This document contains an exam for the subjects of Engineering Graphics and Design. It has 5 questions covering topics like scales, mechanisms, projections, developments and isometric drawings. The exam contains both 2D and 3D problems to be solved visually based on given dimensions and requirements. Students are instructed to attempt all questions and use assumptions where needed.
This document contains an exam for the subjects of Engineering Graphics and Design. It has 5 questions covering topics like scales, mechanisms, projections, developments and isometric drawings. The exam contains both 2D and 3D problems to be solved visually based on given dimensions and requirements. Students are instructed to attempt all questions and use assumptions where needed.
This document contains an exam for the subjects of Engineering Graphics and Design. It has 5 questions covering topics like scales, mechanisms, projections, developments and isometric drawings. The exam contains both 2D and 3D problems to be solved visually based on given dimensions and requirements. Students are instructed to attempt all questions and use assumptions where needed.
This document contains an exam for the subjects of Engineering Graphics and Design. It has 5 questions covering topics like scales, mechanisms, projections, developments and isometric drawings. The exam contains both 2D and 3D problems to be solved visually based on given dimensions and requirements. Students are instructed to attempt all questions and use assumptions where needed.
BE - SEMESTER–I & II(NEW) EXAMINATION – WINTER 2022 Subject Code:3110013 Date:10-03-2023 Subject Name:Engineering Graphics & Design Time:10:30 AM TO 01:30 PM Total Marks:70 Instructions: 1. Attempt all questions. 2. Make suitable assumptions wherever necessary. 3. Figures to the right indicate full marks. 4. Simple and non-programmable scientific calculators are allowed. Marks Q.1 (a) Define representative fraction (R.F.) of scale. Also list types of scale 03 according to value of R.F. (b) In a slider crank mechanism OBA, the crank OB is 200 mm long and the 04 connecting rod BA is 850 mm long. Plot the locus of point P where P is midpoint of connecting rod. Refer figure 1. (c) Construct one complete turn of an involute of a circle having diameter 30 07 mm. Also draw tangent and normal to the curve S. The point S is a point on the involute and it is at a distance of 45mm from centre of the circle.
Q.2 (a) Draw the projection of following points on the same X-Y line. 03 (1) Point A is 20 mm above HP and 30 mm behind V.P. (2) Point B is on HP and 40 mm in front of V.P. (3) Point C is 10 mm bellow HP and 25 mm behind V.P. (b) A line MN, 60 mm long, is in V.P. It makes an angle of 30° with the H.P. 04 The end point M is 15 mm above H.P. Draw projections of line MN. Also measure Plan length of the line. (c) The line AB has its end A, 15 mm above H.P. and 10 mm in front of V.P. 07 The end B is 60 mm above H.P. The distance between the end projectors is 50 mm. The plan of the line is inclined at 25° to X-Y line. Draw the projections of line. Find true length and inclination of the line with H.P. OR (c) Draw the projections of a straight line 80 mm long inclined at 60° to H.P. 07 and 30° to V.P. with end A in the H.P. and the end B in the V.P.
Q.3 (a) A pentagonal plate, side 25 mm, is inclined to H.P. by 30°.It is 03
perpendicular to V.P. and resting on HP on its one of the side. Draw projections of the plate. (b) A circular disk, 50 mm in diameter, is resting on the H.P. on one of the 04 point A of the circumference. Plane is inclined to the H.P. such a way that the top view of it is an ellipse of minor axis 40 mm. Draw its projections. (c) A cone, base diameter 30 mm and height 60 mm, is resting on its base. It 07 is cut by AIP inclined at 45°to H.P. and passing through midpoint of the axis of cone. Draw front view, sectional top view and true shape of this sectional solid. OR Q.3 (a) A hexagonal plate, side 25 mm, is inclined to H.P. by 45°. It is resting on 03 HP on one of the corner. The plate is perpendicular to V.P. Draw projections of the plate.
1 (b) A square plate, 40 mm side, is resting on the H.P. on one of its sides. The 04 plate is inclined to H.P such a way that it’s top view looks like a rectangle with 20 mm shorter side. Draw its projections. (c) A square prism, side of base 30 mm and height 45 mm, is resting on H.P. 07 on one of the corners of the base. The longer edge containing that corner on which it rests, is inclined at 45° to H.P. and top view of it is inclined at 30° to V.P. Draw the projections when top end of the prism is nearer to V.P.
Q.4 (a) Develop the complete surface of a square prism of side of base 40 mm 03 and height 80 mm. (b) Draw front view of an object shown in figure 2 using first angle projection 04 methods. (c) Draw top view and left hand side view of object shown in figure 2 using 07 first angle projection methods. OR Q.4 (a) Draw the development of the lateral surface of a square pyramid, side of 03 base 30 mm and height 50 mm, resting with its base on H.P. All edge of the base are equally inclined to V.P. (b) Draw front view of an object shown in figure 3 using first angle projection 04 methods. (c) Draw top view and left hand side view of object shown in figure 3 using 07 first angle projection methods.
Q.5 (a) Explain any three AutoCAD commands in short 03
(1) Spline (2) Rotate (3) Polygon (4) Multiline (b) Draw isometric scale showing 100 mm isometric length equivalent to 04 100mm normal length. (c) Draw isometric projection of an object whose front view and top view are 07 shown in figure 4. OR Q.5 (a) Explain any three AutoCAD commands in short. 03 (1) Circle (2) Array (3) Mirror (4) Filet Command (b) Draw isometric shape of a circle having 60 mm in diameter using four 04 centre methods. (c) Draw isometric projection of an object whose front view, top view and 07 side view are shown in figure 5.
