Scribd
Upload
194 views

Pinout Esp32 Devkit v1

This document provides a pinout diagram for the DOIT ESP32 DEVKIT V1 development board. It identifies the functions of each physical pin on the board including positive supply pins, ground pins, GPIO pins, SPI pins, UART pins, I2C pins, touch inputs, DAC outputs, and control pins like EN and BOOT. It also notes some limitations and default configurations of the pins like GPIO pins 34-36 and 39 being input only and the builtin LED being connected to GPIO2.

Uploaded by

Daniel Ribeiro
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
194 views

Pinout Esp32 Devkit v1

This document provides a pinout diagram for the DOIT ESP32 DEVKIT V1 development board. It identifies the functions of each physical pin on the board including positive supply pins, ground pins, GPIO pins, SPI pins, UART pins, I2C pins, touch inputs, DAC outputs, and control pins like EN and BOOT. It also notes some limitations and default configurations of the pins like GPIO pins 34-36 and 39 being input only and the builtin LED being connected to GPIO2.

Uploaded by

Daniel Ribeiro
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

®

DOIT ESP32 DEVKIT V1 PINOUT CIRCUITSTATE WWW.CIRCUITSTATE.COM

D23
15 ENABLE 15 15 GPIO23 COPI 15

EN
C

D22
14 RTCIO0 A0 GPIX36 14 14 GPIO22 SCL 14

VP

D21 RX0 TX0


13 RTCIO3 A3 GPIX39 13

VN
13 GPIO1 TX0 13
ESP-WROOM-32

D34
12 RTCIO4 A6 GPIX34 12 12 GPIO3 RX0 12

D35
11 RTCIO5 A7 GPIX35 11 11 GPIO21 SDA 11
R 205 - 000519

D19
D32
10 RTCIO9 T9 A4 GPIO32 10 10 GPIO19 CIPO 10
FCC9D:2AC72-ESPWROOM32

D18
D33
9 RTCIO8 T8 A5 GPIO33 9 9 GPIO18 SCK 9

D25
8 RTCIO6 DAC1 A18 GPIO25 8 8 GPIO5 CS 8

D5
RX2 TX2
D26
7 RTCIO7 DAC2 A19 GPIO26 7 7 GPIO17 TX2 7

D27
6 RTCIO17 T7 A17 GPIO27 6 6 GPIO16 RX2 6

D14
5 RTCIO16 T6 A16 GPIO14 5 5 GPIO4 A10 T0 5

D4
POWER GPIO2

D12
4 RTCIO15 T5 A15 GPIO12 4 4 GPIO2 A12 T2 4

D2
3.3 H637PE
AMS1117
VIN GND D13

3V3 GND D15


3 RTCIO14 T4 A14 GPIO13 3 CP2102 3 GPIO15 A13 T3 3
DCL0CH
1437+
2 GND 2 2 GND 2

1 VIN 1 1 3.3V 1

BOOT
EN

• GPIO pins 34, 35, 36 and 39 are input only.


PHYSICAL PIN POSITIVE SUPPLY DAC OUTPUTS SPI PINS • TX0 and RX0 (Serial0) are used for serial programming.
• TX2 and RX2 can be accessed as Serial2.
CONTROL PINS GROUND SUPPLY TOUCH INPUTS UART PINS • Default SPI is VSPI. Both VSPI and HSPI pins can be set to any GPIO pins.
• All GPIO pins support PWM and interrupts.
GPIO PINS ADC INPUTS I2C PINS EXCLUDED PINS • Builtin LED is connected to GPIO2. Rev. 0.1, 17-12-2022
Design: Vishnu Mohanan
• Some GPIO pins are used for interfacing flash memory and thus are not shown. This work is licensed under a Creative Commons
Attribution 4.0 International License.

You might also like