Material Safety Data Sheet Enriching lives through innovation

ARADUR® 22962

1. Product and company identification

Product name : ARADUR® 22962
Material uses : Formulated hardener for structural composites
MSDS # : 00056129
Validation date : 9/15/2011.
Print date : 9/15/2011.

Supplier/Manufacturer : Huntsman Advanced Materials Americas LLC

P.O. Box 4980
The Woodlands, TX 77387

Non-Emergency phone: (800) 257-5547

E-Mail: [email protected]

In case of emergency : Chemtrec: (800) 424-9300 or (703) 527-3887

2. Hazards identification
Physical state : Liquid.
Odor : Slight
Color : Colorless.

OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Emergency overview : DANGER!
CAUSES EYE AND SKIN BURNS. CAUSES RESPIRATORY TRACT IRRITATION.
MAY CAUSE ALLERGIC SKIN REACTION. MAY BE HARMFUL IF SWALLOWED.
CAN ENTER LUNGS AND CAUSE DAMAGE.
Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not breathe
vapor or mist. Do not ingest. Do not get in eyes or on skin or clothing. Use only with
adequate ventilation. Keep container tightly closed and sealed until ready for use. Wash
thoroughly after handling.
See toxicological information (Section 11)

GENERAL INFORMATION : Read the entire MSDS for a more thorough evaluation of the hazards.

3. Composition/information on ingredients
Name CAS number %
Isophorone diamine 2855-13-2 60 - 100

9/15/2011. 00056129 1/9

ARADUR® 22962

4. First aid measures

Eye contact : Check for and remove any contact lenses. Immediately flush eyes with plenty of water
for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical
attention immediately.
Skin contact : In case of contact, immediately flush skin with plenty of water for at least 15 minutes
while removing contaminated clothing and shoes. Wash clothing before reuse. Clean
shoes thoroughly before reuse. Get medical attention immediately.
Inhalation : Move exposed person to fresh air. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention
immediately.
Ingestion : Wash out mouth with water. Do not induce vomiting unless directed to do so by medical
personnel. Never give anything by mouth to an unconscious person. Get medical
attention immediately.

Notes to physician : Symptomatic and supportive therapy as needed. Following severe exposure medical
follow-up should be monitored for at least 48 hours.

5. Fire-fighting measures
Flash point : Closed cup: 110°C (230°F) [DIN 51758 EN 22719 (Pensky-Martens Closed Cup)]
Flammable limits : Lower: 1.2%
Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
nitrogen oxides
Extinguishing media
Suitable : Use an extinguishing agent suitable for the surrounding fire.
Not suitable : None known.
Special exposure hazards : Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training.

Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing
equipment for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.

6. Accidental release measures

Personal precautions : No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Do not breathe vapor or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment (see Section 8).
Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Methods for cleaning up : Stop leak if without risk. Move containers from spill area. Approach release from
upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash
spillages into an effluent treatment plant or proceed as follows. Contain and collect
spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or
diatomaceous earth and place in container for disposal according to local regulations
(see section 13). Dispose of via a licensed waste disposal contractor. Contaminated
absorbent material may pose the same hazard as the spilled product. Note: see section
1 for emergency contact information and section 13 for waste disposal.

9/15/2011. 00056129 2/9

ARADUR® 22962

7. Handling and storage

Handling : Put on appropriate personal protective equipment (see Section 8). Eating, drinking and
smoking should be prohibited in areas where this material is handled, stored and
processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas.
Persons with a history of skin sensitization problems should not be employed in any
process in which this product is used. Do not get in eyes or on skin or clothing. Do not
breathe vapor or mist. Do not swallow. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Keep in the original container or
an approved alternative made from a compatible material, kept tightly closed when not in
use. Keep away from acids. Empty containers retain product residue and can be
hazardous. Do not reuse container.
Storage : Store between the following temperatures: 2 to 40°C (35.6 to 104°F). Store in
accordance with local regulations. Store in original container protected from direct
sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see
section 10) and food and drink. Separate from acids. Keep container tightly closed and
sealed until ready for use. Containers that have been opened must be carefully resealed
and kept upright to prevent leakage. Do not store in unlabeled containers. Use
appropriate containment to avoid environmental contamination.

8. Exposure controls/personal protection

Consult local authorities for acceptable exposure limits.
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace atmosphere
procedures or biological monitoring may be required to determine the effectiveness of the ventilation
or other control measures and/or the necessity to use respiratory protective equipment.
Engineering measures : Use only with adequate ventilation. If user operations generate dust, fumes, gas, vapor
or mist, use process enclosures, local exhaust ventilation or other engineering controls
to keep worker exposure to airborne contaminants below any recommended or statutory
limits.
Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period. Appropriate
techniques should be used to remove potentially contaminated clothing. Contaminated
work clothing should not be allowed out of the workplace. Wash contaminated clothing
before reusing. Ensure that eyewash stations and safety showers are close to the
workstation location.
Personal protection
Respiratory : In case of inadequate ventilation wear respiratory protection. Respirator selection must
be based on known or anticipated exposure levels, the hazards of the product and the
safe working limits of the selected respirator.
Hands : Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. >8 hours (breakthrough time): butyl rubber, Ethyl Vinyl Alcohol Laminate
(EVAL)
Eyes : Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists or
dusts.
Skin : Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before handling
this product.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure they
controls comply with the requirements of environmental protection legislation. In some cases,
fume scrubbers, filters or engineering modifications to the process equipment will be
necessary to reduce emissions to acceptable levels.

9/15/2011. 00056129 3/9

ARADUR® 22962

9. Physical and chemical properties

General information
Appearance
Physical state : Liquid.
Color : Colorless.
Odor : Slight
Important health, safety and environmental information
pH : 13 [Conc. (% w/w): 50%]
Boiling/condensation point : >200°C (>392°F)
Melting/freezing point : Not available.
Flash point : Closed cup: 110°C (230°F) [DIN 51758 EN 22719 (Pensky-Martens Closed Cup)]
Flammable limits : Lower: 1.2%
Auto-ignition temperature : 380°C (716°F)
Decomposition : >200°C (>392°F)
temperature

Vapor pressure : <0.002 kPa (<0.015 mm Hg) [20°C]

Specific gravity : 0.92 to 0.925
Water solubility : 1000 g/l 23.8 deg C
Water solubility : miscible
Partition coefficient: n- : 0.99
octanol/water (log Kow)
Viscosity : Dynamic: 5 to 20 mPa·s (5 to 20 cP)
Kinematic: 0.19 cm2/s (19 cSt)
Density : 0.92 g/cm3 [25°C (77°F)]
Vapor density : Not available.
Evaporation rate (butyl : Not available.
acetate = 1)
VOC : Not available.

10 . Stability and reactivity

Chemical stability : The product is stable.
Under normal conditions of storage and use, hazardous reactions will not occur.

Hazardous polymerization : Under normal conditions of storage and use, hazardous polymerization will not occur.
Conditions to avoid : No specific data.
Materials to avoid : strong acids, strong bases, strong oxidising agents
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should
products not be produced.

11 . Toxicological information
Potential acute health effects
Inhalation : Severely irritating to the respiratory system.
Ingestion : Harmful if swallowed. Aspiration hazard if swallowed. Can enter lungs and cause
damage. May cause burns to mouth, throat and stomach.
Skin : Corrosive to the skin. Causes burns. May cause sensitization by skin contact.
Eyes : Corrosive to eyes. Causes burns.

9/15/2011. 00056129 4/9

ARADUR® 22962

11 . Toxicological information
Acute toxicity
Product/ingredient name Result Species Dose Exposure
Isophorone diamine LD50 Oral Rat 1000 mg/kg -

Sensitizer
Product/ingredient name Route of Species Result
exposure
Isophorone diamine skin Guinea pig Sensitizing

Potential chronic health effects

Chronic effects : Once sensitized, a severe allergic reaction may occur when subsequently exposed
to very low levels.
Target organs : Not available.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Medical conditions aggravated by over-
exposure
Pre-existing skin disorders may be aggravated by over-exposure to this product.

12 . Ecological information

Environmental effects : Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic
environment. This product shows a low bioaccumulation potential.
Aquatic ecotoxicity
Product/ingredient name Test Result Species Exposure
Isophorone diamine DIN 38412 Acute EC50 42 Daphnia - 24 hours
(Lumistox test) mg/L Daphnia magna
Straus 1820
DIN 38412 Acute EC50 37 Algae - 72 hours
(Lumistox test) mg/L Scenedesmus
subspicatus
Not known Acute LC50 185 Fish - Golden 48 hours
mg/L orfe (Leuciscus
idus)
203 Fish, Acute Acute LC50 110 Fish - Zebra fish 96 hours
Toxicity Test mg/L (Brachydanio
rerio)
Biodegradability
Other ecological information
Not Determined
Not Determined
Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
Isophorone diamine 0.99 - low

9/15/2011. 00056129 5/9

ARADUR® 22962

12 . Ecological information
Other adverse effects : No known significant effects or critical hazards.
PBT : Not applicable.
Other information

13 . Disposal considerations
Waste disposal : The generation of waste should be avoided or minimized wherever possible. Significant
quantities of waste product residues should not be disposed of via the foul sewer but
processed in a suitable effluent treatment plant. Dispose of surplus and non-recyclable
products via a licensed waste disposal contractor. Disposal of this product, solutions
and any by-products should at all times comply with the requirements of environmental
protection and waste disposal legislation and any regional local authority requirements.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers.
Disposal should be in accordance with applicable regional, national and local laws and regulations.

14 . Transport information
Proper shipping name
DOT : ISOPHORONEDIAMINE
TDG : ISOPHORONEDIAMINE
IMDG : ISOPHORONEDIAMINE
IATA : ISOPHORONEDIAMINE

Regulatory UN number Classes PG* Label Additional

information information
DOT Classification UN2289 8 III -

TDG Classification UN2289 8 III -

IMDG Class UN2289 8 III Emergency

schedules (EmS)
F-A, S-B

IATA-DGR Class UN2289 8 III Passenger and

Cargo Aircraft
Quantity limitation: 5 L
Packaging
instructions: 852
Cargo Aircraft Only
Quantity limitation:
60 L
Packaging
instructions: 856

9/15/2011. 00056129 6/9

ARADUR® 22962

14 . Transport information
PG* : Packing group

15 . Regulatory information
U.S. Federal regulations
HCS Classification : Corrosive material
Sensitizing material
U.S. Federal regulations : United States inventory (TSCA 8b): This material is listed or exempted.
TSCA 5(a)2 final significant : None.
new use rule (SNUR)
TSCA 5(e) substance : None.
consent order
TSCA 12(b) one-time : None.
export notification:
TSCA 12(b) annual export : None.
notification
SARA 302/304/311/312 : SARA 302/304/311/312 extremely hazardous substances: No Ingredient Listed
extremely hazardous
substances
SARA 311/312 hazard : SARA 311/312 MSDS distribution - chemical inventory - hazard identification:
identification Isophorone diamine: Immediate (acute) health hazard

Clean Air Act Section : Product name CAS number Concentration

112(b) Hazardous Air No Ingredients Listed.
Pollutants (HAPs)

Clean Air Act - Ozone : This product does not contain nor is it manufactured with ozone depleting substances.
Depleting Substances
(ODS)

SARA 313 No ingredients listed.

CERCLA: Hazardous substances.: No ingredients listed.

STATE REGULATIONS:
PENNSYLVANIA - RTK: This material is not listed.
California Prop 65 : This product contains no listed substances known to the State of California to cause
cancer, birth defects or other reproductive harm, at levels which would require a warning
under the statute.
Canada
WHMIS (Canada) : Class D-2B: Material causing other toxic effects (Toxic).
Class E: Corrosive material
CEPA DSL : This material is listed or exempted.
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations
and the MSDS contains all the information required by the Controlled Products Regulations.

9/15/2011. 00056129 7/9

 ARADUR® 22962

15 . Regulatory information
International lists : Australia inventory (AICS): This material is listed or exempted.
China inventory (IECSC): This material is listed or exempted.
Japan inventory: This material is listed or exempted.
Korea inventory: This material is listed or exempted.
New Zealand Inventory of Chemicals (NZIoC): Not determined.
Philippines inventory (PICCS): This material is listed or exempted.

16 . Other information
Label requirements : CAUSES EYE AND SKIN BURNS. CAUSES RESPIRATORY TRACT IRRITATION.
MAY CAUSE ALLERGIC SKIN REACTION. MAY BE HARMFUL IF SWALLOWED.
CAN ENTER LUNGS AND CAUSE DAMAGE.
Hazardous Material :
Information System (U.S.A.)
Health 3

Flammability 1

Physical hazards 0

Personal protection

The customer is responsible for determining the PPE code for this material.

National Fire Protection :

Association (U.S.A.)

1 Flammability
Health 3 0 Instability
Special

Date of printing : 9/15/2011.

Date of issue : 9/15/2011.
Date of previous issue : No previous validation.
Version : 1
Indicates information that has changed from previously issued version.
Notice to reader
While the information and recommendations in this publication are to the best of our knowledge, information and
belief accurate at the date of publication, NOTHING HEREIN IS TO BE CONSTRUED AS A WARRANTY, EXPRESS
OR OTHERWISE.

IN ALL CASES, IT IS THE RESPONSIBILITY OF THE USER TO DETERMINE THE APPLICABILITY OF SUCH
INFORMATION AND RECOMMENDATIONS AND THE SUITABILITY OF ANY PRODUCT FOR ITS OWN PARTICULAR
PURPOSE.

THE PRODUCT MAY PRESENT HAZARDS AND SHOULD BE USED WITH CAUTION. WHILE CERTAIN HAZARDS
ARE DESCRIBED IN THIS PUBLICATION, NO GUARANTEE IS MADE THAT THESE ARE THE ONLY HAZARDS THAT
EXIST.

Hazards, toxicity and behaviour of the products may differ when used with other materials and are dependent upon
9/15/2011. 00056129 8/9
 ARADUR® 22962

16 . Other information
the manufacturing circumstances or other processes. Such hazards, toxicity and behaviour should be determined
by the user and made known to handlers, processors and end users.

NO PERSON OR ORGANIZATION EXCEPT A DULY AUTHORIZED HUNTSMAN EMPLOYEE IS AUTHORIZED TO

PROVIDE OR MAKE AVAILABLE DATA SHEETS FOR HUNTSMAN PRODUCTS. DATA SHEETS FROM
UNAUTHORIZED SOURCES MAY CONTAIN INFORMATION THAT IS NO LONGER CURRENT OR ACCURATE. NO
PART OF THIS DATA SHEET MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM, OR BY ANY MEANS,
WITHOUT PERMISSION IN WRITING FROM HUNTSMAN. ALL REQUESTS FOR PERMISSION TO REPRODUCE
MATERIAL FROM THIS DATA SHEET SHOULD BE DIRECTED TO HUNTSMAN, MANAGER, PRODUCT SAFETY AT
THE ABOVE ADDRESS.

9/15/2011. 00056129 9/9

SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE

COMPANY/UNDERTAKING
Product information
Trade name : ARALDITE LY 564

Use : Formulated resin for structural composites

Company : Huntsman Advanced Materials (Europe)BVBA

Everslaan 45
3078 Everberg / Belgium
Telephone : +41619661599
Telefax : +41619661589
Emergency telephone : +32 35 751 234 (in France ORFILA : +33(0)145425959)
number

For further Product EHS related questions concerning this document or its contents, please
contact:
E-Mail: [email protected]

2. HAZARDS IDENTIFICATION
Irritating to eyes and skin.
May cause sensitization by skin contact.
Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.

3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical nature
Bisphenol A epoxy resin containing reactive diluent
preparation

Hazardous components
Chemical Name CAS-No. Symbol(s): R-phrase(s) Concentration [%]
butanedioldiglycidyl ether 2425-79-8 Xn R20/21 R36/38 R43 14.00 - 22.00
EC-No.: 219-371-7 R52/53
reaction product: bisphenol A- 25068-38- Xi, N R36/38 R43 R51/53 78.00 - 90.00
(epichlorhydrin); epoxy resin 6
(number average molecular
weight < 700)

4. FIRST AID MEASURES

Inhalation : Move to fresh air.
If symptoms persist, call a physician.

Eye contact : Rinse immediately with plenty of water for at least 15 minutes.
If eye irritation persists, consult a specialist.

Skin contact : Wash off with soap and plenty of water.

If skin irritation persists, call a physician.

1/7
SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

Ingestion : Immediately give plenty of water (if possible charcoal slurry).

If a person vomits when lying on his back, place him in the
recovery position.
Oxygen or artificial respiration if needed.
Do not induce vomiting.

5. FIRE-FIGHTING MEASURES
Suitable extinguishing : Water spray.
media Carbon dioxide (CO2).
Foam.
Dry powder.

Extinguishing media which : High volume water jet.

must not be used for safety
reasons
Special protective : Wear self-contained breathing apparatus and protective suit.
equipment for fire-fighters
Further information : Burning produces obnoxious and toxic fumes.
Carbon oxides.

6. ACCIDENTAL RELEASE MEASURES

Personal precautions : Keep away from sources of ignition - No smoking.
Avoid contact with skin, eyes and clothing.
Do not breathe vapours/dust.

Environmental precautions : Prevent product from entering drains.

Do not contaminate surface water.
Avoid subsoil penetration.

Methods for cleaning up : Soak up with inert absorbent material and dispose of as
hazardous waste.

7. HANDLING AND STORAGE

Handling
Advice on safe handling : Provide sufficient air exchange and/or exhaust in work rooms.
Ensure adequate ventilation.
Handle and open container with care.

Storage
Further information on : Keep away from food, drink and animal feeding stuffs.
storage conditions Keep container tightly closed.
Store at room temperature in the original container.

Storage hazard class : Storage class 10, Environmentally hazardous liquids

2/7
SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

Huntsman Advanced
Materials

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

Components with workplace control parameters
Components CAS-No. Control Update Basis
parameters

Personal protective equipment

Respiratory protection : In case of insufficient ventilation wear suitable respiratory
equipment.
Filter type AX-P2 (organic vapours, particles)

Eye protection : Tightly fitting safety goggles.

Face-shield.

Hand protection : Material of gloves for long term application (BTT>480 min):
Butyl rubber
Ethyl Vinyl Alcohol Laminate (EVAL)
Material of gloves for short term/splash application (10
min<BTT<480 min):
Nitrile rubber
Neoprene rubber
Use gloves approved to relevant standards e.g. EN 374
(Europe), F739 (US).
Suitability and durability of a glove is dependent on usage, e.g.
frequency and duration of contact, chemical resistance of glove
material and dexterity. Always seek advice from glove
suppliers.
Additonal information can be found for instance at
www.gisbau.de

Skin and body protection : Protective suit.

Safety shoes.

Protective measures : Keep away from sources of ignition - No smoking.

Avoid contact with skin, eyes and clothing.

9. PHYSICAL AND CHEMICAL PROPERTIES

Form : liquid

Colour : yellow

Odour : slight

pH : 7.7
at (20 °C)
1:1 in water

Boiling point : > 200 °C

3/7
SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

Thermal decomposition : > 200 °C

Flash point : 185 °C

Method: DIN 51758 (Pensky-Martens Closed Cup)

Vapour pressure : 0.3 Pa

at 20 °C

Density : 1.1 - 1.2 g/cm3

at 25 °C

Water solubility : at 20 °C
Note: practically insoluble

Miscibility with water : immiscible

Viscosity, dynamic : 1,000 - 1,400 mPa.s

at 25 °C

10. STABILITY AND REACTIVITY

Conditions to avoid : Note: Take necessary action to avoid static electricity
discharge.

Materials to avoid : Strong acids and strong bases.

Strong oxidizing agents.

Hazardous decomposition : Carbon oxides. Burning produces obnoxious and toxic fumes.
products

11. TOXICOLOGICAL INFORMATION

Acute oral toxicity : LD50 rat
Dose: > 5,000 mg/kg

Eye irritation : irritating

rabbit

Skin irritation : irritating

rabbit
dermal

Sensitization : Causes sensitization.

guinea pig

12. ECOLOGICAL INFORMATION

Ecotoxicity effects

Further information on ecology

4/7
SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

Additional ecological : Avoid subsoil penetration.

information Prevent product from entering drains.
Do not contaminate surface water.

13. DISPOSAL CONSIDERATIONS

Product : Waste Key Number: 070208
Must be incinerated, when in compliance with local regulations.

Container : Empty containers can be landfilled after cleaning, when in

compliance with the Environmental Protection (Duty of Care)
Regulations 1991.

14. TRANSPORT INFORMATION

Land transport

ADR:
UN-No: 3082
Class: 9
Classification code: M6
Packaging group: III
Risk No.: 90
ADR/RID-Labels: 9
Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,
N.O.S.
contains: BISPHENOL A EPOXY RESIN

RID:
UN-No: 3082
Class: 9
Packaging group: III
Risk No.: 90
ADR/RID-Labels: 9
Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,
N.O.S.
contains: BISPHENOL A EPOXY RESIN

Sea transport

IMDG:
UN-No: 3082
Class: 9
Packaging group: III
ADR/RID-Labels: 9
MFAG:
EmS: F-A S-F
Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,
N.O.S.
contains: (BISPHENOL A EPOXY RESIN)

5/7
SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

Air transport

IATA-DGR:
UN/ID No.: UN 3082
Class: 9
Packaging group: III
Packing instruction (cargo 914
aircraft):
Max. Qty/Pack.: 450.00 L
( 999.00 = No limit )
Packing instruction 914
(passenger aircraft):
Max. Qty/Pack.: 450.00 L
( 999.00 = No limit )
ADR/RID-Labels: 9
Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,
N.O.S.
contains: (BISPHENOL A EPOXY RESIN)

15. REGULATORY INFORMATION

Labelling according to EEC Directive
Labelling required

Symbol(s): : Xi Irritant
N Dangerous for the environment

R-phrase(s) : R36/38 Irritating to eyes and skin.

R43 May cause sensitization by skin contact.
R51/53 Toxic to aquatic organisms, may cause
long-term adverse effects in the aquatic
environment.

S-phrase(s) : S28 After contact with skin, wash immediately

with plenty of soap and water.
S37/39 Wear suitable gloves and eye/face
protection.
S61 Avoid release to the environment. Refer to
special instructions/safety data sheets.

Exceptional labelling of : Contains epoxy constituents. See information supplied by the

special preparations manufacturer.

Hazardous components : butanedioldiglycidyl ether

which must be listed on the EC-No.: 219-371-7
label
reaction product: bisphenol A-(epichlorhydrin); epoxy resin
(number average molecular weight < 700)

6/7
SAFETY DATA SHEET
according to applicable EC directive

Ident-No: ARALDITE LY 564

Version 1 Print Date 07.04.2009
Revision Date 22.03.2009

National legislation

Notification status

: EINECS yes

: TSCA yes

16. OTHER INFORMATION

List of R-phrases (Section 3)

R20/21 Harmful by inhalation and in contact with skin.

R36/38 Irritating to eyes and skin.
R43 May cause sensitization by skin contact.
R51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the
aquatic environment.
R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the
aquatic environment.

The provision of Safety Data Sheets comes under Regulation 6 of CHIP (CHIP is the recognised
abbreviation for the Chemicals Hazard Information and Packaging Regulations). This is an addition
to the Health and Safety at Work Act 1974.Users of products supplied by Huntsman Advanced
Materials should take appropriate measures to ensure working practices are in accordance with the
Control of Substances Hazardous to Health Regulations (COSHH).
All information is based on results gained from experience and tests and is believed to be accurate
but is given without acceptance of liability for loss or damage attributable to reliance thereon as
conditions of use lie outside our control. Users should always carry out sufficient tests to establish
the suitability of any products for their intended applications. No statements shall be incorporated in
any contract unless expressly agreed in writing nor construed as recommending the use of any
product in conflict of any patent. All goods are supplied subject to Huntsman Advanced Materials
General Conditions of Sale.

7/7