1

Computer Aided Design Tutorial No. 2

Table of Contents:

Auto CAD Command for Tutorial Figure P2.1............................................ 2

Auto CAD Command for Tutorial Figure P2.2 ........................................... 4

Auto CAD Command for Tutorial Figure P2.3 ........................................... 6

Auto CAD Command for Tutorial Figure P2.4 ........................................... 7

Auto CAD Command for Tutorial Figure P2.5 ........................................... 9

Auto CAD Command for Tutorial Figure P2.6 .......................................... 11

Auto CAD Command for Tutorial Figure P2.7 ......................................... 14

Auto CAD Command for Tutorial Figure P2.8 ......................................... 16

Auto CAD Command for Tutorial Figure P2.9 ......................................... 19

Auto CAD Command for Tutorial Figure P2.10 ....................................... 21

Fuuchae Er.
 2

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.1

Command: line
Specify first point: 0, 2
Specify next point: @0, 3
Specify next point: @0.5, 0
Specify next point: @2.5,-3
Specify next point: @1, 0
Specify next point:
Command: ray
Specify start point: 4, 0
Specify through point: 0, 0
Specify through point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ang
Enter angle of xline: 120
Specify through point: 0, 2
Specify through point:
Command: trim
Select cutting edges ...
Select objects: 1 found
Select objects:
Select object to trim:
Select object to trim:
Command: trim
Select cutting edges...
Select objects: 1 found
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Select object to trim:
Command: circle
Specify center point for circle: 1, 3
Specify radius of circle or [Diameter]: d
Specify diameter of circle: 0.875
Command: circle
Specify center point for circle: 1.5,2
Specify radius of circle or [Diameter]: d
Specify diameter of circle: 0.375

Fuuchae Er.
 3

Computer Aided Design Tutorial No. 2

Command: circle
Specify center point for circle: 1.5,1
Specify radius of circle or [Diameter]: d
Specify diameter of circle: 0.375
Command: mirror
Select objects: Specify opposite corner: 9 found
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No]: n
Command: circle
Specify center point for circle: 4, 0.875
Specify radius of circle or [Diameter]: d
Specify diameter of circle: 1.125

Fuuchae Er.
 4

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.2

Command: line
Specify first point: 2, 0
Specify next point: @11.29, 0
Specify next point: @5.37<51
Specify next point: @6.04<119
Specify next point: @3.23<166
Specify next point: @8.58<180
Specify next point: @2.41<-90
Specify next point: @6.73<0
Specify next point: @3.03<-90
Specify next point: @7.13<199
Specify next point or [Close]: c
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ver
Specify through point: 2, 0
Specify through point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: offset
Specify offset distance: 5.18
Select a line object:
Specify side to offset:
Select a line object:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: offset
Specify offset distance: 2.25
Select a line object:
Specify side to offset:
Select a line object:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ang
Enter angle of xline (0) or [Reference]: r
Select a line object:
Enter angle of xline: 90
Specify through point:
Specify through point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: offset
Specify offset distance: 5

Fuuchae Er.
 5

Computer Aided Design Tutorial No. 2

Select a line object:

Specify side to offset:
Select a line object:
Command: circle
Specify center point for circle:
Specify radius of circle: 0.75
Command: circle
Specify center point for circle:
Specify radius of circle: 0.75
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: erase
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
Select objects:
Command: trim
Select cutting edges...
Select objects: 1 found
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Select object to trim:

Fuuchae Er.
 6

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.3

Command: circle
Specify center point for circle: 4, 4
Specify radius of circle: 0.5
Command: circle
Specify center point for circle: 4, 5.5
Specify radius of circle: 0.45
Command: circle
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: ttr
Specify point on object for first tangent of circle:
Specify point on object for second tangent of circle:
Specify radius of circle: 0.275
Command: circle
Specify center point for circle: 4, 2.5
Specify radius of circle: 0.45
Command: array
Select objects: 1 found
Select objects:
Command: circle
Specify center point for circle: 6, 5.5
Specify radius of circle: 0.5
Command: circle
Specify center point for circle: 6, 5.5
Specify radius of circle: 0.75
Command: mirror
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No] <N>: n
Command: circle
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: ttr
Specify point on object for first tangent of circle:
Specify point on object for second tangent of circle:
Specify radius of circle: 3
Fuuchae Er.
 7

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.4

Command: line
Specify first point: 0, 0
Specify next point: @5, 0
Specify next point:
Command: arc
Specify start point of arc or [Center]: c
Specify center point of arc: 5, 1.5
Specify start point of arc: 5, 0
Specify end point of arc: 6.5, 1.5
Command: arc
Specify start point of arc or [Center]: c
Specify center point of arc: 5.5, 1.5
Specify start point of arc: 6.5, 1.5
Specify end point of arc: 5.5, 2.5
Command: line
Specify first point: @0, 0
Specify next point: @0, 1
Specify next point: @1, 0
Specify next point:
Command: arc
Specify start point of arc or [Center]: c
Specify center point of arc: 7.5, 3.5
Specify start point of arc: 7.5, 4.5
Specify end point of arc: 6.5, 3.5
Command: line
Specify first point: 7.5, 4.5
Specify next point: @0, 1
Specify next point:
Command: arc
Specify start point of arc or [Center]: c
Specify center point of arc: 6.5, 5.5
Specify start point of arc: 7.5, 5.5
Specify end point of arc: 6.5, 6.5
Command: line
Specify first point: @0, 0
Specify next point: @0,-1
Specify next point: @-2, 0
Fuuchae Er.
 8

Computer Aided Design Tutorial No. 2

Specify next point:

Command: arc
Specify start point of arc or [Center]: c
Specify center point of arc: 3, 5.5
Specify start point of arc: 1.5, 5.5
Specify end point of arc: 4.5, 5.5
Command: line
Specify first point: 1.5, 5.5
Specify next point: 0, 5.5
Specify next point: 0, 3
Specify next point:
Command: arc
Specify start point of arc or [Center]: c
Specify center point of arc: 0, 2
Specify start point of arc: 0, 1
Specify end point of arc: 0, 3
Command: line
Specify first point: 0, 1
Specify next point: 0, 0
Specify next point:
Command: chamfer
(TRIM mode) Current chamfer Dist1 = 0.0000, Dist2 = 0.0000
Select first line or [Undo/Polyline/Distance/Angle/Trim/mEthod/Multiple]: d
Specify first chamfer distance: 0.5
Specify second chamfer distance: 0.5
Select first line:
Select second line:

Fuuchae Er.
 9

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.5

Command: ellipse
Specify axis endpoint of ellipse: 0, 4.5
Specify other endpoint of axis: 13, 4.5
Specify distance to other axis: 4.5
Command: polygon
Enter number of sides: 8
Specify center of polygon: 6.5, 4.5
Enter an option [Inscribed in circle/Circumscribed about circle]: c
Specify radius of circle: 3.5
Command: ellipse
Specify axis endpoint of ellipse: 5, 4.5
Specify other endpoint of axis: 8, 4.5
Specify distance to other axis: 0.5
Command: rotate
Select objects: 1 found
Select objects:
Specify base point:
Specify rotation angle: 45
Command: polygon
Enter number of sides: 6
Specify center of polygon: 4.5, 2.5
Enter an option [Inscribed in circle/Circumscribed about circle]: i
Specify radius of circle: 0.5
Command: circle
Specify center point for circle: 4.5, 2.5
Specify radius of circle or [Diameter]:
Command: array
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Command: polygon
Enter number of sides: 6
Specify center of polygon: 1.5, 4.5
Enter an option [Inscribed in circle/Circumscribed about circle]: i
Specify radius of circle: 1
Command: circle
Specify center point for circle: 1.5, 4.5
Specify radius of circle or [Diameter]:

Fuuchae Er.
 10

Computer Aided Design Tutorial No. 2

Command: mirror
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No]: n

Fuuchae Er.
 11

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.6

Command: circle
Specify center point for circle: 1, 1
Specify radius of circle: 0.75
Command: circle
Specify center point for circle: 1, 1
Specify radius of circle: 1
Command: circle
Specify center point for circle: 5.5, 2.5
Specify radius of circle: 0.5
Command: circle
Specify center point for circle: 5.5, 2.5
Specify radius of circle: 0.75
Command: copy
Select objects: 2 found
Select objects:
Specify base point: 5.5, 2.5
Specify second point: 5.5, 6.5
Specify second point:
Command: circle
Specify center point for circle: 6.5, 4.5
Specify radius of circle: 0.5
Command: circle
Specify center point for circle: 8.5, 4.5
Specify radius of circle: 0.5
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: trim
Select cutting edges ...
Select objects: 2 found
Select objects:
Select object to trim:
Select object to trim:

Fuuchae Er.
 12

Computer Aided Design Tutorial No. 2

Select object to trim:

Command: trim
Select cutting edges...
Select objects: 2 found
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: trim
Select cutting edges...
Select objects: 2 found
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: hor
Specify through point: 0, 5.5
Specify through point: 0, 3.5
Specify through point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ver
Specify through point: 9.5,0
Specify through point:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.0000
Select first object or [Undo/Polyline/Radius/Trim/Multiple]: r
Specify fillet radius: 0.5
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.5000
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.5000

Fuuchae Er.
 13

Computer Aided Design Tutorial No. 2

Select first object or [Undo/Polyline/Radius/Trim/Multiple]: r

Specify fillet radius: 0.75
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.7500
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.7500
Select first object or [Undo/Polyline/Radius/Trim/Multiple]: r
Specify fillet radius: 5
Select first object:
Select second object:

Fuuchae Er.
 14

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.7

Command: circle
Specify center point for circle: 20, 20
Specify radius of circle: 5
Command: circle
Specify center point for circle: 20, 90
Specify radius of circle: 5
Command: line
Specify first point: 55, 20
Specify next point: @-10, 0
Specify next point: @0,-20
Specify next point: 0, 0
Specify next point: 0,110
Specify next point: @40, 0
Specify next point: @0,-15
Specify next point: @15, 0
Specify next point:
Command: chamfer
Select first line or [Distance/Angle]: a
Specify chamfer length on the first line: 10
Specify chamfer angle from the first line: 45
Select first line:
Select second line:
Command: chamfer
Select first line or [Distance/Angle]: a
Specify chamfer length on the first line: 15
Specify chamfer angle from the first line: 45
Select first line:
Select second line:
Command: chamfer
(TRIM mode) Current chamfer Length = 15.0000, Angle = 45
Select first line:
Select second line:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.0000
Select first object or [Radius]: r
Specify fillet radius: 5
Select first object:
Select second object:

Fuuchae Er.
 15

Computer Aided Design Tutorial No. 2

Command: line
Specify first point: 55, 30
Specify next point: @-25, 0
Specify next point: @0, 50
Specify next point: @25, 0
Specify next point:
Command: chamfer
Select first line or [Distance/Angle]: d
Specify first chamfer distance: 5
Specify second chamfer distance: 10
Select first line:
Select second line:
Command: chamfer
(TRIM mode) Current chamfer Dist1 = 5.0000, Dist2 = 10.0000
Select first line:
Select second line:
Command: mirror
Select objects: 18 found
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No]: n
Command: circle
Specify center point for circle: 55, 55
Specify radius of circle: 10

Fuuchae Er.
 16

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.8

Command: circle
Specify center point for circle: 0, 0
Specify radius of circle: 0.25
Command: circle
Specify center point for circle: 0.45,0
Specify radius of circle: 0.25
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: xline
Specify a point:
Specify through point:
Specify through point:
Command: trim
Select cutting edges...
Select objects: 2 found
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Select object to trim:
Select object to trim:
Command: trim
Select cutting edges...
Select objects: 2 found
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Command: circle
Specify center point for circle: 0, 0
Specify radius of circle: 0.75
Command: circle
Specify center point for circle: 2.23,0
Specify radius of circle: 1.125
Command: circle
Specify center point for circle: 2.23,0

Fuuchae Er.
 17

Computer Aided Design Tutorial No. 2

Specify radius of circle: 1.8

Command: circle
Specify center point for circle: 4.85, 0.9
Specify radius of circle: 0.56
Command: circle
Specify center point for circle: 4.85, 0.9
Specify radius of circle: 1.18
Command: copy
Select objects: 2 found
Select objects:
Specify base point: 4.85, 0.9
Specify second point: 2.98, 3.12
Specify second point:
Command: fillet
Select first object or [Radius]: r
Specify fillet radius: 0.5
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 0.5000
Select first object:
Select second object:
Command: fillet
Select first object or [Radius]: r
Specify fillet radius: 1.12
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 1.1200
Select first object:
Select second object:
Command: fillet
Current settings: Mode = TRIM, Radius = 1.1200
Select first object:
Select second object:
Command: trim
Select cutting edges...
Select objects: 5 found
Select objects:
Select object to trim:

Fuuchae Er.
 18

Computer Aided Design Tutorial No. 2

Select object to trim:

Select object to trim:
Select object to trim:
Select object to trim:

Fuuchae Er.
 19

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.9

Command: line
Specify first point: 0, 1.46
Specify next point: 0, 0
Specify next point: 4.06,0
Specify next point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ang
Enter angle of xline: 15
Specify through point: 4.06,0
Specify through point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ver
Specify through point: 5.66,0
Specify through point: 6.3,0
Specify through point:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: ang
Enter angle of xline: 45
Specify through point:
Specify through point:
Command: erase
Select objects: 1 found
Select objects:
Command: trim
Select cutting edges ...
Select objects: 2 found
Select objects:
Select object to trim:
Select object to trim:
Command: xline
Specify a point or [Hor/Ver/Ang/Bisect/Offset]: hor
Specify through point: 0, 1.26
Specify through point: 0, 1.46
Specify through point: 0, 2.06
Specify through point:
Command: circle
Specify center point for circle: 3, 2.86
Specify radius of circle: 2

Fuuchae Er.
 20

Computer Aided Design Tutorial No. 2

Command: circle
Specify center point for circle: 3, 1.26
Specify radius of circle: 0.4
Command: line
Specify first point: 5.36, 2.06
Specify next point: 5.36, 1.26
Specify next point:
Command: trim
Select cutting edges ...
Select objects:
Select objects:
Select object to trim:
Select object to trim:
Select object to trim:
Select object to trim:
Command: erase
Select objects: 1 found
Select objects:
Command: fillet
Select first object or [Radius]: r
Specify fillet radius: 0.56
Select first object:
Select second object:
Command: fillet
Select first object or [Radius]: r
Specify fillet radius: 0.25
Select first object:
Select second object:
Command: mirror
Select objects: 12 found
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No]: n
Command: circle
Specify center point for circle: 0.56, 0.56
Specify radius of circle: 0.25
Command: array
Select objects: 1 found
Select objects:

Fuuchae Er.
 21

Computer Aided Design Tutorial No. 2

Auto CAD Command for Tutorial Figure P2.10

Command: rectangle
Specify first corner point: 0, 0
Specify other corner point: 225,140
Command: polygon
Enter number of sides: 6
Specify center of polygon: 50, 70
Enter an option [Inscribed in circle/Circumscribed about circle]: i
Specify radius of circle: 20
Command: polygon
Enter number of sides: 8
Specify center of polygon: 160, 70
Enter an option [Inscribed in circle/Circumscribed about circle]: i
Specify radius of circle: 30
Command: line
Specify first point: 225,140
Specify next point: 265,200
Specify next point: @-315, 0
Specify next point: 0,140
Specify next point:
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 230,200
Specify second break point: @-35, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 160,200
Specify second break point: @-35, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 90,200
Specify second break point: @-35, 0
Command: break
Select object:
Specify second break point or [First point]: f
Fuuchae Er.
 22

Computer Aided Design Tutorial No. 2

Specify first break point: 20,200

Specify second break point: @-35, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 0,140
Specify second break point: @25, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 50,140
Specify second break point: @25, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 100,140
Specify second break point: @25, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 150,140
Specify second break point: @25, 0
Command: break
Select object:
Specify second break point or [First point]: f
Specify first break point: 200,140
Specify second break point: @25, 0
Command: line
Specify first point:
Specify next point or [Undo]:
Specify next point or [Undo]:
Command: line
Specify first point:
Specify next point or [Undo]:
Specify next point or [Undo]:
Command: line
Specify first point:
Specify next point or [Undo]:
Specify next point or [Undo]:
Command: line

Fuuchae Er.
 23

Computer Aided Design Tutorial No. 2

Specify first point:

Specify next point or [Undo]:
Specify next point or [Undo]:
Command: line
Specify first point:
Specify next point or [Undo]:
Specify next point or [Undo]:

Fuuchae Er.