Scribd Logo
Upload

Welcome to Scribd!

  • 17 views

    SC-I 020.10.22 Control Points After Dismantling For Indiction Machine Ver B

    Uploaded by

    Rafeek Ali
    This document provides a summary of control points to check after dismantling, cleaning, and drying an induction machine. It lists 16 components and their associated control points, including checking the stator and rotor windings, frames, laminations, shafts, bearings, and lubrication parts for cleanliness, wear, dimensions, and other defects. Visual inspections and comparisons to specification documents are specified for evaluating the control points.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    SC-I 020.10.22 Control Points After Dismantling For Indiction Machine Ver B

    Uploaded by

    Rafeek Ali
    17 views5 pages
    This document provides a summary of control points to check after dismantling, cleaning, and drying an induction machine. It lists 16 components and their associated control points, including checking the stator and rotor windings, frames, laminations, shafts, bearings, and lubrication parts for cleanliness, wear, dimensions, and other defects. Visual inspections and comparisons to specification documents are specified for evaluating the control points.

    Original Title

    SC-I_020.10.22_Control_points_after_dismantling_for_indiction_machine_ver_B

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a summary of control points to check after dismantling, cleaning, and drying an induction machine. It lists 16 components and their associated control points, including checking the stator and rotor windings, frames, laminations, shafts, bearings, and lubrication parts for cleanliness, wear, dimensions, and other defects. Visual inspections and comparisons to specification documents are specified for evaluating the control points.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    17 views5 pages

    SC-I 020.10.22 Control Points After Dismantling For Indiction Machine Ver B

    Uploaded by

    Rafeek Ali
    This document provides a summary of control points to check after dismantling, cleaning, and drying an induction machine. It lists 16 components and their associated control points, including checking the stator and rotor windings, frames, laminations, shafts, bearings, and lubrication parts for cleanliness, wear, dimensions, and other defects. Visual inspections and comparisons to specification documents are specified for evaluating the control points.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    Document kind Document identity Revision

    Service instruction SC-I 020.10.22 B


    Owner organization Document type Date of revision (yyyy-mm-dd) Status Page(s)

    Motors & Generators Control points after dismantling, 2013-10-18 Valid 1(5)
    cleaning and drying for induction
    machines
    Division/Department Prepared by Approved by Security level

    PG Service Bengt Stehagen PO Johansson Internal limited

    Control phase
    Control after dismantling, cleaning and drying

    No. Component / Control point Point Control of Document


    Stator:
    1 Winding a Cleanliness Visual
    b Insulation coverage inspection
    c Staggering
    d Soldering sleeves
    e Loose wedges

    2 Insulation testing
    Insulation resistance a Stator winding to earth and SC-I 020.10.52
    between phases
    Resistance element
    Heater
    3 Voltage test b Electrical strength SC-I 020.10.58

    4 Frame a Cleanliness Visual


    b Bolts inspection
    c Feet
    d Dowel pins, steering edges
    e Lifting eyes
    f Welds

    5 Lamination a Scrape marks Visual


    b Pressure fingers inspection
    c Clean cooling channels
    d Lamination burns

    We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without
    express authority is strictly forbidden.
    Copyright 2011 ABB.
    Document kind Document identity Revision

    Service instruction SC-I 020.10.22 B


    Owner organization Document type Date of revision (yyyy-mm-dd) Status Page(s)

    Motors & Generators Control points after dismantling, 2013-10-18 Valid 2(5)
    cleaning and drying for induction
    machines
    Division/Department Prepared by Approved by Security level

    PG Service Bengt Stehagen PO Johansson Internal limited

    No. Component / Control point Point Control of Document


    Rotor:
    6 Winding with short circuit a Faulty connections Visual
    rings b Cracks inspection
    c Insulation
    d Wedges

    7 Lamination a Scrape marks Visual


    b Clean cooling channels inspection
    c Pressure fingers
    d Fastening to hub

    8 Hub a Fastening Visual


    b Locking inspection
    c Welds

    9 Balancing disc a Fastening Visual


    b Locking inspection

    10 Fans a Welds Visual


    b Fan blade inspection
    c Fastening
    d Locking
    c Fit

    We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without
    express authority is strictly forbidden.
    Copyright 2011 ABB.
    Document kind Document identity Revision

    Service instruction SC-I 020.10.22 B


    Owner organization Document type Date of revision (yyyy-mm-dd) Status Page(s)

    Motors & Generators Control points after dismantling, 2013-10-18 Valid 3(5)
    cleaning and drying for induction
    machines
    Division/Department Prepared by Approved by Security level

    PG Service Bengt Stehagen PO Johansson Internal limited

    No. Component / Control point Point Control of Document


    11 Shaft(s) a Fit Visual
    b Surface finish inspection
    c Key slot
    d Key
    e Dimensions SC-I 020.10.67
    f Tolerances

    12 Bearing housing a Dimensions SC-I 020.10.67


    b Tolerances

    13 Balancing a Residual unbalance SC-I 020.10.62

    Anti friction bearing:


    14 Ball bearings/ a Bearing number Note on work
    Roller bearings b Play order
    c Discoloration/wear SKF bearing
    d Fitting corrosion failure

    Sleeve bearing: a Cleanliness Visual


    15 Top half b Wear inspection
    Bottom half c Loose inserts
    d Dimension SC-I 020.10.67
    e Tolerances

    16 Lubrication rings a Wear Visual


    inspection
    Lubrication disc b Out of roundness

    We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without
    express authority is strictly forbidden.
    Copyright 2011 ABB.
    Document kind Document identity Revision

    Service instruction SC-I 020.10.22 B


    Owner organization Document type Date of revision (yyyy-mm-dd) Status Page(s)

    Motors & Generators Control points after dismantling, 2013-10-18 Valid 4(5)
    cleaning and drying for induction
    machines
    Division/Department Prepared by Approved by Security level

    PG Service Bengt Stehagen PO Johansson Internal limited

    No. Component / Control point Point Control of Document


    17 Bearing assembly: Cracks Visual
    Inner bearing cap a Cleanliness inspection
    Outer bearing cap b Wear
    Labyrinths c Machined bearing caps
    for anti-friction bearings
    Valve disc d Grease channels
    Grease screen e Seal surfaces
    Other bearing assembly f
    details

    18 Bearing shields a Cracks Visual


    Bearing stands b Cleanliness inspection

    19 End shields a Clean grease channels Visual


    b Clean oil houses inspection
    c Oil level pipes, air pipes
    d Grease nipples

    20 Bearing seat g Dimension SC-I 020.10.67


    h Tolerances

    Other details:
    21 Mechanical coupling a Cracks Visual
    b Distances inspection
    c Bolts
    d Fittings
    e Key
    f Key slot

    22 Cooler a Cleanliness Visual


    b Seals, gaskets inspection
    c Sacrificial anode
    d Pressure test According to
    name plate for
    cooler

    23 Lubrication a Quantity Note on work


    order

    We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without
    express authority is strictly forbidden.
    Copyright 2011 ABB.
    Document kind Document identity Revision

    Service instruction SC-I 020.10.22 B


    Owner organization Document type Date of revision (yyyy-mm-dd) Status Page(s)

    Motors & Generators Control points after dismantling, 2013-10-18 Valid 5(5)
    cleaning and drying for induction
    machines
    Division/Department Prepared by Approved by Security level

    PG Service Bengt Stehagen PO Johansson Internal limited

    Rev. Date Prepared by Division/ Department Description


    (yyyy-mm-dd)
    A 2012-09-12 BS PG Service First version
    B 2013-10-18 BS PG Service Separated control points and control of, new instruction for
    dimension and tolerances

    We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without
    express authority is strictly forbidden.
    Copyright 2011 ABB.

    You might also like