Zener Diode
Features
• Planar Die construction
• 500mW Power Dissipation
• Ideally Suited for Automated Assembly Processes
Mechanical Data
• Epoxy meets UL 94 V-0 flammability rating
• Moisture Sensitivity Level 1
• Approx. Weight: 0.009 grams
Maximum Ratings @ Ta = 25°C unless otherwise specified
Characteristics Symbol Values Unit
Max. Forward Voltage @ If = 10mA Vf 0.9 V
Junction Temperature (Note 1) P(av) 500 mW
Operating and Storage Temperature Range Tj, Tstg -55 to +150 °C
Note:
1. Mounted on 5mm2 (0.013mm thick) land areas
Electrical Characteristics (Ta = 25°C unless otherwise specified)
Normal
Test Max. Reverse Leakage Max. Zener
Zener Max. Zener Impedance
Current Current Voltage
Part Number Marking Voltage
Temp.
Vz@Izt Izt Zzt@Izt@Izk=0.25mA Ir@Vr
Volts mA Ω Ω μA Volts %/°C
MMSZ5232B+ E2 5.6 20 11 1600 5 3 +0.038
MMSZ5234B+ E4 6.2 20 7 1000 5 4 +0.045
MMSZ5236B+ F1 7.5 20 6 500 3 6 +0.058
MMSZ5237B+ F2 8.2 20 8 500 3 6.5 +0.062
MMSZ5242B+ H2 12 20 30 600 1 9.1 +0.077
MMSZ5248B+ J3 18 7 21 600 0.1 14 +0.085
MMSZ5252B+ K2 24 5.2 33 600 0.1 18 +0.088
Note:
1. Standard Zener voltage tolerance is ±5% with a “B” suffix (e.g.: MMSZ5225B)
2. Specials Available Include:
A. Nominal zener voltages between the voltages shown and tighter voltage tolerances.
B. Matched sets.
3. Zener Voltage (Vz) Measurement. Guarantees the zener voltage when measured at 90 seconds while maintaining the lead
temperature (Tl) at 30°C, from the diode body.
4. Zener Impedance (Zz) Derivation. The zener impedance is derived from the 60 cycle ac voltage, which results when an AC
current having an rms value equal to 10% of the dc zener current (Izt or Izk) is superimposed on Izt or Izk.
5. Surge Current (IR) Non-Repetitive. The rating listed in the electrical characteristics table is maximum peak, non-repetitive,
reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test
current, Izt, per JEDEC registration.
www.element14.com
www.farnell.com
www.newark.com
Page <1> 22/06/17 V1.1
Zener Diode
Rating and Characteristic Curves
Typical Reverse Current Steady State Power Derating Effect of Zener Voltage on Zener
Impedance
Typical Forward Voltage Steady State Power Derating Typical Capacitance
Zener Voltage Vs. Zener Current Zener Voltage Vs. Zener Current Typical Leakage Current
www.element14.com
www.farnell.com
www.newark.com
Page <2> 22/06/17 V1.1
Zener Diode
Dimensions:
SOD-123
Dimensions
Inches mm
Dim.
Min. Max. Min. Max.
A 0.141 0.154 3.6 3.9
B 0.098 0.11 2.5 2.8
C 0.055 0.071 1.4 1.8
D 0.037 0.053 0.95 1.35
E 0.019 0.028 0.5 0.7
F - 0.008 - 0.2
G 0.016 - 0.4 -
H - 0.005 - 0.12
Part Number Table
Description Part Number
Zener Diode, 500mW 5.6V SOD-123 MMSZ5232B+
Zener Diode, 500mW 6.2V SOD-123 MMSZ5234B+
Zener Diode, 500mW 7.5V SOD-123 MMSZ5236B+
Zener Diode, 500mW 8.2V SOD-123 MMSZ5237B+
Zener Diode, 500mW 12V SOD-123 MMSZ5242B+
Zener Diode, 500mW 18V SOD-123 MMSZ5248B+
Zener Diode, 500mW 24V SOD-123 MMSZ5252B+
Important Notice : This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted
for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any
error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any
assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the
Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence.
Multicomp is the registered trademark of the Group. © Premier Farnell Limited 2016.
www.element14.com
www.farnell.com
www.newark.com
Page <3> 22/06/17 V1.1
