Testing of Gas-Insulated Switchgear (GIS)

High Voltage Testing and Engineering Commission
Fachkommission für Hochspannungsfragen

Testing of gas-insulated switchgear (GIS)
Substations are important network nodes that must provide high availability. The projected
service life of gas-insulated switchgear (GIS) is 35 - 50 years, during which its insulation system
has to withstand all voltage loads without maintenance.
According to the latest fault statistics from CIGRE (International Council on Large Electric
Systems), the target set by the IEC (International Electrotechnical Commission) of less than
0.001 faults per year for a system's insulation has still not been attained. These statistics also
indicate that about 50% of dielectric faults occurring during operation were already present when
the systems were commissioned. This results in a requirement for more careful and stringent
testing in the factory and – in particular – on site.
As an independent institution, FKH has carried out state-

of-the-art GIS testing since the 1980s; it also undertakes
research and participates in publication activities and
other work related to this subject in international specialist
bodies. Thanks to its neutral stance, FKH can assess fail-
ures without conflicts of interest on the basis of transpar-
ent measurements.
GIS test setup on a 123 kV system
Reasons for performing high-voltage tests and diagnostic measurements and their benefits
Insulation diagnosis (such as a partial discharge measurement) will typically be carried out on GIS
in the following cases: :
 When a new system is commissioned (as part of the voltage testing)
 Due to extensions
 When systems are extended – after accidents
 Following activation of partial discharge monitoring systems (in-service measurements in
some cases)
 After weak points have been identified
 To determine the condition of the insulation (old systems, in-service measurements)
The usual test procedures are as follows (IEC):

 AC voltage test
 Partial discharge measurement FKH assists its customers with all aspects, includ-
 Lightning surge test ing GIS insulation tests, and offers support and
advice throughout the entire project:
 Test specifications for tenders, including
placement of UHF sensors
 Testing instructions (e.g. for the high-voltage
acceptance test)
 Performance of all insulation tests on high-
voltage switchgear
 Integral tests with connected high-voltage
cables are also possible
 Diagnosis and root cause analysis, including
in-service assessment
 Expert opinions
Test on a 123 kV GIS with oscillatory lightning surge
Measurement and testing options
 AC voltage test with series-resonant systems
 Conventional partial discharge measurements as per IEC
 UHF partial discharge measurement, including the sensitivity verification as per
CIGRE. The most sensitive of all UHF partial discharge measurement methods is used:
narrow-band measurement with visual selection of the measurement frequency,
together with a 50 dB pre-amplifier directly on the UHF PD sensor. In particular, this
method allows detection of critical faults with a very low partial discharge amplitude
(e.g. particles on insulation material) that could lead to a breakdown during operation in
case of transient stress (e.g. lightning)
 Lightning surge tests (with oscillatory surges where appropriate)
 Localisation of test breakdowns with a breakdown localisation system
 Localisation and identification of partial discharge findings by:
• Rough localisation via partial discharge frequency spectra and GIS sectioning
• Signal arrival-time-based PD location with state-of-the-art oscilloscopes
• Acoustic partial discharge measurement using ultrasonic sensors
• Video endoscopy with remote-controlled swivelling cameras inserted in the GIS
• Microscopy and characterisation of particles/findings
 Assessment of findings
Fault types
Types of insulation fault on a GIS
The application of test methods is merely one aspect of testing. When diagnosing dielectric faults
(especially during a partial discharge measurement), the test engineer's experience plays a
critical part in ensuring an efficient and effective test procedure. Expert assessment of partial
discharge occurrences, elimination of the partial discharge source and consideration of the need
for further investigations may all be decisive factors in preventing future GIS failures.
Multi-channel UHF partial discharge analyser Voltage test with UHF partial discharge measurement
on a 123 kV GIS S
High-voltage test and partial discharge
measurement on a medium-voltage GIS
On-site testing of a 380 kV GIS; voltage

generated via a resonant circuit
Partial discharge measurement on a 220 kV GIS
HIGH VOLTAGE TESTING AND ENGINEERING COMMISSION
FKH Head Office FKH Insulating Oil Laboratory FKH Experimental Station
Hagenholzstrasse 81 4658 Däniken 4658 Däniken
8050 Zurich
Phone: +41 44 253 62 62 Phone: +41 62 288 77 99 Phone: +41 62 288 77 95

Fax: +41 44 253 62 60 Fax: +41 62 288 77 90 Fax: +41 62 288 77 94
www.fkh.ch / [email protected] @ FKH-2019-01

Testing of Gas-Insulated Switchgear (GIS)

Uploaded by

Copyright:

Available Formats

Testing of Gas-Insulated Switchgear (GIS)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Testing of Gas-Insulated Switchgear (GIS)

Uploaded by

Copyright:

Available Formats

High Voltage Testing and Engineering Commission

Fachkommission für Hochspannungsfragen

As an independent institution, FKH has carried out state-

GIS test setup on a 123 kV system

The usual test procedures are as follows (IEC):

Types of insulation fault on a GIS

On-site testing of a 380 kV GIS; voltage

Partial discharge measurement on a 220 kV GIS

HIGH VOLTAGE TESTING AND ENGINEERING COMMISSION

Phone: +41 44 253 62 62 Phone: +41 62 288 77 99 Phone: +41 62 288 77 95

www.fkh.ch / [email protected] @ FKH-2019-01

You might also like