Scribd
Upload
39 views

Instrumentation &process Control

This document discusses five common industrial processes that are monitored and controlled: temperature, pressure, flow, level, and composition. It provides details on instrumentation used to measure each process, including typical sensors and engineering units. Issues that can occur like incorrect wiring, mounting, or configuration are highlighted. The importance of validation to ensure accurate data and prevent "garbage in" is emphasized. Not all processes need complex automation, and simple systems should be kept simple.

Uploaded by

Amit Ranjan Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
39 views

Instrumentation &process Control

This document discusses five common industrial processes that are monitored and controlled: temperature, pressure, flow, level, and composition. It provides details on instrumentation used to measure each process, including typical sensors and engineering units. Issues that can occur like incorrect wiring, mounting, or configuration are highlighted. The importance of validation to ensure accurate data and prevent "garbage in" is emphasized. Not all processes need complex automation, and simple systems should be kept simple.

Uploaded by

Amit Ranjan Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 44

Instrumentation & Process

Control
Tom Koporetz
City of Kalamazoo
Five Processes to Control
T__________

P__________

F____

L_____

C___________
Five Processes to Control
Temperature

P__________

F____

L_____

C___________
Five Processes to Control
Temperature

Pressure

F____

L_____

C___________
Five Processes to Control
Temperature

Pressure

Flow

L_____

C___________
Five Processes to Control
Temperature

Pressure

Flow

Level

C___________
Five Processes to Control
Temperature

Pressure

Flow

Level

Composition
Composition (Analytical Transmitter - AT)

• pH • Phosphorus
• DO • Carbon Monoxide
• Chlorine • Carbon Dioxide
• ORP • Conductivity
• Ammonia • Oxygen
• TOC • LEL
• COD • Any other chemical or
• BOD biological process
measurements
Ron Janssen will discuss the analytical controls and
how they relate to the waste water treatment process
and some of the control schemes we use.

I will discuss general details of the remaining four


processes, Temperature, Pressure, Flow, and Level

A classic example of these processes in every day life


Fuel Engine
Level Temperature

Flow
(Speed)

Oil Pressure
A typical example of a PID control loop
that everyone can understand is cruise
control.
• Gas pedal says where it needs to be on a flat
surface.

• When you start to go up a hill the gas pedal goes


down to maintain the speed set point.

• When you start to go down hill the gas pedal backs


off to try and maintain the speed set point.
Temperature (TT)

• Sensors
• RTD (resistance thermal detector)
• Thermocouple (mVolt)

• Engineering Units
• Celsius
• Fahrenheit
Pressure (PT)

Three references for pressure


• Gauge Pressure or Atmospheric Pressure
0 psig

• Absolute Pressure or Perfect Vacuum


14.7 psia = 0 psig

• Differential Pressure (Usually “H20)


Pressure Engineering Units
• PSI or PSIG
• PSIA
• PSID
• “H2O or IWC
• mm H2O
• Feet Water Column
• “Hg (mercury)
• Kilo Pascal's (KPA)
• Meters Water Column (M)
• Many others
Flow (FT)
• Most flow (mag or turbine) transmitters measure
velocity
Inch / second

• Multiply by pipe area (inch2)


Inch / Sec * inch2 = inch3 / sec

• Convert
231 inch3 = 1 gallon
60 sec = 1 minute
Transmitters are identified by
the Process they Measure,
NOT their Principle of
Operation.
Flow (FT)
A Differential Pressure transmitter used to measure
Flow is identified as a Flow Transmitter (FT).
Level (LT)
Pressure (weight) of liquid column.

• A pressure transmitter used to measure the


process of level is identified as a Level
Transmitter (LT)
Pressure Sensing Level (LT)
Level (LT)

Ultrasonic / Radar Level Measurement

• Configurations depend on manufacturers


specifications.
Level Transmitter Configuration
Manufacturer #1 Manufacturer #2
Inputs PLC - DCS Outputs

Press (4-20) mA (4-20) mA


(0-100) AI 1 Pressure Indicator (PI) AO 1
psi

Flow (4-20) mA (4-20) mA


(0-600) AI 2 Flow Indicator (FI) AO 2
gpm

Level (4-20) mA
(4-20) mA AI 3 Level Indicator (LI) AO 3
(18-0)
IWC

Temp (4-20) mA Temperature (4-20) mA


(-50 to 100) AI 4 AO 4
deg F
Indicator (TI)

pH (4-20) mA (4-20) mA
(0-14)pH AI 5 Analytical Indicator (AI) AO 5
Standard Signals
(4-20)mA (also called 20% offset)
(0-20)mA
(1-5) Volts DC
(0-5) Volts DC
(0-10) Volts DC
(-10 to 10) Volts DC
(3-15) psi
My first lesson in my first
computer class in 1974
Garbage In
Garbage Out
You can’t make
good decisions
with bad
information!
Instrumentation Misconceptions

They are not like a


toaster.

You can’t just pull


them out of the box,
plug them in and
they’ll work.
Instrumentation Reality
• Smart Pressure Transmitter – 50 parameters to utilize
• Smart Flow Transmitters – 75 parameters to utilize
• Frequency Drive – 300 parameters to utilize
• Ultrasonic Level Transmitter – 100 parameters to utilize

• You can get the configuration 98% right and it


will function 100% wrong.
Problems That Have Been Identified
Transmitter Mounting

Water condenses in air


flow measurements
building condensate in
sample lines.
Problems That Have Been Corrected
Transmitter Mounting

Air rises to the


highest point
causing errors in
liquid sample
lines
Problems That Have Been
Corrected
• Transmitters wired incorrectly
• pH and Temperature signal wires swapped
Inputs PLC - DCS Outputs

Press (4-20) mA (4-20) mA


(0-100) AI 1 Pressure Indicator (PI) AO 1
psi

Flow (4-20) mA (4-20) mA


(0-600) AI 2 Flow Indicator (FI) AO 2
gpm

Level (4-20) mA
(4-20) mA AI 3 Level Indicator (LI) AO 3
(18-0)
IWC

Temp Temperature (4-20) mA


(-50 to 100) AI 4 AO 4
deg F
Indicator (TI)

pH (4-20) mA
(0-14)pH AI 5 Analytical Indicator (AI) AO 5
Problems That Have Been Corrected
• Misconfiguration of frequency drives.
• Too long to discuss

• Bad mapping of data to and from SCADA, PLC,


or DCS
• A Flow Transmitter wired to first PLC, mapped on to second
PLC then mapped to DCS. 600 gpm simulation indicated as
540 gpm. 10% error since initial installation.

• Three freq drives and set points mapped wrong.


• 50% signal divided by 10 and ran at 5%
Problems That Have Been Corrected
• Square root extraction incorrectly used for flow
measurement with DP sensing.

• Thermocouples
• Red wire is negative.
• Extension wire must be thermocouple wire. Can
NOT use regular wire.

• Fail safe strategies not considered.


• If you unplug a signal and don’t get an alarm it’s not
designed fail safe.
Problems That Have Been Corrected
• Damaged, wrong, inaccurately marked
equipment shipped from factory.
• Marked from the manufacturer as (0-100)deg C
but was actually (0-100) deg F

• PSIA transmitters purchased when they needed


PSIG.

• Flow Elements mounted horizontal at the high


point of the piping.
Incorrect instrument location.
Pressure sensing LT mounted at outlet of pump.
Commissioning or Validation
Most of the above issues would have been
avoided with proper Commissioning or
Validation.
This process confirms the accuracy of data
from instruments to the SCADA screens and
from the SCADA screens to the instruments.
Commissioning or Validation
Most of the above issues would have been
avoided with proper Commissioning or
Validation.
This process confirms the accuracy of data
from instruments to the SCADA screens and
from the SCADA screens to the instruments.

This is what confirms you don’t have


“Garbage In”
Commissioning or Validation

Once you have confirmed there


is no “Garbage In” then control
schemes (programming) can be
implemented and tested.
You Don’t Have to Automate
Everything!
You Don’t Have to Automate
Everything!
• If it’s a simple process keep it simple.
You Don’t Have to Automate
Everything!
• If it’s a simple process keep it simple.

• You don’t need cruise control for a horse!


You Don’t Have to Automate
Everything!
• If it’s a simple process keep it simple.

• You don’t need cruise control for a horse!

• You don’t use cruise control in a blizzard.


You need to keep your hands on the wheel,
feet on the pedals and drive the car.
Ron Janssen will be next discussing
some of our control strategies.

You might also like