DS Mold 4140

Industeel
AISI 4140-W1.7225-EN 42CrMo4
4140-1.7225: A prehardened mold steel (260-310 HB)

4140 or 1.7225 are chromium-manganese-molybdenum grade designed for plastic mold
industry. These grades are normally delivered in a prehardened condition at a hardness level
of 260-310 HB. These grade have a fully homogeneous martensite-bainite microstructure.
Toughness, high fatigue are the main characteristics of these family of tool steels.
Industeel is using a typical unique chemical analysis covering both 4140 and 1.7225 chemical specifications
This grade is typically used for:
> Big mechanical parts
> plastic injection molds for thermoplastics
PROPERTIES
CHEMICAL ANALYSIS - WEIGHT%
Analysis in % C Si Mn Ni Cr Mo S P
Min 0.36 0.15 0.75 - 0.80 0.15 - -
4140 Typ 0.41 0.275 0.85 < 0.06 1.05 0.20 <0.004 <0.020
Max 0.44 0.35 1.00 < 0.28 1.10 0.25 <0.005 <0.020
Min 0.38 0.10 0.60 - 0.90 0.15 - -
1.7225
Typ 0.41 0.275 0.85 < 0.06 1.05 0.20 <0.004 <0.100
42 CrMo4
Max 0.45 0.40 0.90 <0.28 1.20 0.30 <0.0035 <0.250
MECHANICAL PROPERTIES
Typical values for plates air quenched and tempered (thickness 45 mm - 1.8”). Density 7.85 g/cm3
Reduction
Hardness YS 0.2 UTS Elongation Chatpy V (20°C)
of area
HB MPa KSI MPa KSI % Z% J Ft.Lbs
Longitudinal 260-
875 127 1050 152 13 40 12 9
direction 310
PHYSICAL PROPERTIES
Thermal conductivity Thermal expansion coefficient
W m-1 K-1 10-6°C-1/10-6°K-1
20°C 20-100°C 20-200°C 20-300°C
68°F 68-212°F 68-392°F 68-572°F
42 11.1 12.1 12.9
1
®
Industeel Trademark - DS-MOLD-4140 09/2022
PROPERTIES
METALLURGICAL PROPERTIES
4140 has an excellent hardenability resulting in good uniformity of hardness and microstructure.
Internal soundness:
All plates are ultrasonically tested according to NFA 04305 Class C.- ASTM A 578-59 2mm flat bottom hole
Grain size:
Uniform 7/8 grain size according to ASTM E112.
Metallurgical transformation points
AC 1 AC3 Ms V1 V2
733 °C 780°C 320°C 1000°C/h 300°C/h
1351°F 1436 °F 608°F 1800°F/h 540°F/h
PLATE PROCESSING
HEAT TREATMENT Tempering curve Test conditions:

For specific applications where mechanical properties Test conditions:
higher than 30 HRC are required, hardening can be > austenitization 870°C (1598°F)
performed in the following way: > tempering/holding time 1h
> heating (about 850°C - 1562°F) with a > air cooling
sufficient holding time (1 hour/inch)
Brinell Hardness (HB) HRC Hardness
> water, oil or air quenching depending on thickness
400 42
(see C.C.T diagram)
350 38
>the tempering temperature controls the
mechanical characteristics (see tempering curve) 300 32
The following instructions must be followed to obtain an 250 22

efficient tempering:
200 14
>Uniform heating at the selected tempering 520°C 560°C 600°C 640°C
968°F 1040°F 1112°F 1184°F
temperature (see tempering curve)
Tempering temperature
> Holding time of one hour per inch of total
thickness Note that complicated shapes require accurate control
> Double tempering with complete cooling to room of steel temperature uniformity and sufficient holding
temperature for each treatment times to limit stresses and prevent cracking.
2
®
PLATE PROCESSING
POLISHING
4140 -1.7225 can be roughly polished in the quenched and tempered condition. After grinding, polishing will be
made with aluminium oxide or diamond paste.
MICRO CLEANLINESS
Typical A (Sulfide) : 2,5 ; B (Aluminatess) : 0, ; C (Silicates) : 0 ; D ( Globular oxydes ) :1
WELDING
Welding of 4140 - 1.7225 requires special care . High pre/post-heating temperature should be used (350°C –
660°F) to avoid cold cracking.
DELIVERY CONDITIONS
DIMENSIONAL PROGRAM
Thickness Width
20 - 120 mm 1500 - 2500 mm
(. 79’’ - 4.7’’) (59 - 98.4’’)
120 - 500 mm 2000 mm
(4.7’’ - 20’’) (82.7’’)
YOUR CONTACTS
Perrine Lavalley Industeel France
Tel. +33 3 85 80 52 56 Le Creusot Plant
[email protected] 56 rue Clemenceau
F - 71201 Le Creusot Cedex
https://industeel.arcelormittal.com
Technical data and information are to the best of our knowledge at the time of printing. However, they may be subject to some slight variations due to our ongoing
research programme on steels.Therefore, we suggest that information be verified at time of enquiry or order.Furthermore, in service, real conditions are specific for
each application. The data presented here are only for the purpose of description, and considered as guarantees when written formal approval has been delivered by our
company.Further information may be obtained from the address opposite.
3
®

DS Mold 4140

Uploaded by

Copyright:

Available Formats

DS Mold 4140

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DS Mold 4140

Uploaded by

Copyright:

Available Formats

Industeel

AISI 4140-W1.7225-EN 42CrMo4

4140-1.7225: A prehardened mold steel (260-310 HB)

HEAT TREATMENT Tempering curve Test conditions:

The following instructions must be followed to obtain an 250 22

You might also like