CERTIFICATE

This is to certify that the CHEMISTRY project titled ‘STUDY OF

CONSTITUENTS OF ALLOYS’ has been successfully completed
by PRANAV PARASHAR of Class XII in partial fulfillment of
curriculum of CENTRAL BOARD OF SECONDARY
EDUCATION (CBSE) in the year of 2015-2016.

INTERNAL EXAMINER TEACHER IN-CHARGE

ACKNOWLEDGEMENT
It gives me great pleasure to express my gratitude towards our Chemistry teacher

MR. NARENDRA SINGH for his guidance, support and encouragement

throughout the duration of the project. Then I would like to thank my parents and

friends who have helped me with their valuable suggestions and guidance has been

helpful in various phases of the completion of the project. Without their motivation

and help the successful completion of this project would not have been possible.

Pranav Parashar
INDEX:
1. INTRODUCTION

2. SOME COMMON ALLOYS

3. PREPERATION OF ALLOYS

4. ANALYSIS OF AN ALLOY

5. EXPERIMENT 1

6. EXPERIMENT 2

7. USES OF ALLOY
Introduction:
An Alloy is a homogenous mixture of two or more metals or a non-metal.

An alloy of mercury with another metal is called amalgam.

Alloys are usually harder than their components but very often less ductile and less
malleable. Thus the hardness of gold is increased by addition of copper to it. The
melting point of an alloy is always lower than the melting points of the constituent
metals. Other properties such as reactivity towards atmospheric oxygen and moisture,
mechanical strength, ductility, color etc. also under goes a change when an alloy is
made from its constituents (metals). This change of properties is very useful and makes
an alloy beneficial.

Some of the alloys along with their composition is given below.

1. Brass:-

It consists copper-50-90%.

Zinc. : 20-40%

and small amounts of tin, lead and iron.

2. Bronze: It consists copper 60-90%.

3. Tin: 5-35%

and also contains small amounts of lead, iron and zinc.

Duralumin: It consists A1 : 95%, Cu = 4%

Mn = 0.5%, Mg = 0.5%

4. Gun Metal: It consists copper 85 - 90%

5. Zinc. : 1-3%

6. Tin: 8-12%
The composition of alloys may differ slightly depending upon the quality of the alloy
though the main components remain the same.
Some common alloys:
Amalgam

Any alloy of mercury is called an amalgam. Most metals are

soluble in mercury, but some (such as iron) are not. Amalgams are
commonly used in dental fillings because they have been relatively
cheap, easy to use, and durable. In addition, until recently, they
have been regarded as safe. They are made by mixing mercury
with silver, copper, tin, and other metals. The mercury content of
dental fillings has recently stirred controversy, based on the
potentially harmful effects of mercury.

Mercury amalgams have also been used in the process of mining

gold and silver, because of the ease with which mercury

amalgamates with them. In addition, thallium amalgam is used as the liquid material in
thermometers, because it freezes at -58°C, whereas pure mercury freezes at -38°C.

Brass

A decorative brass paperweight (left), along with zinc and copper

samples.

Brass is the term used for alloys of copper and zinc in a solid

solution. It has a yellow color, somewhat similar to gold. It was

produced in prehistoric times, long before zinc was discovered, by

melting copper with calamine, a zinc ore.

The amount of zinc in brass varies from 5 to 45 percent, creating

a range of brasses, each with unique properties. By comparison,

bronze is principally an alloy of copper and tin.

Despite this distinction, some types of brasses are called bronzes.

Brass is relatively resistant to tarnishing and is often used for
decorative purposes. Its malleability and acoustic properties have
made it the metal of choice for musical instruments such as the

trombone, tuba, trumpet, and euphonium. Although saxophones

And harmonicas are made out of brass; the saxophone is a
woodwind instrument, and the harmonica, a free reed aero phone.
In organ pipes designed as "reed" pipes, brass strips are used as
the "reed."

Aluminum makes brass stronger and more corrosion-resistant. It

forms a transparent, self-healing, protective layer of aluminum
oxide (Al2O3) on the surface. Tin has a similar effect and finds its
use especially in seawater applications (naval brasses).
Combinations of iron, aluminum, silicon, and manganese make brass
resistant to wear and tear.

Bronze

Bronze refers to a broad range of copper alloys, usually with tin

as the main additive, but sometimes with other element s such as

phosphorus, manganese, aluminum, or silicon. Typically, bronze is

about 60 percent copper and 40 percent tin. The use of bronze was particularly
significant for early civilizations, leading to the name "Bronze Age." Tools, weapons,
armor, and building materials such as decorative tiles were made
of bronze, as they were found to be harder and more durable
than their stone and copper predecessors.
In early use, the natural impurity arsenic sometimes created a superior natural
alloy, called "arsenical bronze."
Though not as strong as steel, bronze is superior to iron in nearly every application.
Bronze develops a patina (a green coating on the exposed surface), but it does not
oxidize beyond the surface. It is considerably less brittle than iron and has a
lower casting temperature. Several bronze alloys resist corrosion (especially by
seawater) and metal fatigue better than steel; they also conduct Heat
and electricity better than most steels.

Bronze has myriad uses in industry. It is widely used today for

springs, bearings, bushings, and similar fittings, and is particularly

common in the bearings of small electric motors. It is also widely
used for cast metal sculpture and is the most popular metal for
top-quality bells and cymbals.

Commercial bronze, otherwise known as brass, is 90 percent

copper and 10 percent zinc. It contains no tin

Preparation of alloys:
Alloys are prepared from the techniques of fusion, compression or simultaneous electro
- deposition. Generally the components are mixed together in proper properties in a
fuse clay crucible, melted and stirred with a piece of charcoal to avoid oxidation. The
molten mixture is now allowed to cool. When an alloy is obtained e.g. brass is prepared
by above melted.

Analysis of an alloy:
The complete analysis of an alloy involves two steps.

1. Qualitative Analysis:

This involves identification of the components of the alloys.

2. Quantitative Analysis:
This involves determination of the components of the alloy. It involves the separation of
the components from the alloy quantitatively followed by determination of percentage of
each component volumetrically or gravimetrically.

In this project we will carry out qualitative analysis only.

Objectives of Project:
In this project, our aim is to know the various metals present in the given sample of
alloy.
Aim: To analyze a sample of brass qualitatively.

Requirements: China dish, test-tube funnel, filter paper and common laboratory
reagents.

Theory:

Brass is an alloy of copper and zinc. with the following.

Composition:

Cu = 60-90% and Zn. = 10-40%.

Thus Cu and Zn. form the main constituents of brass. Both these metals dissolved in
50% of nitric acid due to formation of nitrates which are soluble.

3 Cu + 8HNO3 (Dil.) 3 Cu (NO3)2 + 2NO + 4H2O

or

Cu + 8H+ + 2NO3– 3 Cu+2 + 2NO + 4H2O

4Zn + 10HNO3 (Dil.) 4 Zn (NO2)2 + N2O + 5H2O

4Zn + 2NO3– + 10H+ 4 Zn+2 + N2O + 5H2O

The solution is boiled to expel the oxides of nitrogen and the resulting solution is tested
for Cu2+ and Zn+2 ions.

Procedure:
1. Place a small piece of brass in a china dish and heat this with minimum quantity of
50% HNO3 so as to dissolve the piece completely.

2. Continue heating the solution till a dry solid residue is obtained.

3. Dissolve the solid residue in dil. HCl and filter. Add distilled water to the filtrate.
4. Pass H2S gas through the filtrate. A black precipitate of copper sulphide is obtained.
Separate the black ppt. and keep the filtrate for the test of Zn+2 ions Dissolve black
ppt. by heating them with 50% HNO3. To this solution add ammonium hydroxide
solution. Appearance of deep blue coloration in the solution shows the presence of
copper ions in the solution.
5. To test Zn+2 ions, boil the filtrate to remove H2S gas, then add solid NH4Cl to this
and heat to dissolve NH4Cl. Add excess of NH4OH so that a solution is ammoniacal.
Now pass H2S gas through this ammoniacal solution. Dirty white or grey precipitation
indicate zinc. Separate the precipitates and dissolve it in minimum amount of dil. HCl.

Boil to expel H2S gas and add potassium Ferro cyanide solution, white or bluish white
ppt. confirm Zn+2 ions in the solution.

Result:

The given sample of brass contains copper and zinc. metals as the main constituents.
Aim: To analyze a sample of bronze qualitatively.

Requirements: China dish, test-tube funnel, filter paper and common laboratory
reagents.

Theory:

Bronze is an alloy of copper and tin with the following.

Composition:

Cu = 88-96% and Sn. = 4-12%.

Thus copper and zinc. form the main constituents of bronze. Both these metals
dissolved in nitric acid.

3 Cu + 8H+ + 2NO3– 3 Cu2+ + 2NO + 4H2O

4Sn + NO3– + 10 H+ 4 Sn+2 + NH4+ + 3H2O

(Cold and Dil. Acid)

Sn + 4NO3– + 4H+ H2Sn O3 + 2NO2 + H2O

(Conc. acid) (Metastannic Acid)

Excess of nitric acid is removed by heating the solution. The resulting solution now
would contain Cu+2 ions and metastannic acid. This solution is acidified with dil. HCl
and H2S gas is passed when the sulphides of copper and tin are formed.

Cu+2 + S2- CuS (Black ppt.)

H2SnO3 + 2H2S SnS2 (Black ppt.) + 3H2O

The sulphides are separated by boiling the ppt. with yellow ammonium sulphide when
SnS2goes into solution as thiostannate where as CuS is not affected.

SnS2 + (NH4)2S (NH4)2 SnS2 (Soluble)

Ammonium thiostannate.

CuS + (NH4)2S CuS (Unaffected)

Black ppt.
The soluble black ppt. is tested for Cu+2 ions and the solution is tested for Sn2+ ions
as in elementary qualitative analysis.

Procedure:
1. Take about 1g. of small pieces of bronze in a china dish and add to it 5-10 ml. of dil.
HNO3.
2. Heat the contents slowly to dissolve copper and tin completely and then boil the
contents to a paste to remove excess of HNO3. All this is carried out in cup board.

3. Dissolve this dry mass in distilled water containing HCl (1:1) to get a clear solution.
4. Transfer the solution in a test tube and pass H2S in excess i.e. till the precipitation is
complete. Filter and reject the filtrate.
5. Take the black ppt. in a test tube and add to it 2-3 ml. of yellow ammonium sulphide
and heat. Filter the contents. Black residue is tested for Cu+2 ions and filtrate is tested
for Sn+2ions.

6. Analysis of black residue:

Transfer a little of the black ppt. into a test tube. Add to it 2-3 ml. of 50%. HNO3 and
boil the contents of the tube. A light blue or green sol. indicates the presence of Cu+2.
Divide this sol. into two parts.
(a) To one part add excess of NH4OH a deep blue coloration confirms the presence of
Cu+2 ions.
(b) Acidify the second part with acetic acid and add K4 [Fe (CN)6] i.e. potassium
ferrocyanide solution. A reddish brown ppt. confirms the presence of Cu+2 ions.

7. Analysis of filtrate:
Boil the filtrate with 1 ml. of dil. HCl. A yellow ppt. is obtained. Dissolve in 1 ml. conc.
HCl. To this solution add 0.5 g. of zinc. dust and boil it for 2-3 minutes. Filter and to
filtrate add 1-2 ml. of mercuric chloride solution. A white ppt. turning grey on standing
confirms the presence of Sn+4 ions.

Result:

The given sample of bronze contains - Cu and Sn as the main constituents.

Uses of Alloys:

i) To modify chemical reactivity:-

When sodium is used as reducing agent it is too reactive to be used but its alloy with
mercury, called sodium amalgam can be safely used as reducing agent.

ii) To increase hardness:-

Hardness of gold is increased by adding copper to it. Also zinc is added to copper to
make copper hard in form of brass.

iii) To increase tensile strength:-

Nickeloy, an alloy of Nickel (1%), Copper (4%) and aluminium (95%) has high tensile
strength.

iv) To lower the melting point:-

Solder metal which is an alloy of Sn (30%) and Pb (70%) has very less meting point as
compared to melting points of Sn and Pb.

v) To modify the color:-

Aluminium bronze an alloy of Cu and Al has beautiful golden color.

vi) To resist corrosion:-

Iron gets rusted and corroded. Its corrosion takes place with time but stainless steel, an
alloy of iron and carbon get not rusted the composition of stainless steel is :

Iron - 98%

Carbon - 2%