2016.

0 RANGE ROVER (LG), 206-09

ANTI-LOCK CONTROL -
TRACTION CONTROL
S P E C I F I C AT I O N S

General Specifications

ITEM SPECIFICATION

System Bosch 8.0 Anti-lock braking system with Electronic Brake Distribution (EBD),
type Corner Brake Control (CBC), Electronic Traction Control (ETC), Hill Descent
Control (HDC), Anti-roll Mitigation (ARM), Emergency Brake Assist (EBA), and
Dynamic Stability Control (DSC)

Wheel Bosch DF11im

speed
sensor
type

Wheel Front and rear knuckles with the active directional sensor acting on the
speed driveshaft pole wheel
sensor
location

Yaw Bosch DRS MM3.10

rate
sensor
type

Torque Specifications

DESCRIPTION NM LB-FT LB-IN

Front wheel speed sensor bolt 9 - 80

Front brake assembly dust protector 9 - 80

Rear wheel speed sensor bolt 9 - 80

Brake tube union nuts master cylinder to ABS module 20 15 -

Brake tube union nuts on ABS module to wheels M12 18 13 -

Brake tube union nuts on ABS module to wheels M10 16 12 -

ABS module mounting bracket nuts 9 - 80

ABS module fixing bolt to bracket 27 20 -

2016.0 RANGE ROVER (LG), 206-09

ANTI-LOCK CONTROL - TRACTION CONTROL

ANTI-LOCK BRAKE SYSTEM

MODULE - RHD (G2001615)

R E M O V A L A N D I N S TA L L AT I O N

RIGHT
HYDRAULIC
HAND
CONTROL USED
70.65.49 DRIVE, 1.3 +
UNIT - WITHINS
3000 CC,
RENEW
TDV6

GENERAL EQUIPMENT

EQUIPMENT NAME

Land Rover diagnostic equipment

REMOVAL

CAUTION:

If brake fluid is spilt on the paintwork, the affected area must be

immediately washed down with cold water.
 NOTES:

Make sure that all openings are sealed. Use new blanking caps.

Removal steps in this procedure may contain installation details.

! All vehicles

1.
WARNING:

Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

2. Remove the right-hand front wheel and tire.

Refer to: Wheel and Tire - GTDi 2.0L Petrol/TDV6 3.0L Diesel /TDV8
4.4L Diesel/V6 S/C 3.0L Petrol /V8 N/A 5.0L Petrol/V8 S/C 5.0L
Petrol (204-04 Wheels and Tires, Removal and Installation).

3.
NOTE:

LH illustration shown, RH is similar.

 "

4. Refer to: Right Air Cleaner (303-12E Intake Air Distribution and
Filtering - TDV8 4.4L Diesel, Removal and Installation).
Refer to: Right Air Cleaner (303-12A Intake Air Distribution and
Filtering - TDV6 3.0L Diesel - Gen 2/TDV6 3.0L Diesel, Removal and
Installation).
Refer to: Right Air Cleaner (303-12C Intake Air Distribution and
Filtering - V8 N/A 5.0L Petrol, Removal and Installation).
Refer to: Right Air Cleaner (303-12C Intake Air Distribution and
Filtering - V8 N/A 5.0L Petrol, Removal and Installation).

! Cold climate vehicles

5. Refer to: Radiator Grille (501-08 Exterior Trim and Ornamentation,

Removal and Installation).
6.
"

Torque: 7 Nm

7.
"

! All vehicles

8.
NOTE:

Vehicles with diesel engine only.

 "

9.
NOTE:

Vehicles with diesel engine only.

"
10.
"

Torque: 16 Nm

11.
"

Torque: 20 Nm
12.
"

Torque:
M10 16 Nm
M12 18 Nm

13.
"
14.
"

Torque: 9 Nm

15.
NOTE:

Do not disassemble further if the component is removed for

access only.
 "

Torque: 27 Nm

I N STA L L AT I O N

1.
NOTE:

Remove and discard all blanking caps.

To install, reverse the removal procedure.

2. 1. Refer to: Brake System Bleeding - Vehicles With: Standard

Brakes (206-00 Brake System - General Information, General
Procedures).

2. Refer to: Brake System Bleeding - Vehicles With: High

Performance Brakes (206-00 Brake System - General
Information, General Procedures).

3. 1. Hybrid Electric Vehicles (HEV) only.

2. Using the Land Rover approved diagnostic equipment,

calibrate the brake pedal sensor.
General Equipment: Land Rover diagnostic equipment
2016.0 RANGE ROVER (LG), 206-09

ANTI-LOCK CONTROL - TRACTION CONTROL

ANTI-LOCK BRAKE SYSTEM

MODULE - LHD (G2001614)

R E M O V A L A N D I N S TA L L AT I O N

RIGHT
HYDRAULIC
HAND
CONTROL USED
70.65.49 DRIVE, 1.3 +
UNIT - WITHINS
3000 CC,
RENEW
TDV6

GENERAL EQUIPMENT

EQUIPMENT NAME

Land Rover diagnostic equipment

REMOVAL

CAUTION:

If brake fluid is spilt on the paintwork, the affected area must be

immediately washed down with cold water.
 NOTES:

Make sure that all openings are sealed. Use new blanking caps.

Removal steps in this procedure may contain installation details.

1.
WARNING:

Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

2. Remove the left hand front wheel and tire.

Refer to: Wheel and Tire - GTDi 2.0L Petrol/TDV6 3.0L Diesel /TDV8
4.4L Diesel/V6 S/C 3.0L Petrol /V8 N/A 5.0L Petrol/V8 S/C 5.0L
Petrol (204-04 Wheels and Tires, Removal and Installation).

3. Refer to: Left Air Cleaner (303-12E Intake Air Distribution and
Filtering - TDV8 4.4L Diesel, Removal and Installation).
Refer to: Left Air Cleaner (303-12A Intake Air Distribution and
Filtering - TDV6 3.0L Diesel - Gen 2/TDV6 3.0L Diesel, Removal and
Installation).
Refer to: Left Air Cleaner (303-12C Intake Air Distribution and
Filtering - V8 N/A 5.0L Petrol, Removal and Installation).
Refer to: Left Air Cleaner (303-12D Intake Air Distribution and
Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

4.
NOTE:

Vehicles with diesel engine only.

 !

5.
!
6.
!

Torque: 16 Nm

7.
!

Torque: 20 Nm
8.
!

Torque:
M10 16 Nm
M12 18 Nm

9.
!
10.
!

Torque: 9 Nm

11.
NOTE:

Do not disassemble further if the component is removed for

access only.
 !

Torque: 27 Nm

I N STA L L AT I O N

1.
NOTE:

Remove and discard all blanking caps.

To install, reverse the removal procedure.

2. 1. Refer to: Brake System Bleeding - Vehicles With: Standard

Brakes (206-00 Brake System - General Information, General
Procedures).

2. Refer to: Brake System Bleeding - Vehicles With: High

Performance Brakes (206-00 Brake System - General
Information, General Procedures).

3. 1. Hybrid Electric Vehicles (HEV) only.

2. Using the Land Rover approved diagnostic equipment,

calibrate the brake pedal sensor.
General Equipment: Land Rover diagnostic equipment
2016.0 RANGE ROVER (LG), 206-09

ANTI-LOCK CONTROL - TRACTION CONTROL

FRONT WHEEL SPEED

SENSOR (G1509092)

R E M O V A L A N D I N S TA L L AT I O N

SENSOR
AND
HARNESS
ALL USED
70.65.30 - FRONT 1.1 +
DERIVATIVES WITHINS
WHEEL -
EACH -
RENEW

REMOVAL

NOTES:

Removal steps in this procedure may contain installation details.

Left-hand shown, right-hand similar.

1. Disconnect the battery ground cable.

Refer to: Specifications (414-00 Battery and Charging System -
General Information, Specifications).
2.
WARNING:

Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

3. Refer to: Fender Splash Shield (501-02 Front End Body Panels,
Removal and Installation).

4. Refer to: Brake Disc - Vehicles With: Standard Brakes (206-03 Front
Disc Brake, Removal and Installation).

5. Refer to: Brake Disc - Vehicles With: High Performance Brakes (206-
03 Front Disc Brake, Removal and Installation).

6.
CAUTION:

Before disconnecting or removing the components, make

sure the area around the joint faces and connections are
clean.

!
7.
!

Torque: 9 Nm

8.
CAUTIONS:

Make sure that the component is clean, free of foreign

material and lubricant.

Make sure that the sensor tip is clean and free of foreign
material.

!
 Torque: 9 Nm

I N STA L L AT I O N

1. To install reverse the removal procedure.

2016.0 RANGE ROVER (LG), 206-09

ANTI-LOCK CONTROL - TRACTION CONTROL

REAR WHEEL SPEED

SENSOR (G1509093)

R E M O V A L A N D I N S TA L L AT I O N

SENSOR
AND
HARNESS
ALL USED
70.65.31 - REAR 0.6 +
DERIVATIVES WITHINS
WHEEL -
EACH -
RENEW

REMOVAL

NOTES:

Removal steps in this procedure may contain installation details.

Left-hand shown, right-hand similar.

1. Disconnect the battery ground cable.

Refer to: Specifications (414-00 Battery and Charging System -
General Information, Specifications).
2.
WARNING:

Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

3. Refer to: Rear Wheel Arch Liner (501-08 Exterior Trim and
Ornamentation, Removal and Installation).

4.
CAUTION:

Before disconnecting or removing the components, make

sure the area around the joint faces and connections are
clean.

!
5.
CAUTIONS:

Make sure that the component is clean, free of foreign

material and lubricant.

Make sure that the sensor tip is clean and free of foreign
material.

Torque: 9 Nm

I N STA L L AT I O N

1. To install reverse the removal procedure.