BRX System Deployment Guide Interactive
BRX System Deployment Guide Interactive
BRX 300
S E R I E S
BRX308-LA
BRX325SP
BRX308-ACC
BRX308-AF
BRX308-PM
TABLE OF CONTENTS
1. SAFETY 3
2. ORDERING INFORMATION 6
SAFETY
Before using a JBL BRX Series system, please review the following for important information on safety and protection of your investment.
2.1 - SAFETY INSTRUCTIONS
1. 1. Read these instructions
2. Keep these instructions
3. Heed all warnings
4. Follow all instructions
5. Do not expose the product to direct rain or sea spray
6. Clean only with a dry cloth
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat
8. Only use attachments / accessories specified by the manufacturer
9. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use
caution when moving the cart / apparatus combination to avoid injury from tip-over
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as liquid
has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate nor-
mally, or has been dropped
11. Contact JBL Professional for advanced servicing issues
12. CAUTION - DO NOT PERFORM ANY SERVICING UNLESS YOU ARE QUALIFIED TO DO SO
13. Prolonged exposure to excessive SPL can cause hearing damage: the loudspeaker is easily capable of generating sound pressure levels
(SPL) sufficient to cause permanent hearing damage to performers, production crew and audience members. Caution should be taken to
avoid prolonged exposure to SPL in excess of 90 dB
14. Read the System Rigging Manual before installation and use of the product.
15. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
16. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the oth-
er. A grounding-type plug has two blades and a third grounding prong. The wide an electrician for replacement of the obsolete outlet.
17. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit
from the apparatus.
18. Unplug this apparatus during lightning storms or when unused for long periods of time.
19. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle.
20. “WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.”
21. Do not expose this equipment to dripping or splashing and ensure that no object s filled with liquids such as vases, are placed on the
equipment.
22. The main plug of the power supply cord shall remain readily operable.
The lighting flash with Arrowhead Symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “Danger-
ous Voltage” within the product’s enclosure that may be of sufficient magitude to onstitute risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operatingand maintenance(ser-
vicing) information in the literature accompanying the product.
ORDERING INFORMATION
BRX325SP Dual 15” Subwoofer with Power Amplifier and DSP for entire system
BRX308-ACC Accessory Kit - Transport cart for 4 x BRX308-LA, Soft cover for Cart, Soft cover for
Subwoofer, Speaker cables for system
The BRX300 System is a true plug and play solution that features a combination of the BRX308-LA Dual 8”
2 Way Line array Element and the BRX325SP Dual 15” Subwoofer that also houses a 6 Channel High Power
Amplifier along with a 48kHz/24 bit DSP for Loudspeaker tuning. All the components are packaged to maximize
use of space and ease of handling and Set-up.
The power and processing Module features BSS Audio Processing for the Subwoofer and 2 circuits of 2 x BRX
08LA each including linear phase FIR Filters and dbx limiter suite for Loudspeaker protection. As such, no
external processing is required .
NOTE: BRX Speakers used with other Amplification and DSP will VOID the WARRANTY of the system.
This System is primarily intended for Ground stack use ( 4 x BRX308-LA + 1 x BRX25SP) and Pole stacked ( 2 x
BRX308-LA + 1 x BRX325SP with the BRX308-PM Pole and Adapter kit).
There is a third option of use as a Flown System ( Up to 8 x BRX308-LA suspended from 1 x BRX308-AF). The
subwoofers either remain stacked on the ground or 1 x BRX325SP Subwoofer may be flown on its own Array
Frame. Each Subwoofer can power up to 4 x BRX308-LA using the built in Power Module.
NOTE: BRX Speakers used with other Amplification and DSP will VOID the WARRANTY of the system.
The below image shows the connection diagram for the BRX308-LA Tops from the Amplifier and DSP Module.
Each output on the Power Amplifier module can drive up to 2 x BRX308-LA Tops.
MAX 4x BRX308-LA
The most common use case for the BRX308 System is the ground Stacked mode as shown above.
It is advised to use an inter-box angle of at least 2° between each BRX308-LA to allow for wide enough
vertical coverage of the High Frequency.
The BRX308-LA has captive rigging hardware that allows for inter box
angles of 0,1,2,3,4,5,6,8,10 and 12°.
To set the inter box angle to either of the values mentioned above,
align the Bottom box Angle Bar ‘Lock’ hole to match with the desired
angle value on the Top Box and lock it in place with the Quick release
pin.
When setting inter box angles of 8° and above, the angle bar of the
upper box may obstruct the angle bar from the below box from align-
ing with the desired value. In such cases, the angle bar of the upper
box must be stored using the Quick release pin in the ‘Standby’ hole.
Angle Bar
The Pole Mount adapter bar allows for the following angles 0,-2,-3,-4,-,5,-6,-8,-9,-10,-
11,-12° for the first box mounted on it. The negative angles allow the first box to aim
downwards and cover audience that is closer to the array.
To set the first box at the desired –ve angle value, Align the desired value on the
Adapter bar to the bottom of the box and lock in place with the quick release pin in
the matching hole.
We recommend an inter-box Angle of 10 or 12° for the second Speaker. This allows for
more uniform coverage from front to back.
Adapter Bar
MAX 1x BRX325-SP
MAX 8x BRX308LA
> 8x BRX308LA
Note: It is not possible to fly a hybrid system including Sub and Tops in a single array from a single Array Frame.
If the Subwoofer must be flown to minimize cabling or due to aesthetic reasons, the sub must be flown next
to the tops. If flying the sub next to the tops is not possible, you may fly the subwoofer nehind the tops. In this
case, an external signal processor will be needed to add delay to the tops so that the Front grills of the sub and
tops are vitually aligned in distance.
AF Angle Top angle of the array frame. This is usually a -ve angle for speakers aimed downward.
Box 1 This angle is always ‘0” as this is attached to the array frame.
Box 2 This is the inter box angle between Box 1 and Box 2
Box 3 This is the inter box angle between Box 2 and Box 3
Box 4...8 As above
No. of Boxes 8
AF Pick Point Hole 12
AF Angle -5 Degrees
Box 1 0
Box 2 1
Box 3 1
Box 4 2
Box 5 1
Box 6 3
Box 7 4
Box 8 12
2. 6x BRX308-LA for a 25~30m(82~98 ft.) deep venue flown at a height of 4m(13 ft.)
No. of Boxes 6
AF Pick Point Hole 9
AF Angle -4.3 Degrees
Box 1 0
Box 2 0
Box 3 1
Box 4 1
Box 5 3
Box 6 10