REVISED OCTOBER 2015

MEGAPOXY PM
GAP FILLING EPOXY PASTE ADHESIVE FOR CIVIL ENGINEERING USE
DESCRIPTION  EGAPOXY PM is specially formulated non-sag epoxy filling paste and adhesive. This easy
M
to use two-part epoxy product sets after mixing with excellent properties ideally suited for the
following applications.

USES BONDING FILLING AND REPAIR

• Precast concrete articles • Concrete Pipes and Tanks
• Grouting bolts • Fibreglass articles
• Natural stones • Concrete floors and stairs
• Bricks and ceramics • Concrete columns
• Metals • Insitu formed concrete

ADVANTAGES • Simple 1: 1 mix ratio

• Creamy texture, blends easily
• Non sag on vertical surfaces
• Rapid setting
• Adheres and cures under adverse conditions (cold and damp)
• Good strength VIVACITY ENGINEERING
retention after prolongedPTY LTD
immersion in water
3 Sefton Road,and
• Tensile Thornleigh, NSW 2120
compressive | PO Box
strength 71, Hornsby,
superior NSW Australia 1630
to concrete
• Very61good
Phone: 3044 | resistance
chemical
(2) 9875 Fax: 61 (2) 9875 3665 | Email: [email protected]
www.megapoxy.com | ABN 78 305 545 664
PRODUCT
PART “A” PART “B”
SPECIFICATION
CONSISTENCY: Thixotropic paste Thixotropic paste
COLOUR: White Black or Neutral
FLASH POINT: Above 100°C Above 100°C

SURFACE METALS:
PREPARATION Should be grit blasted to clean surface.
Mechanically abraded and degreased.
Wire brushing is not entirely satisfactory and gives minimal adhesion only.

PAINTED SURFACES:
A proprietary brand paint stripper should be used.
Concrete - the surface may be either flame cleaned or mechanically abraded.

PROCESSING DATA MIXING RATIO: 1 part resin to 1 part hardener by volume

MIXING: Mix until uniform grey or white
WORKING LIFE AT 25°C: 45 minutes
MINIMUM APPLICATION 10°C
TEMPERATURE:
MINIMUM CURE TIME: 12 hours at 25°C
FULL CURE TIME: 4 days at 25°C
wrightcreative.com.au 0316

Issue 3, Page 1 of 2, 2016-02-17, Megapoxy PF

PAGE 1
VIVACITY ENGINEERING PTY LTD
3 Sefton Road, Thornleigh, NSW 2120 | PO Box 71, Hornsby, NSW Australia 1630
Phone: 61 (2) 9875 3044 | Fax: 61 (2) 9875 3665 | Email: [email protected]
www.megapoxy.com | ABN 78 305 545 664
 REVISED OCTOBER 2015

IMPORTANT It is essential that the correct mixing ratio be used and that the Part “A” and Part “B” are
INFORMATION t horoughly mixed together before use. Inaccuracies and poor mixing will result in lower
physical properties of the cured system and, if the error is sufficiently large, the system
may not cure satisfactorily and discolour on ageing.

CURED PROPERTIES MAXIMUM OPERATING 70°C

(TYPICAL) TEMPERATURE:
DENSITY: 1.45 kg per litre

TENSILE STRENGTH: 25 MPA

TENSILE BOND STRENGTH: 10 MPA

COMPRESSIVE STRENGTH: 80 MPA

FLEXURAL STRENGTH: 15 MPA

VIVACITY ENGINEERING PTY LTD
3 Sefton Road, Thornleigh,
COEFFICIENT NSW 2120 | PO60
OF LINEAR BoxMM/MM/°C
71, Hornsby, NSW Australia 1630
X 10-6
EXPANSION:
Phone: 61 (2) 9875 3044 | Fax: 61 (2) 9875 3665 | Email: [email protected]
Properly mixed www.megapoxy.com
Megapoxy PM will | ABN
not 78 305or545
stain 664
discolour white or light coloured marble
and ceramics.

AVAILABILITY  EGAPOXY PM is available in 4 litre & 20 litre kits. Shelf life of unopened kits is 2 years
M
minimum. Product should be stored in cool dry store.

CLEANING Uncured Megapoxy PM can be removed with Megapoxy Thinners.

PRECAUTIONS  void prolonged contact with skin. Wash affected areas with soap and warm water.
A
For further information refer to Bulletin No.100 and Safety Data Sheet for Megapoxy PM.

wrightcreative.com.au 0316

Issue 3, Page 2 of 2, 2016-02-17, Megapoxy PF

PAGE 2
VIVACITY ENGINEERING PTY LTD
3 Sefton Road, Thornleigh, NSW 2120 | PO Box 71, Hornsby, NSW Australia 1630
Phone: 61 (2) 9875 3044 | Fax: 61 (2) 9875 3665 | Email: [email protected]
www.megapoxy.com | ABN 78 305 545 664