24 P76 P35 57 DIR_PDN

NO USE 25 P75/TA2IN P36 56 DIR_INT

NO USE 26 P74/TA2OUT P37 55 NO USE

P73/CTS2/RTS2/
NO USE 27 P40 54 NO USE
TA1IN
P72/CLK2/TA1
NO USE 28 P41 53 NO USE
OUT
P71/RXD2/SCL2/
NO USE 29 P42 52 SCL
TA0IN
P70/TXD2/SDA2/
NO USE 30 P43 51 SDA
TA0OUT
P64/CTS1/RTS1/CT
31 P67/TXD1/SDA1

32 P66/RXD1/SCL1

35 P63/TXD0/SDA0

36 P62/RXD0/SCL0

38 P60/CTS0/RTS0

39 P57/CLKOUT
S0/CLKS1
33 P65/CLK1

37 P61/CLK0

40 P56

41 P55

42 P54

43 P53

44 P52

45 P51

46 P50

47 P47

48 P46

49 P45

50 P44
34

AMP_INT
DB_SCP_IRQ
FLASH_BUSY

DB_SCP_BSY
DB_RESET

FLASH_EPM

AMP_RESET
DB_SCL
FLASH_TXD

FLASH_RXD

FLASH_SCLK

DB_SDA

NO USE

NO USE

NO USE

NO USE

NO USE

FLASH_CE

PWM IN

AMP_PWRDN

Figure 7-3 BLOCK DIAGRAM OF IC

7–8
HT-SB300
IC701 VHiPT6965++-1 : 7 Segment Driver ( PT6965 ) ( 1/2 )

SG1/KS1
SG2/KS2
SG3/KS3
Control
DIN SG4/KS4
DOUT Serial SG5/KS5
Data Display
CLK SG6/KS6
Interface Memory
STB SG7/KS7
SG8/KS8
Segment Driver/ SG9/KS9
OSC Key Scan Output/
OSC Timing Generator
Grid Driver SG10/KS10
R SG11
Key Matrix SG12/GR7
Memory Dimming Circuit
SG13/GR6
SG14/GR5
GR4
GR3
GR2
GR1

K1 K2 VDD GND

Figure 7-4 BLOCK DIAGRAM OF IC

OSC 1 30 GND
DOUT 2 29 GR1
DIN 3 28 GR2
CLK 4 27 GND
STB 5 26 GR3
K1 6 25 GR4
K2 7 24 GND
VDD 8 PT6965 23 VDD
SG1/KS1 9 22 SG14/GR5
SG2/KS2 10 21 SG13/GR6
SG3/KS3 11 20 SG12/GR7
SG4/KS4 12 19 SG11
SG5/KS5 13 18 SG10/KS10
SG6/KS6 14 17 SG9/KS9
SG7/KS7 15 16 SG8/KS8

Figure 7-5 PIN CONFIGURATION OF IC

7–9
 HT-SB300
IC701 VHiPT6965++-1 : 7 Segment Driver ( PT6965 ) ( 2/2 )
PIN NAME Input / Output DESCRIPTION
Oscillator Input Pin
1 OSC Input
A resistor is connected to this pin to determine the oscillation frequency.
Data Output Pin (N-Channel, Open-Drain)
2 DOUT Output
This pin outputs serial data at the falling edge of the shift clock.
Data Input Pin
3 DIN Input
This pin inputs serial data at the rising edge of the shift clock (starting from the lower bit)
Clock Input Pin
4 CLK Input
This pin ireads serial data at the rising edge and outputs data at falling edge.
Serial Interface Strobe Pin
5 STB Input The data input after the STB has fallen is processed as a command. When this pin is
"HIGH", CLK is ignored.
Key Data Input Pins
6,7 K1 to K2 Input The data sent to these pins are latched at the end of the display cycle.
(Internal Pull-Low Resistor)
8,23 VDD --- Power Supply
SG1/KS1 to SG10/ Segment Output Pins (P-Channel, Open-Drain)
9 ~ 18 Output
KS10 Also acts as the Key Source.
19 SG11 Output Segment Output Pins (P-Channel, Open-Drain)
SG12/GR7 to SG14/
20 ~ 22 Output Segment / Grid Output Pins
GR5
24,27,30 GND --- Ground Pin
25, 26,
GR4 to GR1 Output Grid Output Pins
28, 29

7 – 10
HT-SB300
IC901 VHISTA333BW-1 : 2.1 Channels High Efficiency Digital Audio System ( STA333BW ) ( 1/2 )

SCL SDA CONFIG

SA
I2C

OUT1A
OUT1B
SDI POWER OUT2A
LRCKI Serial Data Input OUT2B

BICKI Channel mapping

CONTROL
STATUS

RESET
EQ, Tone, DDX3A
INT LINE Volumes... DDX3B
DDX4A/TWARNEXT
PWDN DDX4B/EAPD
Processor

XTI
PLL

PLL_FILTER

Figure 7-6 BLOCK DIAGRAM OF IC

GND_SUB 1 36 Vdd_DIG

SA 2 35 GND_DIG

TEST MODE 3 34 SCL

VSS 4 33 SDA

VCC_REG 5 32 INT_LINE

OUT2B 6 31 RESET

GND2 7 30 SDI

Vcc2 8 29 LRCKI

OUT2A 9 28 BICKI

OUT1B 10 27 XTI

Vcc1 11 26 PLL_GND

GND1 12 25 PLL_FILTER

OUT1A 13 24 PLL_Vdd

GND_REG 14 23 POWRDN

Vdd 15 22 GND_DIG

CONFIG 16 21 VDD_DIG

OUT3B/DDX3B 17 20 TWARN/OUT4B

OUT3A/DDX3A 18 19 EAPD/OUT4B

Figure 7-7 PIN CONFIGURATION OF IC

7 – 11
 HT-SB300
IC901 VHISTA333BW-1 : 2.1 Channels High Efficiency Digital Audio System ( STA333BW ) ( 2/2 )

PIN NAME TYPE DESCRIPTION

1 GND_SUB Input / Output Subtrate ground
2 SA Input I²C Select Address
3 Test_Mode Input This pin must be connected to GROUND
4 Vss Input / Output Internal reference at Vcc - 3.3V
5 Vcc_REG Input / Output Internal Vcc reference
6 OUT2B Output Output half bridge 2B
7 GND2 Input / Output Power negative supply
8 Vcc2 Input / Output Power positive supply
9 OUT2A Output Output half bridge 2A
10 OUT1B Output Output half bridge 1B
11 Vcc1 Input / Output Power positive supply
12 GND1 Input / Output Power negative supply
13 OUT1A Input / Output Output half bridge 1A
14 GND_REG Input / Output Internal Ground reference
15 Vdd Input / Output Internal 3.3V reference voltage
16 CONFIG Input Paralleled mode command
17 OUT3B/DDX3B Output PWM Out CH3B - External Bridge
18 OUT3A/DDX3A Output PWM Out CH3A - External Bridge
19 EAPD/OUT4A Output Power Down for External Bridge
20 TWARN/OUT4B Input Thermal warning from External Bridge
21 Vdd_DIG Input / Output Positive Supply Digital
22 GND_DIG Input / Output Digital Ground
23 PWRDN Input Power Down
24 PLL_Vdd Input / Output Positive Supply for PLL
25 PLL_FILTER Input Connection to PLL Filter
26 PLL_GND Input / Output Negative Supply for PLL
27 XTI Input PLL Input Clock
28 BICKI Input I²S Serial Clock
29 LRCKI Input I²S Left / Right Clock
30 SDI_12 Input I²S Serial Data Channels 1&2
31 RESET Input Reset
32 INT_LINE Output Fault Interrupt
33 SDA Input / Output I²C Serial Data
34 SCL Input I²C Serial Clock
35 GND_DIG Input / Output Digital Ground
36 Vdd_DIG Input / Output Digital Supply

7 – 12
HT-SB300
IC902 VHISTA533W+-1 : 2.2A QUAD POWER HALF BRIDGE ( STA533W ) ( 1/2 )

GND-SUB 1 36 VccSign

OUT2B 2 35 VccSign
OUT2B 3 34 Vss
Vcc2B 4 33 Vss
GND2B 5 32 IN2B
GND2A 6 31 IN2A
Vcc2A 7 30 IN1B
OUT2A 8 29 IN1A
OUT2A 9 28 TH_WAR
OUT1B 10 27 FAULT
OUT1B 11 26 TRI-STATE
Vcc1B 12 25 PWRDN
GND1B 13 24 CONFIG
GND1A 14 23 VL

Vcc1A 15 22 VDD
OUT1A 16 21 VDD
OUT1A 17 20 GND-Reg
N.C. 18 19 GND-Clean

D04AU1564

Figure 7-8 BLOCK DIAGRAM OF IC

7 – 13
 HT-SB300
IC902 VHISTA533W+-1 : 2.2A QUAD POWER HALF BRIDGE ( STA533W ) ( 2/2 )
PIN NAME DESCRIPTION
1 GND_SUB Subtrate ground
2;3 OUT2B Output half bridge 2B
4 Vcc2B Positive Supply
5 GND2B Negative supply
6 GND2A Negative supply
7 Vcc2A Positive Supply
8;9 OUT2A Output half bridge 2A
10 ; 11 OUT1A Output half bridge 1B
12 Vcc1B Positive Supply
13 GND1B Negative supply
14 GND1A Negative supply
15 Vcc1A Positive Supply
16 ; 17 OUT1A Output half bridge 1A
18 NC Not Connected
19 GND-clean Logical Ground
20 GND-Reg Ground for regulator Vdd
21 ; 22 Vdd 5V Regulator referred to ground
23 VL Logic Reference Voltage
24 CONFIG Configuration pin
25 PWRDN Stand-by pin
26 TRI-STATE Hi-Z pin
27 FAULT Fault pin advisor
28 TH-WAR Thermal warning advisor
29 IN1A Input half bridge 1A
30 IN1B Input half bridge 1B
31 IN2A Input half bridge 2A
32 IN2B Input half bridge 2B
33 ; 34 Vss 5V Regulator referred to +Vcc
35 ; 36 Vcc Sign Signal Positive Supply

7 – 14
HT-SB300
-MEMO-

7 – 15
 HT-SB300

PARTS GUIDE

SOUND BAR SYSTEM

MODEL HT-SB300

CONTENTS

[1] INTEGRATED CIRCUITS [7] RESISTORS

[2] TRANSISTORS [8] OTHER CIRCUITRY PARTS

[3] DIODES [9] CABINET PARTS

[4] COILS [10] ACCESSORIES / PACKING

PARTS
[5] CRYSTALS / VIBRATORS
[11] P.W.B. ASSEMBLY
[6] CAPACITORS (Not Replacement Item)

Parts marked with " ! " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

This document has been published to be used for

SHARP CORPORATION after sales service only.
The contents are subject to change without notice.
HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[1] INTEGRATED CIRCUITS

iC101 VHiCS495313-1 BH DSP iC 32 BiT 16CH PCM
iC300 VHiAK4683EQ-1 AW Multi-Ch Audio Codec
iC301 VHiTC7WU04U-1 AG 22240935R2 TC7WU04FU
iC501 RH-iXA230AW00 AY System Microcomputer,iXA230AW
iC502 VHiPST8227N-1 AC Reset iC
iC701 VHiPT6965++-1 AK 7 Segment Driver
iC801 VHiLV5805M+-1 AG DC - DC Converter
iC803 VHiKiA1117F33 AF Voltage Regulator,3.3V
iC804 VHiKiA1117F18 AG Voltage Regulator,1.8V
iC805 VHiAP2213M33E AE Voltage Regulator, 3.3V
iC806 VHiAZ4558CME1 AD Operational Amplifier
iC901 VHiSTA333BW-1 AW Digital Amplifier
iC902 VHiSTA533W+-1 AP 2.2A Quad Power Half Bridge
[2] TRANSISTORS
Q300 VS2SD601AR/-1 AC Switching Transistor
Q301 VSKRA107S//-1 AB Digital,PNP,KRA107 S
Q500 VSKRC104S//-1 AC Digital,NPN,KRC104 S
Q501 VSKRC104S//-1 AC Digital,NPN,KRC104 S
Q700 VSKRC101S//-1 AB Digital,NPN,KRC101 S
Q701 VSKRC101S//-1 AB Digital,NPN,KRC101 S
Q800 VSKRC107S//-1 AB Digital,NPN,KRC107 S
Q801 VSKMS6D0P20X1 AF Switching Transistor
Q802 VSKRC104S//-1 AC Digital,NPN,KRC104 S
Q805 VSKRC104S//-1 AC Digital,NPN,KRC104 S
Q806 VSKRC104S//-1 AC Digital,NPN,KRC104 S

[3] DIODES
D300 VHDMA111G++-1 AB Silicon,MA111
D501 VHDMA111G++-1 AB Silicon,MA111
D502 VHDMA111G++-1 AB Silicon,MA111
D503 VHDMA111G++-1 AB Silicon,MA111
D801 VHDMA111G++-1 AB Silicon,MA111
D802 VHDMA111G++-1 AB Silicon,MA111
D804 VHDMA111G++-1 AB Silicon,MA111
D805 VHDMA111G++-1 AB Silicon,MA111
D806 VHDMA111G++-1 AB Silicon,MA111
D807 VHDMA111G++-1 AB Silicon,MA111
D901 VHDMA111G++-1 AB Silicon,MA111
DM101 VHDKDS226//-1 AB Silicon,KDS226
DM102 VHDKDS226//-1 AB Silicon,KDS226
DM104 VHDKDS226//-1 AB Silicon,KDS226
DM105 VHDKDS226//-1 AB Silicon,KDS226
DM302 VHDKDS226//-1 AB Silicon,KDS226
DM303 VHDKDS226//-1 AB Silicon,KDS226
DM304 VHDKDS226//-1 AB Silicon,KDS226
DM305 VHDKDS226//-1 AB Silicon,KDS226
DM501 VHDKDS226//-1 AB Silicon,KDS226
DZ300 RH-EXA523WJZZ AB Zener,5.6V
DZ800 VHDGDSK52B+-1 AE Schotty Barrier
DZ801 VHDSMAB33L+-1 AD Schotty Barrier
DZ802 RH-EXA523WJZZ AB Zener,5.6V
DZ803 RH-EXA507WJZZ AB Zener,3.3V
LED701 VHPKW2402CB-1 AT 7 Segment Blue LED
LED702 VHPCL165SRD-1 AD Dual Chip LED,Red
LED703 VHPACL191NB-1 AD LED,Blue
LED704 VHPACL191NB-1 AD LED,Blue
LED705 VHPACL191NB-1 AD LED,Blue
LED706 VHPACL191NB-1 AD LED,Blue
LED707 VHPACL191NB-1 AD LED,Blue
LED708 VHPACL191NB-1 AD LED,Blue
LED709 VHPACL191NB-1 AD LED,Blue
LED710 VHPACL191NB-1 AD LED,Blue
[4] COILS
FB300 RBLN-0061TAZZ AB Ferrite Bead
FB800 RBLN-0207TAZZ AB Ferrite Bead
L100 VPBNN2R2K0000 AC Coil, 2.2 µH
L302 VPBNN2R2K0000 AC Coil, 2.2 µH
L500 VPBNN100K0000 AC Coil, 10 µH
L501 VPBNN4R7K0000 AC Coil, 4.7 µH
L801 RCILPA085WJZZ AD Coil, 15 µH
L901 RBLN-0061TAZZ AB Ferrite Bead
L902 RBLN-0061TAZZ AB Ferrite Bead
L903 RBLN-0061TAZZ AB Ferrite Bead
L905 RCiLPA084WJZZ AD Coil, 10 µH
L906 RCiLPA084WJZZ AD Coil, 10 µH
L907 RCiLPA762WJQZ AD Coil
L908 RCiLPA762WJQZ AD Coil
L909 RCiLPA762WJQZ AD Coil
L910 RCiLPA762WJQZ AD Coil
L911 RCiLCA022AWZZ AC Coil, 1 µH
L912 RCiLCA022AWZZ AC Coil, 1 µH
L913 RCiLCA022AWZZ AC Coil, 1 µH
L914 RCiLCA022AWZZ AC Coil, 1 µH
L915 RBLN-A007WJZZ AC Ferrite Core

1
 HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[4] COILS
L916 RBLN-A007WJZZ AC Ferrite Core
R116 VPBNN2R2K0000 AC Coil, 2.2 µH
R131 RFILNA007AWZZ AA Ferrite Bead, 220 ohm
R321 RBLN-0061TAZZ AB Ferrite Bead
R347 RFILNA007AWZZ AA Ferrite Bead, 220 ohm
R808 RBLN-0207TAZZ AB Ferrite Bead

[5] CRYSTALS / VIBRATORS

XM101 RCRSCA145WJZZ AE Crystal, 12.2880MHz
XM501 RCRSC0032TAZZ AE Crystal, 32.768kHz
XM502 RFILZA007WJZZ AE Resonator, 12MHz
[6] CAPACITORS
C100 VCKYCZ1CF104Z AB 0.1 µ F,16V
C104 VCKYCZ1CF104Z AB 0.1 µ F,16V
C106 VCKYCZ1CF104Z AB 0.1 µ F,16V
C107 VCKYCZ1CF104Z AB 0.1 µ F,16V
C108 VCKYCZ1CF104Z AB 0.1 µ F,16V
C109 VCKYCZ1CF104Z AB 0.1 µ F,16V
C110 VCKYCZ1CF104Z AB 0.1 µ F,16V
C111 VCKYCZ1CF104Z AB 0.1 µ F,16V
C112 VCKYCZ1CF104Z AB 0.1 µ F,16V
C113 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C114 VCKYCZ1CF104Z AB 0.1 µ F,16V
C115 VCKYCZ1CF104Z AB 0.1 µ F,16V
C116 VCKYCZ1CF104Z AB 0.1 µ F,16V
C118 VCCCCZ1HH470J AB 47 pF (CH),50V
C120 VCCCCZ1HH150J AA 15 pF (CH),50V
C121 VCCCCZ1HH150J AA 15 pF (CH),50V
C122 VCKYCZ1CF104Z AB 0.1 µ F,16V
C123 VCCCCZ1HH270J AA 27 pF (CH),50V
C124 VCKYCZ1CF104Z AB 0.1 µ F,16V
C125 VCKYCZ1CF104Z AB 0.1 µ F,16V
C126 VCKYCZ1CF104Z AB 0.1 µ F,16V
C127 VCKYCZ1CF104Z AB 0.1 µ F,16V
C128 VCKYCZ1CF104Z AB 0.1 µ F,16V
C129 VCEAPS226AF1C AC 22 µ F,16V,Electrolytic
C130 VCKYCZ1CF104Z AB 0.1 µ F,16V
C131 VCEAPS476AF1C AC 47 µ F,16V,Electrolytic
C132 VCKYCZ1CF104Z AB 0.1 µ F,16V
C133 VCKYCZ1CB223K AB 0.022 µ F,16V
C139 VCCCCZ1HH270J AA 27 pF (CH),50V
C140 VCKYCZ1CF104Z AB 0.1 µ F,16V
C141 VCCCCZ1HH220J AA 22 pF (CH),50V
C302 VCKYCZ1CF104Z AB 0.1 µ F,16V
C305 VCEAPS475AF1H AD 4.7 µ F,50V,Electrolytic
C306 VCCCCZ1HH101J AB 100 pF (CH),50V
C307 VCKYCZ1CF104Z AB 0.1 µ F,16V
C308 VCKYCZ1HB102K AB 1000 p F,50V
C309 VCKYCZ1HB102K AB 1000 p F,50V
C312 VCKYCZ1CF104Z AB 0.1 µ F,16V
C313 VCKYCZ1HB471K AA 470 p F,50V
C320 VCKYCZ1HB331K AB 330 p F,50V
C321 VCKYCZ1HB331K AB 330 p F,50V
C322 VCEAPS475AF1H AD 4.7 µ F,50V,Electrolytic
C323 VCEAPS475AF1H AD 4.7 µ F,50V,Electrolytic
C324 VCKYCZ1CF104Z AB 0.1 µ F,16V
C325 VCKYCY1HB104K AD 0.1 µ F,50V
C326 VCEAPS107AF1C AC 100 µ F,16V,Electrolytic
C328 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C329 VCKYCZ1CF104Z AB 0.1 µ F,16V
C330 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C331 VCKYCZ1CF104Z AB 0.1 µ F,16V
C332 VCKYCZ1CF104Z AB 0.1 µ F,16V
C333 VCKYCZ1CF104Z AB 0.1 µ F,16V
C334 VCEAPS107AF1C AC 100 µ F,16V,Electrolytic
C335 VCKYCY1EB105K AB 1 µ F,25V
C336 VCKYCZ1CF104Z AB 0.1 µ F,16V
C337 VCKYCZ1CF104Z AB 0.1 µ F,16V
C338 VCCCCZ1HH330J AB 33pF (CH),50v
C339 VCCCCZ1HH101J AB 100 pF (CH),50V
C340 VCCCCZ1HH101J AB 100 pF (CH),50V
C341 VCKYCZ1CF104Z AB 0.1 µ F,16V
C342 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C343 VCKYCZ1CF104Z AB 0.1 µ F,16V
C344 VCEAPS107AF1C AC 100 µ F,16V,Electrolytic
C345 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C346 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C347 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C348 VCKYCZ1CF104Z AB 0.1 µ F,16V
C349 VCEAPS104AF1H AD 0.1 µ F,50V,Electrolytic
C350 VCKYCZ1CF104Z AB 0.1 µ F,16V
C351 VCKYCZ1CF104Z AB 0.1 µ F,16V
C352 VCCCCZ1HH220J AA 22 pF (CH),50V
C353 VCCCCZ1HH101J AB 100 pF (CH),50V
C354 VCCCCZ1HH330J AB 33pF (CH),50v
C355 VCCCCZ1HH330J AB 33pF (CH),50v
C356 VCKYTV1EB225K AB 2.2 µ F,25V

2
HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[6] CAPACITORS
C357 VCCCCZ1HH220J AA 22 pF (CH),50V
C358 VCKYCY1EB105K AB 1 µ F,25V
C359 VCKYCZ1CF104Z AB 0.1 µ F,16V
C360 VCKYCZ1CF104Z AB 0.1 µ F,16V
C364 VCKYCY1HB102K AA 1000 p F,50V
C500 VCKYCZ1CF104Z AB 0.1 µ F,16V
C501 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C502 VCKYCY1EB105K AB 1 µ F,25V
C503 VCCCCZ1HH220J AA 22 pF (CH),50V
C504 VCCCCZ1HH100D AA 10 pF (CH),50V
C506 VCKYCZ1CF104Z AB 0.1 µ F,16V
C507 VCKYCZ1CF104Z AB 0.1 µ F,16V
C508 VCKYCZ1EB103K AA 0.01 µ F,25V
C509 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C510 VCEAPS475AF1H AD 4.7 µ F,50V,Electrolytic
C512 VCKYCZ1EB103K AA 0.01 µ F,25V
C513 VCKYCZ1CB223K AB 0.022 µ F,16V
C514 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C515 VCEASX0JN227M AC 220 µ F,6.3V,Electrolytic
C516 VCEAPS337AF0J AC 330 µ F,6.3V,Electrolytic
C517 VCEAPS337AF0J AC 330 µ F,6.3V,Electrolytic
C518 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C519 VCKYCZ1HB102K AB 1000 p F,50V
C522 VCKYCZ1HB102K AB 1000 p F,50V
C523 VCKYCY1EB105K AB 1 µ F,25V
C700 VCKYCZ1CF104Z AB 0.1 µ F,16V
C701 VCKYCZ1HB471K AA 470 p F,50V
C702 VCKYCZ1HB471K AA 470 p F,50V
C703 VCKYCZ1HB471K AA 470 p F,50V
C704 VCKYCZ1HB471K AA 470 p F,50V
C705 VCCCCZ1HH101J AB 100 pF (CH),50V
C706 VCKYCZ1CB223K AB 0.022 µ F,16V
C707 VCEAPS476AF1C AC 47 µ F,16V,Electrolytic
C708 VCEASX0JN227M AC 220 µ F,6.3V,Electrolytic
C709 VCKYCY1EB105K AB 1 µ F,25V
C801 RC-KZA195WJZZ AB 10 µ F,10V,Electrolytic
C803 RC-KZA195WJZZ AB 10 µ F,10V,Electrolytic
C804 RC-KZA195WJZZ AB 10 µ F,10V,Electrolytic
C806 VCKYCY1EB105K AB 1 µ F,25V
C807 RC-KZA114WJZZ AB 1 µ F,25V
C808 VCEAPS226AF1C AC 22 µ F,16V,Electrolytic
C809 VCEAPS226AF1C AC 22 µ F,16V,Electrolytic
C811 RC-KZ3028AWZZ AE 22 µ F,16V,Electrolytic
C812 VCKYCZ1CB223K AB 0.022 µ F,16V
C814 VCKYCZ1CF104Z AB 0.1 µ F,16V
C815 VCKYCZ1CF104Z AB 0.1 µ F,16V
C817 VCCCCZ1HH101J AB 100 pF (CH),50V
C818 VCKYTV1EB225K AB 2.2 µ F,25V
C820 VCKYCZ1CF104Z AB 0.1 µ F,16V
C821 VCKYCZ1CF104Z AB 0.1 µ F,16V
C824 VCEAPS106AF1C AB 10 µ F,16V,Electrolytic
C825 VCKYCY1EB105K AB 1 µ F,25V
C826 VCEAPS225AF1H AB 2.2 µ F,50V,Electrolytic
C827 VCCCCZ1HH101J AB 100 pF (CH),50V
C828 VCKYCY1EB105K AB 1 µ F,25V
C830 RC-KZA383WJZZ AC 10 µ F,25V,Electrolytic
C831 RC-KZA383WJZZ AC 10 µ F,25V,Electrolytic
C832 VCKYCZ1CB153K AB 0.015 µ F,16V
C833 VCKYCZ1HB152K AA 1500 p F,50V
C834 VCKYCZ1HB102K AB 1000 p F,50V
C835 VCKYCZ1CF104Z AB 0.1 µ F,16V
C836 VCKYCY1EB105K AB 1 µ F,25V
C837 VCKYCY1EB105K AB 1 µ F,25V
C838 VCCCCZ1HH221J AB 220 pF (CH),50V
C839 VCCCCZ1HH221J AB 220 pF (CH),50V
C903 VCKYCY1EB105K AB 1 µ F,25V
C904 RC-EZ3129AWZZ AF 1000 µ F,16V,Electrolytic
C906 VCKYCY1HB104K AD 0.1 µ F,50V
C908 VCKYCY1HB104K AD 0.1 µ F,50V
C909 VCKYCY1HB104K AD 0.1 µ F,50V
C910 VCEASX1CN477M AE 470 µ F,16V,Electrolytic
C912 VCKYCZ1HB472K AC 4700 p F,50V
C913 VCKYCY1HB104K AD 0.1 µ F,50V
C915 VCKYCY1EB105K AB 1 µ F,25V
C916 VCKYCY1HB104K AD 0.1 µ F,50V
C917 VCKYCY1HB104K AD 0.1 µ F,50V
C918 VCKYCZ1HB681K AB 680 p F,50V
C919 VCKYCY1HB104K AD 0.1 µ F,50V
C920 VCCCCY1HH101J AA 100 pF (CH),50V
C921 VCCCCY1HH101J AA 100 pF (CH),50V
C922 VCKYCY1HB102K AA 1000 p F,50V
C923 VCKYCY1HB102K AA 1000 p F,50V
C924 VCKYCY1HB104K AD 0.1 µ F,50V
C925 VCEAPS105AF1H AB 1 µ F,50V,Electrolytic
C926 VCKYCY1HB104K AD 0.1 µ F,50V
C927 VCEAPS105AF1H AB 1 µ F,50V,Electrolytic
C928 VCKYCY1EB105K AB 1 µ F,25V
C929 VCKYCY1HB104K AD 0.1 µ F,50V

3
 HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[6] CAPACITORS
C930 VCKYCY1HB104K AD 0.1 µ F,50V
C931 VCKYCY1HB104K AD 0.1 µ F,50V
C932 VCKYCY1HB104K AD 0.1 µ F,50V
C933 VCKYCZ1HB681K AB 680 p F,50V
C934 VCEAPS105AF1H AB 1 µ F,50V,Electrolytic
C935 VCEAPS105AF1H AB 1 µ F,50V,Electrolytic
C936 VCKYTV1HB224K AC 0.22 µ F,50V
C937 VCKYTV1HB224K AC 0.22 µ F,50V
C938 VCKYTV1HB224K AC 0.22 µ F,50V
C939 VCKYTV1HB224K AC 0.22 µ F,50V
C940 VCKYCY1EB105K AB 1 µ F,25V
C941 VCCCCZ1HH331J AA 330 pF (CH),50V
C942 VCCCCZ1HH331J AA 330 pF (CH),50V
C943 VCKYTV1HB473K AA 0.047 µ F,50V
C944 VCKYTV1HB473K AA 0.047 µ F,50V
C946 VCKYCY1HB104K AD 0.1 µ F,50V
C947 VCKYCY1HB104K AD 0.1 µ F,50V
C948 VCKYCY1HB104K AD 0.1 µ F,50V
C949 VCKYCY1HB104K AD 0.1 µ F,50V
C950 VCKYCY1HB104K AD 0.1 µ F,50V
C951 VCKYCY1HB104K AD 0.1 µ F,50V
C952 VCKYCY1HB104K AD 0.1 µ F,50V
C953 VCKYCY1HB104K AD 0.1 µ F,50V
C954 VCKYTV1HB474K AA 0.47 µ F,50V
C955 VCKYTV1HB474K AA 0.47 µ F,50V
C956 VCKYTV1HB473K AA 0.047 µ F,50V
C957 VCKYTV1HB473K AA 0.047 µ F,50V
C958 VCKYTV1HB473K AA 0.047 µ F,50V
C959 VCKYTV1HB473K AA 0.047 µ F,50V
C963 VCCCCZ1HH680J AB 68 pF (CH),50V
C964 VCCCCZ1HH150J AA 15 pF (CH),50V
C965 VCKYCY1HF223Z AA 0.022 µ F,50V
C967 VCKYCZ1CF104Z AB 0.1 µ F,16V
C972 VCKYCY1EB223K AB 0.022 µ F,25V
C973 VCKYCY1EB223K AB 0.022 µ F,25V
C974 VCKYCY1EB223K AB 0.022 µ F,25V
C975 VCKYCY1EB223K AB 0.022 µ F,25V
C976 VCKYCY1EB223K AB 0.022 µ F,25V
C977 VCKYCY1EB223K AB 0.022 µ F,25V

[7] RESISTORS
R102 VRS-CZ1JF330J AA 33 ohm,1/16W
R103 VRS-CZ1JF103J AA 10 kohm,1/16W
R104 VRS-CZ1JF330J AA 33 ohm,1/16W
R105 VRS-CZ1JF151J AA 150 ohm,1/16W
R106 VRS-CZ1JF332J AA 3.3 kohm,1/16W
R107 VRS-CZ1JF103J AA 10 kohm,1/16W
R108 VRS-CZ1JF000J AA 0 ohms,Jumper
R109 VRS-CZ1JF103J AA 10 kohm,1/16W
R111 VRS-CZ1JF512F AA 5.1 kohm,1/16W
R112 VRS-CZ1JF105J AA 1 Mohm,1/16W
R113 VRS-CZ1JF101J AA 100 ohm,1/16W
R114 VRS-CZ1JF332J AA 3.3 kohm,1/16W
R115 VRS-CZ1JF332J AA 3.3 kohm,1/16W
R118 VRS-CZ1JF332J AA 3.3 kohm,1/16W
R119 VRS-CZ1JF332J AA 3.3 kohm,1/16W
R136 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R137 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R138 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R139 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R140 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R141 VRS-CZ1JF220J AA 22 ohm,1/16W
R142 VRS-CZ1JF330J AA 33 ohm,1/16W
R301 VRS-CZ1JF471J AA 470 ohm,1/16W
R304 VRS-CZ1JF473J AA 47 kohm,1/16W
R305 VRS-CZ1JF000J AA 0 ohms,Jumper
R308 VRS-CZ1JF223J AA 22 kohm,1/16W
R309 VRS-CZ1JF223J AA 22 kohm,1/16W
R310 VRS-CZ1JF223J AA 22 kohm,1/16W
R311 VRS-CZ1JF223J AA 22 kohm,1/16W
R313 VRS-CZ1JF273J AA 27 kohm,1/16W
R314 VRS-CZ1JF273J AA 27 kohm,1/16W
R316 VRS-CZ1JF273J AA 27 kohm,1/16W
R317 VRS-CZ1JF273J AA 27 kohm,1/16W
R318 VRS-CZ1JF000J AA 0 ohms,Jumper
R320 VRS-CZ1JF000J AA 0 ohms,Jumper
R322 VRS-CZ1JF102J AA 1 kohm,1/16W
R323 VRS-CZ1JF000J AA 0 ohms,Jumper
R324 VRS-CZ1JF000J AA 0 ohms,Jumper
R325 VRS-CZ1JF4R7J AA 4.7 ohm,1/16W
R326 VRS-CZ1JF220J AA 22 ohm,1/16W
R327 VRS-CZ1JF101J AA 100 ohm,1/16W
R328 VRS-CZ1JF123J AA 12 kohm,1/16W
R329 VRS-CZ1JF330J AA 33 ohm,1/16W
R330 VRS-CZ1JF102J AA 1 kohm,1/16W
R331 VRS-CZ1JF330J AA 33 ohm,1/16W
R332 VRS-CZ1JF330J AA 33 ohm,1/16W
R333 VRS-CZ1JF330J AA 33 ohm,1/16W

4
HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[7] RESISTORS
R334 VRS-CZ1JF152J AA 1.5 kohm,1/16W
R335 VRS-CZ1JF102J AA 1 kohm,1/16W
R336 VRS-CZ1JF123J AA 12 kohm,1/16W
R337 VRS-CZ1JF123J AA 12 kohm,1/16W
R341 VRS-CZ1JF472J AA 4.7 kohm,1/16W
R342 VRS-CZ1JF562J AA 5.6 kohm,1/16W
R343 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R344 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R345 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R348 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R349 VRS-CZ1JF151J AA 150 ohm,1/16W
R350 VRS-CZ1JF330J AA 33 ohm,1/16W
R352 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R353 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R354 VRS-CZ1JF000J AA 0 ohms,Jumper
R355 VRS-CZ1JF000J AA 0 ohms,Jumper
R356 VRS-CZ1JF000J AA 0 ohms,Jumper
R357 VRS-CZ1JF473J AA 47 kohm,1/16W
R358 VRS-CZ1JF473J AA 47 kohm,1/16W
R363 VRS-CZ1JF000J AA 0 ohms,Jumper
R364 VRS-CZ1JF102J AA 1 kohm,1/16W
R366 VRS-CZ1JF102J AA 1 kohm,1/16W
R367 VRS-CZ1JF102J AA 1 kohm,1/16W
R500 VRS-CZ1JF822J AA 8.2 kohm,1/16W
R501 VRS-CZ1JF103J AA 10 kohm,1/16W
R502 VRS-CZ1JF473J AA 47 kohm,1/16W
R503 VRS-CZ1JF104J AA 100 kohm,1/16W
R504 VRS-CZ1JF104J AA 100 kohm,1/16W
R505 VRS-CZ1JF000J AA 0 ohms,Jumper
R507 VRS-CZ1JF563J AA 56 kohm,1/16W
R508 VRS-CZ1JF563J AA 56 kohm,1/16W
R509 VRS-CZ1JF102J AA 1 kohm,1/16W
R510 VRS-CZ1JF102J AA 1 kohm,1/16W
R511 VRS-CZ1JF102J AA 1 kohm,1/16W
R512 VRS-CZ1JF102J AA 1 kohm,1/16W
R513 VRS-CZ1JF102J AA 1 kohm,1/16W
R514 VRS-CZ1JF102J AA 1 kohm,1/16W
R515 VRS-CZ1JF102J AA 1 kohm,1/16W
R516 VRS-CZ1JF102J AA 1 kohm,1/16W
R518 VRS-CZ1JF102J AA 1 kohm,1/16W
R519 VRS-CZ1JF102J AA 1 kohm,1/16W
R520 VRS-CZ1JF102J AA 1 kohm,1/16W
R521 VRS-CZ1JF102J AA 1 kohm,1/16W
R522 VRS-CZ1JF102J AA 1 kohm,1/16W
R523 VRS-CZ1JF102J AA 1 kohm,1/16W
R526 VRS-CZ1JF474J AA 470 kohm,1/16W
R528 VRS-CZ1JF102J AA 1 kohm,1/16W
R529 VRS-CZ1JF000J AA 0 ohms,Jumper
R530 VRS-CZ1JF102J AA 1 kohm,1/16W
R531 VRS-CZ1JF103J AA 10 kohm,1/16W
R532 VRS-CZ1JF102J AA 1 kohm,1/16W
R533 VRS-CZ1JF102J AA 1 kohm,1/16W
R534 VRS-CZ1JF102J AA 1 kohm,1/16W
R535 VRS-CZ1JF102J AA 1 kohm,1/16W
R539 VRS-CZ1JF330J AA 33 ohm,1/16W
R540 VRS-CZ1JF330J AA 33 ohm,1/16W
R541 VRS-CZ1JF222J AA 2.2 kohm,1/16W
R542 VRS-CZ1JF222J AA 2.2 kohm,1/16W
R543 VRS-CZ1JF102J AA 1 kohm,1/16W
R544 VRS-CZ1JF102J AA 1 kohm,1/16W
R545 VRS-CZ1JF102J AA 1 kohm,1/16W
R546 VRS-CZ1JF103J AA 10 kohm,1/16W
R547 VRS-CZ1JF103J AA 10 kohm,1/16W
R548 VRS-CZ1JF102J AA 1 kohm,1/16W
R549 VRS-CZ1JF102J AA 1 kohm,1/16W
R550 VRS-CZ1JF101J AA 100 ohm,1/16W
R551 VRS-CZ1JF330J AA 33 ohm,1/16W
R552 VRS-CZ1JF330J AA 33 ohm,1/16W
R553 VRS-CZ1JF102J AA 1 kohm,1/16W
R554 VRS-CZ1JF102J AA 1 kohm,1/16W
R555 VRS-CZ1JF102J AA 1 kohm,1/16W
R556 VRS-CZ1JF391J AA 390 ohm,1/16W
R557 VRS-CZ1JF473J AA 47 kohm,1/16W
R558 VRS-CZ1JF473J AA 47 kohm,1/16W
R559 VRS-CZ1JF104J AA 100 kohm,1/16W
R560 VRS-CZ1JF473J AA 47 kohm,1/16W
R561 VRS-CZ1JF473J AA 47 kohm,1/16W
R562 VRS-CZ1JF681J AA 680 ohm,1/16W
R563 VRS-CZ1JF222J AA 2.2 kohm,1/16W
R564 VRS-CZ1JF222J AA 2.2 kohm,1/16W
R565 VRS-CZ1JF223J AA 22 kohm,1/16W
R566 VRS-CZ1JF151J AA 150 ohm,1/16W
R567 VRS-CZ1JF151J AA 150 ohm,1/16W
R570 VRS-CZ1JF102J AA 1 kohm,1/16W
R571 VRS-CZ1JF103J AA 10 kohm,1/16W
R572 VRS-CZ1JF102J AA 1 kohm,1/16W
R573 VRS-CZ1JF103J AA 10 kohm,1/16W
R700 VRS-CZ1JF271J AA 270 ohm,1/16W

5
 HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[7] RESISTORS
R701 VRS-CZ1JF271J AA 270 ohm,1/16W
R702 VRS-CZ1JF271J AA 270 ohm,1/16W
R703 VRS-CZ1JF000J AA 0 ohms,Jumper
R704 VRS-CZ1JF000J AA 0 ohms,Jumper
R705 VRS-CZ1JF271J AA 270 ohm,1/16W
R706 VRS-CZ1JF271J AA 270 ohm,1/16W
R707 VRS-CZ1JF271J AA 270 ohm,1/16W
R708 VRS-CZ1JF271J AA 270 ohm,1/16W
R709 VRS-CZ1JF271J AA 270 ohm,1/16W
R710 VRS-CZ1JF271J AA 270 ohm,1/16W
R711 VRS-CZ1JF271J AA 270 ohm,1/16W
R712 VRS-CZ1JF271J AA 270 ohm,1/16W
R713 VRS-CZ1JF271J AA 270 ohm,1/16W
R714 VRS-CZ1JF271J AA 270 ohm,1/16W
R715 VRS-CZ1JF271J AA 270 ohm,1/16W
R716 VRS-CZ1JF121J AA 120 ohm,1/16W
R717 VRS-CZ1JF121J AA 120 ohm,1/16W
R718 VRS-CZ1JF121J AA 120 ohm,1/16W
R719 VRS-CZ1JF121J AA 120 ohm,1/16W
R720 VRS-CZ1JF121J AA 120 ohm,1/16W
R721 VRS-CZ1JF121J AA 120 ohm,1/16W
R722 VRS-CZ1JF121J AA 120 ohm,1/16W
R723 VRS-CZ1JF121J AA 120 ohm,1/16W
R724 VRS-CZ1JF820J AA 82 ohm,1/16W
R725 VRS-CZ1JF221J AA 220 ohm,1/16W
R727 VRS-CZ1JF182J AA 1.8 kohm,1/16W
R728 VRS-CZ1JF222J AA 2.2 kohm,1/16W
R729 VRS-CZ1JF332J AA 3.3 kohm,1/16W
R730 VRS-CZ1JF393J AA 39 kohm,1/16W
R731 VRS-CZ1JF123J AA 12 kohm,1/16W
R732 VRS-CZ1JF103J AA 10 kohm,1/16W
R734 VRS-CZ1JF471J AA 470 ohm,1/16W
R737 VRS-CZ1JF221J AA 220 ohm,1/16W
R742 VRS-CZ1JF000J AA 0 ohms,Jumper
R805 VRS-CZ1JF000J AA 0 ohms,Jumper
R806 VRS-CZ1JF000J AA 0 ohms,Jumper
R811 VRS-CZ1JF000J AA 0 ohms,Jumper
R813 VRS-CZ1JF103J AA 10 kohm,1/16W
R816 VRS-CZ1JF000J AA 0 ohms,Jumper
R817 VRS-CZ1JF000J AA 0 ohms,Jumper
R818 VRS-CZ1JB103D AB 10 kohm,1/16W
R819 VRS-CZ1JF153J AA 15 kohm,1/16W
R820 VRS-CZ1JF103J AA 10 kohm,1/16W
R821 VRS-CZ1JF104J AA 100 kohm,1/16W
R822 VRS-CZ1JF103J AA 10 kohm,1/16W
R823 VRS-CZ1JF103J AA 10 kohm,1/16W
R824 VRS-CZ1JF103J AA 10 kohm,1/16W
R825 VRS-CZ1JF000J AA 0 ohms,Jumper
R826 VRS-CZ1JF000J AA 0 ohms,Jumper
R828 VRS-CZ1JF104J AA 100 kohm,1/16W
R829 VRS-CZ1JF822J AA 8.2 kohm,1/16W
R830 VRS-CZ1JF433J AA 43 kohm,1/16W
R831 VRS-CZ1JF122J AA 1.2 kohm,1/16W
R834 VRS-CZ1JF103J AA 10 kohm,1/16W
R835 VRS-CZ1JF103J AA 10 kohm,1/16W
R836 VRS-CZ1JF103J AA 10 kohm,1/16W
R837 VRS-CZ1JF101J AA 100 ohm,1/16W
R838 VRS-CZ1JF000J AA 0 ohms,Jumper
R839 VRS-CZ1JF000J AA 0 ohms,Jumper
R840 VRS-CZ1JF000J AA 0 ohms,Jumper
R841 VRS-CZ1JF000J AA 0 ohms,Jumper
R842 VRS-CZ1JF000J AA 0 ohms,Jumper
R844 VRS-CZ1JF000J AA 0 ohms,Jumper
R845 VRS-CZ1JF000J AA 0 ohms,Jumper
R846 VRS-CZ1JB2R2J AB 2.2 ohm,1/16W
R847 VRS-CZ1JF392J AA 3.9 kohm,1/16W
R848 VRS-CZ1JF392J AA 3.9 kohm,1/16W
R849 VRS-CZ1JF392J AA 3.9 kohm,1/16W
R850 VRS-CZ1JF392J AA 3.9 kohm,1/16W
R851 VRS-CZ1JF182J AA 1.8 kohm,1/16W
R903 VRS-TQ2EF000J AA 0 ohms,Jumper
R904 VRS-CZ1JF222J AA 2.2 kohm,1/16W
R905 VRS-CZ1JF103J AA 10 kohm,1/16W
R906 VRS-CZ1JF103J AA 10 kohm,1/16W
R907 VRS-CZ1JF3R3J AA 3.3 ohm,1/16W
R908 VRS-CZ1JF000J AA 0 ohms,Jumper
R909 VRS-CZ1JF151J AA 150 ohm,1/16W
R910 VRS-CZ1JF330J AA 33 ohm,1/16W
R911 VRS-CZ1JF000J AA 0 ohms,Jumper
R912 VRS-CZ1JF102J AA 1 kohm,1/16W
R913 VRS-CZ1JF102J AA 1 kohm,1/16W
R914 VRS-CZ1JF101J AA 100 ohm,1/16W
R915 VRS-CZ1JF101J AA 100 ohm,1/16W
R916 VRS-CZ1JF3R3J AA 3.3 ohm,1/16W
R917 VRS-TQ2EF100J AA 10 ohm,1/8W
R918 VRS-TQ2EF3R3J AA 3.3 ohm,1/8W
R919 VRS-TQ2EF3R3J AA 3.3 ohm,1/8W
R920 VRS-CZ1JF000J AA 0 ohms,Jumper
R921 VRS-CZ1JF000J AA 0 ohms,Jumper
6
 HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[7] RESISTORS
R922 VRS-TQ2EF220J AA 22 ohm,1/8W
R923 VRS-TQ2EF220J AA 22 ohm,1/8W
R924 VRS-TQ2EF6R2J AA 6.2 ohm,1/8W
R925 VRS-TQ2EF6R2J AA 6.2 ohm,1/8W
R926 VRS-TQ2EF6R2J AA 6.2 ohm,1/8W
R927 VRS-TQ2EF6R2J AA 6.2 ohm,1/8W
R928 VRS-CZ1JF000J AA 0 ohms,Jumper
R929 VRS-CZ1JF000J AA 0 ohms,Jumper
R936 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R937 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R938 VRS-CY1JF000J AA 0 ohms,Jumper,0.8X1.55mm,Green
R939 VRS-CY1JB220J AA 22 ohm,1/16W

[8] OTHER CIRCUITRY PARTS

Bi303 QCNWNB154AWPZ AF Connector Ass'y, 2 Pin with Bi304
CNP101 QPLGNA238WJZZ AF Connector, 15 Pin
CNP102 QCNCWA059AW09 AG Connector, 9 Pin
CNP103 QPLGN0061CEZZ AG Connector, 11 Pin
CNP301 QPLGNA238WJZZ AF Connector, 15 Pin
CNP302 QCNCWA059AW09 AG Connector, 9 Pin
CNP501 QPLGN0058CEZZ AF Connector, 8 Pin
CNP803 QCNCM010JAWZZ AC Connector, 9 Pin
CNP804 QPLGN0052CEZZ AD Connector, 2 Pin
CNP901 QPLGN0061CEZZ AG Connector, 11 Pin
CNP902 QCNCW010JAWZZ AC Connector, 9 Pin
CNP903 QPLGNA164WJZZ AG Connector, 8 Pin
CNP905 QPLGN0052CEZZ AD Connector, 2 Pin
CNS804 QCNWNB230AWPZ AG Connector Ass'y, 2 Pin
CNW103 QCNWNB197AWPZ AQ Connector Ass'y, 11 Pin
CNW301 QCNWNB196AWPZ AS Connector Ass'y, 15 Pin
FFC102 QCNWNB151AWPZ AC FFC Cable, 9 Pin
JK301 QJAKM0004AWZZ AK Jack, Headphone
JK302 QSOCJA018AWZZ AD Jack, Audio Line In
JK303 QSOCJA016AWZZ AC Jack, Coxial Digital
JK304 QSOCJA011AWZZ AC Jack, Subwoofer Pre Out
! JK800 QJAKCA006AWZZ AK Jack, DC Input
LUG A QLUGP0002AWZZ AB Lug
LUG B QLUGP0002AWZZ AB Lug
LUG302 QLUGHA006WJZZ AD Lug Terminal
LUG501 QLUGHA006WJZZ AD Lug Terminal
LUG801 QLUGHA006WJZZ AD Lug Terminal
LUG901 QLUGHA006WJZZ AD Lug Terminal
LUG902 QLUGHA006WJZZ AD Lug Terminal
RX1 VHLK2013TH2E1 AG Remote Sensor
RXM301 VHPGP1F31RK-1 AL Jack, Digital In
SW701 QSW-KA037WJZZ AD Switch,Key Type [Power On/Standby]
SW702 QSW-KA037WJZZ AD Switch, Key Type [Volume Down]
SW703 QSW-KA037WJZZ AD Switch, Key Type [Volume Up]
SW704 QSW-KA037WJZZ AD Switch, Key Type [Surround]
SW705 QSW-KA037WJZZ AD Switch, Key Type [Function]

7
 HT-SB300
[9] CABINET PARTS

210 606 x 5
201 608 x 4
225

227

218 608 x 2 226

608 x 3 230
B
214 606 x 5
216 217 210
228
234
605 x 4 233 229
202
216 x 2 608 x 4
217
212 218
C PWB-A3
222 215 x 2
605 x 2
605 x 4 602 x 2
209
219
605 x 2 202
219 605 x 4
208 214
605 x 2
PWB-A1 216
D 605 x 2
215 x 2
222
PWB-A2 209
212 231
601 x 2

607 x 2

224
221 220
236
221
232
220
603 x 4
SP1 604 x 2 235
F 213
221
SP3 604 x 2
207 204 x 2
SP4 221
207-1
207-2 604 x 2
205
604 x 2

G 223
211
SP5
603 x 4
SP6
205 SP2

213

203
H

1 2 3 4 5 6

8
 HT-SB300
PRICE NEW PART
NO. PARTS CODE DESCRIPTION
RANK MARK RANK

[9] CABINET PARTS

201 CCAB-A069AW02 BG Back Cabinet Ass'y
202 CDUC-A089AW01 AP Duct Port Ass'y
203 CPNLSA090AW01 BF Front Panel Ass'y
204 GCOVAA216AWSA AL Cover, LED Top , B
205 GCOVAA217AWSA AE Cover, LED Top , C
206 HDECQA499AWSA AL Panel, Decoration
207 JKNBZA257AW01 AE Function Button Ass'y
207-1 GCOVAA215AWSA --- Cover, LED Top , A ( Not Replacement Part )
207-2 JKNBZA257AWSA --- Button, Function ( Not Replacement Part )
208 LCHSMA083AWFW AL Chassis, Main
209 LHLDZA213AWZZ AL Holder, Duct Port
210 LHLDZA214AWSA AF Bracket, Wall Mount
211 LX-WZ7003AWZZ AB Spacer
212 PCUSSA114AWZZ AD Cushion, Duct Port
213 PCUSSA115AWZZ AD Cushion, Front Speaker
214 PCUSSA116AWZZ AB Cushion, Speaker Sealed, A
215 PCUSSA117AWZZ AD Cushion, Support
216 PCUSSA119AWZZ AH Cushion, Speaker Sealed, B
217 PCUSSA120AWZZ AH Cushion, Sealed Speaker, C
218 PCUSSA121AWZZ AH Cushion, Sealed Speaker, D
219 PCUSSA126AWZZ AA Cushion, E
220 PCUSSA128AWZZ AB Cushion, F
221 PCUSSA130AWZZ AB Cushion, H
222 PFILSA002AWZZ AQ Module, T.B.I., A
223 PFLT-A152AWZZ AB Felt
224 QCNWNB131AW01 AW Speaker Wire Ass'y
225 TLABSA067AWZZ AC Label, Safety Mark [ For U.S.A.Only ]
226 TLABZA797AWZZ AB Label, Jack, A
227 TLABZA798AWZZ AB Label, Jack, B
228 TLABZA875AWZZ AB Label, SRS
229 TLABZA896AWZZ AB Label, DTS
230 TSPC-B130AWZZ AC Label, Specification [ For U.S.A. ]
230 TSPC-B183AWZZ AC Label, Specification [ For Mexico ]
231 92LNBAND1318A AA Nylon Band
232 PCUSSA135AWZZ Cushion, J
233 PSHEMA030AWZZ Sheet, Copper, A
234 PSHEMA031AWZZ Sheet, Copper, B
235 RCORF0018AWZZ AG Filter, Clamp
236 RCORFA017AWZZ Core, Clamp
SP 1,2 RSP-ZA303AWZZ AZ Speaker
SP 3~6 RSP-ZA304AWZZ BB Woofer
601 LX-EZ0010AWF7 AB Special Screw
602 LX-JZ0047AWF7 AB Special Screw
603 XEBY726P08000 AA Screw, M2.6 X 8mm
604 XEBY730P08000 AA Screw, M3 X 8mm
605 XEBY830P10000 AB Screw, M3 X 10mm
606 XEBY835P10000 AB Screw, M3.5 X 10mm
607 XJBY730P08000 AA Screw, M3 X 8mm
608 XJBY830P10000 AA Screw, M3 X 10mm
[10] ACCESSORIES / PACKING PARTS
1 CLEGMA004AW01 AQ Spike Leg Ass'y, A ( Length : 30 mm )
2 CLEGMA005AW01 AN Spike Leg Ass'y, B ( Length : 25 mm )
3 LANGKA167AWFW AK Bracket, Wall Mount
4 PCUSSA118AWZZ AD Cushion, Foot
! 5 QACCDA005AWZZ AQ AC Power Supply Cord
6 QCNWGA041AWPZ AQ RCA Cable
! 7 RADPAA061AW01 BG AC/DC Adaptor Ass'y
8 RRMCGA178AWSA AU Remote Control
9 SPAKAA209AWZZ AK Packing Add, Top
10 SPAKAA210AWZZ AK Packing Add, Bottom
11 SPAKCA628AWZZ AQ Packing Case [ For U.S.A. ]
11 SPAKCA629AWZZ AP Packing Case [ For Mexico ]
12 SPAKGA118AWZZ AU Packing Carton [ For U.S.A. ]
12 SPAKGA119AWZZ AU Packing Carton [ For Mexico ]
13 SPAKZA558AWZZ AD Packing Add, Protection
14 SSAKAA011AWZZ AB Polyethylene Bag, Accessories
15 SSAKHA147AWZZ AD Polyethylene Bag, Unit
16 TCAUHA022AWZZ AE Pattern Paper
17 TINSEA283AWZZ AE Operation Manual
18 TINSZA401AWZZ AC Quick Guide [ For U.S.A. Only ]
19 TLABZA149AWSA AA Label, Energy Star
20 TLABZA801AWZZ AF Label, Pop [ For U.S.A. ]
20 TLABZA806AWZZ AA Label, Pop [ For Mexico ]
21 TLABZA935AWZZ AC Label, Logo

[11] P.W.B. ASSEMBLY ( Not Replacement Item )

! PWB-A 92LPWB7412MANS - MAIN (A1) / POWER (A2) / AMPLIFIER (A3)

9
 HT-SB300
[10] ACCESSORIES / PACKING PARTS

PACKING METHOD (FOR U.S.A ONLY)

1. PACK UNIT TO PACKING CASE

Packing Add., Unit,

Top
SPAKAA209AWZZ

MAIN UNIT

Label, Energy Star

TLABZA149AWSA
Label, Logo
TLABZA935AWZZ Polyethylene Bag, Unit
SSAKHA147AWZZ
Label, Pop
TLABZA801AWZZ

Packing Add., Unit,

AC Power Supply Cord
Bottom
Remote Control
SPAKAA210AWZZ
Operation Manual
Quick Guide
Pattern Paper
RCA Cable
Spike Leg Ass’y A
Spike Leg Ass’y B
Foot Cushion
Wall Mount Bracket
Packing Add, Protection
Polyethylene Bag,
Polyethylene Bag, Accessories
Wall Mount SSAKAA011AWZZ

AC/DC Adaptor Ass’y

Packing Case
SPAKCA628AWZZ

Front Of Packing Case

2. PACK PACKING CASE TO CARTON

Packing Case

Carton
SPAKGA118AWZZ

Not Replacement Item

10
HT-SB300

11
 HT-SB300
-MEMO-
HT-SB300

COPYRIGHT 2009 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without
prior written permission of the publisher.

SHARP CORPORATION
S&O Electronics (Malaysia) Sdn. Bhd.
Sungai Petani, Kedah,
Malaysia

Printed in Malaysia
A0902-1MX•RR•M
SC•MX