Scribd
Upload
716 views2 pages

Boss OD-2 Turbo OverDrive

The document provides the schematic diagram for the Boss OD-2 Turbo OverDrive guitar effects pedal. It has 3 potentiometers to control level, drive, and tone, and a switch to select between two modes of operation - one similar to the OD-1 pedal, and a "turbo mode" that produces more gain and distortion. The schematic shows the circuit diagram and lists the transistors, diodes, and other components used in the OD-2 pedal.

Uploaded by

Tiago Rech
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
716 views2 pages

Boss OD-2 Turbo OverDrive

The document provides the schematic diagram for the Boss OD-2 Turbo OverDrive guitar effects pedal. It has 3 potentiometers to control level, drive, and tone, and a switch to select between two modes of operation - one similar to the OD-1 pedal, and a "turbo mode" that produces more gain and distortion. The schematic shows the circuit diagram and lists the transistors, diodes, and other components used in the OD-2 pedal.

Uploaded by

Tiago Rech
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Electronics > Schematic diagrams > Guitar effects > Boss OD-2 Turbo OverDrive schematic

Boss OD-2 Turbo OverDrive pedal schematic diagram


The OD-2 was manufactured as a replacement for the OD-1 in the mid-1980s and uses only discrete components. It has 3 potentiometers for level, drive, tone control and a switch for selecting
two modes of operation. When set to the OFF position the sound is similar to the OD-1 but in the turbo mode it generates more gain and distortion.

Fig. 1: Boss OD-2 Turbo OverDrive guitar pedal schematic diagram

Controls: Level, Tone, Drive, 2-way Mode switch


Connectors: Input, Output, AC Adaptor
Input Impedance: 1Mohm
Output Load Impedance: 10kohm or more
Equivalent Input Noise: -118dBm or less (IHF-A, Tone
center, Input Short)
Recommended AC Adaptor: ACA Series
Current Draw: 10mA @ 9V
Dimensions: 70(W) x 55(H) x 125(D)mm
Weight: 410g (14 oz.)

Transistors and diodes used in the OD-2 Turbo OverDrive:

Q1, Q6, Q8, Q9, Q21: 2SC945-P (NPN silicon transistors)


Q3, Q4, Q7, Q16, Q17: 2SK30A-Y (N-channel JFET transistors)
Q5, Q10, Q11, Q13, Q14, Q18, Q19: 2SK117-GR (N-channel JFET transistors)
Q12, Q15, Q20: 2SA970-GR (PNP silicon transistors)
Q2: 2SC2240-GR (NPN silicon transistor)
D1, D3-D5, D7, D9-D12: 1SS-133 (switching diodes)
D2: S5500G (400V/1A rectifier diode)
D6: RD6.2JB-2 (6.2V Zener diode)
Fig. 2: Boss OD-2 Turbo OverDrive circuit board - component side and foil side
D8: MTZ6.6 (6.6V Zener diode)
LED: LN28RP (red LED)
Boss CE-2 Chorus Pearl FG-01 Flanger CS-2 Compression Sustainer Boss NF-1 Noise Gate
CE-2B Bass Chorus Boss OD-1 Overdrive Boss DM-2 Analog Delay Boss GE-7 Equalizer
Arion SCH-1 Chorus Boss SD-1 Super Overdrive Boss DD-2 Digital Delay Boss GE-7B Bass Equalizer
Pearl CH-02 Chorus Boss MT-2 Metal Zone Boss OC-2 Octave Boss TR-2 Tremolo
Boss BF-2 Flanger Boss HM-2 Heavy Metal

SepElectronics
PCB manufacturing
Conformal coating

Website Directions

Electronics > Schematic diagrams > Guitar effects > Boss OD-2 Turbo OverDrive guitar pedal schematic

You might also like