Thinner MSDS

THINNERS - MSDS
Classified as hazardous
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

Product Name: THINNERS
Recommended Use: Industrial Solvent
Company: Omega International Coatings Pty Ltd
Address: 111, Kurrajong Av., Mt Druitt NSW 2770
Telephone Number: (02) 98320000
Emergency Telephone: (02) 96770566
2. HAZARDOUS IDENTIFICATION
Hazardous Classification: Hazardous substance according to the criteria of
NOHSC. Dangerous goods classification according to
the Australian
Dangerous Goods Code.
Risk Phrase(s): R11 – Highly flammable

R20 – Harmful by inhalation
R36/37 – Irritating to eyes and respiratory
system
Safety Phrase(s): S2 – Keep out of reach of children

S9 – Keep container in a well-
ventilated place
S16 – Keep away from sources of ignition
S25 – Avoid contact with eyes
S29 – Do not empty into drains
S33 – Take precautionary measures against
static discharges
3. COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients: Name: CAS No: Proportion

(w/w):
X3B 108-88-3 95%
Methyl Ethyl Ketone 78-93-3 5%
Omega International Coatings Pty Ltd – MSDS 1

4. FIRST AID MEASURES
Inhalation:
Remove from contaminated area. Apply artificial respiration if not breathing.
Seek medical assistance.
Ingestion:
If poisoning occurs, contact a Doctor or Poisons Information Centre. Phone
131126 in Australia. If swallowed, do not induce vomiting. Give a glass of
water.
Skin:
If skin contact occurs, remove contaminated clothing and wash skin
thoroughly. Remove contaminated clothing. Wash clothing before reuse.
Eye:
If in eyes, hold eyes open, flood with water for at least 15 minutes and see a
doctor.
First Aid Facilities:

Provide eye baths and safety showers close to areas where splashing may
occur.
Advice to Doctor:
Due to the risks of lung damage by aspiration of this product, gastric lavage
should only be undertaken after endotracheal intubation.
5. FIRE FIGHTING MEASURES

Substantial Extinguishing Media:
Use foam or dry agent extinguisher.
Special Protective Equipment for Fire Fighters:

Wear chemical goggles or face shield. Wear protective clothing as necessary
to avoid skin contact. Wear chemical resistant gloves. Respiratory protection
should be used if there is a risk of exposure to high vapour concentrations.
Specific Hazards:
This product is extremely flammable. Vapours are heavier than air and will
“travel” to low-level areas eg. Sumps, drains, etc. and flashback. Precautions
should be taken to eliminate the build up of explosive mixtures.
Hazchem Code:
3[Y]E
6. ACCIDENTAL RELEASE MEASURES

Emergency Procedures:
All Purpose Thinners is a flammable liquid. Vapour may form explosive
mixtures with air. Avoid heat and all ignition sources. Use only in well-

ventilated areas. Flameproof equipment is necessary in any area where
product is being used. Product transfer and storage equipment must be
earthed. Prevent build-up of flammable vapours. Consult AS1940 for further
information on safe storage and handling of flammable liquids. Handle in
accordance with state or territory regulations for flammable liquids.
7. HANDLING AND STORAGE

Precautions for Safe Handling:
Wear chemical goggles or face shield. Wear protective clothing as necessary
to avoid skin contact. Wear chemical resistant gloves. Respiratory protection
should be used if there is a risk of exposure to high vapour concentrations.
This product is harmful if it is inhaled. Respirators should comply with AS1716
or an equivalent approved by a state/territory authority.
Conditions for Safe Storage:

Store in a cool well-ventilated area away from heat and ignition sources.
Containers should always be kept closed in storage and properly labeled.
Many plastics may be unsuitable as storage and handling materials. Store
only in original or approved containers.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION

National Exposure Standards:
Substance STEL STEL TWA TWA

mg/m³ ppm mg/m³ ppm
Lacquer Thinners - 150 - 50
Engineering Controls:
Keep away from sources of ignition. Take precautionary measures against
static discharges. Provide sufficient ventilation to control exposure levels
below the exposure standards. Use local exhaust ventilation at sources of air
contamination such as open process equipment. Dangerous concentrations
may exist in areas with poor ventilation such as confined spaces.
Respiratory Protection:
Respiratory protection should be used if there is a risk of exposure to high
vapour concentrations. This product is harmful if it is inhaled. Respirators
should comply with AS1716 or an equivalent approved by a state/territory
authority.

Eye Protection:
Wear chemical goggles or face shield.
Hand Protection:
Wear chemical resistant gloves.
Body Protection:
Wear protective clothing as necessary to avoid skin contact.
9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance: Clear, colourless, mobile liquid with
hydrocarbon odour
Boiling Point: 80-110°C
Solubility in Water: Miscible with water
Specific Gravity: 0.84g/mL
Vapour Pressure: 50mm Hg @ 20°C
Vapour Density (Air = 1): 2.0
Volatile Component: 100%
Flash Point: 1
Flammability: HIGHLY FLAMMABLE. This product should
be stored and
used in a well-ventilated area away from
naked flames,
sparks and other sources of ignition.
Electrically link and
ground metal containers for transfers of the
product to
prevent accumulation of static electricity.
Keep the container
tightly closed.
10. STABILITY AND REACTIVITY

Chemical Stability:
Stable under normal use conditions.
Conditions to Avoid:
Heat, direct sunlight, open flames or other sources of ignition and
incompatibles.
11. TOXICOLOGICAL INFORMATION

Inhalation:
Avoid breathing vapour or spray mist. Vapour concentrations are irritating to
nose and throat resulting in possible headaches, dizziness, and lack of
coordination, nausea and possible loss of consciousness.

Ingestion:
All Purpose Thinners is classified as flammable and harmful if ingested.
Exposure to this product may result in nausea, dizziness and lack of
consciousness. Vomiting may cause the product to be aspirated in the lungs
possibly resulting in chemical pneumonitis.
Skin:
Avoid contact with skin. Exposure may cause the product to be absorbed into
the skin promoting the potential for over-exposure.
Eye:
Avoid contact with eyes. Product may cause moderate to severe eye irritation
and pronounced inflammation.
Chronic Effects:
Repeated or prolonged contact may cause irritant contact dermatitis.
12. ECOLOGICAL INFORMATION

Ecotoxicity:
A low potential to affect aquatic organisms.
A low potential to affect secondary waste treatment microbial metabolism.
A low potential to affect the growth of some plant seedlings.
Environment Protection:
Do not allow product to enter drains, waterways or sewers.
13. DISPOSAL CONSIDERATIONS

Waste Disposal:
Prevent entry into drainage systems, sewers and waterways.
14. TRANSPORT INFORMATION

Transport Information:
All Purpose Thinners is classified as flammable under the Australian Code for
the Transportation of Dangerous Goods by Road and Rail.
U.N Number: 1993

Proper Shipping Name: All Purpose Thinners
DG Class: 3
Hazchem Code: 3[Y]E
Packing Group: ll

15. REGULATORY INFORMATION
Poisons Schedule: S6
National and or International
Regulatory Information: Classified as hazardous according to criteria
of National
Occupational Health and Safety Commission
(NOHSC).
Packaging & Labeling: As required by the ADG Code. As required by
the National Code of Practice for the Labeling
of Workplace
substances. As required by the Standard for
the Uniform
Scheduling of Drug and Poisons.
16. OTHER INFORMATION

References: (1) National Code of Practice for the preparation of Material
Safety Data Sheets 2nd Edition [NOHSC:2011(2003)],
Contact Point: Director Telephone: (02) 98320000
DISCLAIMER: All information given in this data sheet and by the company’s technical staff is compiled
from the information currently available to the company. The company accepts no responsibility
whatsoever for its accuracy, or for any results which may be obtained by customers. Any customer who
relies upon any advice or information given in this data sheet by the company or by its technical staff
does so entirely at its own risk, and the company will not be liable for any loss or damage thereby
suffered notwithstanding any want of care on the part of the company or its staff in compiling or giving
the advice or information.
ISSUE DATE: January 2008

Thinner MSDS

Uploaded by

Copyright:

Available Formats

Thinner MSDS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Thinner MSDS

Uploaded by

Copyright:

Available Formats

THINNERS - MSDS

1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

Risk Phrase(s): R11 – Highly flammable

Safety Phrase(s): S2 – Keep out of reach of children

Ingredients: Name: CAS No: Proportion

Omega International Coatings Pty Ltd – MSDS 1

First Aid Facilities:

5. FIRE FIGHTING MEASURES

Special Protective Equipment for Fire Fighters:

6. ACCIDENTAL RELEASE MEASURES

Omega International Coatings Pty Ltd – MSDS 2

7. HANDLING AND STORAGE

Conditions for Safe Storage:

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Substance STEL STEL TWA TWA

Omega International Coatings Pty Ltd – MSDS 3

9. PHYSICAL AND CHEMICAL PROPERTIES

10. STABILITY AND REACTIVITY

11. TOXICOLOGICAL INFORMATION

Omega International Coatings Pty Ltd – MSDS 4

12. ECOLOGICAL INFORMATION

13. DISPOSAL CONSIDERATIONS

14. TRANSPORT INFORMATION

U.N Number: 1993

Omega International Coatings Pty Ltd – MSDS 5

16. OTHER INFORMATION

Contact Point: Director Telephone: (02) 98320000

ISSUE DATE: January 2008

Omega International Coatings Pty Ltd – MSDS 6

You might also like