instructables

Raspberry Pi Pico 200Khz Digital Oscilloscope

by sainisagar7294

A Waveform analyzer, Signal generator and logic tester in a small PI PICO. With a dedicated application, Runs on Android.
Supplies:

Things needed for this projects:

1) Smart phone as display unit
2) Raspberry pi Pico
3) 1k, 100k resistors
4) Breadboard, jumper and usb wires
5) PCB and other soldering equipments* optional
6) OTG Jack

Step 1: Story:
Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 1
Hello everyone, Oscilloscope is mandatory for every electronics student or hobbyist. Keeping the budget in mind, I
suggest you use Mobile as an oscilloscope. But we can’t interface the signals directly to mobile phones. So here we are
using Raspberry pi Pico as the brain of this project. The signal from Pico goes to Mobile through USB to get a decent
waveform. Let’s make this project step by step.
Note** This project is only for educational purposes, and this Oscilloscope can measure small signals only. Not for
commercial purposes, just a project to know the capabilities of this board.

Step 2: Features of Oscilloscope:

200Khz bandwidth
2-channel supported
500KS/s sampling rate
Time/div: 5micro Second to 20 Sec
Needs a very few components
Accuracy: +-10%
Onboard 1khz wave for testing
Low power consumption
USB Interface

Step 3: Raspberry Pi Pico:

This Microcontroller has an RP2040 ARM Cotex-M0 dual-core processor and a exible clock up to 133MHz. 264KB of
SRAM, 26 GPIO pins- 3 Analog from them. 2 UART, 2-SPI, 2-I2C and 16 PWM channels. Also, have on chip clock and
temperature sensor. Supply ranges from 1.8- 5.5 volts.

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 2

Step 4: Pinout:

Step 5: Setting Up Pi-Pico:

First, download the below-given code, Then Plug your Raspberry Pico into your PC holding bootsel button to on
position. Raspberry Pi will appear as a mass storage device in the local disk manager. Copy this code in raspberry pi
storage, and it’s done.

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 3

Step 6: Code and Firmware:

Download this code from here.

Press the bootsel button on your Pico and connect it to your computer. Copy the uf2 le onto your Pico. The onboard LED
should start blinking.

Step 7: Circuit Diagram

Here, GPIO26 is channel one, and GPIO27 is channel 2. Giving a signal of 0 to +3.3 volts to any channel and GND of signal
to GND of Pi, connecting USB to the smartphone through USB completes all the connections.
For High voltages, we can add a 100k resistor to channel pins. To measure negative voltages and signals (say -3.3 to +3.3
volts), we can make a resistor divider network using a 1k resistor between 3.3v and ground that can do the job perfectly

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 4

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 5
Step 8: The Screen of Oscilloscope:

Here, a dedicated application is provided to show the waveforms and signals received from the Pico board. Named
SCOPPY, this is free to use, and through this, we can access one channel. For the second channel, we have to pay a small
amount to the creator of this App.
DOWNLOAD the Scoppy application from here.https://play.google.com/store/apps/details?id=xyz.fhdm.scoppy
It comes with an excellent interface to analyze the waveform. We can adjust the position of the wave in the X-Y direction.
Increase/ Decrease the time per division and volts per division. This application can run on an android smartphone
(Minimum requirements are Lollypop 6 or a 1.2GHz equivalent).
Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 6
Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 7
Step 9: Other Features

A sine 50Hz Demo signal with a duty cycle of 50% is provided to check the channel or do calibrations in the application.
Touchscreen also makes the moves more easier.
Also, the real-time readings of the signal are displayed in the corner, which consists of Voltage, Frequency, time and duty
cycle.
Applications also have the signal generator and logic analyzer features, which comes with the free version of the App.
The signal generator supports only sine and square waves with a frequency range of 1.25Mhz.

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 8

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 9
Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 10
Step 10: Connections With Mobile Phone:

Raspberry pi board has a micro USB port, To analyze the waveform of signal, we are using mobile phone. Connections
can be setup easily between Pico and mobile through charging jack.
Mobile charging jack also has Micro usb, so either we have to buy the supported cable or through OTG jack may do the
job. After this, make sure to select Input signal to USB.

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 11

Step 11: Oscilloscope:

Here I tried few it with few demo signals and some test signals with USB. It is cable to show waveform up to 100MHz. And
we can measure frequency and duty cycle of signal up to 250KHz.
It is useless to address higher frequency signal, but in this cost I think this is best one.
Here is the GITHUB page of maker, you may nd more details from here.https://github.com/fhdm-dev/scoppy/

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 12

Step 12: Shield for Pico Board:

Download all the les of this project from here.

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 13

Step 13: JLCPCB:

JLCPCB is the one of the most popular PCB makers. Price is just $2 for 2, 4 and 6 layer PCB. They just launched new purple
solder mask, aluminum Pcb and 3d printing service in very low cost. Pcb quality is not compromised at any cost. Check
them out right now from Here.https://jlcpcb.com/IAT
JLCPCB Is also providing new user coupons and sign-up rewards of up to $30. So, check them out from here. Register
using this link to get Free PCB assembly service coupons. Get your 2layer to 6-layer PCB’s just in $2, stencil and PCB
assembly service in just $7.

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 14

Step 14: More Projects:

1) How to make Arduino Uno clone board.

2) Breadboard constant voltage power supply module.
3) Arduino Nano clone board problems and solutions.
4) Program Arduino Using Smart Phone.
Think you enjoy my work, stay tuned. Follow us on Instagram (sagar_saini_7294) and hackaday.
Also viz. the micro usb to micro usb issue you could get female to female coupler and then use it
to join two "cheap as chips" usb phone/tablet charging leads...
https://www.ebay.co.uk/itm/302850929656
HTH
Think he made a Johnson of the app name and it's actually SCOPPY
https://github.com/fhdm-dev/scoppy\
HTH - interesting project and could be a good use for an old android phone...

Raspberry Pi Pico 200Khz Digital Oscilloscope: Page 15