Product Bulletin Fisher HP Series Control Valves en 123584

Product Bulletin
HP Valve 51.2:HP
D101635X012 December 2020
Fisher™ HP Series Control Valves

HP (Globe Valve)
HPA (Angle Valve)
n Balanced High-Temperature Trim
n Balanced Tight Shutoff Trim
n Unbalanced Trim
Fisher HP Series control valves are single-port,

high-pressure, globe- or angle-style valves with metal
seats, cage guides, and push-down-to-close valve plug
action.
These valves are designed for high-pressure

applications in process control industries such as
power generation, hydrocarbon production, chemical
processing, and refining.
HP Series valves have NACE compliant materials

available. In certain sizes extra valve body wall X0183-2
thickness provides a safety margin of protection
FISHER HP VALVE WITH 667 ACTUATOR AND
against erosion, as well as extra protection against FIELDVUE™ DVC6200 DIGITAL VALVE CONTROLLER
corrosion due to chemical attack. Because these valves
feature a thicker valve body wall, they are available in
higher intermediate ratings with weld-end fittings.
Unless otherwise noted, all NACE references are to

NACE MR0175-2002 and MR0103.
Balanced Tight
Shutoff Trim
Balanced HPT and HPAT

These valves use a balanced valve plug and offer
High-Temperature Trim excellent shutoff with process temperatures below
232_C (450_F). The temperature limits of HPT can be
extended above 232_C (450_F) to 316_C (600_F) by
HPD and HPAD using PEEK (PolyEtherEtherKetone) anti-extrusion rings
in combination with a spring-loaded PTFE seal. The
These valves use a balanced valve plug with graphite PEEK anti-extrusion rings expand to help close off the
piston rings and are well suited for general applications clearance gaps on the plug outside diameter and the
with process temperatures in excess of 232_C (450_F), cage inside diameter where the PTFE seal may extrude
where extremely tight shutoff is not required. at high temperatures and pressures.
www.Fisher.com
Product Bulletin
51.2:HP HP Valve
December 2020 D101635X012
Specifications
Available Configurations(1) and Valve Sizes temperature service
See table 1 Valve Plug, Cage, and Seat Ring: See table 13
Other Parts: See table 7
Common Characteristics: Designed according to:
J ASME B16.34 Valve-Flanges, Threaded and Welded Consult your Emerson sales office for special trim and
End and J ANSI/ISA-75.08.05 (long or short) or valve body material availability.
ANSI/ISA-75.08.06 (long or short) J Socket Welding
consistent with ASME B16.11 J ASME B16.10 Material Temperature Capabilities(1)
Face-to-Face and End-to-End dimensions of valves HPD, HPAD, HPS, and HPAS: Up to 593_C (1100_F)
unless limited (see tables 7 and 13 and figure 17)
End Connections Styles(1) HPT and HPAT: Up to 316_C (600_F) unless limited
See table 1 (see tables 7 and 13 and figure 17)
Maximum Inlet Pressure and Temperature(1,2) Flow Characteristics(4)

Flanged, Socketweld, or Buttweld: Consistent with Standard Cages: J Linear, J equal percentage,
CL900, 1500, 2500, and 3200 according to ASME J modified equal percentage(5)
B16.34, unless limited by maximum pressure drop or Cavitrol III, Whisper Trim III, and WhisperFlo Cages:
material temperature capabilities Linear
Micro-Flute: Equal percentage
In addition, both steel HP and HPA valves with BWE Micro-Flat: Linear
and SWE connections have increased Micro-Form: J Equal percentage, J modified equal
pressure/temperature ratings as shown in table 3 percentage
Maximum Pressure Drop(1) Flow Direction
Valve with Standard Cage: See figure 17 Standard Cage
Valve with Cavitrol™ III Cage: Typically 149 bar (2160 J HPD, HPAD: Normally flow down
psi) for two-stage and 207 bar (3000 psi) for J HPS, HPAS: Normally flow up(6)
three-stage cage. Consult Fisher Bulletin 80.2:030, J HPAS Micro-Flat: Flow down
Cavitrol III One-, Two-, and Three-Stage trims J HPS, HPAS Micro-Form: Flow up only
(D100196X012) for more information J HPT, HPAT: Normally flow down
Valve with Whisper Trim™ III Cage: Cavitrol III Cage: Flow down
0.999 nP/P1 maximum for levels A1 through D3 Whisper Trim III and WhisperFlo Cage: Flow up
Valve with WhisperFlo™ Trim:
Levels X, Y, and Z: 0.999 nP/P1 maximum Flow Coefficients
See table 2 and also Fisher Catalog 12
Shutoff Classifications
See table 4 Noise Levels
See Fisher Catalog 12, Section 3 for noise prediction
Construction Materials methods
Valve Body and Bonnet:
J WCC steel(3), J WC9 Cr-Mo steel(3)(9), J C12A Port Diameters, Valve Plug Travel, and
chrome-moly alloy, J CF8M, CF8C, CD3MN, and Stem Diameters
CD3MWCuN stainless steel, and J LCC for low See tables 5, 9, 10, and 12
- continued -
2
Product Bulletin
HP Valve 51.2:HP
Specifications (continued)
Bonnet Style and Mounting(1) Approximate Weight
J Standard Bonnet: See figure 1 See table 6
Yoke Temperature Limit (NPS 2 through 6): Standard
bonnet with cast iron yoke is limited to 538_C Optional Safety Instrumented System Classification
(1000_F) HPD, HPS, HPAS, and HPT: SIL3 capable for NPS 1
J Optional Style 1—Extension Bonnet: Used for NPS through 14 - certified by exida Consulting LLC
1 and 2 valves for CL900 or 1500, and NPS 1 valves for HPAD and HPAT: SIL3 capable for NPS 1, 2, 6, 8, and
CL2500 (see figures 22 and 23) 12 - certified by exida Consulting LLC
Packing Arrangements Options(1)
J Single, J Double, and J Leakoff standard J Valves with weld-end fittings have increased
packing, or optional J ENVIRO-SEAL™ and pressure/temperature ratings, called intermediate
J HIGH-SEAL packing systems. See figure 7. Also see ratings(7), J Class V(6) shutoff for HPT and HPAT to
Fisher bulletin 59.1:061, ENVIRO-SEAL and 316_C (600_F) using PEEK anti-extrusion rings(8), J
HIGH-SEAL Packing System for Sliding-Stem Valves Class V shutoff for HPD and HPAD to 593_C (1100_F)
(D101633X012) using C-seal trim, J expanded ends(7) for NPS 4 and
6 valves (NPS 4 valves are available with NPS 6 ends,
Yoke Boss Diameter for Actuator Mounting and NPS 6 valves are available with NPS 8 ends), J
See tables 5 and 11, and figures 21, 22, and 23 lubricator or lubricator/isolating valve(7)
1. The pressure/temperature limits in this bulletin and any applicable standard limitations should not be exceeded.
2. EN (or other valve body material) ratings and end connections can usually be supplied; consult your Emerson sales office.
3. SA-105 and SA-182-F22 are used for CL2500 HPA valves instead of WCC and WC9.
4. Special characterized cages are available. Contact your Emerson sales office.
5. Modified equal percentage characteristic is equal percentage for the first 75% of travel, then opens quickly for additional capacity.
6. HPS valves may be used flow down for on-off service only. HPAS valves may be used for flow down in erosive service.
7. For more information contact your Emerson sales office.
8. Required for all boiler feedwater applications.
9. For NPS 8, 10, and 12 above 510_C (950_F) when using WC9 body must use C12A bonnet. Below 510_C (950_F) when using WC9 body can use WC9 bonnet.
Table of Contents
Balanced High-Temperature Trim . . . . . . . . . . . . . . . . 1 Material Selection Guidelines . . . . . . . . . . . . . . . . . . 10
Balanced Tight Shutoff Trim . . . . . . . . . . . . . . . . . . . . 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Unbalanced Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Trim Selection Guidelines . . . . . . . . . . . . . . . . . . . . . 28
Expanded Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Trim Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cavitrol, Whisper Trim Pressure/Temperature Limits for
and WhisperFlo Cages . . . . . . . . . . . . . . . . . . . . . . . 4 Trim Material Combinations . . . . . . . . . . . . . . . . . 37
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3
Product Bulletin
51.2:HP HP Valve
Figure 1. Fisher HPD Valve Assembly, NPS 2 to 6 Unbalanced Trim

HPS and HPAS
These valves have an unbalanced plug and provide
excellent shutoff.
Expanded Ends
Expanded ends are available on the NPS 4 and 6 CL900
and 1500 HP (ISA 75.08.05 (long) or ISA 75.08.06
(long)) valves. The NPS 4 HP valve body is offered with
FLOW NPS 6 ends. The NPS 6 valve body is offered with NPS 8
ends. Both flanged and buttweld end valve bodies are
offered with expanded ends.
W5815A-1
Figure 2. Fisher HPD Valve Assembly, NPS 8 to 14

Cavitrol III, Whisper Trim
III, and WhisperFlo Cages
To eliminate cavitation damage in a properly-sized
valve, a Cavitrol III cage is available with HPS, HPAS,
HPT, HPAT, and HPD control valves.
To help attenuate aerodynamic noise in gaseous

service, Whisper Trim III and WhisperFlo (figure 3)
cages are available with HPS, HPAS, HPT, HPAT, along
with NPS 8 through 14 HPD and HPT control valves.
Contact your Emerson sales office for more
information.
FLOW
X1514
Features
n Valve Plug Stability— Rugged cage guiding provides
increased valve plug stability, which reduces
vibration and mechanical noise.
Figure 3. Typical WhisperFlo Trim Cut Section View
for Fisher HP Valve n Full Pressure Drop Capability—Rugged construction
FLOW OUT allows full pressure drop capability in HP series
valves.
n Spiral-Wound Gaskets for Excellent Sealing Under

All Service Conditions—Premium materials are used
in the construction of spiral-wound gaskets for HP
Series valves. These premium materials, which
FLOW IN make up the standard spiral-wound gaskets, are
W7065
N06600 (alloy 600)/graphite or N07750
(alloy X750)/graphite.
4
Product Bulletin
HP Valve 51.2:HP
n Piping Economy—The availability of expanded end

Figure 4. Fisher HPT Valve Assembly, NPS 3 to 6
connections on NPS 4 and 6 HP (ISA 75.08.05 (long)
or ISA 75.08.06 (long)) valves may eliminate the
need for line swages while accommodating
oversized piping arrangements.
n Quick Change Trim—Maintenance is simple and can

easily be performed using common tools. Trim
components can be quickly removed and changed
with no need for special tools.
n Integrated Cage-Seat Ring Design—Find this option

on globe NPS 8, 10, 12, 14 and angle NPS 12 valves
offering easier maintenance and better shutoff.
FLOW
n Standard Hard Trim Materials—The cage, valve plug,

and other trim parts are manufactured from
hardened materials. This standard feature provides
excellent wear resistance.
n Increased Pressure/Temperature Ratings— HP Series

Figure 5. Fisher HPAT Valve Assembly, NPS 6 to 12 valves with weld-end fittings have increased
pressure/temperature ratings, called intermediate
ratings, as defined in ASME B16.34. The extra
strength of these valves allows ratings higher than
the standard CL900 or 1500 ratings specified in
B16.34. The globe NPS 8 to 12 HP is available as a
standard Intermediate ANSI Class 3200 to achieve
higher pressure/temperature ratings. Not available
on angle NPS 8. Contact your Emerson sales office
for further information on intermediate ratings.
FLOW
n Trim Interchangeability—Cavitrol III, Whisper Trim

III, and WhisperFlo trims (figures 12, 13, and 15) are
interchangeable with standard trims.
n Control of Low Flow Rates/Tight

Shutoff—Micro-Flute and Micro-Form valve plugs
(figures 10 and 11, respectively) provide superb
rangeability in high-pressure, low-flow applications,
while maintaining tight shutoff (table 4). A choice of
several restricted port diameters helps to match
valve body capacity to required flow, to provide
necessary control with full travel, and to prevent
throttling near the seat.
Features (cont.) In low-flow applications where cavitation damage

may occur, the Micro-Flat valve plug can be used
n Compliance with the Clean Air Act—Optional with a special Cavitrol III cage. Contact your
ENVIRO-SEAL packing systems (figure 7) provide an Emerson sales office for more information.
improved stem seal to help prevent the loss of
valuable process fluid or emission of hazardous n Smooth Control at High Pressure Drops—Available
process fluid. The ENVIRO-SEAL packing systems on NPS 2 through 14 valves, balanced trim provides
feature PTFE or graphite ULF. smooth control at high pressure drops.
5
Product Bulletin
51.2:HP HP Valve
Features (cont.) NPS 8 through 12 HPD valves.
n High-Temperature Capability with Class V n Sour Service Trims Available—Long-lasting, erosion-

Shutoff—Use of C-seal trim (see figure 8) permits and corrosion-resistant trims are available for
Class V shutoff up to 593_C (1100_F) for NPS 2 control of sour service. These trims are offered with
through 6 HPD (ISA 75.08.05 (long) or ISA 75.08.06 either a standard cage, a Cavitrol III cage, a Whisper
(long)) valves. Use of Bore-seal trim (see figure 6) Trim III cage, or WhisperFlo trim. Spiral-wound
permits Class V shutoff up to 593_C (1100_F) for gasket construction is standard.
Table 1. Available Constructions

VALVE BODY MATERIAL AND END CONNECTION STYLE(1, 2)
WCC, WC9, LCC, C12A, CF8M, CF8C, CD3MN, SA-105, SA-182-F22, SA-182-F316, S31803
VALVE SIZE, and CD3MWCuN Stainless Steel F51, and S32760 F55 forged SST (for forged
DESIGN PRESSURE RATING
NPS Cast Valves steel HPA CL2500 angle valves)
RF or RTJ Flanged,
Socketweld
Buttweld, and Socketweld(3)
2 to 8 CL900 and 1500 X ---
HPAD
2, 6, 8, 12 CL2500 X X
CL900 and 1500 X ---
HPAS 1 to 2
CL2500 --- X
2 to 8 CL900 and 1500 X ---
HPAT
2, 6, 8, 12 CL2500 X X
2 to 6 CL900 and 1500 X ---
2, 3, 4, 6 CL2500 X ---
CL900,1500,
HPD X ---
8 to 12 and 2500
CL3200 X(4) ---
14 CL2500 X(4) ---
1 to 3 CL900 and 1500 X ---
HPS
1 to 4 CL2500 X ---
2 to 6 CL900 and 1500 X ---
2, 3, 4, 6 CL2500 X ---
CL900,1500,
HPT X ---
8 to 12 and 2500
CL3200 X(4) ---
14 CL2500 X(4) ---
X = Available Construction.
1. End connection style abbreviations: RF - Raised Face, RTJ - Ring Type Joint.
2. EN (or other valve body material) ratings and end connections can usually be supplied; consult your Emerson sales office.
3. Socketweld available on NPS 1, 1-1/2, and 2 only.
4. Only buttweld end available.
6
Product Bulletin
HP Valve 51.2:HP
Table 2. Typical Flow Coefficients(1)

DESIGN AND CLASS VALVE SIZE, NPS CHARACTERISTIC MAXIMUM Cv
M-Form Modified Equal Percentage
1 17.1
(HPS)
HP CL1500
2 Linear (HPS) 54.6
3 Linear (HPS) 127
Linear
4 212
Modified Equal Percentage
Linear 469
6
Modified Equal Percentage 412
Equal Percentage 449
HP CL900 and CL1500 8
Linear 767
10
Linear 973
12
Linear 1337
1 13.8
(HPS)
2 Linear (HPS) 40.9
Linear 87
3
HP CL2500 Modified Equal Percentage 84
Linear 153
4
Linear 324
6
8
Linear 560
HP CL2500 and CL3200 10
Linear 682
12
Linear 1232
HP CL2500 14
Linear 1525
1 19.5
(HPAS)
2 Linear (HPAS) 73.6
HPA CL1500 3 Linear 64.3
4 Linear 121
6 Modified Equal Percentage 203
8 Linear 425
1 14.3
(HPAS)
2 Linear (HPAS) 56.2
Linear 217
6
HPA CL2500 Modified Equal Percentage 203
Linear 446
8
Linear 1023
12
1. See Catalog 12 for a complete listing of flow coefficients.
7
Product Bulletin
51.2:HP HP Valve
Table 3. Increased Pressure/Temperature Ratings for Steel Valves with BWE and SWE Connections(1)
Intermediate Rating
Valve Type Valve Size, NPS Pressure Rating
(ASME B16.34)
CL900
1675
1 CL1500
CL2500 2800
CL900
2 1694
CL1500
Globe Valves 3 CL1500 1578
4 (long)(2) CL1500 2017
6 (long)(2) CL1500 1876
8 CL3200 3200
10 CL3200 3200
12 CL3200 3200
1. Contact your Emerson sales office for further information on intermediate ratings.
2. (Long) indicates industry standard long face-to-face.
8
Product Bulletin
HP Valve 51.2:HP
Table 4. Shutoff Classifications per ANSI/FCI 70-2 and IEC 60534-4

Valve Design Port Diameter, mm (Inches) ANSI/FCI and IEC Leakage Class
57.15 (2.25) and smaller II
II - Standard
58.7 (2.3125) to 105.9 (4.17)
HPD, HPAD III - Optional
III - Standard
111.1 (4.375) and larger
IV - Optional
Valve Size, NPS
Port Diameter, mm (Inches) Cage Style ANSI/FCI and IEC Leakage Class
HPD HPAD
Eq. %, Mod. Eq. %,
3 4 73 (2.875) Linear (std. cage), V - Standard
Linear (Whisper III, A1, B1) to 593_C (1100_F)
73 (2.875) Linear (Whisper III, D3) (for port diameters from 73 mm
HPD, HPAD [2.875 inch] through 136.5 mm [5.375
w/ C-seal trim Eq. %, Mod. Eq. %,
4 6 inch]
92.1 (3.625) Linear (std. cage),
with optional C-seal trim)
Linear (Whisper III, A1, B3, C3)
111.1 (4.375) Linear (Whisper III, D3) IV - Optional
Eq. %, Mod. Eq. %, (for port diameters 73 mm [2.875
6 8
136.5 (5.375) Linear (std. cage), inch] through 136.5 mm [5.375 inch]
Linear (Whisper III, A1, B3, C3)
Valve Size, NPS Port Diameter,
Cage Style ANSI/FCI and IEC Leakage Class
HPD HPAD mm (Inches)
139.7 (5.5)
8 ---
152.4 (6)
HPD(2), HPAD(2) 165.1 (6.5) V - Standard
10 --- to 593_C (1100_F)
w/ Bore-seal trim 177.8 (7) Eq. %, Linear (std. cage),
(for port diameters from 139.7 mm
165.1 (6.5) Whisper III, Cavitrol III
[5.5 inch] through 215.9 mm
12 12 190.5 (7.5) [8.5 inch] with optional Bore-seal trim)
203.2 (8)
14 --- 215.9 (8.5)
Cavitrol III and Micro-Flat V - Standard
HPS, HPAS, HPT, HPAT All Micro-Form, Micro-Flute, Eq. %, IV - Standard
Mod Eq. %, Linear, Whisper III V - Optional
TSO - Optional
TSO is not an ANSI/FCI or IEC leakage
class.
Valves with TSO trim are factory tested
to a more stringent Fisher test
HPS and HPT w/ TSO
See table 5 See table 5 requirement of no leakage at time of
(Tight Shutoff trim)
shipment.
Test medium is water.
Specify service ΔP when ordering.
Test procedure is ANSI/FCI Class V test
procedure B
V - Standard (to 316_C [600_F])
HPT and HPAT w/ PEEK(1) Anti-Extrusion IV - Optional (47.6 mm [1.875 inch]
47.6 (1.875) to 215.9 (8.5) All
Rings through
203.2 mm [8 inch] ports)
1. PEEK (PolyEtherEtherKetone), required for all boiler feedwater applications.
2. Trims 263, 2635, 264, 2645, 265, and 2655 are not available in bore-seal.
9
Product Bulletin
51.2:HP HP Valve
Material Selection pressure drop limits of the valve body-trim

combinations selected.
Guidelines
Use the following steps as a guideline for the selection
of materials:
1. Determine the pressure/temperature rating of the

Installation
valve body size and material required. Inlet pressure The valve must be installed so flow through the valve is
and temperature must always be limited by the as indicated by the flow direction arrow on the valve
applicable ASME pressure/temperature rating. body. Consideration should be given to installing an
upstream strainer, especially if the valve uses a Cavitrol
2. Select the desired trim style from the Available III cage, Whisper Trim III, or WhisperFlo trim.
Configurations specification and from table 4, Shutoff
Classifications. Overall dimensions are shown in figures 21, 22, and
23. Face-to-face dimensions are in compliance with
3. Select desired materials from tables 7, 9, 12, and 13 ANSI/ISA-75.08.05 (long or short), ANSI/ISA-75.08.06
and figure 17. The temperature capabilities (long or short), or ASME B16.10. Actual end
determined from figure 17 may be further limited by connection dimensions conform to ASME B16.25 for
the temperature capabilities of materials selected buttweld ends, to B16.11 for socket welding, and to
from tables 7 and 13. Refer to figure 17 to determine ASME B16.5 for flanged ends.
10
Product Bulletin
HP Valve 51.2:HP
Table 5. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) Trim
PORT DIAMETER CV UNBALANCE
VALVE MAX TRAVEL YOKE BOSS SIZE REDUCTION
TRIM Nominal Actual TSO AREA
TYPE AT 100%
mm Inch mm Inch mm Inch mm Inch TRAVEL(1) Inch2
Balanced Plugs—Flow Down Only
HPT
CAV III 3-Stage 63.5 2.5 90 3-9/16 47.6 1.875 42.9 1.6875 5% 0.031
NPS 3(2)
HPT
90 3-9/16
NPS 4 CAV III 3-Stage 76.2 3 73.0 2.875 68.3 2.6875 2% 0.047
127 5
(long)(3)
90 3-9/16
HPT CAV III 3-Stage 102 4 116 4.5625 111 4.375 0% 0.080
127 5
NPS 6
90 3-9/16
(long)(3) Standard 76.2 3 137 5.375 132 5.1875 4% 0.206
127 5
Unbalanced Plugs—Flow Down Only
HPS
CAV III 3-Stage 50.8 2 90 3-9/16 25.4 1 26.2 0.8125 0% 0.785
NPS 2
1. This column lists the percent reduction of published maximum CV of the trim listed in the TRIM column.
2. Not available with 5-inch yoke boss.
Figure 6. Typical Balanced TSO Trim
VALVE PLUG
SEAL
TSO PROTECTED
SOFT SEAT SEAL
W7020-1
11
Product Bulletin
51.2:HP HP Valve
Figure 7. ENVIRO-SEAL and HIGH-SEAL Packing Systems
PACKING
BOX PACKING
STUD BOX
STUD
SPRING
SPRINGS
FOLLOWER
PACKING FOLLOWER
PACKING
W8533-1
TYPICAL HIGH-SEAL PACKING SYSTEM W8532-1
WITH GRAPHITE ULF PACKING TYPICAL ENVIRO-SEAL PACKING SYSTEM

WITH GRAPHITE ULF PACKING
PACKING
BOX
STUDS
SPRINGS
ANTI-
EXTRUSION
RING PACKING
RING
LANTERN VALVE
RING BONNET
W5803-3
TYPICAL ENVIRO-SEAL PACKING SYSTEM

WITH PTFE PACKING
12
Product Bulletin
HP Valve 51.2:HP
Table 6. Approximate Weights (Valve and Bonnet Assemblies)

VALVE SIZE, KILOGRAMS POUNDS
VALVE TYPE PRESSURE RATING
NPS Flg SWE, BWE Flg SWE, BWE
CL900 and 1500 42 38 93 85
1
CL2500 45 34 100 76
1-1/2 x 2 CL2500 --- 34 --- 76
CL900 and 1500 72 52 158 115
2
CL2500 104 74 229 164
CL900 125 --- 276 ---
3 CL1500 129 97 284 213
CL2500 228 163 502 358
CL900 230 --- 507 ---
4 (long)(2)
CL1500 249 201 548 444
CL900 167 136 368 ---
4 (short)(2) CL1500 194 162 428 444
CL2500 321 206 708 444
CL900 511 --- 1127 ---
6 (long)(2)
CL1500 557 455 1228 1003
Globe Valves CL900 317 227 699 500
6 (short)(2) CL1500 575 269 1268 593
CL2500 757 481 1669 1060
CL900 720 510 1587 1124
CL1500 930 640 2050 1411
8
CL2500 1630 1050 3594 2315
CL3200 --- 1460 --- 3219
CL900 1030 750 2271 1653
10 CL1500 1490 1010 3285 2227
CL2500 2560 1550 5644 3417
CL3200 --- 2200 --- 4850
CL900 1340 940 2954 2072
CL1500 1950 1250 4299 2756
12
CL2500 3380 2000 7452 4409
CL3200 --- 2950 --- 6504
14 CL2500 --- 2297 --- 5064
CL900 and 1500 40 36 88 80
1
CL2500 --- 72(1) --- 160(1)
CL900 and 1500 69 50 153 110
2
CL2500 --- 109(1) --- 240(1)
3 CL1500 123 78 272 173
Angle Valves 4 CL1500 181 117 399 258
CL1500 357 202 788 445
6
CL2500 658 325 1451 716
CL1500 648 405 1428 893
8
CL2500 971 663 2141 1462
12 CL2500 2471 1660 5448 3660
1. Only SWE is available for CL2500.
2. (Long) indicates industry standard long face-to-face. (Short) indicates industry standard short face-to-face.
13
Product Bulletin
51.2:HP HP Valve
Figure 8. C-seal Trim
C-SEAL C-SEAL
METAL METAL
PLUG PLUG
SEAL(1) SEAL(1)
FLOW DOWN FLOW UP
VIEW A
37B1399-A
NOTE:
1. Reverse the orientation of the C-seal plug seal for proper shutoff when valve is used in a process with different fluid flow direction.
Figure 9. Bore Seal Trim
WINDOW,
LINEAR
PISTON
RING
BACKUP
RING
BORE
SEAL
VIEW A, VIEW A,
BORE SEAL, BORE SEAL,
FLOW DOWN FLOW UP
14
Product Bulletin
HP Valve 51.2:HP
Table 7. Construction Materials and Temperature Capabilities for Parts Other than Valve Body
TEMPERATURE CAPABILITIES
PART MATERIAL
_C _F
Valve plug, cage, and seat ring See table 13 See table 13
S20910 -198 to 593 -325 to 1100
Valve plug stem S42200 -29 to 649 -20 to 1200
S32760 -51 to 316 -60 to 600
-46 to 427 (to 482 -50 to 800 (to 900
Graphite (FMS 17F27)
HPD for nonoxidizing service) for nonoxidizing service)
piston ring -46 to 538 (to 593 -50 to 1000 (to 1100
Graphite (FMS 17F39)(2)
for nonoxidizing service) for nonoxidizing service)
S41600 (416 SST) -29 to 427 -20 to 800
Backup ring
S31600 (316 SST) -198 to 593 -325 to 1100
S30200 (302 SST)
Spring-loaded Retaining ring -254 to 593 -425 to 1100
N07750 (NACE)
HPT or HPAT
PTFE with N10276 Spring -73 to 232(1) -100 to 450(1)
valve plug seal Seal ring
PTFE with R30003 Spring(3) -73 to 316 -100 to 600
Anti-extrusion
PEEK (PolyEtherEtherKetone) -73 to 316 -100 to 600
rings
Cage gasket N06600/Graphite -240 to 593 -400 to 1100
TSO protected soft seat seal Carbon-filled PTFE -73 to 232 -100 to 450
N06600/Graphite -240 to 593 -400 to 1100
Seat ring gasket
S31600/Graphite -240 to 593 -400 to 1100
PTFE V-ring -46 to 232 -50 to 450
Graphite ribbon filament (oxidizing service to 371_C [700_F]) -254 to 538 -425 to 1000
Packing
Graphite ribbon
371 to 593 700 to 1100
(high-temperature oxidizing service)
Packing follower,
S31600 stainless steel -254 to 593 -425 to 1100
spring, or lantern ring
Packing box ring S31600 stainless steel -254 to 593 -425 to 1100
Steel -29 to 427 -20 to 800
Packing flange, studs, or nuts
S31600 stainless steel -198 to 593 -325 to 1100
1.If used with PEEK anti-extrusion rings, PTFE/carbon seal ring may be used in temperatures up to 316_C (600_F) for non-oxidizing service or up to 260_C (500_F) for oxidizing service.
2. NPS 8, 10, 12 HPD and HPT come standard with Graphite (FMS 17F39) piston ring.
3. Only offered in NPS 8, 10 and 12 HPT.
15
Product Bulletin
51.2:HP HP Valve
Table 8. Construction Materials and Temperature Capabilities for Valve Body-to-Bonnet Bolting
(Face-to-Face Structure)
LONG SHORT
VALVE VALVE TEMPERATURE VALVE TEMPERATURE
STUDS / NUTS VALVE VALVE
TYPE BODY CAPABILITIES BODY CAPABILITIES
SIZE, NPS SIZE, NPS
MATERIAL _C _F MATERIAL _C _F
WCC and WCC and
Steel SA193-B7 NCF2 1 to 6 -29 to 427 -20 to 800 3 to 14 -29 to 427 -20 to 800
WC9 WC9
(all valve body materials)
LCC 1 to 6 -46 to 343 -50 to 650 LCC 3 to14 -46 to 343 -50 to 650
Steel SA194-2H NCF2
(all valve body materials) CF8M and
CF8M 1 to 6 -48 to 427(2) -55 to 800(2) 3 to14 -29 to 316 -20 to 600
CF8C
WCC and
Steel SA193-B7M NCF2 WCC 1 to 6 -29 to 427 -20 to 800 3 to 14 -29 to 427 -20 to 800
WC9
for sour service(3)
Steel SA194-2HM NCF2
for sour service CF8M and
CF8M 1 to 6 -29 to 427 -20 to 800 3 to 14 -29 to 260 -20 to 500
CF8C
WC9 1 to 6 -29 to 538 -20 to 1000
WC9 3 to 14 -29 to 510 -20 to 950
Steel SA193-B16 C12A 1 to 6 -29 to 510 -20 to 950
Globe
Steel SA194-7 WCC 1 to 6 -29 to 427 -20 to 800 WCC 3 to 14 -29 to 427 -20 to 800
N07718 SST (SB637)(1) WC9 1 to 6 -29 to 566 -20 to 1050 WC9 3 to 14 -29 to 566 -20 to 1050
Steel SA194-7 C12A 1 to 6 -29 to 593 -20 to 1100 C12A 3 to 14 -29 to 593 -20 to 1100
S31600 stainless steel
SA193-B8M Class 2 CF8M 1 to 3 -198 to 427 -325 to 800 --- --- --- ---
S31600 stainless steel SA194-8M
S31600 Stainless steel
CF8M and
SA193-B8M2 Class 2B(3) --- --- --- --- 3 to 14 -198 to 566 -325 to 1050
CF8C
S31600 Stainless Steel SA194-8M
S20910 SST (SA479-XM-19)(1) CF8M and
CF8M 1 to 6 -198 to 538 -325 to 1000 3 to14 -198 to 566 -325 to 1050
Steel SA194-7 CF8C
WCC and WCC and
Steel SA193-B7 NCF2 1 to 8 -29 to 427 -20 to 800 6, 8, 12 -29 to 427 -20 to 800
WC9 WC9
(all valve body materials)
LCC 1 to 8 -46 to 343 -50 to 650 LCC 6, 8, 12 -46 to 343 -50 to 650
Steel SA194-2H NCF2
(all valve body materials) CF8M and
CF8M 1 to 8 -48 to 427 -55 to 800 6, 8, 12 -29 to 316 -20 to 600
CF8C
WCC and
Steel SA193-B7M NCF2 WCC 1 to 8 -29 to 427 -20 to 800 6, 8, 12 -29 to 427 -20 to 800
WC9
for sour service(3)
LCC 1 to 8 -46 to 343 -50 to 650 LCC 6, 8, 12 -46 to 343 -50 to 650
Steel SA194-2HM NCF2
for sour service CF8M and
CF8M 1 to 8 -48 to 427 -55 to 800 6, 8, 12 -46 to 260 -20 to 500
CF8C
WCC 1 to 8 -29 to 427 -20 to 800 WCC 6, 8, 12 -29 to 427 -20 to 800
Steel SA193-B16 WC9 1 to 8 -29 to 538 -20 to 1000
Angle WC9 6, 8, 12 -29 to 510 -20 to 950
Steel SA194-7 C12A 1 to 6 -29 to 510 -20 to 950
LCC 3 and 4 -46 to 343 -50 to 650 LCC 6, 8, 12 -46 to 343 -50 to 650
N07718 SST (SB637)(1) WC9 1 to 8 -29 to 566 -20 to 1050 WC9 6, 8, 12 -29 to 566 -20 to 1050
Steel SA194-7 C12A 1 to 8 -29 to 593 -20 to 1100 C12A 6, 8, 12 -29 to 593 -20 to 1100
S31600 stainless steel
SA193-B8M Class 2 CF8M 1 to 4 -29 to 427 -20 to 800 --- --- --- ---
S31600 stainless steel SA194-8M
S31600 Stainless Steel
CF8M and
SA193-B8M2 Class 2B(3) --- --- --- --- 6, 8, 12 -198 to 566 -325 to 1050
CF8C
S31600 Stainless Steel SA194-8M
S20910 SST (SA479-XM-19)(1) CF8M and
CF8M 1 to 4 -198 to 538 -325 to 1000 6, 8, 12 -198 to 566 -325 to 1050
Steel SA194-7 CF8C
1. These stud materials are not listed in ASME B16.34.
2. Steel studs and nuts with NCF (non-corroding finish) coating are used with NPS 4 and 6 CF8M valve bodies.
3. Short HP constructions are derated with this bolt material. Consult your Emerson sales office for information.
16
Product Bulletin
HP Valve 51.2:HP
Table 9. Additional Globe Valve Specifications CL900 through CL1500

VALVE PORT VALVE PLUG
VALVE BODY DESIGN VALVE STEM DIAMETER
SIZE, FLOW CHARACTERISTIC DIAMETER TRAVEL
AND PLUG STYLE
NPS mm Inches mm Inches mm Inches
6.4 0.25 19 0.75 12.7 1/2
HPS Micro-Flute Equal percentage 9.53 0.375 19 0.75 12.7 1/2
12.7 0.50 19 0.75 12.7 1/2
6.4 0.25 19 0.75 12.7 1/2
12.7 0.50 19 0.75 12.7 1/2
Equal percentage
19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
HPS Micro-Form 25.4 1 19 0.75 12.7, 19.1 1/2, 3/4
1
12.7 0.50 29 1.125 12.7 1/2
Modified equal percentage 19.1 0.75 29 1.125 12.7, 19.1 1/2, 3/4
25.4 1 29 1.125 12.7, 19.1 1/2, 3/4
22.2 0.875 19 0.75 12.7 1/2
HPS Micro-Flat 25.4 1 29 1.125 12.7 1/2
Linear (Cage Style: Cavitrol III, 2-stage)
25.4 1 38 1.5 12.7, 19.1 1/2, 3/4
HPS Standard 22.2 0.875 38 1.5 12.7, 19.1 1/2, 3/4
6.4 0.25 19 0.75 12.7 1/2
Equal percentage 12.7 0.50 19 0.75 12.7 1/2
19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
12.7 0.50 29 1.125 12.7, 19.1 1/2, 3/4
HPS Micro-Form
19.1 0.75 29 1.125 12.7, 19.1 1/2, 3/4
Modified equal percentage 25.4 1 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
31.8 1.25 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
38.1 1.5 38 1.5 19.1, 25.4 3/4, 1
Linear (Cage Style: Cavitrol III, 2-stage) 25.4 1 38 1.5 19.1 3/4
15.88 0.625 31.7 1.3 19.1 3/4
HPS Micro-Flat
Linear (Cage Style: Cavitrol III, 3-stage) 25.4 1 38 1.5 19.1 3/4
25.4 1 63.5 2.5 19.1 3/4
Equal percentage 47.6 1.875 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
Modified equal percentage 47.6 1.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
2 Linear (Cage Style: Standard) 47.6 1.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
HPS Standard
Linear
47.6 1.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
(Cage Style: Whisper Trim III, Level A1)
Linear (Cage Style: Cavitrol III, 3-stage) 25.4 1 51 2 19.1 3/4
Equal percentage 47.6 1.875 29 1.125 12.7, 19.1 1/2, 3/4
HPD Linear (Cage Style: Standard) 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Linear
47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Equal percentage 47.6 1.875 29 1.125 12.7, 19.1 1/2, 3/4
Linear (Cage Style: Standard) 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Linear
HPT 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Linear (Cage Style: Cavitrol III, 2-stage) 44.5 1.750 51 2 12.7, 19.1 1/2, 3/4
‐continued‐
17
Product Bulletin
51.2:HP HP Valve
Table 9. Additional Globe Valve Specifications CL900 through CL1500 (continued)

AND PLUG STYLE
Linear 73 2.875 51 2.0 19.1, 25.4 3/4, 1
HPS Modified equal percentage 73 2.875 51 2.0 19.1, 25.4 3/4, 1
Whisper III, Level A1, B1 73 2.875 50 2.0 19.1, 25.4 3/4, 1
Equal percentage 73 2.875 38 1.5 12.7, 19.1, 25.4 1/2,3/4,1
Modified equal percentage 73 2.875 51 2 12.7, 19.1, 25.4 1/2,3/4,1
Linear (Cage Style: Standard) 73 2.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
HPD Linear (Cage Style: Whisper Trim III,
73 2.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
Level A1, B1)
Linear (Cage Style: Whisper Trim III,
47.6 1.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
Level D3)
3 Equal percentage 73 2.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Modified equal percentage 73 2.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear (Cage Style: Standard) 73 2.875 51 2 12.7,19.1,25.4 1/2,3/4,1
73 2.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
Level A1, B1)
HPT Linear
47.6 1.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
(Cage Style: Whisper Trim III, Level D3)
Linear (Cage Style: Cavitrol III, 2-stage) 63.5 2.50 64 2.50 19.1, 25.4 3/4, 1
47.6 1.875 64 2.50 19.1, 25.4 3/4, 1
Linear (Cage Style: Cavitrol III, 3-stage) 42.86 1.688 64 2.50 19.1 3/4
47.6 1.875 88.9 3.50 19.1 3/4
Equal percentage 92.1 3.625 38 1.5 19.1, 25.4 3/4, 1
91.4 3.60 51 2 19.1, 25.4 3/4, 1
Modified equal percentage
92.1 3.625 51 2 19.1, 25.4 3/4, 1
91.4 3.60 51 2 19.1, 25.4 3/4, 1
Linear (Cage Style: Standard)
92.1 3.625 51 2 19.1, 25.4 3/4, 1
HPD Linear (Cage Style: Whisper Trim III,
92.4 3.60 51 2 19.1, 25.4 3/4, 1
Level A1, A3, B1, B3, C1, C3)
92.1 3.625 51 2 19.1, 25.4 3/4, 1
Level A1, B3, C3)
73 2.875 51 2 19.1, 25.4 3/4, 1
Level D3)
Equal percentage 92.1 3.625 38 1.5 19.1, 25.4 3/4, 1
91.4 3.60 51 2 19.1, 25.4 3/4, 1
4 92.1 3.625 51 2 19.1, 25.4 3/4, 1
91.4 3.60 51 2 19.1, 25.4 3/4, 1
92.1 3.625 51 2 19.1, 25.4 3/4, 1
92.4 3.60 51 2 19.1, 25.4 3/4, 1
Level A1, A3, B1, B3, C1, C3)
HPT 92.1 3.625 51 2 19.1, 25.4 3/4, 1
Level A1, B3, C3)
73 2.875 51 2 19.1, 25.4 3/4, 1
Level D3)
91.4 3.60 51 2 19.1, 25.4 3/4, 1
Linear (Cage Style: Cavitrol III, 2-stage) 72.39 2.85 76 3 25.4 1
87.3 3.4375 76 3 19.1, 25.4 3/4, 1
68.262 2.6875 76 3 19.1, 25.4 3/4, 1
Linear (Cage Style: Cavitrol III, 3-stage)
73 2.875 76 3 19.1, 25.4 3/4, 1
‐continued‐
18
Product Bulletin
HP Valve 51.2:HP

AND PLUG STYLE
Equal percentage 136.5 5.375 64 2.50 19.1, 25.4, 31.8 3/4, 1, 1-1/4
136.5 5.375 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Modified equal percentage(1)
137.2 5.400 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
136.5 5.375 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
137.2 5.400 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
136.6 5.375 76 3 25.4, 31.8 1, 1-1/4
Level A1, B3, C3)
137.2 5.40 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
6 HPD, HPT Level A1, A3, B1, B3, C1, C3)
Linear
111.1 4.375 76 3 25.4, 31.8 1, 1-1/4
(Cage Style: Whisper Trim III, Level D3)
Linear 118.36 4.66 102 4 31.8 1-1/4
(Cage Style: Cavitrol III, 2-stage) 133.35 5.25 102 4 19.1, 25.4, 31.8 3/4, 1, 1-1/4
(HPT only) 137.2 5.40 76 3 25.4, 31.8 1, 1-1/4
Linear 100.83 3.97 102 4 31.8 1-1/4
(Cage Style: Cavitrol III, 3-stage)
(HPT only) 115.9 4.5625 102 4 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Equal percentage 152.4 6.00 76.2 3 25.4, 31.8 1, 1-1/4
Linear (Cage Style: Standard) 152.4 6.00 76.2 3 25.4, 31.8 1, 1-1/4
152.4 6.00 101.6 4 25.4, 31.8 1, 1-1/4
Level A1, A3)
8 HPD, HPT
152.4 6.00 127 5 25.4, 31.8 1, 1-1/4
Level B1, B3, C1, C3, D3)
Linear (Cage Style: Cavitrol III, 2-stage) 152.4 6.00 127 5 25.4, 31.8 1, 1-1/4
Equal percentage 177.8 7.00 101.6 4 25.4, 31.8 1, 1-1/4
Linear (Cage Style: Standard) 177.8 7.00 101.6 4 25.4, 31.8 1, 1-1/4
177.8 7.00 101.6 4 25.4, 31.8 1, 1-1/4
Level A1, A3)
10 HPD, HPT
177.8 7.00 127 5 25.4, 31.8 1, 1-1/4
‐continued‐
19
Product Bulletin
51.2:HP HP Valve

AND PLUG STYLE
CL900 CL900
25.4, 31.8 1, 1-1/4
Equal percentage 203.2 8.00 101.6 4
CL1500 CL1500
25.4, 31.8, 50.8 1, 1-1/4, 2
CL900 CL900
25.4, 31.8 1, 1-1/4
Linear (Cage Style: Standard) 203.2 8.00 101.6 4
CL1500 CL1500
25.4, 31.8, 50.8 1, 1-1/4, 2
CL900 CL900
Linear (Cage Style: Whisper Trim III, 25.4,31.8 1, 1-1/4
203.2 8.00 127 5
Level A1, A3) CL1500 CL1500
25.4, 31.8, 50.8 1, 1-1/4, 2
12 HPD, HPT
CL900 CL900
Linear (Cage Style: Whisper Trim III, 25.4, 31.8 1, 1-1/4
203.2 8.00 152.4 6
Level B1, B3, C1, C3, D3) CL1500 CL1500
25.4, 31.8, 50.8 1, 1-1/4, 2
CL900 CL900
25.4, 31.8 1, 1-1/4
Linear (Cage Style: Cavitrol III, 2-stage) 203.2 8.00 152.4 6
CL1500 CL1500
25.4, 31.8, 50.8 1, 1-1/4, 2
CL900 CL900
25.4, 31.8 1, 1-1/4
Linear (Cage Style: Cavitrol III, 3-stage) 203.2 8.00 152.4 6
CL1500 CL1500
25.4, 31.8, 50.8 1, 1-1/4, 2
1. The first 75% is equal percentage.
20
Product Bulletin
HP Valve 51.2:HP
Table 10. Globe Valve Specifications for CL2500 through CL3200

AND PLUG STYLE
6.4 0.25 19 0.75 12.7 1/2
HPS Micro-Flute Equal percentage 9.525 0.375 19 0.75 12.7 1/2
12.7 0.50 19 0.75 12.7 1/2
6.4 0.25 19 0.75 12.7 1/2
Equal percentage 12.7 0.50 19 0.75 12.7 1/2
1
HPS Micro-Form 19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
19.1 0.75 29 1.125 12.7, 19.1 1/2, 3/4
25.4 1 29 1.125 12.7, 19.1 1/2, 3/4
Linear
HPS Micro-Flat 22.2 0.875 38 1.5 12.7, 19.1 1/2, 3/4
Linear
25.4 1 38 1.5 12.7, 19.1 1/2, 3/4
HPS Micro-Flute 15.875 0.625 31.8 1.25 19.1 3/4
Linear
1.5,
(Cage Style: Cavitrol III, 3-stage) 25.4 1 38.64 19.1 3/4
2.5
6.4 0.25 19 0.75
12.7 1/2
Equal percentage 12.7 0.5 19 0.75
19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
HPS Micro-Form
25.4 1 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
38.1 1.5 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Equal percentage 47.6 1.875 25.4 1 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear (Cage Style: Standard) 47.6 1.875 25.4 1 12.7, 19.1, 25.4 1/2, 3/4, 1
HPS Standard Linear (Cage Style: Whisper Trim III,
2 47.6 1.875 38 1.50 12.7, 19.1 1/2, 3/4
Level A1)
Linear
25.4 1 51 2 19.1 3/4
Equal percentage 47.6 1.875 25.4 1 12.7, 19.1 1/2, 3/4
HPD Linear (Cage Style: Standard) 47.6 1.875 25.4 1 12.7, 19.1 1/2, 3/4
47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Level A1)
Equal percentage 47.6 1.875 25.4 1 12.7, 19.1 1/2, 3/4
Linear (Cage Style: Standard) 47.6 1.875 25.4 1 12.7, 19.1 1/2, 3/4
HPT Linear (Cage Style: Whisper Trim III,
47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Level A1)
Linear
44.5 1.75 51 2 12.7, 19.1 1/2, 3/4
‐continued‐
21
Product Bulletin
51.2:HP HP Valve
Table 10. Globe Valve Specifications for CL2500 through CL3200 (continued)
AND PLUG STYLE
Linear (Cage Style: Standard) 57.15 2.25 38 1.5 19.1, 25.4 3/4, 1
Modified equal percentage 57.15 2.25 38 1.5 19.1, 25.4 3/4, 1
HPS 57.15 2.25 38 1.5 19.1, 25.4 3/4, 1
Level A1, A3, B1, B3, C1, C3)
35 1.375 51 2 19.1, 25.4 3/4, 1
Level D3)
Linear (Cage Style: Standard) 57.15 2.25 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
3
Linear (Cage Style:Whisper Trim III,
57.15 2.25 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Level A1, A3, B1, B3, C1, C3)
HPD, HPT 35 1.375 51 2 19.1, 25.4 3/4, 1
Level D3)
Linear
57.15 2.25 64 2.5 19.1, 25.4 3/4, 1
Linear
35 1.375 64 2.5 19.1, 25.4 3/4, 1
HPS 57.15 2.250 51 2.0 19.1, 25.4 3/4, 1
Level D3)
Modified equal percentage 73.7 2.90 51 2 19.1, 25.4 3/4, 1
Linear (Cage Style: Standard) 73.7 2.90 51 2 19.1, 25.4 3/4, 1
73.7 2.90 51 2 19.1, 25.4 3/4, 1
Level A1, A3, B1, B3, C1, C3)
4
HPD, HPT 57.15 2.25 51 2 19.1, 25.4 3/4, 1
Level D3)
Linear
73.7 2.90 69.9 2.75 25.4 1
Linear
57.15 2.25 69.9 2.75 19.1, 25.4 3/4, 1
Modified equal percentage 105.9 4.17 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Linear (Cage Style: Standard) 105.9 4.17 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
105.9 4.17 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Level A1, A3, B1, B3, C1, C3)
6 HPD, HPT 105.9 4.17 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Level D3)
Linear
105.9 4.17 95.3 3.75 25.4, 31.8 1, 1-1/4
Linear
105.9 4.17 95.3 3.75 25.4, 31.8 1, 1-1/4
Equal percentage 139.7 5.50 76.2 3 31.8 1-1/4
Linear (Cage Style: Standard) 139.7 5.50 76.2 3 31.8 1-1/4
139.7 5.50 101.6 4 31.8 1-1/4
Level A1, A3)
8(1) HPD, HPT 139.7 5.50 127 5 31.8 1-1/4
Linear
139.7 5.50 127 5 31.8 1-1/4
Linear
139.7 5.50 127 5 31.8 1-1/4
‐continued‐
22
Product Bulletin
HP Valve 51.2:HP
Table 10. Globe Valve Specifications for CL2500 through CL3200 (continued)
AND PLUG STYLE
Equal percentage 165.1 6.50 101.6 4 31.8 1-1/4
Linear (Cage Style: Standard) 165.1 6.50 76.2 3 31.8 1-1/4
165.1 6.50 101.6 4 31.8 1-1/4
Level A1, A3)
10(1) HPD, HPT 165.1 6.50 127 5 31.8 1-1/4
Linear
165.1 6.50 127 5 31.8 1-1/4
Linear
165.1 6.50 127 5 31.8 1-1/4
Equal percentage 190.5 7.50 127 5 32.75, 50.8 1-1/4, 2
Linear (Cage Style: Standard) 190.5 7.50 127 5 32.75, 50.8 1-1/4, 2
190.5 7.50 127 5 32.75, 50.8 1-1/4, 2
Level A1, A3)
12(1) HPD, HPT 190.5 7.50 152.4 6 32.75, 50.8 1-1/4, 2
Linear
190.5 7.50 152.4 6 32.75, 50.8 1-1/4, 2
Linear
190.5 7.50 152.4 6 32.75, 50.8 1-1/4, 2
Equal percentage 215.9 8.50 127 5 32.75, 50.8 1-1/4, 2
Linear (Cage Style: Standard) 215.9 8.50 127 5 32.75, 50.8 1-1/4, 2
215.9 8.50 127 5 32.75, 50.8 1-1/4, 2
Level A1, A3)
14 HPD, HPT 215.9 8.50 152.4 6 32.75, 50.8 1-1/4, 2
Linear
215.9 8.50 152.4 6 32.75, 50.8 1-1/4, 2
Linear
215.9 8.50 152.4 6 32.75, 50.8 1-1/4, 2
1. Includes CL3200 intermediate rating.
23
Product Bulletin
51.2:HP HP Valve
Table 11. Globe and Angle Valve Yoke Boss and Valve Stem Diameter Combinations(1)
VALVE STANDARD DIAMETERS OPTIONAL DIAMETERS
SIZE, mm Inches mm Inches
NPS Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss
1 12.7 71 0.5 2-13/16 19.1 90 0.75 3-9/16
12.7 71 0.5 2-13/16
2 25.4 127 1 5
19.1 90 0.75 3-9/16
12.7 71 0.5 2-13/16
3 19.1 90 0.75 3-9/16
25.4 127 1 5
4 19.1 90 0.75 3-9/16 25.4 127 1 5
25.4 127 1 5
6 19.1 71 0.75 3-9/16
31.8 127 1.25 5
6(2) 19.1 90 0.75 3-9/16 25.4 127 1 5
25.4 127 1 5
8(2) 19.1 71 0.75 3-9/16
31.75 127 1.25 5H
25.4 127 1 5
8 31.75 127 1.25 5H
50.8 177.8 2 7
25.4 127 1 5
10 31.75 127 1.25 5H
50.8 177.8 2 7
25.4 127 1 5
12 31.75 127 1.25 5H
50.8 177.8 2 7
12(2) 31.75 127 1.25 5H --- --- --- ---
14 31.75 127 1.25 5H 50.8 177.8 2 7
1. See tables 9, 10, and 12 for valve stem diameters available for specific constructions.
2. Angle valve construction only (HPAD, HPAT).
24
Product Bulletin
HP Valve 51.2:HP
Table 12. Additional Angle Valve Specifications

VALVE VALVE BODY PORT VALVE PLUG
FLOW FLOW VALVE STEM DIAMETER
SIZE, DESIGN AND DIAMETER TRAVEL
CHARACTERISTIC DIRECTION
NPS PLUG STYLE mm Inches mm Inches mm Inches
6.4 0.25 19 0.75 12.7 1/2
HPAS w/Micro-Flute Up(2) 9.5 0.375 19 0.75 12.7 1/2
12.7 0.5 19 0.75 12.7 1/2
6.4 0.25 19 0.75 12.7 1/2
Equal
12.7 0.5 19 0.75 12.7 1/2
HPAS w/Micro-Form percentage Up
19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
25.4 1 19 0.75 12.7, 19.1 1/2, 3/4
HPAS, equal
Down 19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
percentage characterized cage
1
12.7 0.5 29 1.125 12.7, 19.1 1/2, 3/4
HPAS w/Micro-Form Modified Up 19.1 0.75 29 1.125 12.7, 19.1 1/2, 3/4
equal 25.4 1 29 1.125 12.7, 19.1 1/2, 3/4
percentage
HPAS Down 19.1 0.75 29 1.125 12.7, 19.1 1/2, 3/4
9.5 0.375 19 0.75 12.7 1/2
Linear (cage
HPAS w/ Micro-Flat Down 12.7 0.5 19 0.75 12.7 1/2
style: Std)
19.1 0.75 19 0.75 19.1 3/4
Linear (cage style:
HPAS Down 22.2 0.875 38 1.5 12.7, 19.1 1/2, 3/4
Cavitrol III, 2-stage)
6.4 0.25 19 0.75 12.7 1/2
HPAS w/Micro-Flute Up(2) 9.5 0.375 19 0.75 12.7 1/2
12.7 0.5 19 0.75 12.7 1/2
6.4 0.25 19 0.75 12.7 1/2
12.7 0.5 19 0.75 12.7 1/2
19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
HPAS w/Micro-Form Up
25.4 1 19 0.75 12.7, 19.1, 25.4 1/2, 3/4, 1
Equal 31.8 1.25 19 0.75 12.7, 19.1, 25.4 1/2, 3/4, 1
percentage 38.1 1.5 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
19.1 0.75 19 0.75 12.7, 19.1, 25.4 1/2, 3/4, 1
HPAS, equal 25.4 1 19 0.75 12.7, 19.1, 25.4 1/2, 3/4, 1
Down
percentage characterized cage 31.8 1.25 19 0.75 19.1, 25.4 3/4, 1
38.1 1.5 29 1.125 19.1, 25.4 3/4, 1
HPAS Up 47.6 1.875 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
HPAT, HPAD Down 47.6 1.875 29 1.125 12.7, 19.1 1/2, 3/4
12.7 0.5 29 1.125 12.7 1/2
19.1 0.75 29 1.125 12.7, 19.1 3/4
HPAS w/Micro-Form Up 25.4 1 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
2 31.8 1.25 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
38.1 1.5 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Modified equal 19.1 0.75 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
HPAS, equal percentage 25.4 1 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
Down
percentage characterized cage 31.8 1.25 29 1.125 19.1, 25.4 3/4, 1
38.1 1.5 38 1.5 19.1, 25.4 3/4, 1
HPAS Up 47.6 1.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
HPAT, HPAD Down 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Linear (cage
HPAS w/Micro-Flat Down 25.4 1 29 1.125 19.1 3/4
style: std)
HPAS Linear (cage Up 47.6 1.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
HPAT, HPAD style: std) Down 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Linear (cage style:
HPAS, HPAT, HPAD Up 47.6 1.875 38 1.5 12.7, 19.1, 25.4(1) 1/2, 3/4, 1(1)
Whisper III, level A1)
Linear (cage style:
HPAT Down 44.5 1.75 51 2 12.7, 19.1 1/2, 3/4
Linear (cage style:
HPAS Down 25.4 1 51 2 19.1 3/4
‐continued‐
25
Product Bulletin
51.2:HP HP Valve
Table 12. Additional Angle Valve Specifications (continued)

Equal percentage Down 47.6 1.875 29 1.125 12.7, 19.1 1/2, 3/4
Modified equal
Down 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
percentage
HPAT, HPAD
Linear (cage style: Std) Down
3
Linear (cage style: 47.6 1.875 38 1.5 12.7, 19.1 1/2, 3/4
Up
Whisper III, level A1)
Linear (cage style:
HPAT Down 44.5 1.75 51 2 12.7, 19.1 1/2, 3/4
Equal percentage Down 73 2.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Modified equal
Down
percentage
HPAT, HPAD Linear (cage style: Std) Down
73 2.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear (cage style:
4 Whisper III, level A1, Up
B1)
Linear (cage style:
Down 64 2.5 64 2.5 12.7, 19.1, 25.4 1/2, 3/4, 1
HPAT
Linear (cage style:
Down 47.6 1.875 64 2.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Equal percentage Down 92.1 3.625 38 1.5 19.1, 25.4 3/4, 1
Modified equal
Down
percentage
92.1 3.625 51 2 19.1, 25.4 3/4, 1
HPAT, HPAD Linear (cage style:
Whisper III, level A1, Up
6 (long)(3) A3, B3, C3)
Linear (cage style:
Up 73 2.875 51 2 19.1, 25.4 3/4, 1
Whisper III, level D3)
Linear (cage style:
Down 87.3 3.4375 76 3 19.1, 25.4 3/4, 1
HPAT
Linear (cage style:
Down 73 2.875 76 3 19.1, 25.4 3/4, 1
Linear Down
Modified Equal
Down
Percent
73.7 2.9 69.9 2.75 19.1, 25.4 3/4, 1
Linear (cage style:
A3, B1, B3, C1, C3)
6 (short)(3) HPAD, HPAT
Linear (cage style:
Up 57.2 2.25 50.8 2 19.1, 25.4 3/4, 1
Linear (cage style:
Down 73.7 2.9 69.9 2.75 25.4 1
Linear (cage style:
Down 57.2 2.25 69.9 2.75 25.4 1
‐continued‐
26
Product Bulletin
HP Valve 51.2:HP
Table 12. Additional Angle Valve Specifications (continued)

Equal percentage Down 136.5 5.375 64 2.5 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Modified equal
Down
percentage 136.5 5.375 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
HPAT, HPAD Linear (cage style:
Whisper III, level A1, Up 136.5 5.375 76 3 25.4, 31.8 1, 1-1/4
8 A3, B3, C3)
Linear (cage style:
Up 111.1 4.375 76 3 25.4, 31.8 1, 1-1/4
Linear (cage style:
Down 133.4 5.25 102 4 19.1, 25.4, 31.8 3/4, 1, 1-1/4
HPAT
Linear (cage style:
Down 115.9 4.5625 102 4 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Linear Down
Modified Equal
Down
Percent
105.9 4.17 95.3 3.75 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Linear (cage style:
A3, B1, B3, C1, C3)
8 (short)(3) HPAD, HPAT
Linear (cage style:
Up 105.9 4.17 76.2 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Linear (cage style:
Down 105.9 4.17 95.3 3.75 25.4, 31.8 1, 1-1/4
Linear (cage style:
Down 105.9 4.17 95.3 3.75 19.1, 25.4, 31.8 1, 1-1/4
Linear Down 165.1 6.5 101.6 4 31.8 1, 1-1/4
Modified Equal
Down
Percent
Linear (cage style:
Whisper III, level A1,
Up
12 HPAD, HPAT A3, B1, B3, C1, C3,
D3) 165.1 6.5 127 5 31.8 1, 1-1/4
Linear (cage style:
Down
Linear (cage style:
Down
1. Available only with HPAS valves.
2. Micro-Flutes (1 flute and 0.5 inch port 2 flute) may be used flow down in flashing and erosive service.
3. (Long) indicates industry standard long face-to-face. (Short) indicates industry standard short face-to-face.
27
Product Bulletin
51.2:HP HP Valve
Figure 10. Fisher HPS Trim with Micro-Flute Valve Figure 11. Fisher HPS Trim with Micro-Form Valve
Plug Plug
W5817-1
W5816-1
FLOW
FLOW
n Trim 203— Trim 203 is the standard trim for

stainless steel valve body materials and should only
Trim Selection Guidelines be used with stainless steel valve body materials.
This trim meets the metallurgical requirements of
NACE MR0175-2002 and can be used in applications
NPS 1 through 6 HP Globe Valve, up to 593_C (1100_F)
NPS 8 Angle Body Valve

n Trim 204— Trim 204 is used in sour or moderately
Refer to the following descriptions as a guideline for corrosive services. This trim meets the metallurgical
the selection of appropriate trims.
requirements of NACE MR01752002 and can be
n Trim 201A— Trim 201A is the standard trim for used with carbon steel and alloy steel valve body
carbon steel and alloy steel valve body materials. materials.
This trim is recommended for general or severe
service applications up to 343_C (650_F) or 427_C n Trim 210— Provides a S31600 CoCr-A hardfaced
(800_F) depending on valve construction. Typical valve plug, which can be easily weld repaired. The
applications for this trim include services in boiler S17400 H1075 cage in this trim also allows it to be
feedwater, water, nonsour hydrocarbons, and used in an HPT or HPAT construction.
steam.
n Trims 202 and 202H— Trims 202 and 202H are n Trim 211— Trim 211 is the standard trim for C12A
designed for use in high temperature applications valve body materials and should only be used with
up to 566_C (1050_F). Trim 202H includes special C12A valve body materials. C12A should only be
tolerances required for larger sized HPD and HPAD used when the pressure and temperature
constructions, as indicated in table 13, at operating capabilities for WC9 valve body materials are not
temperatures above 343_C (650_F). acceptable.
28
Product Bulletin
HP Valve 51.2:HP
Figure 12. NPS 2 Fisher HPS Trim with Figure 14. Fisher HPAS Trim with
Cavitrol III 3-Stage Cage Micro-Flat Valve Plug
W6021-1
W5818-1
FLOW FLOW
Figure 13. Fisher HPD Trim with Figure 15. Fisher HPT Trim with
Whisper Trim III Level D Cage Whisper Trim III Level A1 Cage
(also available in HPT and HPS) (also available in HPD NPS 2-6 and HPS NPS 2 and 3)
W5951-1 W5952-1
FLOW FLOW
29
Product Bulletin
51.2:HP HP Valve
C-seal Trim Description Bore-seal plug seal is formed from metal (N07718
nickel alloy) rather than an elastomer, a valve
C-seal trim is available for HPD and HPAD valves with equipped with the Bore-seal trim can be applied in
port diameters from 2.875 inches through 5.375 processes with a fluid temperature of up to 593_C
inches. (1100_F).
With C-seal trim, a balanced valve can achieve

high-temperature, Class V shutoff. Because the C-seal
plug seal is formed from metal (N07718 nickel alloy) Fisher TSO (Tight Shutoff) Trim
rather than an elastomer, a valve equipped with the
C-seal trim can be applied in processes with a fluid Capabilities
temperature of up to 593_C (1100_F). TSO trim is available for HPS and HPT valves with port
diameters as defined in table 5. Also see figure 6 and
table 4.
Bore-seal Trim Description
TSO trim consists of a protected soft seat plus PEEK
Bore-seal trim is available for HPD valves with port anti-extrusion rings with a spring-loaded PTFE plug
diameters from 5.5 inches through 8.5 inches. seal. Used only in flow down applications, TSO trim
offers unparalleled shutoff integrity, resulting in longer
With Bore-seal trim, a balanced valve can achieve plug and seat life. For additional information contact
high-temperature, Class V shutoff. Because the your Emerson sales office.
Table 13. Trim Descriptions

OPERATING TEMPERATURE
TRIM VALVE BODY RANGE(2)
VALVE VALVE PLUG CAGE SEAT RING
DESIGNATION MATERIAL(1)
_C _F
With Standard Cage
S41600 heat-treated
for HP, HPA, WCC -29 to 343(8) -20 to 650(8)
S41600 heat-treated
Micro-Form (HPA),
HP (NPS 1-6 CL900 & or
and flow down
1500 & NPS 1-2 CL2500) HPA (S44004
HPAS) or S17400 (17-4 SST)
201A HPA (NPS 1-8 CL900 heat-treated seat ring LCC -29 to 343 -20 to 650
S44004 (440C SST) H1075 heat-treated
&1500 & NPS 1-2 for Micro-Flat
heat-treated for
CL2500) S44004 heat-treated
Micro-Flute and
seat and liner) WC9 -29 to 343(8) -20 to 650(8)
Micro-Flat (HPA only)
valve plugs
HPD & HPS only (NPS 1-6
S31600/CoCr-A WCC -29 to 427 -20 to 800
CL900 & 1500 & NPS 1 S31600 (316
F22 or
to 2 CL2500) stainless steel) with
202 (Cr-Mo alloy steel) R30006 (Alloy 6) for LCC -46 to 343 -50 to 650
HPAD & HPAS only (NPS CoCr-A seat and
nitrided Micro-Flat valve plugs
1-8 CL900 & 1500 & NPS guide
R30006 seat, liner(3) WC9 -29 to 566 -20 to 1050
1-2 CL2500)
HPD NPS 6 CL900 & S31600 (316 WCC 260 to 427 500 to 800
F22
1500, stainless steel) with
202H(4) (Cr-Mo alloy steel) S31600/CoCr-A LCC 260 to 343 500 to 650
HPAD NPS 8 CL900 & CoCr-A seat and
nitrided WC9 260 to 566 500 to 1050
1500 only guide
S31600/CoCr-A
HP (NPS 1-6 CL900 &
or
1500 & NPS 1-2 CL2500) S31600 with CoCr-A S31600/hard
203 (NACE)(12) R30006 (Alloy 6) for CF8M -198 to 593(2) -325 to 1100(2)
HPA (NPS 1-8 CL900 & seat and guide Cr coat
Micro-Flat valve plugs
1500 & NPS 1-2 CL2500)
R30006 seat, liner(3)
203A S31600 with CoCr-A
HP (NPS 1-6 1500) S31600/Cr plate S31600/CoCr-A CF8M -198 to 316 -325 to 600
(NACE)(12) seat and guide
S31600/CoCr-A WCC -29 to 427 -20 to 800
HP (NPS 1-6 CL900 &
or
1500 & NPS 1-2 CL2500) S31600 with CoCr-A S17400 Double
204 (NACE)(12) R30006 (Alloy 6) for LCC -46 to 343 -50 to 650
HPA (NPS 1-8 CL900 & seat and guide H1150 heat-treated
Micro-Flat valve plugs
1500 & NPS 1-2 CL2500) WC9 -29 to 427 -20 to 800
R30006 seat, liner(3)
‐continued‐
30
Product Bulletin
HP Valve 51.2:HP
Table 13. Trim Descriptions (continued)

_C _F
With Standard Cage
HP (NPS 1-6 CL900 & WCC -29 to 427 -20 to 800
1500 & NPS 1-2 CL2500) S31600 with CoCr-A
210 S17400 H1075 S31600/CoCr-A LCC -46 to 343 -50 to 650
HPA (NPS 1-8 CL900 & seat and guide
1500 & NPS 1-2 CL2500) WC9 -29 to 427 -20 to 800
HPD & HPS only (NPS 1-6
CL900 & 1500 & NPS 1
to 2 CL2500) F91 with CoCr-A
211(9) F91 ion nitrided F91 with CoCr-A C12A -29 to 593 -20 to 1100
HPAD & HPAS only (NPS seat and guide
1-8 CL900 & 1500 & NPS
1-2 CL2500)
HP (NPS 8-14 CL900, WCC, WC9 -29 to 427 -20 to 800
410/416 SST S17400 H1075 S17400 H1075
260 1500, 2500, & 3200)
heat treated heat treated heat treated LCC -46 to 343 -50 to 650
HPA (NPS12)
410/416 SST S17400 H1075
260S(13) 1500, 2500, & 3200) S41600 heat treated
heat treated heat treated LCC -46 to 343 -50 to 650
HPA (NPS 12)
HP (NPS 3, 4, 6 CL900, WCC, WC9 -29 to 427 -20 to 800
410/416 SST S17400 H1075
360S(13) 1500, & 2500) HPA S41600 heat treated
heat treated heat treated LCC -46 to 343 -50 to 650
(NPS 6 & 8 CL2500)
HP (NPS 8-14 CL900,
2.25 Cr - 1 Mo with 2.25 Cr - 1 Mo 2.25 Cr - 1 Mo with
262 1500, 2500, & 3200) WC9, C12A -29 to 566 -20 to 1050
CoCr-A Nitrided CoCr-A
HPA (NPS 12)
HP (NPS 8-14 CL900,
262S(13) 1500, 2500, & 3200) WC9, C12A -29 to 566 -20 to 1050
HPA (NPS 12)
HP (NPS 3, 4, 6 CL900, WC9 -29 to 566 -20 to 1050
362S(13) 1500, & 2500) HPA
CoCr-A Nitrided CoCr-A C12A -29 to 593 -20 to 1100
(NPS 6 & 8 CL2500)
HP (NPS 8-14 CL900, CF8M, CF8C -198 to 316 -325 to 600

263 S31600 with S31600 with Cr
1500, 2500, & 3200) S31600 with CoCr-A WCC, WC9 -29 to 316 -20 to 600
(NACE)(11)(12) CoCr-A plating
HPA (NPS 12) LCC -46 to 316 -50 to 600
HP (NPS 8-14 CL900, CF8M, CF8C -198 to 316 -325 to 600

263S(13) S31600 with S31600 with Cr
1500, 2500, & 3200) S31600 with CoCr-A WCC, WC9 -29 to 316 -20 to 600
HPA (NPS 12) LCC -46 to 316 -50 to 600
HP (NPS 3, 4, 6 CL900, CF8M, CF8C -198 to 316 -325 to 600

363S(13) S31600 with S31600 with Cr
1500, & 2500) HPA S31600 with CoCr-A WCC, WC9 -29 to 316 -20 to 600
(NPS 6 & 8 CL2500) LCC -46 to 316 -50 to 600
CF8M, CF8C -198 to 593 -325 to 1100(14)
HP (NPS 8-14 CL900, WCC -29 to 399 -20 to 750(15)
264 S31600 with S31600 with Cr
1500, 2500, & 3200) S31600 with CoCr-A
(NACE)(11)(12) CoCr-A coating LCC -46 to 343 -50 to 650
HPA (NPS 12)
WC9 -29 to 427 -20 to 800(15)
CF8M, CF8C -198 to 593 -325 to 1100(14)
HP (NPS 8-14 CL900, WCC -29 to 399 -20 to 750(15)
264S(13) S31600 with S31600 with Cr
1500, 2500, & 3200) S31600 with CoCr-A
(NACE)(11)(12) CoCr-A coating LCC -46 to 343 -50 to 650
HPA (NPS 12)
WC9 -29 to 427 -20 to 800(15)
CF8M, CF8C -198 to 593 -325 to 1100(16)
HP (NPS 3, 4, 6 CL900, WCC -29 to 427 -20 to 800(17)
364S(13) S31600 with S31600 with Cr
1500, & 2500) HPA S31600 with CoCr-A
(NACE)(11)(12) CoCr-A coating LCC -46 to 343 -50 to 650(18)
(NPS 6 & 8 CL2500)
WC9 -29 to 454 -20 to 850(17)
265 HP (NPS 14 CL2500) S34700 with S34700 with Cr
S34700 with CoCr-A CF8C -198 to 593 -325 to 1100(14)
(NACE)(11)(12) HPA (NPS 12) CoCr-A Coating
‐continued‐
31
Product Bulletin
51.2:HP HP Valve

_C _F
With Standard Cage
265S(13) HP (NPS 14 CL2500) S34700 with S34700 with Cr
S34700 with CoCr-A CF8C -198 to 593 -325 to 1100(14)
(NACE)(11)(12) HPA (NPS 12) CoCr-A Coating
HP (NPS 3, 4, 6 CL900,
365S(13) S34700 with S34700 with Cr
1500, & 2500) HPA S34700 with CoCr-A CF8C -198 to 593 -325 to 1100(16)
(NACE)(11)(12) CoCr-A Coating
(NPS 6 & 8 CL2500)
HP (NPS 1-6 CL900,
1500 & NPS 1-2 S17400/tungsten S17400/Tungsten
TC1 CL2500) carbide insert for R30006 carbide insert WCC, WC9 -29 to 232 -20 to 450
HPA (NPS 1-8 CL900, seat & contour (10) for seat & bore
1500 & NPS 1-2 CL2500)
HP (NPS 1-6 CL900,
S32550/tungsten S32550/tungsten
1500 & NPS 1-2 CL2500) CF8M, CD3MN,
TC2 carbide insert for R30006 carbide insert for seat -29 to 93 -20 to 200
HPA (NPS 1-8 CL900, CD3MWCuN
seat & contour (10) & bore
1500 & NPS 1-2 CL2500)
HP (NPS 1-6 CL900,
N07718/tungsten N07718/tungsten
1500 & NPS 1-2 CL2500)
TC3 carbide insert for R30006 carbide insert for seat CW6MC -29 to 232 -20 to 450
HPA (NPS 1-8 CL900,
seat & contour (10) & bore
1500 & NPS 1-2 CL2500)
v 1/4 inch Port:
R30006 or R30016
> 1/4 inch, < 3 inch
HP (NPS 1-6 Port: S31803 with
751 S31803/Cr Pl S31803/CoCr A CD3MN -51 to 316 -60 to 600
CL900 & 1500) CoCr-A seat and
guide
w 3 inch Port:
S31803/Ultimet
v 1/4 inch Port:
R30006 or R30016
HP (NPS 1-6 Port: S32760 with
752 S32760/Cr Pl S32760/CoCr A CD3MWCuN -51 to 316 -60 to 600
CL900 & 1500) CoCr-A seat and
guide
w 3 inch Port:
S32760/Ultimet
With Cavitrol III Cage
HP (NPS 1-6 CL900 & S42000 WCC
1500 & NPS 1-2 CL2500) or
S17400
215A S44004 heat-treated S44004 heat-treated LCC -29 to 343(8) -20 to 650(8)
H1075 heat-treated
HPA (NPS 1-8 CL900 & for CAV III Micro-Flat
1500 & NPS 1-2 CL2500) only WC9
HP (NPS 1-6 CL900 & S42000 WCC
1500 & NPS 1-2 CL2500) or
S17400
215B(6) S44004 heat-treated S44004 heat-treated LCC -29 to 343(8) -20 to 650(8)
H1075 heat-treated
HPA (NPS 1-8 CL900 & for CAV III Micro-Flat
1500 & NPS 1-2 CL2500) only WC9
HP (NPS 1-6 CL900 & WCC -29 to 343 -20 to 650
1500 & NPS 1-2 CL2500)
S31600 with CoCr-A S17400 Double
206 (NACE)(5) S31600/CoCr-A LCC -46 to 343 -50 to 650
seat and guide H1150 heat-treated
HPA (NPS 1-8 CL900 &
1500 & NPS 1-2 CL2500) WC9 -29 to 343 -20 to 650
HP (NPS 3, 4, 6 CL900, WCC, WC9 -29 to 316 -20 to 600

306S(13) 1500, & 2500) S31600 with CoCr-A S17400 Double
S31600/CoCr-A LCC -46 to 316 -50 to 600
(NACE)(5) HPA (NPS 6 & 8 seat and guide H1150 heat-treated
CL2500) CF8M, CF8C -29 to 316 -20 to 600(20)
‐continued‐
32
Product Bulletin
HP Valve 51.2:HP

_C _F
With Cavitrol III Cage
1500, 2500, & S17400 H1075 S17400 H1075
275 S42000 heat treated LCC -46 to 343 -50 to 650
3200)HPA (NPS 12 heat treated heat treated
CL2500) CF8M, CF8C -29 to 232 -20 to 450
1500, 2500, & 3200) S17400 H1075
275S(13) S42000 heat treated S42000 heat treated LCC -46 to 343 -50 to 650
HPA (NPS 12 heat treated
CL2500) CF8M, CF8C -29 to 232 -20 to 450
HP (NPS 3, 4, 6 WCC, WC9 -29 to 427 -20 to 800
CL900, 1500, & S17400 H1075
2500) HPA (NPS 6 & heat treated
8 CL2500) CF8M, CF8C -29 to 343 -20 to 650(19)
1500, 2500, & 3200) S17400 H1075 S17400 H1075
HPA (NPS 12 heat treated heat treated
CL2500) CF8M, CF8C -29 to 232 -20 to 450
1500, 2500, & 3200) S17400 H1075
HPA (NPS 12 heat treated
CL2500) CF8M, CF8C -29 to 232 -20 to 450
WCC, WC9 -29 to 427 -20 to 800
HP (NPS 8-12 CL900, S17400 H1075 S17400 H1075
1500, 2500, & 3200) heat treated heat treated
CF8M -29 to 232 -20 to 450
WCC, WC9 -29 to 427 -20 to 800
HP (NPS 8-12 CL900, S17400 H1075 S17400 H1075
1500, 2500, & 3200) heat treated heat treated
CF8M -29 to 232 -20 to 450
v 1/4 inch Port:
R30006 or R30016
HP (NPS 1-6
753 Port: S31803 with S32760 S31803/CoCr A CD3MN -51 to 316(7) -60 to 600(7)
CL900 & 1500)
CoCr-A seat and guide
w 3 inch Port:
S31803/Ultimet
v 1/4 inch Port:
R30006 or R30016
HP (NPS 1-6
754 Port: S32760 with S32760 S32760/CoCr A CD3MWCuN -51 to 316(7) -60 to 600(7)
CL900 & 1500)
w 3 inch Port:
S32760/Ultimet
With Whisper Trim III Cage
HP (NPS 1-6 CL900 &
WCC
1500 & NPS 1-2
CL2500) S17400 S41600
207A S41600 heat-treated LCC -29 to 343(8) -20 to 650(8)
HPA (NPS 1-8 CL900 & H1075 heat-treated heat-treated
1500 & NPS 1-2
WC9
CL2500)
HP (NPS 3, 4, 6
CL900, 1500, & WCC, WC9 -29 to 427 -20 to 800
S17400 S41600
307S(13) 2500) S41600 heat-treated
H1075 heat-treated heat-treated
HPA (NPS 6 & 8
LCC -46 to 343 -50 to 650
CL2500)
‐continued‐
33
Product Bulletin
51.2:HP HP Valve

_C _F
HP (NPS 1-6 CL900 & WCC -29 to 427 -20 to 800
S17400
207B 1500 & NPS 1-2 S41600 heat-treated S31600/CoCr-A LCC -29 to 343 -20 to 650
H1075 heat-treated
CL2500 WC9 -29 to 427 -20 to 800
HPD & HPS only (NPS
WCC -29 to 427 -20 to 800
1-6 CL900 & 1500 &
F22
NPS 1 to 2 CL2500) S31600 with CoCr-A
208 (Cr-Mo alloy steel) S31600/CoCr-A LCC -46 to 343 -50 to 650
HPAD & HPAS (NPS seat and guide
nitrided
1-8 CL900 & 1500 &
WC9 -29 to 566 -20 to 1050
NPS 1-2 CL2500)
HPD (NPS 6 CL900 & WCC -29 to 427 -20 to 800
F22
1500) S31600 with CoCr-A
208H(4) (Cr-Mo alloy steel) S31600/CoCr-A LCC -46 to 343 -50 to 650
HPAD (NPS 8 CL900 & seat and guide
nitrided WC9 -29 to 566 -20 to 1050
1500 only)
HP (NPS 1-6 CL900 &
WCC -29 to 343 -20 to 650
1500 & NPS 1-2
CL2500) S31600 with CoCr-A S17400 Double
209 (NACE)(5) S31600/CoCr-A LCC -46 to 343 -50 to 650
HPA (NPS 1-8 CL900 & seat and guide H1150 heat-treated
1500 & NPS 1-2
WC9 -29 to 343 -20 to 650
CL2500)
HPD & HPS only (NPS
1-6 CL900 & 1500 &
NPS 1 to 2 CL2500)
F91 with CoCr-A
212(9) HPAD & HPAS only F91 ion nitrided F91 with CoCr-A C12A -29 to 593 -20 to 1100
seat and guide
(NPS 1-8 CL900 &
1500 & NPS 1-2
CL2500)
HP (NPS 8-14 CL900, 410/416 SST S17400 H1075 S17400 H1075 WCC, WC9 -29 to 427 -20 to 800
286A
1500, 2500, & 3200) heat treated heat treated heat treated LCC -46 to 343 -50 to 650
HP (NPS 8-14 CL900,
WCC, WC9 -29 to 427 -20 to 800
1500, 2500, & 3200) 410/416 SST S17400 H1075 S41600 SST heat
286S(13)
HPA (NPS 12 heat treated heat treated treated
LCC -46 to 343 -50 to 650
CL2500)
HP (NPS 8-14 CL900,
WC9 -29 to 566 -20 to 1050
1500, 2500, & 3200) 2.25 Cr - 1 Mo with 2.25 Cr - 1 Mo 2.25 Cr - 1 Mo with
287
HPA (NPS 12 CoCr-A Nitrided CoCr-A
LCC -46 to 343 -50 to 650
CL2500)
HP (NPS 8-14 CL900,
1500, 2500, & 3200) 2.25 Cr - 1 Mo with 2.25 Cr - 1 Mo 2.25 Cr - 1 Mo with
287S(13) WC9 -29 to 566 -20 to 1050
HPA (NPS 12 CoCr-A Nitrided CoCr-A
CL2500)
HP (NPS 3, 4, 6
CL900, 1500, &
387S(13) 2500) WC9 -29 to 566 -20 to 1050
HPA (NPS 6 & 8
CL2500)
HP (NPS 8-14 CL900,
9 Cr - 1 Mo - V 9 Cr - 1 Mo - V C12A -29 to 566 -20 to 1100
1500, 2500, & 3200) 9 Cr - 1 Mo - V
288
HPA (NPS 12 Nitrided
with CoCr-A with CoCr-A LCC -46 to 343 -50 to 650
CL2500)
HP (NPS 8-14 CL900,
1500, 2500, & 3200) 9 Cr - 1 Mo - V 9 Cr - 1 Mo - V 9 Cr - 1 Mo - V
288S(13) C12A -29 to 566 -20 to 1100
HPA (NPS 12 with CoCr-A Nitrided with CoCr-A
CL2500)
‐continued‐
34
Product Bulletin
HP Valve 51.2:HP

_C _F
HP (NPS 3, 4, 6
CL900, 1500, & 9 Cr - 1 Mo - V 9 Cr - 1 Mo - V 9 Cr - 1 Mo - V
388S(13) C12A -29 to 566 -20 to 1100
2500) HPA (NPS 6 & with CoCr-A Nitrided with CoCr-A
8 CL2500)
HP (NPS 8-14 CL900, WCC, WC9, CF8M,
S17400 Double -29 to 260 -20 to 500
1500, 2500, & 3200) S17400 Double CF8C
289 (NACE)(5) S31600 with CoCr-A H1150 heat treated
HPA (NPS 12 H1150 heat treated
with CoCr-A LCC -46 to 260 -50 to 500
CL2500)
HP (NPS 8-14 CL900, WCC, WC9, CF8M,
-29 to 260 -20 to 500
289S(13) 1500, 2500, & 3200) S17400 Double CF8C
S31600 with CoCr-A S31600 with CoCr-A
(NACE)(5) HPA (NPS 12 H1150 heat treated
CL2500) LCC -46 to 260 -50 to 500
HP (NPS 3, 4, 6 WCC, WC9 -29 to 316 -20 to 600

CL900, 1500, &
389S(13) S17400 Double
2500) S31600 with CoCr-A S31600 with CoCr-A LCC -46 to 316 -50 to 600
(NACE)(5) H1150 heat treated
HPA (NPS 6 & 8
CF8M, CF8C -29 to 316 -20 to 600(21)
CL2500)
v 1/4 inch Port:
R30006 or R30016
HP (NPS 1-6
751 Port: S31803 with S31803/Cr Pl S31803/CoCr A CD3MN -51 to 316 -60 to 600
CL900 & 1500)
w 3 inch Port:
S31803/Ultimet
v 1/4 inch Port:
R30006 or R30016
HP (NPS 1-6
752 Port: S32760 with S32760/Cr Pl S32760/CoCr A CD3MWCuN -51 to 316 -60 to 600
CL900 & 1500)
w 3 inch Port:
S32760/Ultimet
1. If using valve body/trim combinations other than those listed, consult your Emerson sales office.
2. Temperatures above 538_C (1000_F) require a non-standard CF8M body material (CF8M to FMS 20B16).
3. For HPA valves.
4. Trims 202H and 208H have valve plug tolerances for high temperature service and are used in place of trims 202 and 208 for the constructions listed when operating temperatures exceed
343_C (650_F).
5. NACE MR0175-2002.
6. Trim 215B has a S31600 valve stem instead of the standard S20910 material.
7. NPS 1 2 stage and NPS 2 3 stage HPS can be used at temperatures up to 343_C (650_F).
8. NPS 1 and 2 can be used at temperatures up to 427_C (800_F).
9. Trims 211 and 212 use S41000 stem instead of the standard S20910 material. S41000 is limited to 538_C (1000_F). For temperatures greater than 538_C (1000_F), S42200 stem is used.
10. Use with Micro-Form trim in HPS, Micro-Form and Micro-Flat in HPAS valves.
11. Not available with bore seal.
12. NACE MRO175-2002, 2003, and NACE MRO103.
13. Separate seat and cage design trim.
14. NPS 12 angle limited to -198 to 510_C (-325 to 950_F).
16. NPS 6 CL2500 globe and NPS 6 angle limited to -198 to 482_C (-325 to 900_F). NPS 8 angle limited to -198 to 371_C (-325 to 700_F).
17. NPS 6 CL2500 globe limited to -29 to 343_C (-20 to 650_F). NPS 8 angle limited to 29 to 315_C (-20 to 600_F).
19. NPS 6 globe CL1500 and CL2500 limited to -29 to 232_C (-20 to 450_F). NPS 6 angle limited to -29 to 260_C (-20 to 500_F). NPS 8 angle limited to -29 to 176_C (-20 to 350_F).
20. NPS 6 globe CL1500 and CL2500 limited to -29 to 260_C (-20 to 500_F). NPS 6 angle limited to -29 to 287_C (-20 to 550_F). NPS 8 angle limited to -29 to 176_C (-20 to 350_F).
21. NPS 6 globe and angle CL1500 and CL2500 limited to -29 to 287_C (-20 to 550_F). NPS 8 angle limited to -45 to 287_C (-50 to 350_F).
35
Product Bulletin
51.2:HP HP Valve
Table 14. Flowing Pressure Drop Limits for NPS 6 (Long)(1) HPD and HPT Valves
(Without Cavitrol III or Whisper Trim III Cage)
MAXIMUM FLOWING
STEM PRESSURE DROP
FLOW
DIAMETER,
MEDIA Bar PSI
mm (INCHES)
Flow Down Flow Up Flow Down Flow Up
19 (3/4) 103 --- 1500 ---
All except 25.4 (1) 172 --- 2500 ---
boiler 31.8 (1-1/4) 259 --- 3750 ---
feedwater 51.8 x 31.8(2)
259 259 3750 3750
(2 x 1-1/4)
31.8 (1-1/4) 69 --- 1000 ---
Boiler
51.8 x 31.8(2)
feedwater 138 259 2000 3750
(2 x 1-1/4)
2. Requires 31.8 mm (1-1/4 inch) S20910 stem with 52.8 mm (2-inch) plug-to-stem connection.
Figure 16. Pressure-Temperature Limits for Trim Material Combinations (also refer to table 7)
−29 FLUID TEMPERATURE, −29 FLUID TEMPERATURE,
0 _C _C
200 400 600 0 200 400 600
PRESSURE DROP, BAR, DIFFERENTIAL

6000 400 6000 400
PRESSURE DROP, PSI
PRESSURE DROP, PSI

5000 5000
300 300
4000 4000
3000 201, 207 200 3000 202,208 202H, 200

208H
2000 2000
100 100
1000 1000
1
0 10 0 10
−20 200 400 600 800 1000 1200 −20 200 400 600 800 1000 1200
FLUID TEMPERATURE, _F 650
FLUID TEMPERATURE, _F 3
−40 FLUID TEMPERATURE, −40 FLUID TEMPERATURE, −73 FLUID TEMPERATURE,

_C _C _C
0 200 400 600 0 200 400 600 0 200 400 600

6000 6000 6000

400 400 400
210
PRESSURE DROP, PSI
PRESSURE DROP, PSI
PRESSURE DROP, PSI
5000 5000 5000

204, LIMIT FOR
209 300 3-STAGE 300 300
4000 4000 4000
203
LIMIT FOR 211
3000 200 3000 200 3000 200
2-STAGE 4 212
2000 2000 2000
206
100 100 100
1000 206 1000 1000
215 5
0 10 0 10 0 10
−40 200 400 600 800 1000 1200 −40 200 400 600 800 1000 1200 −100 200 400 600 800 1000 1200
C0746-5 FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F
SOUR SERVICE APPLICATIONS (NACE) 2
Notes:
1 Use trim 207B in NPS 3, 4, 6 HP and NPS 4, 6, 8 HPA above 343_C (650_F).
2 NACE MR0175-2002.
3 Be especially careful to specify service temperature if trim 202 or 208 is selected, as different thermal expansion rates require special plug clearances.
4 The limit for 2-stage NPS 1 and 2 valves is 2160 psig. For NPS 3 to 6 valves the limit is 1800 psig.
5 Use trim 215 up to 427_C (800_ F) for NPS 1 and 2.
36
Product Bulletin
HP Valve 51.2:HP
Figure 17. Pressure-Temperature Limits for Standard Window Cage (also refer to table 7)
LIMITS FOR NPS 8, 10, 12 CL900 HP LIMITS FOR NPS 8, 10, 12 CL1500 HP
WITH STD TRIM 260, 262, 263, 264 WITH STD TRIM 260, 262, 263, 264
2500 4000 STD, SHUTOFF dP
STD, FLOWING dP
SHUTOFF dP 3500
2000
PRESSURE DROP, PSI
STD, FLOWING dP
PRESSURE DROP, PSI

3000
TRIM 260, 264 WC9 BODY

2500
TRIM 260, 264 WC9 BODY

1500
TRIM 264 WCC BODY
TRIM 264 LCC BODY
TRIM 264 CF8M BODY
TRIM 264 CF8M BODY

TRIM 264 WCC BODY
TRIM 264 LCC BODY
2000
TRIM 263
1000 TRIM 263
1500
TRIM 262
1000
50
TRIM 262
500
0 0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F
WITH STD TRIM 260, 262, 263, 264 WITH STD TRIM 260, 262, 263, 264
7000
9000
STD, SHUTOFF dP
STD, SHUTOFF dP
6000 8000
PRESSURE DROP, PSI
PRESSURE DROP, PSI
7000
5000
6000
TRIM 260. 264 WC9 BODY
4000
TRIM 260. 264 WC9 BODY

5000
STD, FLOWING dP
TRIM 264 WCC BODY

TRIM 263
TRIM 264 WCC BODY
TRIM 264 LCC BODY
TRIM 264 CF8M BODY

TRIM 264 LCC BODY
TRIM 264 CF8M BODY
3000 4000
STD, FLOWING dP
TRIM 263
3000
2000 TRIM 262
TRIM 262 2000
1000
1000
0 0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
LIMITS FOR NPS 3 CL2500 HPS

WITH STD TRIM 360S, 362S, 363S, 364S, 365S
4000
STD, SHUTOFF dP
3500
PRESSURE DROP, PSI
3000
TRIM 360S & 364S WCC BODY
TRIM 360S & 364S LCC BODY
TRIM 364S CF8M BODY &
2500
TRIM 364S WC9 BODY
STD, FLOWING dP
2000
365S CF8C BODY
1500
1000
TRIM 363S
TRIM 362S
500
0
0 200 400 600 800 1000 1200
FLUID TEMPERATURE, _F
37
Product Bulletin
51.2:HP HP Valve
Figure 18. Pressure-Temperature Limits for Cavitrol III Cage (also refer to table 7)
WITH CAV III TRIM 275, 276 WITH CAV III TRIM 275, 276
2500
4000
CAV III SHUTOFF dP, CAV III SHUTOFF dP
3−STAGE FLOWING dP 3500
2000 3−STAGE
PRESSURE DROP, PSI
PRESSURE DROP, PSI

FLOWING dP
TRIM 275, 276 WITH CF8M BODY

3000
1500 2500
2−STAGE
FLOWING dP 2000
WCC OR WC9 BODY

WCC OR WC9 BODY
TRIM 275, 276 WITH

TRIM 275, 276 WITH
WITH LCC BODY

WITH LCC BODY
1000
TRIM 275, 276

1500 2−STAGE
TRIM 275, 276
FLOWING dP
1000
50
500
0 0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
WITH CAV III TRIM 275, 276 WITH CAV III TRIM 275, 276
7000
9000
CAV III SHUTOFF dP
CAV III SHUTOFF dP
6000 8000
PRESSURE DROP, PSI
PRESSURE DROP, PSI
7000

5000
6000
4000
3−STAGE 5000
FLOWING dP
WCC OR WC9 BODY
WCC OR WC9 BODY

TRIM 275, 276 WITH
TRIM 275, 276 WITH

3000 4000
3−STAGE
WITH LCC BODY
WITH LCC BODY

FLOWING dP
TRIM 275, 276
TRIM 275, 276
3000
2000 2−STAGE
2−STAGE
FLOWING dP 2000
FLOWING dP
1000
1000
0 0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
38
Product Bulletin
HP Valve 51.2:HP
Figure 19. Pressure-Temperature Limits for Whisper III A, B, C Cage (also refer to table 7)
WITH WHISPER III LEVEL A, B, C TRIM 286A, 287, 288, 289 WITH WHISPER III LEVEL A, B, C TRIM 286A, 287, 288, 289
2500 4000
WIII SHUTOFF dP WIII SHUTOFF dP
WIII A, B, C, WIII A, B, C,
3500
FLOWING dP FLOWING dP
2000
PRESSURE DROP, PSI
PRESSURE DROP, PSI

3000
TRIM 288 WITH C12A BODY

TRIM 287 WITH WC9 BODY

2500

1500
WCC OR WC9 BODY

2000
WCC OR WC9 BODY
WITH LCC BODY

WITH LCC BODY
TRIM 286A WITH

TRIM 286A WITH
TRIM 289
1000 1500
TRIM 289
TRIM 286A
TRIM 286A
1000
50
500
0
0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
WITH WHISPER III LEVEL A, B, C TRIM 286A, 287, 288, 289 WITH WHISPER III LEVEL A, B, C TRIM 286A, 287, 288, 289
7000 9000
WIII SHUTOFF dP
WIII SHUTOFF dP
WIII A, B, C, 8000
6000 FLOWING dP
7000
PRESSURE DROP, PSI
PRESSURE DROP, PSI
WIII A, B, C,
5000 6000 FLOWING dP

4000 5000
WCC OR WC9 BODY

WCC OR WC9 BODY
4000
WITH LCC BODY
TRIM 286A WITH

3000
WITH LCC BODY
TRIM 286A WITH
3000
TRIM 289
TRIM 289
2000 TRIM 286A

TRIM 286A
2000
1000 1000
0
0 0 400 600 800 1000 1200
200
0 200 400 600 800 1000 1200
LIMITS FOR NPS 3 CL2500 HPS

WITH WHISPER III LEVEL A, B, C TRIM 307S, 387S, 388S, 389S
4000
WIII SHUTOFF &
FLOWING dP 1” STEM
3500
PRESSURE DROP, PSI
3000
2500
TRIM 388S WITH C12A BODY
TRIM 387S WITH WC9 BODY
WIII SHUTOFF &

FLOWING dP 3/4” STEM
2000
TRIM 389S
WCC OR WC9 BODY
1500
TRIM 307S WITH
1000
500
0
0 200 400 600 800 1000 1200
39
Product Bulletin
51.2:HP HP Valve
Figure 20. Pressure-Temperature Limits for Whisper III D Cage (also refer to table 7)
WITH WHISPER III LEVEL D TRIM 286A, 287, 288, 289 WITH WHISPER III LEVEL D TRIM 286A, 287, 288, 289
2500
4000 WIII SHUTOFF dP,
WIII SHUTOFF dP,
WIII D FLOWING dP WIII D TRIM 286A,
3500 289 FLOWING dP
2000
PRESSURE DROP, PSI
PRESSURE DROP, PSI

3000
WIII D TRIM

287, 288


1500 2500
FLOWING dP
WCC OR WC9 BODY

WCC OR WC9 BODY
2000
TRIM 289
WITH LCC BODY
WITH LCC BODY
TRIM 286A WITH

TRIM 289
TRIM 286A WITH
1000
1500
TRIM 286A
TRIM 286A
1000
50
500
0
0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
WITH WHISPER III LEVEL D TRIM 286A, 287, 288, 289 WITH WHISPER III LEVEL D TRIM 286A, 287, 288, 289
7000 9000
WIII SHUTOFF dP, WIII SHUTOFF dP
WIII D TRIM 286A, 8000
6000 289 FLOWING dP
7000 WIII D TRIM
PRESSURE DROP, PSI
PRESSURE DROP, PSI
5000 286A, 289

6000 FLOWING dP
WIII D TRIM 287,

4000 288 FLOWING dP 5000

WIII D TRIM
WCC OR WC9 BODY

WCC OR WC9 BODY
4000 287, 288

3000
WITH LCC BODY
WITH LCC BODY
TRIM 286A WITH

TRIM 286A WITH
FLOWING dP
TRIM 289
3000
TRIM 289
2000
TRIM 286A
TRIM 286A
2000
1000
1000
0 0
0 200 400 600 800 1000 1200
0 200 400 600 800 1000 1200
LIMITS FOR NPS 3 CL2500 HPS LIMITS FOR NPS 4 CL2500 HPS
WITH WHISPER III LEVEL D TRIM 307S, 387S, 388S, 389S WITH WHISPER III LEVEL D TRIM 307S, 387S, 388S, 389S
4000 4000 WIII D3 SHUTOFF &
WIII D3 SHUTOFF & FLOWING dP 1” STEM
3500 3500
FLOWING dP 1” STEM
WIII D3
3000 3000
SHUTOFF &
PRESSURE DROP, PSI
PRESSURE DROP, PSI
FLOWING
2500
2500 dP 3/4”
STEM WIII D3 SHUTOFF &

FLOWING dP 3/4” STEM
2000 2000
WCC OR WC9 BODY
WCC OR WC9 BODY

TRIM 307S WITH
1500
TRIM 307S WITH
1500
1000 1000
TRIM 389S
TRIM 389S
500 500
0 0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200
40
Product Bulletin
HP Valve 51.2:HP
Table 15. Globe Valve Dimensions with Table 16. Globe Valve Dimensions with
Standard/Style 1 Extension Bonnet Standard/Style 1 Extension Bonnet
A(1) B(1)
VALVE ASME EN VALVE ASME EN
SIZE, SIZE,
NPS CL900 CL1500 NPS CL900 CL1500
PN160 PN250 PN160 PN250
RF RTJ BWE SWE RF RTJ RF RTJ BWE SWE RF RTJ
mm mm
1 292 292 292 292 292 292 269 277 1 146 146 146 146 146 146 134 138
2 375 378 375 375 375 378 344 360 2 187 189 187 187 187 189 172 180
3 442 445 460 --- 460 464 442 460 3 221 222 230 --- 230 232 192 202
4x3 460 463 460 --- 479 482 --- --- 4x3 212 214 209 --- 222 223 --- ---
4 511 514 530 --- 530 533 511 530 4 229 230 238 --- 238 240 218 232
6x4 544 547 530 --- 598 604 --- --- 6x4 249 250 238 --- 276 279 --- ---
6 714 718 768 --- 768 775 714 768 6 310 311 337 --- 337 340 298 316
8x6 730 733 768 --- 787 797 --- --- 8x6 317 319 336 --- 345 350 --- ---
CL2500 CL2500
1 --- --- 318 318 318 318 --- --- 1 --- --- 159 159 159 159 --- ---
2 --- --- 400 400 413 416 --- --- 2 --- --- 200 200 206 208 --- ---
CL900 CL1500 PN160 PN250 CL900 CL1500 PN160 PN250
Inches Inches
1 11.50 11.50 11.50 11.50 11.50 11.50 10.58 10.90 1 5.75 5.75 5.75 5.75 5.75 5.75 5.29 5.45
2 14.75 14.88 14.75 14.75 14.75 14.88 13.56 14.18 2 7.38 7.44 7.38 7.38 7.38 7.44 6.78 7.09
3 17.38 17.50 18.12 --- 18.12 18.25 17.38 18.12 3 8.69 8.75 9.06 --- 9.06 9.12 7.54 7.94
4x3 18.12 18.25 18.12 --- 18.88 19.00 --- --- 4x3 8.38 8.44 8.25 --- 8.75 8.81 --- ---
4 20.12 20.25 20.88 --- 20.88 21.00 20.12 20.88 4 9.00 9.06 9.38 --- 9.38 9.44 10.75 9.13
6x4 21.44 21.56 20.88 --- 23.56 23.81 --- --- 6x4 9.81 9.88 9.38 --- 10.88 11.00 --- ---
6 28.12 28.25 30.25 --- 30.25 30.50 28.12 30.25 6 12.19 12.25 13.25 --- 13.25 13.38 11.72 12.43
8x6 28.75 28.88 30.25 --- 31.00 31.38 --- --- 8x6 12.5 12.56 13.25 --- 13.62 13.81 --- ---
CL2500 CL2500
1 --- --- 12.50 12.50 12.50 12.50 --- --- 1 --- --- 6.25 6.25 6.25 6.25 --- ---
2 --- --- 15.75 15.75 16.25 16.38 --- --- 2 --- --- 7.88 7.88 8.12 8.19 --- ---
1. RF-raised-face flanges; RTJ-ring-type joint flanges; BWE-buttweld ends; 1. RF-raised-face flanges; RTJ-ring-type joint flanges; BWE-buttweld ends;
SWE-socketweld ends. SWE-socketweld ends.
41
Product Bulletin
51.2:HP HP Valve
Table 17. Globe Valve Dimensions Table 18. Globe Valve Dimensions
with Standard Bonnet with Extension Bonnet
STANDARD BONNETS EXTENSION BONNETS (CL900 AND 1500)
D D
VALVE VALVE
Yoke Boss Diameters, mm (Inches) Yoke Boss Diameters, mm (Inches)
SIZE, G SIZE, G
NPS 127 NPS 127
71 (2-13/16) 90 (3-9/16) 71 (2-13/16) 90 (3-9/16)
(5) (5)
mm mm
CL900 and 1500 1 52 384 400 ---
1 52 260 267 --- 2 Std,
2 Std, Whisper III, 77 430 446 505
Whisper III, 77 261 267 331 Cavitrol III 3-Stage
Cavitrol III 3-Stage 2, Cavitrol III 2-Stage 77 448 464 518
2, Cavitrol III 2-Stage 77 279 286 344 Inches
4x3, 3 121 322 311 370 1 2.06 15.12 15.75 ---
6x4, 4 (long)(1) 175 --- 300 368 2 Std,
8x6, 6 (long)(1) 248 --- 365 402 Whisper III, 3.06 16.94 17.56 19.88
Cavitrol III 3-Stage
CL2500
1 63 35 35 --- 2, Cavitrol III 2-Stage 3.06 17.62 18.25 20.38
2 Std,
Whisper III, 84 303 303 352
2, Cavitrol III 2-Stage 84 320 320 40
Inches
CL900 and 1500
1 2.06 10.25 10.50 ---
2 Std,
Whisper III, 3.06 10.31 10.56 13.06
2, Cavitrol III 2-Stage 3.06 11.00 11.25 13.56
4x3, 3 4.75 12.69 12.25 14.56
6x4, 4 (long)(1) 6.88 --- 11.81 14.50
8x6, 6 (long)(1) 9.75 --- 14.38 15.81
CL2500
1 2.47 10.07 10.07 ---
2 Std,
Whisper III, 3.31 11.91 11.91 13.85
2, Cavitrol III 2-Stage 3.31 12.59 12.59 14.53
42
Product Bulletin
HP Valve 51.2:HP
Table 19. Globe Valve Dimensions A and

B with Standard Bonnet VALVE A
A SIZE, CL2500 CL3200
VALVE
SIZE, CL900 CL1500 NPS RF RTJ BWE RF RTJ BWE
NPS RF RTJ BWE RF RTJ BWE mm
mm 3 498 504 381 --- --- ---
4 (short)(1) 464 467 406 483 486 406 4 575 585 457 --- --- ---
6 (short)(1) 600 603 559 692 698 559 6 819 832 610 --- --- ---
8 781 784 653 838 848 685 8 1022 1038 762 --- --- 840
10 864 867 762 991 1001 822 10 1270 1292 1016 --- --- 1016
12 1016 1019 914 1130 1146 989 12 1321 1343 1118 --- --- 1118
Inches 14 --- --- 1300 --- --- ---
4 (short)(1) 18.27 18.39 15.98 19.02 19.13 15.98 Inches
6 (short)(1) 23.62 23.74 22.01 27.24 27.48 22.01 3 19.61 19.84 15.00 --- --- ---
8 30.75 30.87 25.71 32.99 33.39 26.97 4 22.64 23.03 17.99 --- --- ---
10 34.02 34.13 30.00 39.02 39.41 32.36 6 32.24 32.76 24.02 --- --- ---
12 40.00 40.12 35.98 44.49 45.12 38.94 8 40.24 40.87 30.00 --- --- 33.07
VALVE B 10 50.00 50.87 40.00 --- --- 40.00

SIZE, CL900 CL1500 12 52.01 52.87 44.02 --- --- 44.02
NPS RF RTJ BWE RF RTJ BWE 14 --- --- 51.18 --- --- ---
mm VALVE B
4 (short)(1) 232 233.5 203 241.5 243 203 SIZE, CL2500 CL3200
6 (short)(1) 300 301.5 282 340 343 282 NPS RF RTJ BWE RF RTJ BWE
8 402.0 403.5 349.0 431.0 436.0 370.0 mm
10 457.5 459.0 406.5 521.0 526.0 436.5 3 249 252 190.5 --- --- ---
12 559.0 560.5 503.0 616.0 624.0 536.0 4 290 295 228.5 --- --- ---
Inches 6 422 428.5 317.7 --- --- ---
4 (short)(1) 9.13 9.2 8 9.51 9.6 8 8 530.0 538.0 393.0 --- --- 435.0
6 (short)(1) 11.81 11.9 11.1 13.39 13.5 11.1 10 685.8 696.8 559.0 --- --- 526.0
8 15.83 15.89 13.74 16.97 17.17 14.57 12 694.8 705.8 575.0 --- --- 575.0
10 18.01 18.07 16.00 20.51 20.71 17.19 14 --- --- 680 --- --- ---
12 22.01 22.07 19.80 24.25 24.57 21.10 Inches
1. (Short) indicates industry standard short face-to-face. 3 9.8 9.92 7.5 --- --- ---
4 11.42 11.61 9 --- --- ---
6 16.61 16.87 12.5 --- --- ---
8 20.87 21.18 15.47 --- --- 17.13
10 27.00 27.43 22.01 --- --- 20.71
12 27.35 27.79 22.64 --- --- 22.64
14 --- --- 26.77 --- --- ---
43
Product Bulletin
51.2:HP HP Valve
Table 20. Globe Valve Dimensions G and D with Standard Bonnet

D
VALVE Yoke Boss Diameters, mm (inch)
G
SIZE,
NPS 90 (3 9/16) 127 (5)
CL900 CL1500 CL2500 CL3200 CL900 CL1500 CL2500 CL900 CL1500 CL2500
mm
3 --- --- 120.4 --- --- --- 401 --- --- 439
4 (short)(1) 102.8 102.8 136.8 --- 379 405 430 417 443 468
6 (short)(1) 130.9 141.1 204.7 --- 392 411 475 479 524 475
8 259.6 281.0 314.2 311.2 --- --- --- 547.1 547.1 ---
10 312.5 332.0 370 390 --- --- --- 556.2 565 ---
12 355 377.1 418.0 408 --- --- --- 618.3 653.1 ---
14 --- --- 397 --- --- --- --- --- --- ---
Inches
3 --- --- 4.74 --- --- --- 15.77 --- --- 17.27
4 (short)(1) 4.05 4.05 5.39 --- 14.92 15.95 16.93 16.42 17.45 18.42
6 (short)(1) 5.15 5.56 8.06 --- 15.42 16.17 18.7 18.87 20.63 18.7
8 10.22 11.06 12.37 12.25 --- --- --- 21.54 21.54 ---
10 12.30 13.07 14.57 15.35 --- --- --- 21.9 22.24 ---
12 13.98 14.85 16.46 16.06 --- --- --- 24.34 25.71 ---
14 --- --- 15.63 --- --- --- --- --- --- ---
D
VALVE Yoke Boss Diameters, mm (inch)
SIZE,
NPS 127 (5H) 178 (7)
CL900 CL1500 CL2500 CL3200 CL900 CL1500 CL2500 CL3200
mm
3 --- --- --- --- --- --- --- ---
4 (short)(1) --- --- --- --- --- --- --- ---
6 (short)(1) 479 524 475 --- --- --- --- ---
8 547.1 547.1 620 --- --- --- 620 647.3
10 556.2 565 647.4 --- --- --- 647.4 734.3
12 618.3 653.1 662.7 745.8 --- 653.1 662.7 745.8
14 --- --- 747 --- --- --- 747 ---
Inches
3 --- --- --- --- --- --- 12.17 ---
4 (short)(1) --- --- --- --- --- --- 19.33 ---
6 (short)(1) 18.87 20.63 18.7 --- --- --- 18.58 ---
8 21.54 21.54 24.41 --- --- --- 24.41 25.48
10 21.9 22.24 25.49 --- --- --- 25.49 28.91
12 24.34 25.71 26.09 29.36 --- 25.71 26.09 29.36
14 --- --- 29.41 --- --- --- 29.45 ---
1. (Short) indicates industry standard short face-to-face.
44
Product Bulletin
HP Valve 51.2:HP
Figure 21. Globe Valve Dimensions with Standard Bonnet (also see tables 15, 16, 17, and 18)
MATCH LINE FOR MATCH LINE FOR MATCH LINE FOR 585C SERIES
ACTUATOR ACTUATOR ACTUATORS AND TYPE 657,
667 SIZE 100 ACTUATORS
MATCH LINE FOR

ALL OTHER
ACTUATORS 25.4
(1.00)
mm
(INCHES)
FLANGED VALVE WITH 71 OR 90 mm BUTTWELD END VALVE WITH 71 OR 90 mm 127mm (5-INCH) DIAMETER YOKE BOSS
(2-13/16 OR 3-9/16 INCH) (2-13/16 OR 3-9/16 INCH) FOR USE WITH ALL
DIAMETER YOKE BOSS DIAMETER YOKE BOSS VALVES
A5700A-3
TYPICAL NPS 1, 2, AND 3
MATCH LINE FOR MATCH LINE FOR

ACTUATOR ACTUATOR
MATCH LINE FOR 585C SERIES

ACTUATORS AND TYPE 657,
667 SIZE 100 ACTUATORS
MATCH LINE FOR

ALL OTHER
ACTUATORS 25.4
(1.00)
FLANGED VALVE WITH 71 OR 90 mm BUTTWELD END VALVE WITH 71 OR 90 mm 127mm (5-INCH) DIAMETER YOKE BOSS
(2-13/16 OR 3-9/16 INCH) (2-13/16 OR 3-9/16 INCH) FOR USE WITH FLANGED OR
DIAMETER YOKE BOSS DIAMETER YOKE BOSS BUTTWELD VALVE
mm
A2719A-4 TYPICAL NPS 4, AND 6 (INCHES)
NOTE:
For dimensions of valves with other end connections, consult your Emerson sales office.
45
Product Bulletin
51.2:HP HP Valve
Figure 21. Globe Valve Dimensions with Standard Bonnet (also see tables 15, 16, 17, and 18) (continued)
MATCH LINE FOR

ACTUATOR MATCH LINE FOR
ACTUATOR
BUTTWELD END VALVE WITH 5H FLANGED VALVE WITH 5H

DIAMETER YOKE BOSS DIAMETER YOKE BOSS
TYPICAL NPS 8, 10, AND 12
NOTE:
For dimensions of valves with other end connections, consult your Emerson sales office.
Figure 22. Dimensions D for Style 1 Extension Bonnet

(A, B, and G Dimensions Listed in Figure 21 Do Not Change When Extension Bonnet is Used) (also see table 19)
MATCH LINE
FOR ACTUATOR
MATCH LINE FOR
585C SERIES ACTUATORS
MATCH LINE FOR ALL

OTHER ACTUATORS
25.4 D
(1.00)
D
127 mm (5-INCH) DIAMETER YOKE BOSS

FOR STYLE 1 EXTENSION BONNET
B
A
mm
FLANGED VALVE WITH STYLE 1 (INCHES)
EXTENSION BONNET HAVING 71 OR 90 mm
(2-13/16 OR 3-9/16 INCH)
DIAMETER YOKE BOSS
A5701A-2
46
Product Bulletin
HP Valve 51.2:HP
Table 21. Angle Valve Dimensions with Standard/Style 1 Extension Bonnet

STANDARD BONNETS
D
VALVE Yoke Boss Diameters, mm (Inches)
SIZE,
71 (2-13/16) 90 (3-9/16) 127 (5) 127 (5H)
NPS
CL900 and 1500 CL2500 CL900 and 1500 CL2500 CL900 and 1500 CL2500 CL900 and 1500 CL2500
mm
1 230 204 238 210 --- --- --- ---
2 Std,
Whisper III,
227 240 233 229 297 288 --- ---
Cavitrol III
3-Stage
2
Cavitrol III 244 257 251 246 314 305 --- ---
2-Stage
3 259 --- 265 --- 329 --- --- ---
4 289 --- 278 --- 337 --- --- ---
6 --- --- 300 396 368 434 --- ---
8 --- --- 364 414 401 414 --- 414
12 --- --- --- --- --- --- --- 516
Inches
1 9.06 8.04 9.38 8.28 --- --- --- ---
2 Std,
Whisper III,
8.94 9.45 9.19 9.00 11.69 11.32 --- ---
Cavitrol III
3-Stage
2
Cavitrol III 9.62 10.13 9.88 9.69 12.38 12.01 --- ---
2-Stage
3 10.19 --- 10.44 --- 12.94 --- --- ---
4 11.38 --- 10.94 --- 13.25 --- --- ---
6 --- --- 11.81 15.59 14.50 17.09 --- ---
8 --- --- 14.34 16.31 15.77 16.31 --- 16.31
12 --- --- --- --- --- --- --- 20.32
EXTENSION BONNETS
D
VALVE Yoke Boss Diameters, mm (Inches)
SIZE,
71 (2-13/16) 90 (3-9/16) 127 (5)
NPS
CL900 and 1500 CL2500 CL900 and 1500 CL2500 CL900 and 1500 CL2500
mm
1 354 373 371 388 --- ---
2 Std,
Whisper III, 395 --- 411 --- 470 ---
2
413 --- 429 --- 487 ---
Inches
1 13.94 14.67 14.62 15.28 --- ---
2 Std,
Whisper III, 15.56 --- 16.19 --- 18.50 ---
2
16.25 --- 16.88 --- 19.19 ---
47
Product Bulletin
51.2:HP HP Valve
Table 22. Angle Valve Dimensions with Standard/Style 1 Extension Bonnet

G A A & G(1)
VALVE ASME EN
SIZE,
NPS CL2500 CL900 CL1500
PN160 PN250
SWE SWE RF RTJ BWE SWE RF RTJ
mm
1 141 102 141 141 141 141 141 141 130 134
2 184 124 178 179 178 178 178 179 163 170
3 --- --- 226 227 235 --- 235 237 --- ---
4 --- --- 273 275 273 --- 273 275 --- ---
6 --- --- 325 327 353 --- 353 356 --- ---
8 --- --- 387 389 416 --- 416 421 --- ---
Inches
1 5.56 4.00 5.56 5.56 5.56 5.56 5.56 5.56 5.10 5.26
2 7.25 4.88 7.00 7.06 7.00 7.00 7.00 7.06 6.40 6.71
3 --- --- 8.88 8.94 9.25 --- 9.25 9.31 --- ---
4 --- --- 10.75 10.81 10.75 --- 10.75 10.81 --- ---
6 --- --- 12.81 12.88 13.88 --- 13.88 14.00 --- ---
8 --- --- 15.25 15.31 16.38 --- 16.38 16.56 --- ---
1. RF—raised-face flanges; RTJ—ring-type-joint flanges; BWE—buttweld ends; SWE—socketweld ends.
Figure 23. Angle Valve Dimensions with Standard/Style 1 Extension Bonnet (also see tables 21 and 22)
MATCH LINE
FOR ACTUATOR
MATCH LINE
FOR ACTUATOR
FLANGED VALVE WITH 71 OR 90 FLANGED VALVE WITH STYLE 1

mm (2-13/16 OR 3-9/16 INCH) EXTENSION BONNET HAVING 71 OR 90 mm
A6018A-1 DIAMETER YOKE BOSS (2-13/16 OR 3-9/16 INCH) DIAMETER YOKE BOSS
1 For CL900 and 1500 valves, G = A. For CL2500 valves, see table 22 for the G dimension.
Note: For dimensions of valves with other end connections, consult your Emerson sales office.
48
Product Bulletin
HP Valve 51.2:HP
49
Product Bulletin
51.2:HP HP Valve
50
Product Bulletin
HP Valve 51.2:HP
51
Product Bulletin
51.2:HP HP Valve
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher, FIELDVUE, WhisperFlo, Cavitrol, Whisper Trim, and ENVIRO-SEAL are marks owned by one of the companies in the Emerson Automation Solutions
business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric
Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Automation Solutions
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Cernay, 68700 France
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
E
521991, 2020 Fisher Controls International LLC. All rights reserved.

Product Bulletin Fisher HP Series Control Valves en 123584

Uploaded by

Copyright:

Available Formats

Product Bulletin Fisher HP Series Control Valves en 123584

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Bulletin Fisher HP Series Control Valves en 123584

Uploaded by

Copyright:

Available Formats

Product Bulletin

Fisher™ HP Series Control Valves

n Balanced Tight Shutoff Trim

Fisher HP Series control valves are single-port,

These valves are designed for high-pressure

HP Series valves have NACE compliant materials

Unless otherwise noted, all NACE references are to

Balanced HPT and HPAT

Maximum Inlet Pressure and Temperature(1,2) Flow Characteristics(4)

Figure 1. Fisher HPD Valve Assembly, NPS 2 to 6 Unbalanced Trim

Figure 2. Fisher HPD Valve Assembly, NPS 8 to 14

To help attenuate aerodynamic noise in gaseous

n Spiral-Wound Gaskets for Excellent Sealing Under

n Piping Economy—The availability of expanded end

n Quick Change Trim—Maintenance is simple and can

n Integrated Cage-Seat Ring Design—Find this option

n Standard Hard Trim Materials—The cage, valve plug,

n Increased Pressure/Temperature Ratings— HP Series

n Trim Interchangeability—Cavitrol III, Whisper Trim

n Control of Low Flow Rates/Tight

Features (cont.) In low-flow applications where cavitation damage

Features (cont.) NPS 8 through 12 HPD valves.

n High-Temperature Capability with Class V n Sour Service Trims Available—Long-lasting, erosion-

Table 1. Available Constructions

Table 2. Typical Flow Coefficients(1)

Table 4. Shutoff Classifications per ANSI/FCI 70-2 and IEC 60534-4

Material Selection pressure drop limits of the valve body-trim

1. Determine the pressure/temperature rating of the

Figure 6. Typical Balanced TSO Trim

Figure 7. ENVIRO-SEAL and HIGH-SEAL Packing Systems

TYPICAL HIGH-SEAL PACKING SYSTEM W8532-1

WITH GRAPHITE ULF PACKING TYPICAL ENVIRO-SEAL PACKING SYSTEM

TYPICAL ENVIRO-SEAL PACKING SYSTEM

Table 6. Approximate Weights (Valve and Bonnet Assemblies)

Figure 8. C-seal Trim

Figure 9. Bore Seal Trim

Table 9. Additional Globe Valve Specifications CL900 through CL1500

Table 9. Additional Globe Valve Specifications CL900 through CL1500 (continued)

Table 9. Additional Globe Valve Specifications CL900 through CL1500 (continued)

Table 9. Additional Globe Valve Specifications CL900 through CL1500 (continued)

Table 10. Globe Valve Specifications for CL2500 through CL3200

Table 12. Additional Angle Valve Specifications

Table 12. Additional Angle Valve Specifications (continued)

Table 12. Additional Angle Valve Specifications (continued)

n Trim 203— Trim 203 is the standard trim for

NPS 8 Angle Body Valve

With C-seal trim, a balanced valve can achieve

Table 13. Trim Descriptions

Table 13. Trim Descriptions (continued)

HP (NPS 8-14 CL900, CF8M, CF8C -198 to 316 -325 to 600

HP (NPS 8-14 CL900, CF8M, CF8C -198 to 316 -325 to 600

HP (NPS 3, 4, 6 CL900, CF8M, CF8C -198 to 316 -325 to 600

Table 13. Trim Descriptions (continued)

HP (NPS 3, 4, 6 CL900, WCC, WC9 -29 to 316 -20 to 600

Table 13. Trim Descriptions (continued)

Table 13. Trim Descriptions (continued)

Table 13. Trim Descriptions (continued)

HP (NPS 3, 4, 6 WCC, WC9 -29 to 316 -20 to 600

PRESSURE DROP, BAR, DIFFERENTIAL