Chapter 2 DC Analysis

Basic Electricity and Electronics-PCE-2103 A/Y-2016/17
---------------------------------------------------------------------------------------------------------------------
CHAPTER TWO
Circuit Analysis Techniques

-------------------------------------------------------------------------------------------------------------------------------
Basic circuit laws and rules
Ohm's Law
Ohm's Law states that the current in an electric circuit is directly proportional to the applied voltage and
inversely proportional to the resistance of the circuit. Three forms of Ohm's Law equations are: I=V/R,
V=IR and R=V/I . Therefore Ohm's Law can be used for finding current, voltage drop and resistance in a
circuit.
Basic DC electric circuits

Depending on their source of electrical energy, there are two types of electric circuit.
1. Dc electric Circuit - is the one with Dc source.
2. Ac electric circuit- is the one with an Ac source.
Depending on connection of devices, basically there are three types of circuits:-
1. Series connection
2. Parallel connection
3. Series-Parallel connection
Series circuit
Series Circuit:-In series circuit elements are connected end to end.
There is the same current flowing through all the elements.
The total resistance is the sum of the individual resistances.
The applied voltage is the sum of all the voltage drops.
R1 R2
I
+ VR 1 - + VR 2 -
+
Vs VR N RN
-
- VR 3 +
R3
Fig. 1 series circuit
Mathematically,
1
RT = R1 + R2 + R3 +……….+RN
Vs = VR1 + VR2 + VR3+…..…+RN
Is = IR1 = IR2 = IR3 =………….=IRN
Voltage Divider Rule
States that the amount of voltage drops across each element is directly proportional to the source voltage
and resistance value
Vs R1
. VR 1   R 1  R1  Vs
RT RT
Vs R2
VR 2   R 2  R2  Vs
RT RT
Vs R3
VR 3   R 3  R3  Vs
RT RT
Parallel circuits
Two or more components which are connected to common nodes are said to have a parallel connection.
Parallel circuit:-In a simple parallel circuit
The voltage across each element is the same.
The total current is the sum of the individual branch currents.
IT
I1 I2 I3
Vs R1 R2 RN
Fig. 2 parallel circuit
Mathematically,
1 1 1 1
   ....... 
RT R1 R2 RN
Vs = VR1 = VR2 = VR3=………..= VRN
Is = IR1 + IR2 + IR3 =…………. =IRN
Current Divider Rule

2
States that the amount of current flow through each element is directly proportional to the total current
and inversely proportional to the resistance value
R1
R2 I2  T
I1  T R 1  R2
R 1  R2
Series-Parallel circuits
Series- Parallel circuit is a combination of both series and parallel circuits. Therefore it has the property
of both series and parallel circuit.
Example for the circuit below calculate total resistor and current flow through each elements If
R1=6K , R2=12K, R3=4K, R4=8K, R5=12K
Solution In calculating the required parameters always we have to start from the outer to the source
Thus , R3 +R4 = 4K+8k =12k................R34
R2//R34 = 12k//12k =6k................R234
R234 + R1 = 6k+6k = 12k...........R1234
R1234//R5 = 12k//12k = 6k.................total resistor
Using ohms law, IT =Vs/RT = 24V/6k =4mA ......Total curent
Using CDR
3
= 2mA......curent across R5 and also across R 1234
Again I1 is further sub divided in to I6 and I2. To find curent across I6 and I2 apply CDR finaly you will
got 1mA each.
Kirchhoff’s Current and voltage Laws
Kirchhoff's Current Law (KCL)
It states that the algebraic sum of the currents entering and leaving any junction is zero. In other words,
the sum of the currents entering a point is always equal to the sum of the currents leaving.
I2 I4
I1 I5
I3 I6
Mathematically,
S I entering a node = S I leaving a node
From the above diagram currents I1, I4, I6 are currents entering the node and I2, I3, I5 are currents
leaving the node Thus
I2 + I3 + I5 = I1 +I4 + I6
Kirchhoff's Voltage Law (KVL)
It states that the algebraic sum of voltages in a closed loop is zero. In other words the sum the supply
voltage in a closed loop is always equal to the sum of the voltage drops
R1 R2
I
+ V1 - + V2 - +
Vs V3 R3
-
Mathematically,
In a closed loop = 0
4
From the above circuit
Vs – V1 – V2 – V3 = 0
or -Vs+ V1+ V2+ V3 = 0
Vs = V1 + V2 + V3
Mesh (loop) and Nodal Analysis

Mesh (loop) Analysis
Mesh analysis provides a general procedure for analyzing circuits, using mesh currents as the circuit
variables. Using mesh currents instead of element currents as circuit variables is convenient and reduces
the number of equations that must be solved simultaneously.
A loop is a closed path with no node passed more than once. A mesh is a loop that does not contain any
other loop within it. Mesh analysis applies KVL to find unknown currents.
Steps to determine mesh currents
1. Assign mesh currents i1, i2. . . in to the n meshes.
2. Apply KVL to each of the n meshes. Use Ohm’s law to express the voltages in terms of the mesh
currents.
3. Solve the resulting n simultaneous equations to get the mesh currents.
Example:Find Vo?
Solution:
We have 3 meshes (loops)
KVL left loop :
5
KVL middle loop :
KVL right loop :
Solve the above three equations involving the variables i 1, i2 and i3 using simaltaneous solving
method. In matrix form the equations can be expressed as
Solving the matrix we can find that
Nodal Analysis
Nodal analysis provides a general procedure for analyzing circuits using node voltages as the circuit
variables. Choosing node voltages instead of element voltages as circuit variables is convenient and
reduces the number of equations one must solve simultaneously. In nodal analysis, we are interested in
finding the node voltages.
Steps to determine node voltages:
1. Select a node as the reference node. Assign voltages v1, v2, . . . , vn−1 to the remaining n −1 nodes. The
voltages are referenced with respect to the reference node.
2. Apply KCL to each of the n −1 nonreference nodes. Use Ohm’s law to express the branch currents in
terms of node voltages.
3. Solve the resulting simultaneous equations to obtain the unknown node voltages.
4. Find the actually voltage and / or current

The first step in nodal analysis is selecting a node as the reference or datum node. The reference node is
commonly called the ground sinceit is assumed to have zero potential. We then apply KCL at each node
applying Ohm’s law to express the unknown currents i1, i2, i3… in terms of node voltages.
The key idea to bear in mind when expressing the unknown currents in terms of node voltages is that,
Current flows from a higher potential to a lower potential in a resistor.
We can express this principle as
6
Example :- find the voltages at node 1 and 2
R3=
R1= R5=
2Ω
2Ω 1 2 1Ω
i1 i3 i5
Vm=10 V R2= R4=

Vn=
1Ω 2Ω
5V
i2 i4
3
Essential nodes are: 1,2,3
Consider node 3 to be the reference node(ground)
Applying KCL at node 1
Apply KCL at node 2,
Using the equations from the two nodes we can solve simultaneously or using matrixes
7
the start of the analysis.
2.5. Linearity and Superposition Theorem

Linearity
Linearity is the property of an element describing a linear relationship between cause and effect. It is a
combination of both homogeneity (scaling) property and the additivity property. The homogeneity
property requires that if input also called excitation is multiplied by a constant, then the output also called
the response is multiplied by the same constant. The additivity property requires that the response to a
sum of inputs is the sum of the responses to each input applied separately.
Mathematically, given a function , and & , the function is said to be linear if and only if for any two
inputs and and any constants and . This property of the function is said to be property of linearity.
Example: Is the power dissipated by a resistor a linear function of current?
Soln:
Therefore, the power dissipated in a resistor is not linear function of current. It can also be shown in the
same way that power dissipated in a resistor is not linear function of voltage.
Show that Ohm’s Law satisfies linearity property; Thus a resistor is a linear circuit element.
An electrical circuit is said to be linear if its outputs are linearly related (or directly proportional) to its
inputs. A linear circuit consists of only linear elements, linear dependent sources and independent
sources.
Superposition Theorem
If a circuit has two or more independent sources, the value of a specific variable can be determined by
adding the contribution of each independent source to the variable. This approach is known as
superposition and it is based on the property of linearity. This theorem can be stated as:
The current through or the voltage across an element in a linear network is equal to the algebraic sum of
the currents or the voltages produced independently by each source.
8
The effect of each source is considered independently by removing and replacing the other sources
without affecting the final result. To remove a voltage source when applying this theorem, the difference
in potential between the terminals of the voltage source must be set to zero (short circuit); removing a
current source requires that its terminals be opened (open circuit). The internal resistances associated with
the removed sources are not eliminated but must still be considered. This is illustrated in fig.2.5.
Fig.2.5 removing the effects of practical sources
As stated earlier, the total current through any portion of the circuit is equal to the algebraic sum of the
currents produced independently by each source. If the current produced by one source is in one direction,
while that produced by the other is in the opposite direction through the same resistor, the resulting
current is the difference of the two and has the direction of the larger. If the individual currents are in the
same direction, the resulting current is the sum of two in the direction of either current. This rule holds
true for the voltage across a portion of a circuit as determined by polarities, and it can be extended to
circuits with any number of sources. The superposition principle is not applicable to power effects since
the power loss in a resistor varies as the square (nonlinear) of the current or voltage, as proved previously.
Example: 1. In the circuit below, apply superposition theorem to find in terms of and .
Soln:
9
First find the contribution due to the source . This means the current source us turned off by making an
open circuit. This is shown below.
By VDR,
Now find the contribution due to the source .
By applying CDR and then Ohm’s Law, .

Therefore, by the superposition theorem, the voltage
Source transformation
A transformation that allow a voltage source in series with a resistor to be replaced by a current source in
parallel with the same resistor or vice versa.
IL
R a IL
+
+ IS R 10 VL RL
VS
VL RL
-
-
b
(a)(b)
Fig. 2.6 Circuits with Equivalent voltage source and current source with their respective resistance
connection
We need to find Is and Vs such that VL and IL is the same in both circuits
In ckt1 ,
In ckt2 ,
For IL to be the same, we need
V S
<=> IS R
Fig. 2.7 voltage sourcetransformed to current source
Where
Example : Use source transformation to find VO
11
1.6 Ω
60 V
20 Ω
36 A
+
VO 8Ω
120 V 6Ω
--
5Ω
Transform the two voltage sources in series with their respective resistances to current sources with
parallel resistance
1.6 Ω
120 / 20 60 / 5 36 A
20 Ω 5Ω +
=6A =12 A
VO 8Ω
6Ω
--
1.6 Ω
I2 R2
I1
i=36+6-12
= 30 A
R1 20//5//6 +
= 2.4Ω VO R3
--
Exersise : Using source transformation find the power associated with the 6 V source.
12
4Ω 6Ω 5Ω
40 V
6V
30 Ω 20 Ω
10 Ω
2.6. Thevenin’s and Norton’s Theorems

Before stating these two theorems, it is important to introduce the principle of source transformation.
Source transformation helps to simplify circuits. Its concept is based on the concept of equivalence. Two
circuits are equivalent if the voltage-current relationships are the same at their terminals.
A source transformation is the process of replacing a voltage source in series with a resistor R by a
current source in parallel with a resistor R, or vice versa. Fig. 2.8 shows the transformation. Note that the
arrow of the current source is directed toward the positive terminal of the voltage source. It can be shown
that for the two circuits to be equivalent, . Hence, source transformation requires that,
or
Fig. 2.8 Source transformation
Source transformation can also be applied to dependent sources provided that we carefully handle the
dependent variable.
13
Thevenin’s Theorem
It is often occurs in practice that a particular element in a circuit is variable (usually called load) while the
other elements are fixed. In this case, each time the variable element is changed, the entire circuit has to
be analyzed all over again. This problem can be avoided using Thevenin’s theorem that provides a
technique by which the fixed part of the circuit is replaced by an equivalent circuit.
Thevenin’s theorem states that any two-terminal linear circuit can be replaced by an equivalent circuit
consisting of a voltage source and a series resistor.
The box in fig. 2.9 (left side) contains a linear circuit having two terminals available to the outside world.
Using Thevenin’s theorem, it is possible to replace everything in the box with one source and a series
resistor as shown on the right, maintaining the same terminal characteristics. The circuit shown on the
right of Fig. 2.9 is called Thevenin’s equivalent circuit.
Fig. 2.9Replacing a linear two-terminal circuit by its Thevenin’s equivalent circuit
How to find the Thevenin’s equivalent voltage and resistance? Since the two circuits in Fig. 2.9 are
equivalent, they have the same voltage-current relationship at their terminals. This means, the open circuit
voltage of the linear circuit must be equal to the Thevenin’s voltage. Again since the two circuits are
equivalent, with all independent sources turned off, the input resistance at the terminals of the linear
circuit must be equal to.
To apply this idea in finding the Thevenin’s resistance, two cases can be considered. First if the linear
circuit has no dependent sources, then all independent sources are turned off and is the input resistance of
the circuit looking between the terminals. Second, if the linear circuit has dependent sources, all
independent sources are turned off. However, as with the superposition theorem, dependent sources are
not turned off because they are controlled by circuit variables. We apply a voltage source or current
source at the terminals and determine the resulting current or the voltage as shown in Fig. 2.10. Then .
14
Fig. 2.10Finding when circuit has dependent source
The following sequence of steps summarize how to obtain proper value of and.
1. Remove that portion of the circuit across which the Thevenin’s equivalent circuit is to be found.
This requires that the load resistor be temporarily removed from the circuit.
2. Calculate by first setting all independent sources to zero (voltage sources are replaced by short
circuits and current sources by open circuits) and then by finding the resultant resistance between
the two terminals. (If the internal resistance of the voltage and/or current sources is included in
the original network, it must remain when the sources are set to zero.). Use the method described
above if the circuit consists of dependent sources.
3. Calculate by first returning all independent sources to their original position and finding the
open-circuit voltage between the terminals.
4. Draw the Thevenin’s equivalent circuit with the portion of the circuit previously removed
replaced between the terminals of the equivalent circuit.
Norton’s Theorem
Norton’s theorem states that any linear circuit can be represented by an equivalent circuit, called Norton’s
Equivalent circuit, composed of a current source in parallel with a resistance. This theorem can be
obtained from Thevenin’s theorem by source transformation. Fig. 2.11 shows Norton’s equivalent circuit
obtained from the corresponding Thevenin’s equivalent circuit. Note that the Norton’s resistance R N is
equal to the Thevenin’s resistance RTh and the Norton’s current is the short circuit current between the
terminals where the load removed. It can also be obtained by dividing Thevenin’s voltage by Thevenin’s
resistance, as obvious from source transformation.
i.e.; and.
15
(a) Thevenin’s Equivalent circuit (b) Norton’s Equivalent circuit
Fig. 2.11 Obtaining Norton’s Equivalent circuit from Thevenin’s Equivalent circuit using
source transformation method
Examples:1. Use the Thevenin’s theorem to find Vo in the network below.
Soln:- Breaking the network at 4 kΩ load, the open circuit voltage can be obtained from the following
figure.
Writing mesh equation for loop I,
Then, the open circuit voltage Voc is obtained by writing KVL as follow for loop 2.
{No current flows in 2k Ω load }
RTh is derived from the following network.
16
RTh  2 K  (6K 3K)

 RTh  4 K
Therefore, Thevenin’s equivalent circuit is drawn below, attaching the load to it.
Finally using voltage division,
  6
 * 4 K   
VTh
Vo    * 4 K
 4 K   RTh   4 K   4 K  
 Vo   3V
2. Find Vo in the network below using Norton’s theorem.
Soln: In applying Norton’s theorem, we must find the short circuit current shown below.
17
The mesh equations for the above network are
12  9 I 1  6 I 2                                  1
I 2  I 3  4                                    2 
10 I sc  2 I 2  8 I 3  0                              3
Since there are four unknowns we need additional equation, and we can obtain it from KVL around
external loop.
12  3I 1  4 I 3                                  4 
Solving the above equations simultaneously, we obtain
I1  4mA
I 2  4mA
I 3  0mA and
4
I sc  mA
5
I sc is obtained. But to obtain Norton’s equivalent circuit, the Thevenin’s equivalent resistance has to be
obtained from the following network.
 RTh  3K 6 K  4 K  2 K  8 K 
6 * 10 6 * 10
 RTh  6 K 10 K   K
10  6 16
 RTh  15 k
4
Hence, the Norton’s equivalent circuit with the load connected is
18
4  15 
4 15
*
4
*4  
 vo  mA *  K 4 K   5 V
5 4  15  4
4
 12  48
  4V  V
 31  31
2.7. Maximum power transfer

We can determine the maximum power that a circuit can supply and a manner in which to adjust the load
to effect maximum power transfer by using Thevenin’s theorem.
Given the circuit shown below.
The power that is delivered to the load is given by the expression.
V
PL  i 2 RL but i
R  RL
2
 V 
 PL    RL
 R  RL 
We want to determine the value of R L that maximizes the power. Therefore, differentiating this expression
with respect to the load resistor R L, and equating the derivative to zero, we can obtain the value of R L for
which the power becomes maximized.
19
dp L V2 2 RL R  RL V 2
  0
dR L R  RL 2 R  RL 4
V 2
R  R  L
2
 2 RL R  RL   0
R  RL  4
 R  RL  2 RL  0
 RL  R
Therefore, maximum power transfer takes place when the load resistance R L= R. The voltage source V
and the resistance R could represent the voltage and the resistance in Thevenin’s equivalent circuit for
any linear network.
Then, the max power transferred is
 V  V2
PL max    R L 
 R  RL  R  RL
4RL
Examples: Find the value of R 2 for maximum power transfer in the network below and the maximum
power that can be transferred to this load.
Soln:- First obtain Thevenin’s equivalent circuit for the network exclusive of the load (resistor R 2).
Using mesh analysis to obtain VTh:
KVL across loop I3,
20
VTh  4 KI1  6 KI 2
but I 1  2mA and by KVL across loop I2,
6 KI 2  3V  3KI 2  I1   0
 6 KI 2  3V  3KI 2  3KI1  0
 9 KI 2  3K * 2mA  3V  3V
I 2  1 mA
3
VTh  4 K * 2mA  6 K * 1 mA
3
 8  2  10V
To obtain RTh consider the following circuit should be considered where the current source is turned off
by open circuiting, and the voltage source is turned off by short circuiting.
From the previous circuit
RTh  4 K  6 K 3K
6 K * 3 K
 4 K 
6 K  3 K
 RTh  6 K
Therefore, the Thevenin’s equivalent circuit is
21
For maximum power transfer RL =RTh.
 R L  RTh  6 K
Maximum power transferred to the load is

2 2
 Voc   10V 
PL    RL    * 6 K 
 RTh  R L   6 K  6 K 
10 2 25
 * 10 3 W  mW
4*6 6
22

Chapter 2 DC Analysis

Uploaded by

Copyright:

Available Formats

Chapter 2 DC Analysis

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 2 DC Analysis

Uploaded by

Copyright:

Available Formats

Basic Electricity and Electronics-PCE-2103 A/Y-2016/17

Circuit Analysis Techniques

Basic DC electric circuits

Vs = VR1 + VR2 + VR3+…..…+RN

Is = IR1 = IR2 = IR3 =………….=IRN

Voltage Divider Rule

Fig. 2 parallel circuit

Vs = VR1 = VR2 = VR3=………..= VRN

Is = IR1 + IR2 + IR3 =…………. =IRN

Current Divider Rule

Thus , R3 +R4 = 4K+8k =12k................R34

R2//R34 = 12k//12k =6k................R234

R234 + R1 = 6k+6k = 12k...........R1234

R1234//R5 = 12k//12k = 6k.................total resistor

Using ohms law, IT =Vs/RT = 24V/6k =4mA ......Total curent

= 2mA......curent across R5 and also across R 1234

Kirchhoff’s Current and voltage Laws

Kirchhoff's Current Law (KCL)

S I entering a node = S I leaving a node

Kirchhoff's Voltage Law (KVL)

From the above circuit

or -Vs+ V1+ V2+ V3 = 0

Mesh (loop) and Nodal Analysis

Steps to determine mesh currents

1. Assign mesh currents i1, i2. . . in to the n meshes.

3. Solve the resulting n simultaneous equations to get the mesh currents.

We have 3 meshes (loops)

KVL left loop :

KVL middle loop :

KVL right loop :

Solving the matrix we can find that

Steps to determine node voltages:

4. Find the actually voltage and / or current

We can express this principle as

Example :- find the voltages at node 1 and 2

Vm=10 V R2= R4=

Essential nodes are: 1,2,3

Consider node 3 to be the reference node(ground)

Applying KCL at node 1

Apply KCL at node 2,

the start of the analysis.

2.5. Linearity and Superposition Theorem

Example: Is the power dissipated by a resistor a linear function of current?

Fig.2.5 removing the effects of practical sources

By applying CDR and then Ohm’s Law, .

For IL to be the same, we need

Fig. 2.7 voltage sourcetransformed to current source

Example : Use source transformation to find VO

2.6. Thevenin’s and Norton’s Theorems

Fig. 2.8 Source transformation

Fig. 2.9Replacing a linear two-terminal circuit by its Thevenin’s equivalent circuit

Fig. 2.10Finding when circuit has dependent source

(a) Thevenin’s Equivalent circuit (b) Norton’s Equivalent circuit

Examples:1. Use the Thevenin’s theorem to find Vo in the network below.

Writing mesh equation for loop I,

{No current flows in 2k Ω load }

RTh is derived from the following network.

RTh  2 K  (6K 3K)