Torque Specs

5/13/2018 Fastener Tightening Specifications - Engine • 2008 Pontiac G6 • MotoLogic
2008 G6
Applies to:
Report a problem with this article
3.5L
Fastener Tightening Specifications

Specification
Application Metric English
A/C Compressor Bracket Bolt 50 Y 37 lb ft
Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft
Camshaft Position Actuator Magnet Bolt 10 Y 89 lb in
Camshaft Position Sensor Bolt 10 Y 89 lb in
Camshaft Thrust Plate Screw 10 Y 89 lb in
Clutch Pressure Plate Bolt 25 Y 18 lb ft
Connecting Rod Bearing Cap Bolt
First Pass 25 Y 18 lb ft
Final Pass 110 degrees
Coolant Crossover Pipe Bolt – Front 50 Y 37 lb ft
Coolant Crossover Pipe Bolt – Side 10 Y 89 lb in
Coolant Drain Plug 19 Y 14 lb ft
Coolant Temperature Sensor 23 Y 17 lb ft
Crankshaft Balancer Bolt
Installation Pass Using the Old Bolt to Ensure the 125 Y 92 lb ft

Balancer is Completely Installed
First Pass – Install a NEW Bolt After the

Installation Pass and Tighten as Described in the 125 Y 92 lb ft
First and Final Passes
Crankshaft Main Bearing Cap Bolt/Stud
https://www.motologic.com/car/82599d10-a822-012a-9d60-f67652ef7803/article/d6ab9fc03ba149cdec598cff8a2342c3?returnPath=%2Fcar%2F82599d10-a822-012a-
Specification
Crankshaft Oil Deflector Nut 25 Y 18 lb ft
Crankshaft Position Sensor Shield Nut 11 Y 98 lb in
Crankshaft Position Sensor Stud 11 Y 98 lb in
Cylinder Head Bolt
Drive Belt Idler Pulley Bolt – 13 mm 30 Y 22 lb ft
Drive Belt Idler Pulley Bolt – 15 mm 50 Y 37 lb ft
Drive Belt Idler Pulley Bolt
Upper Right and Lower Left 50 Y 37 lb ft
Center Right 30 Y 22 lb ft
Drive Belt Tensioner Bolt 50 Y 37 lb ft
Engine Block Heater 50 Y 37 lb ft
Engine Block Plug 60 Y 44 lb ft
Engine Front Cover Bolt 25 Y 18 lb ft
Engine Lift Bracket Bolt 70 Y 52 lb ft
Engine Mount Bolts 50 Y 37 lb ft
Engine Mount Bracket Bolts
Convertible 50 Y 37 lb ft
Except Convertible
Bracket to Engine Block 90 Y 66 lb ft
Specification
Bracket to Oil Pan 50 Y 37 lb ft
Engine Mount Bracket Lower Bolts 50 Y 37 lb ft
Engine Mount Bracket Upper Bolts 90 Y 66 lb ft
Engine Mount Nuts 50 Y 37 lb ft
Engine Mount Strut Bolts 50 Y 37 lb ft
Engine Mount Strut Bracket to Engine Bolts 25 Y 18 lb ft
Engine Oil Pressure Switch 16 Y 12 lb ft
Engine Wiring Harness Bracket Bolt 13 Y 115 lb in
Engine Wiring Harness Ground Terminal Nut 25 Y 18 lb ft
EVAP Purge Valve Bolt 12 Y 106 lb in
Exhaust Crossover Heat Shield Bolts 10 Y 89 lb in
Exhaust Crossover Pipe Nuts 25 Y 18 lb ft
Exhaust Crossover Pipe Studs 25 Y 18 lb ft
Exhaust Manifold Bolt 20 Y 15 lb ft
Exhaust Manifold Heat Shield Bolt 10 Y 89 lb in
Exhaust Manifold Lower Heat Shield Bolt 10 Y 89 lb in
Flywheel Bolt
Automatic Transmission 70 Y 52 lb ft
Manual Transmission – First Pass 50 Y 37 lb ft
Manual Transmission – Final Pass 70 degrees
Front Oil Gallery Plug 33 Y 24 lb ft
Fuel Injector Rail Bolt 10 Y 89 lb in
Fuel Injector Wiring Harness Electrical Connector Bracket

14 Y 124 lb in
Bolt
Generator Rear Brace Upper Nut 25 Y 18 lb ft
Specification
Generator Through Bolt 50 Y 37 lb ft
Heated Oxygen Sensor 42 Y 31 lb ft
Heater Inlet and Outlet Pipe Bolt – 10 mm 10 Y 89 lb in
Heater Inlet and Outlet Pipe Bolt/Nut – 13 mm 25 Y 18 lb ft
Heater Inlet Pipe Stud 35 Y 26 lb ft
Ignition Coil Bracket Bolt/Nut/Stud 25 Y 18 lb ft
Intake Manifold Cover Ball Stud 10 Y 89 lb in
Knock Sensor 25 Y 18 lb ft
Lower Intake Manifold Bolt – Center
First Pass 7Y 62 lb in
Final Pass 16 Y 12 lb ft
Lower Intake Manifold Bolt – Corner
First Pass 7Y 62 lb in
Final Pass 25 Y 18 lb ft
Oil Filter 30 Y 22 lb ft
Oil Filter Adapter Bolt 25 Y 18 lb ft
Oil Filter Adapter Heat Shield Nuts 25 Y 18 lb ft
Oil Filter Fitting 39 Y 29 lb ft
Oil Level Indicator Tube Bolt 25 Y 18 lb ft
Oil Pan Bolt 25 Y 18 lb ft
Oil Pan Drain Plug 25 Y 18 lb ft
Oil Pan Side Bolt
Specification
Oil Pan Support Bracket Bolt 50 Y 37 lb ft
Oil Pan to Transaxle Bolts 50 Y 37 lb ft
Oil Pump Cover Bolt 10 Y 89 lb in
Oil Pump Drive Gear Clamp Bolt 36 Y 27 lb ft
Oil Pump Mounting Bolt 41 Y 30 lb ft
Piston Oil Nozzle Bolt 10 Y 89 lb in
Rear Oil Gallery Plug – 3/8 inch 33 Y 24 lb ft
Spark Plug 15 Y 11 lb ft
Starter Motor to Engine Block Bolts 40 Y 30 lb ft
Throttle Body Bolt/Nut 10 Y 89 lb in
Throttle Body Stud 6Y 53 lb in
Timing Chain Tensioner Bolt 21 Y 15 lb ft
Torque Converter to Flexplate Bolts 62 Y 46 lb ft
Transaxle Brace Bolts 72 Y 53 lb ft
Transaxle to Engine Bolts 75 Y 55 lb ft
Transaxle to Oil Pan Bolts 50 Y 37 lb ft
Transmission to Engine Bolts 75 Y 55 lb ft
Transmission to Engine Brace Bolts 50 Y 37 lb ft
Transmission Torque Converter Cover Bolts 7.5 Y 66 lb in
Transmission Torque Converter to Flex Plate Bolts 62 Y 46 lb ft
Upper Intake Manifold Bolt/Stud 25 Y 18 lb ft
Valve Lifter Guide Bolt 10 Y 89 lb in
Valve Lifter Oil Manifold Cover Plate Bolt 25 Y 18 lb ft
Valve Rocker Arm Bolt 34 Y 25 lb ft
Valve Rocker Arm Cover Bolt 10 Y 89 lb in
Water Inlet Bolt/Stud 10 Y 89 lb in
Water Pump Bolt 25 Y 18 lb ft
Specification
Water Pump Pulley Bolt 25 Y 18 lb ft

Torque Specs

Uploaded by

Copyright:

Available Formats

Torque Specs

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Torque Specs

Uploaded by

Copyright:

Available Formats

5/13/2018 Fastener Tightening Specifications - Engine • 2008 Pontiac G6 • MotoLogic

Fastener Tightening Specifications

Application Metric English

A/C Compressor Bracket Bolt 50 Y 37 lb ft

Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft

Camshaft Position Actuator Magnet Bolt 10 Y 89 lb in

Camshaft Position Sensor Bolt 10 Y 89 lb in

Camshaft Thrust Plate Screw 10 Y 89 lb in

Clutch Pressure Plate Bolt 25 Y 18 lb ft

Connecting Rod Bearing Cap Bolt

Final Pass 110 degrees

Coolant Crossover Pipe Bolt – Front 50 Y 37 lb ft

Coolant Crossover Pipe Bolt – Side 10 Y 89 lb in

Coolant Drain Plug 19 Y 14 lb ft

Coolant Temperature Sensor 23 Y 17 lb ft

Crankshaft Balancer Bolt

Installation Pass Using the Old Bolt to Ensure the 125 Y 92 lb ft

First Pass – Install a NEW Bolt After the

Final Pass 130 degrees

Crankshaft Main Bearing Cap Bolt/Stud

Application Metric English

Final Pass 77 degrees

Crankshaft Oil Deflector Nut 25 Y 18 lb ft

Crankshaft Position Sensor Shield Nut 11 Y 98 lb in

Crankshaft Position Sensor Stud 11 Y 98 lb in

Cylinder Head Bolt

Final Pass 140 degrees

Drive Belt Idler Pulley Bolt – 13 mm 30 Y 22 lb ft

Drive Belt Idler Pulley Bolt – 15 mm 50 Y 37 lb ft

Drive Belt Idler Pulley Bolt

Upper Right and Lower Left 50 Y 37 lb ft

Drive Belt Tensioner Bolt 50 Y 37 lb ft

Engine Block Heater 50 Y 37 lb ft

Engine Block Plug 60 Y 44 lb ft

Engine Front Cover Bolt 25 Y 18 lb ft

Engine Lift Bracket Bolt 70 Y 52 lb ft

Engine Mount Bolts 50 Y 37 lb ft

Engine Mount Bracket Bolts

Bracket to Engine Block 90 Y 66 lb ft

Application Metric English

Bracket to Oil Pan 50 Y 37 lb ft

Engine Mount Bracket Lower Bolts 50 Y 37 lb ft

Engine Mount Bracket Upper Bolts 90 Y 66 lb ft

Engine Mount Nuts 50 Y 37 lb ft

Engine Mount Strut Bolts 50 Y 37 lb ft

Engine Mount Strut Bracket to Engine Bolts 25 Y 18 lb ft

Engine Oil Pressure Switch 16 Y 12 lb ft

Engine Wiring Harness Bracket Bolt 13 Y 115 lb in

Engine Wiring Harness Ground Terminal Nut 25 Y 18 lb ft

EVAP Purge Valve Bolt 12 Y 106 lb in

Exhaust Crossover Heat Shield Bolts 10 Y 89 lb in

Exhaust Crossover Pipe Nuts 25 Y 18 lb ft

Exhaust Crossover Pipe Studs 25 Y 18 lb ft

Exhaust Manifold Bolt 20 Y 15 lb ft

Exhaust Manifold Heat Shield Bolt 10 Y 89 lb in

Exhaust Manifold Lower Heat Shield Bolt 10 Y 89 lb in

Manual Transmission – First Pass 50 Y 37 lb ft

Manual Transmission – Final Pass 70 degrees