Safety Data Sheet

SECTION 1 IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE

COMPANY/UNDERTAKING

1.1 Product identifier

High Temp Premium 2
Product Number(s): 002401, 802401

1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified Uses: Grease

1.3 Details of the supplier of the safety data sheet

Chevron Belgium NV
Technologiepark-Zwijnaarde 2
B-9052 Gent
Belgium
email : [email protected]

1.4 Emergency telephone number

Transportation Emergency Response
Europe: 0044/(0)18 65 407333
Health Emergency
Europe: 0044/(0)18 65 407333
Product Information
Product Information: FAX number: 0032/(0)9 293 72 22

SECTION 2 HAZARDS IDENTIFICATION

2.1 Classification of the substance or mixture

CLP CLASSIFICATION: Not classified as dangerous according to EU regulatory guidelines.

2.2 Label elements

Under the criteria of Regulation (EC) No 1272/2008 (CLP):
Not classified

- contains: N,N-Bis(2-ethylhexyl)-4-methyl-1H-benzotriazole-1-methylamine. May produce

____________________________________________________________________

Revisienummer: 5 1 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
 an allergic reaction.
N,N-Bis(2-ethylhexyl)-5-methyl-1H-benzotriazole-1-methylamine. May produce
an allergic reaction.

2.3 Other hazards Not Applicable

SECTION 3 COMPOSITION/ INFORMATION ON INGREDIENTS

3.2 Mixtures
This material is a mixture.

COMPONENTS CAS EC REGISTRATION CLP AMOUNT

NUMBER NUMBER NUMBER CLASSIFICATION
Zinc alkyl 68649-42-3 272-028-3 01-2119493635-2 Aquatic Chronic 0-1
dithiophosphate 7, 2/H411; Eye Dam. %weight
01-2119657973-2 1/H318; Skin Irrit.
3 2/H315

The full text of all CLP H-statements is shown in Section 16.

*Contains one or more of the following EINECS numbers: 265-090-8, 265-091-3, 265-096-0, 265-097-6,
265-098-1, 265-101-6, 265-155-0, 265-156-6, 265-157-1, 265-158-7, 265-159-2, 265-160-8, 265-161-3,
265-166-0, 265-169-7, 265-176-5, 276-735-8, 276-736-3, 276-737-9, 276-738-4, 278-012-2.

SECTION 4 FIRST AID MEASURES

4.1 Description of first aid measures

Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and
flush eyes with water.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if
contaminated. To remove the material from skin, use soap and water. Discard contaminated clothing and
shoes or thoroughly clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get
medical advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air,
move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs.

4.2 Most important symptoms and effects, both acute and delayed
IMMEDIATE SYMPTOMS AND HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation.
Skin: Contact with the skin is not expected to be harmful. High-Pressure Equipment Information:
Accidental high-velocity injection under the skin of materials of this type may result in serious injury. Seek
medical attention at once should an accident like this occur. The initial wound at the injection site may not
appear to be serious at first; but, if left untreated, could result in disfigurement or amputation of the affected
part.

Ingestion: Not expected to be harmful if swallowed.

Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause
respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at
____________________________________________________________________

Revisienummer: 5 2 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation
may include coughing and difficulty breathing.

DELAYED OR OTHER SYMPTOMS AND HEALTH EFFECTS: Not classified.

4.3 Indication of any immediate medical attention and special treatment needed
Not applicable.

SECTION 5 FIRE FIGHTING MEASURES

5.1 Extinguishing media

Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

5.2 Special hazards arising from the substance or mixture

Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne
solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds
will be evolved when this material undergoes combustion. Combustion may form oxides of: Phosphorus .

5.3 Advice for firefighters

This material will burn although it is not easily ignited. See Section 7 for proper handling and storage. For
fires involving this material, do not enter any enclosed or confined fire space without proper protective
equipment, including self-contained breathing apparatus.

SECTION 6 ACCIDENTAL RELEASE MEASURES

6.1 Personal precautions, protective equipment and emergency procedures

Eliminate all sources of ignition in vicinity of spilled material. Refer to Sections 5 and 8 for more information.

6.2 Environmental precautions

Stop the source of the release if you can do it without risk. Contain release to prevent further
contamination of soil, surface water or groundwater.

6.3 Methods and material for containment and cleaning up

Clean up spill as soon as possible, observing precautions in Exposure Controls/Personal Protection. Use
appropriate techniques such as applying non-combustible absorbent materials or pumping. Where feasible
and appropriate, remove contaminated soil and dispose of in a manner consistent with applicable
requirements. Place other contaminated materials in disposable containers and dispose of in a manner
consistent with applicable requirements. Report spills to local authorities as appropriate or required.

6.4 Reference to other sections

See sections 8 and 13.

SECTION 7 HANDLING AND STORAGE

7.1 Precautions for safe handling

General Handling Information: Avoid contaminating soil or releasing this material into sewage and
drainage systems and bodies of water.
Precautionary Measures: Do not get in eyes, on skin, or on clothing. Do not taste or swallow. Wash
thoroughly after handling.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this
material. To minimize this hazard, bonding and grounding may be necessary but may not, by themselves,
be sufficient. Review all operations which have the potential of generating and accumulating an electrostatic
____________________________________________________________________

Revisienummer: 5 3 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
charge and/or a flammable atmosphere (including tank and container filling, splash filling, tank cleaning,
sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use
appropriate mitigating procedures.
Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty
container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid,
and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and
cause injury or death. Empty containers should be completely drained, properly closed, and promptly
returned to a drum reconditioner or disposed of properly.

7.2 Conditions for safe storage, including any incompatibilities

Not Applicable

7.3 Specific end use(s):Grease

SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 2), applicable exposure limits, job activities, and
other substances in the work place when designing engineering controls and selecting personal protective
equipment. If engineering controls or work practices are not adequate to prevent exposure to harmful
levels of this material, the personal protective equipment listed below is recommended. The user should
read and understand all instructions and limitations supplied with the equipment since protection is usually
provided for a limited time or under certain circumstances. Refer to appropriate CEN standards.

8.1 Control parameters

No applicable occupational exposure limits exist for this material or its components. Consult local
authorities for appropriate values.
8.2 Exposure controls
ENGINEERING CONTROLS:
Use in a well-ventilated area.

PERSONAL PROTECTIVE EQUIPMENT

Eye/Face Protection: No special eye protection is normally required. Where splashing is possible, wear
safety glasses with side shields as a good safety practice.
Skin Protection: No special protective clothing is normally required. Where splashing is possible, select
protective clothing depending on operations conducted, physical requirements and other substances in the
workplace. Suggested materials for protective gloves include: Nitrile Rubber.
Respiratory Protection: No respiratory protection is normally required. No respiratory protection is
ordinarily required under normal conditions of use. In accordance with good industrial hygiene practices,
precautions should be taken to avoid breathing of material.. If user operations generate an oil mist,
determine if airborne concentrations are below the occupational exposure limit for mineral oil mist. If not,
wear an approved respirator that provides adequate protection from the measured concentrations of this
material. For air-purifying respirators use a particulate cartridge.

ENVIRONMENTAL EXPOSURE CONTROLS:

See relevant Community environmental protection legislation or the Annex, as applicable.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Attention: the data below are typical values and do not constitute a specification.
____________________________________________________________________

Revisienummer: 5 4 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
9.1 Information on basic physical and chemical properties
Appearance
Color: Amber
Physical State: Semi-solid
Odor: Petroleum odor
Odor Threshold: No data available
pH: Not Applicable
Freezing Point: No data available
Initial Boiling Point: >315°C (599°F) Minimum
Flashpoint: (Cleveland Open Cup) > 200 °C (> 392 °F) (Estimated)
Evaporation Rate: No data available
Flammability (solid, gas): No Data Available
Flammability (Explosive) Limits (% by volume in air):
Lower: Not Applicable Upper: Not Applicable
Vapor Pressure: <0.01 mmHg Maximum @ 37.8 °C (100 °F)
Vapor Density (Air = 1): >1 Minimum
Density: 0.92 g/ml @ 15°C (59°F) (Typical)
Solubility: Soluble in hydrocarbons; insoluble in water
Partition coefficient: n-octanol/water: No data available
Auto-ignition temperature: No data available
Decomposition temperature: No data available
Viscosity: 369mm2/s @ 40°C (104°F) Minimum
Explosive Properties: No Data Available
Oxidising properties: No Data Available

9.2 Other Information: No Data Available

SECTION 10 STABILITY AND REACTIVITY

10.1 Reactivity: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates,
peroxides, etc.
10.2 Chemical Stability: This material is considered stable under normal ambient and anticipated storage
and handling conditions of temperature and pressure.
10.3 Possibility of hazardous reactions: Hazardous polymerization will not occur.
10.4 Conditions to Avoid: Not applicable
10.5 Incompatible materials to avoid: Not applicable
10.6 Hazardous decomposition products: None known (None expected)

SECTION 11 TOXICOLOGICAL INFORMATION

11.1 Information on toxicological effects

Serious Eye Damage/Irritation: The eye irritation hazard is based on evaluation of data for product
components.
Skin Corrosion/Irritation: The skin irritation hazard is based on evaluation of data for product
components.
Skin Sensitization: The skin sensitization hazard is based on evaluation of data for product components.
Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation of data for product
components.

____________________________________________________________________

Revisienummer: 5 5 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of data for product components.

Acute Toxicity Estimate (oral): Not Applicable

Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on evaluation of data for similar
materials or product components.

Germ Cell Mutagenicity: The hazard evaluation is based on data for components or a similar material.

Carcinogenicity: The hazard evaluation is based on data for components or a similar material.

Reproductive Toxicity: The hazard evaluation is based on data for components or a similar material.

Specific Target Organ Toxicity - Single Exposure: The hazard evaluation is based on data for
components or a similar material.

Specific Target Organ Toxicity - Repeated Exposure: The hazard evaluation is based on data for
components or a similar material.

Aspiration Toxicity: No data available

ADDITIONAL TOXICOLOGY INFORMATION:

In accordance with the Directive 94/69/EC (21st ATP to DSD), Nota L, reference IP 346/92: "DMSO
Extraction Method", we have determined that the base oils used in this preparation are not carcinogenic.

SECTION 12 ECOLOGICAL INFORMATION

12.1 Toxicity
This material is not expected to be harmful to aquatic organisms. The product has not been tested. The
statement has been derived from the properties of the individual components.

12.2 Persistence and degradability

The product has not been tested. The statement has been derived from the properties of the individual
components.

12.3 Bioaccumulative potential

Bioconcentration Factor: No Data Available
Octanol/Water Partition Coefficient: No data available

12.4 Mobility in soil

No data available.

12.5 Results of PBT and vPvB assessment

This product is not, or does not contain, a substance that is a potential PBT or a vPvB.

12.6 Other adverse effects

No other adverse effects identified.

SECTION 13 DISPOSAL CONSIDERATIONS

____________________________________________________________________

Revisienummer: 5 6 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
13.1 Waste treatment methods
Use material for its intended purpose or recycle if possible. This material, if it must be discarded, may meet
the criteria of a hazardous waste as defined by international, country, or local laws and regulations. In
accordance with European Waste Catalogue (E.W.C.) the codification is the following: 12 02 12

SECTION 14 TRANSPORT INFORMATION

The description shown may not apply to all shipping situations. Consult appropriate Dangerous Goods
Regulations for additional description requirements (e.g., technical name) and mode-specific or
quantity-specific shipping requirements.

ADR/RID

NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

14.1 UN number: Not applicable
14.2 UN proper shipping name: Not applicable
14.3 Transport hazard class(es): Not applicable
14.4 Packing group: Not applicable
14.5 Environmental hazards: Not applicable
14.6 Special precautions for user: Not applicable

ICAO

NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

14.1 UN number: Not applicable
14.2 UN proper shipping name: Not applicable
14.3 Transport hazard class(es): Not applicable
14.4 Packing group: Not applicable
14.5 Environmental hazards: Not applicable
14.6 Special precautions for user: Not applicable

IMO

NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

14.1 UN number: Not applicable
14.2 UN proper shipping name: Not applicable
14.3 Transport hazard class(es): Not applicable
14.4 Packing group: Not applicable
14.5 Environmental hazards: Not applicable
14.6 Special precautions for user: Not applicable
14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC code: Not applicable

SECTION 15 REGULATORY INFORMATION

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
REGULATORY LISTS SEARCHED:
01=EU. Directive 76/769/EEC: Restrictions on the marketing and use of certain dangerous substances.
02=EU Directive 90/394/EEC: Carcinogens at work.
03=EU Directive 92/85/EEC: Pregnant or breastfeeding workers.
04=EU Directive 96/82/EC (Seveso II): Article 9.
____________________________________________________________________

Revisienummer: 5 7 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
05=EU Directive 96/82/EC (Seveso II): Articles 6 and 7.
06=EU Directive 98/24/EC: Chemical agents at work.
07=EU Directive 2004/37/EC: On the protection of workers.
08=EU Regulation EC No. 689/2008: Annex 1, Part 1.
09=EU Regulation EC No. 689/2008: Annex 1, Part 2.
10=EU Regulation EC No. 689/2008: Annex 1, Part 3.
11=EU Regulation EC No. 850/2004: Prohibiting and restricting persistant organic pollutants (POPs).
12=EU REACH, Annex XVII: Restrictions on manufacture, placing on the market and use of certain dangerous
substances, mixture & article.
13=EU REACH, Annex XIV: Candidate List of Substances of Very High Concern for Authorization (SVHC).

No components of this material were found on the regulatory lists above.

CHEMICAL INVENTORIES:
All components comply with the following chemical inventory requirements: AICS (Australia), DSL
(Canada), EINECS (European Union), PICCS (Philippines), TSCA (United States).

One or more components does not comply with the following chemical inventory requirements: KECI
(Korea).

15.2 Chemical safety assessment

No chemical safety assessment.

SECTION 16 OTHER INFORMATION

REVISION STATEMENT: This revision updates the following sections of this Material Safety Data Sheet:
1 - 16
Revision Date: MARCH 25, 2015

Full text of CLP H-statements:

H411; Toxic to aquatic life with long lasting effects
H318; Causes serious eye damage
H315; Causes skin irritation

ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:

TLV - Threshold Limit Value TWA - Time Weighted Average
STEL - Short-term Exposure Limit PEL - Permissible Exposure Limit
CVX - Chevron CAS - Chemical Abstract Service Number
NQ - Not Quantifiable

Prepared according to the criteria of EU Regulation 1907/2006 by the Chevron Energy Technology
Company, 100 Chevron Way, Richmond, California 94802.

The above information is based on the data of which we are aware and is believed to be correct as of the
date hereof. Since this information may be applied under conditions beyond our control and with which
we may be unfamiliar and since data made available subsequent to the date hereof may suggest
modifications of the information, we do not assume any responsibility for the results of its use. This
information is furnished upon condition that the person receiving it shall make his own determination of
the suitability of the material for his particular purpose.

____________________________________________________________________

Revisienummer: 5 8 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683
No Annex

____________________________________________________________________

Revisienummer: 5 9 of 9 High Temp Premium 2

Herzieningsdatum: MARCH 25, 2015 MSDS : 23683