DESIGNED BY DATE PROJECT:

Engineering and Development MBS 1/15/2024 GLOBE - 884M

Corporation of the Philippines CHECKED BY DATE SHEET NO.

A. MAIN POLE

FIGURES
GIVEN DATA:
Applied Axial Load, PA = 195.997 kN from Staad
Diameter of Base Plate, DB = 1630 mm
Thickness of Base Plate, TB = 65 mm
Diameter of Steel Pipe, DP = 1348 mm
Stiffener Height, H = 300 mm
Base Length of Stiffener, L = 140 mm
Thickness of Stiffener, t = 20 mm
Length of Cantilever Connection, CL = 141 mm (DB/2 - Dp/2 - L)
Length of Simply Supported Connection, Ls = 264.7 mm (R*Interior Angle)
Yield Stress of Steel, fy = 248 MPa
A1 = 2086724 mm2
A2 = 3300636 mm2
Compressive strength of concrete, fc = 21.00 Mpa
BEARING CAPACITY
Allowable Bearing Stress of Concrete
Fp = 0.85 f'c - on full area of a concrete support
Fp = 0.85 f'c * (A2/A1)^(1/2) ≤ 1.7f'c - on less than the full area of a concrete support
where; A1 = Area of Steel concentrically bearing on concrete support
A2 = Maximum area of the portion of the supporting surface that
is geometrically similar to and concentric with the loaded area
Fp = 22.449

Actual Bearing Stress:

fa = Axial Load/Area of Base Plate
Area of Base Plate, Ab = 2086724 mm2
fa = 0.09 MPa SAFE!!!!
Determine the Actual Bending Moment
Consider 1 mm strip
For Cantilever Section:
Uniform load, W Moment = WL2/2
W = fa* 1mm SAFE!!!! = 933.67 N-mm
W = 0.09 N/mm
Determine the required thickness, t
= (6 M/0.9fy)^0.5
t = 5.01 mm OK!!!!
 DESIGNED BY DATE PROJECT:

Engineering and Development MBS 1/15/2024 GLOBE - 884M

Corporation of the Philippines CHECKED BY DATE SHEET NO.

For Simply Supported Section:

P

ts

300 mm
H

65 mm

` 265 mm
320 DB
W
TRIBUTARY AREA

265 140 mm

CHECK FOR BENDING

TOP Uniform Load, W
= (Ls top + Ls bot)/2)*fa
W = 27.461 N/mm
Moment = WL2 / 2
= 269113.2 N-mm
Centroid of T- Section

Area (mm2) Centroid Section

from bot. Area * Centroid Centroid of T - Section Modulus, I/c
A1 6000 215 1290000 285 mm Top 698264.4
A2 17204 32.5 559134.769999686 80 mm Bottom 2499966.3
Total 23204.15 1849134.76999969

Moment of Inertia of T- Section

Area Lever arm from IT=I + Ad2 (mm4)
Moment of Inertia, I centroid, d
A1 6000 45000000 135.31 154853034.5
A2 17204 6057293.34 47.19 44368882.8
Total 199221917.29

Check for Flexural Stress

Lc = 200 bf /(fy)^0.5
= 3.3614 m > Lb = 0.14 m Compact Section
allow fb = 0.9fy
= 223.2 Mpa
actual fb = M / Sx
= 0.11 Mpa < allow fb SAFE!!
Check for Shear Stress
Allowable Shear Stress
fv = 0.90fy
= 223.2 MPa
Actual Shear Stress
fv = V / dtw
Shear, V = WL
= 3844.5 N
fv = 0.527 Mpa SAFE!!!
 DESIGNED BY DATE PROJECT:
Engineering and Development MBS 1/15/2024 GLOBE - 884M
Corporation of the Philippines CHECKED BY DATE SHEET NO.
5

A. MAIN POLE

FIGURES
GIVEN DATA:
Applied Axial Load, PA = 0.958 kN from Staad
Length of Base Plate, LB = 250 mm
Width of Base Plate, WB = 250 mm
Thickness of Base Plate, TB = 10 mm
Diameter of Steel Pipe, DP = 114.3 mm
Stiffener Height, H = 105 mm
Base Length of Stiffener, L = 68 mm
Thickness of Stiffener, t = 7 mm
Length of Cantilever Connection, CL = 67.85 mm (DB/2 - Dp/2 - L)
Length of Simply Supported Connection, Ls = 125 mm (R*Interior Angle)
Yield Stress of Steel, fy = 248 MPa
A1 62500 mm2
A2 184900 mm2

BEARING CAPACITY
Allowable Bearing Stress of Concrete
Fp = 0.35 f'c - on full area of a concrete support
Fp = 0.35 f'c * (A2/A1)^(1/2) ≤ 0.7f'c - on less than the full area of a concrete support
where; A1 = Area of Steel concentrically bearing on concrete support
A2 = Maximum area of the portion of the supporting surface that
is geometrically similar to and concentric with the laded area
Fp = 12.642 MPa ≤ 14.7 Mpa OK!!!!

Actual Bearing Stress:

fa = Axial Load/Area of Base Plate
Area of Base Plate, Ab = 62500 mm2
fa = 0.02 MPa SAFE!!!!
Determine the Actual Bending Moment
Consider 1 mm strip
For Cantilever Section:
Uniform load, W Moment = WL2/2
W = fa* 1mm = 35.28 N-mm
W = 0.02 N/mm
Determine the required thickness, t
= (6 M/0.75fy)^0.5
t = 1.07 mm < 10 ok!!!
 DESIGNED BY DATE PROJECT:
Engineering and Development MBS 1/15/2024 GLOBE - 884M
Corporation of the Philippines CHECKED BY DATE SHEET NO.
6

For Simply Supported Section:

P

t
s

105 mm
H
10 mm

` 125 mm
125 DB
W
TRIBUTARY AREA

125 68 mm

CHECK FOR BENDING

TOP Uniform Load, W
= (Ls top + Ls bot)/2)*fa
W = 1.916 N/mm
Moment = WL2 / 2
= 4429.792 N-mm
Centroid of T- Section

Area (mm2) Centroid Area * Centroid Centroid of T - Section Section Modulus,

from bot. I/c
A1 735 62.5 45937.5 89 mm Top 24980.4
A2 1250 5 6250 26 mm Bottom 84287.0
Total 1985 52187.5

Moment of Inertia of T- Section

Lever arm from
Area Moment of Inertia, I centroid, d IT=I + Ad2 (mm4)
A1 735 675281.25 36.21 1638937.3
A2 1250 10416.67 21.29 577046.4
Total 2215983.65

Check for Flexural Stress

Lc = 200 bf /(fy)^0.5
= 1.5875 m > Lb = 0.07 m Compact Section
allow fb = 0.66fy
= 163.68 Mpa
actual fb = M / Sx
= 0.05 Mpa < allow fb SAFE!!
Check for Shear Stress
Allowable Shear Stress
fv = 0.40fy
= 99.2 MPa
Actual Shear Stress
fv = V / dtw
Shear, V = WL
= 130.3 N
fv = 0.162 Mpa SAFE!!!
 DESIGNED BY DATE PROJECT;
Engineering and Development MBS 1/15/2024 GLOBE - 884M
Corporation of the Philippines CHECKED BY DATE SHEET NO.
6

FIGURE: Anchor Rod Detail Types:

ANCHOR RODS:
For anchors rods, the following interaction shall be satisfied:

ANSI/TIA-222-G, Section 4.9.9

where:
Φ = 0.8
Pu = tension force for detail types (a), (b), (c ) and the larger of compression or tension
force for type (d)
Vu = shear force(direct shear and torsion components) corresponding to P u
Rnt = nominal tensile strength of anchor rod as per (TIA 222-G, Section 4.9.6.1)
η = 0.90 for detail type (a)
= 0.70 for detail type (b)
= 0.55 for detail type (c )
= 0.50 for detail type (d)
Design of Tensile Strength
ΦRnt = ΦFub An
where:
An = net area of the threaded portion of the bolt given by
An = (∏/4) (d - 0.9382p)2mm2
or An = 0.75 Ab
where:
Φ = 0.75
Fub = specified minimum tensile strength of bolt
d = nominal diameter of bolt
p = pitch of threads, mm
Ab = nominal unthreaded body area of bolt
Given Data:
d = 16 mm
p = 1.5 mm (Assumed pitch of bolt)
An = 150.80 mm2
Fub = 620 MPa (A325) (NSCP Table 510.3.2)
ΦRnt = 70.12 kN (Design of Tensile Strength)
Applied Load:
Pu = 7.57 kN (maximum tensile force)
Vu = 9.285 kN (maximum shear force)
Interaction Equation:

0.074 < 1.0 [Satisfactory]

EMBEDMENT OF ANCHORED BARS IN COMPRESSION

National Structural Code of the Philippine (NSCP Vol. 6), Section 412.4
Minimum Embedment Lengt = max {12db,200} mm
Ld1 = 200 mm
Ld2 = 192 mm
Use Ld = 200 mm Required Embedment Length
 DESIGNED BY DATE PROJECT:

Engineering and Development MBS 1/15/2024 GLOBE - 884M

Corporation of the Philippines CHECKED BY DATE SHEET NO.

FIGURE :

ANCHOR BOLTS CAPACITY: BOTTOM SUPPORT

GIVEN DATA :
Applied Loads Pshear = 1.104 kN
Ptension = 0.044 kN
Diameter of Bolts: d = 16 mm
Diameter of Hole: d = 18 mm
Effective Area: A = 145.81 mm2
Bearing Area of Head: Ab = 292.90 mm2
Number of Bolts : n = 4 pcs

Using A325 Bolts

Steel Strength of Anchor in Shear

From Table 510.3.2, National Structural Code of the Philippine (NSCP Vol. 6)

Allowable Shear Stress: Fv = 330 MPa

Computed Shear Stress:

fv = Pshear / Av

fv = 1.893 MPa SAFE

Steel Strength of Anchor in Tension:

From Table 510.3.2, National Structural Code of the Philippine (NSCP Vol. 6)

Allowable Tensile Stress: Fu = 620 MPa

Computed Tensile Stress:

fv = Ptension / As

fv = 0.075 MPa SAFE

 DESIGNED BY DATE PROJECT:
Engineering and Development MBS 1/15/2024 GLOBE - 884M
Corporation of the Philippines CHECKED BY DATE SHEET NO.

FIGURE :

CONCRETE PROPERTIES

Concrete Properties: fc' = 21 MPa

Yield Strength: fy = 414 MPa
Concrete Thickness : t = 170 mm
Steel Reduction Factor in Tension
f = 0.75

CHECKING OF PULLOUT IN CONCRETE

GIVEN DATA :

Applied Loads Px = 0.044 kN (Ultimate Factored Tensile Load)

Pullout Strength
fN = f Ψ (Ab 8fc') (English)
y term is 1.0 for location where concrete cracking is likely to occur.

fN = 8.30 kips The pullout strength in tension of a single headed stud or bolt

fN = 36.91 kN SAFE

EMBEDMENT OF ANCHORED BARS IN TENSION

National Structural Code of the Philippine (NSCP Vol. 6), Section 412.7.2

Minimum Embedment Length

= max {12db,150}
Ld1 = 150 mm
Ld2 = 192 mm

Use Ld = 192 mm Required Embedment Length

 DESIGNED BY DATE PROJECT:

Engineering and Development MBS 1/15/2024 GLOBE - 884M

Corporation of the Philippines CHECKED BY DATE SHEET NO.

FIGURE :

ANCHOR BOLTS CAPACITY: TOP SUPPORT

GIVEN DATA :
Applied Loads Pshear = 2.202 kN
Ptension = 3.149 kN
Diameter of Bolts: d = 16 mm
Diameter of Hole: d = 18 mm
Effective Area: A = 145.81 mm2
Bearing Area of Head: Ab = 292.90 mm2
Number of Bolts : n = 4 pcs

Using A325 Bolts

Steel Strength of Anchor in Shear

From Table 510.3.2, National Structural Code of the Philippine (NSCP Vol. 6)

Allowable Shear Stress: Fv = 330 MPa

Computed Shear Stress:

fv = Pshear / Av

fv = 3.776 MPa SAFE

Steel Strength of Anchor in Tension:

From Table 510.3.2, National Structural Code of the Philippine (NSCP Vol. 6)

Allowable Tensile Stress: Fu = 620 MPa

Computed Tensile Stress:

fv = Ptension / As

fv = 5.399 MPa SAFE

 DESIGNED BY DATE PROJECT:

Engineering and Development MBS 1/15/2024 GLOBE - 884M

Corporation of the Philippines CHECKED BY DATE SHEET NO.

FIGURE :

CONCRETE PROPERTIES

Concrete Properties: fc' = 21 MPa

Yield Strength: fy = 414 MPa
Concrete Thickness : t = 170 mm
Steel Reduction Factor in Tension
f = 0.75

CHECKING OF PULLOUT IN CONCRETE

GIVEN DATA :

Applied Loads Px = 3.149 kN (Ultimate Factored Tensile Load)

Pullout Strength
fN = f Ψ (Ab 8fc') (English)
y term is 1.0 for location where concrete cracking is likely to occur.

fN = 8.30 kips The pullout strength in tension of a single headed stud or bolt

fN = 36.91 kN SAFE

EMBEDMENT OF ANCHORED BARS IN TENSION

National Structural Code of the Philippine (NSCP Vol. 6), Section 412.7.2

Minimum Embedment Length

= max {12db,150}
Ld1 = 150 mm
Ld2 = 192 mm

Use Ld = 192 mm Required Embedment Length