(En) M Sew - Soft Instruction

M A u tom a tic S e w i n g Contr ol Sy s te m
Automatic Sewing Control

System
(Use of Software )
Operation Instruction
Version: VER2.0

Content
1．Software installation ...................................................... 1
1.1 Software installation process ........................................................................................................................1
1.2 Software uninstall process ............................................................................................................................4
2. Basic use of the software .................................................. 5
2.1 Graphic illustration of each place of the main interface:： ..........................................................................5
2.2 Open and save the documents .......................................................................................................................5
2.3 Operation instructions of the basic keys on the main interface ....................................................................6
2.4 Operation introductions of the graphical interface .......................................................................................8
2.4.1 Instructions of the graph operations...................................................................................................8
2.4.2 Right-click pop-up pull-down menu ..................................................................................................9
2.5 Fast sorting of the main interface graphs ....................................................................................................10
3 Layer change .............................................................. 12
4. Copy of the current graph ................................................. 12
5. Modify the current graph .................................................. 13
5.1. Adding points .............................................................................................................................................14
5.2. Graph-disassembling .................................................................................................................................16
5.3. Special sewing ...........................................................................................................................................17
6. Batch setting ............................................................. 24
6.1 Merging.......................................................................................................................................................25
6.2 Rotation ......................................................................................................................................................26
6.3 Horizontal mirroring ...................................................................................................................................28
6.4 Vertical mirroring........................................................................................................................................29
6.5 Reverse .......................................................................................................................................................30
6.6 Left-right sorting .........................................................................................................................................32
6.7 Top starting point ........................................................................................................................................34
6.8 Change the head and tail lengths ................................................................................................................35
7. Set the current layer ..................................................... 36
8. Set the datum point ....................................................... 38
8.1 Set the datum point .....................................................................................................................................38
8.2 Cancel the datum point ...............................................................................................................................40
9. Function of code setting .................................................. 41
9.1 Setting of the code ......................................................................................................................................42
9.2 Cancel the code ...........................................................................................................................................45
10. Mirroring and rotation ................................................... 46
10.1 Horizontal mirroring .................................................................................................................................48
10.2 Vertical mirroring ......................................................................................................................................49
10.3 Rotation ....................................................................................................................................................51
11. Sewing simulation ........................................................ 52
12. Zigzag sewing ............................................................ 54
1
1．Software installation
1.1 Software installation process
Click next step:
1
Set the paths and directories of the software to be installed, click next step:
Set the name of the shortcut key in the start menu after the software is installed, and click
next step:
2
Choose whether you will create desktop running shortcut (effective in the XP system) and
click next step:
Pop up all the configuration option parameters, then click “install”:
3
After installation is completed, choose running the software, then enter the following
software main interface:
1.2 Software uninstall process
Click begin —> all programs –> numerical control compilation software --> uninstall the
numerical control compilation software，
Click the icon “uninstall the numerical control compilation software” to enter the following
uninstall picture:
4
Click the button “yes”, then the compilation software will be uninstalled from this computer.
2. Basic use of the software
2.1 Graphic illustration of each place of the main interface:：
Shape scope Layer color
Layer Shape
list list
Shapes show
2.2 Open and save the documents
No. Icon Shortcut key Name Functions and contents
Open the Click this button to open the pattern

1 Ctrl+O
document document needed
Click this button to save the drafted
2 Ctrl+S Save as pattern document, with the format as
*.ntp
The following four kinds of documents are supported: plt, dxf, AI, ntp
5
2.3 Operation instructions of the basic keys on the main interface
No. Icon Shortcut key Name

Operation Click this button to return to the
1
back previous step operation
Operation Click this button to return to the next
2
redoing step operation
3 zoom in Click this button to zoom in the picture
Click this button to zoom out the

4 Zoom out
picture
Display Click this button to return to the
5
recovery original state of the main interface
Click this button, when the cursor
Drag the
6 becomes the hand shape, the graph can
graph
be dragged.
Click this button to cancel the
Normal operations of zooming in, zooming out,
7
operation dragging and so on, and restore the
normal operation state.
6
Show the related helping information of

8 About
this software.
Move up or down the position serial
Move up and
9 number of the current layer(left) or the
down
graph (right)
Change the position serial number of
Change the
10 the current layer(left) or the graph
serial number
(right)
Horizontal Click this button for the mirror image
11
mirror image in the X-axis direction of the graph
Vertical Click this button for the mirror image
12
mirror image in the Y-axis direction of the graph
To set different rotation angles, press

Rotation
13 the rotation button, the graph rotate to
operation
the corresponding angle
Graph Click this button to delete the selected

14
cancellation graph
Set the moving distance in the “moving

distance picture frame”, then click the
Key of
15 right and left keys to move along the X
moving
axis, press the up and down keys to
move along the Y axis.
Click this button to change a certain

Change the
16 graph on the same layer to another
layer
layer
Pop up the current copying interface,
Copy of the
17 you can conduct copy operation to the
current graph
current graph or the current layer.
Pop up the dialog box of modifying the
current graph. Modify the current
Modify the
18 graph, including graph-disassembling,
current graph
inserting now points, adding special
sewing sections and so on.
Enter the batch processing interface,
Batch
19 take the current layer as the object and
processing
process the graphs in it.
Pop up the interface of setting the
Setting of the
20 current layer. You can set according to
current layer
the parameters and generate graph
7
sewing points.
Pop up the datum point setting dialog
Set as the
21 box, select whether you’ll set the
datum point
current sewing point as the datum pint.
Pop up the sewing simulation dialog
Sewing
22 box, conduct the sewing simulation
simulation
process of the pattern.
If only selecting the current sewing
Sewing point
point, then pop up the code setting
23 code
window for you to set the control word
attributes of the current sewing point.
Display the
24 Display the patterns of all the layers
whole pattern
Display the Only display the pattern of the current
25
layers layer
Display the
Whether to display the serial number of
26 serial
the pattern or the sewing point
numbers
The button of exiting the main
interface. When clicking it, there will
27 Exit
popped up dialog box, confirm whether
you want to exit.
2.4 Operation introductions of the graphical interface
On the graphical operation interface, you can zoom in and zoom out the graph conveniently.
Click the right-hand button of the mouse, select the graph or the sewing point, click the right-hand
button to pop up the pull-down list.
2.4.1 Instructions of the graph operations
No. Operation instructions Functions and contents
You zoom in the graph with the current mouse position

1 Mouse wheel up
as the center
You zoom out the graph with the current mouse position
2 Mouse wheel down
as the center
Click the right-hand button When clicking the right-hand button of the mouse and
3
of the mouse and drag drag, you drag the graph
8
Note: when pressing the right-hand button, if you click the right-hand button once and select the
graph, there will pop up the pull-down list; Long press the right-hand button, it will enter the
graph-dragging mode, then you move the mouse for dragging operation.
2.4.2 Right-click pop-up pull-down menu
a) Select the graph, right click, it pops up:
b) Select the current sewing point then have right click:：
9
Instructions of the pop-up menu:
No. Operation names Functions and contents
After clicking, it pops up the dialog box of code setting, then add
1 Code the control words and sewing point attributes to the current sewing
point.
Set the sewing speed numbers of all the selected sewing points by
2 Batch processing
batch processing.
Add a new sewing point between the current point and the point
3 Insertion point
before it.
2.5 Fast sorting of the main interface graphs
（1） Click the selected graph 7 as the beginning graph of sorting.

（2） Set the beginning point serial number of sorting, assuming it’s “1”.
（3） Click confirm then the serial number of the currently selected graph turns into “1”.
10
2 3
（4） Press the Ctrl button+the mouse clicking graph B, then the graph B’s serial number
becomes “2”.
（5） In the same way you can specify the graphs’ serial numbers 3、4、….N successively.
（6） When the sorting exceeds the range, it pops up the message:
11
3 Layer change
There are to ways to pop up the dialog box of “layer change”

1）、Click the “layer change” button on the main interface.
2）、After selecting the graph, right click then it pops up the pull-down list, click the “layer
change”.
First select the layer the current graph needed to be changed to:
1、 When selecting the “new layer”, there will add a layer including the current layer.
2、 Choose other payer A, then the current layer will be changed to other layer A.
4. Copy of the current graph
There are two ways to pop up the dialog box of “copy the current graph”:
1）、Click the “copy the current graph” button on the main interface.
2）、After selecting the graph, right click for the pop-up pull-down list. Click “copy the current
graph”.
The interface of “copy the current graph” shows:
12
No. Operation name Functions and contents
Copy the whole layer, the operation object is the

1 Copy the current layer
whole current layer
Conduct copy operation according to the vertical
2 Copy the vertical mirror image
mirroring principal.
Conduct copay operation according to the
3 Copy the horizontal mirror image
horizontal mirroring principal.
Refer to the horizontal distance for the graph offset
4 Horizontal offset distance
after copying.
Refer to the vertical distance for the graph offset
5 Vertical offset distance
after copying.
Note:
1、 Choose “copy the current layer”, then the operation object is the whole layer, or it will
be。the currently selected graph.
2、 The vertical mirroring and the horizontal mirroring are mutually exclusive, you can only
select one of them.
5. Modify the current graph
After selecting the graph, touch “modify the current graph” to enter the interface of
modifying the current graph.
13
Interface of modifying the current graph
5.1. Adding points
On the interface of modifying the current graph, you can add points to the current graph.
Here are the operations:
1. Adding points
（1）Set the length to the first point.
14
（2）Adding points
After touching the key “add point”
15
After touching the key “implement” , the point adding operation is completed.
5.2. Graph-disassembling
On the current graph modification interface, you can disassemble the current graph. Here are
the operations:
1. Graph disassembling
（1）Choose the “disassemble point”
Touch the button “move forward” or “move back ”, or use the mouse to choose the node
position of the graph.
16
（2）Disassemble the graphs

After touching the key “disassemble the graph”, the graph disassembling operation.
Disassemble the current graph into 2 graphs
5.3. Special sewing
On the current graph setting interface, you can set the local special sewing and the special
graph sewing.
1. Local special sewing
（1） Choose the type of special sewing
When choosing the “special pitch”, generate the sewing point according to the special pitch;
17
When choosing “set rate”, sew according to the set speed (medium high speed, medium low
speed, low speed)
（2）Choose the starting point of the special sewing.

Touch the key “move forward” or “move back”, or use the mouse to select the node position
of the graph. Then touch the “starting point” button to set the current node of the graph as the
starting point of the special sewing.
18
（3）Choose the end point of the special sewing.

Touch the key “move forward” or “move back”, or use the mouse to select the node position
of the graph. Then touch the “end point” button to set the current node of the graph as the end
point of the special sewing.
19
（4）Touch the button “local special sewing”.
After exiting the current graph modification interface, use black bold line to show the graph with
special sewing.
20
2. Special sewing of the graphs

（1）Choose the type of special sewing
When choosing the “special pitch”, the sewing point is generated according to the special
pitch;
When choosing “superpose sewing”, the superpose sewing will be realized according to the
set superpose sewing times;
When choosing “set rate”, sew according to the set speed (medium high speed, medium low
speed, low speed)
（2）Choose graphs.
21
Touch “the last graph” or “the next graph” key to choose the whole graph. The graph is shown
in blue.
（3）Touch the key “special graph sewing”

Touch the key “special graph sewing” and the graph is shown in black.
22
After exiting the current graph modification interface, the graph with special sewing is shown
in black bold lines .
3. Cancel the special sewing

Touch the key “undo”/ “clear” to cancel the already set special sewing.
23
6. Batch setting
On the batch processing interface, conduct batch modification to the graphs in the current
layer.
Batch processing interface

24
[Merge]: merge the graphs of which the lengths are less than the merging length.
[Rotate]： Rotate the selected graph.
[Horizontal mirroring]：conduct horizontal mirroring to the selected graph.
[Vertical mirroring]：Conduct vertical mirroring to the selected graph.
[Reverse direction]： Reverse the selected graph.
[up-down sorting]：Conduct up-down sorting on the selected graphs.
[down-up sorting]： Conduct down-up sorting on the selected graphs.
[Left-right sorting]： Conduct left-right sorting on the selected graphs.
[Right-left sorting]： Conduct right-left sorting on the selected graphs.
[Top starting point]： Select the graph and set it as the top starting point.
[Bottom starting point]： Select the graph and set it as the bottom starting point.
[Left-end starting point]： Select the graph and set it as the left-end starting point.
[Right-end starting point]： Select the graph and set it as the right-end starting point.
[Layer change]： Change the layers of the selected graphs.
[Select all]：Select all the graphs.
[Delete the selected]：Delete the selected graph.
6.1 Merging
Select graph 1 and graph 2, after setting the merging lengths and touching the “merge” button,
graph 1 and graph 2 are merged into one.
Before merging
25
After merging
6.2 Rotation
After setting the rotation angle, touch the “rotate” button to rotate the selected graph.
26
Before rotation
27
After rotation
6.3 Horizontal mirroring
After touching the button of “horizontal mirroring”, conduct horizontal mirroring to the
selected graph with the graph’s x direction as the center.
28
Y direction is central mirroring
6.4 Vertical mirroring
After touching the button of “vertical mirroring”, conduct vertical mirroring to the
selected graph with the graph’s Y direction as the center.
29
Y direction is central
mirroring
6.5 Reverse
After touching the “reverse” button, reverse the graph’s sewing-start direction.
30
Before reversing
31
After reversing
6.6 Left-right sorting
After touching the button of “left-right sorting”, conduct left-right sorting to the selected
graph.
32
Before left-right sorting
After left-right sorting
33
6.7 Top starting point
After touching the “top starting point”, set the selected graph as the top starting point.
Before the operation of top starting point
34
After the operation of top starting point
6.8 Change the head and tail lengths
On the batch processing interface, you can change the head and tail lengths of the current
graph. First set “change the head length” and “change the tail length”, then touch “implement”
button to complete the operation of changing the head and tail lengths.
Before changing
35
After changing
7. Set the current layer
Double click “layer 1” or touch the current layer setting button to enter the interface of
setting the current layer. In the interface of setting the current layer, set the parameters in the
current layer.
36
Interface of setting the current layer
[Output or not]: Set whether output the current layer or not.

[Change head]: No.1 sewing head, No.2 brush end, No.3 template head.
[Turn lines to dots ]: Conduct horizontal mirroring to the selected graph.
[Pitch]: Set the pitch of the current graph.
[Head-tail reverse sewing]: Set the head-tail reverse sewing to the current layer.
Starting reverse sewing stitches: set the stitches of reverse sewing at the beginning of
the graph.
Starting reverse sewing stitches: set the stitches of reverse sewing at the beginning of
the graph.
Ending reverse sewing stitches: set the stitches of reverse sewing at the end of the graph.
Ending reverse sewing stitches: set the stitches of reverse sewing at the end of the graph.
[Head-tail retracting sewing]: Conduct up-down sorting to the selected graphs.
Starting retracting sewing stitches: set the stitches of retracting sewing at the beginning
of the graph.
Starting retracting sewing multiple: set the multiple of retracting sewing at the beginning
of the graph.
Ending retracting sewing stitches: set the stitches of retracting sewing at the end of the
graph.
37
Ending retracting sewing multiple: set the multiple of retracting sewing at the end of the graph.
[Setting of the inflection point]: Conduct up-down sorting to the selected graph.
Inflection point Angle: when he inflection point angle is less than the setting number, set
the sewing needle as the inflection deceleration point .
Deceleration stitches: Set the stitches of the inflection pint deceleration.
[Fastening stitches of the closed graph]: Set the fastening stitches of the closed graph.
8. Set the datum point
After the pattern becomes the sewing point data, you can choose the sewing point and set it as the
datum point.
8.1 Set the datum point
Select the sewing point needing to be set as the datum point, and the current point becomes the
way the following picture shows:
38
Click “set as the datum point” button, pop up the interface as the following picture. Select it and
set the datum point as 1.
The set datum point is as the following picture. Use the red cross to represent the datum point set.
In the same way, selected the sewing point of the datum point 2.
39
Select “set the current graph as datum 2”
The setting of datum 2 is completed
8.2 Cancel the datum point
After completing the setting of the datum point, if you think it inappropriate and needed to be
canceled, first you select the datum point needing to be canceled
40
Click the button “set as the datum point” and the following interface pops up.
Select “clear the datum point” then exit. The current datum point is cleared.
9. Function of code setting
After the graph becomes the mode of sewing points, you can add some other attributes in the
sewing points.
41
9.1 Setting of the code
Step 1: Choose the sewing points needing to be added
42
Click the code to enter the setting interface. If the current sewing point has the code, it will
demonstrate. If not, it shows the following picture:
Step 2: Selected the code that can be set, for example, if we are going to set the trimming at
the current point, then first select trim, click the red selected area, or select the trim and double
click.
43
After setting completion, it becomes the following state
Step 3: set speed limit, middle presser foot, tension and delay time. The speed limit is the limit
of the highest speed of the sewing point, the middle presser foot refers to the height change of the
middle presser foot beginning from the sewing point. The tension value is also the change starting
from the sewing point. The delay time refers to the delay time of the sewing point.
Select the speed limit and set the limited speed. Click the arrow to set the current speed limit
number, or double click the speed limit to set the current number. After setting completing, it
shows the following picture:
44
9.2 Cancel the code
After setting the code, if you want to cancel the code set for the current sewing point, you can
choose the code set.
Double click the selected information or click the icon shown in the demonstration picture, then
the set code is canceled.
45
10. Mirroring and rotation
The mirroring and rotation under the main interface are the operations targeting the whole
picture. After it turns into the sewing point, you can also conduct rotation and mirroring operations
to the whole graph.
46
The pattern becomes the sewing point
47
10.1 Horizontal mirroring
After the horizontal mirroring of the whole graph
After the horizontal mirroring of the sewing points of the whole graph
48
10.2 Vertical mirroring
After the vertical mirroring of the whole graph
49
After the vertical mirroring of the sewing points of the whole graph
50
10.3 Rotation
After rotating the whole graph
After rotating the sewing points of the whole graph
51
11. Sewing simulation
Click “sewing simulation” on the main interface to view the sewing track of the sewing point.
52
Click the button “start”, the sewing point draws the pattern in order, drag the speed roller to
change the sewing speed during the sewing stimulation process.
53
Click the “End” button to end the sewing simulation.
12. Zigzag sewing
After the pattern becomes the sewing point data, you can choose the sewing point and set zigzag
sewing.
54
Click the “Special Stitch” button to enter Hitch/Zigzag sewing set interface on the main interface.
Parameter Description:
[Same width]: tick in the small boxin front of the option, you can set the transverse stitch
length of zigzag stitching to be aequilate. Or cancel this tick in front of the option to set the left
and right width value.
55
[Width]: transverse stitch length, when zigzag stitching is set to be aequilate, set the width of
zigzag stitching. Value range is from 0.5 mm to 20 mm (0.1 mm as the incremental unit)
[Left width]: left transverse stitch length, when zigzag stitching is not set to be aequilate, set
left width.
[Right width]: right transverse stitch length, when zigzag stitching is not set to be aequilate,
set right width.
[Hitch Span]: used to set the span of zigzag stitching.
[needle number of up-down]: set the number of threads from one tip to the next tip of
zigzag stitching, values of 2, 3, 4,5,6.
[Zigzag sew shape]: used to generate stitch data. Select shape of zigzag stitching, V and N
shape available.
Zigzag sewing of N shape
56

(En) M Sew - Soft Instruction

Uploaded by

Copyright:

Available Formats

(En) M Sew - Soft Instruction

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

(En) M Sew - Soft Instruction

Uploaded by

Copyright:

Available Formats

M A u tom a tic S e w i n g Contr ol Sy s te m

Automatic Sewing Control

M A u tom a tic S e w i n g Contr ol Sy s te m

1.1 Software installation process

Click next step:

Pop up all the configuration option parameters, then click “install”:

1.2 Software uninstall process

2. Basic use of the software

2.1 Graphic illustration of each place of the main interface:：

Shape scope Layer color

2.2 Open and save the documents

No. Icon Shortcut key Name Functions and contents

Open the Click this button to open the pattern

2.3 Operation instructions of the basic keys on the main interface

No. Icon Shortcut key Name

3 zoom in Click this button to zoom in the picture

Click this button to zoom out the

Show the related helping information of

To set different rotation angles, press

Graph Click this button to delete the selected

Set the moving distance in the “moving

Click this button to change a certain

2.4 Operation introductions of the graphical interface

2.4.1 Instructions of the graph operations

No. Operation instructions Functions and contents

You zoom in the graph with the current mouse position

2.4.2 Right-click pop-up pull-down menu

a) Select the graph, right click, it pops up:

b) Select the current sewing point then have right click:：

Instructions of the pop-up menu:

No. Operation names Functions and contents

2.5 Fast sorting of the main interface graphs

（1） Click the selected graph 7 as the beginning graph of sorting.

There are to ways to pop up the dialog box of “layer change”

4. Copy of the current graph

No. Operation name Functions and contents

Copy the whole layer, the operation object is the

5. Modify the current graph

Interface of modifying the current graph

5.1. Adding points

（2）Disassemble the graphs

Disassemble the current graph into 2 graphs

5.3. Special sewing

（2）Choose the starting point of the special sewing.

（3）Choose the end point of the special sewing.

（4）Touch the button “local special sewing”.

2. Special sewing of the graphs

（3）Touch the key “special graph sewing”

3. Cancel the special sewing

Batch processing interface

6.3 Horizontal mirroring

Y direction is central mirroring

6.4 Vertical mirroring

6.6 Left-right sorting

Before left-right sorting

After left-right sorting

6.7 Top starting point

Before the operation of top starting point

After the operation of top starting point