Conforms to WHMIS 2015, Canadian Hazardous Products Regulation (HPR)

SAFETY DATA SHEET

Barrier 80 S Comp A
Section 1. Identification
Product identifier : Barrier 80 S Comp A
Product code : 37942
Product description : Paint.
Other means of : Not available.
identification
Product type : Liquid.

Supplier's details : Jotun Paints, Inc.

9203 Highway 23
Belle Chasse, LA 70037
Telephone: (800) 229-3538 or
+1 504-394-3538
[email protected]

Emergency telephone : 1-800-424-9300

number (with hours of (Staffed 24/7)
operation)
37942;37943 1 37942 ^(ValidationDate) 1

Approved

Section 2. Hazard identification

Classification of the : FLAMMABLE LIQUIDS - Category 3
substance or mixture SKIN IRRITATION - Category 2
EYE IRRITATION - Category 2A
SKIN SENSITIZATION - Category 1
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
AQUATIC HAZARD (ACUTE) - Category 1
AQUATIC HAZARD (LONG-TERM) - Category 1

GHS label elements

Hazard pictograms :

Signal word : Warning.

Hazard statements : Flammable liquid and vapor.
Causes skin irritation.
May cause an allergic skin reaction.
Causes serious eye irritation.
May cause damage to organs through prolonged or repeated exposure. (hearing
organs)
Very toxic to aquatic life with long lasting effects.
Precautionary statements
Prevention : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot
surfaces, sparks, open flames and other ignition sources. No smoking. Avoid
release to the environment. Do not breathe vapor or spray.

Date of issue : 03.08.2021 1/12

Barrier 80 S Comp A

Section 2. Hazard identification

Response : Collect spillage. Get medical advice or attention if you feel unwell. Take off
contaminated clothing and wash it before reuse. IF ON SKIN: Wash with plenty of
water. If skin irritation or rash occurs: Get medical advice or attention. IF IN EYES:
Rinse cautiously with water for several minutes. Remove contact lenses, if present
and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or
attention.
Storage : Not applicable.
Disposal : Dispose of contents and container in accordance with all local, regional, national
and international regulations.

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of : Not available.
identification

CAS number/other identifiers

CAS number : Not applicable.
Product code : 37942
Ingredient name % CAS number
zinc 65 - 85 7440-66-6
xylene 3-7 1330-20-7
epoxy resin (MW 700-1200) 1-5 25036-25-3
ethylbenzene 1-5 100-41-4
glycidyl ether of 3-alkyl phenol 0.1 - 1 68413-24-1
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First-aid measures

Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
If not breathing, if breathing is irregular or if respiratory arrest occurs, provide
artificial respiration or oxygen by trained personnel. It may be dangerous to the
person providing aid to give mouth-to-mouth resuscitation. Get medical attention
following exposure or if feeling unwell. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight
clothing such as a collar, tie, belt or waistband.
Skin contact : Wash with plenty of soap and water. Remove contaminated clothing and shoes.
Wash contaminated clothing thoroughly with water before removing it, or wear
gloves. Continue to rinse for at least 10 minutes. Get medical attention. In the
event of any complaints or symptoms, avoid further exposure. Wash clothing
before reuse. Clean shoes thoroughly before reuse.
Ingestion : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air
and keep at rest in a position comfortable for breathing. If material has been
swallowed and the exposed person is conscious, give small quantities of water to
drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs,
the head should be kept low so that vomit does not enter the lungs. Get medical
attention following exposure or if feeling unwell. Never give anything by mouth to an
unconscious person. If unconscious, place in recovery position and get medical
attention immediately. Maintain an open airway. Loosen tight clothing such as a

Date of issue : 03.08.2021 2/12

Barrier 80 S Comp A

Section 4. First-aid measures

collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : Causes serious eye irritation.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain or irritation
watering
redness
Inhalation : No specific data.
Skin contact : Adverse symptoms may include the following:
irritation
redness
Ingestion : No specific data.

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Wash contaminated clothing thoroughly with water before removing it, or wear
gloves.

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media
Unsuitable extinguishing : Do not use water jet.
media

Specific hazards arising : Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard.
from the chemical In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion. This material is very toxic to aquatic life with
long lasting effects. Fire water contaminated with this material must be contained
and prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
metal oxide/oxides

Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without
suitable training. Move containers from fire area if this can be done without risk.
Use water spray to keep fire-exposed containers cool.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Date of issue : 03.08.2021 3/12

Barrier 80 S Comp A

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialized clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways,
drains and sewers. Inform the relevant authorities if the product has caused
environmental pollution (sewers, waterways, soil or air). Water polluting material.
May be harmful to the environment if released in large quantities. Collect spillage.

Methods and materials for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble.
Alternatively, or if water-insoluble, absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a licensed waste disposal
contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an
effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
and place in container for disposal according to local regulations (see Section 13).
Dispose of via a licensed waste disposal contractor. Contaminated absorbent
material may pose the same hazard as the spilled product. Note: see Section 1 for
emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in
which this product is used. Do not get in eyes or on skin or clothing. Do not breathe
vapor or mist. Do not ingest. Avoid release to the environment. Use only with
adequate ventilation. Wear appropriate respirator when ventilation is inadequate.
Do not enter storage areas and confined spaces unless adequately ventilated. Keep
in the original container or an approved alternative made from a compatible material,
kept tightly closed when not in use. Store and use away from heat, sparks, open
flame or any other ignition source. Use explosion-proof electrical (ventilating,
lighting and material handling) equipment. Use only non-sparking tools. Take
precautionary measures against electrostatic discharges. Empty containers retain
product residue and can be hazardous. Do not reuse container.
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.

Date of issue : 03.08.2021 4/12

Barrier 80 S Comp A

Section 7. Handling and storage

Conditions for safe storage, : Store in accordance with local regulations. Store in a segregated and approved
including any area. Store in original container protected from direct sunlight in a dry, cool and well-
incompatibilities ventilated area, away from incompatible materials (see Section 10) and food and
drink. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not
store in unlabeled containers. Use appropriate containment to avoid environmental
contamination. See Section 10 for incompatible materials before handling or use.

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
xylene CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 100 ppm 8 hours.
15 min OEL: 651 mg/m³ 15 minutes.
15 min OEL: 150 ppm 15 minutes.
8 hrs OEL: 434 mg/m³ 8 hours.
CA British Columbia Provincial (Canada,
1/2020).
TWA: 100 ppm 8 hours.
STEL: 150 ppm 15 minutes.
CA Quebec Provincial (Canada, 7/2019).
TWAEV: 100 ppm 8 hours.
TWAEV: 434 mg/m³ 8 hours.
STEV: 150 ppm 15 minutes.
STEV: 651 mg/m³ 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
STEL: 150 ppm 15 minutes.
TWA: 100 ppm 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 150 ppm 15 minutes.
TWA: 100 ppm 8 hours.
ethylbenzene CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 100 ppm 8 hours.
8 hrs OEL: 434 mg/m³ 8 hours.
15 min OEL: 543 mg/m³ 15 minutes.
15 min OEL: 125 ppm 15 minutes.
CA British Columbia Provincial (Canada,
1/2020).
TWA: 20 ppm 8 hours.
CA Ontario Provincial (Canada, 6/2019).
TWA: 20 ppm 8 hours.
CA Quebec Provincial (Canada, 7/2019).
TWAEV: 100 ppm 8 hours.
TWAEV: 434 mg/m³ 8 hours.
STEV: 125 ppm 15 minutes.
STEV: 543 mg/m³ 15 minutes.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 125 ppm 15 minutes.
TWA: 100 ppm 8 hours.

Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust
controls ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapor or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Date of issue : 03.08.2021 5/12
Barrier 80 S Comp A

Section 8. Exposure controls/personal protection

Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn,
unless the assessment indicates a higher degree of protection: chemical splash
goggles.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.
There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.
Wear suitable gloves tested to EN374.
Not recommended, gloves(breakthrough time) < 1 hour: neoprene, butyl rubber
May be used, gloves(breakthrough time) 4 - 8 hours: PVC
Recommended, gloves(breakthrough time) > 8 hours: nitrile rubber, 4H, Teflon,
polyvinyl alcohol (PVA)

Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.

Date of issue : 03.08.2021 6/12

Barrier 80 S Comp A

Section 9. Physical and chemical properties

Appearance
Physical state : Liquid.
Color : Grey
Odor : Characteristic.
Odor threshold : Not available.
pH : Not applicable.
Melting point : Not available.
Boiling point : Lowest known value: 120.17°C (248.3°F) (1-methoxy-2-propanol). Weighted
average: 131.72°C (269.1°F)
Flash point : Closed cup: 25°C (77°F)
Evaporation rate : Not available.
Flammability (solid, gas) : Not available.
Lower and upper explosive : Not available.
(flammable) limits
Vapor pressure : Not available.
Vapor density : Not available.
Relative density : 2.574 g/cm³ @ 20 °C 21.48 pounds/gallon @ 20 °C
Solubility : Insoluble in the following materials: cold water and hot water.
Partition coefficient: n- : Not available.
octanol/water
Auto-ignition temperature : Not available.
Decomposition temperature : Not available.
Viscosity : Kinematic (40°C (104°F)): >0.205 cm2/s (>20.5 mm2/s)

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Chemical stability : The product is stable.

Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions

Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.

Incompatible materials : Reactive or incompatible with the following materials:

oxidizing materials

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
xylene LC50 Inhalation Vapor Rat 20 mg/l 4 hours
LD50 Oral Rat 4300 mg/kg -
TDLo Dermal Rabbit 4300 mg/kg -
ethylbenzene LC50 Inhalation Vapor Rat - Male 17.8 mg/l 4 hours
LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -

Date of issue : 03.08.2021 7/12

Barrier 80 S Comp A

Section 11. Toxicological information

Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
zinc Skin - Mild irritant Human - 72 hours 300 -
Micrograms
Intermittent
xylene Eyes - Mild irritant Rabbit - 87 milligrams -
Skin - Mild irritant Rat - 8 hours 60 -
microliters
epoxy resin (MW 700-1200) Skin - Mild irritant Mammal - - - -
species
unspecified
Eyes - Mild irritant Mammal - - - -
species
unspecified
Sensitization
Product/ingredient name Route of Species Result
exposure
epoxy resin (MW 700-1200) skin Mammal - species Sensitizing
unspecified
glycidyl ether of 3-alkyl skin Mammal - species Sensitizing
phenol unspecified
Mutagenicity
Not available.
Carcinogenicity
Not available.
Reproductive toxicity
Not available.
Teratogenicity
Not available.
Specific target organ toxicity (single exposure)
Name Category Route of Target organs
exposure
xylene Category 3 - Respiratory tract
irritation
Specific target organ toxicity (repeated exposure)
Name Category Route of Target organs
exposure
ethylbenzene Category 2 - hearing organs

Aspiration hazard
Name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1

Information on the likely : Not available.

routes of exposure
Potential acute health effects
Eye contact : Causes serious eye irritation.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.

Date of issue : 03.08.2021 8/12

Barrier 80 S Comp A

Section 11. Toxicological information

Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Eye contact : Adverse symptoms may include the following:
pain or irritation
watering
redness
Inhalation : No specific data.
Skin contact : Adverse symptoms may include the following:
irritation
redness
Ingestion : No specific data.

Delayed and immediate effects and also chronic effects from short and long term exposure
Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Potential chronic health effects
Not available.
General : May cause damage to organs through prolonged or repeated exposure. Once
sensitized, a severe allergic reaction may occur when subsequently exposed to very
low levels.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.

Numerical measures of toxicity

Acute toxicity estimates
Route ATE value
Dermal 20404.95 mg/kg
Inhalation (vapors) 269.91 mg/l

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
zinc Acute LC50 330 µg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 0.78 mg/l Fresh water Fish 96 hours
ethylbenzene Acute EC50 7.2 mg/l Algae 48 hours
Acute EC50 2.93 mg/l Daphnia 48 hours
Acute LC50 4.2 mg/l Fish 96 hours

Persistence and degradability

Date of issue : 03.08.2021 9/12

Barrier 80 S Comp A

Section 12. Ecological information

Product/ingredient name Aquatic half-life Photolysis Biodegradability
zinc - - Not readily
xylene - - Readily
ethylbenzene - - Readily

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
xylene 3.12 8.1 to 25.9 low
ethylbenzene 3.6 - low

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimized wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction. Waste packaging should be recycled. Incineration or
landfill should only be considered when recycling is not feasible. This material and
its container must be disposed of in a safe way. Care should be taken when
handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Vapor from product residues
may create a highly flammable or explosive atmosphere inside the container. Do
not cut, weld or grind used containers unless they have been cleaned thoroughly
internally. Avoid dispersal of spilled material and runoff and contact with soil,
waterways, drains and sewers.
Do not allow to enter drains or watercourses. Material and/or container must be disposed of as hazardous waste.

Section 14. Transport information

TDG DOT ADR/RID IMDG IATA
Classification Classification
UN number UN1263 UN1263 UN1263 UN1263 UN1263

UN proper Paint Paint Paint Paint Paint

shipping name
Transport 3 3 3 3 3
hazard class(es)

Packing group III III III III III

Date of issue : 03.08.2021 10/12

Barrier 80 S Comp A

Section 14. Transport information

Environmental Yes. Yes. Yes. Yes. Yes. The
hazards environmentally
hazardous
substance mark
is not required.

Additional information
TDG Classification : Product classified as per the following sections of the Transportation of Dangerous
Goods Regulations: 2.18-2.19 (Class 3), 2.7 (Marine pollutant mark).
The marine pollutant mark is not required when transported by road or rail.
DOT Classification : This product is not regulated as a marine pollutant when transported on inland
waterways in sizes of ≤5 L or ≤5 kg or by road, rail, or inland air in non-bulk sizes,
provided the packagings meet the general provisions of §§ 173.24 and 173.24a.
Reportable quantity 1394.7 lbs / 633.19 kg [64.985 gal / 245.99 L]. Package sizes
shipped in quantities less than the product reportable quantity are not subject to the
RQ (reportable quantity) transportation requirements.
ADR/RID : Tunnel restriction code: (D/E)
Hazard identification number: 30
IMDG : Emergency schedules (EmS): F-E, S-E
Marine pollutant: Yes.
IATA : The environmentally hazardous substance mark may appear if required by other
transportation regulations.
Marking : The environmental hazardous / marine pollutant mark is only applicable for
packages containing more than 5 litres for liquids and 5 kg for solids.

Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.

Transport in bulk according : Not available.

to IMO instruments

Section 15. Regulatory information

Canadian lists
Canadian NPRI : The following components are listed: zinc (and its compounds); zinc (and its
compounds); xylene (all isomers); ethylbenzene; other glycol ethers and acetates
(and their isomers)
CEPA Toxic substances : None of the components are listed.
Canada inventory : Not determined.
International regulations
Chemical Weapon Convention List Schedules I, II & III Chemicals
Not listed.
Montreal Protocol
Not listed.
Stockholm Convention on Persistent Organic Pollutants
Not listed.
UNECE Aarhus Protocol on POPs and Heavy Metals
Not listed.
Inventory list
Australia : Not determined.
China : Not determined.
Europe : At least one component is not listed.

Date of issue : 03.08.2021 11/12

Barrier 80 S Comp A

Section 15. Regulatory information

Japan : Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Malaysia : Not determined
New Zealand : Not determined.
Philippines : Not determined.
Republic of Korea : Not determined.
Taiwan : Not determined.
Turkey : Not determined.
United States : Not determined.

Section 16. Other information

History
Date of printing : 03.08.2021
Date of issue/Date of : 03.08.2021
revision
Date of previous issue : 16.07.2019
Version : 1.02
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
HPR = Hazardous Products Regulations
Procedure used to derive the classification
Classification Justification
FLAMMABLE LIQUIDS - Category 3 On basis of test data
SKIN IRRITATION - Category 2 Calculation method
EYE IRRITATION - Category 2A Calculation method
SKIN SENSITIZATION - Category 1 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED Calculation method
EXPOSURE) - Category 2
AQUATIC HAZARD (ACUTE) - Category 1 Calculation method
AQUATIC HAZARD (LONG-TERM) - Category 1 Calculation method
References : Not available.
Indicates information that has changed from previously issued version.
Notice to reader
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are
often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the
product itself. Minor product variations may be implemented in order to comply with local requirements.
Jotun reserves the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their
needs and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United
Kingdom) version will prevail.

Date of issue : 03.08.2021 12/12