Scribd
Upload
122 views2 pages

Wencon Hi Temp

Wencon Hi-Temp is a two-component epoxy coating that provides protection against wear, corrosion and chemicals at high temperatures and loads. It adheres well to metal surfaces and remains machinable after curing. Typical applications include repair of pipes, tanks and valves in marine, offshore and industrial environments operating at temperatures up to 300°C.

Uploaded by

CHI-MING WEN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
122 views2 pages

Wencon Hi Temp

Wencon Hi-Temp is a two-component epoxy coating that provides protection against wear, corrosion and chemicals at high temperatures and loads. It adheres well to metal surfaces and remains machinable after curing. Typical applications include repair of pipes, tanks and valves in marine, offshore and industrial environments operating at temperatures up to 300°C.

Uploaded by

CHI-MING WEN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Product

WENCON® Information

Wencon Hi-Temp
The high performance coating product for repair and
protection in high temperature and
aggressive environments

• High heat resistance


• Good chemical resistance No. 4 - 01.04.2013
• Excellent mechanical wear properties
• Strong adhesion to all metal surfaces
• Fully machinable

Wencon Hi-Temp is a high performance two-component,


liquid epoxy coating developed for applications in high load
areas. It provides a smooth non porous surface, which is
resistant to high temperatures, strong chemical aggression and
wear as well as bi-metallic corrosion.
Typical applications are coating of surfaces rebuild after
deterioration including repair of lining on inert gas systems,
fresh water generators, hot pipes and heating coils, protection
of tanks, pumps and valves against chemical and mechanical
aggression, corrosion and bi-metallic corrosion.
Wencon Hi-Temp has been developed for use in marine,
offshore and industry and is suitable for a wide range of
applications where high performance characteristics are
required.
Wencon Hi-Temp offers resistance to oil, water, saltwater and
wide range of acids and alkalis as well as a range of solvents.
Heat resistance ranges from 160° C (320°F) in corrosive and
heavy load environments and up to 300° C (570°F) when
applied as a filling compound.
Wencon Hi-Temp is a double coat system and is consequently
supplied in two different colours, yellow and green. The
product is liquid and is applied by brush, roller or spatula.
The Wencon products are designed to be simple to use and cost
effective. Easy mixing ratio (1:2 by volume) reduce waste to a
minimum and high specific volumes give high coverage rates.
After curing the product can be machined just like metal.

Product
IMPA no. ISSA no.
numbers:
No. 1050 Wencon Hi-Temp, yellow 0,5 kg (1,1 lb) unit 812345 75.553.12
No. 1060 Wencon Hi-Temp, green 0,5 kg (1,1 lb) unit 812346 75.553.13

WENCON ApS - Jyllandsvej 15 - DK-5400 Bogense


Phone +45 6481 1010 - [email protected] - www.wencon.com
Product
WENCON® Information

General description Coverage rate


Two component solvent free liquid epoxy Theoretical: 0,86 kg per m2 (0,17 lb/sq. ft.)
coating for protection against wear, at 600 microns.
bi-metallic corrosion and chemical aggresion Practical: 1,0 kg per m2 (0,20 lb/sq. ft.)
at high levels and temperatures.
Chemical Resistance
Surface preparation The compound is resistant to oil, water,
The surface must always be clean and saltwater and most diluted acids and alkalis
degreased as well as a range of solvents.

Applying to new steel surface:


- rounding (blunting) with radius 2mm Reduced curing time with infrared
- shot blasting to SA 2,5 This product is tested with and suitable for
- profile 75 microns infrared curing. Curing with infrared
Repairing old steel surface: radiation can reduce curing time
- rounding (blunting) with radius 2mm significantly. Result can vary, depending on
- shot blasting to SA 2,5 circumstances and equipment used.
- sweat out water and salts
- profile 75 microns Quality test
Poretest and test of layer thickness can be
Overcoating tested with normal electronic instrument
Wencon Hi-Temp is a double coat system. like high voltage and high frequency.
The overcoating time can vary from one to
three hours depending on temperature. The Shelf life
second coat must be applied while the first
At 20°C (68°F): 3 years
coat is still tacky. If full curing has occurred a
light sandblasting or grinding is necessary
prior to the second coating. Handling Precautions
Read the instructions for use and the
Material Safety Data Sheet.

Consistency : fluid
Mixing ratio vol. : 1:2
Apply with : spatula/brush
Potlife at 20°C : 20-40 min. mixed in small amounts
Curing time : 10-24 hours
Machineability : yes
Hardness shore D : 82
Tensile strength Rcrack : 13,80 N/mm2
Compressive strength Rcrack : 96 N/mm2
Compressive strength modulus of
: 4.284 N/mm2
elasticity
Adhesion steel : 22,40 N/mm2
Specific volume : 680 cm3 / kg
Temperature resistance:
Corrosion : 160°C (320°F)
Light or no load : 220°C (430°F)
For filling only : 300°C (570°F)

WENCON ApS - Jyllandsvej 15 - DK-5400 Bogense


Phone +45 6481 1010 - [email protected] - www.wencon.com

You might also like