®

Desmocoll XP 2597/4

Characterization Predominantly linear hydroxyl polyurethane.

®
Desmocoll XP 2597/4 is a flexible polyurethane with a high rate of
crystallization and low thermoplasticity. It has good adhesion on many flexible
PVC substrates.
Form supplied Granules

Specification
Property Value Unit of measurement Method
Solution viscosity, 15 % in 1,500 - 2,200 mPa·s DIN EN ISO 3219/A.3
butanone-2 (MEK)
at 23 °C, Haake

Other data*
Property Value Unit of measurement Method
Hydroxyl content < 0.1 % DIN 53 240
Density approx. 1.2 g/ml DIN EN ISO 2811
Crystallization approx. 50 min. DIN 53 505
Minimum activation temperature approx. 45 °C DIN EN 12961
Hot tack life approx. 6 min DIN EN 12961
Heat resistance approx. 75 °C ASTM D 816
Bondability of materials containing very good DIN EN 15307
plasticisers
*These values provide general information and are not part of the product specification.

page 1 of 3
Edition 2022-11-28

Replaces edition dated 2015-09-01 Product Datasheet

 ®
Desmocoll XP 2597/4

Appearance of solution (visual) clear; depending on storage time, storage conditions and formulation,
yellowing may occur
Solubility (visual) butanone-2 soluble (moderate viscosity increase over time)
acetone soluble (moderate viscosity increase over time)
ethyl acetate insoluble
acetone/toluene (2 : 1) soluble (significant viscosity increase over time)
MEK/ethyl acetate (1 : 1) insoluble
Properties / Applications ®
Desmocoll XP 2597/4 is suitable for the formulation of adhesives for use
on various materials, e.g. leather, rubber, textiles, wood, various plastics
(including polyurethane elastomers), plastic films and aluminum foils.
Disposal Please pay attention to the current safety data sheet.
Packaging Paper sacks of 25 kg, 30 sacks on a pallet of 750 kg
Storage - Storage in original sealed Covestro containers.

- Recommended storage temperature: 10 - 25 °C.

- Protect from direct sunlight, moisture, heat and foreign material.

Storage time Covestro represents that, for a period of six months following the day
of shipment as stated in the respective transport documents, the product
will meet the specifications or values set forth in section "specifications or
characteristic data" above, what ever is applicable, provided that the product is
stored in full compliance with the storage conditions set forth in and referenced
under section "storage" above and is otherwise handled appropriately.
The lapse of the six months period does not necessarily mean that the product
no longer meets specifications or the set values. However, prior to using said
product, Covestro recommends to test such a product if it still meets the
specifications or the set values. Covestro does not make any representation
regarding the product after the lapse of the six months period and Bayer
MaterialScience shall not be responsible or liable in any way for the product
failing to meet specifications or the set values after the lapse of the six months
period.

page 2 of 3
Edition 2022-11-28

Replaces edition dated 2015-09-01 Product Datasheet

 ®
Desmocoll XP 2597/4

Labeling and statutory requirements This product data sheet is only valid in conjunction with the latest edition of the
corresponding Safety Data Sheet. Any updating of safety-relevant information
– in accordance with statutory requirements – will only be reflected in the Safety
Data Sheet, copies of which will be revised and distributed. Information relating
to the current classification and labeling, applications and processing methods
and further data relevant to safety can be found in the currently valid Safety
Data Sheet.

The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal,
written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is
imperative that you test our products, technical assistance, information and recommendations to determine to your own satisfaction whether our
products, technical assistance and information are suitable for your intended uses and applications. This application-specific analysis must at least
include testing to determine suitability from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been
done by Covestro. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which
are available upon request. All information and technical assistance is given without warranty or guarantee and is subject to change without notice.
It is expressly understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in
connection with the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized
and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to
any material or its use. No license is implied or in fact granted under the claims of any patent.
This product is not designated for the manufacture of a medical device or of intermediate products for medical devices1). [This product is also not
designated for other specifically regulated applications (e.g. including cosmetics, plant protection, fertilisers, plant strengtheners, food processing, food
contact and others). If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices or
for other specifically regulated applications Covestro must be contacted in advance to provide its agreement to sell such product for such purpose.]
Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food
Contact products or cosmetic applications must be made solely by the purchaser of the product without relying upon any representations by Covestro.
1) Please see the "Guidance on Use of Covestro Products in a Medical Application" document.
Edition: January, 2018
Editor: Coatings, Adhesives & Specialties
Covestro Deutschland AG
Kaiser-Wilhelm-Allee 60 Contact:
51373 Leverkusen,Germany CAS Single Point of Contact EMEA
www.covestro.com e-mail: [email protected]
page 3 of 3
Edition 2022-11-28

Replaces edition dated 2015-09-01 Product Datasheet