Tevion 11ak52 SM

050-200320A
TOSHIBA
SERVICE MANUAL
COLOUR TELEVISION
28H37G
AK52 Chassis
PRINTED IN UK. 2002 C

SM52-DRX_IF
TABLE OF CONTENTS
1.INTRODUCTION.......................................................................................................................... 1
2.TUNER........................................................................................................................................ 1
3.IF PART (DRX 3960A) ................................................................................................................. 1
4.VIDEO SWITCH TEA6415............................................................................................................ 2
5.MULTI STANDARD SOUND PROCESSOR .................................................................................. 2
6.SOUND OUTPUT STAGE WITH TDA7480L ................................................................................. 2
7.VERTICAL OUTPUT STAGE WITH TDA8177F............................................................................. 2
8.VIDEO OUTPUT AMPLIFIER TDA6109........................................................................................ 2
9.POWER SUPPLY (SMPS)............................................................................................................ 3
10.MICROCONTROLLER SDA5550................................................................................................ 3
10.1.General Features................................................................................................................ 3
10.2.External Crystal and Programmable Clock Speed.............................................................. 3
10.3.Microcontroller Features.................................................................................................... 3
10.4.Memory .............................................................................................................................. 3
10.5.Display Features................................................................................................................. 3
10.6.ROM Characters................................................................................................................. 3
10.7.Acquisition Features.......................................................................................................... 4
10.8.Ports................................................................................................................................... 4
11.SERIAL ACCESS 32K EEPROM ................................................................................................ 4
12.CLASS AB STEREO HEADPHONE DRIVER TDA1308............................................................... 4
13.SAW FILTERS ........................................................................................................................... 4
14.IC DESCRIPTIONS .................................................................................................................... 4
14.1.TDA6109 ............................................................................................................................. 5
14.1.1.General Description ..................................................................................................... 5
14.1.2.Features....................................................................................................................... 5
14.1.3.Pinning......................................................................................................................... 5
14.2.27W401 ............................................................................................................................... 5
14.2.1.Description................................................................................................................... 5
14.2.2.Features....................................................................................................................... 5
14.2.3.Connections................................................................................................................. 6
14.3.24LC32A............................................................................................................................. 6
14.3.1.Description................................................................................................................... 6
14.3.2.Features....................................................................................................................... 6
14.3.3.Pin Descriptions........................................................................................................... 7
14.4.SDA5275............................................................................................................................. 7
14.4.1.Features....................................................................................................................... 7
14.4.2.Pin Definition and functions......................................................................................... 8
14.5.DRAM 4MX4........................................................................................................................ 9
14.5.2.Features....................................................................................................................... 9
14.5.3.Pin Assignment............................................................................................................ 9
14.6.SDA9400............................................................................................................................10
14.6.1.General Description ....................................................................................................10
14.6.2.Features......................................................................................................................10
14.6.3.Pin Definition ..............................................................................................................11
14.7.LM317T ..............................................................................................................................11
14.7.1.Description..................................................................................................................11
14.7.2.Features......................................................................................................................11
14.8.DDP3310............................................................................................................................12
14.8.1.Description..................................................................................................................12
14.8.2.Features......................................................................................................................12
14.8.3.Pin connection and short descriptions .......................................................................12
14.9.SDA5550............................................................................................................................14
14.9.1.General definition........................................................................................................14
14.9.2.Features......................................................................................................................14
14.10.TEA6415C........................................................................................................................15
14.10.1.General Description ..................................................................................................15
14.10.2.Features....................................................................................................................15
14.10.3.Pinning......................................................................................................................16
i
14.11.VPC3230D........................................................................................................................16
14.11.2.Pin Connections and Short Descriptions ..................................................................16
14.12.TDA1308T ........................................................................................................................18
14.12.2.Features....................................................................................................................18
14.12.3.Pinning......................................................................................................................18
14.13.MSP34X1G (MSP3411G) ..................................................................................................18
14.13.1.Description................................................................................................................18
14.13.2.Features....................................................................................................................19
14.13.3.Pin connections ........................................................................................................20
14.14.TL431...............................................................................................................................21
14.14.1.Description................................................................................................................21
14.14.2.Features....................................................................................................................21
14.14.3.Pin Configurations ....................................................................................................21
14.15.DRX3960A .......................................................................................................................22
14.15.1.Introduction...............................................................................................................22
14.15.2.Features....................................................................................................................22
14.15.3.Pin connection and short descriptions .....................................................................22
14.16.LM7808 ............................................................................................................................23
14.16.1.Description................................................................................................................23
14.16.2.Features....................................................................................................................23
14.17.BDX53BFI ........................................................................................................................23
14.17.1.Description................................................................................................................23
14.17.2.Applications..............................................................................................................23
14.18.TDA8177F ........................................................................................................................24
14.18.1.Description................................................................................................................24
14.18.2.Features....................................................................................................................24
14.18.3.Pin connections ........................................................................................................24
14.18.4.Block Diagram...........................................................................................................24
14.19.LM1086 ............................................................................................................................24
14.19.1.Description................................................................................................................24
14.19.2.Features....................................................................................................................24
14.19.3.Applications..............................................................................................................25
14.19.4.Connection Diagrams................................................................................................25
14.20.MC44608 ..........................................................................................................................25
14.20.1.Description................................................................................................................25
14.20.2.General Features.......................................................................................................25
14.20.3.Pin Connections........................................................................................................26
14.21.TCET1102G......................................................................................................................26
14.21.1.Description................................................................................................................26
14.21.2.Applications..............................................................................................................26
14.21.3.Features....................................................................................................................26
14.22.TDA7480L ........................................................................................................................27
14.22.1.Description................................................................................................................27
14.22.2.Features....................................................................................................................27
14.22.3.Pin Functions............................................................................................................27
14.23.SAA3010T ........................................................................................................................27
14.23.1.Description................................................................................................................27
14.23.2.Features....................................................................................................................28
14.23.3.Pinning......................................................................................................................28
15.AK52 CHASSIS MANUAL ADJUSTMENTS PROCEDURE ........................................................28
15.1.PRELIMINARY ...................................................................................................................28
15.2.SYSTEM VOLTAGE ADJUSTMENTS..................................................................................28
15.3.AFC ADJUSTMENTS .........................................................................................................28
15.4.FOCUS ADJUSTMENTS.....................................................................................................29
15.5.SCREEN ADJUSTMENTS ..................................................................................................29
15.6.IF ADJUSTMENT FOR L’ MODE.........................................................................................29
16.AK52 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS ............................................30
16.1.PRELIMINARY ...................................................................................................................30
16.2.H/V (HORIZONTAL AND VERTICAL GEOMETRY ALIGNMENTS).......................................30
ii
16.3.VIDEO ALIGNMENTS .........................................................................................................33
16.4.SERVICE ALIGNMENTS.....................................................................................................34
17.BLOCK DIAGRAM ....................................................................................................................36
18.CIRCUIT DIAGRAMS................................................................................................................37
iii
1.INTRODUCTION
11AK52 is a 100Hz flicker free colour television capable of driving 28”4:3/16:9, 32” 16:9, 33”4:3 and
29”4:3 real flat picture tubes.
The chassis is capable of operation in PAL, SECAM, NTSC (playback) colour standards and multiple
transmission standards as B/G, D/K, I/I’, and L/L´.
Sound system output is supplying 2x10W (10%THD) for left and right outputs of 8ohm speakers.
TV supports the level 1.5 teletext standard. It is possible to decode transmissions including high
graphical data.
The chassis is equipped with two full EuroScarts, one SCART for AV input/output, one front-AV input,
one back-AV input, one headphone output, one SVHS input (via SCART and SVHS connector), two
external speaker outputs (left and right).
2.TUNER
The hardware and software of the TV is suitable for tuners, supplied by different companies, which are
selected from the Service Menu. These tuners can be combined VHF, UHF tuners suitable for CCIR
2
systems B/G, H, L, L´, I/I´, and D/K. The tuning is available through the digitally controlled I C bus
(PLL). Below you will find info on one of the Tuners in use.
General description of UV1316:

The UV1316 tuner belongs to the UV 1300 family of tuners, which are designed to meet a wide range of
applications. It is a combined VHF, UHF tuner suitable for CCIR systems B/G, H, L, L’, I and I’. The low
IF output impedance has been designed for direct drive of a wide variety of SAW filters with sufficient
suppression of triple transient.
Features of UV1316:
1. Member of the UV1300 family small sized UHF/VHF tuners
2. Systems CCIR: B/G, H, L, L’, I and I’; OIRT: D/K
2
3. Digitally controlled (PLL) tuning via I C-bus
4. Off-air channels, S-cable channels and Hyperband
5. World standardized mechanical dimensions and world standard pinning
6. Compact size
7. Complies to “CENELEC EN55020” and “EN55013”
Pinning:
1. Gain control voltage (AGC) : 4.0V, Max: 4.5V
2. Tuning voltage
3. I²C-bus address select : Max: 5.5V
4. I²C-bus serial clock : Min:-0.3V, Max: 5.5V
5. I²C-bus serial data : Min:-0.3V, Max: 5.5V
6. Not connected
7. PLL supply voltage : 5.0V, Min: 4.75V, Max: 5.5V
8. ADC input
9. Tuner supply voltage : 33V, Min: 30V, Max: 35V
10. Symmetrical IF output 1
3.IF PART (DRX 3960A)

Tuner output IF signal is pre-filtered with only one 8-MHz channel SAW filter. The entire multistandard
processing is performed. The Digital Receiver Front-end DRX 3960A performs the entire multi-standard
Quasi Split Sound (QSS) TV IF processing, AGC, video demodulation, and generation of the second
sound IF (SIF). Video and tuner AGC is controlled and adjusted by take over voltage. The alignment-
free DRX 3960A needs no special external components. All control functions and status registers are
2
accessible via I C bus interface.
1
4.VIDEO SWITCH TEA6415
In case of three or more external sources are used, the video switch IC TEA6415 is used. The main
function of this device is to switch 8 video-input sources on the 6 outputs.
Each output can be switched on only one of each input. On each input an alignment of the lowest level
of the signal is made (bottom of sync. top for CVBS or black level for RGB signals).
Each nominal gain between any input and output is 6.5dB.For D2MAC or Chroma signal the alignment
is switched off by forcing, with an external resistor bridge, 5VDC on the input. Each input can be used
as a normal input or as a MAC or Chroma input (with external Resistor Bridge). All the switching
possibilities are changed through the BUS. Driving 75ohm load needs an external resistor. It is possible
to have the same input connected to several outputs.
5.MULTI STANDARD SOUND PROCESSOR

The MSP34x1G family of single-chip Multi-standard Sound Processors covers the sound processing of
all analog TV -Standards worldwide, as well as the NICAM digital sound standards. The full TV sound
processing, starting with analog sound IF signal-in, down to processed analog AF-out, is performed on
a single chip. Signal conforming to the standard by the Broadcast Television Systems Committee
(BTSC).
The DBX noise reduction, or alternatively, MICRONAS Noise Reduction (MNR) is performed alignment
free. Other processed standards are the Japanese FM-FM multiplex standard (EIA -J) and the FM
Stereo Radio standard.
6.SOUND OUTPUT STAGE WITH TDA7480L

The TDA7480L is an audio class-D amplifier assembled in Power DIP package specially designed for
high efficiency applications mainly for TV and Home Stereo sets.
Mute stand-by function of the audio amplifier can be described as the following; the pin 12
(MUTE/STAND-BY) controls the amplifier status by two different thresholds, referred to ground. When
Vpin 12 voltage is lower than 0.7V the amplifier is in Stand-by mode and the final stage generators are
off. When Vpin 12 is higher than 4V, the amplifier is in play mode.
The TDA7480L is a 10W+10W stereo sound amplifier with mute/stand-by facility. MUTE control signal
coming from microcontroller (when it is at high level) activates the mute function. IC is muted when
mute pin is at low level (pin12). MUTE pin can also be activated via an external pop-noise circuitry in
order to eliminate pop noise when TV is turned off. Just after the TV is turned off, this circuit switches
the IC to stand-by mode by pulling the mute pin voltage to ground.
7.VERTICAL OUTPUT STAGE WITH TDA8177F

The IC TDA8177F is the vertical deflection booster circuit. Two supply voltages, +12V and -12V are
needed to scan the inputs VERT+ and VERT-, respectively. And a third supply voltage, +60V for the
flyback limiting are needed. The vertical deflection coil is connected in series between the output and
feedback to the input.
8.VIDEO OUTPUT AMPLIFIER TDA6109

The TDA6109 includes three video output amplifiers in order to drive the three cathodes of a colour
picture tube directly. To obtain maximum performance, the amplifier is used with black-current control.
2
9.POWER SUPPLY (SMPS)
The DC voltages required at various parts of the chassis are provided by an SMPS transformer
controlled by the IC MC44608, which is designed for driving, controlling and protecting switching
transistor of SMPS. The transformer generates 135V for FBT input, +/-14V for audio amplifier, 8V stand
by voltage and 8V, 12V and 5V supplies for other different parts of the chassis.
An optocoupler is used to control the regulation of line voltage and stand-by power consumption. There
is a regulation circuit in secondary side. This circuit produces a control voltage according to the
changes in 135V DC voltage, via an optocoupler (TCET 1102G) to pin3 of the IC.
During the switch on period of the transistor, energy is stored in the transformer. During the switch off
period energy is fed to the load via secondary winding. By varying switch-on time of the power
transistor, it controls each portion of energy transferred to the second side such that the output voltage
remains nearly independent of load variations.
10.MICROCONTROLLER SDA5550
10.1.General Features
• Feature selection via special function register
• Simultaneous reception of TTX, VPS, PDC, and WSS (line 23)
• Supply Voltage 2.5 and 3.3 V
• ROM version is used.
10.2.External Crystal and Programmable Clock Speed
• Single external 6MHz crystal, all necessary clocks are generated internally
• CPU clock speed selectable via special function registers.
• Normal Mode 33.33 MHz CPU clock, Power Save mode 8.33 MHz
10.3.Microcontroller Features
• 8bit 8051 instruction set compatible CPU.
• 33.33-MHz internal clock (max.)
• 0.360 ms (min.) instruction cycle
• Two 16-bit timers
• Watchdog timer
• Capture compare timer for infrared remote control decoding
• Pulse width modulation unit (2 channels 14 bit, 6 channels 8 bit)
• ADC (4 channels, 8 bit)
• UART (rxd, txd)
10.4.Memory
• Up to 128 Kilobyte on Chip Program ROM
• Eight 16-bit data pointer registers (DPTR)
• 256-bytes on-chip Processor Internal RAM (IRAM)
• 128bytes extended stack memory.
• Display RAM and TXT/VPS/PDC/WSS-Acquisition-Buffer directly accessible via MOVX
• UP to 16KByte on Chip Extended RAM (XRAM) consisting of;
- 1 Kilobyte on-chip ACQ-buffer-RAM (access via MOVX)
- 1 Kilobyte on-chip extended-RAM (XRAM, access via MOVX) for user software
- 3 Kilobyte Display Memory
10.5.Display Features
• ROM Character set supports all East and West European Languages in single device
• Mosaic Graphic Character Set
• Parallel Display Attributes
• Single/Double Width/Height of Characters
• Variable Flash Rate
• Programmable Screen Size (25 Rows x 33...64 Columns)
• Flexible Character Matrixes (HxV) 12 x 9...16
• Up to 256 Dynamical Redefinable Characters in standard mode; 1024 Dynamical Redefinable
Characters in Enhanced Mode
• CLUT with up to 4096 colour combinations
• Up to 16 Colours per DRCS Character
• One out of 8 Colours for Foreground and Background Colours for 1-bit DRCS and ROM Characters
10.6.ROM Characters
• Shadowing
• Contrast Reduction
• Pixel by Pixel Shiftable Cursor With up to 4 Different Colours
• Support of Progressive Scan and 100 Hz.
3
• 3 X 4Bits RGB-DACs On-Chip
• Free Programmable Pixel Clock from 10 MHz to 32MHz
• Pixel Clock Independent from CPU Clock
• Multinorm H/V-Display Synchronization in Master or Slave Mode
10.7.Acquisition Features
• Multi-standard Digital Data Slicer
• Parallel Multi-norm Slicing (TTX, VPS, WSS, CC, G+)
• Four Different Framing Codes Available
• Data Caption only limited by available Memory
• Programmable VBI-buffer
• Full Channel Data Slicing Supported
• Fully Digital Signal Processing
• Noise Measurement and Controlled Noise Compensation
• Attenuation Measurement and Compensation
• Group Delay Measurement and Compensation
• Exact Decoding of Echo Disturbed Signals
10.8.Ports
2
• One 8-bit I/O-port with open drain output and optional I C Bus emulation support (Port0)
• Two 8-bit multifunction I/O-ports (Port1, Port3)
• One 4-bit port working as digital or analogue inputs for the ADC (Port2)
• One 2-bit I/O port with secondary function (P4.2, 4.3, 4.7)
• One 4-bit I/O-port with secondary function (P4.0, 4.1, 4.4) (Not available in P-SDIP 52)
11.SERIAL ACCESS 32K EEPROM

24LC32 is the 32Kbit electrically erasable programmable memory. The memory is compatible with the
2
I C standard, two wire serial interface, which uses a bi-directional data bus and serial clock.
12.CLASS AB STEREO HEADPHONE DRIVER TDA1308

The TDA1308 is an integrated class AB stereo headphone driver contained in a DIP8 plastic package.
The device is fabricated in a 1 mm CMOS process and has been primarily developed for portable digital
audio applications.
13.SAW FILTERS
X6966M is an 8-MHz SAW Filter which is used for pre-filtering the IF input signal of DRX 3960A. The
entire multistandard processing is performed within this filter which limits the signal bandwidth to 8 MHz
and suppresses major parts of the adjacent channels.
14.IC DESCRIPTIONS
TDA6109
27W401
24LC32
SDA5275
DRAM 4MX4
SDA9400
LM317T
DDP3310
SDA5550
TEA6415
VPC3230D
TDA1308T
MSP3411G
TL431
DRX3960A
LM7808
BDX53BFI
TDA8177F
LM1086
MC44608
TCET1102G
TDA7480L
SAA3010T
4
14.1.TDA6109
14.1.1.General Description
The TDA6109JF includes three video output amplifiers in one plastic DIL-bent-SIL 9-pin medium power
(DBS9MPF) package (SOT111-1), using high-voltage DMOS technology, and is intended to drive the three
cathodes of a colour CRT directly. To obtain maximum performance, the amplifier should be used with black-
current control.
14.1.2.Features
· Typical bandwidth of 9.0 MHz for an output signal of 60 V (p-p)
· High slew rate of 1850 V/ms
· No external components required
· Very simple application
· Single supply voltage of 200 V
· Internal reference voltage of 2.5 V
· Fixed gain of 51
· Black-Current Stabilization (BCS) circuit
· Thermal protection.
14.1.3.Pinning
SYMBOL PIN DESCRIPTION

Vi(1) 1 inverting input 1
GND 4 ground (fin)
Iom 5 black current measurement output
VDD 6 supply voltage
Voc(3) 7 cathode output 3
14.2.27W401
14.2.1.Description
The M27W401 is a low voltage 4 Mbit EPROM offered in the two ranges UV (ultra violet erase) and
OTP (one time programmable). It is ideally suited for microprocessor systems requiring large data or
program storage and is organized as 524,288 by 8 bits. The M27W401 operates in the read mode with
a supply voltage as low as 2.7V at –40 to 8??C temperature range. The decrease in operating power
allows either a reduction of the size of the battery or an increase in the time between battery re-
charges.
The FDIP32W (window ceramic frit-seal package) has a transparent lid, which allows the user to ex-
pose the chip to ultraviolet light to erase the bit pat-tern. A new pattern can then be written to the
device by following the programming procedure. For application where the content is programmed only
one time and erasure is not required, the M27W401 is offered in PDIP32, PLCC32 and TSOP32 (8 x 20
mm) packages.
14.2.2.Features
2.7V to 3.6v Low voltage in Read Operation
Access time:
–70ns at VCC = 3.0V to 3.6V
Pin Compatible with M27C4001
Low Power Consumption:
–1?mA max Standby Current
– 15mA max Active Current at 5MHz
Programming Time 10? ms/byte
High Reliability CMOS Technology
– 2,000V ESD Protection
– 200mA Latchup Protection Immunity
5
Electronic Signature
– Manufacturer Code: 20h
– Device Code: 41h
14.2.3.Connections
DIP connections LCC Connections TSOP Connections
Signal Names
A0-A18 Address Inputs
Q0-Q7 Data Outputs
E Chip Enable
G Output Enable
Vpp Program Supply
Vcc Supply Voltage
Vss Ground
14.3.24LC32A
14.3.1.Description
The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM
capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced,
low power applications such as personal communications or data acquisition. The 24LC32A also has a
page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential
reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the
same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range
make this device ideal for low-power/ low-voltage, nonvolatile code and data applications. The
24LC32A is available in the standard 8-pin plastic DIP and both 150 mil and 200 mil SOIC packaging.
14.3.2.Features
• Single supply with operation down to 2.5V
• Maximum write current 3 mA at 6.0V
• Standby current 1 mA max at 2.5V
• 2-wire serial interface bus, I 2 CÔ compatible
• 100 kHz (2.5V) and 400 kHz (5V) compatibility
• Self-timed ERASE and WRITE cycles
• Power on/off data protection circuitry
• Hardware write protect
• 1,000,000 Erase/Write cycles guaranteed
• 32 byte page or byte write modes available
6
• Schmitt trigger filtered inputs for noise suppression
• Output slope control to eliminate ground bounce
• 2 ms typical write cycle time, byte or page
• Up to eight devices may be connected to the same bus for up to 256K bits total memory
• Electrostatic discharge protection > 4000V
• Data retention > 200 years
• 8-pin PDIP and SOIC packages
• Temperature ranges
• Commercial (C): 0°C to +75°C
• Industrial (I): -40°C to +85°C
14.3.3.Pin Descriptions
A0, A1, A2 Chip Address Inputs
The A0..A2 inputs are used by the 24LC32A for multiple device operation and conform to the 2-wire bus
standard. The levels applied to these pins define the address block occupied by the device in the
address map. A particular device is selected by transmitting the corresponding bits (A2, A1, A0) in the
control byte.
SDA Serial Address/Data Input/Output

This is a Bi-directional pin used to transfer addresses and data into and data out of the device. It is an
open drain terminal, therefore the SDA bus requires a pull up resistor to VCC (typical 10 kO for 100 kHz,
2 kO for 400 kHz) For normal data transfer SDA is allowed to change only during SCL low. Changes
during SCL HIGH are reserved for indicating the START and STOP conditions.
SCL Serial Clock

This input is used to synchronize the data transfer from and to the device.
WP
This pin must be connected to either VSS or VCC. If tied to VSS, normal memory operation is enabled
(read/write the entire memory 000-FFF). If tied to VCC, WRITE operations are inhibited. The entire
memory will be write-protected. Read operations are not affected.
W CC
+2.5V to 6V Power Supply
W SS
Ground
14.4.SDA5275
14.4.1.Features
• Single chip teletext IC
• Analog CVBS-input with onchip clamping circuitry
• Slicer
• Supports level 1, 2.5 and 3.5 ETSI teletext standard
• Stores up to 14 teletext pages on chip
• Stores up to 2048 teletext pages with external 16 M memory
• SDA 5275: full level 2.5 processing
• Analog RGB-output
• 41 Latin script languages
• 12 ´ 10 character size
• Parallel display attributes
• 64 from 4096 colors selectable
• Enhanced flash modes
• Dynamically redefinable character set (DRCS, PCS)
• Pixel graphics
• Full screen display (64 ´ 32 or 80 ´ 24 character positions)
• Horizontal and vertical scrolling
• Graphic cursors
• 4:3 and 16:9 display
• Multinorm display (50/60/100/120 Hz)
• RISC-processor
• Firmware downloadable
2
• I C / 3 wire UART-interface (1 Mbit/s)
• Independent clocks for acquisition and display
7
• Tools for greatly simplified software development
• 24-Kbyte on-chip reconfigurable DRAM
• 44160-bit character ROM
• One external crystal for all standards
14.4.2.Pin Definition and functions
Pin No. P-LCC-68-1 Symbol Function

1 INTQ Interrupt request output to ext. controller
2 CLK-IO System clock input/output
3 TCSQ/FLD Composite sync output/ field output
4 VS/VCS Vertical sync input/output
5 HS Horizontal sync input/output
6 XOUT 20.5-MHz crystal oscillator output
7 XIN 20.5-MHz crystal oscillator input
8 GPO General purpose output
9 TM Test pin, leave open or connect VSS
10 CVBS CVBS-video signal input
11 VDD1 + 5 V digital supply
12 VDDA + 5 V analog supply
13 VSSA1 Analog ground
14 N.C. Not connected
17 RES Chip reset
23 VREF + 3 V reference voltage input
26 A8 External DRAM-address
38 RASQ Row address strobe (DRAM)
39 WEQ Write enable (DRAM)
40 D1 External DRAM-data
44 VSS4 0 V digital supply
45 CASQ Column address strobe
56 VBB Substrate bias voltage N.C.* (depends on version)
8
59 RGB-GND RGB-ground
61 R Analog red display output
62 G Analog green display output
63 B Analog blue display output
64 BLAN Blanking signal open drain output
65 CORQ Contrast reduction open drain output
66 SCL Bi-directional I2C Bus clock port
67 SDA Bi-directional I2C Bus data port
68 I2CEN I2C Bus enable
14.5.DRAM 4MX4
The 4 Meg x 4 DRAM is a randomly accessed, solid-state memory containing 16,777,216 bits
organized in a x4 con-figuration. RAS# is used to latch the row address (first 11 bits for 2K and first 12
bits for 4K). Once the page has been opened by RAS#, CAS# is used to latch the column address (the
latter 11 bits for 2K and the latter 10 bits for 4K, address pins A10 and A11 are “don’t care”). READ and
WRITE cycles are selected with the WE# input. A logic HIGH on WE# dictates READ mode, while a
logic LOW on WE# dictates WRITE mode. During a WRITE cycle, data-in (D) is latched by the falling
edge of WE# or CAS#, whichever occurs last. An EARLY WRITE occurs when WE# is taken LOW prior
to CAS# falling. A LATE WRITE or READ-MODIFY-WRITE occurs when WE# falls after CAS# is taken
LOW. During EARLY WRITE cycles, the data outputs (Q) will remain High-Z regardless of the state of
OE#. During LATE WRITE or READ-MODIFY-WRITE cycles, OE# must be taken HIGH to disable the
data outputs prior to applying input data. If a LATE WRITE or READ-MODIFY-WRITE is attempted
while keeping OE# LOW, no write will occur, and the data outputs will drive read data from the
accessed location. The four data inputs and the four data outputs are routed through four pins using
common I/O, and pin direction is controlled by WE# and OE#.
14.5.2.Features
• Industry-standard x4 pin out, timing, functions and packages
• State-of-the-art, high-performance, low-power CMOS silicon-gate process
• Single power supply (+3.3V ±0.3V or +5V ±10%)
• All inputs, outputs and clocks are TTL-compatible
• Refresh modes: RAS#-ONLY, HIDDEN and CAS#-BEFORE - RAS# (CBR)
• Optional Self Refresh (S) for low-power data retention
• 11 row, 11 column addresses (2K refresh) or 12 row, 10 column addresses (4K refresh)
• Extended Data-Out (EDO) PAGE MODE access cycle
• 5V-tolerant inputs and I/Os on 3.3V devices
14.5.3.Pin Assignment
Top View
*NC on 2K refresh and A11 on 4K refresh options. Note: The “#” symbol indicates signal is active LOW.
9
14.6.SDA9400
The SDA9400 is a new component of the Micronas MEGAVISION ® IC set in a 0.35µm embedded
DRAM technology (frame memory embedded). The SDA9400 is pin compatible to the SDA9401 (field
memory embedded). The SDA9400 comprises all main functionalities of a digital feature box in one
monolithic IC. The scan rate conversion to 100/120 Hz interlaced (50/60 Hz progressive) is based on a
motion adaptive algorithm. The scan rate converted picture can be vertically expanded. The SDA9400
has a free running mode, therefore features like scan rate conversion to e.g. 70, 75 Hz with joint lines or
multiple picture display (e.g. tuner scan) are possible. Due to the frame based signal processing, the
noise reduction has been greatly improved. Furthermore separate motion detectors for luminance and
chrominance have been implemented. For automatic controlling of the noise reduction parameters a
noise measurement algorithm is included, which measures the noise level in the picture or in the
blanking period. In addition a spatial noise reduction is implemented, which reduces the noise even in
the case of motion. The input signal can be compressed horizontally and vertically with a certain
number of factors. Therefore split screen is supported. Beside these additional functions like coloured
background, windowing and flashing are implemented.
14.6.2.Features
• Two input data formats
- 4:2:2 luminance and chrominance parallel (2 x 8 wires)
- ITU-R 656 data format (8 wires)
• Two different representations of input chrominance data
- 2‘s complement code
- Positive dual code
• Flexible input sync controller
• Flexible compression of the input signal
- Digital vertical compression of the input signal (1.0, 1.25, 1.5, 1.75, 2.0, 3.0, 4.0)
- Digital horizontal compression of the input signal (1.0, 2.0, 4.0)
• Noise reduction
- Motion adaptive spatial and temporal noise reduction (3D-NR)
- Temporal noise reduction for luminance frame based or field based
- Temporal noise reduction for chrominance field based
- Separate motion detectors for luminance and chrominance
- Flexible programming of the temporal noise reduction parameters
- Automatic measurement of the noise level (5-bit value, readable by I²C bus)
• 3-D motion detection
- High performance motion detector for scan rate conversion
- Global motion detection flag (readable by I²C bus)
- Movie mode and phase detector (readable by I²C bus)
• TV mode detection by counting line numbers (PAL, NTSC, readable by I²C bus)
• Embedded memory
- 5 Mbit embedded DRAM core for field memories
- 192 kbit embedded DRAM core for line memories
• Flexible clock and synchronization concept
- Decoupling of the input and output clock system possible
• Scan rate conversion
- Motion adaptive 100/120 Hz interlaced scan conversion
- Motion adaptive 50/60 Hz progressive scan conversion
- Simple static interlaced and progressive conversion modes for 100/120 Hz interlaced or 50/60 Hz
progressive scan conversion: e.g. ABAB, AABB, AA*B*B, AAAA, BBBB, AB, AA*
- Simple progressive scan conversion with joint lines:
50 Hz -> 60, 70, 75 Hz progressive
60 Hz -> 70, 75 Hz progressive
- Large area and line flicker reduction
• Flexible digital vertical expansion of the output signal (1.0, ... [1/32] ..., 2.0)
• Flexible output sync controller
- Flexible positioning of the output signal
- Flexible programming of the output sync raster
- External synchronization by backend IC possible
(e.g. split screen for one TV channel with joint lines and one PC VGA channel)
10
• Signal manipulations
- Insertion of coloured background
- Vertical and/or horizontal windowing with four different speed factors
- Flash generation (for supervising applications, motion flag readable by I²C bus)
- Still frame or field
- Support of split screen applications
- Multiple picture display - Tuner scan (4 and 16 times for 4:3, 12 times for 16:9 tubes)
- Support of multi picture display with PIP or front -end processor with integrated scaler
(e.g. 9 times display of PIP pictures, picture tracking, random pictures, still-in-moving picture, moving-
in-still picture)
• I²C-bus control (400 kHz)
• P-MQFP-64 package
• 3.3 V ± 5% supply voltage
14.6.3.Pin Definition
Pin No. Name Type Description

2,8,24,42,55 VSS1 S Supply voltage ( V SS = 0 V )
9,25,41,56 VDD1 S Supply voltage ( V DD = 3.3 V )
36,52,58 VSS2 S Supply voltage ( V SS = 0 V )
35,51,53,57,59 VDD2 S Supply voltage ( V DD = 3.3 V )
43,..,50 YIN0...7 I/TTL Data input Y (see input data format)
31,..,34;37,...,40 UVIN0...7 I/TTL Data input UV (for 4:2:2 parallel, see input data format)
PD (for CCIR 656, see input data format)
30 RESET I/TTL System reset. The RESET input is low active. In order to ensure
correct operation a "Power On Reset" must be performed. The
RESET pulse must have a minimum duration of two clock periods
of the system clock CLK1.
23 HIN I/TTL H-Sync input
PD (only for full CCIR 656)
22 VIN I/TTL V-Sync input
29 SYNCEN I/TTL Synchronization enable input
21 SDA I/O I2C-Bus data line (5V ability)
20 SCL I I I2C-Bus clock line (5V ability)
54 CLK1 I/TTL System clock 1
17,..,10 UVOUT0...7 O/TTL Data output UV (see output data format)
7,..,3;1;64;63 YOUT0...7 O/TTL Data output Y (see output data format)
62 HREF O/TTL Horizontal active video output
61 VOUT/ I/O/ EXSYN=0 (I²C-bus parameter): V-Sync output
VEXT TTL EXSYN=1: External V-Sync input for output part
60 HOUT/ I/O/ EXSYN=0 (I²C-bus parameter): H-Sync output
HEXT TTL EXSYN=1: External H-Sync input for output part
18 INTERLACED O/TTL Interlace signal for AC coupled vertical deflection
28 X1 / CLK2 I/TTL Crystal connection / System clock 2
27 X2 O/AN Crystal connection
26 CLKOUT O/TTL Clock output (depends on I²C parameters CLK11EN, CLK21EN,
FREQR)
19 TEST I/TTL Test input, connect to V SS for normal operation
14.7.LM317T
14.7.1.Description
The LM317T is an adjustable 3 terminal positive voltage regulator capable of supplying in excess of 1.5
amps over an output range of 1.25 to 37 volts. This voltage regulator is exceptionally easy to use and
requires only two external resistors to set the output voltage. Further, it employs internal current limiting,
thermal shutdown and safe area compensation, making it essentially blow–out proof. The LM317
serves a wide variety of applications including local, on card regulation. This device can also be used to
make a programmable output regulator, or by connecting a fixed resistor between the adjustment and
output, the LM317 can be used as a precision current regulator.
14.7.2.Features
• Output Current in Excess of 1.5 A
11
• Output Adjustable between 1.2 V and 37 V
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting Constant with Temperature
• Output Transistor Safe–Area Compensation
• Floating Operation for High Voltage Applications
2
• Available in Surface Mount D PAK, and Standard 3–Lead Transistor Package
• Eliminates Stocking many Fixed Voltages
14.8.DDP3310
14.8.1.Description
The DDP 3310B is a single-chip digital Display and Deflection Processor designed for high-quality
back-end applications in 100/120-Hz TV sets with 4:3 or 16:9 picture tubes. The IC can be combined
with members of the DIGIT 3000 IC family (VPC 32xx, TPU 3040), or it can be used with third-party
products. The IC contains the entire digital video component and deflection processing and all analog
interface components.
14.8.2.Features
Video processing
– linear horizontal scaling (0.25 … 4)
– non-linear horizontal scaling “panorama-vision”
– dynamic peaking
– soft limiter (gamma correction)
– color transient improvement
– programmable RGB matrix
– picture frame generator
– two analog RGB/Fast-Blank inputs. The DDP 3310B is a single-chip digital Display and Deflection
Processor designed for high-quality back-
Deflection processing
– scan velocity modulation output
– high-performance H/V deflection
– EHT compensation for vertical / East/West
– soft start/stop of H-Drive
– vertical angle and bow
– differential vertical output
– vertical zoom via deflection
– horizontal and vertical protection circuit
– adjustable horizontal frequency for VGA/SVGA display
Miscellaneous
– selectable 4:1:1/ 4:2:2 YC r C b input
– selectable 27/ 32-MHz line-locked clock input
– crystal oscillator for horizontal protection
– automatic picture tube adjustment (cutoff, white-drive)
– single 5-V power supply
– hardware for simple 50/60-Hz to 100/ 120-Hz conversion (display frequency doubling)
– two I2 C-controlled PWM outputs
– beam current limiter
14.8.3.Pin connection and short descriptions

NC = not connected LV = if not used, leave vacant
X = obligatory; connect as described in circuit diagram IN = Input
OUT = Output SUPPLY = Supply Pin
Pin no Pin name Type Connection Short description
PLCCK 68 pin (if not used)
1 VSUPP SUPPLY X Supply voltage, Output pin driver
2 GNDP SUPPLY X Ground, Output pin driver
3 VS2 IN GNDD Additional VSYNC input
4 FIFORRD OUT LV FIFO Read counter reset
12
5 FIFORD OUT LV FIFO Read Enable
6 FIFOWR OUT LV FIFO Write Enable
7 FIFORWR OUT LV FIFO Write counter reset
8 HOUT OUT X Horizontal Drive Output
9 HFLB IN Hout Horizontal Flyback Input
10 SAFETY IN GNDO Safety Input
11 VPROT IN GNDO Vertical protection Input
12 FREQSEL IN X Selection of H-Drive Frequency Range
13 CM1 IN X Clock select 40.5 or 27/32 MHz
14 CMO IN X Clock select 27/32 MHz
15 RSW2 OUT LV Range Switch2, Measurement ADC
16 RSW1 IN/OUT LV Range Switch1, Measurement ADC
17 SENSE IN GNDO Sense ADC Input
18 GNDM SUPPLY X Ground, MADC Input
19 VERT+ OUT GNDO Differantial Vertical Sawtooth Output
20 VERT- OUT GNDO Differantial Vertical Sawtooth Output
21 EW OUT GNDO Vertical Parabola Output
22 XREF IN X Reference Input for RGB DACs
23 SVM OUT VSUPO Scan Velocity Modulation
24 ROUT OUT VSUPO Analog Output Red
25 GOUT OUT VSUPO Analog Output Green
26 BOUT OUT VSUPO Analog Output Blue
27 GNDO SUPPLY X Ground, Analog Back-end
28 VSUPO SUPPLY X Supply Voltage, Analog Back-end
29 VRD/BCS IN X DAC Reference, Beam Current Safety
30 FBLIN1 IN GNDO Fast-Blank1 Input
31 RIN1 IN GNDO Analog Red1 Input
32 GIN1 IN GNDO Analog Green1 Input
33 BIN1 IN GNDO Analog Blue1 Input
38 TEST IN GNDD Test Pin
39 RESQ IN X Reset Input, active low
40 PWM1 OUT LV I2C-controlled DAC
42 HCS IN GNDD Half-contrast
43 C0 IN GNDD Picture Bas Chroma (LSB)
44 C1 IN GNDD Picture Bas Chroma
50 C7 IN GNDD Picture Bas Chroma (MSB)
51 VSUPD SUPPLY X Supply Voltage, Digital Circuitry
52 GNDD SUPPLY X Ground, Digital Circuitry
53 LLC2 IN X System Clock Input (27/32/40.5 MHz)
54 Y0 IN GNDD Picture Bas Luma (LSB)
55 Y1 IN GNDD Picture Bas Luma
61 Y7 IN GNDD Picture Bas Luma (MSB)
62 LLC1 IN VSUPD Single Line-Locked Clock Input (13.5/16 MHz)
63 HS IN X Horizontal Sync Input
64 VS IN GNDD Vertical Sync Input
65 XTALK2 OUT X Analog Crystal Output (5-MHz Security Clock)
66 XTALK1 IN X Analog Crystal Input (5-MHz Security Clock)
67 SDA IN/OUT X I2C-Bus Data
68 SCL IN/OUT X I2C-Bus Clock
13
14.9.SDA5550
14.9.1.General definition
The SDA5550M is a single chip teletext decoder for decoding World System Teletext data as well as
Video Programming System (VPS), Program Delivery Control (PDC), and Wide Screen Signalling
(WSS) data used for PAL plus transmissions (Line 23). The device provides an integrated general-
purpose, fully 8051-compatible Microcontroller with television specific hardware features.
Microcontroller has been enhanced to provide powerful features such as memory banking, data
pointers, and additional interrupts etc. The on-chip display unit for displaying Level 1.5 teletext data can
also be used for customer defined on screen displays. Internal XRAM consists of up to 17 Kbytes. This
device can support external memory up to 1Mbyte ROM and RAM.TVTEXT Controller contains a data
slicer for VPS, WSS, PDC and TXT, an acceleration acquisition hardware module, a display generator
for Level 1.5 TXT and powerful On screen Display capabilities based on parallel attributes, and pixel
oriented characters (DRCS). The 8 bit Microcontroller operates at 360nsec cycle time (min). Controller
with dedicated hardware does most of the internal TXT acquisition processing, transfer data to/from
2
external memory interface and receives/transmits data via I C-firmware user interface. SDA5550M is
realized in 0.25 micron technology with 2.5V supply voltage and 3.3V I/O compatible. The IC produces
the following input or output control signals; AGC_CON, MODE_SW, L / L’, PIP_MODS, PIP_SEL,
ON/OFF (stand-by), SC1..3_IN_AV (pin 8 information from 3 SCARTs), AFC, MUTE (to mute audio
2
output IC), I CEN.
14.9.2.Features
General
External Crystal and Programmable clock speed

Single external 6MHz crystal, all necessary clocks are generated internally
CPU clock speed selectable via special function registers.
Normal Mode 33.33 MHz CPU clock, Power Save mode 8.33 MHz
Microcontroller Features
• 0.360ms (min.) instruction cycle
• Watchdog timer
• UART
Memory
• Non-multiplexed 8-bit data and 16 … 20-bit address bus (ROMless Version)
• Memory banking up to 1Mbyte (Romless version)
Display Features
• ROM Character Set Supports all East and West European Languages in single device
14
• CLUT with up to 4096 color combinations
• Up to 16 Colors per DRCS Character
• One out of Eight Colors for Foreground and Background Colors for 1-bit DRCS and ROM Characters
• Shadowing
• Pixel by Pixel Shiftable Cursor With up to 4 Different Colors
Acquisition Features
• Multistandard Digital Data Slicer
• Data Caption only Limited by available Memory
Ports
2
• One 8-bit I/O-port with open drain output and optional I C Bus emulation support (Port 0)
• Two 8-bit multifunction I/O-ports (Port 1, Port 3)
• One 4-bit port working as digital or analog inputs for the ADC (Port 2)
• One 2-bit I/O port with secondary functions (P4.2, 4.3, 4.7)
14.10.TEA6415C
The main function of the IC is to switch 8 video input sources on 6 outputs. Each output can be
switched on only one of each input. On each input an alignment of the lowest level of the signal is made
(bottom of synch. top for CVBS or black level for RGB signals). Each nominal gain between any input
and output is 6.5dB. For D2MAC or Chroma signal the alignment is switched off by forcing, with an
external resistor bridge, 5 VDC on the input. Each input can be used as a normal input or as a MAC or
Chroma input (with external resistor bridge). All the switching possibilities are changed through the
BUS. Driving 75? load needs an external transistor. It is possible to have the same input connected to
several outputs. The starting configuration upon power on (power supply: 0 to 10V) is undetermined. In
this case, 6 words of 16 bits are necessary to determine one configuration. In other case, 1 word of 16
bits is necessary to determine one configuration.
14.10.2.Features
• 20MHz Bandwidth
• Cascadable with another TEA6415C (Internal address can be changed by pin 7 voltage)
• 8 Inputs (CVBS, RGB, MAC, CHROMA,...)
• 6 Outputs
• Possibility of MAC or chroma signal for each input by switching-off the clamp with an external resistor
bridge
• Bus controlled
• 6.5dB gain between any input and output
• 55dB crosstalk at 5mHz
15
• Fully ESD protected
14.10.3.Pinning
1. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
2. Data : Low level : -0.3V Max: 1.5V,
High level : 3.0V Max : Vcc+0.5V
4. Clock : Low level : -0.3V Max: 1.5V,
7. Prog
8. Input : Max : 2Vpp, Input Current: 1mA, Max: 3mA
9. Vcc : 12V
12. Ground
13. Output : 5.5Vpp, Min : 4.5Vpp
19. Ground
20. Input : Max : 2Vpp, Input Current : 1mA, Max : 3mA
14.11.VPC3230D
The VPC 323xD is a high-quality, single-chip video front-end, which is targeted for 4:3 and 16:9, 50/60-
Hz and 100/120 Hz TV sets. It can be combined with other members of the DIGIT3000 IC family (such
as DDP 331x) and/or it can be used with 3rd-party products. The main features of the VPC 323xD are;
– high-performance adaptive 4H comb filter Y/C separator with adjustable vertical peaking
– multi-standard color decoder PAL/NTSC/SECAM including all substandards
– four CVBS, one S-VHS input, one CVBS output
– two RGB/YC r C b component inputs, one Fast Blank (FB) input
– integrated high-quality A/D converters and associated clamp and AGC circuits
– multi-standard sync processing
– linear horizontal scaling (0.25 ... 4), as well as non-linear horizontal scaling ‘Panorama-vision’
– PAL+ preprocessing
– line-locked clock, data and sync, or 656-output interface
– peaking, contrast, brightness, color saturation and tint for RGB/ YC r C b and CVBS/ S-VHS
– high-quality soft mixer controlled by Fast Blank
– PIP processing for four picture sizes (1/4, 1/9, 1/16 or 1/36 of normal size) with 8-bit resolution
– 15 predefined PIP display configurations and expert mode (fully programmable)
– control interface for external field memory
– I2C-bus interface
– one 20.25-MHz crystal, few external components
– 80-pin PQFP package
14.11.2.Pin Connections and Short Descriptions

NC = not connected
LV = if not used, leave vacant
X = obligatory; connect as described in circuit diagram
SUPPLYA = 4.75...5.25 V, SUPPLYD = 3.15...3.45 V
Pin No. Pin Name Type Connection Short Description

PQFP (if not used)
80-pin
1 B1/CB1IN IN VREF Blue1/Cb1 Analog Component Input
2 G1/Y1IN IN VREF Green1/Y1 Analog Component Input
16
3 R1/CR1IN IN VREF Read1/Cr1 Analog Component Input
7 ASGF X Analog Shield GNDF
8 FFRSTWIN IN LV or GNDD FIFO Reset Write Input
9 VSUPCAP OUT X Digital Decoupling Circuitry Supply Voltage
10 VSUPD SUPPLYD X Supply Voltage, Digital Circuitry
11 GNDD SUPPLYD X Ground, Digital Circuitry
12 GNDCAP OUT X Digital Decoupling Circuitry GND
13 SCL IN/OUT X I2C Bus Clock
14 SDA IN/OUT X I2C Bus Data
15 RESQ IN X Reset Input, Active Low
16 TEST IN GNDD Test Pin, connect to GNDD
17 VGAV IN GNDD VGAV Input
18 YCOEQ IN GNDD Y/C Output Enable Input, Active Low
19 FFIE OUT LV FIFO Input Enable
20 FFWE OUT LV FIFO Write Enable
21 FFRSTW OUT LV FIFO Reset Write/Read
22 FFRE OUT LV FIFO Read Enable
23 FFOE OUT LV FIFO Output Enable
24 CLK20 IN/OUT LV Main Clock output 20.25 MHz
25 GNDPA OUT X Pad Decoupling Circuitry GND
26 VSUPPA OUT X Pad Decoupling Circuitry Supply Voltage
27 LLC2 OUT LV Double Clock Output
28 LLC1 IN/OUT LV Clock Output
29 VSUPLLC SUPPLYD X Supply Voltage, LLC Circuitry
30 GNDLLC SUPPLYD X Ground, LLC Circuitry
31 Y7 OUT GNDY Picture Bus Luma (MSB)
32 Y6 OUT GNDY Picture Bus Luma
35 GNDY SUPPLYD X Ground, Luma Output Circuitry
36 VSUPY SUPPLYD X Supply Voltage, Luma Output Circuitry
40 Y0 OUT GNDY Picture Bus Luma (LSB)
41 C7 OUT GNDC Picture Bus Chroma (MSB)
42 C6 OUT GNDC Picture Bus Chroma
45 VSUPC SUPPLYD X Supply Voltage, Chroma Output Circuitry
46 GNDC SUPPLYD X Ground, Chroma Output Circuitry
50 C0 OUT GNDC Picture Bus Chroma (LSB)
51 GNDSY SUPPLYD X Ground Sync Pad Circuitry
52 VSUPSY SUPPLYD X Supply Voltage, Sync Pad Circuitry
53 INTLC OUT LV Interlace Output
54 AVO OUT LV Active Video Output
55 FSY/HC/HSYA OUT LV Front Sync/ Horizontal Clamp Pulse/Front-End Horizontal
Sync Output
56 MSY/HS IN/OUT LV Main Sync/Horizontal Sync Pulse
57 VS OUT LV Vertical Sync Pulse
58 FPDAT/VSYA IN/OUT LV Front End/Back-End Data/Front-End Vertical Sync Output
59 VSTBYY SUPPLYA X Standby Supply Voltage
60 CLK5 OUT LV CCU 5 MHz Clock Output
61 NC - LV or GNDD Not Connected
62 XTAL1 IN X Analog Crystal Input
63 XTAL2 OUT X Analog Crystal Output
65 GNDF SUPPLYA X Ground, Analog Front-End
66 VRT OUTPUT X Reference Voltage Top, Analog
17
67 I2CSEL IN X I2C Bus Address Select
68 ISGND SUPPLYA X Signal Ground for Analog Input, connect to GNDF
69 VSUPF SUPPLYA X Supply Voltage, Analog Front-End
70 VOUT OUT LV Analog Video Output
71 CIN IN LV Chroma/Analog Video 5 Input
72 VIN1 IN VRT Video 1 Analog Input
76 VSUPAI SUPPLYA X Supply Voltage, Analog Component Inputs Front-End
77 GNDAI SUPPLYA X Ground, Analog Component Inputs Front-End
78 VREF OUTPUT X Reference Voltage Top, Analog Component Inputs Front-
End
79 FB1IN IN VREF Fast Blank Input
80 AISGND SUPPLYA X Signal Ground for Analog Component Inputs, connect to
GNDAI
14.12.TDA1308T
The TDA1308 is an integrated class AB stereo headphone driver contained in an SO8 or a DIP8 plastic
package. The device is fabricated in a 1 mm CMOS process and has been primarily developed for
portable digital audio applications. It gets its input from two analog audio outputs (DACA_L and
DACA_R) of MSP3411G. The gain of the output is adjustable by the feedback resistor between the
inputs and outputs.
14.12.2.Features
• Wide temperature range
• No switch ON/OFF clicks
• Excellent power supply ripple rejection
• Low power consumption
• Short-circuit resistant
• High performance
• high signal-to-noise ratio
• High slew rate
• Low distortion
• Large output voltage swing.
14.12.3.Pinning

OUTA 1 Output A
INA(neg) 2 Inverting input A
INA(pos) 3 Non-inverting input A
V SS 4 Negative supply
INB(pos) 5 Non-inverting input B
INB(neg) 6 Inverting input B
OUTB 7 Output B
V DD 8 Positive supply
14.13.MSP34X1G (MSP3411G)
14.13.1.Description
The MSP 34x1G family of single-chip Mullet-standard Sound Processors covers the sound processing
of all analog TV -Standards worldwide, as well as the NICAM digital sound standards. The full TV sound
a single chip. Figure shows a simplified functional block diagram of the MSP34x1G. The MSP34x1G
has all functions of the MSP34x0G with the addition of a virtual surround sound feature. Surround
sound can be reproduced to a certain extent with two loudspeakers. The MSP34x1G includes our
virtualizer algorithm “3D-PANORAMA” which has been approved by the Dolby 1) Laboratories for
compliance with the "Virtual Dolby Surround" technology. In addition, the MSP34x1G includes the
18
“PANORAMA” algorithm. These TV sound processing ICs include versions for processing the multi-
channel television sound (MTS) signal conforming to the standard recommended by the Broadcast
Television Systems Committee (BTSC). The DBX noise reduction, or alternatively, Micronas Noise
Reduction (MNR) is performed alignment free. Other processed standards are the Japanese FM-FM
multiplex standard (EIA -J) and the FM Stereo Radio standard. Current ICs have to perform adjustment
procedures in order to achieve good stereo separation for BTSC and EIA-J. The MSP34x1G has
optimum stereo performance without any adjustments. All MSP 34xxG versions are pin and software
downward compatible to the MSP 34xxD. MSP34x1G further simplifies controlling software. Standard
selection requires a singleI2 C transmission only. The MSP34x1G has built-in automatic functions: The
IC is able to detect the actual sound standard automatically (Automatic Standard Detection).
Furthermore, pilot levels and identification signals can be evaluated internally with subsequent
switching between mono/stereo/bilingual; no I2 C interaction is necessary (Automatic Sound Selection).
14.13.2.Features
3D-PANORAMA virtualizer (approved by Dolby Laboratories) with noise generator
PANORAMA virtualizer algorithm
Standard Selection with single I2C transmission
Automatic Standard Detection of terrestrial TV standards/Automatic Carrier Mute function
Automatic Sound Selection (mono/stereo/bilingual), new registers MODUS, STATUS
Two selectable sound IF (SIF) inputs
Interrupt output programmable (indicating status change)
Loudspeaker / Headphone channel with volume, balance, bass, treble, loudness
Loudspeaker channel with MDB (Micronas Dynamic Bass)
AVC: Automatic Volume Correction
Subwoofer output with programmable low-pass and complementary high-pass filter
5-band graphic equalizer for loudspeaker channel
Spatial effect for loudspeaker channel; processing of all deemphasis filtering
Four Stereo SCART (line) inputs, one Mono input; two Stereo SCART outputs
Complete SCART in/out switching matrix
2 2
Two I S inputs; one I S output
All analog FM-Stereo A2 and satellite standards
All analog Mono sound carriers including AM-SECAM L
Simultaneous demodulation of (very) high-deviation FM-Mono and NICAM
Adaptive deemphasis for satellite (Wegener-Panda, acc. to ASTRA specification)
ASTRA Digital Radio (ADR) together with DRP 3510A
All NICAM standards
Korean FM-Stereo A2 standard
19
14.13.3.Pin connections
NC = not connected; leave vacant
DVSS: if not used, connect to DVSS
AHVSS: connect to AHVSS
Connection
Pin No. Pin Name Type Short Description
(if not used)
PLCC PSDIP PSDIP PQFP PLQFP
68-pin 64-pin 52-pin 80-pin 64-pin
1 16 14 9 8 ADR_WS OUT LV ADR word strobe
2 - - - - NC LV Not connected
3 15 13 8 7 ADR_DA OUT LV ADR Data Output
4 14 12 7 6 I2S_DA_IN1 IN LV I2S1 data input
5 13 11 6 5 I2S_DA_OUT OUT LV I2S data output
6 12 10 5 4 I2S_WS IN/OUT LV I2S word strobe
7 11 9 4 3 I2S_CL IN/OUT LV I2S clock
8 10 8 3 2 I2C_DA IN/OUT X I2C data
9 9 7 2 1 I2C_CL IN/OUT X I2C data
10 8 - 1 64 NC LV Not connected
11 7 6 80 63 STANDBYQ IN X Stand-by (low -active)
12 6 5 79 62 ADR_SEL IN X I2C bus address select
13 5 4 78 61 D_CTR_I/O_0 IN/OUT LV D_CTR_I/O_0
Audio clock output
18 1 2 74 57 AUD_CL_OUT OUT LV
(18.432 MHz)
19 64 1 73 56 TP LV Test pin
20 63 52 72 55 XTAL_OUT OUT X Crystal oscillator
21 62 51 71 54 XTAL_IN IN X Crystal oscillator
22 61 50 70 53 TESTEN IN X Test pin
AVSS via 56 IF Input 2 (can be left
23 60 49 69 52 ANA_IN2+ IN pF/LV vacant, only if IF input 1 is
also not in use)
AVSS via 56 IF common (can be left
24 59 48 68 51 ANA_IN- IN vacant, only if IF input 1 is
pF/LV
also not in use)
25 58 47 67 50 ANA_IN1+ IN LV IF input 2
26 57 46 66 49 AVSUP X Analog power supply 5v
- - - 65 - AVSUP X Analog power supply 5v
- - - 64 - NC LV Not connected
- - - 63 48 NC LV Not connected
27 56 45 62 48 AVSS X Analog ground
- - - 61 - AVSS X Analog ground
28 55 44 60 47 MONO_IN IN LV Mono input
Reference voltage IF A/D
29 54 43 58 46 VREFTOP X
converter
30 53 42 57 45 SC1_IN_R IN LV SCART 1 input, right
31 52 41 56 44 SC1_IN_L IN LV SCART 1 input, left
32 51 - 55 43 ASG AHVSS Analog Shield Ground
39 44 - 48 36 SC4_IN_R IN LV SCART 4 input, right
40 43 - 47 35 SC4_IN_L IN LV SCART 4 input, left
41 - - 46 - NC LV or AHVSS Not connected
42 42 36 45 34 AGNDC X Analog reference voltage
43 41 35 44 33 AHVSS X Analog ground
- - - 43 - AHVSS X Analog ground
44 40 34 40 32 CAPL_M X Volume capacitor MAIN
45 39 33 39 31 AHVSUP X Analog power supply 8V
20
46 38 32 38 30 CAPL_A X Volume capacitor AUX
47 37 31 37 29 SC1_OUT_L OUT LV SCART output 1, left
48 36 30 36 28 SC1_OUT_R OUT LV SCART output 1, right
49 35 29 35 27 VREF X Reference ground 1
52 - - 32 - NC LV Not connected
54 31 26 30 23 DACM_SUB OUT LV Subwoofer output
56 29 25 28 21 DACM_L OUT LV Loudspeaker out, left
57 28 24 27 20 DACM_R OUT LV Loudspeaker out, right
58 27 23 26 19 VREF2 X Reference ground 2
59 26 22 25 18 DACA_L OUT LV Headphone out, left
60 25 21 24 17 DACA_R OUT LV Headphone out, right
61 24 20 21 16 RESETQ IN X Power-on-reset
64 21 19 18 13 NC LV Not connected
65 20 18 17 12 I2S_DA_IN2 IN LV I2S2-data input
66 19 17 16 11 DVSS X Digital ground
- - - 15 - DVSS X Digital ground
67 18 16 13 10 DVSUP X Digital power supply 5V
- - - 12 - DVSUP X Digital power supply 5V
68 17 15 10 9 ADR_CL OUT LV ADR clock
14.14.TL431
14.14.1.Description
The TL431 is a 3-terminal adjustable shunt voltage regulator providing a highly accurate 1 % band gap
reference. TL431 acts as an open-loop error amplifier with a 2.5V temperature compensation reference.
The TL431 thermal stability, wide operating current (150mA) and temperature range (0.to 105.makes it
suitable for all variety of application that are looking for a low cost solution with high performance. The
output voltage may be adjusted to any value between VREF and 36 volts with two external resistors.
The TL431 is operating in full industrial temperature range of 0°C to 105°C. The TL431 is available in
TO-92, SO-8, SOT-89 and SOT23-5 packages.
14.14.2.Features
• Trimmed Band gap to 1%
• Wide Operating Current 1mA to 150mA
• Extended Temperature Range 0. °C to 105.°C
• Low Temperature Coefficient 30 ppm /°C
• Offered in TO -92, SOIC, SOT-89, SOT-23-5
• Improved Replacement in Performance for TL431
• Low Cost Solution
14.14.3.Pin Configurations
21
14.15.DRX3960A
14.15.1.Introduction
The Digital Receiver Front -end DRX 3960A performs the entire multi-standard Quasi Split Sound (QSS)
TV IF processing, AGC, video demodulation, and generation of the second sound IF (SIF) with only one
SAW filter. The IC is designed for applications in TV sets, VCRs, PC cards, and TV tuners. The
alignment-free DRX 3960A needs no special external components. All control functions and status
registers are accessible via I2 C bus interface. Therefore, it simplifies the design of high-quality, highly
standardized IF stages. Due to its mixed signal structure and the digital demodulation, the IC offers
unique features and is prepared for digital TV.
14.15.2.Features
– Multi-standard QSS IF processing with a single SAW
– Highly reduced amount of external components (no tank circuit, no potentiometers, no SAW
switching)
– Programmable IF frequency (38.9 MHz, 45.75 MHz, 32.9 MHz, 36.125 MHz etc.)
– Digital IF processing for the following standards: B/G, D/K, I, L/L’, and M/N
– Standard specific digital post filtering
– Standard specific digital video/audio splitting
– Standard specific digital picture carrier recovery:
– alignment-free
– Quartz-stable and accurate
– Stable frequency lock at 100% modulation and over modulation up to 115%
– Quartz-accurate AFC information
– Programmable standard specific digital group delay equalizing
– Automatically frequency-adjusted Nyquist slope, therefore optimal picture and sound performance
over complete lock in frequency range
– Standard specific digital AGC and delayed tuner AGC with programmable tuner Take Over Point
– Fast AGC due to linear structure
– Adaptive back porch control, therefore fast positive modulation AGC
– No sound traps needed at video output
– Second SIF output with standard dependent pre-filtering and amplitude controlled output level
– Optimal sound SNR due to carrier recovery without quadrature distortions
– FM radio capability without external components and with standard TV tuner
– Prepared for digital TV (DVB-C, DVB-T, ATSC)
– I2 C bus interface

NC = not connected, leave vacant LV = if not used, leave vacant
DVSS = if not used, connect to DVSS AHVSS = connect to AHVSS
Pin no Pin name Type Supply Connection Short description

PLCCK 68 pin Voltage (if not used)
1 AVSS_ADC X Analog Ground for ADC
2 AVDD_ADC X Analog Supply for ADC (+5V)
3 ANASTX I/O AVDD_FE8 GND Test pin
4 ANASTY I/O AVDD_FE8 GND Test pin
5 AVDD_FE8 X 2nd analog supply for the front-end
6 AVSS_FE8 X 2nd analog ground for the front-end
7 AVSS_FE40 1st analog ground for the front-end
8 IFINX IN AVDD_FE40 X IF Input
9 AVDD_FE40 X 1st analog supply for the front-end
10 IFINY IN AVDD_FE40 X IF Input
11 AVSS_FE40 X 1st analog ground for the front-end
12 AVDD_SYN X Analog supply for synthesizer (+5V)
13 AVSS_SYN X Analog ground for synthesizer
14 SHIELD IN X Shield GND
15 TEST0 IN AVDD_DAC GND Test pin
22
18 CVBS OUT AVDD_DAC X CVBS Output
19 REF_SW IN AVDD_DAC X Reference frequency switch
20 SIF OUT AVDD_DAC X 2nd SIF output
21 AVDD_DAC X DAC supply (+5V)
22 AVSS_DAC X DAC ground
23 TEST_EN IN DVDD GND Test enable
24 RESETQ IN DVDD X Reset
25 I2C_SDC I/O DVDD X I2C data
26 I2C_SCL I/O DVDD X I2C clock
27 DVDD_CAP X Digital supply capacitor
28 DVDD X Digital supply (+3.3V)
29 DVSS X Digital ground
30 DVSS_CAP X Digital capacitor ground
31 PORT0 OUT DVDD LV Digital output port
33 TUNER_AGC OUT DVDD X Tuner AGC current output
37 ADR_SEL IN DVDD X Address select
39 DVDD_ADC X Digital supply for ADC (+3.3V)
40 DVSS_ADC X Digital ground for ADC
41 XTAL_IN IN AVDD_ADC X Crystal oscillator
42 XTAL_OUT I/O AVDD_ADC X Crystal oscillator/external reference
frequency
43 VREF AVDD_ADC X ADC Reference voltage
44 SGND AVDD_ADC X ADC Reference ground
14.16.LM7808
14.16.1.Description
The L7800 series of three-terminal positive regulators is available in TO -220 TO -220FP TO-3 and D 2
PAK packages and several fixed output voltages, making it useful in a wide range of applications.
These regulators can provide local on-card regulation, eliminating the distribution problems associated
with single point regulation. Each type employs internal current limiting, thermal shutdown and safe
area protection, making it essentially indestructible. If adequate heat sinking is provided, they can
deliver over 1A output current. Although designed primarily as fixed voltage regulators, these devices
can be used with external components to obtain adjustable voltages and currents.
14.16. 2.Features
Output Current Up To 1.5 A
Output Voltages of 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V
Thermal Over load protection
Short Circuit Protection
Output Transition SOA Protection
14.17.BDX53BFI
14.17.1.Description
The BDX53BFI is silicon epitaxial-base NPN power transistor in monolithic Darlington configuration and
are mounted in ISOWATT220 plastic package. It is intended for use in hammer drivers, audio amplifiers
and other medium power linear and switching applications. The complementary PNP type is th e
BDX54BFI.
14.17.2.Applications
General purpose switching and amplifier
Linear and switching industrial equipment
23
14.18.TDA8177F
14.18.1.Description
Designed for monitors and high performance TVs, the TDA8177F vertical deflection booster can handle
flyback voltage up to 70V. More than this it is possible to have a flyback voltage, which is more than the
double of the supply (Pin 2). This allows to decrease the power consumption or to decrease the flyback
time for a given supply voltage. The TDA8177F operates with supplies up to 35V and provides up to
3APP output current to drive the yoke.
14.18.2.Features
Power Amplifier
Thermal Protection
Output Current Up To 3.0APP
Flyback Voltage Up To 70V (on Pin 5)
Suitable For Dc Coupling Application
External Flyback Supply
14.18.4.Block Diagram
14.19.LM1086
14.19.1.Description
The LM1086 is a series of low dropout positive voltage regulators with a maximum dropout of 1.5V at
1.5A of load current. It has the same pin-out as National Semiconductor’s industry standard LM317.
The LM1086 is available in an adjustable version, which can set the output voltage with only two
external resistors. It is also available in five fixed voltages: 2.5V, 2.85V, 3.3V, 3.45V and 5.0V. The fixed
versions integrate the adjust resistors. The LM1086 circuit includes a zener trimmed band-gap
reference, current limiting and thermal shutdown.
14.19.2.Features
Available in 2.5V, 2.85V, 3.3V, 3.45V, 5V and Adjustable Versions
Current Limiting and Thermal Protection
24
Output Current 1.5A
Line Regulation 0.015% (typical)
Load Regulation 0.1% (typical)
SCSI-2 Active Terminator
High Efficiency Linear Regulators
Battery Charger
Post Regulation for Switching Supplies
Constant Current Regulator
Microprocessor Supply
14.19.4.Connection Diagrams
14.20.MC44608
14.20.1.Description
The MC44608 is a high performance voltage mode controller designed for off–line converters. This high
voltage circuit that integrates the start–up current source and the oscillator capacitor, requires few
external components while offering a high flexibility and reliability. The device also features a very high
efficiency stand–by management consisting of an effective Pulsed Mode operation. This technique
enables the reduction of the stand–by power consumption to approximately 1W while delivering 300mW
in a 150W SMPS.
• Integrated Start–Up Current Source
• Lossless Off–Line Start–Up
• Direct Off–Line Operation
• Fast Start–Up
14.20.2.General Features
• Flexibility
• Duty Cycle Control
• Under voltage Lockout with Hysteresis
• On Chip Oscillator Switching Frequency 40, or 75kHz
• Secondary Control with Few External Components
Protections
• Maximum Duty Cycle Limitation
• Cycle by Cycle Current Limitation
• Demagnetization (Zero Current Detection) Protection
• “Over VCC Protection” Against Open Loop
• Programmable Low Inertia Over Voltage Protection Against Open Loop
• Internal Thermal Protection
TM
GreenLine Controller
• Pulsed Mode Techniques for a Very High Efficiency Low Power Mode
• Lossless Startup
• Low dV/dT for Low EMI Radiations
25
14.20.3.Pin Connections
14.20.4.Pin Function description
Pin Name Description

1 Demag The Demag pin offers 3 different functions: Zero voltage crossing detection (50mV),
24mA current detection and 120mA current detection. The 24mA level is used to detect
the secondary reconfiguration status and the 120mA level to detect an Over Voltage
status called Quick OVP.
2 ISENSE The Current Sense pin senses the voltage developed on the series resistor inserted in
the source of the power MOSFET. When I sense reaches 1V, the Driver output (pin 5)
is disabled. This is known as the Over Current Protection function. A 200mA current
source is flowing out of the pin 3 during the start–up phase and during the switching
phase in case of the Pulsed Mode of operation. A resistor can be inserted between the
sense resistor and the pin 3; thus a programmable peak current detection can be
performed during the SMPS stand–by mode.
3 Control Input A feedback current from the secondary side of the SMPS via the opto–coupler is
injected into this pin. A resistor can be connected between this pin and GND to allow
the programming of the Burst duty cycle during the Stand–by mode.
4 Ground This pin is the ground of the primary side of the SMPS.
5 Driver The current and slew rate capability of this pin are suited to drive Power MOSFETs.
6 VCC This pin is the positive supply of the IC. The driver output gets disabled when the
voltage becomes higher than 15V and the operating range is between 6.6V and 13V.
An intermediate voltage level of 10V creates a disabling condition called Latched Off
phase.
7 This pin is to provide isolation between the Vi pin 8 and the VCC pin 6.
8 Vi This pin can be directly connected to a 500V voltage source for start–up function of the
IC. During the Start–up phase a 9 mA current source is internally delivered to the VCC
pin 6 allowing a rapid charge of the VCC capacitor. As soon as the IC starts –up, this
current source is disabled.
14.21.TCET1102G
14.21.1.Description
The TCET110/ TCET2100/ TCET4100 consists of a phototransistor optically coupled to a gallium
arsenide infrared-emitting diode in a 4-lead up to 16-lead plastic dual inline package. The elements are
mounted on one lead frame using a coplanar technique, providing a fixed distance between input and
output for highest safety requirements.
Circuits for safe protective separation against electrical shock according to safety class II (reinforced
isolation):
For appl. class I – IV at mains voltage =300 V
For appl. class I – III at mains voltage =600 V
According to VDE 0884, table 2, suitable for: Switch-mode power supplies, line receiver, computer
peripheral interface, microprocessor system interface.
14.21.3.Features
VDE 0884 related features:
Rated impulse voltage (transient overvoltage) V IOTM = 8 kV peak
Isolation test voltage (partial discharge test voltage) V pd = 1.6 kV
Rated isolation voltage (RMS includes DC) V IOWM = 600 V RMS (848 V peak)
Rated recurring peak voltage (repetitive) V IORM = 600 V RMS
26
General features:
CTR offered in 9 groups
Isolation materials according to UL94-VO
Pollution degree 2 (DIN/VDE 0110 / resp. IEC 664)
Climatic classification 55/100/21 (IEC 68 part 1)
Special construction: Therefore, extra low coupling capacity of typical 0.2pF, high Common Mode
Rejection
Low temperature coefficient of CTR
G = Leadform 10.16 mm; provides creepage distance > 8 mm, for TCET2100/ TCET4100 optional;
suffix letter ‘G’ is not marked on the optocoupler
Coupling System U
14.22.TDA7480L
14.22.1.Description
The TDA7480L is an audio class-D amplifier assembled in Power DIP package specially de-signed for
14.22.2.Features
10W Output Power: RL = 8Ω/4Ω; THD = 10%
High Frequency
No Heatsink
Split Supply
Overvoltage Protection
St-By And Mute Features
Thermal Overload Protection
14.22.3.Pin Functions
Number Name Function

1 -VCC NEGATIVE SUPPLY.
4 OUT PWM OUTPUT
5 BOOTDIODE BOOTSTRAP DIODE ANODE
6 BOOT BOOTSTRAP CAPACITOR
7 NC NOT CONNECTED
8 FEEDCAP FEEDBACK INTEGRATING CAPACITANCE
9 FREQUENCY SETTING FREQUENCY RESISTOR
10 SGN-GND SIGNAL GROUND
11 IN INPUT
12 ST-BY-MUTE ST-BY/ MUTE CONTROL PIN
13 NC NOT CONNECTED
14 +VCC SIGN POSITIVE SIGNAL SUPPLY
15 VREG 10V INTERNAL REGULATOR
16 +VCC POW POSITIVE POWER SUPPLY
17 -VCC NEGATIVE SUPPLY (TO BE CONNECTED TO PIN 16 VIA C5)
18 -VCC NEGATIVE SUPPLY
14.23.SAA3010T
14.23.1.Description
The SAA3010 is intended as a general purpose (RC-5) infrared remote control system for use where a low
voltage supply and a large debounce time are expected. The device can generate 2048 different commands
and utilizes a keyboard with a single pole switch for each key. The commands are arranged so that 32
systems can be addressed, each system containing 64 different commands. The circuit response to legal
(one key pressed at a time) and illegal (more than one key pressed at a time) keyboard operation is specified
in the section “Keyboard operation”.
27
14.23.2.Features
Low voltage requirement
Biphase transmission technique
Single pin oscillator
Test mode facility
14.23.3.Pinning
Pin Mnemonic Function

1 X7 (IPU) sense input from key matrix
2 SSM (I) sense mode selection input
3 Z0-Z3 (IPU) sense inputs from key matrix
7 MDATA (OP3) generated output data modulated with 1/12 the oscillator frequency at a 25% duty factor
8 DATA (OP3) generated output information
9-13 DR7- DR3 (ODN) Scan drivers
14 VSS Ground (0V)
15-17 DR-2- DR0 (ODN) Scan drivers
18 OSC (I) Oscillator input
19 TP2 (I) test point 2
20 TP1 (I) Test point 1
21-27 X0-X6 (IPU) Sense inputs from key matrix
28 VDD(I) Voltage supply
Note:
(I): Input,
(IPU): input with p-channel pull-up transistor,
(ODN): output with open drain n-channel transistor
(OD3): output 3-state
15.AK52 CHASSIS MANUAL ADJUSTMENTS PROCEDURE
15.1.PRELIMINARY
Before starting with the alignment procedure, make sure that all the potentiometers on the chassis and
also screen and focus pots are in the medium position.
15.2.SYSTEM VOLTAGE ADJUSTMENTS

Inputs AC power (220V 50Hz)
PAL B/G test pattern via RF
(PAL I test pattern for PAL I TV’s, SECAM D/K pattern, SECAM L/L’/K’ TVs.)
Outputs Digital voltmeter to anode of D110.
Display System voltage
Action Apply power. Check that the stand-by Led lights.
Select TV mode and tune to the applied test pattern via local test keyboard.
Chassis should start normally.
Adjust all analog controls (volume, bass, treble, brightness, contrast, colour) to minimum
settings.
Adjust VR127 according to the following different type of CRTs.
SYSTEM VOLTAGE TYPE OF CRT

135V±0.5V PHILIPS A66EAK552X54
135V±0.5V VIDEOCOLOR A66ECY13X12
135V±0.5V PHILIPS W66ESF002X44
15.3.AFC ADJUSTMENTS
Inputs AC power
38.9 Mhz test pattern for PAL B/G, PAL-SECAM B/G or 39.5 MHz test pattern for PAL I
model (90dBmV) to Z403 SAW filter input terminals 1 and 2.
Outputs Digital voltmeter to AFC point (pin22 of IC401)
Display AFC Voltage.
Action Adjust VL401 for 2.5±0.1 Volts. TV should automatically tune to a station when search
tuning is activated.
28
15.4.FOCUS ADJUSTMENTS
Inputs AC power
PAL B/G test pattern via RF input.
Outputs Picture tube drive.
Display Picture
Action Select TV mode and tune to the signal.
Adjust focus potantiometer (the upper pot on the rear side of the FBT transformer) for
optimum focusing drive.
15.5.SCREEN ADJUSTMENTS
Inputs AC power
PAL B/G Colour Bar test pattern via RF
Outputs 1/100 Oscilloscope probe to RGB cathodes on CRT baseboard.
st
NOTE: Ground pin of probe will be connected to 1 pin (GND) of the CRT socket.
Display RGB ratio
Action Select PAL B/G Colour bar pattern using the local test keyboard and the user remote
control unit.
Adjust all control functions (brightness, colour and contrast) to minimum settings.
Measure the most sensitive cathode
Adjust the screen potentiometer (lower pot on the rear side of FBT transformer) until
cathode voltage becomes 150V.
15.6.IF ADJUSTMENT FOR L’ MODE

Inputs AC power
38.9 MHz test pattern for PAL B/G, PAL-SECAM B/G or 39.5 MHz test pattern for PAL I
model. (90dBmV) to Z403 SAW filter input terminals 1 and 2.
Outputs Digital Voltmeter to AFC point. (pin22 of IC401)
Digital Voltmeter to AFC_L point. (pin14 of IC401
Display AFC Voltage.
Action Firstly adjust VL401 for 2.5±0.1 Volts. TV should automatically tune to a station when
search tuning is activated.
Adjust VR401 for 2.5±0.1 Volts at the AFC_L point.
29
16.AK52 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS
16.1.PRELIMINARY
All system, geometry and white balance alignments are performed in production service mode. Before
starting the production mode alignments, make sure that all manual adjustments are done correctly. To
start production mode alignments enter the MAIN MENU and then press the digits 1, 6, 7 and 5
respectively. The following first menu appears on the screen. Production mode values will appear on
the screen.
PRODUCTION OK> STORE MENU EXIT PRODUCTION OK> STORE MENU EXIT
H/V VIDEO ADJUSTMENTS OPTIONS

VSHIFT 000 WdR 064 PIP CNTRST 000 0.HPHONE ON
V-SIZE 0068 WdG 064 PIP Ydelay 000 1.CRT 4:3
H-SHIFT 1218 WdB 064 PIP Frame 0 2.SVHS OFF
H-SIZE 012 CuR 064 EHTHP 001 3.f(IF) 38.9
S-COR 027 CuG 064 EHTH TC 000 4.Türk. ON
LINRT -01 CuB 064 EHTH -36 5.VGA OFF
ANGLE 001 YDFP -05 EHTV -14 6.FRONT ON
BOW -03 AGC 009 EHTV TC 005 7.DPL OFF
TRPEZ -07 TLAN W-T SVDEL 008 8.VD ON
PARAB -46 APS ON BCLTHR (mA) 1.1 9.NSL ON
U.COR 001 T_T THO OSD CONT 055 A.PAP OFF
L.COR 008 T_P SAM OSD BRI 040 B.CTI ON
TILT 049 YDFS -07 TEXT BRI 050 C.AVL OFF
TRPZD 020 YDFN -02 PIP YDelSe 000
INIT NVM SYSTEM
NTSCHS 000 EXT3 ON
TXTV 015 DVD OFF 0.PAL B/G ON
Prescaler 1.PAL D/K OFF
C.M ON
AK52 A032 T2 FM 027 2.PAL I OFF
BLUE OFF
08.10.2002 NICAM 061 3.SECAM B/G ON
4:3 000
I2S 016 4.SECAM D/K OFF
OVM ON
AGC READ SCART 025 5.SECAM L/L OFF
-10 SERVICE 6.AUST. OFF
First page Second Page
SERVICE MENU
Production mode groups will be displayed with different colours of headlines, so in order to access a
production alignment group press the colour button of the related group on the remote control
transmitter.
• RED BUTTON is pressed to access H/V menu.
• GREEN BUTTON is pressed to access VIDEO adjust menu.
• BLUE BUTTON is pressed to go to the next page of the service menu.
• YELLOW BUTTON is used to adjust system parameters on the second page of the servi ce menu.
After selecting one of the production service mode groups, you can access its items by pressing ? /?
buttons. Selected parameter will be highlighted. Inorder to change the selected parameter, use ? / ?
buttons. Inorder to switch between other group of items press the colour key of this groups headline.
To store the settings press OK button. To exit the service menu press MENU button.
Entire service menu parameters of AK52 CHASSIS are listed below.
16.2.H/V (HORIZONTAL AND VERTICAL GEOMETRY ALIGNMENTS)

Switch the program to crosshatch test pattern. Press RED button to access this group of item. Select
the parameter by pressing up/down buttons. Adjust the parameter by pressing left/right buttons. Store
the settings by pressing OK button. Switch the another parameter group by pressing the colour button
of the related coloured headline of that group. Exit production mode by pressing the MENU button on
the remote control.
V-SHIFT
Change Vertical Shift by pressing Left/Right buttons till the test pattern is vertically centered. Horizontal
line at the center of the test pattern is in equal distance both to upper and lower side of the picture tube.
30
Check and readjust V-SHIFT item if the adjustment becomes improper after some other geometric
adjustments are done.
Min. Value: -128
Max. Value: 127
Recommended Value: 000
V-SIZE
Change Vertical Size by pressing Left/Right buttons till horizontal black lines on both the upper and
lower part of the test pattern become very close to the upper and lower horizontal sides of picture tube
and nearly about to disappear. Check and readjust V-SIZE item if the adjustment becomes improper
after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
H-SHIFT
Change Horizontal Shift by pressing Left/Right buttons till the the test pattern is horizontally in equal
distance both to right and left sides of the picture tube. Check and readjust H-SHIFT item if the
adjustment becomes improper after some other geometric adjustments are done.
Min. Value: 0000
Max. Value: 1295
H-SIZE
Change Horizontal Size by pressing Left/Right buttons till no under-scan condition will happen, i.e. no
white bars on the left and right side of the test pattern will be visible nor picture will be so wide. Check
and readjust H-SIZE item if the adjustment becomes improper after some other geometric adjustments
are done.
Min. Value: -128
Max. Value: 127
S-COR
Change S-Correction by pressing Left/Right buttons till the size of squares on both the upper and lower
part of test pattern become equal to the squares laying on the vertical center of the test pattern. Check
and readjust S-COR item if the adjustment becomes improper after some other geometric adjustments
are done.
Min. Value: -128
Max. Value: 127
LINRT
Change Linearity by pressing Left/Right buttons till all the size of squares of the test pattern become in
equal size from the top of the screen to its bottom of the whole screen. Check and readjust LINRT item
if the adjustment becomes improper after some other geometric adjustments are done. (especially after
than S-COR adjustment)
Min. Value: -128
Max. Value: 127
Recommended Value: -01
ANGLE
Change Angle by pressing Left/Right buttons till the vertical lines of the crosshatch pattern become
completely perpendicular to horizontal lines without any angle of vertical deviation. Check and readjust
ANGLE item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
31
BOW
Change Bow by pressing Left/Right buttons till the vertical lines especially ones close to the left and
right sides will of equal and symmetrical bending, i.e. they together will neither be towards left side nor
right side. Check and readjust BOW item if the adjustment becomes improper after some other
geometric adjustments are done.
Min. Value: -128
Max. Value: 127
TRPEZ
Change Trapezium by pressing Left/Right buttons till vertical lines, especially lines at the sides of the
picture frame became parallel to the both sides of picture tube as close as possible. Check and readjust
TRPEZ item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
PARAB
Change Parabol by pressing Left/Right buttons till vertical lines close to the both sides of the picture
frame become parallel to vertical sides of picture tube without any bending to left or to right side of the
screen. Check and readjust PARAB item if the adjustment becomes improper after some other
Min. Value: -128
Max. Value: 127
U.COR
Change Upper Correction by pressing Left/Right buttons till vertical lines at the upper corners of the
picture frame become vertical and parallel to vertical corner sides of picture tube. Check and readjust
U.COR item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
L.COR
Change Lower Correction by pressing Left/Right buttons till vertical lines at the lower corners of the
L.COR item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
TILT
This adjustment only works when the TV has rotation option. Change TILT by pressing Left/Right
buttons to rotate the complete raster clock-wise and counter clock-wise depending on the CRT. Check
and readjust TRPEZ item if the adjustment becomes improper after some other geometric adjustments
are done.
Min. Value: 000
Max. Value: 063
TRPZD
Not used for this model.
NTSCHS
Change NTSC horizontal size by pressing Left/Right buttons to adjust till no under-scan condition will
happen, i.e. no white bars on the left and right side of the NTSC test pattern will be visible nor picture
will be so wide. Check and readjust TRPEZ item if the adjustment becomes improper after some other
Min. Value: 000
Max. Value: 010
32
TXTV
Change TXTV by pressing Left/Right buttons to adjust the proper vertical size of Teletext screen. Check
are done.
Min. Value: 000
Max. Value: 040
16.3.VIDEO ALIGNMENTS
Switch the program to colour bar test pattern. Press GREEN button to access this group of item. Select
the settings by pressing OK button.
WdR, WdG, WdB: WHITE BALANCE ADJUSTMENT

Apply WHITE test pattern via RF. Adjust all analog functions to medium level and set WdR to 86, WdG
to 84, WdB to 80, if needed. Use colour analyser and monitor the colour temperature (X,Y) on colour
analyser. Select WdR and WdB by pressing up/down buttons and change the values by Left/Right
buttons till the following values are read:
X=285±10
Y=293±10 on the colour analyser.
CuR, CuG, CuB

Set the values of these items as 64 (constant).
YDFP
Enter a PAL B/G colour and black-white bar test pattern via RF. Adjust Y-Delay for PAL till the colour
transients on the colour bar of the pattern become as sharper and colours between transients do not
mix with each other as possible.
Min. Value: -07
Max. Value: 001
AGC
Apply PAL BG signal, VHF-3 Channel-12 and 60dBmV signal level. Adjust AGC (Automatic Gain
Control) item by pressing Left/Right buttons till the voltage at AGC point (pin1 of the tuner) becomes 3.0
volts.
Min. Value: 000
Max. Value: 015
TLAN
Text language is set. Options are W-T, W-E, W, E. W-T will be selected.
APS
The option of APS (Automatic Program Searching) item are ON and OFF. In order to active APS
installation procedure when TV is turned for the very first time, select ON. Inorder to start TV without
APS installation procedure, select OFF.
T_T
This item is used for the Tuner selection. The options are SAM for SAMSUNG, THO for THOMSON,
SIE for SIEMENS, MK2 and MK3 for PHILIPS MP2/MP3, ALP for ALPS and TEC for Tecnisat. Select
THO.
T_P
This item is also used for the Tuner selection. The options are MK2, SAM, THO, TEM. MK2 for
PHILIPS, SAM for SAMSUNG, THO for THOMSON and TEM for TEMIC. Select SAM.
33
YDFS
Enter a SECAM B/G colour and black-white bar test pattern via RF. Adjust Y-Delay SECAM till the
colour transients on the colour bar of the pattern become as sharper and colours between transients do
not mix with each other as possible.
Min. Value: -07
Max. Value: 001
YDFN
Enter an NTSC colour and black-white bar test pattern via RF. Adjust Y-Delay NTSC till the colour
Min. Value: -07
Max. Value: 001
EXT3
Select ON.
DVD
Select OFF.
C.M
Select ON.
BLUE
Select OFF.
4:3
Set to 0.
OVM
Select ON.
16.4.SERVICE ALIGNMENTS
IMPORTANT: There will no adjustments in this service mode during production mode alignments.
Press BLUE colour button on the remote control when Production mode is active. Press the colour
button of the related item group headline colour. Press up/down buttons to select the item of group.
Press Left/Right button to alter the value of the item. Press OK button to store the selected value and
MENU button to exit the service alignments mode.
ADJUSTMENTS GROUP
Press RED button in order to access this group of items.
PIP CNTRST : Level of the PIP picture
PIP Ydelay : Luma delay of the PIP picture
PIP Frame : Colour selection of the PIP frame (edges of the PIP)
EHTHP : EHT compensation coefficient for horizontal phase
EHTH TC : EHT time constant for horizontal phase compensation
EHTH : EHT compensation coefficient for horizontal amplitude
EHTV : EHT compensation coefficient for vertical amplitude
EHTV TC : EHT time constant for control of vertical and horizontal amplitude EHT
compensation
SVDEL : Delay adjustment for scan velocity modulation
BCLTHR (mA) : Beam current applied to the CRT
OSD CONT : Contrast level of OSD
OSD BRI : Brightness level of OSD
TEXT BRI : Brightness level of text
PIP YDelSe : Y-Delay adjustment for pin-in-picture option
INIT NVM : Press to initiate the NVM
34
PRESCALER GROUP
Press GREEN button in order to access this group of items.
FM : This adjustment is to determine the pre-amplifier gain of MSP for German stereo
Set to 27.
NICAM : This adjustment is to determine the pre-amplifier gain of MSP for Nicam
Set to 61.
I2S : Not used.
SCART : This adjustment is to determine the pre-amplifier gain of MSP for Scart audio inputs
Set to 25.
OPTIONS GROUP
Press BLUE button in order to access this group of items.
0.HPHONE : ON/OFF
1.CRT : 4:3 / 16:9
2.SVHS : ON/OFF
3.f(IF) : always set to 38.9
4.Türk. : Turkish menu ON/OFF
5.VGA : ON/OFF
6.FRONT : Front AV ON/OFF
7.DPL : ON/OFF
8.VD : ON/OFF
9.NSL : ON/OFF
A.PAP : ON/OFF
B.CTI : ON/OFF
C.AVL : ON/OFF
SYSTEM GROUP
Press YELLOW button in order to access this group of items.
0.PAL B/G : ON/OFF
1.PAL D/K : ON/OFF
2.PAL I : ON/OFF
3.SECAM B/G : ON/OFF
4.SECAM D/K : ON/OFF
5.SECAM L/L’ : ON/OFF
6.AUST. : ON/OFF
NOTE: Settings values in Service menu are given for 28” 4:3 THOMSON (A66EHJ13X12) tube in this
manual.
35
17.BLOCK DIAGRAM
MAIN TUNER DRX 3960

(PLL)
GENERAL BLOCK DIAGRAM OF
11 AK 52 150V/160V
+22V
SMPS +14V
PIP TUNER DRX 3960 MC 44608 +14V(audio)
(PLL)
Feature Box Module (MOTOROLA) -14V(audio)
+ +8V
PIP OPTION ACTIVE PFC +5V
MC 33260
(MOTOROLA) +3.3V
+3.3V (ST-BY)
SDA
24W32
+2.5V(ST-BY)
D0-D7 SCL +12
8
(E2PROM)
27W401 SDA5550M
(EPROM) (MicroController)
A0-A18
18
A0-A18
PIP_CVBS 18 SRAM HORIZONTAL
30KV
12V
Horz. FOCUS
Yoke
SCREEN
Lin. +130V
HORZ. Heater
IF_CVBS
TXT_CVBS DRIVE
E/W E/W
U/V DRIVE -Vert.Sup

EW
LUMA LUMA
8 -Vert.Sup
RGB_DVD 8 YUV
30KV
CHROMA CHROMA DDP3315C CRT BOARD
VPC3230D SDA9400 Heater G2 FOCUS
OSD
TDA6109
RGB,FB VERT+
RGB_OUT
VERT-
SWM
3 SENSE COIL
SVM
R
C
G
PIP_CVBS_
B VERTICAL STAGE
Y/CVBS
EXT
C
BSVM
STV9379FA Vert.
Yoke
(VERT. OUT)
SCART2 RGB
TEA6415C
(Video Switching 3
Matrix)
SCART 3/ HEADPHONE
Front_AV SVHS
SCART1 RGB SCART 1 SCART 2 Back_AV L
TDA1308
R
3 AUDIO AMPLIFIER L
SVHS_C
SC1
SC2
SVHS_Y
TDA 7480
SDA
SCL
IF
Back_V Back_A Front_V Front_A C SC2_R(Scart2_C)

Center 8 ohm
12W
S3
R
SCL
SDA
S1 S2 MONO IN QSS Surround
2
8 ohm
C_SW
SDA9488 12W
C
AUDIO AMPLIFIER
8 ohm
MSP 34XX TDA 7480
12W
MAIN_R SR
11AK52 BLOCK SCHEME L R
8 ohm
12W
06.11.2002 MAIN_L
36
18.CIRCUIT DIAGRAMS
11ak52e3-VIDEO
37
11ak52e3-2
38
11ak52e3-3
39
11ak52e3-4
40
11fb2a1—1
41
11fb2a1—2
42
11fb2a1—3
43
11fb2a1—4
44
11uk06-1
45
11txt52-3
46
11rs52
47
11fav19a4
48
11ir2872
11tk109
49
11sb18-3
50
11tk117
11tk118
51
11tp52-1
52
11df41j-2
53
SM52-PHILIPS_IF
TABLE OF CONTENTS
1.INTRODUCTION.......................................................................................................................... 1
2.TUNER........................................................................................................................................ 1
3.IF PART (TDA9885/86) ................................................................................................................ 1
4.VIDEO SWITCH TEA6415............................................................................................................ 2
5.MULTI STANDARD SOUND PROCESSOR .................................................................................. 2
6.SOUND OUTPUT STAGE WITH TDA7480L ................................................................................. 2
7.VERTICAL OUTPUT STAGE WITH TDA8177F............................................................................. 2
8.VIDEO OUTPUT AMPLIFIER TDA6109........................................................................................ 3
9.POWER SUPPLY (SMPS)............................................................................................................ 3
10.MICROCONTROLLER SDA5550................................................................................................ 3
10.1.General Features................................................................................................................ 3
10.2.External Crystal and Programmable Clock Speed.............................................................. 3
10.3.Microcontroller Features.................................................................................................... 3
10.4.Memory .............................................................................................................................. 3
10.5.Display Features................................................................................................................. 3
10.6.ROM Characters................................................................................................................. 4
10.7.Acquisition Features.......................................................................................................... 4
10.8.Ports................................................................................................................................... 4
11.SERIAL ACCESS 32K EEPROM ................................................................................................ 4
12.CLASS AB STEREO HEADPHONE DRIVER TDA1308............................................................... 4
13.SAW FILTERS ........................................................................................................................... 4
14.IC DESCRIPTIONS .................................................................................................................... 5
14.1.TDA6109 ............................................................................................................................. 5
14.1.2.Features....................................................................................................................... 5
14.1.3.Pinning......................................................................................................................... 5
14.2.27W401 ............................................................................................................................... 6
14.2.1.Description................................................................................................................... 6
14.2.2.Features....................................................................................................................... 6
14.2.3.Connections................................................................................................................. 6
14.3.24LC32A............................................................................................................................. 7
14.3.1.Description................................................................................................................... 7
14.3.2.Features....................................................................................................................... 7
14.3.3.Pin Descriptions........................................................................................................... 7
14.4.SDA5275............................................................................................................................. 8
14.4.1.Features....................................................................................................................... 8
14.4.2.Pin Definition and functions......................................................................................... 8
14.5.DRAM 4MX4........................................................................................................................ 9
14.5.2.Features......................................................................................................................10
14.5.3.Pin Assignment...........................................................................................................10
14.6.SDA9400............................................................................................................................10
14.6.1.General Description ....................................................................................................10
14.6.2.Features......................................................................................................................10
14.6.3.Pin Definition ..............................................................................................................11
14.7.LM317T ..............................................................................................................................12
14.7.1.Description..................................................................................................................12
14.7.2.Features......................................................................................................................12
14.8.DDP3310............................................................................................................................12
14.8.1.Description..................................................................................................................12
14.8.2.Features......................................................................................................................12
14.8.3.Pin connection and short descriptions .......................................................................13
14.9.SDA5550............................................................................................................................14
14.9.1.General definition........................................................................................................14
14.9.2.Features......................................................................................................................15
14.10.TEA6415C........................................................................................................................16
14.10.2.Features....................................................................................................................16
14.10.3.Pinning......................................................................................................................16
14.11.VPC3230D........................................................................................................................17
i
14.11.2.Pin Connections and Short Descriptions ..................................................................17
14.12.TDA1308T ........................................................................................................................19
14.12.2.Features....................................................................................................................19
14.12.3.Pinning......................................................................................................................19
14.13.MSP34X1G (MSP3411G) ..................................................................................................19
14.13.1.Description................................................................................................................19
14.13.2.Features....................................................................................................................20
14.13.3.Pin connections ........................................................................................................20
14.14.TL431...............................................................................................................................22
14.14.1.Description................................................................................................................22
14.14.2.Features....................................................................................................................22
14.15.TDA9885/86 .....................................................................................................................22
14.15.1.Introduction...............................................................................................................22
14.15.2.Features....................................................................................................................22
14.16.LM7808 ............................................................................................................................23
14.16.1.Description................................................................................................................23
14.16.2.Features....................................................................................................................23
14.17.TDA8177F ........................................................................................................................24
14.17.1.Description................................................................................................................24
14.17.2.Features....................................................................................................................24
14.17.3.Pin connections ........................................................................................................24
14.17.4.Block Diagram...........................................................................................................24
14.18.LM1086 ............................................................................................................................24
14.18.1.Description................................................................................................................24
14.18.2.Features....................................................................................................................24
14.18.3.Applications..............................................................................................................25
14.18.4.Connection Diagrams................................................................................................25
14.19.MC44608 ..........................................................................................................................25
14.19.1.Description................................................................................................................25
14.19.2.General Features.......................................................................................................25
14.19.3.Pin Connections........................................................................................................26
14.20.TCET1102G......................................................................................................................26
14.20.1.Description................................................................................................................26
14.20.2.Applications..............................................................................................................26
14.20.3.Features....................................................................................................................26
14.21.TDA7480L ........................................................................................................................27
14.21.1.Description................................................................................................................27
14.21.2.Features....................................................................................................................27
14.21.3.Pin Functions............................................................................................................27
14.22.SAA3010T ........................................................................................................................27
14.22.1.Description................................................................................................................27
14.22.2.Features....................................................................................................................28
14.22.3.Pinning......................................................................................................................28
15.AK52 CHASSIS MANUAL ADJUSTMENTS PROCEDURE ........................................................29
15.1.PRELIMINARY ...................................................................................................................29
15.2.SYSTEM VOLTAGE ADJUSTMENTS..................................................................................29
15.3.AFC ADJUSTMENTS .........................................................................................................29
15.4.FOCUS ADJUSTMENTS.....................................................................................................29
15.5.SCREEN ADJUSTMENTS ..................................................................................................29
15.6.IF ADJUSTMENT FOR L’ MODE.........................................................................................29
16.AK52 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS ............................................29
16.1.PRELIMINARY ...................................................................................................................30
16.2.H/V (HORIZONTAL AND VERTICAL GEOMETRY ALIGNMENTS).......................................30
16.3.VIDEO ALIGNMENTS .........................................................................................................33
16.4.SERVICE ALIGNMENTS.....................................................................................................34
17.BLOCK DIAGRAM ....................................................................................................................36
18.CIRCUIT DIAGRAMS................................................................................................................37
ii
1.INTRODUCTION
11AK52 is a 100Hz flicker free colour television capable of driving 28”4:3/16:9, 32” 16:9, 33”4:3 and
29”4:3 real flat picture tubes.
The chassis is capable of operation in PAL, SECAM, NTSC (playback) colour standards and multiple
transmission standards as B/G, D/K, I/I’, and L/L´.
Sound system output is supplying 2x10W (10%THD) for left and right outputs of 8ohm speakers.
TV supports the level 1.5 teletext standard. It is possible to decode transmissions including high
graphical data.
The chassis is equipped with two full EuroScarts, one SCART for AV input/output, one front-AV input,
one back-AV input, one headphone output, one SVHS input (via SCART and SVHS connector), two
external speaker outputs (left and right).
2.TUNER
The hardware and software of the TV is suitable for tuners, supplied by different companies, which are
selected from the Service Menu. These tuners can be combined VHF, UHF tuners suitable for CCIR
2
systems B/G, H, L, L´, I/I´, and D/K. The tuning is available through the digitally controlled I C bus
(PLL). Below you will find info on one of the Tuners in use.
General description of UV1316:

The UV1316 tuner belongs to the UV 1300 family of tuners, which are designed to meet a wide range of
applications. It is a combined VHF, UHF tuner suitable for CCIR systems B/G, H, L, L’, I and I’. The low
IF output impedance has been designed for direct drive of a wide variety of SAW filters with sufficient
suppression of triple transient.
Features of UV1316:
1. Member of the UV1300 family small sized UHF/VHF tuners
2. Systems CCIR: B/G, H, L, L’, I and I’; OIRT: D/K
2
3. Digitally controlled (PLL) tuning via I C-bus
4. Off-air channels, S-cable channels and Hyperband
5. World standardized mechanical dimensions and world standard pinning
6. Compact size
7. Complies to “CENELEC EN55020” and “EN55013”
Pinning:
1. Gain control voltage (AGC) : 4.0V, Max: 4.5V
2. Tuning voltage
3. I²C-bus address select : Max: 5.5V
4. I²C-bus serial clock : Min:-0.3V, Max: 5.5V
5. I²C-bus serial data : Min:-0.3V, Max: 5.5V
6. Not connected
7. PLL supply voltage : 5.0V, Min: 4.75V, Max: 5.5V
8. ADC input
9. Tuner supply voltage : 33V, Min: 30V, Max: 35V
3.IF PART (TDA9885/86)

The TDA9885 is an alignment-free single standard (without positive modulation, only PAL) vision and sound
IF signal PLL.
The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal PLL
Both devices can be used for TV, VTR, PC and set -top box applications.
The following figure shows the simplified block diagram of the integrated circuit.
The integrated circuit comprises the following functional blocks:
VIF amplifier, Tuner and VIF-AGC, VIF-AGC detector, Frequency Phase-Locked Loop (FPLL) detector, VCO
and divider, Digital acquisition help and AFC, Video demodulator and amplifier, Sound carrier trap, SIF
amplifier, SIF-AGC detector, Single reference QSS mixer, AM demodulator, FM demodulator and acquisition
help, Audio amplifier and mute time constant, I2C-bus transceivers and MAD (module address), Internal
voltage stabilizer.
1
4.VIDEO SWITCH TEA6415
In case of three or more external sources are used, the video switch IC TEA6415 is used. The main
function of this device is to switch 8 video-input sources on the 6 outputs.
Each output can be switched on only one of each input. On each input an alignment of the lowest level
of the signal is made (bottom of sync. top for CVBS or black level for RGB signals).
Each nominal gain between any input and output is 6.5dB.For D2MAC or Chroma signal the alignment
is switched off by forcing, with an external resistor bridge, 5VDC on the input. Each input can be used
as a normal input or as a MAC or Chroma input (with external Resistor Bridge). All the switching
possibilities are changed through the BUS. Driving 75ohm load needs an external resistor. It is possible
to have the same input connected to several outputs.
5.MULTI STANDARD SOUND PROCESSOR

The MSP34x1G family of single-chip Multi-standard Sound Processors covers the sound processing of
all analog TV -Standards worldwide, as well as the NICAM digital sound standards. The full TV sound
a single chip. Signal conforming to the standard by the Broadcast Television Systems Committee
(BTSC).
The DBX noise reduction, or alternatively, MICRONAS Noise Reduction (MNR) is performed alignment
free. Other processed standards are the Japanese FM-FM multiplex standard (EIA -J) and the FM
Stereo Radio standard.
6.SOUND OUTPUT STAGE WITH TDA7480L

The TDA7480L is an audio class-D amplifier assembled in Power DIP package specially designed for
Mute stand-by function of the audio amplifier can be described as the following; the pin 12
(MUTE/STAND-BY) controls the amplifier status by two different thresholds, referred to ground. When
Vpin 12 voltage is lower than 0.7V the amplifier is in Stand-by mode and the final stage generators are
off. When Vpin 12 is higher than 4V, the amplifier is in play mode.
The TDA7480L is a 10W+10W stereo sound amplifier with mute/stand-by facility. MUTE control signal
coming from microcontroller (when it is at high level) activates the mute function. IC is muted when
mute pin is at low level (pin12). MUTE pin can also be activated via an external pop-noise circuitry in
order to eliminate pop noise when TV is turned off. Just after the TV is turned off, this circuit switches
the IC to stand-by mode by pulling the mute pin voltage to ground.
7.VERTICAL OUTPUT STAGE WITH TDA8177F

The IC TDA8177F is the vertical deflection booster circuit. Two supply voltages, +12V and -12V are
needed to scan the inputs VERT+ and VERT-, respectively. And a third supply voltage, +60V for the
flyback limiting are needed. The vertical deflection coil is connected in series between the output and
feedback to the input.
2
8.VIDEO OUTPUT AMPLIFIER TDA6109
The TDA6109 includes three video output amplifiers in order to drive the three cathodes of a colour
picture tube directly. To obtain maximum performance, the amplifier is used with black-current control.
9.POWER SUPPLY (SMPS)

The DC voltages required at various parts of the chassis are provided by an SMPS transformer
controlled by the IC MC44608, which is designed for driving, controlling and protecting switching
transistor of SMPS. The transformer generates 135V for FBT input, +/-14V for audio amplifier, 8V stand
by voltage and 8V, 12V and 5V supplies for other different parts of the chassis.
An optocoupler is used to control the regulation of line voltage and stand-by power consumption. There
is a regulation circuit in secondary side. This circuit produces a control voltage according to the
changes in 135V DC voltage, via an optocoupler (TCET 1102G) to pin3 of the IC.
During the switch on period of the transistor, energy is stored in the transformer. During the switch off
period energy is fed to the load via secondary winding. By varying switch-on time of the power
transistor, it controls each portion of energy transferred to the second side such that the output voltage
remains nearly independent of load variations.
10.MICROCONTROLLER SDA5550
10.1.General Features
• ROM version is used.
10.2.External Crystal and Programmable Clock Speed
• Single external 6MHz crystal, all necessary clocks are generated internally
• CPU clock speed selectable via special function registers.
• Normal Mode 33.33 MHz CPU clock, Power Save mode 8.33 MHz
10.3.Microcontroller Features
• 0.360 ms (min.) instruction cycle
• Watchdog timer
• UART (rxd, txd)
10.4.Memory
10.5.Display Features
• ROM Character set supports all East and West European Languages in single device
• CLUT with up to 4096 colour combinations
• Up to 16 Colours per DRCS Character
• One out of 8 Colours for Foreground and Background Colours for 1-bit DRCS and ROM Characters
3
10.6.ROM Characters
• Shadowing
• Pixel by Pixel Shiftable Cursor With up to 4 Different Colours
10.7.Acquisition Features
• Multi-standard Digital Data Slicer
• Data Caption only limited by available Memory
10.8.Ports
2
• One 8-bit I/O-port with open drain output and optional I C Bus emulation support (Port0)
• Two 8-bit multifunction I/O-ports (Port1, Port3)
• One 4-bit port working as digital or analogue inputs for the ADC (Port2)
• One 2-bit I/O port with secondary function (P4.2, 4.3, 4.7)
11.SERIAL ACCESS 32K EEPROM

24LC32 is the 32Kbit electrically erasable programmable memory. The memory is compatible with the
2
I C standard, two wire serial interface, which uses a bi-directional data bus and serial clock.
12.CLASS AB STEREO HEADPHONE DRIVER TDA1308

The TDA1308 is an integrated class AB stereo headphone driver contained in a DIP8 plastic package.
The device is fabricated in a 1 mm CMOS process and has been primarily developed for portable digital
audio applications.
13.SAW FILTERS
K3953M:
Standard
B/G, D/K, I, L/L’
Features
TV IF video filter with Nyquist slopes at 33,90 MHz and 38,90 MHz
Constant group delay
Suitable for CENELEC EN 55020
Terminals
Tinned CuFe alloy
Pin configuration
1 Input
2 Input - ground
3 Chip carrier - ground
4 Output
5 Output
K3958M:
Standard
B/G, D/K, I, L/L’
Features
TV IF video filter with Nyquist slopes at 33.90 MHz and 38.90 MHz
Constant group delay
Terminal and Pin configuration are the same with K3953M
4
K9356M:
Standard
B/G, D/K, I, L
Features
TV IF audio filter with pass band for sound carriers at 32,40 MHz (D/K, L), 32,90 MHz (I) and 33,40 MHz
(B/G)
K9656M:
Standard
B/G, D/K, I, L/L’
Features
TV IF audio filter with two channels
Channel 1 (L’) with one pass band for sound carriers at 40,40 MHz (L’) and 39,75 MHz (L’- NICAM)
Channel 2 (B/G, D/K, L, I) with one pass band for sound carriers between 32,35 MHz and 33,40 MHz
14.IC DESCRIPTIONS
TDA6109 27W401
24LC32 SDA5275
DRAM 4MX4 SDA9400
LM317T DDP3310
SDA5550 TEA6415
VPC3230D TDA1308T
MSP3411G TL431
TDA9885/86 LM7808
TDA8177F LM1086
MC44608 TCET1102G
TDA7480L SAA3010T
14.1.TDA6109
The TDA6109JF includes three video output amplifiers in one plastic DIL-bent-SIL 9-pin medium power
(DBS9MPF) package (SOT111-1), using high-voltage DMOS technology, and is intended to drive the three
cathodes of a colour CRT directly. To obtain maximum performance, the amplifier should be used with black-
current control.
14.1.2.Features
· Typical bandwidth of 9.0 MHz for an output signal of 60 V (p-p)
· High slew rate of 1850 V/ms
· No external components required
· Very simple application
· Single supply voltage of 200 V
· Internal reference voltage of 2.5 V
· Fixed gain of 51
· Black-Current Stabilization (BCS) circuit
· Thermal protection
14.1.3.Pinning

GND 4 ground (fin)
Iom 5 black current measurement output
VDD 6 supply voltage
5
14.2.27W401
14.2.1.Description
The M27W401 is a low voltage 4 Mbit EPROM offered in the two ranges UV (ultra violet erase) and
OTP (one time programmable). It is ideally suited for microprocessor systems requiring large data or
program storage and is organized as 524,288 by 8 bits. The M27W401 operates in the read mode with
a supply voltage as low as 2.7V at –40 to 8??C temperature range. The decrease in operating power
allows either a reduction of the size of the battery or an increase in the time between battery re-
charges.
The FDIP32W (window ceramic frit-seal package) has a transparent lid, which allows the user to ex-
pose the chip to ultraviolet light to erase the bit pat -tern. A new pattern can then be written to the device
by following the programming procedure. For application where the content is programmed only one
time and erasure is not required, the M27W401 is offered in PDIP32, PLCC32 and TSOP32 (8x20 mm)
packages.
14.2.2.Features
2.7V to 3.6v Low voltage in Read Operation
Access time:
Pin Compatible with M27C4001
Low Power Consumption:
–1?mA max Standby Current
– 15mA max Active Current at 5MHz
Programming Time 10? ms/byte
High Reliability CMOS Technology
– 2,000V ESD Protection
– 200mA Latchup Protection Immunity
Electronic Signature
– Manufacturer Code: 20h
– Device Code: 41h
14.2.3.Connections
DIP connections LCC Connections TSOP Connections
6
Signal Names
A0-A18 Address Inputs
Q0-Q7 Data Outputs
E Chip Enable
G Output Enable
Vpp Program Supply
Vcc Supply Voltage
Vss Ground
14.3.24LC32A
14.3.1.Description
The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM
capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced,
low power applications such as personal communications or data acquisition. The 24LC32A also has a
page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential
reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the
same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range
make this device ideal for low-power/ low-voltage, nonvolatile code and data applications. The
24LC32A is available in the standard 8-pin plastic DIP and both 150 mil and 200 mil SOIC packaging.
14.3.2.Features
• Single supply with operation down to 2.5V
• Maximum write current 3 mA at 6.0V
• Standby current 1 mA max at 2.5V
• 2-wire serial interface bus, I 2 CÔ compatible
• 100 kHz (2.5V) and 400 kHz (5V) compatibility
• Self-timed ERASE and WRITE cycles
• Power on/off data protection circuitry
• Hardware write protect
• 1,000,000 Erase/Write cycles guaranteed
• 32 byte page or byte write modes available
• Schmitt trigger filtered inputs for noise suppression
• Output slope control to eliminate ground bounce
• 2 ms typical write cycle time, byte or page
• Up to eight devices may be connected to the same bus for up to 256K bits total memory
• Electrostatic discharge protection > 4000V
• Data retention > 200 years
• 8-pin PDIP and SOIC packages
• Temperature ranges
• Commercial (C): 0°C to +75°C
• Industrial (I): -40°C to +85°C
14.3.3.Pin Descriptions
A0, A1, A2 Chip Address Inputs
The A0..A2 inputs are used by the 24LC32A for multiple device operation and conform to the 2-wire bus
standard. The levels applied to these pins define the address block occupied by the device in the
address map. A particular device is selected by transmitting the corresponding bits (A2, A1, A0) in the
control byte.
SDA Serial Address/Data Input/Output

This is a Bi-directional pin used to transfer addresses and data into and data out of the device. It is an
open drain terminal, therefore the SDA bus requires a pull up resistor to VCC (typical 10 kO for 100 kHz,
2 kO for 400 kHz) For normal data transfer SDA is allowed to change only during SCL low. Changes
during SCL HIGH are reserved for indicating the START and STOP conditions.
SCL Serial Clock

This input is used to synchronize the data transfer from and to the device.
7
WP
This pin must be connected to either VSS or VCC. If tied to VSS, normal memory operation is enabled
(read/write the entire memory 000-FFF). If tied to VCC, WRITE operations are inhibited. The entire
memory will be write-protected. Read operations are not affected.
W CC
+2.5V to 6V Power Supply
W SS
Ground
14.4.SDA5275
14.4.1.Features
• Single chip teletext IC
• Analog CVBS-input with onchip clamping circuitry
• Slicer
• Supports level 1, 2.5 and 3.5 ETSI teletext standard
• Stores up to 14 teletext pages on chip
• Stores up to 2048 teletext pages with external 16 M memory
• SDA 5275: full level 2.5 processing
• Analog RGB-output
• 41 Latin script languages
• 12 ´ 10 character size
• Parallel display attributes
• 64 from 4096 colors selectable
• Enhanced flash modes
• Dynamically redefinable character set (DRCS, PCS)
• Pixel graphics
• Full screen display (64 ´ 32 or 80 ´ 24 character positions)
• Horizontal and vertical scrolling
• Graphic cursors
• 4:3 and 16:9 display
• Multinorm display (50/60/100/120 Hz)
• RISC-processor
• Firmware downloadable
2
• I C / 3 wire UART-interface (1 Mbit/s)
• Independent clocks for acquisition and display
• Tools for greatly simplified software development
• 24-Kbyte on-chip reconfigurable DRAM
• 44160-bit character ROM
• One external crystal for all standards
14.4.2.Pin Definition and functions
Pin No. P-LCC-68-1 Symbol Function

1 INTQ Interrupt request output to ext. controller
2 CLK-IO System clock input/output
3 TCSQ/FLD Composite sync output/ field output
4 VS/VCS Vertical sync input/output
5 HS Horizontal sync input/output
6 XOUT 20.5-MHz crystal oscillator output
7 XIN 20.5-MHz crystal oscillator input
8 GPO General purpose output
9 TM Test pin, leave open or connect VSS
10 CVBS CVBS-video signal input
12 VDDA + 5 V analog supply
17 RES Chip reset
8
23 VREF + 3 V reference voltage input
38 RASQ Row address strobe (DRAM)
39 WEQ Write enable (DRAM)
45 CASQ Column address strobe
56 VBB Substrate bias voltage N.C.* (depends on version)
59 RGB-GND RGB-ground
61 R Analog red display output
62 G Analog green display output
63 B Analog blue display output
64 BLAN Blanking signal open drain output
65 CORQ Contrast reduction open drain output
66 SCL Bi-directional I2C Bus clock port
67 SDA Bi-directional I2C Bus data port
68 I2CEN I2C Bus enable
14.5.DRAM 4MX4
The 4 Meg x 4 DRAM is a randomly accessed, solid-state memory containing 16,777,216 bits
organized in a x4 con-figuration. RAS# is used to latch the row address (first 11 bits for 2K and first 12
bits for 4K). Once the page has been opened by RAS#, CAS# is used to latch the column address (the
latter 11 bits for 2K and the latter 10 bits for 4K, address pins A10 and A11 are “don’t care”). READ and
WRITE cycles are selected with the WE# input. A logic HIGH on WE# dictates READ mode, while a
logic LOW on WE# dictates WRITE mode. During a WRITE cycle, data-in (D) is latched by the falling
edge of WE# or CAS#, whichever occurs last. An EARLY WRITE occurs when WE# is taken LOW prior
to CAS# falling. A LATE WRITE or READ-MODIFY-WRITE occurs when WE# falls after CAS# is taken
LOW. During EARLY WRITE cycles, the data outputs (Q) will remain High-Z regardless of the state of
OE#. During LATE WRITE or READ-MODIFY-WRITE cycles, OE# must be taken HIGH to disable the
9
data outputs prior to applying input data. If a LATE WRITE or READ-MODIFY-WRITE is attempted
while keeping OE# LOW, no write will occur, and the data outputs will drive read data from the
accessed location. The four data inputs and the four data outputs are routed through four pins using
common I/O, and pin direction is controlled by WE# and OE#.
14.5.2.Features
• Industry-standard x4 pin out, timing, functions and packages
• State-of-the-art, high-performance, low-power CMOS silicon-gate process
• Single power supply (+3.3V ±0.3V or +5V ±10%)
• All inputs, outputs and clocks are TTL-compatible
• Refresh modes: RAS#-ONLY, HIDDEN and CAS#-BEFORE - RAS# (CBR)
• Optional Self Refresh (S) for low-power data retention
• 11 row, 11 column addresses (2K refresh) or 12 row, 10 column addresses (4K refresh)
• Extended Data-Out (EDO) PAGE MODE access cycle
• 5V-tolerant inputs and I/Os on 3.3V devices
14.5.3.Pin Assignment
Top View
*NC on 2K refresh and A11 on 4K refresh options. Note: The “#” symbol indicates signal is active LOW.
14.6.SDA9400
The SDA9400 is a new component of the Micronas MEGAVISION ® IC set in a 0.35µm embedded
DRAM technology (frame memory embedded). The SDA9400 is pin compatible to the SDA9401 (field
memory embedded). The SDA9400 comprises all main functionalities of a digital feature box in one
monolithic IC. The scan rate conversion to 100/120 Hz interlaced (50/60 Hz progressive) is based on a
motion adaptive algorithm. The scan rate converted picture can be vertically expanded. The SDA9400
has a free running mode, therefore features like scan rate conversion to e.g. 70, 75 Hz with joint lines or
multiple picture display (e.g. tuner scan) are possible. Due to the frame based signal processing, the
noise reduction has been greatly improved. Furthermore separate motion detectors for luminance and
chrominance have been implemented. For automatic controlling of the noise reduction parameters a
noise measurement algorithm is included, which measures the noise level in the picture or in the
blanking period. In addition a spatial noise reduction is implemented, which reduces the noise even in
the case of motion. The input signal can be compressed horizontally and vertically with a certain
number of factors. Therefore split screen is supported. Beside these additional functions like coloured
background, windowing and flashing are implemented.
14.6.2.Features
• Two input data formats
- 4:2:2 luminance and chrominance parallel (2 x 8 wires)
- ITU-R 656 data format (8 wires)
10
• Two different representations of input chrominance data
- 2‘s complement code
- Positive dual code
• Flexible input sync controller
• Flexible compression of the input signal
- Digital vertical compression of the input signal (1.0, 1.25, 1.5, 1.75, 2.0, 3.0, 4.0)
- Digital horizontal compression of the input signal (1.0, 2.0, 4.0)
• Noise reduction
- Motion adaptive spatial and temporal noise reduction (3D-NR)
- Temporal noise reduction for luminance frame based or field based
- Temporal noise reduction for chrominance field based
- Separate motion detectors for luminance and chrominance
- Flexible programming of the temporal noise reduction parameters
- Automatic measurement of the noise level (5-bit value, readable by I²C bus)
• 3-D motion detection
- High performance motion detector for scan rate conversion
- Global motion detection flag (readable by I²C bus)
- Movie mode and phase detector (readable by I²C bus)
• TV mode detection by counting line numbers (PAL, NTSC, readable by I²C bus)
• Embedded memory
- 5 Mbit embedded DRAM core for field memories
- 192 kbit embedded DRAM core for line memories
• Flexible clock and synchronization concept
- Decoupling of the input and output clock system possible
• Scan rate conversion
- Motion adaptive 100/120 Hz interlaced scan conversion
- Motion adaptive 50/60 Hz progressive scan conversion
- Simple static interlaced and progressive conversion modes for 100/120 Hz interlaced or 50/60 Hz
progressive scan conversion: e.g. ABAB, AABB, AA*B*B, AAAA, BBBB, AB, AA*
- Simple progressive scan conversion with joint lines:
50 Hz -> 60, 70, 75 Hz progressive
60 Hz -> 70, 75 Hz progressive
- Large area and line flicker reduction
• Flexible digital vertical expansion of the output signal (1.0, ... [1/32] ..., 2.0)
• Flexible output sync controller
- Flexible positioning of the output signal
- Flexible programming of the output sync raster
- External synchronization by backend IC possible
(e.g. split screen for one TV channel with joint lines and one PC VGA channel)
• Signal manipulations
- Insertion of coloured background
- Vertical and/or horizontal windowing with four different speed factors
- Flash generation (for supervising applications, motion flag readable by I²C bus)
- Still frame or field
- Support of split screen applications
- Multiple picture display - Tuner scan (4 and 16 times for 4:3, 12 times for 16:9 tubes)
- Support of multi picture display with PIP or front -end processor with integrated scaler
(e.g. 9 times display of PIP pictures, picture tracking, random pictures, still-in-moving picture, moving-
in-still picture)
• I²C-bus control (400 kHz)
• P-MQFP-64 package
• 3.3 V ± 5% supply voltage
14.6.3.Pin Definition
Pin No. Name Type Description

2,8,24,42,55 VSS1 S Supply voltage ( V SS = 0 V )
9,25,41,56 VDD1 S Supply voltage ( V DD = 3.3 V )
36,52,58 VSS2 S Supply voltage ( V SS = 0 V )
35,51,53,57,59 VDD2 S Supply voltage ( V DD = 3.3 V )
43,..,50 YIN0...7 I/TTL Data input Y (see input data format)
31,..,34;37,...,40 UVIN0...7 I/TTL Data input UV (for 4:2:2 parallel, see input data format)
11
PD (for CCIR 656, see input data format)
30 RESET I/TTL System reset. The RESET input is low active. In order to ensure
correct operation a "Power On Reset" must be performed. The
RESET pulse must have a minimum duration of two clock periods
of the system clock CLK1.
23 HIN I/TTL H-Sync input
22 VIN I/TTL V-Sync input
29 SYNCEN I/TTL Synchronization enable input
21 SDA I/O I2C-Bus data line (5V ability)
20 SCL I I I2C-Bus clock line (5V ability)
54 CLK1 I/TTL System clock 1
17,..,10 UVOUT0...7 O/TTL Data output UV (see output data format)
7,..,3;1;64;63 YOUT0...7 O/TTL Data output Y (see output data format)
62 HREF O/TTL Horizontal active video output
61 VOUT/ I/O/ EXSYN=0 (I²C-bus parameter): V-Sync output
VEXT TTL EXSYN=1: External V-Sync input for output part
60 HOUT/ I/O/ EXSYN=0 (I²C-bus parameter): H-Sync output
HEXT TTL EXSYN=1: External H-Sync input for output part
18 INTERLACED O/TTL Interlace signal for AC coupled vertical deflection
28 X1 / CLK2 I/TTL Crystal connection / System clock 2
27 X2 O/AN Crystal connection
26 CLKOUT O/TTL Clock output (depends on I²C parameters CLK11EN, CLK21EN,
FREQR)
19 TEST I/TTL Test input, connect to V SS for normal operation
14.7.LM317T
14.7.1.Description
The LM317T is an adjustable 3 terminal positive voltage regulator capable of supplying in excess of 1.5
amps over an output range of 1.25 to 37 volts. This voltage regulator is exceptionally easy to use and
requires only two external resistors to set the output voltage. Further, it employs internal current limiting,
thermal shutdown and safe area compensation, making it essentially blow–out proof. The LM317
serves a wide variety of applications including local, on card regulation. This device can also be used to
make a programmable output regulator, or by connecting a fixed resistor between the adjustment and
output, the LM317 can be used as a precision current regulator.
14.7.2.Features
• Output Current in Excess of 1.5 A
• Output Adjustable between 1.2 V and 37 V
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting Constant with Temperature
• Output Transistor Safe–Area Compensation
• Floating Operation for High Voltage Applications
2
• Available in Surface Mount D PAK, and Standard 3–Lead Transistor Package
• Eliminates Stocking many Fixed Voltages
14.8.DDP3310
14.8.1.Description
The DDP 3310B is a single-chip digital Display and Deflection Processor designed for high-quality
back-end applications in 100/120-Hz TV sets with 4:3 or 16:9 picture tubes. The IC can be combined
with members of the DIGIT 3000 IC family (VPC 32xx, TPU 3040), or it can be used with third-party
products. The IC contains the entire digital video component and deflection processing and all analog
interface components.
14.8.2.Features
Video processing
– linear horizontal scaling (0.25 … 4)
– non-linear horizontal scaling “panorama-vision”
– dynamic peaking
12
– soft limiter (gamma correction)
– color transient improvement
– programmable RGB matrix
– picture frame generator
– two analog RGB/Fast-Blank inputs. The DDP 3310B is a single-chip digital Display and Deflection
Processor designed for high-quality back-
Deflection processing
– scan velocity modulation output
– high-performance H/V deflection
– EHT compensation for vertical / East/West
– soft start/stop of H-Drive
– vertical angle and bow
– differential vertical output
– vertical zoom via deflection
– horizontal and vertical protection circuit
– adjustable horizontal frequency for VGA/SVGA display
Miscellaneous
– selectable 4:1:1/ 4:2:2 YC r C b input
– selectable 27/ 32-MHz line-locked clock input
– crystal oscillator for horizontal protection
– automatic picture tube adjustment (cutoff, white-drive)
– single 5-V power supply
– hardware for simple 50/60-Hz to 100/ 120-Hz conversion (display frequency doubling)
– two I2 C-controlled PWM outputs
– beam current limiter

NC = not connected LV = if not used, leave vacant
X = obligatory; connect as described in circuit diagram IN = Input
OUT = Output SUPPLY = Supply Pin
Pin no Pin name Type Connection Short description
PLCCK 68 pin (if not used)
1 VSUPP SUPPLY X Supply voltage, Output pin driver
2 GNDP SUPPLY X Ground, Output pin driver
3 VS2 IN GNDD Additional VSYNC input
4 FIFORRD OUT LV FIFO Read counter reset
5 FIFORD OUT LV FIFO Read Enable
6 FIFOWR OUT LV FIFO Write Enable
7 FIFORWR OUT LV FIFO Write counter reset
8 HOUT OUT X Horizontal Drive Output
9 HFLB IN Hout Horizontal Flyback Input
10 SAFETY IN GNDO Safety Input
11 VPROT IN GNDO Vertical protection Input
12 FREQSEL IN X Selection of H-Drive Frequency Range
13 CM1 IN X Clock select 40.5 or 27/32 MHz
14 CMO IN X Clock select 27/32 MHz
15 RSW2 OUT LV Range Switch2, Measurement ADC
16 RSW1 IN/OUT LV Range Switch1, Measurement ADC
17 SENSE IN GNDO Sense ADC Input
18 GNDM SUPPLY X Ground, MADC Input
19 VERT+ OUT GNDO Differantial Vertical Sawtooth Output
20 VERT- OUT GNDO Differantial Vertical Sawtooth Output
21 EW OUT GNDO Vertical Parabola Output
22 XREF IN X Reference Input for RGB DACs
23 SVM OUT VSUPO Scan Velocity Modulation
24 ROUT OUT VSUPO Analog Output Red
25 GOUT OUT VSUPO Analog Output Green
26 BOUT OUT VSUPO Analog Output Blue
27 GNDO SUPPLY X Ground, Analog Back-end
28 VSUPO SUPPLY X Supply Voltage, Analog Back-end
13
29 VRD/BCS IN X DAC Reference, Beam Current Safety
38 TEST IN GNDD Test Pin
39 RESQ IN X Reset Input, active low
42 HCS IN GNDD Half-contrast
43 C0 IN GNDD Picture Bas Chroma (LSB)
50 C7 IN GNDD Picture Bas Chroma (MSB)
51 VSUPD SUPPLY X Supply Voltage, Digital Circuitry
52 GNDD SUPPLY X Ground, Digital Circuitry
53 LLC2 IN X System Clock Input (27/32/40.5 MHz)
54 Y0 IN GNDD Picture Bas Luma (LSB)
61 Y7 IN GNDD Picture Bas Luma (MSB)
62 LLC1 IN VSUPD Single Line-Locked Clock Input (13.5/16 MHz)
63 HS IN X Horizontal Sync Input
64 VS IN GNDD Vertical Sync Input
65 XTALK2 OUT X Analog Crystal Output (5-MHz Security Clock)
66 XTALK1 IN X Analog Crystal Input (5-MHz Security Clock)
67 SDA IN/OUT X I2C-Bus Data
68 SCL IN/OUT X I2C-Bus Clock
14.9.SDA5550
14.9.1.General definition
The SDA5550M is a single chip teletext decoder for decoding World System Teletext data as well as
Video Programming System (VPS), Program Delivery Control (PDC), and Wide Screen Signalling
(WSS) data used for PAL plus transmissions (Line 23). The device provides an integrated general-
purpose, fully 8051-compatible Microcontroller with television specific hardware features.
Microcontroller has been enhanced to provide powerful features such as memory banking, data
pointers, and additional interrupts etc. The on-chip display unit for displaying Level 1.5 teletext data can
also be used for customer defined on screen displays. Internal XRAM consists of up to 17 Kbytes. This
device can support external memory up to 1Mbyte ROM and RAM.TVTEXT Controller contains a data
slicer for VPS, WSS, PDC and TXT, an acceleration acquisition hardware module, a display generator
for Level 1.5 TXT and powerful On screen Display capabilities based on parallel attributes, and pixel
oriented characters (DRCS). The 8 bit Microcontroller operates at 360nsec cycle time (min). Controller
with dedicated hardware does most of the internal TXT acquisition processing, transfer data to/from
2
external memory interface and receives/transmits data via I C-firmware user interface. SDA5550M is
realized in 0.25 micron technology with 2.5V supply voltage and 3.3V I/O compatible. The IC produces
the following input or output control signals; AGC_CON, MODE_SW, L / L’, PIP_MODS, PIP_SEL,
ON/OFF (stand-by), SC1..3_IN_AV (pin 8 information from 3 SCARTs), AFC, MUTE (to mute audio
2
output IC), I CEN.
14
14.9.2.Features
General
External Crystal and Programmable clock speed

Single external 6MHz crystal, all necessary clocks are generated internally
CPU clock speed selectable via special function registers.
Normal Mode 33.33 MHz CPU clock, Power Save mode 8.33 MHz
Microcontroller Features
• 0.360ms (min.) instruction cycle
• Watchdog timer
• UART
Memory
• Non-multiplexed 8-bit data and 16 … 20-bit address bus (ROMless Version)
• Memory banking up to 1Mbyte (Romless version)
Display Features
• ROM Character Set Supports all East and West European Languages in single device
• CLUT with up to 4096 color combinations
• Up to 16 Colors per DRCS Character
• One out of Eight Colors for Foreground and Background Colors for 1-bit DRCS and ROM Characters
• Shadowing
• Pixel by Pixel Shiftable Cursor With up to 4 Different Colors
15
Acquisition Features
• Multistandard Digital Data Slicer
• Data Caption only Limited by available Memory
Ports
2
• One 8-bit I/O-port with open drain output and optional I C Bus emulation support (Port 0)
• Two 8-bit multifunction I/O-ports (Port 1, Port 3)
• One 4-bit port working as digital or analog inputs for the ADC (Port 2)
• One 2-bit I/O port with secondary functions (P4.2, 4.3, 4.7)
14.10.TEA6415C
The main function of the IC is to switch 8 video input sources on 6 outputs. Each output can be
switched on only one of each input. On each input an alignment of the lowest level of the signal is made
(bottom of synch. top for CVBS or black level for RGB signals). Each nominal gain between any input
and output is 6.5dB. For D2MAC or Chroma signal the alignment is switched off by forcing, with an
external resistor bridge, 5 VDC on the input. Each input can be used as a normal input or as a MAC or
Chroma input (with external resistor bridge). All the switching possibilities are changed through the
BUS. Driving 75? load needs an external transistor. It is possible to have the same input connected to
several outputs. The starting configuration upon power on (power supply: 0 to 10V) is undetermined. In
this case, 6 words of 16 bits are necessary to determine one configuration. In other case, 1 word of 16
bits is necessary to determine one configuration.
14.10.2.Features
• 20MHz Bandwidth
• Cascadable with another TEA6415C (Internal address can be changed by pin 7 voltage)
• 8 Inputs (CVBS, RGB, MAC, CHROMA,...)
• 6 Outputs
• Possibility of MAC or chroma signal for each input by switching-off the clamp with an external resistor
bridge
• Bus controlled
• 6.5dB gain between any input and output
• 55dB crosstalk at 5mHz
• Fully ESD protected
14.10.3.Pinning
2. Data : Low level : -0.3V Max: 1.5V,
4. Clock : Low level : -0.3V Max: 1.5V,
7. Prog
8. Input : Max : 2Vpp, Input Current: 1mA, Max: 3mA
9. Vcc : 12V
16
12. Ground
19. Ground
20. Input : Max : 2Vpp, Input Current : 1mA, Max : 3mA
14.11.VPC3230D
The VPC 323xD is a high-quality, single-chip video front-end, which is targeted for 4:3 and 16:9, 50/60-
Hz and 100/120 Hz TV sets. It can be combined with other members of the DIGIT3000 IC family (such
as DDP 331x) and/or it can be used with 3rd-party products. The main features of the VPC 323xD are;
– high-performance adaptive 4H comb filter Y/C separator with adjustable vertical peaking
– multi-standard color decoder PAL/NTSC/SECAM including all substandards
– four CVBS, one S-VHS input, one CVBS output
– two RGB/YC r C b component inputs, one Fast Blank (FB) input
– integrated high-quality A/D converters and associated clamp and AGC circuits
– multi-standard sync processing
– linear horizontal scaling (0.25 ... 4), as well as non-linear horizontal scaling ‘Panorama-vision’
– PAL+ preprocessing
– line-locked clock, data and sync, or 656-output interface
– peaking, contrast, brightness, color saturation and tint for RGB/ YC r C b and CVBS/ S-VHS
– high-quality soft mixer controlled by Fast Blank
– PIP processing for four picture sizes (1/4, 1/9, 1/16 or 1/36 of normal size) with 8-bit resolution
– 15 predefined PIP display configurations and expert mode (fully programmable)
– control interface for external field memory
– I2C-bus interface
– one 20.25-MHz crystal, few external components
– 80-pin PQFP package
14.11.2.Pin Connections and Short Descriptions

NC = not connected
SUPPLYA = 4.75...5.25 V, SUPPLYD = 3.15...3.45 V
Pin No. Pin Name Type Connection Short Description

PQFP (if not used)
80-pin
8 FFRSTWIN IN LV or GNDD FIFO Reset Write Input
9 VSUPCAP OUT X Digital Decoupling Circuitry Supply Voltage
10 VSUPD SUPPLYD X Supply Voltage, Digital Circuitry
11 GNDD SUPPLYD X Ground, Digital Circuitry
12 GNDCAP OUT X Digital Decoupling Circuitry GND
13 SCL IN/OUT X I2C Bus Clock
14 SDA IN/OUT X I2C Bus Data
15 RESQ IN X Reset Input, Active Low
16 TEST IN GNDD Test Pin, connect to GNDD
17 VGAV IN GNDD VGAV Input
18 YCOEQ IN GNDD Y/C Output Enable Input, Active Low
19 FFIE OUT LV FIFO Input Enable
17
20 FFWE OUT LV FIFO Write Enable
21 FFRSTW OUT LV FIFO Reset Write/Read
22 FFRE OUT LV FIFO Read Enable
23 FFOE OUT LV FIFO Output Enable
24 CLK20 IN/OUT LV Main Clock output 20.25 MHz
25 GNDPA OUT X Pad Decoupling Circuitry GND
26 VSUPPA OUT X Pad Decoupling Circuitry Supply Voltage
27 LLC2 OUT LV Double Clock Output
28 LLC1 IN/OUT LV Clock Output
29 VSUPLLC SUPPLYD X Supply Voltage, LLC Circuitry
30 GNDLLC SUPPLYD X Ground, LLC Circuitry
31 Y7 OUT GNDY Picture Bus Luma (MSB)
35 GNDY SUPPLYD X Ground, Luma Output Circuitry
36 VSUPY SUPPLYD X Supply Voltage, Luma Output Circuitry
40 Y0 OUT GNDY Picture Bus Luma (LSB)
41 C7 OUT GNDC Picture Bus Chroma (MSB)
45 VSUPC SUPPLYD X Supply Voltage, Chroma Output Circuitry
46 GNDC SUPPLYD X Ground, Chroma Output Circuitry
50 C0 OUT GNDC Picture Bus Chroma (LSB)
51 GNDSY SUPPLYD X Ground Sync Pad Circuitry
52 VSUPSY SUPPLYD X Supply Voltage, Sync Pad Circuitry
53 INTLC OUT LV Interlace Output
54 AVO OUT LV Active Video Output
55 FSY/HC/HSYA OUT LV Front Sync/ Horizontal Clamp Pulse/Front-End Horizontal
Sync Output
56 MSY/HS IN/OUT LV Main Sync/Horizontal Sync Pulse
57 VS OUT LV Vertical Sync Pulse
58 FPDAT/VSYA IN/OUT LV Front End/Back-End Data/Front-End Vertical Sync Output
59 VSTBYY SUPPLYA X Standby Supply Voltage
60 CLK5 OUT LV CCU 5 MHz Clock Output
61 NC - LV or GNDD Not Connected
62 XTAL1 IN X Analog Crystal Input
63 XTAL2 OUT X Analog Crystal Output
65 GNDF SUPPLYA X Ground, Analog Front-End
66 VRT OUTPUT X Reference Voltage Top, Analog
67 I2CSEL IN X I2C Bus Address Select
68 ISGND SUPPLYA X Signal Ground for Analog Input, connect to GNDF
69 VSUPF SUPPLYA X Supply Voltage, Analog Front-End
70 VOUT OUT LV Analog Video Output
71 CIN IN LV Chroma/Analog Video 5 Input
76 VSUPAI SUPPLYA X Supply Voltage, Analog Component Inputs Front-End
77 GNDAI SUPPLYA X Ground, Analog Component Inputs Front-End
78 VREF OUTPUT X Reference Voltage Top, Analog Component Inputs Front-
End
79 FB1IN IN VREF Fast Blank Input
80 AISGND SUPPLYA X Signal Ground for Analog Component Inputs, connect to
GNDAI
18
14.12.TDA1308T
The TDA1308 is an integrated class AB stereo headphone driver contained in an SO8 or a DIP8 plastic
package. The device is fabricated in a 1 mm CMOS process and has been primarily developed for
portable digital audio applications. It gets its input from two analog audio outputs (DACA_L and
DACA_R) of MSP3411G. The gain of the output is adjustable by the feedback resistor between the
inputs and outputs.
14.12.2.Features
• Wide temperature range
• No switch ON/OFF clicks
• Excellent power supply ripple rejection
• Low power consumption
• Short-circuit resistant
• High performance
• high signal-to-noise ratio
• High slew rate
• Low distortion
• Large output voltage swing.
14.12.3.Pinning

OUTA 1 Output A
INA(neg) 2 Inverting input A
INA(pos) 3 Non-inverting input A
V SS 4 Negative supply
INB(pos) 5 Non-inverting input B
INB(neg) 6 Inverting input B
OUTB 7 Output B
V DD 8 Positive supply
14.13.MSP34X1G (MSP3411G)
14.13.1.Description
The MSP 34x1G family of single-chip Mullet-standard Sound Processors covers the sound processing
of all analog TV -Standards worldwide, as well as the NICAM digital sound standards. The full TV sound
a single chip. Figure shows a simplified functional block diagram of the MSP34x1G. The MSP34x1G
has all functions of the MSP34x0G with the addition of a virtual surround sound feature. Surround
sound can be reproduced to a certain extent with two loudspeakers. The MSP34x1G includes our
virtualizer algorithm “3D-PANORAMA” which has been approved by the Dolby 1) Laboratories for
compliance with the "Virtual Dolby Surround" technology. In addition, the MSP34x1G includes the
“PANORAMA” algorithm. These TV sound processing ICs include versions for processing the multi-
channel television sound (MTS) signal conforming to the standard recommended by the Broadcast
Television Systems Committee (BTSC). The DBX noise reduction, or alternatively, Micronas Noise
Reduction (MNR) is performed alignment free. Other processed standards are the Japanese FM-FM
multiplex standard (EIA -J) and the FM Stereo Radio standard. Current ICs have to perform adjustment
procedures in order to achieve good stereo separation for BTSC and EIA-J. The MSP34x1G has
optimum stereo performance without any adjustments. All MSP 34xxG versions are pin and software
downward compatible to the MSP 34xxD. MSP34x1G further simplifies controlling software. Standard
selection requires a singleI2 C transmission only. The MSP34x1G has built-in automatic functions: The
IC is able to detect the actual sound standard automatically (Automatic Standard Detection).
Furthermore, pilot levels and identification signals can be evaluated internally with subsequent
switching between mono/stereo/bilingual; no I2 C interaction is necessary (Automatic Sound Selection).
19
14.13.2.Features
3D-PANORAMA virtualizer (approved by Dolby Laboratories) with noise generator
PANORAMA virtualizer algorithm
Standard Selection with single I2C transmission
Automatic Standard Detection of terrestrial TV standards/Automatic Carrier Mute function
Automatic Sound Selection (mono/stereo/bilingual), new registers MODUS, STATUS
Two selectable sound IF (SIF) inputs
Interrupt output programmable (indicating status change)
Loudspeaker / Headphone channel with volume, balance, bass, treble, loudness
Loudspeaker channel with MDB (Micronas Dynamic Bass)
AVC: Automatic Volume Correction
Subwoofer output with programmable low-pass and complementary high-pass filter
5-band graphic equalizer for loudspeaker channel
Spatial effect for loudspeaker channel; processing of all deemphasis filtering
Four Stereo SCART (line) inputs, one Mono input; two Stereo SCART outputs
Complete SCART in/out switching matrix
2 2
Two I S inputs; one I S output
All analog FM-Stereo A2 and satellite standards
All analog Mono sound carriers including AM-SECAM L
Simultaneous demodulation of (very) high-deviation FM-Mono and NICAM
Adaptive deemphasis for satellite (Wegener-Panda, acc. to ASTRA specification)
ASTRA Digital Radio (ADR) together with DRP 3510A
All NICAM standards
Korean FM-Stereo A2 standard
NC = not connected; leave vacant
DVSS: if not used, connect to DVSS
AHVSS: connect to AHVSS
Connection
Pin No. Pin Name Type Short Description
(if not used)
PLCC PSDIP PSDIP PQFP PLQFP
68-pin 64-pin 52-pin 80-pin 64-pin
1 16 14 9 8 ADR_WS OUT LV ADR word strobe
3 15 13 8 7 ADR_DA OUT LV ADR Data Output
4 14 12 7 6 I2S_DA_IN1 IN LV I2S1 data input
5 13 11 6 5 I2S_DA_OUT OUT LV I2S data output
20
6 12 10 5 4 I2S_WS IN/OUT LV I2S word strobe
7 11 9 4 3 I2S_CL IN/OUT LV I2S clock
8 10 8 3 2 I2C_DA IN/OUT X I2C data
9 9 7 2 1 I2C_CL IN/OUT X I2C data
11 7 6 80 63 STANDBYQ IN X Stand-by (low -active)
12 6 5 79 62 ADR_SEL IN X I2C bus address select
Audio clock output
18 1 2 74 57 AUD_CL_OUT OUT LV
(18.432 MHz)
19 64 1 73 56 TP LV Test pin
20 63 52 72 55 XTAL_OUT OUT X Crystal oscillator
21 62 51 71 54 XTAL_IN IN X Crystal oscillator
22 61 50 70 53 TESTEN IN X Test pin
AVSS via 56 IF Input 2 (can be left
23 60 49 69 52 ANA_IN2+ IN pF/LV vacant, only if IF input 1 is
also not in use)
AVSS via 56 IF common (can be left
24 59 48 68 51 ANA_IN- IN pF/LV vacant, only if IF input 1 is
also not in use)
25 58 47 67 50 ANA_IN1+ IN LV IF input 2
26 57 46 66 49 AVSUP X Analog power supply 5v
- - - 65 - AVSUP X Analog power supply 5v
- - - 63 48 NC LV Not connected
27 56 45 62 48 AVSS X Analog ground
- - - 61 - AVSS X Analog ground
28 55 44 60 47 MONO_IN IN LV Mono input
Reference voltage IF A/D
29 54 43 58 46 VREFTOP X
converter
39 44 - 48 36 SC4_IN_R IN LV SCART 4 input, right
40 43 - 47 35 SC4_IN_L IN LV SCART 4 input, left
41 - - 46 - NC LV or AHVSS Not connected
42 42 36 45 34 AGNDC X Analog reference voltage
43 41 35 44 33 AHVSS X Analog ground
- - - 43 - AHVSS X Analog ground
44 40 34 40 32 CAPL_M X Volume capacitor MAIN
45 39 33 39 31 AHVSUP X Analog power supply 8V
46 38 32 38 30 CAPL_A X Volume capacitor AUX
48 36 30 36 28 SC1_OUT_R OUT LV SCA RT output 1, right
49 35 29 35 27 VREF X Reference ground 1
52 - - 32 - NC LV Not connected
54 31 26 30 23 DACM_SUB OUT LV Subwoofer output
56 29 25 28 21 DACM_L OUT LV Loudspeaker out, left
57 28 24 27 20 DACM_R OUT LV Loudspeaker out, right
58 27 23 26 19 VREF2 X Reference ground 2
59 26 22 25 18 DACA_L OUT LV Headphone out, left
60 25 21 24 17 DACA_R OUT LV Headphone out, right
61 24 20 21 16 RESETQ IN X Power-on-reset
21
64 21 19 18 13 NC LV Not connected
65 20 18 17 12 I2S_DA_IN2 IN LV I2S2-data input
66 19 17 16 11 DVSS X Digital ground
67 18 16 13 10 DVSUP X Digital power supply 5V
68 17 15 10 9 ADR_CL OUT LV ADR clock
14.14.TL431
14.14.1.Description
The TL431 is a 3-terminal adjustable shunt voltage regulator providing a highly accurate 1 % band gap
reference. TL431 acts as an open-loop error amplifier with a 2.5V temperature compensation reference.
The TL431 thermal stability, wide operating current (150mA) and temperature range (0.to 105.makes it
suitable for all variety of application that are looking for a low cost solution with high performance. The
output voltage may be adjusted to any value between VREF and 36 volts with two external resistors.
The TL431 is operating in full industrial temperature range of 0°C to 105°C. The TL431 is available in
TO-92, SO-8, SOT-89 and SOT23-5 packages.
14.14.2.Features
• Trimmed Band gap to 1%
• Wide Operating Current 1mA to 150mA
• Extended Temperature Range 0. °C to 105.°C
• Low Temperature Coefficient 30 ppm /°C
• Offered in TO -92, SOIC, SOT-89, SOT-23-5
• Improved Replacement in Performance for TL431
• Low Cost Solution
14.15.TDA9885/86
14.15.1.Introduction
The TDA9885 is an alignment-free single standard (without positive modulation) vision and sound IF signal
PLL. The TDA9886 is an alignment-free multi standard (PAL, SECAM and NTSC) vision and sound IF signal
PLL. Both devices can be used for TV, VTR, PC and set-top box applications.
14.15.2.Features
• 5 V supply voltage
• Gain controlled wide-band Vision Intermediate Frequency (VIF) amplifier (AC-coupled)
• Multistandard true synchronous demodulation with active carrier regeneration (very linear demodulation,
good intermodulation figures, reduced harmonics, excellent pulse response)
• Gated phase detector for L/L accent standard
• Fully integrated VIF Voltage Controlled Oscillator (VCO), alignment-free; frequencies switchable for all
negative and positive modulated standards via I2C-bus
• Digital acquisition help, VIF frequencies of 33.4, 33.9, 38.0, 38.9, 45.75 and 58.75 MHz
22
• 4 MHz reference frequency input [signal from Phase-Locked Loop (PLL) tuning system] or operating as
crystal oscillator
• VIF Automatic Gain Control (AGC) detector for gain control, operating as peak sync detector for negative
modulated signals and as a peak white detector for positive modulated signals
• Precise fully digital Automatic Frequency Control (AFC) detector with 4-bit digital-to-analog converter; AFC
bits via I2C-bus readable
• Take Over Point (TOP) adjustable via I2C-bus or alternatively with potentiometer
• Fully integrated sound carrier trap for 4.5, 5.5, 6.0 and 6.5 MHz, controlled by FM-PLL oscillator
• Sound IF (SIF) input for single reference Quasi Split Sound (QSS) mode (PLL controlled)
• SIF AGC for gain controlled SIF amplifier; single reference QSS mixer able to operate in high performance
single reference QSS mode and in intercarrier mode, switchable via I2C-bus
• AM demodulator without extra reference circuit
• Alignment -free selective FM-PLL demodulator with high linearity and low noise
• I2C-bus control for all functions
• I2C-bus transceiver with pin programmable Module Address (MAD).
Symbol Pin Description

VIF1 1 VIF differential input 1
VIF2 2 VIF differential input 2
OP1 3 output 1 (open-collector)
FMPLL 4 FM-PLL for loop filter
DEEM 5 de-emphasis output for capacitor
AFD 6 AF decoupling input for capacitor
DGND 7 digital ground
AUD 8 audio output
TOP 9 tuner AGC TakeOver Point (TOP)
SDA 10 I2C-bus data input/output
SCL 11 I2C-bus clock input
SIOMAD 12 sound intercarrier output and MAD select
n.c 13 not connected
TAGC 14 tuner AGC output
REF 15 4 MHz crystal or reference input
VAGC 16 VIF-AGC for capacitor (Not connected for TDA9885.)
CVBS 17 video output
AGND 18 analog ground
VPLL 19 VIF-PLL for loop filter
VP 20 supply voltage (+5 V)
AFC 21 output
OP2 22 output 2 (open-collector)
SIF1 23 differential input 1
SIF2 24 differential input 2
14.16.LM7808
14.16.1.Description
The L7800 series of three-terminal positive regulators is available in TO -220 TO -220FP TO-3 and D 2
PAK packages and several fixed output voltages, making it useful in a wide range of applications.
These regulators can provide local on-card regulation, eliminating the distribution problems associated
with single point regulation. Each type employs internal current limiting, thermal shutdown and safe
area protection, making it essentially indestructible. If adequate heat sinking is provided, they can
deliver over 1A output current. Although designed primarily as fixed voltage regulators, these devices
can be used with external components to obtain adjustable voltages and currents.
14.16.2.Features
Output Current Up To 1.5 A
Output Voltages of 5; 5.2; 6; 8; 8.5; 9; 12; 15; 18; 24V
Thermal Over load protection
Output Transition SOA Protection
23
14.17.TDA8177F
14.17.1.Description
Designed for monitors and high performance TVs, the TDA8177F vertical deflection booster can handle
flyback voltage up to 70V. More than this it is possible to have a flyback voltage, which is more than the
double of the supply (Pin 2). This allows to decrease the power consumption or to decrease the flyback
time for a given supply voltage. The TDA8177F operates with supplies up to 35V and provides up to
3APP output current to drive the yoke.
14.17.2.Features
Power Amplifier
Thermal Protection
Output Current Up To 3.0APP
Flyback Voltage Up To 70V (on Pin 5)
Suitable For Dc Coupling Application
External Flyback Supply
14.17.4.Block Diagram
14.18.LM1086
14.18.1.Description
The LM1086 is a series of low dropout positive voltage regulators with a maximum dropout of 1.5V at
1.5A of load current. It has the same pin-out as National Semiconductor’s industry standard LM317.
The LM1086 is available in an adjustable version, which can set the output voltage with only two
external resistors. It is also available in five fixed voltages: 2.5V, 2.85V, 3.3V, 3.45V and 5.0V. The fixed
versions integrate the adjust resistors. The LM1086 circuit includes a zener trimmed band-gap
reference, current limiting and thermal shutdown.
14.18.2.Features
Available in 2.5V, 2.85V, 3.3V, 3.45V, 5V and Adjustable Versions
Current Limiting and Thermal Protection
Output Current 1.5A
24
Line Regulation 0.015% (typical)
Load Regulation 0.1% (typical)
SCSI-2 Active Terminator
High Efficiency Linear Regulators
Battery Charger
Post Regulation for Switching Supplies
Constant Current Regulator
Microprocessor Supply
14.18.4.Connection Diagrams
14.19.MC44608
14.19.1.Description
The MC44608 is a high performance voltage mode controller designed for off–line converters. This high
voltage circuit that integrates the start–up current source and the oscillator capacitor, requires few
external components while offering a high flexibility and reliability. The device also features a very high
efficiency stand–by management consisting of an effective Pulsed Mode operation. This technique
enables the reduction of the stand–by power consumption to approximately 1W while delivering 300mW
in a 150W SMPS.
• Integrated Start–Up Current Source
• Lossless Off–Line Start–Up
• Direct Off–Line Operation
• Fast Start–Up
14.19.2.General Features
• Flexibility
• Duty Cycle Control
• Under voltage Lockout with Hysteresis
• On Chip Oscillator Switching Frequency 40, or 75kHz
• Secondary Control with Few External Components
Protections
• Maximum Duty Cycle Limitation
• Cycle by Cycle Current Limitation
• Demagnetization (Zero Current Detection) Protection
• “Over VCC Protection” Against Open Loop
• Programmable Low Inertia Over Voltage Protection Against Open Loop
• Internal Thermal Protection
TM
GreenLine Controller
• Pulsed Mode Techniques for a Very High Efficiency Low Power Mode
• Lossless Startup
• Low dV/dT for Low EMI Radiations
25
14.19.3.Pin Connections
14.19.4.Pin Function description
Pin Name Description

1 Demag The Demag pin offers 3 different functions: Zero voltage crossing detection (50mV),
24mA current detection and 120mA current detection. The 24mA level is used to detect
the secondary reconfiguration status and the 120mA level to detect an Over Voltage
status called Quick OVP.
2 ISENSE The Current Sense pin senses the voltage developed on the series resistor inserted in
the source of the power MOSFET. When I sense reaches 1V, the Driver output (pin 5)
is disabled. This is known as the Over Current Protection function. A 200mA current
source is flowing out of the pin 3 during the start–up phase and during the switching
phase in case of the Pulsed Mode of operation. A resistor can be inserted between the
sense resistor and the pin 3; thus a programmable peak current detection can be
performed during the SMPS stand–by mode.
3 Control Input A feedback current from the secondary side of the SMPS via the opto–coupler is
injected into this pin. A resistor can be connected between this pin and GND to allow
the programming of the Burst duty cycle during the Stand–by mode.
4 Ground This pin is the ground of the primary side of the SMPS.
5 Driver The current and slew rate capability of this pin are suited to drive Power MOSFETs.
6 VCC This pin is the positive supply of the IC. The driver output gets disabled when the
voltage becomes higher than 15V and the operating range is between 6.6V and 13V.
An intermediate voltage level of 10V creates a disabling condition called Latched Off
phase.
7 This pin is to provide isolation between the Vi pin 8 and the VCC pin 6.
8 Vi This pin can be directly connected to a 500V voltage source for start–up function of the
IC. During the Start–up phase a 9 mA current source is internally delivered to the VCC
pin 6 allowing a rapid charge of the VCC capacitor. As soon as the IC starts –up, this
current source is disabled.
14.20.TCET1102G
14.20.1.Description
The TCET110/ TCET2100/ TCET4100 consists of a phototransistor optically coupled to a gallium
arsenide infrared-emitting diode in a 4-lead up to 16-lead plastic dual inline package. The elements are
mounted on one lead frame using a coplanar technique, providing a fixed distance between input and
output for highest safety requirements.
Circuits for safe protective separation against electrical shock according to safety class II (reinforced
isolation):
For appl. class I – IV at mains voltage =300 V
For appl. class I – III at mains voltage =600 V
According to VDE 0884, table 2, suitable for: Switch-mode power supplies, line receiver, computer
peripheral interface, microprocessor system interface.
14.20.3.Features
VDE 0884 related features:
Rated impulse voltage (transient overvoltage) V IOTM = 8 kV peak
Isolation test voltage (partial discharge test voltage) V pd = 1.6 kV
Rated isolation voltage (RMS includes DC) V IOWM = 600 V RMS (848 V peak)
Rated recurring peak voltage (repetitive) V IORM = 600 V RMS
26
General features:
CTR offered in 9 groups
Isolation materials according to UL94-VO
Pollution degree 2 (DIN/VDE 0110 / resp. IEC 664)
Climatic classification 55/100/21 (IEC 68 part 1)
Special construction: Therefore, extra low coupling capacity of typical 0.2pF, high Common Mode
Rejection
Low temperature coefficient of CTR
G = Leadform 10.16 mm; provides creepage distance > 8 mm, for TCET2100/ TCET4100 optional;
suffix letter ‘G’ is not marked on the optocoupler
Coupling System U
14.21.TDA7480L
14.21.1.Description
The TDA7480L is an audio class-D amplifier assembled in Power DIP package specially de-signed for
14.21.2.Features
10W Output Power: RL = 8Ω/4Ω; THD = 10%
High Frequency
No Heatsink
Split Supply
Overvoltage Protection
St-By And Mute Features
Thermal Overload Protection
14.21.3.Pin Functions
Number Name Function

4 OUT PWM OUTPUT
5 BOOTDIODE BOOTSTRAP DIODE ANODE
6 BOOT BOOTSTRAP CAPACITOR
7 NC NOT CONNECTED
8 FEEDCAP FEEDBACK INTEGRATING CAPACITANCE
9 FREQUENCY SETTING FREQUENCY RESISTOR
10 SGN-GND SIGNAL GROUND
11 IN INPUT
12 ST-BY-MUTE ST-BY/ MUTE CONTROL PIN
13 NC NOT CONNECTED
14 +VCC SIGN POSITIVE SIGNAL SUPPLY
15 VREG 10V INTERNAL REGULATOR
16 +VCC POW POSITIVE POWER SUPPLY
17 -VCC NEGATIVE SUPPLY (TO BE CONNECTED TO PIN 16 VIA C5)
14.22.SAA3010T
14.22.1.Description
The SAA3010 is intended as a general purpose (RC-5) infrared remote control system for use where a low
voltage supply and a large debounce time are expected. The device can generate 2048 different commands
and utilizes a keyboard with a single pole switch for each key. The commands are arranged so that 32
systems can be addressed, each system containing 64 different commands. The circuit response to legal
(one key pressed at a time) and illegal (more than one key pressed at a time) keyboard operation is specified
in the section “Keyboard operation”.
27
14.22.2.Features
Low voltage requirement
Biphase transmission technique
Single pin oscillator
Test mode facility
14.22.3.Pinning
Pin Mnemonic Function

1 X7 (IPU) sense input from key matrix
2 SSM (I) sense mode selection input
3 Z0-Z3 (IPU) sense inputs from key matrix
7 MDATA (OP3) generated output data modulated with 1/12 the oscillator frequency at a 25% duty factor
8 DATA (OP3) generated output information
9-13 DR7- DR3 (ODN) Scan drivers
14 VSS Ground (0V)
15-17 DR-2- DR0 (ODN) Scan drivers
18 OSC (I) Oscillator input
19 TP2 (I) test point 2
20 TP1 (I) Test point 1
21-27 X0-X6 (IPU) Sense inputs from key matrix
28 VDD(I) Voltage supply
Note:
(I): Input,
(IPU): input with p-channel pull-up transistor,
(ODN): output with open drain n-channel transistor
(OD3): output 3-state
28
15.AK52 CHASSIS MANUAL ADJUSTMENTS PROCEDURE
15.1.PRELIMINARY
Before starting with the alignment procedure, make sure that all the potentiometers on the chassis and
also screen and focus pots are in the medium position.
15.2.SYSTEM VOLTAGE ADJUSTMENTS

Inputs AC power (220V 50Hz)
PAL B/G test pattern via RF
(PAL I test pattern for PAL I TV’s, SECAM D/K pattern, SECAM L/L’/K’ TVs.)
Outputs Digital voltmeter to anode of D110.
Display System voltage
Action Apply power. Check that the stand-by Led lights.
Select TV mode and tune to the applied test pattern via local test keyboard.
Chassis should start normally.
Adjust all analog controls (volume, bass, treble, brightness, contrast, colour) to minimum
settings.
Adjust VR127 according to the following different type of CRTs.
SYSTEM VOLTAGE TYPE OF CRT

135V±0.5V VIDEOCOLOR A66ECY13X12
135V±0.5V PHILIPS W66ESF002X44
15.3.AFC ADJUSTMENTS
AFC is automatically adjusted from software , when f (IF) is selected 38.9MHz for
negative modulation and 33.9MHz for positive modulation from the service menu.
15.4.FOCUS ADJUSTMENTS
Inputs AC power
PAL B/G test pattern via RF input.
Outputs Picture tube drive.
Display Picture
Action Select TV mode and tune to the signal.
Adjust focus potantiometer (the upper pot on the rear side of the FBT transformer) for
optimum focusing drive.
15.5.SCREEN ADJUSTMENTS
Inputs AC power
PAL B/G Colour Bar test pattern via RF
Outputs 1/100 Oscilloscope probe to RGB cathodes on CRT baseboard.
st
NOTE: Ground pin of probe will be connected to 1 pin (GND) of the CRT socket.
Display RGB ratio
Action Select PAL B/G Colour bar pattern using the local test keyboard and the user remote
control unit.
Adjust all control functions (brightness, colour and contrast) to minimum settings.
Measure the most sensitive cathode
Adjust the screen potentiometer (lower pot on the rear side of FBT transformer) until
cathode voltage becomes 150V.
15.6.IF ADJUSTMENT FOR L’ MODE
AFC is automatically adjusted from software , when f (IF) is selected 33.9MHz for
positive modulation (SECAM L’) from the service menu.
16.AK52 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS
29
16.1.PRELIMINARY
All system, geometry and white balance alignments are performed in production service mode. Before
starting the production mode alignments, make sure that all manual adjustments are done correctly. To
start production mode alignments enter the MAIN MENU and then press the digits 1, 6, 7 and 5
respectively. The following first menu appears on the screen. Production mode values will appear on
the screen.
PRODUCTION OK> STORE MENU EXIT PRODUCTION OK> STORE MENU EXIT
H/V VIDEO ADJUSTMENTS OPTIONS

VSHIFT 000 WdR 064 PIP CNTRST 000 0.HPHONE ON
V-SIZE 0068 WdG 064 PIP Ydelay 000 1.CRT 4:3
H-SHIFT 1218 WdB 064 PIP Frame 0 2.SVHS OFF
H-SIZE 012 CuR 064 EHTHP 001 3.f(IF) 38.9
S-COR 027 CuG 064 EHTH TC 000 4.Türk. ON
LINRT -01 CuB 064 EHTH -36 5.VGA OFF
ANGLE 001 YDFP -05 EHTV -14 6.FRONT ON
BOW -03 AGC 009 EHTV TC 005 7.DPL OFF
TRPEZ -07 TLAN W-T SVDEL 008 8.VD ON
PARAB -46 APS ON BCLTHR (mA) 1.1 9.NSL ON
U.COR 001 T_T THO OSD CONT 055 A.PAP OFF
L.COR 008 T_P SAM OSD BRI 040 B.CTI ON
TILT 049 YDFS -07 TEXT BRI 050 C.AVL OFF
TRPZD 020 YDFN -02 PIP YDelSe 000
INIT NVM SYSTEM
NTSCHS 000 EXT3 ON
TXTV 015 DVD OFF 0.PAL B/G ON
Prescaler 1.PAL D/K OFF
C.M ON
AK52 A032 T2 FM 027 2.PAL I OFF
BLUE OFF
08.10.2002 NICAM 061 3.SECAM B/G ON
4:3 000
I2S 016 4.SECAM D/K OFF
OVM ON
AGC READ SCART 025 5.SECAM L/L OFF
-10 SERVICE 6.AUST. OFF
First page Second Page
SERVICE MENU
Production mode groups will be displayed with different colours of headlines, so in order to access a
production alignment group press the colour button of the related group on the remote control
transmitter.
• RED BUTTON is pressed to access H/V menu.
• GREEN BUTTON is pressed to access VIDEO adjust menu.
• BLUE BUTTON is pressed to go to the next page of the service menu.
• YELLOW BUTTON is used to adjust system parameters on the second page of the service menu.
After selecting one of the production service mode groups, you can access its items by pressing ? /?
buttons. Selected parameter will be highlighted. Inorder to change the selected parameter, use ? / ?
buttons. Inorder to switch between other group of items press the colour key of this groups headline.
To store the settings press OK button. To exit the service menu press MENU button.
Entire service menu parameters of AK52 CHASSIS are listed below.
16.2.H/V (HORIZONTAL AND VERTICAL GEOMETRY ALIGNMENTS)

Switch the program to crosshatch test pattern. Press RED button to access this group of item. Select
the settings by pressing OK button. Switch the another parameter group by pressing the colour button
of the related coloured headline of that group. Exit production mode by pressing the MENU button on
the remote control.
V-SHIFT
Change Vertical Shift by pressing Left/Right buttons till the test pattern is vertically centered. Horizontal
line at the center of the test pattern is in equal distance both to upper and lower side of the picture tube.
Check and readjust V-SHIFT item if the adjustment becomes improper after some other geometric
adjustments are done.
Min. Value: -128
Max. Value: 127
30
V-SIZE
Change Vertical Size by pressing Left/Right buttons till horizontal black lines on both the upper and
lower part of the test pattern become very close to the upper and lower horizontal sides of picture tube
and nearly about to disappear. Check and readjust V-SIZE item if the adjustment becomes improper
after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
H-SHIFT
Change Horizontal Shift by pressing Left/Right buttons till the the test pattern is horizontally in equal
distance both to right and left sides of the picture tube. Check and readjust H-SHIFT item if the
adjustment becomes improper after some other geometric adjustments are done.
Min. Value: 0000
Max. Value: 1295
H-SIZE
Change Horizontal Size by pressing Left/Right buttons till no under-scan condition will happen, i.e. no
white bars on the left and right side of the test pattern will be visible nor picture will be so wide. Check
and readjust H-SIZE item if the adjustment becomes improper after some other geometric adjustments
are done.
Min. Value: -128
Max. Value: 127
S-COR
Change S-Correction by pressing Left/Right buttons till the size of squares on both the upper and lower
part of test pattern become equal to the squares laying on the vertical center of the test pattern. Check
and readjust S-COR item if the adjustment becomes improper after some other geometric adjustments
are done.
Min. Value: -128
Max. Value: 127
LINRT
Change Linearity by pressing Left/Right buttons till all the size of squares of the test pattern become in
equal size from the top of the screen to its bottom of the whole screen. Check and readjust LINRT item
if the adjustment becomes improper after some other geometric adjustments are done. (especially after
than S-COR adjustment)
Min. Value: -128
Max. Value: 127
ANGLE
Change Angle by pressing Left/Right buttons till the vertical lines of the crosshatch pattern become
completely perpendicular to horizontal lines without any angle of vertical deviation. Check and readjust
ANGLE item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
BOW
Change Bow by pressing Left/Right buttons till the vertical lines especially ones close to the left and
right sides will of equal and symmetrical bending, i.e. they together will neither be towards left side nor
right side. Check and readjust BOW item if the adjustment becomes improper after some other
Min. Value: -128
31
Max. Value: 127
TRPEZ
Change Trapezium by pressing Left/Right buttons till vertical lines, especially lines at the sides of the
picture frame became parallel to the both sides of picture tube as close as possible. Check and readjust
TRPEZ item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
PARAB
Change Parabol by pressing Left/Right buttons till vertical lines close to the both sides of the picture
frame become parallel to vertical sides of picture tube without any bending to left or to right side of the
screen. Check and readjust PARAB item if the adjustment becomes improper after some other
Min. Value: -128
Max. Value: 127
U.COR
Change Upper Correction by pressing Left/Right buttons till vertical lines at the upper corners of the
U.COR item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
L.COR
Change Lower Correction by pressing Left/Right buttons till vertical lines at the lower corners of the
L.COR item if the adjustment becomes improper after some other geometric adjustments are done.
Min. Value: -128
Max. Value: 127
TILT
This adjustment only works when the TV has rotation option. Change TILT by pressing Left/Right
buttons to rotate the complete raster clock-wise and counter clock-wise depending on the CRT. Check
are done.
Min. Value: 000
Max. Value: 063
TRPZD
Not used for this model.
NTSCHS
Change NTSC horizontal size by pressing Left/Right buttons to adjust till no under-scan condition will
happen, i.e. no white bars on the left and right side of the NTSC test pattern will be visible nor picture
will be so wide. Check and readjust TRPEZ item if the adjustment becomes improper after some other
Min. Value: 000
Max. Value: 010
TXTV
Change TXTV by pressing Left/Right buttons to adjust the proper vertical size of Teletext screen. Check
are done.
32
Min. Value: 000
Max. Value: 040
16.3.VIDEO ALIGNMENTS
Switch the program to colour bar test pattern. Press GREEN button to access this group of item. Select
the settings by pressing OK button.
WdR, WdG, WdB: WHITE BALANCE ADJUSTMENT

Apply WHITE test pattern via RF. Adjust all analog functions to medium level and set WdR to 86, WdG
to 84, WdB to 80, if needed. Use colour analyser and monitor the colour temperature (X,Y) on colour
analyser. Select WdR and WdB by pressing up/down buttons and change the values by Left/Right
buttons till the following values are read:
X=285±10
Y=293±10 on the colour analyser.
CuR, CuG, CuB

Set the values of these items as 64 (constant).
YDFP
Enter a PAL B/G colour and black-white bar test pattern via RF. Adjust Y-Delay for PAL till the colour
Min. Value: -07
Max. Value: 001
AGC
Apply PAL BG signal, VHF-3 Channel-12 and 60dBuV signal level. Adjust AGC (Automatic Gain
Control) item by pressing Left/Right buttons till the voltage at AGC point (pin1 of the tuner) becomes 3.0
volts.
Min. Value: 000
Max. Value: 031
TLAN
Text language is set. Options are W-T, W-E, W, E. W-T will be selected.
APS
The option of APS (Automatic Program Searching) item are ON and OFF. In order to active APS
installation procedure when TV is turned for the very first time, select ON. Inorder to start TV without
APS installation procedure, select OFF.
T_T
This item is used for the Tuner selection. The options are SAM for SAMSUNG, THO for THOMSON,
SIE for SIEMENS, MK2 and MK3 for PHILIPS MP2/MP3, ALP for ALPS and TEC for Tecnisat. Select
THO.
T_P
This item is also used for the Tuner selection. The options are MK2, SAM, THO, TEM. MK2 for
PHILIPS, SAM for SAMSUNG, THO for THOMSON and TEM for TEMIC. Select SAM.
YDFS
Enter a SECAM B/G colour and black-white bar test pattern via RF. Adjust Y-Delay SECAM till the
colour transients on the colour bar of the pattern become as sharper and colours between transients do
not mix with each other as possible.
Min. Value: -07
Max. Value: 001
33
YDFN
Enter an NTSC colour and black-white bar test pattern via RF. Adjust Y-Delay NTSC till the colour
Min. Value: -07
Max. Value: 001
EXT3
Select ON.
DVD
Select OFF.
C.M
Select ON.
BLUE
Select OFF.
4:3
Set to 0.
OVM
Select ON.
16.4.SERVICE ALIGNMENTS
IMPORTANT: There will no adjustments in this service mode during production mode alignments.
Press BLUE colour button on the remote control when Production mode is active. Press the colour
button of the related item group headline colour. Press up/down buttons to select the item of group.
Press Left/Right button to alter the value of the item. Press OK button to store the selected value and
MENU button to exit the service alignments mode.
ADJUSTMENTS GROUP
Press RED button in order to access this group of items.
PIP CNTRST : Level of the PIP picture
PIP Ydelay : Luma delay of the PIP picture
PIP Frame : Colour selection of the PIP frame (edges of the PIP)
EHTHP : EHT compensation coefficient for horizontal phase
EHTH TC : EHT time constant for horizontal phase compensation
EHTH : EHT compensation coefficient for horizontal amplitude
EHTV : EHT compensation coefficient for vertical amplitude
EHTV TC : EHT time constant for control of vertical and horizontal amplitude EHT
compensation
SVDEL : Delay adjustment for scan velocity modulation
BCLTHR (mA) : Beam current applied to the CRT
OSD CONT : Contrast level of OSD
OSD BRI : Brightness level of OSD
TEXT BRI : Brightness level of text
PIP YDelSe : Y-Delay adjustment for pin-in-picture option
INIT NVM : Press to initiate the NVM
PRESCALER GROUP
Press GREEN button in order to access this group of items.
FM : This adjustment is to determine the pre-amplifier gain of MSP for German stereo
Set to 27.
NICAM : This adjustment is to determine the pre-amplifier gain of MSP for Nicam
Set to 61.
I2S : Not used.
SCART : This adjustment is to determine the pre-amplifier gain of MSP for Scart audio inputs
Set to 25.
34
OPTIONS GROUP
Press BLUE button in order to access this group of items.
0.HPHONE : ON/OFF
1.CRT : 4:3 / 16:9
2.SVHS : ON/OFF
3.f(IF) : always set to 38.9
4.Türk. : Turkish menu ON/OFF
5.VGA : ON/OFF
6.FRONT : Front AV ON/OFF
7.DPL : ON/OFF
8.VD : ON/OFF
9.NSL : ON/OFF
A.PAP : ON/OFF
B.CTI : ON/OFF
C.AVL : ON/OFF
SYSTEM GROUP
Press YELLOW button in order to access this group of items.
0.PAL B/G : ON/OFF
1.PAL D/K : ON/OFF
2.PAL I : ON/OFF
3.SECAM B/G : ON/OFF
4.SECAM D/K : ON/OFF
5.SECAM L/L’ : ON/OFF
6.AUST. : ON/OFF
NOTE: Settings values in Service menu are given for 28” 4:3 THOMSON (A66EHJ13X12) tube in this
manual.
35
17.BLOCK DIAGRAM
Saw Filter
Sound
GENERAL BLOCK DIAGRAM OF
11 AK 52 150V/160V
Saw Filter
TDA
Video
MAIN TUNER +22V
9885/86
(PLL) +14V
SMPS
MC 44608 +14V(audio)
Feature Box Module (MOTOROLA) -14V(audio)
+ +8V
ACTIVE PFC
+5V
MC 33260
(MOTOROLA) +3.3V
Saw Filter
PIP TUNER TDA +3.3V (ST-BY)
9885/86 SDA
(PLL) +2.5V(ST-BY)
D0-D7 SCL 24W32 +12
8
(E 2PROM)
PIP OPTION
27W401 SDA5550M
(EPROM) (MicroController)
A0-A18
18
A0-A18
18
SRAM HORIZONTAL
30KV
12V
Horz. FOCUS
Yoke
SCREEN
Lin. +130V
HORZ. Heater
IF_CVBS
DRIVE
TXT_CVBS E/W E/W
U/V DRIVE -Vert.Sup

EW
LUMA LUMA
8 -Vert.Sup
RGB, FB 8 YUV
30KV
CHROMA CHROMA CRT BOARD
DDP3315C
VPC3230D SDA9400 Heater G2 FOCUS
OSD
TDA6109
RGB,FB VERT+
RGB_OUT
VERT-
SWM
3 SENSE COIL
SVM
R
C
G
PIP_CVBS_
B VERTICAL STAGE
Y/CVBS
EXT
C
BSVM
TDA8177F Vert.
Yoke
(VERT. OUT)
SCART2 RGB
TEA6415C
(Video Switching 3
Matrix)
SCART 3/ HEADPHONE
Front_AV SVHS
SCART1 RGB SCART 1 SCART 2 Back_AV L
TDA1308
R
3 AUDIO AMPLIFIER L
SVHS_C
SC1
SC2
SVHS_Y
TDA 7480
SDA
SCL
IF
Back_V Back_A Front_V Front_A SC2_R(Scart2_C)

Center 8 ohm
C
12W
S3
SDA9488 R
SCL
SDA
S1 S2 MONO IN QSS Surround
2
8 ohm
PIP_CVBS C_SW 12W
AUDIO AMPLIFIER C
QSS 8 ohm
MSP 34XX TDA 7480
SCART 2 12W
RGB,FB
MAIN_R SR
8 ohm
MONO IN L R
PI5V330 12W
(RGB
DVD RGB,FB
SWITCH)
DVD
MAIN_L
11AK52 BLOCK SCHEME
OPTION
25.12.2002
36
18.CIRCUIT DIAGRAMS
11ak52b4-VIDEO
37
11ak52b4-2
38
11ak52b4-3
39
11ak52b4-4
40
11fb2a3—1
41
11fb2a3—2
42
11fb2a3—3
43
11fb2a3—4
44
11uk06-1
45
11txt52-4
46
11rs52
47
11fav19a4
48
11ir2872
11tk109
49
11sb18-3
50
11tk117
11tk118
51
11tp52-1
52
11df41j-2
53
Schematics
AK52-1
AK52-B2
AK52-B4
FB52-A1
FB52-A3
TP52-1
TXT52
Parts List
BILL OF MATERIAL LIST
10020020 2841 TOSHIBA TOSHIBA 28H37G(AK52)SILVER
NO COMPONENT CODE
MATERIAL UNIT QTY POSITION NUMBER
1 20000586 SPK.A.28"-32"(16:9)/72XX/74XX w/FER(W/HE PC 1,000 . . . . .
2 20039751 SPK.AS.7289/99 721X/20/70/71 (L)19 W/HE PC 1,000 . . . . .
3 30000426 CAP EL 6.8UF 50V M (BPL) PC 1,000 . . . . .
4 30001946 SPEAKER 8R 15W 57*160 PC 1,000 . . . . .
5 30001947 TWEETER 8R 15W CLOSED PC 1,000 . . . . .
6 30002238 CABL 2P/200 SPK DIS UL1672AWG24 PC 1,000 . . . . .
7 30012632 CNAS 2P/690 DIS W/C+FER UL2547 AWG24 PC 1,000 . . . . .
8 50011720 LABEL HIGH END PC 1,000 . . . . .
9 20039752 SPK.AS.7289/99 721X/20/70/71 (R)19 W/HE PC 1,000 . . . . .
10 30000426 CAP EL 6.8UF 50V M (BPL) PC 1,000 . . . . .
11 30001946 SPEAKER 8R 15W 57*160 PC 1,000 . . . . .
12 30001947 TWEETER 8R 15W CLOSED PC 1,000 . . . . .
13 30002238 CABL 2P/200 SPK DIS UL1672AWG24 PC 1,000 . . . . .
14 30012631 CNAS 2P/760 DIS W/BL C+FER UL2547 AWG24 PC 1,000 . . . . .
15 50011720 LABEL HIGH END PC 1,000 . . . . .
16 20085192 ON/OFF SW ASSY.19Y FTZ(TOSHIBA)25-28"4:3 PC 1,000 . . . . .
17 30002174 SWITCH ON/OFF 4A/64A PC 1,000 . . . . .
18 30002368 CNAS 2P/650 AC MAINS W/C PC 1,000 . . . . .
19 30016513 POWER CORD 2.2MT JVC (W/FILTER) PC 1,000 . . . . .
20 40000127 SWITCH INSULATION DOOR LK101 PC 1,000 . . . . .
21 40001898 MACARON (12cm.Isý ile daralan) PC 1,000 . . . . .
22 20095506 BASE 2840-41-42 (I)28"(4:3) WO/TESLA TÜP PC 1,000 . . . . .
23 60000008 HIPS (NATURAL) KG 0,838 . . . . .
24 60000022 MASTERBATCH (BLACK) KG 0,004 . . . . .
25 20097393 SNOW BOX ASSY 284X 4:3 PC 1,000 . . . . .
26 20095507 SNOW BOX TOP 284X PC 1,000 . . . . .
27 60000011 EPS KG 0,549 . . . . .
28 20095508 SNOW BOX BOTTOM 284X PC 1,000 . . . . .
29 60000011 EPS KG 0,549 . . . . .
30 20106208 BUTTON AS.2841-2841W-3241W-2441W(SILVER) PC 1,000 . . . . .
31 20094341 LENS LED XX41 (I) MILKY PC 1,000 . . . . .
32 60000008 HIPS (NATURAL) G 0,014 . . . . .
33 60000927 CRYSTAL PS (NATURAL) G 7,000 . . . . .
34 20094352 LENS PRE-AMP XX41 (I) PC 1,000 . . . . .
35 60000927 CRYSTAL PS (NATURAL) G 0,002 . . . . .
36 20106209 BUTTON ON/OFF XX41 SILVER(P) PC 1,000 . . . . .
37 20106210 BUTTON ON/OFF XX41 EKO.GRAY(I) PC 1,000 . . . . .
38 60000001 ABS (NATURAL) KG 0,005 . . . . .
39 60001195 MASTERBATCH EKO.GRAY GR 3216 SE1 G 0,026 . . . . .
40 60000895 PAINT SILVER 022-6485 (SU BAZLI)L8341413 KG 0,002 . . . . .
41 20106211 BUTTON FUNCTION XX41 SILVER(P) PC 1,000 . . . . .
42 20106222 BUTTON FUNCTION XX41 EKO.GRAY(I) PC 1,000 . . . . .
43 60000001 ABS (NATURAL) KG 0,020 . . . . .
46 20108360 BUTTON FUNCT.XX42/42W/43W/44W EKO.GR(I)# PC 1,000 . . . . .
47 60000001 ABS (NATURAL) KG 0,018 . . . . .
49 35000013 SPRING ON/OFF SWITCH PC 1,000 . . . . .
50 20106228 BACK CVR.2841/42/44 W/SB(UL)SILVER(P)4:3 PC 1,000 . . . . .
51 20106227 BACK C.2841/42/44 W/SB(UL)EKO.GRAY(I)4:3 PC 1,000 . . . . .
52 60000009 FR-HIPS NATR.V-0 KG 2,413 . . . . .
55 20108637 CN.ASY.52A-TRFPFC 1,7 A E54 + CONN 2/35 PC 1,000 . . . . .
56 30018087 CNAS 2P/350 TRFPFC DIS W/C UL1672AWG22 PC 1,000 . . . . .
57 30018270 TRF PFC 1,7A 43MH 170W PC 1,000 . . . . .
58 35000217 SCREW S C SYF YFMB 3.5*9.5 PC 1,000 . . . . .
59 20111996 CRT KIT (28") AK52 W/FTZ PC 1,000 . . . . .
60 30002728 28 DEG.COIL&EARTH C.WO/UL FTZ1 PC 1,000 . . . . .
61 30016483 CNAS 2P/600 HRZ DIS W/C UL1672AWG24 PC 1,000 . . . . .
62 30019083 CNAS 2P/600 SIS W/C+FER UL1007AWG24 PC 1,000 . . . . .
63 35000010 EARTH SPRING (4CM) PC 1,000 . . . . .
64 20114688 EXP.KIT AK37 284X-284XW (V.0) TOSHIBA PC 1,000 . . . . .
65 20004520 CABLE HOLDER DX15 (I) PC 1,000 . . . . .
66 60000991 KIRMA - HDPE KG 0,003 . . . . .
67 20084045 STRAP TIE (L:118) PC 1,000 . . . . .
68 60000018 COPOLYMER POLYPROPYLENE KG 0,001 . . . . .
69 20085269 CABLE HOLDER CRT (I) UL94V-0 PC 2,000 . . . . .
70 60000855 KIRMA FR-ABS BLUE CRT KG 0,002 . . . . .
71 40006731 ISOLATION COTTON (9x25000mm) M 1,800 . . . . .
72 70000331 ADHESIVE TAPE 75MM/660M (4125) M 2,592 . . . . .
73 20118835 MD.ASY.TK127-XX41-41W 5SW WO/DVD AK52 PC 1,000 . . . . .
75 30002181 SWITCH TACT PC 5,000 SW1 SW2 SW3 SW4 SW5
76 30019674 LED RED ORANGE 5MM ULTRA BRIGHT PC 2,000 LD1 LD2 . . .
77 30020822 CNAS 6P/450 FLT W/C+FER UL2468AWG24 PC 1,000 PL1 . . . .
78 40000084 BRACKET & PREAMPLIFIER PC 1,000 IC1 . . . .
83 30000459 RES CF 1/4W 100R J PC 1,000 R7 . . . .
84 30000526 RES CF 1/4W 1.5K J PC 1,000 R2 . . . .
85 30000622 RES CF 1/4W 270R J PC 1,000 R5 . . . .
86 30000689 RES CF 1/4W 3.9K J PC 1,000 R1 . . . .
87 30000712 RES CF 1/4W 470R J PC 1,000 R4 . . . .
88 30000718 RES CF 1/4W 4.7K J PC 1,000 R6 . . . .
89 30000770 RES CF 1/4W 680R J PC 1,000 R3 . . . .
91 30022893 PCB 11TK127-6 PC 1,000 . . . . .
92 30000371 CAP EL 22UF 50V M PC 1,000 C1 . . . .
93 30001455 TR BC558B PC 1,000 Q1 . . . .
94 20121334 CRT B.ASSY.TP52E-SING.FOC.(AK52) PC 1,000 . . . . .
100 20121300 CRT B.ASSY.TP52E-PER COMMON AK52 PC 1,000 . . . . .
101 35000176 EYELET BR 2*3MM PC 2,000 PL902 PL903 . . .
103 30000428 SPARK GAP 300V PC 4,000 SG901 SG902 SG904 SG903 .
104 30000459 RES CF 1/4W 100R J PC 2,000 R934 R912 . . .
105 30000466 RES CF 1/4W 1K J PC 1,000 R911 . . . .
106 30000477 RES CF 1/4W 100K J PC 3,000 R905 R906 R909 . .
107 30000492 RES CF 1/4W 120R J PC 1,000 R913 . . . .
108 30000535 RES CF 1/2W 150K J PC 1,000 R904 . . . .
109 30000583 RES CF 1/4W 220R J PC 3,000 R901 R902 R903 . .
110 30000612 RES CF 1/4W 2.4K J PC 1,000 R914 . . . .
111 30000788 RES CF 1/4W 6.8M J PC 1,000 R900 . . . .
112 30000973 RES MF 1/4W 3.9K F PC 1,000 R915 . . . .
113 30001245 RES FUSE 1/4W 0.47R J PC 1,000 R932 . . . .
114 30001284 DIODE 1N4148 0.15A/100V 0.5A PC 2,000 D905 L902-Y . . .
115 30001318 DIODE BA159 1A/800V 20A PC 4,000 D902 D901 D903 D904 .
117 30020603 RES CC 1W 1K K PC 3,000 R907 R908 R910 . .
118 30021483 RES CC 1W 2.2K K PC 1,000 R933 . . . .
119 30021532 SPARK GAP 1500V PC 1,000 SG905 . . . .
120 30021902 PCB 11TP52E PC 1,000 . . . . .
121 30000205 CAP CER 150PF 50V J SL PC 1,000 C919 . . . .
122 30000295 CAP CER 100NF 50V Z F PC 1,000 C917 . . . .
123 30000330 CAP CER 4.7NF 50V K B PC 1,000 C904 . . . .
124 30000352 CAP EL 100UF 16V M PC 1,000 C918 . . . .
125 30001427 TR BF422 PC 1,000 Q900 . . . .
126 30001455 TR BC558B PC 1,000 Q901 . . . .
129 30000075 CAP MKT 100NF 250V K (DC) PC 3,000 C900 C906 C931 . .
130 30000350 CAP EL 10UF 250V M PC 1,000 C905 . . . .
131 30000415 CAP EL 4.7UF 250V M PC 1,000 C902 . . . .
133 30006709 CONN HEADER 5P 2.5MM TOP WHT SD PC 1,000 PL904 . . . .
134 30006841 CAP MKP 1.2NF 1.6KV J PC 1,000 C903 . . . .
135 30012894 CONN HEADER 10P 2.54MM TOP WHT PC 1,000 PL905 . . . .
136 30019071 CABL 1P/550 DIS UL1672AWG22 PC 1,000 PL901 . . . .
137 35000135 TEST PIN 1.1MM PC 1,000 PL902 . . . .
139 20103005 HE.ASY.52-CRT BOARD (AK52) PC 1,000 IC900 . . . .
140 30018768 IC TDA6109 PC 1,000 IC900 . . . .
141 35000131 HEATSINK 11TP18 RGB PC 1,000 . . . . .
142 35000158 NUT C ZN BOTTOM M3 PC 1,000 . . . . .
143 35000165 KNURL WASHER C ZNSY 3*6*04 (M3) PC 1,000 . . . . .
144 35000189 SCREW C NI YSMB M3*6 PC 1,000 . . . . .
145 30001855 SOCKET CRT NARROWNECK W/GND PC 1,000 PL900A . . . .
146 20124465 CHS.ASSY.52B-13923111321211G PC 1,000 . . . . .
149 20094516 CHASSIS FRAME AK37 (I) V.0 PC 1,000 . . . . .
150 20094517 PCB GUIDE RAIL (HIGH BIG) (I) V.0 PC 2,000 . . . . .
151 60000009 FR-HIPS NATR.V-0 KG 0,007 . . . . .
152 60000022 MASTERBATCH (BLACK) G 0,035 . . . . .
153 60000009 FR-HIPS NATR.V-0 KG 0,259 . . . . .
154 35005061 SCREW RB C SK ZN YFMB 2.9*9.5 PC 4,000 . . . . .
157 30001692 FILTER SAW OFWK3953M PC 1,000 Z950 . . . .
158 30009833 CABL 1P/100 SIS PC 1,000 KX22 . . . .
159 30012545 FILTER SAW K9656M PC 1,000 Z951 . . . .
161 30001270 PTC 9 OHM PC 1,000 TH801 . . . .
162 30002183 RELAY MON15 KI-S-212M PC 1,000 RL801 . . . .
164 30009366 DIODE UF5402 3A/200V 150A PC 1,000 D811 . . . .
166 30009637 TUNER WSP (PLL) 38.9 MK2 - BATCH PC 1,000 TU200 . . . .
168 30015053 SOCKET SCART NEW TYPE PC 1,000 PL204 . . . .
170 20000848 FUSE ASSY.TK79-A (2.5A) PC 1,000 F801 . . . .
171 30001731 FUSE 2.5A 250V 5*20MM PC 1,000 . . . . .
172 35000136 FUSE HOLDER TK79-A (GRAY) PC 1,000 . . . . .
174 20070614 HE.ASY.37-SMPS 170-270V PC 1,000 Q802 . . . .
175 30001386 TR MTP6N60E (PLASTIC) PC 1,000 . . . . .
178 35000181 SCREW C ZN YSMB M3*8 PC 1,000 . . . . .
179 35006413 HEATSINK SMPS AK45 PC 1,000 . . . . .
180 70000074 SILICON (GRES) KG 0,010 . . . . .
181 20085393 HE.ASY.33-DIODE UF5407 (33/52) PC 1,000 D805 . . . .
182 30001964 FERRITE BAR 5*8 PC 1,000 . . . . .
183 30007681 DIODE UF5407 3A/800V 150A PC 1,000 . . . . .
184 35004134 HEATSINK DIODE (2) PC 1,000 . . . . .
185 20102765 HE.ASY.52A-SMPS REG2 PC 1,000 . . . . .
186 30001500 IC LM7808 PC 1,000 IC803 . . . .
187 35000142 HEATSINK 15AK14/15 15/TP ORTAK PC 1,000 . . . . .
191 20102766 HE.ASY.52A-VERTICAL PC 1,000 . . . . .
192 30007799 TR BDX53BFI PC 1,000 Q104 . . . .
193 30013687 IC TDA8177F PC 1,000 IC100 . . . .
195 35000166 KNURL WASHER C NI 3.2*6.5*0.6 PC 2,000 . . . . .
197 35005353 HEATSINK VERTICAL AK52 PC 1,000 . . . . .
198 70000074 SILICON (GRES) G 0,010 . . . . .
199 20102767 HE.ASY.52A-HORIZANTAL PC 1,000 . . . . .
200 30007678 DIODE GUC DTV32F1500A 6A/1500V 100A PC 1,000 D104 . . . .
201 30007768 DIODE STTA506F 5A/600V 55A PC 1,000 D105 . . . .
202 30016686 TR 2SC5302 PC 1,000 Q101 . . . .
204 35000166 KNURL WASHER C NI 3.2*6.5*0.6 PC 3,000 . . . . .
207 35005354 HEATSINK HORIZONTAL AK52 PC 1,000 . . . . .
208 20106073 HE.ASY.17PW02-STEPDOWN PC 1,000 Q813 . . . .
209 30007802 TR STP20N06LFP PC 1,000 . . . . .
214 20108354 DIODE BRIDGE GBU4M 4A/1000V 150A(FORMLU) PC 1,000 D810 . . . .
215 30007758 DIODE BRIDGE GBU4M 4A/1000V 150A PC 1,000 . . . . .
216 20108636 HE.ASY.52A-LM1086 3.3 1.5A 15AK14/15 ORT PC 1,000 . . . . .
217 30019617 IC LDO LM1086 3.3V/1.5A TO220 PC 1,000 IC812 . . . .
222 30000094 CAP MKT 220NF 275V M AC PC 1,000 C801 . . . .
223 30000161 CAP MKP 47NF 630V J PC 1,000 C805 . . . .
224 30000350 CAP EL 10UF 250V M PC 1,000 C117 . . . .
225 30000360 CAP EL 1000UF 25V M PC 6,000 C120 C124 C826 C825 C851
. . . . . C842 . . . .
226 30000383 CAP EL 2200UF 25V M PC 4,000 C821 C822 C424 C432 .
227 30000402 CAP EL 47UF 100V M PC 1,000 C119 . . . .
228 30000411 CAP EL 4700UF 16V M PC 1,000 C834 . . . .
229 30000415 CAP EL 4.7UF 250V M PC 1,000 C113 . . . .
230 30000421 CAP EL 220UF 400V M (FOR 28'') PC 1,000 C807 . . . .
231 30000440 CAP CER 2.2NF 4KV M PC 2,000 C810 C850 . . .
233 30001077 RES MO 2W 10R J PC 2,000 R145 R180 . . .
234 30001079 RES MO 1W 100R J PC 1,000 R104 . . . .
235 30001086 RES MO 2W 10K J PC 1,000 R116 . . . .
236 30001168 RES MO 2W 470RJ PC 1,000 R117 . . . .
237 30001174 RES MO 2W 0.47R J PC 2,000 R833 R828 . . .
238 30001224 RES FUSE 1/2W 0.22R J PC 1,000 R844 . . . .
239 30001288 DIODE BYV27-200 2A/200V 50A PC 1,000 D808 . . . .
240 30001299 DIODE UF5404 3A/400V 150A PC 2,000 D108 D109 . . .
241 30001762 CONN HEADER 2P 2.5MM(9.7MM) TOP PC 1,000 PL405 . . . .
242 30001764 CONN HEADER 2P 2.5MM(9.7MM) TOP BLACK PC 1,000 PL406 . . . .
243 30001783 CONN HEADER 5P 2.5MM TOP BD PC 1,000 PL408 . . . .
244 30001792 CONN HEADER 2P 7.5MM TOP WHT PC 2,000 PL103 PL802 . . .
245 30001795 CONN HEADER 3P 5/7.5MM TOP WHT PC 1,000 PL801 . . . .
247 30001960 FERIT BAR 6*20MM AK16 PC 2,000 L419 L420 . . .
248 30002851 XTAL 4MHZ L.C=30PF PC 1,000 X951 . . . .
250 30006743 TRF. HORIZONTAL DRIVER 15AK17-17" PC 1,000 TR100 . . . .
251 30006909 CAP EL 100UF M 250V PC 2,000 C816 C115 . . .
252 30007757 COIL INJECTION EW 6MH AK28 PC 1,000 L101 . . . .
253 30007771 FIXED COIL 100UH PC 1,000 L100 . . . .
254 30009366 DIODE UF5402 3A/200V 150A PC 3,000 D803 D804 D824 . .
255 30009846 CABL 1P/40 SIS PC 2,000 PL418-PL419
PL420-PL421
. . .
257 30010921 DOUBLE-DECK SCART SOCKET PC 1,000 PL203 . . . .
259 30011968 IC SMPS MC44608 DIP8 PC 1,000 IC804 . . . .
260 30015087 IC OPTOCOUPLER TCET1102G PC 1,000 IC801 . . . .
261 30017799 CNAS 5P/500 TUB SIS W/DC UL1007AWG24 PC 1,000 PL101 . . . .
262 30018078 LINE FILTER 2X22MH (AK37) PC 1,000 L805 . . . .
263 30018412 CONN HOUSING 35P 3.0MM TOP DR PC 2,000 PL409 PL410 . . .
264 30018422 IC AAMP TDA7480L 10W PDIP20 PC 2,000 IC401 IC402 . . .
266 30018627 TR NMOS IRFU110 4.3A/100V TO251 PC 1,000 Q100 . . . .
267 30019205 TRF SMPS AK52 (170-270V) 170W PC 1,000 TR801 . . . .
269 30020772 CNAS 10P/320 AK52 SHL W/DC UL1533AWG24 PC 1,000 PL853 . . . .
270 30020805 CABL 1P/150 SIS W/FER PC 1,000 KXX1 . . . .
271 40011350 SPACER SUPPORT SCC-3C-NZW PC 1,000 . . . . .
272 40011922 EDGE SADDLE (CT-16) PC 2,000 . . . . .
273 70000029 SOLDER (INGOT) 63/37 KG 0,020 . . . . .
274 70000661 SILICON V0 (UL 1410)(Firma Catg.No3748 G 5,000 . . . . .
276 30000075 CAP MKT 100NF 250V K (DC) PC 1,000 C861 . . . .
277 30001792 CONN HEADER 2P 7.5MM TOP WHT PC 1,000 PL804 . . . .
278 30018085 CAP VAR 510V K MFCN14D511 PC 1,000 R870 . . . .
285 30001457 TR BC848B SMD PC 1,000 Q950 . . . .
286 30012411 DIODE BA782 SMD PC 1,000 D961 . . . .
287 30012603 CAP SMD 100NF 25V K R (0603) PC 1,000 C958 . . . .
288 30012657 RES SMD 1/16W 1K J (0603) PC 1,000 R963 . . . .
289 30012659 RES SMD 1/16W 2.2K J (0603) PC 1,000 R962 . . . .
290 30012685 RES SMD 1/16W 33K J (0603) PC 1,000 R960 . . . .
291 30012705 RES SMD 1/16W 6.8K J (0603) PC 1,000 R961 . . . .
293 30016126 CAP SMD 220NF 16V K R (0603) PC 1,000 C996 . . . .
294 30021083 IC TDA9886T/V3-SO24 PC 1,000 IC954 . . . .
299 30000466 RES CF 1/4W 1K J PC 1,000 R843 . . . .
300 30000352 CAP EL 100UF 16V M PC 1,000 C840 . . . .
301 30001454 TR BC548B PC 1,000 Q801 . . . .
302 30001285 DIODE 1N4148 SMD PC 1,000 D830 . . . .
303 30001457 TR BC848B SMD PC 1,000 Q808 . . . .
304 30012641 RES SMD 1/16W 10K J (0603) PC 2,000 R808 R842 . . .
305 30012692 RES SMD 1/16W 4.7K J (0603) PC 1,000 R807 . . . .
307 30009699 DIODE ZENER SMD BZT55C12 PC 1,000 D207 . . . .
308 30012581 CAP SMD 1NF 50V K R (0603) PC 2,000 C274 C284 . . .
309 30012589 CAP SMD 4.7NF 50V K (0603) PC 2,000 C276 C287 . . .
310 30012592 CAP SMD 6.8NF 50V K (0603) PC 2,000 C270 C271 . . .
311 30012607 CAP SMD 150PF 50V J (0603) PC 4,000 C273 C280 C289 C290 .
312 30012707 RES SMD 1/16W 680R J (0603) PC 2,000 R230 R235 . . .
313 30013413 FERRITE BEAD ACB2012H-300 PC 4,000 L224 L225 L226 L228 .
314 30018735 DIODE ZENER BZT55C15 15V SMD PC 1,000 D206 . . . .
323 30000918 RES MF 1/4W 2.1K F PC 1,000 R121 . . . .
324 30001036 RES MF 1/4W 95K F PC 1,000 R123 . . . .
325 30001131 RES MO 1W 0.22R J PC 1,000 R103 . . . .
326 30001291 DIODE HER107 1A/800V 30A PC 1,000 D100 . . . .
327 30007783 RES FUSE 1/4W 2.2R J PC 1,000 R122 . . . .
328 30000078 CAP MKT 1UF 100V M PC 1,000 C129 . . . .
329 30000319 CAP CER 2.7NF 500V K B PC 1,000 C808 . . . .
330 30001435 TR NBJT BC639 1A/100V TO92 PC 1,000 Q809 . . . .
331 30012509 RES SMD 1/16W 100K J (0603) PC 1,000 R113 . . . .
332 30012567 CAP SMD 220PF 50V J (0603) PC 1,000 C108 . . . .
341 30000452 RES CF 1/4W 10R J PC 1,000 R806 . . . .
342 30000459 RES CF 1/4W 100R J PC 3,000 R952 R954 R995 . .
343 30000466 RES CF 1/4W 1K J PC 2,000 R118 R832 . . .
344 30000477 RES CF 1/4W 100K J PC 3,000 R829 R136 R157 . .
345 30000481 RES CF 1/4W 1M J PC 1,000 R804 . . . .
346 30000515 RES CF 1/4W 15R J PC 1,000 R429 . . . .
347 30000531 RES CF 1/4W 15K J PC 1,000 R186 . . . .
348 30000541 RES CF 1/4W 1.5M J PC 1,000 R146 . . . .
349 30000564 RES CF 1/4W 18K J PC 1,000 R126 . . . .
350 30000583 RES CF 1/4W 220R J PC 1,000 R105 . . . .
351 30000622 RES CF 1/4W 270R J PC 1,000 R165 . . . .
352 30000628 RES CF 1/4W 2.7K J PC 1,000 R169 . . . .
353 30000660 RES CF 1/4W 3.3K J PC 1,000 R866 . . . .
354 30000718 RES CF 1/4W 4.7K J PC 6,000 R110 R127 R823 R824 R860
. . . . . R802 . . . .
355 30000729 RES CF 1/4W 470K J PC 1,000 R129 . . . .
356 30000744 RES CF 1/4W 560R J PC 1,000 R147 . . . .
357 30000769 RES CF 1/2W 680R J PC 2,000 R820 R821 . . .
358 30000784 RES CF 1/4W 680K J PC 1,000 R155 . . . .
359 30000792 RES CF 1/4W 75R J PC 1,000 R998 . . . .
360 30000918 RES MF 1/4W 2.1K F PC 1,000 R856 . . . .
361 30000925 RES MF 1/4W 2.2K F PC 1,000 R855 . . . .
362 30000983 RES MF 1/4W 4.7K F PC 1,000 R805 . . . .
363 30001011 RES MF 1/4W 6.8K F PC 2,000 R142 R143 . . .
364 30001036 RES MF 1/4W 95K F PC 1,000 R156 . . . .
365 30001159 RES MO 1W 0.33R J PC 1,000 R810 . . . .
366 30001257 RES MG 1/2W 4.7M J PC 1,000 R812 . . . .
367 30001284 DIODE 1N4148 0.15A/100V 0.5A PC 2,000 D826 D404 . . .
368 30001288 DIODE BYV27-200 2A/200V 50A PC 1,000 D111 . . . .
369 30001291 DIODE HER107 1A/800V 30A PC 3,000 D106 D107 D110 . .
370 30001318 DIODE BA159 1A/800V 20A PC 7,000 D120 D801 D814 D815 D829
. . . . . D818 D123 . . .
371 30001323 DIODE BY299 2A/800V 70A PC 1,000 D802 . . . .
372 30001329 DIODE 1N4007 1A/1000V 30A PC 2,000 D812 D831 . . .
373 30001344 DIODE ZENER 6.2V 1/2W PC 1,000 D806 . . . .
374 30001377 DIODE ZENER 33V UZT 33B PC 1,000 D113 . . . .
375 30001979 FIXED COIL 1UH Q45 M-A PC 1,000 L951 . . . .
376 30001992 FIXED COIL 10UH Q65 K-A PC 1,000 L803 . . . .
377 30001996 FIXED COIL 22UH Q40 K PC 1,000 L109 . . . .
378 30006691 DIODE ZENER 3.3V PC 1,000 D813 . . . .
379 30006712 FERRITE BEAD 3.5X4.7X0.8 PC 5,000 L105 L106 L417 L418 J130
380 30009036 RES FUSE 1/2W 0.1R J PC 1,000 R125 . . . .
381 30025350 PCB 11AK52B6 PC 1,000 . . . . .
382 30000069 CAP MKT 1NF 100V J PC 4,000 C469 C470 C472 C473 .
383 30000071 CAP MKT 10NF 63V J PC 2,000 C405 C466 . . .
384 30000074 CAP MKT 100NF 63V J PC 1,000 C142 . . . .
385 30000099 CAP MKT 33NF 63V J PC 1,000 C812 . . . .
387 30000109 CAP MKT 470NF 63V J PC 2,000 C963 C966 . . .
388 30000190 CAP CER 100PF 50V J CH PC 1,000 C864 . . . .
389 30000283 CAP CER 1NF 50V K B PC 1,000 C131 . . . .
390 30000286 CAP CER 1NF 500V K B PC 1,000 C145 . . . .
391 30000295 CAP CER 100NF 50V Z F PC 6,000 C831 C430 C824 C410 C409
. . . . . C429 . . . .
392 30000296 CAP CER 100NF 100V Z F PC 3,000 C146 C128 C148 . .
393 30000302 CAP CER 1.8NF 50V KB PC 2,000 C123 C130 . . .
395 30000346 CAP EL 10UF 100V M PC 1,000 C107 . . . .
396 30000352 CAP EL 100UF 16V M PC 2,000 C856 C468 . . .
398 30000362 CAP EL 1UF 50V M PC 1,000 C106 . . . .
399 30000367 CAP EL 1UF 250V M PC 2,000 C837 C862 . . .
400 30000375 CAP EL 220UF 16V M PC 1,000 C857 . . . .
401 30000387 CAP EL 33UF 50V M PC 1,000 C804 . . . .
402 30000393 CAP EL 3.3UF 50V M PC 2,000 C845 C134 . . .
403 30000400 CAP EL 47UF 50V M PC 3,000 C139 C828 C956 . .
404 30000431 CAP CER 100PF 1KV M PC 1,000 C116 . . . .
405 30000433 CAP CER 1NF 1KV M B PC 3,000 C843 C471 C474 . .
406 30001384 TR MCR22-6 PC 1,000 Q817 . . . .
407 30001428 TR BF423 PC 1,000 Q806 . . . .
408 30001454 TR BC548B PC 4,000 Q105 Q803 Q805 Q810 .
409 30001455 TR BC558B PC 1,000 Q814 . . . .
410 30001506 IC TL431 PC 3,000 Q116 Q815 Q816 . .
411 30007308 CAP CER 220PF 1KV K (PULSE) PC 4,000 C806 C813 C814 C815 .
412 30009208 CAP CER 470PF 1KV K (PULSE) PC 1,000 C809 . . . .
413 30019641 CAP MKT 100NF 100V J NO-HIT PC 1,000 C135 . . . .
414 30000284 CAP SMD 1NF 50V K R (0805) PC 1,000 C301 . . . .
415 30000294 CAP SMD 100NF 50V K (0805) PC 10,000 C100 C125 C126 C803 C823
. . . . . C827 C846 C859 C817 C818
416 30000309 CAP SMD 2.2NF 50V K R 0805 PC 1,000 C811 . . . .
417 30000469 RES SMD 1/10W 1K J 0805 PC 2,000 R827 R834 . . .
418 30000475 RES SMD 1/10W 10K J 0805 PC 4,000 R148 R161 R830 R835 .
419 30000503 RES SMD 1/10W 12K J (0805) PC 1,000 R837 . . . .
420 30000517 RES SMD 1/10W 15R J 0805 PC 1,000 R838 . . . .
421 30000529 RES SMD 1/10W 1.5K J PC 2,000 R102 R166 . . .
422 30000593 RES SMD 1/10W 2.2K J (0805) PC 3,000 R803 R836 R108 . .
423 30000614 RES SMD 1/10W 2.4K J (0805) PC 1,000 R814 . . . .
424 30000626 RES SMD 1/10W 270R J PC 1,000 R171 . . . .
425 30000631 RES SMD 1/10W 2.7K J 0805 PC 1,000 R131 . . . .
426 30000636 RES SMD 1/10W 27K J 0805 PC 1,000 R138 . . . .
427 30000710 RES SMD 1/10W 47R J (0805) PC 1,000 R813 . . . .
428 30000721 RES SMD 1/10W 4.7K J PC 3,000 R159 R162 R160 . .
429 30000782 RES SMD 1/10W 68K J PC 2,000 R818 R868 . . .
430 30001285 DIODE 1N4148 SMD PC 15,000 D114 D117 D118 D119 D807
. . . . . D809 D820 D821 D819 D823
. . . . . D127 D128 D951 D962 D963
431 30001457 TR BC848B SMD PC 9,000 Q112 Q113 Q114 Q200 Q804
. . . . . Q807 Q108 Q811 Q952 .
. . . . . Q400 Q117 . . .
435 30001971 FERRITE BEAT (805) BLM21A601S PC 1,000 L802 . . . .
436 30007026 RES SMD 1/10W 5.1K J(0805) PC 1,000 R831 . . . .
438 30007763 DIODE ZENER SMD BZT55C5V1 PC 4,000 D103 D112 D201 D827 .
439 30007789 RES SMD 1/10W 27K F (0805) PC 1,000 R137 . . . .
440 30009699 DIODE ZENER SMD BZT55C12 PC 4,000 D822 D202 D203 D124 .
441 30010560 CAP SMD 220NF 25V K R (0805) PC 1,000 R163 . . . .
442 30010643 RES SMD 1/10W 39R J (0805) PC 1,000 R970 . . . .
443 30012506 RES SMD 1/16W 1.5K J (0603) PC 1,000 R187 . . . .
444 30012508 RES SMD 1/16W 1.8K J (0603) PC 1,000 R406 . . . .
445 30012510 RES SMD 1/16W 100R J (0603) PC 4,000 R815 R953 R955 R964 .
446 30012560 CAP SMD 100PF 50V J (0603) PC 2,000 C467 C950 . . .
447 30012566 CAP SMD 22PF 50V J (0603) PC 1,000 C965 . . . .
448 30012567 CAP SMD 220PF 50V J (0603) PC 1,000 C852 . . . .
449 30012568 CAP SMD 270PF 50V J (0603) PC 2,000 C406 C426 . . .
451 30012572 CAP SMD 390PF 50V J (0603) PC 1,000 C962 . . . .
452 30012574 CAP SMD 470PF 50V J (0603) PC 1,000 C867 . . . .
453 30012581 CAP SMD 1NF 50V K R (0603) PC 7,000 C240 C249 C839 C140 C994
. . . . . C1006 C1007 . . .
455 30012583 CAP SMD 1.5NF 50V K (0603) PC 1,000 C968 . . . .
456 30012585 CAP SMD 2.2NF 50V K R (0603) PC 2,000 C407 C427 . . .
457 30012589 CAP SMD 4.7NF 50V K (0603) PC 8,000 C243 C244 C245 C247 C250
. . . . . C251 C419 C433 . .
458 30012590 CAP SMD 47NF 50V K (0603) PC 1,000 C105 . . . .
459 30012592 CAP SMD 6.8NF 50V K (0603) PC 1,000 C237 . . . .
460 30012592 CAP SMD 6.8NF 50V K (0603) PC 3,000 C233 C235 C236 . .
. . . . . C421 C853 C951 C972 .
462 30012607 CAP SMD 150PF 50V J (0603) PC 16,000 C239 C241 C246 C248 C252
. . . . . C253 C256 C261 C262 C263
. . . . . C266 C267 C307 C308 C309
. . . . . C310 . . . .
463 30012610 CAP SMD 10NF 50V J (0603) PC 1,000 C964 . . . .
464 30012641 RES SMD 1/16W 10K J (0603) PC 11,000 R119 R822 R825 R839 R840
. . . . . R849 R158 R853 R861 R862
. . . . . R819 . . . .
465 30012644 RES SMD 1/16W 12K J (0603) PC 1,000 R966 . . . .
. . . . . R863 S802 . . .
467 30012659 RES SMD 1/16W 2.2K J (0603) PC 10,000 R107 R109 R112 R115 R847
. . . . . R848 R851 R852 R850 R951
468 30012662 RES SMD 1/16W 2.7K J (0603) PC 1,000 R111 . . . .
469 30012668 RES SMD 1/16W 220R J (0603) PC 1,000 R994 . . . .
470 30012669 RES SMD 1/16W 22K J (0603) PC 2,000 R972 R973 . . .
471 30012677 RES SMD 1/16W 3.3K J (0603) PC 1,000 R422 . . . .
472 30012682 RES SMD 1/16W 30K J (0603) PC 1,000 R403 . . . .
473 30012684 RES SMD 1/16W 330R J (0603) PC 1,000 R968 . . . .
474 30012689 RES SMD 1/16W 39K J (0603) PC 1,000 R867 . . . .
475 30012692 RES SMD 1/16W 4.7K J (0603) PC 2,000 R106 R185 . . .
476 30012695 RES SMD 1/16W 470R J (0603) PC 3,000 R845 R864 R993 . .
477 30012696 RES SMD 1/16W 47K J (0603) PC 2,000 R120 R967 . . .
478 30012698 RES SMD 1/16W 5.6K J (0603) PC 1,000 R418 . . . .
479 30012698 RES SMD 1/16W 5.6K J (0603) PC 1,000 R958 . . . .
480 30012705 RES SMD 1/16W 6.8K J (0603) PC 2,000 R922 R965 . . .
482 30012712 RES SMD 1/16W 8.2K J (0603) PC 3,000 R132 R409 R417 . .
483 30012714 RES SMD 1/16W 820R J (0603) PC 1,000 R1006 . . . .
484 30012982 RES SMD 1/16W 10R J 0603 PC 2,000 S408 S409 . . .
486 30013413 FERRITE BEAD ACB2012H-300 PC 8,000 L213 L214 L215 L216 L217
. . . . . L218 L219 L220 . .
487 30013413 FERRITE BEAD ACB2012H-300 PC 1,000 L999 . . . .
488 30014022 RES SMD 1/16W 47R J (0603) PC 2,000 R205 R997 . . .
489 30014420 RES SMD 1/16W 10K F (0603) PC 1,000 R415 . . . .
490 30016126 CAP SMD 220NF 16V K R (0603) PC 1,000 C967 . . . .
491 30016654 CAP SMD 100NF 16V K R (0603) PC 3,000 C848 C212 C858 . .
492 30018735 DIODE ZENER BZT55C15 15V SMD PC 2,000 D204 D205 . . .
493 20124423 MD.ASY.FB52A-311112111321211 PC 1,000 . . . . .
495 20101701 MD.SMD.FB52A-FAV IN PC 1,000 . . . . .
497 30000074 CAP MKT 100NF 63V J PC 1,000 C882 . . . .
498 30000315 CAP SMD 220NF 25V Z (0805) PC 2,000 C408 C409 . . .
499 30001971 FERRITE BEAT (805) BLM21A601S PC 1,000 L850 . . . .
501 30012589 CAP SMD 4.7NF 50V K (0603) PC 2,000 C473 C474 . . .
502 30012657 RES SMD 1/16W 1K J (0603) PC 2,000 R437 R438 . . .
503 30012713 RES SMD 1/16W 75R J (0603) PC 1,000 R891 . . . .
504 30017143 COIL SMD 22UH (2520) PC 2,000 L407 L408 . . .
505 20101763 MD.SMD.FB52A-HEADPHONE PC 1,000 . . . . .
507 30000345 CAP EL 10UF 50V M PC 1,000 C481 . . . .
508 30000352 CAP EL 100UF 16V M PC 2,000 C430 C432 . . .
509 30000362 CAP EL 1UF 50V M PC 1,000 C433 . . . .
510 30000315 CAP SMD 220NF 25V Z (0805) PC 2,000 C426 C427 . . .
511 30001285 DIODE 1N4148 SMD PC 2,000 D404 D405 . . .
512 30001971 FERRITE BEAT (805) BLM21A601S PC 2,000 L400 L401 . . .
513 30010024 IC TDA1308T SOIC 8P PC 1,000 IC401 . . . .
514 30012567 CAP SMD 220PF 50V J (0603) PC 2,000 C477 C478 . . .
516 30012589 CAP SMD 4.7NF 50V K (0603) PC 4,000 C443 C444 C429 C434 .
517 30012592 CAP SMD 6.8NF 50V K (0603) PC 2,000 C401 C403 . . .
518 30012641 RES SMD 1/16W 10K J (0603) PC 2,000 R412 R416 . . .
519 30012692 RES SMD 1/16W 4.7K J (0603) PC 2,000 R411 R413 . . .
520 30012700 RES SMD 1/16W 51K J (0603) PC 2,000 R414 R415 . . .
522 30016654 CAP SMD 100NF 16V K R (0603) PC 1,000 C428 . . . .
523 30017143 COIL SMD 22UH (2520) PC 2,000 L409 L410 . . .
524 20101768 MD.SMD.FB52A-WO/PIP PC 1,000 . . . . .
526 20101771 MD.SMD.FB52A-VIRTUAL DOLBY&3D PANORAMA PC 1,000 . . . . .
527 30018653 IC MSP3411G PLQFP64 PC 1,000 IC400 . . . .
528 20105455 MD.SMD.FB52A-WO/DVD PC 1,000 . . . . .
530 20126358 MD.SMD.FB52A3-COMMON(TOSHIBA) PC 1,000 . . . . .
533 30023510 PCB 11FB52A4 PC 1,000 . . . . .
534 30000068 CAP MKT 1NF 63V K PC 1,000 C604 . . . .
536 30000109 CAP MKT 470NF 63V J PC 3,000 C642 C643 C688 . .
. . . . . C645 C659 C660 C665 C689
. . . . . C690 C748 C413 C414 C448
. . . . . C450 C697 . . .
538 30000352 CAP EL 100UF 16V M PC 4,000 C722 C723 C873 C402 .
539 30000362 CAP EL 1UF 50V M PC 1,000 C731 . . . .
540 30000362 CAP EL 1UF 50V M PC 2,000 C735 C755 . . .
. . . . . C437 C439 C436 C438 C479
. . . . . C480 . . . .
542 30000393 CAP EL 3.3UF 50V M PC 2,000 C663 C412 . . .
543 30000396 CAP EL 47UF 16V M PC 1,000 C754 . . . .
544 30000413 CAP EL 4.7UF 50V M PC 1,000 C753 . . . .
545 30000444 CAP CER 470PF 1KV KB PC 1,000 C472 . . . .
546 30000315 CAP SMD 220NF 25V Z (0805) PC 15,000 C406 C407 C451 C452 C680
. . . . . C683 C694 C907 C908 C909
. . . . . C453 C454 C888 C890 C892
547 30001285 DIODE 1N4148 SMD PC 8,000 D401 D402 D403 D600 D601
. . . . . D602 D604 D750 . .
. . . . . Q603 Q605 Q606 Q610 Q612
. . . . . Q613 Q614 Q721 Q722 Q723
. . . . . Q724 Q725 Q726 Q727 Q729
. . . . . Q730 Q850 Q856 Q859 Q861
. . . . . Q863 Q731 Q732 Q733 Q403
. . . . . Q404 Q852 Q720 Q750 Q751
. . . . . Q752 . . . .
. . . . . Q728 Q734 . . .
550 30001971 FERRITE BEAT (805) BLM21A601S PC 5,000 L406 L411 L418 L602 L861
551 30003720 DIODE ZENER BZT55C5V6 5.6V SMD PC 1,000 D720 . . . .
552 30007668 IC SDA9400 PC 1,000 IC600 . . . .
553 30007739 IC LM317T D2PAK PC 1,000 IC602 . . . .
555 30007761 DIODE ZENER SMD BZT55C3V6 PC 1,000 D400 . . . .
556 30010349 IC DDP3310 PC 1,000 IC601 . . . .
557 30012506 RES SMD 1/16W 1.5K J (0603) PC 1,000 R696 . . . .
558 30012509 RES SMD 1/16W 100K J (0603) PC 3,000 R913 R914 R786 . .
559 30012510 RES SMD 1/16W 100R J (0603) PC 26,000 R402 R403 R405 R406 R421
. . . . . R422 R601 R629 R635 R641
. . . . . R689 R690 R691 R692 R693
. . . . . R694 R760 R762 R777 R778
. . . . . R889 R890 R949 R829 R787
. . . . . R835 . . . .
560 30012559 CAP SMD 10PF 50V D COG (0603) PC 2,000 C668 C906 . . .
561 30012565 CAP SMD 1.8PF 50V J CH (0603) PC 2,000 C417 C418 . . .
. . . . . C650 C655 C656 C746 .
. . . . . C404 . . . .
. . . . . C889 C891 . . .
566 30012573 CAP SMD 47PF 50V J (0603) PC 1,000 C700 . . . .
567 30012574 CAP SMD 470PF 50V J (0603) PC 1,000 C699 . . . .
568 30012576 CAP SMD 56PF 50V J CH (0603) PC 2,000 C410 C422 . . .
. . . . . C651 C654 C657 . .
. . . . . C447 C457 C458 C465 C466
. . . . . C471 C623 C455 C456 .
. . . . . C634 C635 C666 . .
572 30012583 CAP SMD 1.5NF 50V K (0603) PC 5,000 C662 C676 C684 C685 C686
573 30012585 CAP SMD 2.2NF 50V K R (0603) PC 8,000 C614 C617 C622 C636 C647
. . . . . C652 C653 C658 . .
574 30012589 CAP SMD 4.7NF 50V K (0603) PC 2,000 C461 C462 . . .
575 30012590 CAP SMD 47NF 50V K (0603) PC 4,000 C661 C677 C681 C691 .
576 30012608 CAP SMD 27PF 50V J CH (0603) PC 2,000 C618 C619 . . .
577 30012609 CAP SMD 68NF 50V K (0603) PC 3,000 C675 C687 C695 . .
578 30012613 CAP SMD 3.3PF 50V C CH(0603) PC 2,000 C601 C602 . . .
. . . . . R655 R659 R761 R763 R779
. . . . . R780 R801 R896 R901 R909
. . . . . R929 R683 R917 R816 R822
. . . . . R825 R826 R899 R623 R781
. . . . . R782 R788 R802 R836 R837
. . . . . R830 . . . .
. . . . . R434 R439 R606 R634 R640
. . . . . R646 R661 R720 R771 R772
. . . . . R789 R790 R791 R792 R793
. . . . . R797 R807 R919 R920 R626
. . . . . R658 R818 R409 R410 R435
. . . . . R436 . . . .
582 30012659 RES SMD 1/16W 2.2K J (0603) PC 4,000 R651 R764 R765 R840 .
583 30012661 RES SMD 1/16W 2.4K J (0603) PC 1,000 R650 . . . .
585 30012669 RES SMD 1/16W 22K J (0603) PC 4,000 R625 R721 R918 R647 .
586 30012673 RES SMD 1/16W 270R J (0603) PC 1,000 R648 . . . .
587 30012675 RES SMD 1/16W 2K J (0603) PC 1,000 R708 . . . .
588 30012677 RES SMD 1/16W 3.3K J (0603) PC 2,000 R752 R753 . . .
589 30012679 RES SMD 1/16W 3.9K J (0603) PC 3,000 R756 R757 R820 . .
591 30012692 RES SMD 1/16W 4.7K J (0603) PC 26,000 R404 R417 R418 R419 R420
. . . . . R754 R755 R785 R798 R897
. . . . . R903 R910 R930 R653 R817
. . . . . R821 R831 R832 R833 R834
. . . . . R902 R663 R823 R824 R838
. . . . . R842 . . . .
. . . . . R766 R767 . . .
. . . . . R828 . . . .
. . . . . R644 R688 R699 R860 R885
. . . . . R886 R904 R906 R911 R931
. . . . . R942 R943 R944 R945 R946
. . . . . R947 R948 R932 R933 R934
. . . . . R935 R936 R937 R905 R951
595 30012719 RES SMD 1/16W 910R J (0603) PC 1,000 R697 . . . .
596 30012982 RES SMD 1/16W 10R J 0603 PC 12,000 R603 R631 R637 R643 R662
. . . . . R892 R907 R921 R927 R894
. . . . . R649 R893 . . .
598 30013001 RES SMD 1/16W 1K F (0603) PC 1,000 R841 . . . .
599 30013571 IC SDA5550 PC 1,000 IC722 . . . .
600 30013686 IC VIDEO SWITCH TEA6415CDT SMD PC 1,000 IC851 . . . .
601 30014022 RES SMD 1/16W 47R J (0603) PC 2,000 R794 R796 . . .
602 30014128 RES SMD 1/16W 33R J (0603) PC 2,000 R604 R938 . . .
603 30015059 IC VPC3230D PC 1,000 IC603 . . . .
604 30016126 CAP SMD 220NF 16V K R (0603) PC 1,000 C842 . . . .
. . . . . C607 C608 C609 C610 C611
. . . . . C625 C626 C632 C664 C672
. . . . . C673 C678 C692 C720 C724
. . . . . C727 C728 C730 C732 C733
. . . . . C734 C739 C740 C741 C742
. . . . . C744 C745 C750 C883 C885
. . . . . C886 C893 C895 C897 C898
. . . . . C752 C400 C884 . .
606 30017143 COIL SMD 22UH (2520) PC 14,000 L402 L403 L404 L405 L412
. . . . . L413 L416 L417 L600 L720
. . . . . L724 L862 L414 L415 .
607 30018093 COIL SMD 3.3uH (2520) PC 13,000 L726 L857 L858 L859 L854
. . . . . L855 L856 L851 L852 L853
. . . . . L723 L721 L722 . .
608 30018409 RES SNETWORK 1/16W 330R J (0603) PC 15,000 R700 R701 R702 R703 R704
. . . . . R705 R706 R707 R808 R809
. . . . . R810 R811 R812 R813 R814
609 30020535 DIODE ZENER SMD BZT55C3V9 PC 1,000 D751 . . . .
610 20128394 MD.SMD.FB52A3-FASTEXT PC 1,000 . . . . .
611 30012580 CAP SMD 820PF 50V J (0603) PC 1,000 C749 . . . .
614 30001833 CONN HEADER 2P 2.5MM SIDE BLUE SD PC 1,000 PL855 . . . .
615 30001844 CONN HEADER 3P 2.5MM SIDE GREEN SD PC 1,000 PL400 . . . .
617 30001756 XTAL 18.432MHZ PC 1,000 X400 . . . .
618 30001834 CONN HEADER 2P 2.5MM SIDE RED SD PC 1,000 PL722 . . . .
619 30001853 SOCKET IC 32P PC 1,000 IC721 . . . .
620 30006662 XTAL 6MHZ PC 1,000 X720 . . . .
621 30006712 FERRITE BEAD 3.5X4.7X0.8 PC 1,000 L601 . . . .
622 30007745 CONN HEADER 10P 2.54MM SIDE WHT DR PC 1,000 PL853 . . . .
623 30008778 XTAL 20.25MHZ PC 1,000 X600 . . . .
624 30008782 XTAL 5MHZ PC 1,000 X601 . . . .
625 30009784 SOCKET IC 8P (DIP) PC 1,000 IC720 . . . .
626 30018115 CONN HEADER 3P 2.5MM SIDE BD SR PC 1,000 PL723 . . . .
627 30018117 CONN HEADER 6P 2.5MM SIDE BD PC 1,000 PL721 . . . .
628 30018410 CONN HEADER 35P 3.0MM SIDE DR PC 2,000 PL857 PL858 . . .
630 30001841 CONN HEADER 3P 2.5MM SIDE BLACK SD PC 1,000 PL401 . . . .
632 20131458 PR.IC.52-AK52B-FASTEXT TOSHIBA T022 PC 1,000 . . . . .
633 30018652 IC SST37VF040 4MBIT 3.3V PDIP-32 PC 1,000 IC721 . . . .
634 30009846 CABL 1P/40 SIS PC 1,000 KX20 . . . .
635 20124498 IC 24C32 A059311112111221211 PC 1,000 . . . . .
636 30015382 IC 24C32 3V PC 1,000 . . . . .
637 20130616 CRT DIFF.KIT AK52B-28" 4:3 VCL 135V(TOSH PC 1,000 . . . . .
638 30000094 CAP MKT 220NF 275V M AC PC 1,000 C802 . . . .
639 30000121 CAP KP 27NF 630V J PC 1,000 C111 . . . .
640 30000167 CAP MKP 560NF 250V J PC 1,000 C112 . . . .
641 30000177 CAP MKP 820NF 250V J PC 1,000 C114 . . . .
642 30000179 CAP MKP 9.1NF 1600V %3.5 PC 1,000 C110 . . . .
643 30001110 RES MO 1W 1.5R J PC 1,000 R139 . . . .
644 30001124 RES MO 3W 220R J PC 1,000 R140 . . . .
645 30001174 RES MO 2W 0.47R J PC 1,000 R141 . . . .
646 30001217 RES FUSE 2W 1.2R J PC 1,000 R128 . . . .
647 30001244 RES FUSE 1/2W 0.47R J PC 1,000 R124 . . . .
648 30001246 RES FUSE 1W 0.47R J PC 1,000 R130 . . . .
650 30007756 COIL BRIDGE 150UH 32KHZ AK28 PC 1,000 L104 . . . .
651 30010517 CAP MKT 33NF 100V K PC 1,000 C102 . . . .
652 30014943 CAP MKP 3.9NF 1600V J PC 1,000 C109 . . . .
653 30017521 TRF FBT SINGLE COMMON FOCUS LAYER (AK41) PC 1,000 TR101 . . . .
654 30018304 LINEARTY COIL 7UH PC 1,000 L103 . . . .
655 30018581 RES MO 2W 150R J PC 1,000 R101 . . . .
656 20124508 SCR.AS.2841 W/SB (AK52)(V0)(GRAY) PC 1,000 . . . . .
657 20123717 BACK DOOR AK45/52 EKO.GRAY (I) V.0 PC 1,000 . . . . .
658 60000009 FR-HIPS NATR.V-0 KG 0,058 . . . . .
660 35000211 SCREW S C ZNSY YSMB 2.9*9.5 PC 4,000 . . . . .
661 35000212 SCREW S C ZNSY YSMB 2.9*13 PC 2,000 . . . . .
662 35000224 SCREW C SK ZN YFMB 2.9*9.5 PC 16,000 . . . . .
663 35000231 SCREW SK C NI YFMB 2.9*6.5 PC 5,000 . . . . .
664 35004572 SCREW P C AgSYF YSB 4x20 PC 10,000 . . . . .
665 35006331 SCREW P C ZN AKBR 7*26 PC 4,000 . . . . .
666 40000082 FOOT RUBBER 8410/11 PC 2,000 . . . . .
667 20124820 MD.ASY.SB103-FAV+HP+SVHS XX41/W (AK52) PC 1,000 . . . . .
670 30001830 CONN HEADER 2P 2.5MM TOP BLUE SD PC 1,000 PL106 . . . .
671 30001839 CONN HEADER 3P 2.5MM TOP GREEN SD PC 1,000 PL107 . . . .
672 30001891 RCA JACK 1P WHITE 28 FAV PC 1,000 JK102 . . . .
673 30001892 RCA JACK 1P RED 28 FAV PC 1,000 JK103 . . . .
674 30001893 RCA JACK 1P YELLOW 28 FAV PC 1,000 JK101 . . . .
676 30001838 CONN HEADER 3P 2.5MM TOP YELLOW SD PC 1,000 PL105 . . . .
677 30001895 JACK 4P DIN TYPE FOR SVHS PC 1,000 JK105 . . . .
679 30001902 JACK HEADPHONE STEREO WO/SW PC 1,000 JK108 . . . .
680 30020932 CNAS 3P/550 FLT W/BLK C+FER UL2468AWG24 PC 1,000 PL108 . . . .
682 30020137 CNAS 600 FAV SVHS W/DC+FER PC 1,000 PL106 . . . .
689 30000594 RES CF 1/4W 22K J PC 2,000 R102 R104 . . .
690 30000712 RES CF 1/4W 470R J PC 2,000 R103 R106 . . .
692 30019363 PCB 11SB103-2 PC 1,000 . . . . .
693 30000190 CAP CER 100PF 50V J CH PC 3,000 C101 C103 C104 . .
699 30000650 RES CF 1/4W 33R J PC 2,000 R110 R111 . . .
701 30000190 CAP CER 100PF 50V J CH PC 1,000 C102 . . . .
705 30000115 CAP MKT 6.8NF 100V J PC 2,000 C105 C106 . . .
707 30006712 FERRITE BEAD 3.5X4.7X0.8 PC 1,000 FXX1 . . . .
708 20128262 LBL.CART.BOX TOSHIBA 28H37G(ÇÝFT KATLI) PC 1,000 . . . . .
709 50023532 LABEL LOT TOSHIBA ÇÝFT KATLI PC 1,050 . . . . .
710 70000621 RIBBON 80MM*450MM PC 1,050 . . . . .
711 20128263 LBL.BCK.CVR.TOSHIBA TOSHIBA 28H37G "52" PC 1,000 . . . . .
712 20013018 LBL.BCK.CVR.ASSY (TV) (WO/UL) PC 1,000 . . . . .
713 50023173 LABEL LOT W/BARCODE (77X256) PC 1,050 . . . . .
714 70000621 RIBBON 80MM*450MM PC 1,030 . . . . .
715 20128265 ARTWORK TOSH.TOSHIBA 28H37G(AK52) PC 1,000 . . . . .
716 20100980 R/C 2143 TOSHIBA CT-841(SILVER/P)(GRAY/S PC 1,000 . . . . .
717 20096229 R/C 2143 NOBRAND SILVER (F) PC 1,000 . . . . .
718 20094768 R/C KIT 2143 TOSHIBA PC 1,000 . . . . .
719 20094767 MD.ASY.UK05 PC 1,000 . . . . .
720 20094766 UKV.B.ASSY.UK05 (SMD) PC 1,000 . . . . .
721 30000489 RES SMD 1/10W 1R J (0805) PC 1,000 R102 . . . .
722 30012509 RES SMD 1/16W 100K J (0603) PC 1,000 R103 . . . .
723 30012510 RES SMD 1/16W 100R J (0603) PC 1,000 R100 . . . .
724 30012578 CAP SMD 68PF 50V J (0603) PC 2,000 C101 C102 . . .
726 30018063 IC HT48RA0A OTP PC 1,000 IC101 . . . .
727 30018712 PCB 11UK05-2 PC 1,000 . . . . .
728 30000352 CAP EL 100UF 16V M PC 1,000 C100 . . . .
729 30001453 TR BC337 PC 1,000 Q100 . . . .
730 30002733 LED INFRARED IR333 PC 1,000 D100 . . . .
731 30002852 XTAL REZ 455KHZ PC 1,000 X100 . . . .
732 35002401 BATTERY CONT.SINGLE (-) RC2040 PC 1,000 . . . . .
733 35005008 BATTERY CONT.SINGLE (+) RC2040 TOSHIBA PC 1,000 . . . . .
734 35000228 SCREW SK C ZNSY YSMB 2.9*9.5 PC 1,000 . . . . .
735 35005007 DOUBLE BATTERY CONTACT UKV-900 TOSHIBA PC 1,000 . . . . .
736 40005467 LENS RC2040(I) PC 1,000 . . . . .
737 40010082 RUBBER PAD TRP41 (RC 2143) TOSHIBA PC 1,000 . . . . .
738 40012344 SPONGE (BATTERY DOOR) (15x31x5mm) PC 1,000 . . . . .
739 40005299 BATTERY COVER RC2040 SILVER(P) PC 1,000 . . . . .
740 40009346 BOTTOM CVR R/C 21/2240 SILVER(P) PC 1,000 . . . . .
741 40010357 TOP CVR R/C 2143 NOBRAND (S) SILVER(P) PC 1,000 . . . . .
742 30002391 BATTERY AAA UM4 1.5V GREEN PC 2,000 . . . . .
743 50039214 I/B TOSHIBA 28H37G P/92195/2143/GESIPFD PC 1,000 . . . . .
744 30002754 28" CPT TUBE 100 HZ FLAT IRON PC 1,000 . . . . .
745 40012621 LOGO TOSHIBA (W/P-SILVER BR/H.ST)(GRAY) PC 1,000 . . . . .
746 50000007 PLASTIZOTE (1400*1000) PC 1,000 . . . . .
747 50031267 LABEL EHT/27.8KV BEAM/1050uA (GER) PC 1,000 . . . . .
Cabinet Exploded View
N/A
TOSHIBA Information Systems (UK) Ltd
Consumer Products Division, European Service Centre, Admiralty Way, Camberley, Surrey. GU15 3DT

Tevion 11ak52 SM

Uploaded by

Copyright:

Available Formats

Tevion 11ak52 SM

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tevion 11ak52 SM

Uploaded by

Copyright:

Available Formats

050-200320A

PRINTED IN UK. 2002 C

General description of UV1316:

3.IF PART (DRX 3960A)

5.MULTI STANDARD SOUND PROCESSOR

6.SOUND OUTPUT STAGE WITH TDA7480L

7.VERTICAL OUTPUT STAGE WITH TDA8177F

8.VIDEO OUTPUT AMPLIFIER TDA6109

11.SERIAL ACCESS 32K EEPROM

12.CLASS AB STEREO HEADPHONE DRIVER TDA1308

SYMBOL PIN DESCRIPTION

DIP connections LCC Connections TSOP Connections

SDA Serial Address/Data Input/Output

SCL Serial Clock

14.4.2.Pin Definition and functions

Pin No. P-LCC-68-1 Symbol Function

Pin No. Name Type Description

14.8.3.Pin connection and short descriptions

External Crystal and Programmable clock speed

14.11.2.Pin Connections and Short Descriptions

Pin No. Pin Name Type Connection Short Description

SYMBOL PIN DESCRIPTION

14.15.3.Pin connection and short descriptions

Pin no Pin name Type Supply Connection Short description

14.20.4.Pin Function description

Pin Name Description

Number Name Function

Pin Mnemonic Function

15.AK52 CHASSIS MANUAL ADJUSTMENTS PROCEDURE

15.2.SYSTEM VOLTAGE ADJUSTMENTS

SYSTEM VOLTAGE TYPE OF CRT

15.6.IF ADJUSTMENT FOR L’ MODE

H/V VIDEO ADJUSTMENTS OPTIONS

First page Second Page

16.2.H/V (HORIZONTAL AND VERTICAL GEOMETRY ALIGNMENTS)

WdR, WdG, WdB: WHITE BALANCE ADJUSTMENT

CuR, CuG, CuB

MAIN TUNER DRX 3960

U/V DRIVE -Vert.Sup

Back_V Back_A Front_V Front_A C SC2_R(Scart2_C)

S1 S2 MONO IN QSS Surround

General description of UV1316:

3.IF PART (TDA9885/86)

5.MULTI STANDARD SOUND PROCESSOR

6.SOUND OUTPUT STAGE WITH TDA7480L

7.VERTICAL OUTPUT STAGE WITH TDA8177F

9.POWER SUPPLY (SMPS)

11.SERIAL ACCESS 32K EEPROM

12.CLASS AB STEREO HEADPHONE DRIVER TDA1308

SYMBOL PIN DESCRIPTION

DIP connections LCC Connections TSOP Connections

SDA Serial Address/Data Input/Output

SCL Serial Clock

14.4.2.Pin Definition and functions

Pin No. P-LCC-68-1 Symbol Function

Pin No. Name Type Description

14.8.3.Pin connection and short descriptions

External Crystal and Programmable clock speed