Volvo-Penta Tamd61a-Tamd72wja Workshopmanual Sec Wat

www.maskinisten.
net
www.classicmachinery.net
Workshop Manual D
Engine 2(0)
TAMD61A, TAMD62A, TAMD63L-A, TAMD63P-A

TAMD71A, TAMD71B, TAMD72A, TAMD72P-A,
TAMD72WJ-A
www.maskinisten.net
www.maskinisten.net
Group 21 Engine body
Marine engines
TAMD61A • TAMD62A • TAMD63L-A • TAMD63P-A
TAMD71A • TAMD71B • TAMD72A • TAMD72P-A
TAMD72WJ-A
Contents
General instructions ............................................ 2 Piston removal, gudgeon pin boss
Special tools ........................................................ 9 replacement ........................................................ 54
Piston, assembly ................................................ 55
Other special equipment ..................................... 12 Piston ring inspection and fit ............................... 56
Design and function Piston ring assembly .......................................... 56
Engine, generally ................................................. 13 Cylinder liner, inspection and measurement ........ 57
Design differences, engine versions ................... 14 Cylinder liner, disassembly ................................. 57
Identification signs .............................................. 15 Cylinder liner, honing ........................................... 58
Location of type approval plates ......................... 15 Cylinder liner position, renovation ........................ 59
Component description ....................................... 24 Cylinder liner, assembly ...................................... 60
Repair instructions Piston assembly ................................................. 61
General ............................................................... 30 Timing gears, disassembly ................................. 62
Engine jig attachment ......................................... 31 Timing gears, assembly ...................................... 65
Condition test, engine ......................................... 32 Sealant application, timing gear lid ...................... 66
Compression test ................................................ 32 Seal ring, polygon hub, replacement ................... 66
Cylinder head, renovation ................................... 32 Polygon hub, assembly ....................................... 67
Cylinder head, removal ....................................... 32 Camshaft, wear check ........................................ 67
Cylinder head, stripping/assembly ....................... 34 Camshaft, disassembly ...................................... 68
Cylinder head, leakage test ................................. 35 Inspection of valve lifters and camshaft .............. 69
Cylinder head, inspection .................................... 37 Camshaft, measurement ..................................... 70
Valve guides, inspection ..................................... 38 Camshaft bearing, replacement ........................... 70
Valve guides, replacement .................................. 38 Camshaft, assembly ........................................... 71
Cylinder head, planing ......................................... 39 Crankcase, disassembly ..................................... 71
Cylinder head, milling the seal groove ................. 39 Inspection, crankshaft and bearings .................... 72
Valve seat, replacement ..................................... 42 Crankshaft, renovation ........................................ 74
Valve seat, grinding ............................................ 43 Cylinder block, inspection ................................... 75
Valves, grinding .................................................. 44 Cylinder block, planing ........................................ 75
Rocker mechanism, renovation ........................... 44 Crankshaft, assembly ......................................... 76
Checking the valve springs ................................. 46 Big end bearings, replacement ............................ 77
Cylinder head, assembly ..................................... 46 Main bearings, replacement ................................ 78
Copper injector sleeve, replacement ................... 48 Flywheel, replacement ........................................ 80
Cleaning seat for copper sleeve .......................... 49 Gear ring, replacement ........................................ 81
Copper sleeve, assembly .................................... 50 Flywheel, indication ............................................. 82
Valves, adjustment ............................................. 52 Flywheel housing, indication ............................... 82
Cylinder block, renovation .................................. 53 Crankshaft seal, rear, replacement ...................... 83
Piston and con rod, removal ............................... 53 Flange seal, flywheel housing,
Piston and con rod, inspection ............................ 54 replacement ........................................................ 83
www.maskinisten.net
Safety information
personal injury. Avoid burns. Take precautions

Introduction to avoid hot surfaces (exhausts, turbochargers,
This Workshop Manual contains technical data, des- charge air pipes and starter elements etc.) and
criptions and repair instructions for Volvo Penta pro- liquids in supply lines and hoses when the engi-
ducts or product versions contained in the contents ne is running or has been turned off immediately
list. Ensure that the correct workshop literature is be- prior to starting work on it. Reinstall all protecti-
ing used. ve parts removed during service operations be-
fore starting the engine.
Read the safety information and the Workshop Ma-
nual “General Information” and “Repair Instruc-
tions” carefully before starting work. Check that the warning or information decals on
the product are always clearly visible. Replace
decals that have been damaged or painted over.
Engine with turbocharger: Never start the engine

without installing the air cleaner (ACL). The rota-
ting compressor in the turbocharger can cause
serious personal injury. Foreign objects entering
the intake ducts can also cause mechanical da-
mage.
Important Never use start spray or similar to start the engi-

ne. The starter element may cause an explosion
In this book and on the engine you will find the follo- in the inlet manifold. Danger of personal injury.
wing special warning symbols.
WARNING! If these instructions are not followed Avoid opening the filler cap for engine coolant
there is a danger of personal injury, extensive system (freshwater cooled engines) when the
damage to the product or serious mechanical engine is still hot. Steam or hot coolant can
malfunction. spray out. Open the coolant filler cap carefully
and slowly to release pressure before removing
IMPORTANT! Used to draw your attention to so- the cap completely. Take great care if a cock,
mething that can cause damage, product mal- plug or engine coolant line must be removed
function or damage to property. from a hot engine. It is difficult to anticipate in
which direction steam or hot coolant can spray
out.
NOTE! Used to draw your attention to important infor-
mation that will facilitate work or operations.
Hot oil can cause burns. Avoid skin contact with
Below is a summary of the risks and safety precau- hot oil. Ensure that the lubrication system is not
tions you should always observe or carry out when under pressure before commencing work on it.
operating or servicing the engine. Never start or operate the engine with the oil fil-
ler cap removed, otherwise oil could be ejected.
Immobilize the engine by turning off the power Stop the engine and close the sea cock before
supply to the engine at the main switch (-swit- carrying out operations on the engine cooling
ches) and lock it (them) in the OFF position be- system.
fore starting work. Set up a warning notice at the
engine control point or helm. Start the engine only in a well-ventilated area. If
operating the engine in an enclosed space, en-
Generally, all servicing should be carried out sure that exhaust gases and crankcase ventila-
with the engine switched off. Some work (carry- tion emissions are extracted from the working
ing out certain adjustments for example) requi- area.
res the engine to be running. Approaching a
running engine is dangerous. Loose clothing or Always use protective goggles where there is a
long hair can fasten in rotating parts and cause danger of pieces of metal, sparks from grinding,
serious personal injury. acid or other chemicals being thrown into your
If working in proximity to a running engine, care- eyes. Your eyes are very sensitive, injury can
less movements or a dropped tool can result in lead to loss of sight!
2
www.maskinisten.net
Safety information
Avoid skin contact with oil. Long-term or repea- Never expose the batteries to a naked flame or
ted contact with oil can remove the natural oils electric sparks . Never smoke in proximity to
from your skin. The result can be irritation, dry the batteries. The batteries give off hydrogen
skin, eczema and other skin problems. Used oil gas during charging which when mixed with air
is more dangerous to health than new oil. Use can form an explosive gas - oxyhydrogen. This
protective gloves and avoid oil soaked clothes gas is easily ignited and highly volatile. Incor-
and rags. Wash regularly, especially before me- rect connection of the battery can cause a spark
als. Use the correct barrier cream to prevent dry which is sufficient to cause an explosion with re-
skin and to make cleaning your skin easier. sulting damage.
Do not disturb battery connections when starting

the engine (spark risk) and do not lean over bat-
Most chemicals used in products (engine and teries.
transmission oils, glycol, petrol and diesel oil)
and workshop chemicals (solvents and paints)
are hazardous to health Read the instructions on Never mix up the positive and negative battery
the product packaging carefully! Always follow terminals when installing. Incorrect installation
safety instructions (using breathing apparatus, can result in serious damage to electrical equip-
protective goggles and gloves for example). En- ment. Refer to wiring diagrams.
sure that other personnel are not unwittingly ex-
posed to hazardous substances (by breathing
them in for example). Ensure that ventilation is Always use protective goggles when charging
good. Handle used and excess chemicals ac- and handling batteries. The battery electrolyte
cording to instructions. contains extremely corrosive sulfuric acid. If
this comes into contact with the skin, wash im-
mediately with soap and plenty of water. If bat-
tery acid comes into contact with the eyes, im-
mediately flush with copious amounts of water
Be extremely careful when tracing leaks in the and obtain medical assistance.
fuel system and testing fuel injection nozzles.
Use protective goggles! The jet ejected from a
fuel injection nozzle is under very high pressure, Turn off the engine and turn off power at main
it can penetrate body tissue and cause serious switch(es) before carrying out work on the elec-
injury There is a danger of blood poisoning. trical system.
Clutch adjustments must be carried out with the

engine turned off.
All fuels and many chemicals are inflammable.
Ensure that a naked flame or sparks cannot ig-
nite fuel or chemicals. Combined with air in cer- Use the lifting eyes mounted on the engine/re-
tain ratios, petrol, some solvents and hydrogen verse gear when lifting the drive unit.
from batteries are easily inflammable and explo- Always check that lifting equipment is in good
sive. Smoking is prohibited! Ensure that ventila- condition and has sufficient load capacity to lift
tion is good and that the necessary safety pre- the engine (engine weight including reverse gear
cautions have been taken before carrying out and any extra equipment installed).
welding or grinding work. Always have a fire ext-
inguisher to hand in the workplace. To ensure safe handling and to avoid damaging
engine components on top of the engine, use a
lifting beam to raise the engine. All chains and
cables should run parallel to each other and as
perpendicular as possible in relation to the top of
Store oil and fuel-soaked rags and fuel and oil the engine.
filters safely. In certain conditions oil-soaked If extra equipment is installed on the engine
rags can spontaneously ignite. Used fuel and oil altering its center of gravity, a special lifting de-
filters are environmentally dangerous waste and vice is required to achieve the correct balance
must be deposited at an approved site for de- for safe handling.
struction together with used lubricating oil, con-
taminated fuel, paint remnants, solvent, degrea- Never carry out work on an engine suspended
sing agents and waste from washing parts. on a hoist.
3
www.maskinisten.net
Safety information
Never remove heavy components alone, even Always use fuels recommended by Volvo Pen-
where secure lifting equipment such as secured ta. Refer to the Instruction Book. The use of lo-
blocks are being used. Even where lifting equip- wer quality fuels can damage the engine. On a
ment is being used it is best to carry out the diesel engine poor quality fuel can cause the
work with two people; one to operate the lifting control rod to seize and the engine to overrev
equipment and the other to ensure that compo- with the resulting risk of damage to the engine
nents are not trapped and damaged when being and personal injury. Poor fuel quality can also
lifted. lead to higher maintenance costs.
When working on-board ensure that there is suf-
ficient space to remove components without WARNING! The engine has pretensioned delive-
danger of injury or damage. ry lines. These pipes must under no circumstan-
ces be bent. Damaged pipes should be repla-
ced.
Components in the electrical system, ignition
system (gasoline engines) and fuel system on Observe the following rules when cleaning with
Volvo Penta products are designed and cons- high-pressure water jets: Never direct the water
tructed to minimize the risk of fire and explosi- jet at seals, rubber hoses or electrical compo-
on. The engine must not be run in areas where nents. Never use a high pressure jet when
there are explosive materials. washing the engine.
4
www.maskinisten.net
General information
About the service manual Certified engines

This workshop manual contains technical data, de- On engines which are certified in accordance with na-
scriptions and repair instructions for the standard tional and regional regulations (e.g. Bodensee), the
versions of engine units TAMD61A, TAMD62A, manufacturer guarantees that the requirements are
TAMD63L-A, TAMD63P-A, TAMD71A, TAMD71B, met by both new engines and engines in service. The
TAMD72A, TAMD72P-A, TAMD72WJ-A. product must be equivalent to the sample which was
approved during certification. In order for Volvo Penta,
The workshop manual can show the tasks carried out
as a manufacturer, to guarantee that engines in ser-
on any of the engines noted above. This means that
vice meet the stated environmental requirements, the
the illustrations and photographs may not coincide in
following requirements for service and spare parts
some cases with other engines. The repair methods
must be met:
are essentially similar, however. If this is not the
case, it will be noted. Important differences are noted l The service intervals and service tasks recom-
separately. Engine designations and engine serial mended by Volvo Penta must be observed.
numbers are noted on the type approval sign (please
l Only Volvo Penta original parts, intended for the
refer to page 15). In all correspondence about an en-
certified version of the engine, may be used.
gine, the engine designation and serial number must
always be given. l Service work related to the ignition system, igni-
The workshop manual has primarily been prepared for tion settings and fuel injection system (petrol
Volvo Penta’s service workshops and their qualified (gasoline)) must always be carried out by an au-
personnel. It is therefore assumed that people who thorised Volvo Penta workshop.
make use of the book have basic knowledge of ma- l The engine must not be changed or modified in
rine propulsion systems and can carry out tasks of a any way, with the exception of the accessories
mechanical/electrical nature which are associated with and service kits developed by Volvo Penta for the
the trade. engine.
Volvo Penta continually improves its products, which l Installation changes on exhaust pipes and air in-
means that we reserve the right to make changes. All let pipes for the engine bay (ventilation ducts)
information contained in this manual is based on prod- must not be done without consultation, since this
uct data which were available at the time the manual can affect exhaust emissions.
was sent to press. Any major changes made to the l No seals may be changed by unauthorised per-
product or service methods after this time are notified sonnel.
in the form of service bulletins.
IMPORTANT! When spare parts are required,
use Volvo Penta original spares.
The use of non-original spare parts means
Spare parts that Volvo Penta is no longer responsible for
ensuring that the engine corresponds with
Spare parts for electrical systems and fuel systems
the certified sample.
are subject to various national safety requirements,
e.g. US Coast Guard Safety Regulations. Volvo No compensation in respect of Volvo Penta
Penta spare parts meet these requirements. No com- guarantees will be given for any kind of damage
pensation in respect of Volvo Penta guarantees will be or injury caused by the use of non-original Volvo
given for any kind of damage or injury caused by the Penta spare parts on the product in question.
use of non-original Volvo Penta spare parts on the
product in question.
5
www.maskinisten.net
Repair instructions
The work methods described in the Workshop Manual
are applicable for a workshop environment. The
Our joint responsibility
engine is therefore removed from the boat and Each engine consists of a large number of interactive
mounted in an engine block. Renovation work which systems and components. The deviation of a
does not require removal of the engine is conducted in component from the technical specification can
situ with the same work methods, unless otherwise dramatically increase the environmental impact from
stated. an otherwise first-rate engine. It is therefore of
The warning symbols used in the Workshop Manual extreme importance to maintain the given wear
(see Information on Safety for implication) tolerances, that systems capable of adjustment
receive the correct setting, and that Volvo Penta
WARNING! Genuine Parts are used for the engine. The time
intervals in the engine’s maintenance schedule must
IMPORTANT! be followed.
Certain systems, e.g. components in the fuel system,
NOTE! may require special competence and special test
These are in no way comprehensive, since we equipment. Certain components are sealed at the
obviously cannot foresee everything, in that service factory for environmental reasons. Work on sealed
work is conducted under the most various conditions. components must not be conducted unless authoris-
We can therefore only point out the risks which we ation for such work is held.
consider can arise as a result of incorrect handling Remember that most chemical products, incorrectly
during work in a well-equipped workshop with work used, are hazardous to the environment. Volvo Penta
methods and tools which are proven by us. recommends the use of biologically decomposing
In the Workshop Manual all the work procedures for degreasing agents for all cleaning of engine
which there are special Volvo Penta tools are components, unless otherwise stated in the Workshop
conducted with these. The special tools are specially Manual. When working on board a boat pay special
produced to facilitate the most safe and rational work attention to make sure that oils and washing residue
method possible. It is therefore the responsibility of are handled correctly for destruction, and do not
persons using other tools or another work method than unintentionally end up in the nature, e.g. in the bilge-
that which we recommend to ensure that no risk of water.
personal injury, material damage or malfunction can
occur.
In some cases there may be special safety Tightening torques
instructions and user instructions for the tools and
Tightening torque for vital unions, which should be
chemicals named in the Workshop Manual. These
tightened with dynamometric wrenches, is listed in
instructions shall always be followed and there are no
“Specifications: Tightening torque” and indicated in the
special instructions for this in the Workshop Manual.
manual’s work descriptions. All torque indications are
By means of taking certain elementary procedures applicable for cleaned threads, screw heads and
and using a modicum of common sense, most risk mating surfaces. The torque indications refer to lightly
factors can be prevented. A clean workplace and a oiled or dry threads. If lubricants, locking liquids or
clean engine eliminate many risks both of personal sealants are required for the screw union, the type is
injury and malfunction. indicated in the work description and in “Tightening
Especially during work on the fuel system, lubrication torques”. General tightening torque as per the table
system, induction system, turbo, bearing unions and below is applicable for unions where special torque
sealing unions, it is of the greatest importance that indications are not given. The torque indication is a
dirt or foreign particles do not get in, since this can standard value and the union does not require
result in malfunctioning or shorten the repair service- tightening with a dynamometric wrench.
life.
Size Tightening torques
Nm lbf.ft
M5 ................................................. 6 4.4
M6 ................................................. 10 7.4
M8 ................................................. 25 18.4
M10 ............................................... 50 36.9
M12 ............................................... 80 59.0
M14 ............................................... 140 103.3
6
www.maskinisten.net
Safety information
In order to conduct satisfactory service work it is

Angular tightening torque therefore important that the correct type of sealant
For angular tightening torque the screw union is and locking liquids are used for the unions where such
tightened with a given torque, thereafter further are required.
tightening with a predetermined angle. Example: at In the Workshop Manual we have indicated in
90° angular tightening the union is tightened and an respective chapters the agents which are used in our
additional engine production.
1/4 turn is made in a work procedure after the given
During service work the same agent, or agent with
tightening torque has been reached.
similar properties but of other manufacture, shall be
used.
When using sealants and locking liquids it is important
Lock nuts that the surfaces are free from oil, grease, paint and
anti-rust agent, and that they are dry.
Dismantled lock nuts shall not be reused but replaced
with new items, since the locking properties diminish Always follow the instructions of the manufacturer
or are lost with repeated use. For lock nuts with concerning application temperature, hardening time
plastic inserts, e.g. Nylock®, the tightening torque and other instructions for the product.
given in the table shall be reduced if the Nylock® nut Two different basic types of agents are used on the
has the same nut height as a standard full-metal engine, and these are characterised by:
hexagonal nut. The tightening torque is reduced by
RTV-agent (Room temperature vulcanising). Most
25% for screw size 8 mm or larger. For Nylock® nuts
often used with gaskets, e.g. sealing of gasket joints
with higher nut heights, where the full-metal thread is
or applied on gaskets. RTV-agent is fully visible when
equally high as a standard hexagonal nut, the
the part has been dismantled: old RTV-agent must be
tightening torque as per the table are applicable.
removed before the union is sealed again.
The following RTV-agents are named in the Workshop
Manual: Loctite® 574, Volvo Penta 840879-1,
Strength classes Permatex®. No. 3, Volvo Penta 1161099-5,
Permatex® No. 77. Old sealant is removed in each
Screws and nuts are divided into different strength case with denatured spirit.
classes; affiliation is indicated by the marking on the
screw head. A higher number on the marking Anaerobic agents. These agents harden on the
represents a stronger material, e.g. a screw marked absence of air. The agent is used when two solid
10-9 has a higher strength than a screw marked 8-8. It parts, e.g. cast components, are fitted together
is therefore important when dismantling screw unions without gasket. A common application is also to
that the screws are refitted in their original places. For secure and seal plugs, threads on pin bolts, taps, oil
replacement of screws see the Parts Catalogue to pressure relays, etc. Hardened anaerobic agents are
ensure that the correct version is obtained. transparent and therefore they are coloured to make
them visible. Hardened anaerobic agents are very
resistant to solvents and old agent cannot be
removed. Careful degreasing is conducted prior to
Sealants refitting, and new sealant is applied.
A number of different sealants and locking liquids are The following anaerobic agents are named in the
used on the engine. The properties of the mediums Workshop Manual: Loctite® 572 (white), Loctite® 241
differ, and they are intended for different union (blue).
strengths, temperature ranges, resistance to oils and
other chemicals, and for the different materials and NOTE! Loctite® is a registered trade-mark for Loctite Corporation,
column sizes in the engine. Permatex® is a registered trade-mark for Permatex Corporation.
7
www.maskinisten.net
Safety information
l Always use gloves made of chloroprene rubber

Safety rules for fluorocarbon (gloves for handling chemicals) and protective
rubber goggles.
l Handle the removed seal in the same way as cor-
Fluorocarbon rubber is a common material in seal
rosive acid. All residue, including ash, can be
rings for shafts, and in O-rings, for example.
highly corrosive. Never use compressed air to
When fluorocarbon rubber is subjected to high temper- blow anything clean.
atures (above 300°C), hydrofluoric acid can be
l Put the remains in a plastic box which is sealed
formed, which is highly corrosive. Skin contact can
and provided with a warning label. Wash the
give severe chemical burns. Splashes in your eyes
gloves under running water before removing them.
can give severe chemical burns. If you breathe in the
fumes, your lungs can be permanently damaged. The following seals are probably made from fluorocar-
bon rubber:
Seal rings for the crankshaft, camshaft, intermediate
WARNING! Be very careful when working on en- shafts.
gines which have been exposed to high
O-rings irrespective of where they are installed. O-
temperatures, e.g. overheating during a seizure
rings for cylinder liner sealing are almost always made
or fire. Seals must never be cut with an oxy-
from fluorocarbon rubber.
acetylene torch, or be burned up afterwards in
an uncontrolled manner. Note that seals which have not been subjected to
high temperature can be handled normally.
8
www.maskinisten.net
Special tools
In all cases where it is practical, tools have had their part number punched on, but not the last figure. The last fig-
ure (after the dash) is a check sum figure.
884948 884949 9812546 9991084 9991459 9991801 9991867 9992000 9992071 9992178 9992479 9992497
9992655 9992658 9992661 9992669 9992677 9992679 9996087 9996169 9996394 9996395
884948-1 Tool for installing crankshaft gear 9992497-9 Drift for removal/installing con rod bush,
884949-9 Installation tool for polygon hub 7(x) series.
9812546-1 Plug brush for cleaning the seat and 9992655-2 Extractor for polygon hub on crankshaft
base of the injector nozzle sleeve 9992658-6 Extractor for crankshaft gear
9991084-5 Drift for removing valve guides, 7(x) 9992661-0 Drift for removing valve guides, 7(x)
series. series.
9991459-6 Drift for removing valve guides, 6(x) 9992669-3 Drift for removal/installing con rod bush,
series. 6(x) series.
9991801-3 Standard shaft, 18x200 mm 9992677-6 Drift for removal/installing rocker bush,
9991867-4 Drift for removing and installing rocker 7(x) series.
arm bushes, 6(x) series. 9992679-2 Extractor for timing gear wheels
9992000-1 Standard shaft, 25x200 mm 9996087-4 Extractor plate for lining extractor, 6(x)
9992071-2 Drift for removal/installing gudgeon pins. series.
Also used to remove the coolant pump 9996169-0 Mandrel for valve guide installation, 6(x)
9992178-5 Extractor plate for lining extractor, 7(x) series.
series. 9996394-4 Support leg (2 no.) for 9996645
9992479-7 Holder for dial gauge, for checking lining 9996395-1 Counterhold (2 no.) for 9996645
height above block plane
9
www.maskinisten.net
Special tools
9996421 9996433 9996437 9996643
9996400 9996402 9996419 9996420
9996650 9996651 9996657 9996662 9996645
9996841 9996842 9996847
9996400-9 Impact hammer. Used with 9996419 or 9996651-7 End cutter for cleaning the bed for the
9996657. copper cylinder (stage 2)
9996402-5 Mandrel for installing copper sleeves 9996657-4 Extractor for copper cylinder
9996419-9 Extractor for the steel ring above the 9996662-4 Pressure test equipment
copper sleeve 9996772-1 Tool for checking camshaft wear. Used
9996420-7 Mandrel for installing copper sleeves and with 9989876
steel rings, 7(x) series. 9996841-4 Cutting tool for opening up sealant
9996421-5 Mandrel for installing copper sleeves and grooves in cylinder head, 6(x) series*
steel rings, 6(x) series. 9996842-2 Cutting tool for opening up sealant
9996433-0 Adapter (lid). Used with 6662 grooves in cylinder head, 7(x) series*
9996437-1 Tool for installing the rear crankcase seal 9996847-1 Press tool (2 required). Used for measur-
9996643-4 Injector extractor ing lining collar height above block plane
* 9999745 Repair kit containing a cutter for cutting tools
9996645-9 Cylinder liner extractor. Used with 9996841 and 9996847.
9996394 and 9992178 or 9996087
9996650-9 End cutter for cleaning the bed for the
copper cylinder (stage 1)
10
www.maskinisten.net
Special tools
9998114
9996852 9996855 9996861 9996867 9998009 9998070 9998079 9998115
9999508
9996878 9999553
9996852-1 Connection washer for pressure testing 9998070-8 Tool for installing the copper sleeve and
the cylinder block steel ring, 6(x) series. Used together with
9996855-4 Mandrel for installing the front crankshaft 9996406 and 9996421
seal 9998079-9 Tool for lifting camshaft in and out
9996861-2 Tool for installing the copper sleeve and 9998114-4 Seal plate (2 required) for pressure test-
steel ring, 7(x) series. Used together with ing the cylinder block, 6(x) series
9996402 and 9996420 9998115-1 Seal plate (2 required) for pressure test-
9996867-9 Underlay for extracting the copper sleeve ing the cylinder block, 7(x) series
and steel ring. Used together with 9999508-6 Cutter for renovating liner seat, 7(x)
9996419 and 9996657 series1)
9996878-6 Jig for cylinder block 9999553-2 As above, but for 6(x) series2)
9998009-6 Adapter for measuring compression pres-
sure 1)
9999518 Cutter for cutting tool 9999508
2)
9999554 Cutter for cutting tool 9999553
11
www.maskinisten.net
Other special equipment
885126 9988539 9989876 9999696
Other special equipment

885126-3 Piston ring compressor
9988539-4 Compression gauge
9989876-9 Dial gauge 0–20 mm
9999696-9 Magnetic stand
12
www.maskinisten.net
Design and function
Engine, general
The engines are straight 6-cylinder, 4-stroke diesel en- Since the induction air is cooled, the combustion and
gines with overhead valves. They have direct fuel in- exhaust temperatures are kept at a suitable level, de-
jection and turbocharging. spite the higher power output.
The engines have wet, replaceable cylinder liners and Intercooling also gives lower exhaust emissions,
two separate cylinder blocks, each of which contains since combustion becomes more complete thanks to
three cylinders. The cylinder blocks are mutually inter- the greater oxygen content of the induction air.
changeable.
The turbine housing of the turbocharger is fresh
Engine lubrication is by means of a pressure lubrica- water cooled, the rest of the turbocharger is cooled by
tion system containing an efficient oil pump which the engine oil.
pumps out oil to two galleries in the cylinder block.
TAMD63-P and TAMD72 have turbochargers with
Oil is pumped out via the lubrication filter to the lubri- wastegates for greater low speed power. All engines
cation points in the engine and via a piston cooling apart from TAMD63-P and TAMD72P-A, WJ-A have
valve to the oil cooler and pistons. an electric starting heater to facilitate starting and re-
The piston cooling valve opens when the oil pressure duce exhaust smoke during starting in cold weather.
has reached a certain level, and oil is squirted into a In order to further reduce exhaust emissions, the
duct underneath the piston crown. The jet of oil is then TAMD61, TAMD62 and TAMD71 engines have a by-
led via a cooling loop in the upper part of the piston. pass valve for induction air. At low loading, the pas-
In the oil cooler, the heat is transferred from the oil to sage through the aftercooler is shut off and the air
the cooling system of the engine. which has been heated by the turbocompressor is led
directly (through the starting heater) into the induction
The oil is cleaned by means of a full flow oil filter. manifold.
The cooling system is divided up into a fresh water On the TAMD63 and TAMD72, which have higher
system and a sea water system. compression ratios, other combustion chambers and
The fresh water system is thermostatically controlled modified injection systems, this equipment is not
and cools the cylinder block and cylinder head. needed
The sea water cools the fresh water via a heat ex- The TAMD72P-A(EDC) is equipped with EDC (Elec-
changer. tronic Diesel Control), a system which electronically
Some engines can be equipped with a 1-circuit or controls the regulator in the engine’s injection pump.
2-circuit hull cooling system as follows: This system offers a reduction in exhaust emissions.
TAMD63 1-circuit system In the EDC system, the centrifugal regulator in the in-
TAMD71 1-circuit or 2-circuit system jection pump is replaced by an electromagnetic actua-
TAMD72 2-circuit system tor.
The engine version with hull cooling does not have a The actuator in the regulator is operated by a control
heat exchanger. unit which obtains information from a number of sen-
The turbo compressor supplies fresh air under pres- sors located on the engine and controls. The control
sure to the engine, which gives a large surplus of air. unit then calculates the amount of fuel to be injected
This allows the amount of fuel injected to be infor every loading case, on the basis of this informa-
creased, and this gives increased engine power. tion.
The engines are provided with sea water cooled after- Note. On the TAMD72P-A, the EDC system controls
coolers, which lowers the temperature of the induction the starting sequence so as to reduce the exhaust
air after turbocharging. This reduces the volume of the emissions to an even lower level. In order to increase
air and more air (oxygen) can be supplied to the en- the combustion temperature before starting, the
gine. The additional air allows a further increase in the start motor cranks the engine 4 turns before fuel is in-
amount of fuel injected, which increases engine pow- jected.
er.
13
www.maskinisten.net
Design and function
Design differences, engine l New sea water pump

l Stop function with solenoid valve
versions l New electrical system with sealed connectors
This workshop manual applies to all engines of the and cables run in flexible hoses. Junction boxes,
6(x) series; TAMD61A, TAMD62A, TAMD63L-A monitors and sensors have rubber mountings (vi-
and TAMD63P-A, and from the 7(x) series; bration reducing)
TAMD71A, TAMD71B, TAMD72A, TAMD72P-A l New alternator (engines with 24V electrical sys-
and TAMD72WJ-A. tems)
The most important differences are:
TAMD63P-A – TAMD63L-A
TAMD61A – TAMD62A TAMD63L-A has:
TAMD62A has: l Lower power rating
l Higher power l Injection pump with changed settings
l Pistons with modified profiles l New injector with changed opening pressure and
l Injection pump with changed settings other hole design
l Different oil change intervals l Turbocharger with wastegate valve
l New external design
TAMD71A – TAMD71B
TAMD71B has:
TAMD62A – TAMD63P-A
l Higher power
TAMD63P-A has:
l New cylinder liners, pistons and piston rings. The
l Completely new marinisation, installation volume
upper piston ring is of the “Keystone” type.
reduced by about 30%
l Injection pump with changed settings
l Higher power
l Injectors with higher opening pressure
l Low rotation cylinder head with new valve seats
for both inlet and exhaust valves. l New stop solenoid
l Increased valve clearance (inlet and exhaust)
TAMD71B – TAMD72A
l Pistons with modified combustion chambers
TAMD72A has:
l New piston rings
l Higher power
l Higher compression
l Modified cylinder heads with new valve seats
l Injection pump with RQV regulator and changed
(inlet and exhaust valves).
settings
l Changed valve clearance (inlet and exhaust)
l Reinforced pump coupling
l New upper piston rings (higher) of the “Key-
l 5-hole injector nozzles with higher opening pres-
stone” type.
sure
l New pistons with higher compression ratio and
l Reinforced (preloaded) supply pipes
suited to the new piston rings.
l Turbine optimised for high torque, integrated
l Larger oil cooler
wastegate
l Different oil change intervals
l Washable air filter
l New injection pump with higher injection pressure
l Lubrication system with “by-pass” oil filter
and changed settings.
l New oil filter bracket with horizontally located oil
l Reinforced pump coupling
filter
l New centrifugal regulator
l Larger oil cooler (same as on TAMD72)
l New injectors with changed injection pressure
l New galvanized sheet metal sump (rubber insulat-
ed from cylinder block for lower engine noise) l Reinforced supply pipes
l New heat exchanger with integrated expansion l New turbocharger with separate wastegate
tank l Electric starting heater and by-pass valve are
l New aftercooler. Modified water flow, incoming extra equipment (not normally needed because of
water passes aftercooler before heat exchanger the higher compression)
l New belt driven coolant pump l New external styling
14
www.maskinisten.net
Design and function
TAMD72A – TAMD72WJ-A l Electronic box (EDC) added, located beside the

TAMD72WJ-A is a TAMD72A which has been modi- rear fuel filter
fied for use with a water jet unit. TAMD72WJ-A has: l Stop solenoid deleted (the engine is stopped by
l New injection pump with changed settings. the EDC system)
l Different turbo without wastegate l New turbocharger with integrated wastegate valve
l Oil pipes to suit the new turbo l New rubber mounted junction box located by ex-
haust pipe
l New induction manifold
l Sensor and monitor for engine oil pressure sep-
l Higher power arately installed and rubber mounted
l Reinforced insulation on engine cables (convolut-
TAMD72A – TAMD72P-A(EDC) ed PA66 plastic hose) with moisture-proof con-
nectors
l New injection pump with electronic regulator. The
regulator contains an actuator which acts on the l New alternator with zener diodes, 24V/60A or
injector pump control rod and thus affects 12V/60A.
the injected fuel quantity (power output)
Location of type approval

plates
1. Engine designation
2. Engine serial number
3. Engine product number
4. Reverse gear designation
5. Reverse gear serial number
6. Reverse gear product number
7. Engine designation and product number
8. Serial number/short block number
15
www.maskinisten.net
Design and function
Engine presentation
TAMD61A 1 2 3 4 5 6 7
14 13 12 11 10 9
1 Junction box with circuit breakers 8 Oil cooler, reverse gear

2 Coolant filler cap 9 Reverse gear, MPM IRM 220A
3 Fuel filter 10 Dipstick (alternative location)
4 Oil filler cap (also at front edge of engine) 11 Oil cooler, engine
5 Injection pump 12 Smoke limiter
6 Stop solenoid 13 Circulation pump
7 Turbocharger 14 Alternator
1 2 3 4 5 6
7
8
9
10
13 12 2 11
1 Turbocharger 8 Sea water pump
2 Air filter 9 Heat exchanger
3 Relay for electric starting heater 10 Aftercooler
4 By-pass valve (directs air flow through aftercooler) 11 Start motor
5 Expansion tank 12 Dipstick, reverse gear, MPM IRM 220A
6 Coolant filler cap 13 Oil filler cap, reverse gear
7 Lubrication oil filter
16
www.maskinisten.net
Design and function
TAMD62A
2 3 4 5 6
14 13 12 11 10 9 8
1 Air filter 8 Lubrication oil filter (alt. location at left-hand rear

2 By-pass valve (directs air flow through aftercooler) of engine as extra equipment)
3 Filter for crankcase breather 9 Flexible engine mountings (extra equipment)
4 Aftercooler 10 Sump
5 Heat exchanger 11 Dipstick
6 Expansion tank 12 Start motor
7 Sea water pump 13 Reverse gear, MPM IRM 220A-1
14 Dipstick, reverse gear
17
www.maskinisten.net
Design and function
TAMD63L-A, TAMD63P-A
1 2 3 4 5 6 7 8
14 13 12 11 10 9
1 Fuel filter, fine 9 Reverse gear, MPM IRM 220A-1
2 Smoke limiter 10 TAMD63P-A: Wastegate valve (by-pass valve)
3 Coolant filler cap 11 Dipstick, engine
4 Injection pump 12 Solenoid valve (fuel shut-off valve) for engine
5 Oil filler cap stopping
6 Junction box with circuit breakers 13 Oil cooler, engine
7 Turbocharger 14 Flexible engine mounting (extra equipment)
8 Water cooled exhaust riser (extra equipment)
1 2 3 4 5 6 7 8
14 13 12 11 10 9
1 Filter for crankcase breather 8 Alternator

2 Air filter 9 Sea water pump
3 Aftercooler 10 By-pass filter for lubrication oil
3 Relay for electric starting heater 11 Lubrication oil filter, engine
4 Oil filler cap 12 Start motor
5 Expansion tank 13 Dipstick, engine
6 Coolant filler cap 14 Dipstick, reverse gear
7 Heat exchanger
18
www.maskinisten.net
Design and function
TAMD71A
1 2 3 4 5 6 7
8
12
11 10 9
1 Junction box with circuit breakers 7 Turbocharger

2 Coolant filler cap 8 Oil cooler, reverse gear
3 Fuel filter 9 Reverse gear, TD MG507
4 Oil filler cap (also at front edge of engine) 10 Oil cooler, engine
1 2 3 4 5 6
7
8
9
11 10
14 13 2 12
1 Turbocharger 9 Heat exchanger
2 Air filter 10 Dipstick
3 Relay for electric starting heater 11 Aftercooler
4 By-pass valve (directs air flow through aftercooler) 12 Start motor
5 Expansion tank 13 Dipstick, reverse gear, TD MG507
6 Coolant filler cap 14 Oil pump
7 Lubrication oil filter
8 Sea water pump
19
www.maskinisten.net
Design and function
TAMD71B
1 2 3 4 5 6 7
14 8
13
12 11 10 9
1 Junction box with circuit breakers 8 Oil cooler, reverse gear
2 Coolant filler cap 9 Reverse gear, TD MG507A
3 Fuel filter 10 Dipstick (alternative location)
4 Oil filler cap 11 Oil cooler, engine
20
www.maskinisten.net
Design and function
TAMD72A
1 2 3 4 5 6 7 8 9
16 15 14 13 12 11 10
1 Junction box with circuit breakers 9 Water cooled exhaust riser (extra equipment)
2 Coolant filler cap 10 Reverse gear, TD MG5061SC
3 Fuel filter 11 Oil cooler, reverse gear
4 Oil filler cap 12 Dipstick (alternative location)
5 Injection pump 13 Oil cooler, engine
6 Stop solenoid 14 Smoke limiter
7 Wastegate valve (by-pass valve) 15 Circulation pump
2 3 4 5
11 10 9 8 7
1 Air filter 7 Lubrication oil filter (alt. location at left-hand rear

2 Filter for crankcase breather of engine as extra equipment)
6 Sea water pump 11 Dipstick, reverse gear, TD MG507A-1
21
www.maskinisten.net
Design and function
TAMD72WJ-A
1 2 3 4 5 6 7 8
13 12 11 10 9
1 Junction box with circuit breakers 8 Water cooled exhaust riser (extra equipment)
2 Coolant filler cap 9 Stop solenoid
3 Fuel filter, fine 10 Alt. dipstick location
4 Smoke limiter 11 Oil cooler, engine
5 Injection pump 12 Circulation pump
6 Oil filler cap 13 Alternator
7 Turbocharger
22
www.maskinisten.net
Design and function
TAMD72P-A (EDC)
1 2 3 4 5 6 7 8
15 14 13 12 11 10 9
1 Coolant filler cap 9 Reverse gear, TD MG507-1
2 Fuel filter, fine 10 Oil cooler, reverse gear
3 Control unit (EDC) 11 Wastegate valve (by-pass valve)
4 Oil filler cap 12 Alt. dipstick location
5 Injection pump 13 Oil cooler, engine
6 Junction box with circuit breakers 14 Circulation pump
8 Water cooled exhaust riser (extra equipment)
1 2 3 4 5
11 10 9 8 7 6
1 Air filter 7 Lubrication oil filter, engine (alt. location at left-

2 Filter for crankcase breather hand rear of engine as extra equipment)
6 Sea water pump 11 Dipstick, reverse gear, TD MG507-1
23
www.maskinisten.net
Design and function
Component description
Cylinder heads 1 4
The engine has two (identical) cylinder heads, each of
which covers three cylinders. The cylinder heads are
screwed to the cylinder block by 20 screws per head
(M11).
The cylinder head material is a special cast iron alloy.
The cylinder head gasket is solid sheet steel.
The cylinder head plane has lands, formed by two
concentric wide grooves, recessed in the plane of the 2
cylinder head, centred on the cylinder liner collars.
These grooves determine the size of the sealing sur-
face so that the requisite sealing pressure is obtained 3
without the tightening torque needing to be so high
that there is a risk of deformation of the liner shelf in
the cylinder block. In addition, there is a groove for
Cylinder head sealing
the “flame edge” of the cylinder liner.
1 Cylinder head 3 Cylinder liner
The fastening screws for the cylinder head are tight- 2 Cylinder block 4 Cylinder head gasket
ened by means of a combination of torque and angle
tightening.
Valve mechanism
The valves are made from chrome nickel steel, the
valve stems are chrome plated. The exhaust valves
for TAMD71/72 and the inlet valves for TAMD63 (from
Autumn 1995) have valve heads made from Nimonic
80. The exhaust valves on other engines of the 6(x)
series have Stellite coated sealing surfaces. The
valves are operated by rockers on a rocker bridge.
The engine has two rocker bridges, one for each cylin-
der head. The rockers are operated by the camshaft,
via push rods and valve lifters.
Depending on the design of the cylinder head (valve
seat location), there are two different valve heights on
the 6(x) series. The illustration and table show the dif-
ference between the location of the valves (valve
height above cylinder head plane).
The valve seats made from special steel are inter-
changeable. Valve seats with standard dimensions A B
and overdimensions are available as spare parts. The
overdimension seat has a 0.2 mm greater overall di- TAMD62 0.7–1.1 0.7–1.1
ameter and is used if the cylinder head needs the
valve seat locations to be milled out. TAMD63 0.0–0.4 0.0–0.4
Valve location
A = Inlet
B = Exhaust
24
www.maskinisten.net
Design and function
Cylinder block
The cylinder block is cast in one piece and is made of
special cast iron alloy. The tension forces in the cyl-
inder head screws, caused by combustion pressures,
are transmitted by stiffened sections in the interior
walls of the cylinder block to the main bearings.
The camshaft bearings are broached to the correct di-
mension after assembly.
Cylinder block
Cylinder liners
The cylinder liners are of the wet type and are replace-
able. They are made from centrifugal cast iron. The
cylinder liners have a so-called “Flame edge”, please
refer to pos. 4. The flame edge, which fits a groove in
the cylinder head, reduces the stress on the cylinder
head gasket.
Four rubber O-rings are used to seal the cylinder

liner. The three lower rings are located in turned
grooves in the cylinder block. These rings are made of
different materials. The lowest seal ring (violet) is
made from fluorocarbon rubber (FPM), whereas the
two upper rings in the lower liner seal are identical and
are made of ethylene-propylene rubber (EPDM).
Note. There have been two previous versions of the

seal kit. In the first version, the two lower seal rings Cylinder liner
were identical and were made of fluorocarbon rubber
1 Cylinder head 3 Cylinder liner
(black with a green or yellow spot), whereas the upper 2 Cylinder block 4 Flame edge
seal ring in the lower cylinder liner was made of ethyl-
ene-propylene rubber (EPDM), and was marked with
two white paint spots. In another design, all the lower
seal rings were identical and were made of fluorocar-
bon rubber (marked with a green or yellow spot).
WARNING! Special safety rules apply to fluoro-

carbon rubber which has been exposed to high
temperature. Please refer to page 8.
25
www.maskinisten.net
Design and function
Pistons
The pistons are made of light metal alloy. The top
compression ring, which transmits the majority of the
heat which is transferred via the pistons, is located in
a ring carrier made of high alloy special cast iron,
which is cast in to the piston. This gives the piston
ring groove long service life despite the heat loading.
The piston ring grooves for the other pistons are ma-
chined directly into the piston.
The pistons also have a circular space inside the up-
per part of the piston, through which the oil for piston
cooling passes. On the pistons for the 6(x) series,
there is an expansion area in the gudgeon pin hole
(“side relief”), which reduces the stresses on the pis-
ton during the combustion process. The same advan-
tages are achieved on the 71 and 72 engines by
means of a trapezoid con rod end.
The combustion chamber is entirely contained within
the piston crown.
Pistons and cylinder liners are only stocked as com-
plete sets for spare part purposes.
Piston design
A Combustion chamber diameter*
B Combustion chamber depth*
Piston rings C Ring carrier
6(x) series
Piston ring profiles
Each piston has two compression rings and one oil
scraper ring.
On the TAMD61, TAMD62 and TAMD63, the top com-
pression ring is of the “Keystone” type (trapezoid)
The ring has a molybdenum coating and must be in-
stalled with the TOP marking upwards.
The second compression ring (chrome plated), which
is slightly conical and has a turned internal chamfer,
must be installed with the TOP marking upwards.
The oil scraper ring (chrome plated) may be installed
either way up.
The ring has two scraper edges which are pressed
against the cylinder wall, both by the spring force of TAMD 61, TAMD62 TAMD 63
the ring itself and by an expansion spring located in-
side the scraper ring. The opening in the expansion
springs should be located diametrically opposite to the
gap in the oil rings*.
* TAMD63: The white paint spot on the spring should be visible

through the outer ring gap.
Gudgeon pin hole with “side relief”
26
www.maskinisten.net
Design and function
TAMD71
Each piston has three compression rings (early ver-
sion), or two compression rings (later version)* and
one oil scraper ring.
The upper compression ring on the early version is
chrome plated and has a turned internal chamfer, and
on the later version it is molybdenum coated and must
be fitted with the TOP marking** uppermost. The
TAMD71B has a top ring of the “Keystone” type.
TAMD 71 Early version TAMD 71 Later version
The second ring, and on the early versions, the third
ring as well, are slightly conical and have to be in-
stalled with the TOP marking** upwards. On the early
versions, the rings are coated with Ferrox. (Ferrox at-
tracts oil and thus has a lubricating effect.)
The second compression ring also has three Ferrox
filled grooves, and the third compression ring has a
turned internal chamfer.
On the later version, the second compression ring is
chromed and has an internal chamfer, the third com- TAMD 71B TAMD 72
pression ring has been abolished.
The oil scraper ring is of the same type as on the 6(x) Piston ring profiles
series.
* The pistons on the later version still have 4 piston ring

grooves, but the third groove is empty.
** TOP, TOPCX TOPCF or a machined mark (-).
TAMD72
Each piston has two compression rings and an oil
scraper ring. The upper compression ring is of the
“Keystone” type and is unique to the 72 series (differ-
ent height), and is installed with the “TOPCD” marking
upwards.
The other rings are similar to the TAMD71B.
27
www.maskinisten.net
Design and function
Timing gear
The timing gear consists of cylindrical gear wheels
with spiral cut teeth.
The injection pump and camshaft are driven from the
crankshaft gear via an idler gear. The engine oil pump
is also driven from the crankshaft gear via an idler
gear.
In addition to the camshaft, the camshaft gear also
drives the gear for the sea water pump (the sea water
pump on the TAMD63 is driven by a Poly-Vee belt).
If a servo pump is fitted (extra equipment), this is also
driven from the camshaft gear.
Three different surface treatments have been used on
the gear wheels; case hardening, hardening & temper-
ing and nitrocarburising. Please refer to the instruc-
Timing gear
tions about nitrocarburised gears on page 61 before
replacing any gear wheels. 1 Sea water pump drive
2 Camshaft gear
3 Idler
4 Injection pump drive
5 Coolant pump drive
6 Crankshaft drive
7 Idler for oil pump
8 Oil pump drive
Crankshaft
The crankshaft is supported on seven main bearings.
The thrust bearings consist of thrust washers on the
centre main bearing. The crankshaft is statically and
dynamically balanced. At the front, the crankshaft has
a so-called polygon profile, and the rear there is a
flange to which the flywheel is screwed.
The crankshaft is nitrocarburised. On condition that
the shaft does not need to be re-aligned, it can be
ground down to the 2nd underdimension before it
needs to be nitrocarburised again.
Crankshaft with con rods and pistons
Big and small end bearings

The big and small end bearings consist of indium plat-
ed, lead bronze lined steel shells. The bearings are
precision made and are entirely ready for installation.
Five under-dimensions can be obtained as spare
parts. The thrust washers for axial location of the
crankshaft are available in three overdimensions.
28
www.maskinisten.net
Design and function
Con rods
The con rods have an I section, and are drilled for
pressure lubrication of the gudgeon pins. Since the
con rods have obliquely split big ends, they can be
pulled up through the cylinder bores during engine ren-
ovation.
The gudgeon pin bushes are made of steel and have a
bronze alloy lining.
On the 71 and 72 series, the con rods have trapezoid
small ends, to give a larger effective bearing area
against the gudgeon pin.
Con rods with trapezoid small end (71 and 72 series).
Camshaft
The camshaft is drop forged and induction hardened,
the cams are profile ground. The camshaft runs in
seven bearings. End float is determined by the cam-
shaft gear wheel, the shoulder on the foremost cam-
shaft bearing journal and the thrust washer screwed to
the front surface of the cylinder block.
Flywheel
The flywheel is screwed to a flange on the rear of the
crankshaft. It is statically balanced and fully ma-
chined. The flywheel ring gear is shrunk onto the fly-
wheel.
Torsional damper
The torsional damper consists of a hermetically
sealed housing containing a steel flywheel bob of rect-
angular section. The flywheel bob (damping ring) ro-
tates on a central bushing and is surrounded on all
sides by a viscous fluid (silicone compound).
Torsional damper
1 Crankshaft 6 Housing
2 Hub 7 Lid
3 Fluid space 8 Timing gear housing
4 Bushing 9 Seal ring
5 Flywheel bob
29
www.maskinisten.net
Repair instructions
General Measures before renovation outside the

boat
Before every major service task, a condition test
should be carried out if possible, to determine the gen- 4 Lift the boat up onto land
eral condition of the engine and to find any co- 5 Turn off the battery isolator, remove the battery
operating fault causes. It is necessary to operate connections from the start motor.
the engine during a condition test, so this should be
6 Remove the connector between the engine
done before the engine or any engine components are
cables – instrument panel
removed.
7 Remove the sea water connections/hull cooler
Please refer to condition test, engine, on page 32.
connections.
8 Remove the exhaust pipe
9 Shut off the fuel cocks. Remove the fuel pipes.
10 Remove the throttle and gear shift cables
11 Undo the propeller shaft from the reverse gear.
Undo the engine pads from the bed and lift the
Measures before renovation in the boat engine out.
1 Turn off the battery isolator
2 Clean the outside of the engine
Measures after lifting out the engine
NOTE! Make sure that washing residue is taken
12 Clean the engine
care of for destruction, and is not inadvertently
dumped into the environment. WARNING! When you are clean the engine
Please refer to the warning text in item 11 as with a high pressure washer. Be very careful
well. when cleaning, to avoid water entry into the
3 Work on the cooling system: Shut off the sea engine. When the high pressure function is
cocks and drain the coolant from the sea water engaged, the water jet must never be aimed
and fresh water systems. at seals, e.g. shaft seals, joints with gas-
kets, rubber hoses or electrical components.
WARNING! Make sure that all sea cocks
are securely shut and that water can not get 13 Drain the engine oil off.
in when you disassemble any components 14 Remove the reverse gear (if necessary).
in the cooling system.
30
www.maskinisten.net
Repair instructions
Engine stand attachment

Jig no. 9996787 is used to attach the engine to the Before the engine jig can be fitted, and the engine at-
engine stand. The jig is screwed to the right-hand side tached to the engine stand, the following components
of the engine, as in the illustration below. must be removed from the engine:
NOTE! It is important that the note about the numbers
and dimensions of screws is observed, for safe at- TAMD61/62
tachment of the engine.
Heat exchanger, aftercooler, start motor, oil filter
Screws required: bracket, front engine mounting and rear hatch for
valve lifter.
6(x) series 7(x) series
3 no. M8x30 mm M8x30 mm TAMD63
2 no. M10x30 mm M10x30 mm Heat exchanger, aftercooler, start motor, oil filter
2 no. M12x40 mm bracket, front engine mounting, rear hatch for valve
lifter, air filter and expansion tank
TAMD71/72
Heat exchanger, aftercooler, start motor, oil filter
bracket, rear hatch for valve lifter and oil filter hous-
ing.
1 M8x30 mm 4 M10x30 mm [6(x) series]

2 M10x30 mm [6(x) series] 5 M12x40
3 M8x30 mm
31
www.maskinisten.net
Repair instructions
Condition test, engine Cylinder head, renovation
Compression test Cylinder head, removal

Special tool 9998009 Special tool nos. 9996643, 9996847*
A compression test is done in order to assess the TAMD61/62/63, TAMD 71/72

condition of the engine in a simple and reliable man-
ner, this indicates the sealing ability of the piston 1
rings and valves. Remove both battery cables
l Warm the engine up and stop it.
2
l Remove all the injectors and test each of the cyl-
inders in turn. Close the sea cocks and drain the water in the fresh
water and sea water systems.
WARNING! Observe the greatest possible
If the engine has a hull cooling system, close the
cleanliness, to avoid getting dirt into the fuel
valves for this system and drain the engine.
system. Plug the connections where injectors
and fuel pipes have been disconnected.
Applies to TAMD61/62, TAMD 71/72
The compression pressure should be read off att nor- 3

mal start motor speed. A deviation of 10% below the Remove the shield over the heat exchanger and after-
data given on page 6 in the “Technical data” manual cooler. Remove the filter.
can be approved.
Low compression pressure in all cylinders indicates 4
worn cylinder liners and piston rings. If you find one
Remove the pipe between the sea water pump and the
cylinder whose values lie below the others, this could
heat exchanger, and between the aftercooler and re-
be caused by either poorly sealing valves, broken cyl-
verse gear oil cooler.
inder rings or a cylinder head gasket which does not
seal properly.
5
Remove the lid on the heat exchanger (rear heat ex-
changer on the TAMD71 and TAMD72). Remove the
connecting pipe to the aftercooler (or to the front heat
exchanger on the TAMD71 and TAMD72).
Release the breather pipe (plastic) from the expansion
tank.
6
Remove the coolant pipes between the heat exchang-
er and the coolant pump, and between the heat ex-
changer and thermostat housing.
Remove the heat exchanger.
7
Remove the connection pipe between the aftercooler
and the induction manifold and between the aftercool-
er and the by-pass valve.
Remove the aftercooler.
Insert adaptor no. 9998009 into the injector hole and
attach it with the fastening brace and nut for the injec- 8
tor. Remove the connection pipe between the starting
Fit a compression gauge to the adaptor and do the heater and the induction manifold. Hang up the brack-
compression test. et with the starting element relay.
32
www.maskinisten.net
Repair instructions
9 19
Free the plastic pipe for the smoke limiter from the If the engine has a stop solenoid, remove it and hang
front edge of the induction manifold. Remove the in- it up.
duction manifold.
Applies to all engines

Applies to TAMD63 20
10 Shut off the fuel taps. Remove the fuel pipe leading to
Undo the alternator bracket and lift the generator away the fine filter, the supply pipes and the fuel leakage
with its bracket, plus the oil pressure sensor and oil pipes. Remove the fuel filters.
pressure monitor with bracket. Install protective covers.
21
11 Remove the coolant pipe between the oil cooler and
Remove the clamps for the cable harness at the the thermostat housing lid.
lower edge of the heat exchanger and the inter- Undo the flange for the coolant pipe by the front edge
cooler. of the exhaust manifold.
Undo the electrical connections to the temperature
sensor.
12
Remove the cooling water hoses to and from the heat 22
exchanger and the aftercooler. Remove the thermostat housing and the connection
pipe.
13 23
Remove the vent pipe at the front of the heat ex-
changer and the pressure hose for the smoke limiter.
14
Remove the screw behind the heat exchanger.
15
Remove the 5 remaining screws which hold the heat
exchanger and lift it away from the engine.
Remove the injectors*

16 Remove the yoke and turn the injector forwards and
backwards with a spanner (PU-15), at the same time
Remove the air filter housing, the air supply pipe and as you pull it out. If the injector has stuck, use ex-
the hose between the turbocharger and the aftercool- tractor no. 6643. This avoids the risk of pulling the
er. copper sleeve out at the same time.
17 * If you are very careful to avoid damaging the injector nozzle

Remove all screws holding the induction manifold. tips, the cylinder head can be removed with the injectors in
place.
18
Undo both the screws behind the aftercooler a few
turns and lift the aftercooler off.
33
www.maskinisten.net
Repair instructions
24
Cylinder head disassembly/
Free the exhaust pipe from the turbocharger.
Remove the coolant pipe between the turbo and the
assembly
cylinder block. Special tool: 885128
Remove the oil pipes for the turbocharger. Install pro-
tective covers.
25
Remove the turbocharger and exhaust manifold. Cov-
er the turbo inlet and outlet with clean paper or use
some other method, to prevent dirt and other
foreign matter from entering the turbocharger.
26
Remove the valve covers. Undo the rocker bearing
screws, remove the rocker mechanism and pushrods.
NOTE! Mark the push rods or put them in a stand, in

the correct order.
27
Remove the cylinder head screws and lift the cylinder
head off. Remove the cylinder head gaskets, rubber
seals and their guides from the cylinder block.
Cylinder heads in the 6(x) and 7(x) series have twin

valve springs (an inner and an outer spring).
28
Clean the cylinder head and cylinder block mating fac-
es.
29 Disassembly
Install two press tools 9996487 to retain the cylinder The cylinder head core plugs should not be removed
liners1). unless damage makes this necessary. The valves
and valve springs must be re-installed in their original
1)
locations if they are to be re-used. Use marked stands
Necessary if work is going to be done where the crankshaft is
turned with the cylinder head detached. The cylinder liners then
or small component boxes to ensure correct location.
have to be retained by 1 press tool no. 9996487 per cylinder
liner. 1
Remove the valve springs and valve by means of a
valve spring compressor. Remove oil seals, collets,
collars and valves.
The oil seals (protective ring above the collets) should
always be scrapped and replaced by new ones.
34
www.maskinisten.net
Repair instructions
2 1
Clean all components, be especially careful with the
oil and coolant galleries.
Remove any remaining soot and contamination from
the cylinder head mating surfaces. Clean the sealing
grooves with a suitable scraper (shaped to conform
with the contours of the grooves).
NOTE! Never pass a rotating steel brush or other tool

across the sealing grooves. The lands would then be
broken down and ruined.
Connect the proof testing equipment to the com-

pressed air mains and set the pressure gauge to
Assembly 100 kPa (1 kp/cm2), using the reduction valve.
3
NOTE! The reduction valve knob can be locked with a
Clean the core plugs if they have been removed.
lock ring which is moved along the spindle.
Clean the core plug seats.
Use Permatex® No. 3 or Volvo Penta 1161099-5 seal-
ant. 2
Install the plug by means of a mandrel or sleeve.
Then close the shut-off tap. During 2 minutes, the
pressure on the pressure gauge must not fall, for the
4 proof testing equipment to be regarded as being reli-
Oil the valve stems and install the valves in their able.
guides.
NOTE! Observe the markings, to ensure that the

valves go back to their original locations.
3
5
Install the valve spring(s) and valve collar, and press
the spring(s) together with the valve spring compres-
sor. Install the collets and a new valve stem seal.
Cylinder head, leakage check

Special tools: 9996662, 9996852
6(x) series 9998114 (2 no.), 7(x) series 9998115
(2 no.)
WARNING! Before using proof testing Attach air connection plate 9996852, using two M10
equipment no. 9996662, it must be checked. Al- screws and seal plates 9998114 (6x series) or
ways observe the applicable safety 9998115 (7x series), using twelve M10x120 mm
instructions. screws and nuts.
35
www.maskinisten.net
Repair instructions
4 7
Check that the knob on the reduction valve of the Screw in the reduction valve knob to give a pressure
proof testing equipment is screwed out. of 50 kPa (0.5 kp/cm2) on the pressure gauge. Main-
tain this pressure for 1 min.
5
Connect the hose from the proof testing equipment to
the air connection plate.
8
Then raise the pressure to 150 kPa (1.5 kp/cm2).
Lock the reduction valve knob with the lock ring and
shut the tap off.
Check after one or two minutes whether the pressure
6 has fallen and if any air bubbles come out of the water
bath.
If there is any air leakage from the copper sleeves for
the injectors, this should be attended to in accordance
with “Copper sleeves for injectors, replacement” and
“Cleaning seats for copper sleeves” on pages 46 to
48.
Lower the cylinder head into a bath of water at 70°C

and open the tap.
36
www.maskinisten.net
Repair instructions
Cylinder head, inspection Warpage

The warpage of the cylinder head must not exceed
0.03 mm.
The check is made with a feeler gauge and steel
ruler, whose sides has been shaved to an accuracy
corresponding to DIN 874/Normal. If the cylinder head
is found to be warped more than the permitted value,
the cylinder head must be planed or replaced.
If leakage has been found, or if the cylinder head has
blow-by lines, measurement is unnecessary, since a
cylinder head in this condition will have to be planed
or replaced anyway.
NOTE! The cylinder head on the TAMD63 must not be
planed, it should always be replaced if damaged.
Check that the seal grooves which are centrally above
the cylinder liners are undamaged.
For sealing grooves, please refer to “Cylinder head,
milling the seal grooves” on pages 39–42.
Cracks
When renovating engines with a large number of oper-
ation hours, heat cracks may be found between the
valve seats and the injector hole when the cylinder
head is inspected.
The cylinder head does not need to be replaced be-
cause of heat cracks.
The crack starts by the copper sleeve for the injector
and grows towards the valve seat location. The rea-
son for the crack can be that the attachment yoke is
too done up too tightly, i.e. the wrong torque has been
used. Cracks of this type have not been known to
cause gas or coolant leakage, since the crack has not
grown through the base of the cylinder head.
When leakage has been found, it has been found to
be caused by contamination or damage to the copper
sleeve seat.
Please refer to “Cleaning the seat for the copper
sleeve” on pages 49 and 50.
37
www.maskinisten.net
Repair instructions
Valve guides, inspection Valve guides, replacement

Special tools: 9999876 and 9999696. Special tools: 6(x) series: 9991459, 9996169,
7(x) series: 9991084, 9992661.
1
Put the cylinder head on a flat surface and put new
valves in the guides.
The valve spindles should rest on the flat surface. If 1
necessary, remove the injector fastening studs to get
good contact.
Press out the valve guides with mandrel 9991459 6(x)

series, or 9991084 7(x) series.
Place dial gauge 9989876, with magnetic stand

9999696, so that the tip of the dial gauge rests upon
the edge of the valve head. Move the valve sideways 2
in the direction of the inlet and exhaust ports.
Oil the new valve guides and press them in with man-
Read the values on the dial gauge. drel 9996169, 6(x) series, or 9992661 7(x) series. The
mandrel gives the guides the correct height (23 mm
and 22 mm respectively) above the spring plane of the
cylinder head.
Wear tolerances
Inlet valve, max. clearance ............... 0.33 mm
Exhaust valve, max. clearance ......... 0.38 mm
3
If these values are exceeded, change the valve
guides. Broach the valve guides up if necessary.
38
www.maskinisten.net
Repair instructions
Cylinder head, planing Cylinder head, milling the seal

Special tools: 9992479, 998976. groove
Special tools: 998976 and 9992479 + 9996841, 6(x)
The warpage on the cylinder head must not exceed series; 9996842, 7(x) series
0.03 mm.
If the warpage exceeds this value, or if blow-by lines
occur, the cylinder head must be planed or replaced.
Please refer to the “Technical Data” section of the
workshop manual for the minimum height of the cylin-
der head.
Surface finish after planing must not exceed 1.6 RA.
NOTE! The cylinder head on the TAMD63 must not
be planed, it should always be replaced by a new one.
After planing, new seal lands and flame edges must
be milled.
Milling tool 9996841, 9996842,

1 Nut 5 Spindle
2 Turning handle 6 Cutting head
3 Guide plate 7 Bit holder
4 Attachment screw
1
Permitted distance (A) between the cylinder head When new grooves are milled, the cylinder head must
plane and valve head: be planed so as to completely remove the old
grooves.
The height of the cylinder head, plus the distance be-
6(x) series 7(x) series.
tween the plane of the valve heads and the cylinder
Inlet valve ................. 0.7 – 1.1 mm 2.0 – 2.4 mm* head plan must not fall below the values given in the
Exhaust valve ........... 0.7 – 1.1 mm 1.0 – 1.4 mm* specifications section.
The grooving tool is centred with the flame edge
* TAMD72A: 0 ± 0.2 mm
groove bit, and not with the guide plate as on other
grooving tools.
This is the reason why the guide plate attachment
If the permitted distance (A) is not met after planing, screws have wide clearance in the valve guides.
the valve seats must be milled out.
39
www.maskinisten.net
Repair instructions
2 Setting the cutters

Set up the cutter head in a vice, with the bits facing
upwards.
The grooving tool has five bits. Three of them (Marked

A-A*-B) are intended to work the flame edge groove.
These should be adjusted to 2.8 mm +0.1, –0.2 mm.
Attach the dial gauge (998976) in holder 9992479 and
put this on the ring-shaped land on the cutting tool.
Zero the dial gauge against the land.
Slide the holder and dial gauge sideways so that the

gauge tip rests on the highest point of one of the cut-
The remaining bits (marked C-D) are intended to work
ters, and read off the dial gauge.
the sealing plane, and should be adjusted to ±0.02
mm.
Adjusting the bit

6
Sealing grooves in cylinder head.

Undo lock screw “A” with a 4 mm Allen key, and turn
adjustment screw “B” a few turns with a 5 mm Allen
key.
40
www.maskinisten.net
Repair instructions
7 12
Press down the bit holder and tighten the lock screw Install the bit holders in the cutter head, in accordance
enough to press against the holder. with the letters, and with the grooves aligned towards
the lock screws. Adjust the bit height as instructed.
8
Put the dial gauge tip on the highest point of the bit
and turn the adjustment screw upwards until the cor-
rect value of bit height is obtained.
Tighten the lock screw.
NOTE! Check that the upper edge of the bit holder is
on the same plane as the cutter head. If it is not, the Milling the grooves
dial gauge has turned one rotation too many.
13
Set the cylinder head up in a vice.
9
WARNING! Use protective jaw pads to avoid
Set all bits to the specified depth, as in items 2 and 3. damaging any sealing surfaces.
Make sure that the cylinder head plane is com-
pletely clean.
Changing the bit set * 14
10 Put the guide plate of the tool on the cylinder head,

but do not tighten the nuts for the attachment screws.
Unscrew the lock screw a few turns and turn the ad-
justment screw upwards so that the bit holder can be
removed from the cutter head.
15
11
The bit holders are marked with a letter (A, A*, B, C Carefully put the cutting head on the guide plate, us-
or D), and the corresponding letter is punched on the ing rotating movements, so that the tool is centred on
cutter head, where the bits are to be installed. the flame edge groove.
NOTE! The two socket cap screws in the bit holder NOTE! Do not tighten the nuts for the attachment
must not be touched. screws too hard, this could pull the valve guides into
* 9999745, repair kit for cutting tool 9996481 and 9996482. the cylinder head.
41
www.maskinisten.net
Repair instructions
16
Valve seat, replacement
Special tools: 9992479, 998976
Install the spring and nut. Tighten the nut loosely.
17
Turn the tool clockwise, using even movements, and The valve seat should be replaced when distance (A),
without pressing. The cutters are fed automatically. measured with a new valve, exceeds
Turn the tool until the cutter bits stop cutting.
Remove the nut and lift off the cutting head. TAMD61/62 TAMD63 TAMD71/72
Inlet .......... 1.5 mm 1.0 mm 3.0 mm
Exhaust .... 1.5 mm 1.0 mm 2.0 mm
18
Clean the cylinder head carefully. Then check the
depth of the grooves by putting the cutting head back, 2
without the spring and nut, and turn it a few times un-
der hand pressure. If the tool cuts, the grooves do not
have the correct depth.
This check must always be done since swarf can get
under the collar of the cutting head.
The burrs left by the edges of the grooves should be
left in place.
If these burrs are broken off, the edges could be dam-
aged, which would impair the sealing properties of the
grooves.
NOTE! The first time the grooving tool is used, after The old valve seat should be removed by grinding two
the bits have been adjusted, the finished groove must notches in the seat, and then splitting it with a cold
be checked with a dial gauge. chisel. As an alternative, an old valve can be tack
welded in several places, and the old seat can then be
During this check, any burrs on the edge of the
driven out.
grooves must be carefully removed, so that the dial
gauge holder seats correctly against the cylinder Grind down the head of the scrapped valve so it can
head. be pushed down below the edge of the seat.
Weld with a MIG/MAG welder, cover the area round
the weld to avoid getting weld spatter stuck anywhere.
WARNING! Be careful not to do any damage to

the cylinder head.
42
www.maskinisten.net
Repair instructions
3 Mill or grind the valve seats. A new valve seat must

Clean the valve seat location carefully, and check that be ground down so that the distance between the cyl-
there are no cracks. Measure the diameter of the inder head plane and the valve head (A), measured
valve seat location. Use the measurement to deter- with a new valve, is:
mine whether a STD or OD dimension seat should be
used. TAMD61/62 TAMD63 TAMD71/72
Do any machining on the valve seat location. Cool the *Inlet ......... 0.7–1.1 mm 0–0.4 mm 2.0–2.4 mm
new valve seat down in carbon dioxide snow to
–60 to –70°C, and possibly heat the cylinder head by Exhaust .... 0.7–1.1 mm 0–0.4 mm 1.0–1.4 mm
hosing it with hot water or other means. Press the
valve seat in with a mandrel.
A used valve seat (wear tolerance) may be ground
down so that the distance between the cylinder head
NOTE! Align the new valve seat correctly, with the plane and the valve head (A), measured with a new
valve chamfer outwards! valve, is max.:
You must do the work quickly, so as to maintain the
greatest possible temperature difference.
TAMD61/62 TAMD63 TAMD71/72
Machine the seat to the correct angle and width.
Inlet .......... 1.5 mm 1.0 mm 3.0 mm
Exhaust .... 1.5 mm 1.0 mm 2.0 mm
If the distances are greater, the seats should be re-

placed.
Check the seat angle with a plug gauge for valve
seats, once the valve seat mating surface has been
coated with a thin layer of marking dye.
* To give acceptable renovation service life and economy, the

seat should be replaced when 0.2 mm remains to the maximum
wear tolerance, once the valve seat has been ground.
Valve seat, grinding

Before grinding, the valve guides must be checked
and replaced if the wear limits have been exceeded.
When the valve seats are ground, only remove just
enough material to give the correct shape and a good
mating surface.
Valve and valve seat
43
www.maskinisten.net
Repair instructions
Valves, grinding Rocker mechanism,

(does not apply to engines with Nimonic renovation
valves)* Special tools: 6(x) series 9991876, 7(x) series
* Note. Nimonic valves must not be ground. 9992677.
Valve sealing angles:

Inlet: 29.5°
Exhaust: 44.5°
1
Check the valves before grinding them. Cracks and

damage to the valve head or bent valve stems always
mean that the valve must be replaced. Grind the seal-
ing surface as little as possible, just enough to make
it clean all the way round. If the valve head edge is Remove the circlips from the rocker shaft and remove
less than 1.2 mm wide after grinding on the 6(x) se- the rockers, bearing journals and springs.
ries, or 2.0 mm (inlet) and 1.0 mm (exhaust) on the
7(x) series, the valve must be replaced.
Always grind the mating surface in with grinding paste
(even on new valves and seats), and check mating
with indicator dye. If there is any lack of sealing, re- 2
grind the seat but not the valve. Then grind the valve Clean the components. Be especially careful with the
in with grinding paste and do a new check with indica- oil duct in the bearing journals, and the oil holes in the
tor dye. rocker shaft and rockers.
Check the distance (A) between the plane of the
cylinder head and the valve head, as in item 1 under
the method for “Valve seat, replacement” on page 42.
3
Check the wear on the rocker shaft and the sealing of
the top hat plugs in the ends of the shaft. Also check
that the spherical part of the rocker arm is not de-
formed or worn. The threads on the adjustment
screws and locknuts must be undamaged. The hexa-
gon on the locknut must also be in good condition.
The spherical bearing surface of the rocker arm, which
is in contact with the valve/valve cap must not be un-
evenly worn or pitted. If there is minor wear, this can
be evened off by a grinder. If the rocker shaft hole is
worn oval, the rocker must be replaced.
44
www.maskinisten.net
Repair instructions
4 7
Oil the rocker shaft and install all the components.

Note that the rockers on the 6(x) series are installed in
opposing pairs. On the 7(x) series, all the rockers are
identical and the location on the shaft is thus arbitrary.
Make sure that the circlips on the rocker shaft ends
Press out the rocker bushing with mandrel no. have seated securely in their grooves.
9991967 for the 6(x) series, or 9992677 for the 7(x)
series.
Turn the mandrel over and press in a new bushing.

NOTE! Make sure that the oil hole in the bushing is
centred on the oil duct in the rocker arm.
6
Machine broach the bushing to give an accurately ad-
justed running fit on the shaft.
22.020–22.041 mm for the 6(x) series, or
25.020–25.042 mm for the 7(x) series.
Remove all swarf.
45
www.maskinisten.net
Repair instructions
Checking the valve springs Cylinder head, assembly

Special tools: 9992479, 9996847
1
Clean the mating planes of the cylinder head and cyl-
inder block. Remove any rust or carbon from screw
holes and from the threads for the cylinder head fast-
ening holes. Clean the holes with a tap (M11 x 1.5).
Remove all loosened dirt with a vacuum cleaner or
compressed air.
2
Check the lining heights. Please refer to the values
noted in “Technical Data” in the workshop manual.
The difference in height between the linings under one
and the same cylinder head must not exceed 0.02
mm.
For measurement and adjustment, please refer to
“Cylinder liner position, renovation” on page 59.
3
Dip the cylinder head screws (including the screw
heads) in rust proofer, part no. 282036-3, and allow
Check the valve spring lengths, unloaded and when them to run off on a piece of netting. The screws
loaded by a spring tester. should have stopped dripping when installed (oil could
The springs must maintain the values noted in “Tech- otherwise be forced up and be regarded as leakage).
nical Data” in the workshop manual. WARNING! The screws are phosphated and
must not be cleaned with a steel brush. If the
cylinder head is painted, the contact surfaces
for the cylinder head screws must be free of
paint. The clamping force in the threaded fast-
eners could otherwise be very poor.
Install the seal rings and put the cylinder head gas-
kets in place. Put the two rear cylinder head screws in
the cylinder blocks and install the cylinder blocks.
46
www.maskinisten.net
Repair instructions
Torque the cylinder head screws in the numbered se-

quence in the tightening schedule, four times.
6
Install the push rods and rocker mechanism. Tighten-
1st tightening: 30 Nm (3 kpm)
ing torque: For the 61 series with steel bearing caps,
2nd tightening: use 65 Nm (6.5 kpm)
6(x) series: 85 Nm (8.5 kpm) Later versions of the 61 series, and all engines in the
7(x) series: 90 Nm (9 kpm) 62 and 63 series should have a torque of 50 Nm (5.0
3rd tightening: kpm).
6(x) series: 85 Nm (8.5 kpm) The 71 and 72 series engines should have 65 Nm (6.5
7(x) series: 90 Nm (9 kpm) kpm).
4th tightening:
Angle tighten the screws 60° in numbered order, as * The steel bearing cap has been replaced by an aluminium bear-
follows: ing cap as a spare part.
Mark up the screw head positions with chalk

marks on the screws and cylinder head. Do not 7
use a centre punch or scriber, since this could
Adjust the valve clearance and install the valve
cause confusion later on.
covers, as in the instructions on page 52.
Mark up a 15 mm socket, put the socket as in the
illustration above, i.e. with the sleeve marking dis-
placed one spanner flat anti-clockwise from the
chalk mark.
Then carry out the angle tightening by turning until
the sleeve marking coincides with the chalk mark
on the top of the cylinder head.
Once all screws have been tightened 60°, tighten-
ing is completed. No subsequent torquing is nec-
essary.
47
www.maskinisten.net
Repair instructions
5
Copper sleeve for injectors
Special tools, 6(x) series: 9812546, 9996400,
9996402, 9996419, 9996421, 9996643, 9996650,
9996651, 9996657, 9996867, 9998070
7(x) series: 9812546, 9996400, 9996402, 9996419,
9996420, 9996643, 9996657, 9996861, 9996867
The copper sleeve can be changed with the cylinder

head either installed or detached.
The seat for the copper sleeve must never be cleaned
up with a cutting tool, with the cylinder head still in-
stalled on the engine.
The seat may be cleaned with a nylon brush with the
cylinder head still installed on the engine. Pull out the steel ring above the copper sleeve. Use
extractor no. 9996419 together with underlay 9996867.
NOTE! To avoid damaging the extractor spindle during
extraction, the spindle must be kept stationary and
tightening must be done with the nut.
Measures to be taken with the cylinder It is the nut which must do the work.
The tool can be supplemented by impact hammer
head installed 9996400.
1
Drain the coolant (fresh water system).
6
2
Clean round the injectors. Remove the fuel leakage
pipe and fuel supply pipes. Plug the connections.
Remove the valve covers. Pull the copper sleeve out with extractor no. 9996657.
NOTE! Do not undo the individual pipes. Remove all

the pipes as a package, i.e. all the pipes which are
clamped together.
IMPORTANT! No fuel pipe must be bent or

deformed, since cracks may occur which
would lead to failure.
3
Remove the injector retaining yoke, where the copper
sleeve is to be replaced, and the dust cover over the
injector.
4
First press the extractor sleeve to the base of the
copper sleeve. Hold the extractor still and turn the
spindle anti-clockwise until the tool grasps the copper
sleeve firmly.
Turn the injector with a 15 mm open-ended spanner,

and pull it upwards at the same time. If the injector is
stuck, it must be removed with puller no. 9996643.
48
www.maskinisten.net
Repair instructions
7
Cleaning the seat for the
copper sleeve
Method 1 – with a plug brush (installed or
detached cylinder head)
Special tool 9812546
It is very important that all kinds of deposits on the

mating surface in the cylinder head, of the copper
sleeve are removed before a new copper sleeve is in-
stalled.
IMPORTANT! For TAMD63, cleaning with

When the extractor has grasped the copper sleeve a plug brush is the only permitted method.
firmly, insert underlay 9996867 and thread the extrac-
tor sleeve over the spindle.
Pull out the copper sleeve by screwing the nut down
at the same time as you hold the spindle still. The tool
can be supplemented by impact hammer 9996400 if
1
necessary.
Install plug brush 9812546 in an electric drill with ad-

Injector and copper sleeve justable speed. The maximum speed for the plug
brush is 1000 rpm. Insert the plug brush into the in-
1 O-ring 4 Steel ring
2 Copper sleeve 5 Protective ring
jector hole and clean the seat. Blow clean with com-
3 Seal ring 6 Yoke pressed air.
8
Check that the O-ring has come up with the copper
sleeve, and that the lower sealing plane is clean.
If the sealing plane is damaged or covered in carbon,
it can either be cleaned with a plug brush (nylon
brush) or with a cutter.
Please refer to methods 1 and 2 under “Cleaning the
seat for the copper sleeve” on this page and overleaf.
Remove the upper seal ring (3). Clean the upper and
lower guides in the cylinder head.
49
www.maskinisten.net
Repair instructions
Method 2 – with a cutter (detached Copper sleeve, assembly

cylinder head)
Special tools, 6(x) series: 9996402, 9996421, 9998070
Special tool: 9996650, 9996651 7(x) series: 9996402, 9996420, 9996861
Cleaning up with a cutter is done in two stages. Injector and copper sleeve
NOTE! Only use a cutter if absolutely necessary,
since the location of the injector in the cylinder head
is changed each time the seat is re-cut. The cutter
must not be used on the TAMD63, method 1 must
be used instead.
IMPORTANT! The cutter must only be used

when the cylinder head is detached, because
of the risk of getting swarf into the engine.
1 O-ring 4 Steel ring

2 Copper sleeve 5 Protection ring
3 Seal ring 6 Yoke
It is important that the steel ring and copper sleeve

are changed at the same time, to give the correct
clearance between the ring and the sleeve. The O-ring
and the upper seal ring should always be replaced by
new ones.
First clean up with cutter no. 9996651 until the cutter

1
bottoms on the top sealing plane of the seat, and
stops cutting. Coat the upper seal ring (3) with Vaseline or soapy
water and put it in the cylinder head.
The cutter cuts on the surfaces indicated by arrows,
please refer to the illustration.
2 Install a new O-ring around the lower guide for the

2
Then continue to clean up with cutter 9996650, until

the cutter bottoms against the cone and stops cutting. copper cylinder. Put a new steel ring and copper
sleeve on mandrel no. 9996421 (6x series) or 9996420
The cutter cuts on the surfaces indicated by arrows,
(7x series).
please refer to the illustration.
Guide the mandrel down into the cylinder head.
Check the seal surfaces. If necessary, repeat the

cleaning process. Also check that the upper seal seat
is clean. Blow the cylinder head clean of swarf.
50
www.maskinisten.net
Repair instructions
6x-series 6x-series
7x-series 7x-series
3
(6x series): Remove the two fastening screws for the
cylinder head (one on each side of the copper sleeve).
Screw down press tool no. 9998070.
(7x series): Screw down press tool 9996861 with the
injector attachment screws.
Clearance between the copper sleeve and steel ring.
4
Screw down the press tool screw against the mandrel,
and press the steel ring and copper sleeve down by 5
torquing to 58 Nm (5.8 kpm) with a torque wrench. Install mandrel 9996402 and then re-install the press
Remove the press tool and mandrel. tool (9998070 or 9996861). Press the copper sleeve
down by torquing the press tool to 58 Nm (5.8 kpm)
with a torque wrench.
NOTE! The steel ring and copper sleeve must be

pressed down in two operations to obtain the correct
press force on the copper sleeve, and the correct
clearance between the ring and sleeve. The clearance
should be 0.10–0.45 mm, please refer to pos (A) on
the illustration above. (6x series) and (7x series).
51
www.maskinisten.net
Repair instructions
6
Remove the press tool and mandrel.
(6x series): Install the cylinder head screws and
torque them. Please refer to “Cylinder head, installa-
tion” on pages 46 and 47.
7
Inlet ❍
Exhaust ●
Valve location and cylinder numbering
Valve clearance,
Inlet Exhaust
TAMD61, TAMD62, ............. 0.40 mm 0.55 mm
TAMD71 (0.0157”) (0.0217”)
TAMD63, TAMD72, ............. 0.50 mm 0.65 mm
TAMD73, TAMD74 (0.0197”) (0.0256”)
Install the injectors with dust covers and yokes. 1

Tightening torque is 50 Nm (5.0 kpm/37 lbf.ft). Install
the valve covers and oil leakage pipes. Remove the valve covers. When the valve clearance
is checked, the engine must only be cranked in its
normal direction of rotation. Cranking is done by turn-
ing the polygon hub on the crankshaft nose with a 21
mm ratchet spanner.
8
Install the delivery pipes. Check that they have not
been skewed and tighten the nuts. Firing sequence 1 5 3 6 2 4
Tightening torque is 15–25 Nm (1.5 –2.5 kpm/11–18 Cylinder whose
lbf.ft). rockers “tip” 6 2 4 1 5 3
2
9
Crank the engine in its normal direction of rotation un-
Fill up with coolant. Do a leakage check.
til the No. 1 piston is at TDC after the compression
stroke. This will cause the valves for cylinder No. 6 to
“tip”.
3
Crank the engine a third of a stroke in the correct di-
rection of rotation, and check the valve clearance for
piston No. 5. At the same time, the valves for cylinder
No. 2 will “tip”. Check the valve clearance for the
other cylinders in the firing sequence.
4
Valves, adjustment Clean the valve covers, replace damaged gaskets.
NOTE! The clearance must never be checked when Tightening torque for nuts for the valve cover is
the engine is running, it must be done with the engine 24 Nm (2.4 kpm/18 lbf.ft).
stationary, cold or at operating temperature. Test the engine and check that no oil leakage occurs.
52
www.maskinisten.net
Repair instructions
3
Cylinder block, renovation
Turn the engine round until the relevant piston is at
BDC. Remove the big end bearing cap with the lower
bearing shell.
Piston and connecting rod,
removal
4
(Cylinder head and sump removed)
Special tool: 9996847.
Please refer to “Cylinder head, removal” on pages 32

and 33 for the method of removing the cylinder head.
Carefully tap the con rod and piston up until the piston
rings come free of the cylinder liner.
Lift off the piston together with the con rod.
5
Install retainers 9996847 for the cylinder liners, before
removing the pistons. Remove the piston rings with piston ring pliers.
If a cylinder liner should slide up during piston re- Please refer to page 54 for inspection of the piston
moval, the cylinder liner must also be removed since rings.
there is a major risk that contamination will fall down
between the lining and the block, and cause leakage.
Remove the piston cooling nozzle.
IMPORTANT! The piston cooling nozzle must

always be removed even if the work could “theo-
retically” be done with the nozzle in place. There
is a considerable risk that you could knock and
bend the nozzle, which would cause an engine
failure. The lock nuts must not be re-used.
53
www.maskinisten.net
Repair instructions
Piston and con. rod, inspection Removal of piston, small end

bush replacement
Special tools: 9991801, 9992071, 9992479 (7x series),
9992669 (6x series)
Before the small end bush is replaced, the con rod

must be checked for cracking, straightness and twist.
A cracked, bent or twisted con rod must be scrapped.
Checking piston wear
Check the pistons for cracks, damaged piston ring

dowels and worn piston ring grooves. If the piston has
deep grooves on the skirt surface, the piston
(liner kit) must be scrapped. Likewise, if the piston
has one or several cracks in the gudgeon pin hole or
in the base of the combustion chamber. Cracks on the
edge of the piston crown around the combustion
chamber are generally of no consequence. Carry out a Remove the gudgeon pin retaining circlips and press
crack test by means of the chalk dust test. If any kind the gudgeon pin out with mandrel 9992071.
of damage has occurred, the injection equipment must
be checked as well.
Check the wear on the gudgeon pin. There must not
be any noticeable slack.
The gudgeon should have a light interference fit in the
piston when cold, max. 0.004 mm. 2
NOTE! The cylinder liner wear must be checked be-
fore piston rings, small end bushings etc. are re-
placed.
Please refer to “Cylinder liner, inspection and mea-
surement” on page 57.
Use a new gudgeon pin and measure the con rod in a

jig.
The gudgeon pin may have the following tolerances:
A. Straightness: Max. 0.05 mm per 100 mm length.
B. Twist: Max. 0.1 mm per 100 mm length.
54
www.maskinisten.net
Repair instructions
3
Piston assembly
Special tool: 9992071
Press the old bush out, using mandrel no. 9992669

(6x series) or 9992479 (7x series). and shaft no.
9991801.
4 Install one circlip on the piston. Heat the piston up to

Heat the con rod up to about 100°C. about 100°C.
5
2
Press in the new bush, using the same tool as was

used for extracting the old one. Make sure that the oil
hole in the new bush coincides with the oil duct in the
con rod. Draw a guide line on the bushing hole and the
con rod with a felt tip pen. Check after pressing the
new bush in, that the oil duct is open. Oil the piston, gudgeon pin and small end bush with
engine oil.
6
After pressing, the bush for the
3
6(x) series should be broached
7(x) series should be bored
When the correct fit is achieved, an oiled gudgeon pin
should slowly slide down through the bush under its
own weight (at room temperature).
Finish off by checking the con rod in the jig again, to
ensure that the oil hole is correctly aligned.
Place the piston and con rod so that both the front
marks are aligned in the same direction.
55
www.maskinisten.net
Repair instructions
4 During measurement, the ring should be pressed down

below the Bottom Turning point using a piston.
Replace the piston rings if the gap is 1.5 mm or great-
er.
In general, piston rings should be replaced if there is
any noticeable wear (within the wear tolerances) in the
cylinders, since the piston rings do not normally end
up in the same positions as they had before removal.
Check the piston ring gap on new piston rings as well.

Please refer to “Technical Data” in the Workshop Man-
ual for measurements for each engine variant.
Note. New cylinder liners are supplied complete with
pistons and piston rings.
Press the gudgeon pin in carefully with mandrel no.

992071 and install the second circlip.
NOTE! It should be possible to press the gudgeon pin
in easily, it must not be driven in with a hammer.
Inspection and fit of piston Piston rings, assembly

rings Install the piston rings on the piston by means of pis-
ton ring pliers.
The oil scraper ring must be installed first, and can be
installed either way up. The expansion spring gap
should be located on the opposite side to the oil
scraper ring gap.*
The compression rings are marked; (the TOP, TOPCD
TOPCX or machined mark) should be at the top.
For a further description of the various versions and
installation locations, please refer to the “Piston ring”
heading on pages 26 and 27.
* White paint marks on the spring should be visible through the
ring gap.
Checking the piston ring gap
Check the wear surfaces and sides. Black spots on

the surface indicate poor contact, and mean that the
piston ring must be replaced.
Oil consumption also has a considerable bearing on
when piston rings should be replaced.
Check the piston ring gap (please refer to the illustra-
tion above).
56
www.maskinisten.net
Repair instructions
3
Cylinder liner, inspection and
If the wear is greater than 0.35–0.40 mm, the cylinder
measurement liner with pistons and piston rings should be replaced.
NOTE! The piston and cylinder liner are only supplied
as a complete set as spare parts. The pistons and
Inspection cylinder liners are classified and marked with a letter,
C, D or E. This means that a piston marked E must
The cylinder liner should be carefully cleaned before
only be installed with a liner marked E.
inspection and measurement. The cylinder liner must
be removed from the cylinder block to permit accurate
crack checking.
IMPORTANT! The position and number of the

cylinder liner must be marked with a felt tip pen
before the liner is removed.
NOTE! Routine removal of the cylinder liner should

not be done unless measurement or other checks indi-
cate that replacement, honing or careful crack check-
ing is necessary.
The Magnaflux method can be used for crack check-
ing.
Measurement
1
Measure the wear on the cylinder liner with a cylinder
indicator. To get the most accurate wear measure-
ment possible, the cylinder indicator should first be
Cylinder liner, removal
1
set with a gauge ring or micrometer. Special tools, 6(x) series: 9996087, 9996394 (2 no.),
Use the original diameter of the cylinder liner as the 9996395 (2 no.), 9996645
starting value. 7(x) series: 9992178, 9996394 (2 no.), 9996395
(2 no.), 9996645
Measure the upper and lower turning points in the cyl- Mark up the cylinder liner (cylinder and installation lo-
inder liner, and at several points along the height of cation) if it is to be re-used.
the liner. At each measurement point, the measure- Assemble the extractor with extractor plate 9996087
ment must be done in the transverse and lengthwise (6x series) or 9992178 (7x series). Pull out the cylin-
directions of the engine. der liner. Remove the seal rings.
57
www.maskinisten.net
Repair instructions
Clean the removed cylinder liner from sooty edges.

Cylinder liner, honing
Set the liner up in a vice.

Use a heavy electric drill which can be operated at low
speed, 200–400 rpm.
Use a Flex-Hone® tool with no. 80 grit.
Honing pattern on cylinder liner bore
It is important that the cylinder liner should retain its NOTE! Do not use a honing tool with grinding stones,
original honing pattern, for good lubrication and seal- since these machine the entire surface of the bore.
ing. The liner should therefore be honed if it has sur- Lubricate the bore with thin engine oil before and dur-
face scratches because of a ring seizure or dirt, or ing honing.
has bright spots (polishing).
After honing, it is very important that the cylinder
Honing with the cylinder liner in place is not recom- liner is carefully cleaned. Use hot water, a brush
mended, because of the risk of getting contamination and detergent (never paraffin or diesel oil).
into the oil ducts and the difficulty of doing the mea-
surements correctly. Dry the liner with paper or a lint-free cloth. Oil the cyl-
inder liner with thin engine oil after drying.
The cylinder liners have a honing pattern (see illustra-
tion), whose angles are carefully calculated to give the
optimum service life. When the bores are honed in Flex-Hone® is a registered trade mark of the Brush Research
Manufacturing Co. Inc.
conjunction with piston ring replacement, the original
pattern should be followed to safeguard lubrication.
The honing scratches must be applied regularly and
cut evenly in both directions and over the entire cylin-
der.
NOTE! You must maintain the correct speed on the
honing tool to get the correct pattern.
1
58
www.maskinisten.net
Repair instructions
Calculate the thickness of spacers needed, on the ba-

Cylinder liner seat, renovation sis of the measurements you have made. Try to use
Special tools: 9989876, 9992479, 9996847 (2 No.), the thinnest possible spacer, preferably only one
9999508 (7x series), 9999514 (7x series), 9999538 should be used. The correct height above the block
(6x series), 9999553 (6x series) plane should be 0.38–0.43 mm.
A damaged cylinder liner seat is repaired by milling

the lining shelf. Check the mating face of the upper
2
lining seat with marking dye if there is any doubt
about the extent of the damage. The material which is Remove the liner and roughen up the surface of the
removed during milling should be compensated lining seat with an emery cloth.
by spacers which are available in thicknesses of
1.12 mm (only 7x series), 0.20 mm, 0.30 mm and
0.50 mm.
NOTE! If spacers are to be used, the lining seats will 3
have to be machined slightly, even if the seats are un-
damaged, this is because the fillet radius has to be re-
moved to allow the spacers to seat correctly.
Clean the upper and lower lining seats and estimate
the extent of the damage. The upper seat must be ab-
solutely clean from carbon deposits. Clean
the mating surfaces with a brush and cleaning fluid.
Scraping tools must not be used in any circum-
stances. Blow dry with compressed air.
Screw milling tool no. 9999553 (6x series) or 9999508

(7x series) to the cylinder block.
1 Make sure that the feed sleeve does not press on the
cutter.
4
Screw down the feed sleeve so that it presses the
cutter lightly. Use a T handle (not a ratchet handle) to
turn the cutter.
The cutter should be turned with an even movement,
at the same time as the feed sleeve is turned. When
the correct height has been reached, stop feeding and
turn the cutter a few turns.
Remove the milling tool and clean the liner seat care-
fully.
Check the mating surface of the lining seat very care-
fully, and the height of the step edge at regular inter-
vals.
NOTE! Mark the position of the liner against the cylin-
der block with a felt tip marker pen, so that it comes
back to the same position again.
Install the cylinder liner without sealing rings, and
press it down with holder 9996847 (2 No.).
Measure the height of the liner above the plane of the
block at four different locations, using a dial gauge
and measurement jig 9992479.
59
www.maskinisten.net
Repair instructions
5
Cylinder liner, installation
Put any spacers required on the cylinder liner seat.
Special tools: 9989876, 9992000, 9992479, 9996847 Lubricate the new seal ring and install it beneath the
(2 No.), 9996854 liner collar.
1
Remove the old seal rings from the cylinder block and
make sure that the sealing surfaces are carefully
6
cleaned.
Use cleaning fluid and a brass brush.
NOTE! Scraping tools must not be used.
2
If the cylinder liner has not been renovated, install the
cylinder liner without sealing rings and screw it down
with two press tools no. 9996847.
Press the cylinder liner down carefully. Use mandrel

no. 9996845 together with handle 9992000.
7
Use press tool no. 9996847, 2 No. to keep the cylin-
der liner in place.
Measure the height of the liner and estimate the thick-

ness of spacers required as in item 1 of the method
described in “Cylinder liner seat, renovation” on page
59.
4
Lubricate the seal rings to be installed in the cylinder
block with the lubricant provided in the seal ring pack-
age.
Install the rings in the grooves in accordance with the
installation instruction provided on the package.
60
www.maskinisten.net
Repair instructions
NOTE! The cylinder liner press tool must be removed

Piston assembly temporarily when tool no. 885126 is used. When the
Special tool: 885126 piston is in place, the press tool must be put back
again.
1
Oil the piston with engine oil. 5
Check that the bearing shells are correctly aligned in
the con rod. Install the cap in accordance with the
marking, and install the screws.
2
6
Make sure that the press tool is in place, and turn the
crankshaft until the piston comes to its lowest posi-
⇒
tion.
Torque the screws to 190 ± 10 Nm (19 ± 1.0 kpm).
7
Install the piston cooling nozzle.
Make sure that the piston ring openings point in differ-
ent directions on the piston.
Oil the big end bearing shells and the gudgeon pin
with engine oil.
Install the bearing shells and check that they are cor-
rectly aligned in relation to the con rod and cap.
4
Install the piston and con rod in each cylinder, with
the arrow and “Front” marking pointing forwards.
Use tool no. 885126 to guide the piston rings down
into the cylinder liner.
61
www.maskinisten.net
Repair instructions
l Remove the shield plates above the heat ex-

Timing gear, disassembly changer and remove the aftercooler. Remove the
Special tools: 9992655, 9992658, 9992697 two plastic pipes from the expansion tank.
l Remove the lid at the front of the thermostat

housing and the connection pipe to the coolant
pump.
l Remove the coolant pump.
l Turn the engine round in its normal direction of ro-

tation until the no. 1 piston is at TDC after the
compression stroke (0° on the flywheel).
TAMD63
l Remove the belt tensioner, free the alternator and
hang it up.
l Remove the alternator bracket.
l Remove the circulation pump drive gear (4

Timing gear screws).
1 Crankshaft gear 5 Injection pump drive gear
2 Idler gear 6 Coolant pump drive gear* NOTE. The work noted under preparatory work does
3 Oil pump drive gear 7 Timing gear not need to be done if a complete renovation is going
4 Idler gear 8 Sea water pump drive gear
to be done (removal of all shafts and gears), it only
* Not installed on TAMD63. needs to be done if work is only going to be done on
part of the timing gear.
IMPORTANT! Never turn the crankshaft or cam-

shaft when the timing gears have been removed
and the cylinder head is still in place. The pis-
Preparatory work tons and valves can come into contact with
TAMD61, TAMD62, TAMD71, TAMD72 each other and be damaged.
l Free the oil filter and bracket, and hang it up.

Alternatively, the pipes between the engine and
oil filter can be removed. Remove the filter and
1
bracket. Avoid spilling oil.
Remove the crankcase pulley, if one is fitted, plus the
torsional damper, which is screwed to the polygon
l Remove the oil filling pipe at the front of the en- hub.
gine. Remove the connection pipe to the coolant
pump. IMPORTANT! The torsional damper must not be
Remove the sea water pump and connection subjected to impacts. The damper characteris-
pipes. tics can be completely changed if the shape of
the fluid chamber is changed by dents.
l Remove the alternator and drive belts. Remove

the alternator brackets, the expansion tank and
the connection pipe to the thermostat housing.
l Remove the electrical junction box from the ex-

pansion tank and hang it up.
62
www.maskinisten.net
Repair instructions
2 5
Remove the idler gear (pos 4)* together with the bear-
ing pin and thrust washer.
Remove the polygon hub centre screw, remove the

washer and pull the hub off with tool no. 9992655.
Remove the camshaft gear (pos 7)* with extractor no.

999279. Use the same procedure as for the injector
3 pump drive wheel (pos 5)*.
Remove the timing gear cover.
4 8
Remove the crankshaft gear (pos 1)* with extractor

no. 9992658.
Check that all the markings (centre punch dots) on the * Please refer to the overview of the timing gears on page 62.
gears coincide. Adjust if necessary by turning the
crankshaft round.
63
www.maskinisten.net
Repair instructions
Inspecting the timing gears

Clean the gear wheels and other components in the
timing gear, and inspect them carefully. Replace any
gear wheels which are heavily worn or damaged.
During assembly, all clearances must be checked.
Max. permitted gear flank clearance is 0.17 mm.
Check the radial clearance and end float of the idler
wheel.
End float .................................... 0.05–0.15 mm
Radial clearance ........................ 0.025–0.082 mm
Clean the timing gear cover and the mating surface of

the cover on the engine (timing cover)
Nitrocarburised timing gear wheels

Since some of the timing gear wheels are more heavi-
ly loaded in some engine versions than in other ver-
sions, the timing gear wheels on these engines are
made to withstand heavier loading, by nitrocarburising
them.
WARNING! Nitrocarburised gears must not

be installed in contact with quenched and
tempered gears.
Always observe the spare part catalogue when replac-

ing gears. If you are not sure about the grade of a
gear, nitrocarburised gears can be recognised by the
following signs:
l Nitrocarburised gears have a matte grey to yel-

low/grey colour.
l The gears are marked with white oil-resistant
paint or have an “N” or NITRO punched on them.
64
www.maskinisten.net
Repair instructions
2
Timing gear, assembly
Check that the camshaft drive gear dowel is installed.
Special tools: 884948, 884949 Install the camshaft drive gear.
Tightening torque is 70 Nm (7 kpm)
IMPORTANT! All gear wheels in the timing gear Tightening torque for timing gears.
which are important for timing are marked with a
centre punch mark on the relevant gear tooth or
tooth gap. Also, please note the instructions for
installing nitrocarburised gears on page 64.
3
Tightening torque for timing gear.
90 ±9 Nm
(9 ±0.9
Nm) 70 ± 7 Nm
(7 ± 0.7 Nm)
33 ±4 Nm
(3.3 ±0.4 Nm)
70 ±7 Nm 33 ±4 Nm
(7 ±0.7 Nm) (3.3 ±0.4 Nm)
Set the crankshaft up with the no. 1 piston at TDC

(crankshaft key straight up).
Install the idler gear in accordance with the markings.
1 The thrust washer is positioned as in illustration (A).
4
Check that the dowel is installed in the injector pump
shaft (not TAMD63, TAMD72) and install the pump
gear. Check that the markings on the gears coincide.
Note. The injection pump drive gear on the TAMD63
and TAMD72 does not have markings against the idler
gear.
5
Check that there are no marks of seizure on the cam-
shaft nose and the polygon hub. Polish off any marks
Check that the crankshaft key is installed and is cor- with emery cloth.
rectly seated in the groove. Remove the old seal ring for the polygon hub.
Install the crankshaft gear with tool no. 884948. Clean the seal ring mating surface.
NOTE! Make sure that the teeth are correctly engaged Please refer to item 2 of “Seal ring, polygon hub” on
in the oil pump drive gear. page 66 for instructions about installing the seal ring.
65
www.maskinisten.net
Repair instructions
Application of sealant, timing Seal ring, polygon hub,

gear cover replacement
(With polygon hub removed)
1
Remove the old seal ring by means of a screwdriver.
Clean the seal ring mating surface in the lid.
Note. On early model engines, the seal consists of an
inner rubber ring and an outer felt ring. These have
been replaced as spare parts by a rubber seal which
is used on late model engines, i.e. 1 rubber seal is in-
stalled.
Apply an even, 2 mm wide string of sealant on the

timing gear cover.
Use sealant no. 1161231-4.
NOTE! The timing gear cover must then be installed
and screwed down within 20 minutes.
Install a new seal ring on mandrel 999 6855.

Oil in the seal ring and tap it in until the mandrel
bottoms.
66
www.maskinisten.net
Repair instructions
Polygon hub, installation Camshaft, wear check

Special tool: 884949 Special tools: 998976, 9996772
Preparatory work
1
l Remove the valve covers. Remove the screws
holding the rocker shaft bearing caps and remove
the rocker mechanism. Lift the push rods out.
Mark the push rods so that they end up in the
same place during re-assembly.
Valve location and cylinder numbering
Lubricate the crankshaft nose with molybdenum disul-

phide compound. Install the centring section of man-
drel no. 884949 (A) on the crankshaft nose.
Heat up the polygon hub to about 100°C. Drive the
hub quickly onto the crankshaft nose (B) until it is
about 5 mm from the plane of the gear wheel.
Remove the tool. Install the washer and centre screw. Inlet valve m
Torque the screw to 200 Nm (20 kpm). Exhaust valve l
Leave the hub to cool and torque the screw to
260 Nm (26 kpm). Front of engine
2
Install the torsional damper and crankshaft pulley.
1
Torque the screws to 90 Nm (9 kpm).
Install tool no. 9996772 with two M10x20 screws be-

side the front valve lifter (cylinder 1 exhaust valve).
Install the dial gauge on the tool.
67
www.maskinisten.net
Repair instructions
2 4
Install the push rods in the correct order, install the
rocker support bridges and torque the screws.
Tightening torque: for the 61 series with steel bearing
caps*, torque to 65 Nm (6.5 kpm).
Later models of the 61 series and all engines in the 62
and 63 series have aluminium bearing caps. Tighten-
ing torque is 50 Nm (5.0 kpm).
On the 71 and 72 series, the torque used is 65 Nm
(6.5 kpm).
Valve adjustment, please refer to page 52.
* The steel bearing cap has been replaced by an aluminium bear-
ing cap as a spare part.
A B Camshaft, removal
Adjust the length of the push rod in the tool, so as to
give a pre-load on the exhaust valve lifter.
Crank the engine until the push rod of the tool is at its Preparatory work
lowest position (A).
• Remove the components which cover the valve
Check that the push rod has pre-load and zero the dial
lifter access hatch, as in items 1–19 in the
gauge.
“Cylinder head, removal” method on pages 32
Turn the flywheel round until the push rod of the tool is
and 33.
at its highest position (B).
Remove the timing gear as in items 6 in the “Tim-
Read off the value on the dial gauge.
ing gear, removal” method on page 62.
Note the value.
1
3
Remove the valve covers.
Move the measurement tool push rod over to the inlet
valve lifter and do the same measurement.
Move the tool and measure the lift height of each cyl- 2
inder in turn. None of the values may be less than the
minimum lift height values given in the table below. 2
1
Camshaft lift Min lift height

in mm in mm
m inlet l exhaust m inlet l exhaust Remove the rocker support bridges (1) and con rods
(2).
6(x) series ...... 8.000 8.000 7.8 7.8
7(x) series ...... 8.006 8.268 7.8 7.8 NOTE! Mark the con rods or put them in a stand so
that they go back in the same places on re-assembly.
Lift heights, camshaft
68
www.maskinisten.net
Repair instructions
3
Inspection of valve lifters and
camshaft
Remove the valve lifter access hatches (3).

NOTE! The centre hatch does not need to be re-
moved.
Inspection of valve lifters
4 Use a steel rule to check that the surface of the valve

lifter in contact with the camshaft is spherical (con-
vex). It may even be flat, but it must absolutely not be
concave. If there is visible light showing through the
lifting surface between the ruler and the valve lifter,
the lifter must be replaced.
NOTE! If the valve lifter is worn right across the valve
lifter, the lifter must be scrapped. The “ditch” shows
that the valve lifter has not rotated. On the other hand,
a dark line at the outside of the valve lifter shows that
the surface has not been worn down.
Investigate the reason why the valve lifter has not ro-
Remove the valve lifters (4) and mark them so that tated before installing a new valve lifter.
they go back in the same places when put back.
5
B
A
Minor pitting damage on valve lifter (A), camshaft (B).

Remove the camshaft flange (5).
Check the valve lifters for pitting damage. Pitting
damage can occur for various reasons. The damage
6 is caused by small particles of metal which come
Install tool no. 9998079 on the camshaft and pull it away from the hardened surface. Valve lifters and
out carefully. camshafts with minor pitting damage can be re-in-
stalled.
69
www.maskinisten.net
Repair instructions
It has been found that the damage only gets worse in

very rare cases.
Camshaft bearing,
Check the camshaft bearing surface and cam profiles replacement
for wear. The cams can be worn obliquely in the
The bearings are pressed into their locations and must
lengthwise direction, for example.
be bored after pressing in. This means that the cam-
This can be adjusted in milder cases by stoning the shaft can only be replaced in conjunction with a total
cam profile. Replace the camshaft if there is any overhaul of the engine.
other damage or wear.
When the camshaft is replaced, all the valve
lifters must be replaced at the same time.
Camshaft measurement
Oil holes in bearings
Check when you press the bearings in, that the oil
holes are centred on the corresponding oil duct in the
block.
The front camshaft bearing should be installed with
the groove aligned forwards.
Camshaft measurement
Measure the camshaft bearing surface with a mi-

crometer. The maximum wear and ovality is
0.07 mm.
The straightness of the shaft is checked by indication.
The maximum run-out in relation to the end bearings
is 0.04 mm.
Measure the lift height (cam height) with a calliper
gauge, as in the illustration above.
Lift height C = A – B (The lift height can also be mea-
sured by the “Camshaft wear check” method on page
67.
Please refer to “Technical Data” for the measurements
of the camshaft and camshaft bearings. Also, please
refer to the table on page 68 for the lift height.
70
www.maskinisten.net
Repair instructions
6
Camshaft installation
Install the valve lifter inspection hatches with new
1 gaskets.
Oil the camshaft bearing surfaces and cam profiles. Tightening torque is 24 Nm (2.4 kpm).
Carefully slide the camshaft into place, so as to avoid
NOTE! Put the oil guide plate on the rear hatch.
damaging the bearings. Use tool no. 9998079.
7
2
Install the crankcase breather pipe.
Install the camshaft flange. Torque the screws to
65 Nm (6.5 kpm).
8
3 Adjust the valve clearance in accordance with the in-
struction on page 52.
Install the timing gears in accordance with items 1–5
in the “Timing gear, assembly” method on page 65.
9
Install the timing cover and polygon hub in accor-
dance with the “Application of sealant, timing gear Install the valve covers.
cover” and “Polygon hub, installation” methods on
pages 66 and 67.
4
Oil the valve lifters and guides in the engine block Crankshaft removal
with engine oil and put the valve lifters back to their
original locations in the block.
(Engine lifted out)
NOTE! If the camshaft is new, new valve lifters must
also be installed. Coat the surface of the valve lifters 1
in contact with the cam profiles with molybdenum dis- Drain or pump out the engine oil.
ulphide compound.
2
Remove the sump. Remove the oil pump suction and
supply pipes plus the baffle.
5
Put the push rods back in their original positions and 3
install the rocker mechanism.
Remove the crankshaft pulley, torsional damper,
Tightening torque: for the 61 series with steel bearing polygon hub and timing gear cover.
caps*, the torque is 65 Nm (6.5 kpm).
Please refer to “Timing gear removal” on page 60.
Late model versions of the 61 series and all engines
in the 62 and 63 series have aluminium bearing caps.
These should be torqued to 50 Nm (5.0 kpm). 4
The 71 and 72 series should be torqued to 65 Nm (6.5 Remove the reverse gear, the flywheel and the fly-
kpm). wheel housing.
* The steel bearing cap has been replaced by an aluminium bear-
ing cap as a spare part.
5
Remove the main bearing and big end bearing caps.
(The oil pump is removed together with the front main
bearing cap).
71
www.maskinisten.net
Repair instructions
6 2
Assess any surface damage. The following applies to
nitrocarburised shafts:
Features which would be classed as dirt scratches
on an induction hardened crankshaft may be normal
surface finish on a nitrocarburised crankshaft in
some cases, as on a new crankshaft. On a used
crankshaft, this is emphasized very clearly, because
of the extremely smooth bearing surface.
After a long period of operation, very small particles
may loosen from the surface layer (spalling). This
phenomenon can be confused with dirt scratches,
but differs since the marks do not go round the entire
bearing journal, and they have uneven edges. These
defects do not need to lead to re-grinding the
crankshaft. In general, a light buffing with emery cloth
and new bearing shells is sufficient.
3
Measure the runout of the crankshaft.
Put the crankshaft on a pair of V-blocks, which are
placed beneath main bearing journals nos. 1 and 7.
Alternately, the crankshaft can be set up between a
pair of centres. Measurement should be done on the
fourth main bearing journal.
Carefully lift the crankshaft out with lifting strops and
a block and tackle. The following values apply to the measured values
(total dial gauge indication):
l < 0.2 mm: no action unless wear or surface
damage indicates re-grinding.
l 0.2 –0.7 mm: True the crankshaft carefully. Be
Inspection, crankshaft and careful to avoid over-bending.
bearings NOTE! Do not true more than absolutely necessary.
The crankshaft is nitrocarburised. A nitrocarburised l > 0.7 mm: scrap the crankshaft since there is a
shaft has greater fatigue resistance and wear damage that cracking will occur during trueing.
resistance than an induction hardened shaft. The
crankshaft must be inspected very carefully to avoid
unnecessary renovation.
Check the main bearing shells and big end bearing
shells. Change worn bearing shells or those where 4
the lead bronze lining is delaminated. Do a crack check in accordance with the instruction
After removal, clean the all the oil ducts in crankshaft below.
carefully as in the instruction, to find out whether the
crankshaft needs to be renovated.
1
Measure wear and ovality with a micrometer. The
greatest permitted ovality on main and big end
bearings journals is 0.08 mm, max. taper 0.05 mm.
Grind the crankshaft to a suitable underdimension if
these values are exceeded.
72
www.maskinisten.net
Repair instructions
Crack checking
Seizure damage can cause overheating cracks
which can only be discovered with special
equipment. Any cracks and notches are most reliably
found by magnetic powder testing such as
Magnaglo, i.e. fluorescent powder which is observed
in ultra-violet light. Please refer to the instructions
provided by the manufacturers of the equipment.
After such a test, the crankshaft must be de-fluxed.
Cracks of the following types and locations mean that

the crankshaft has to be replaced.
C. Cracks longer than 5 mm adjacent to oil duct

holes. Cracks which are shorter than 5 mm can
be ground off.
A. Lengthways cracks in bearing journals and

fillets.
D. Cracks longer than 5 mm adjacent to the marked

area. Single cracks shorter than 10 mm can be
accepted.
B. Crosswise cracks within the marked area.
73
www.maskinisten.net
Repair instructions
Crankshaft, renovation Grinding the crankshaft

It is essential for a satisfactory result from grinding,
In general, both re-grinding and trueing reduce the
that the correct method has been used. The following
fatigue resistance. So do not re-grind bearing
grinding data are recommended.
journals (nitrocarburised in particular) unless there
are strong reasons for doing so. E.g. measurement
faults (wear, ovality, taper) or so serious surface
damage that buffing is not sufficient.
Grinding wheel: Naxos 33A60 M6VK or 33A46 M6VK
If the crankshaft does not need to be re-aligned or Norton 33A60 M5VK or 23A46 M5VK.
before it is re-ground, it can be ground down to the
Diameter: New disk Ø 36"-42" (914–1067 mm). (The
second under-dimension before it has to be
disk can be used down to Ø 720 mm.)
nitrocarburised again. If the crankshaft has such
large runout that it has to be re-aligned before Peripheral speed:
grinding, it should be nitrocarburised again after Grinding wheel .................................. 28–33 m/s
grinding.
Crankshaft .................................... max. 0.25 m/s
Cooling: 3% oil emulsion (soluble). It is important that
Work order for renovation cooling is generous, preferably with oil supply from
l True the crankshaft both above and below.
NOTE! Only true the crankshaft if it is really
necessary, please refer to “Inspection, crankshaft The stone should be sharpened with a single stone
and bearings” on page 72. diamond.
l Do a crack test, please refer to “Crack checking” Peripheral feed rate ...................... 0.1 mm/revolution
on page 73.
Side feed ...................................... 0.2 mm/revolution
l Re-grind the crankshaft if necessary, please re-
fer to the next section, and do a new crack test. Depth of cut ........................................max. 0.03 mm
l Re-do the nitrocarburisation if the crankshaft has

been trued or if it has been ground to the 3rd
underdimension or more. Nitrocarburisation can
be done with gas or salt, the experience and
methods of every heat treatment craftsman are
applicable.
The following two stages are only applicable if the

crankshaft has been nitrocarburised.
l Check the runout of the crankshaft again.
l Do a new crack test.
Finish off renovation by:

l Buffing the crankshaft carefully after any grind-
ing or repeated nitrocarburisation.
l Clean the crankshaft carefully from any grinding
residue and other contamination. Rinse and
clean the oil ducts.
Crankshaft radii
74
www.maskinisten.net
Repair instructions
The surface finish (profile depth) of bearing surfaces For piston cooling, a plug* (C) must be installed
and fillets is 2 mm, medium surface deviation 5 mm. underneath the engine block in addition to the
This surface finish is achieved by buffing. Buffing is requisite nozzles, centred on the 5:th main bearing,
done in the opposite direction of rotation to grinding. plus a plug (D) on the left-hand side of the engine
l Grinding must be done in a crankcase grinding above the rear connection on the block for the flat oil
machine to an underdimension specified in the cooler.
“Technical Data” in the workshop manual. * Note. The plug on early model TAMD61 and TAMD71 (By-pass
valve on TAMD62, TAMD72 and late model versions of TAMD61
l It is very important that the fillet radii have the and TAMD71).
correct dimensions:
R = 4.2–4.4 mm (6x series)
R = 3.4–3.6 mm (7x series)
And that they have the correct shape and sur-
face finish.
Measure the radius with a radius template. The
shape must correspond with the “Crankcase ra-
dii” on page 74. Grinding steps and sharp edges
must not occur, since these could cause the
crankshaft to break.
l Special attention must be given to grinding the
centre main bearing journal, because of the
width of the locating bearing “A” in the “Crank-
shaft radii” illustration on page 74. For dimen-
sions, please refer to “Technical Data” in the
workshop manual.
NOTE! Round off sharp edges which might have

occurred by the oil duct holes when the bearing
journals were ground. Use a grinding bob or emery
cloth. Cylinder block seen from the rear
l Clean the shaft carefully from grinding residue A Distribution duct – lubrication
and other contamination. Flush and clean the oil B Distribution duct – piston cooling
ducts.
C, D Duct for oil for piston cooling
Cylinder block, inspection

Clean the cylinder block carefully and check the
bearing journals, con rods and bearing caps for
damage. Planing the cylinder block
Check that all oil ways are free from deposits and If it is necessary to plane the cylinder block, this can
that the block does not have any cracks. Small be done as long as the minimum dimensions noted
cracks can be repaired by welding when hot. If under Wear tolerances in “Technical Data” in the
welding is done to the upper plane, the block must be workshop manual are considered. The upper cylinder
planed. If there are any major defects, the block must block plane on the TAMD63 and TAMD72 must not
be replaced. be planed since the distance between the cylinder
To permit secure cleaning of the lengthwise oil ways, crowns and valve heads could be too small. The
spare part cylinder blocks are supplied without top injector nozzle tips would also come too close.
hat plugs.
NOTE! It is important that the plugs (part no. 95082- NOTE! After the upper block plane has been ground,
3) are installed once cleaning has been carried out. the piston height above the cylinder block plane must
Distribution ducts (A) and (B) must always be be checked. Max height: 0.55 mm (61 series) or 0.70
plugged at the front and rear of the engine. mm (71 series).
75
www.maskinisten.net
Repair instructions
6
Crankshaft, assembly
1
Place the bearing shells in their places.
Make sure that bearing shells of the correct
dimensions are installed and that they are correctly
seated in their places.
2
Lubricate the bearing surfaces with engine oil.
3 Lubricate the crankshaft journals with engine oil and

carefully lift the crankshaft into place, using two lifting
Check the crankshaft ducts and bearing surfaces. strops.
NOTE! Make sure that the marking on the crankshaft
gear and on the idler gear coincide.
4
Move over or install a new crankshaft gear when 7
the crankshaft is replaced. Install thrust washers for the centre main bearing
Check that the key and key slot are not damaged. (thrust bearing).
Thanks to the fixing cutouts, the thrust washers can
only be installed one way round.
8
5 Install the main bearing caps and note the markings
carefully.
The markings indicate the bearing cap positions.
9
Oil and install the main bearing cap screws. Torque
the screws to 150±10 Nm (15±1.0 kpm).
Check the end float of the crankshaft.
Maximum end float is 0.4 mm.
Set up the timing gear so that the markings on the

camshaft drive gear, injector drive gear and idler
gear coincide.
NOTE! The injector pump drive gear on the TAMD63 10
and TAMD72 does not have markings.
Install the oil pump and oil pipes.
11
Install the flywheel housing. Please refer to items 2
and 3 in the “Flange seal and flywheel housing”
method on page 83.
76
www.maskinisten.net
Repair instructions
12
Big end bearing replacement
Install a new rear crankshaft seal. Please refer to
items 2 and 3 in the “Crankshaft seal, rear” method
(Crankshaft not removed)
on page 83.
Preparatory work
l Drain or pump out the engine oil.
l Remove the sump.
13 l Remove the supply and suction pipes for the oil
Clean the mating surface of the flywheel against the pump, plus the baffle.
crankshaft flange and install the flywheel. Torque the l Remove the injectors, to make it easier to crank
screws to 190 ± 10 Nm (19 ± 1.0 kpm). the engine.
1
14 Turn the crankshaft round until the bearing caps for
Install the timing gear cover with a new string of seal- cylinders 1 and 6 come into the positions where the
ant. Please refer to the “Application of sealant, timing screws can be removed.
gear cover” method on page 66.
2
Remove the bearing caps for con rods 1 and 6.
15 NOTE! Make sure that you do not mix up bearing
Install the polygon hub, torsional damper and crank- caps nos. 1 and 6.
case pulley. Please refer to the “Polygon hub, instal-
lation” method on page 67.
3
Remove the bearing shells and clean the bearing lo-
cations in the con rods and bearing caps.
16 4
Install the big end bearing caps, be careful with the Check the bearing journals and bearing shells for
markings. damage.
The markings specify the location of each bearing If the bearing shells have seized, the reason must be
cap. investigated before new bearing shells are installed.
17 5
Torque the bearing cap screws to 190 ± 10 Nm Check measure the bearing journals with a microme-
(19 ± 1.0 kpm). ter which covers the range of 50–75 mm.
Max permitted ovality 0.08 mm
18 Max permitted taper 0.05 mm.
Install the sump and tighten the screws. If any values exceed the permitted limits, the crank-
shaft must be removed and repaired.
Please refer to the tightening sequence for each
engine in “Technical Data” in the workshop manual, NOTE! Check “Technical Data” in the workshop
under the “Tightening torque” heading. manual to see whether the crankshaft journals have
standard or underdimensions.
19
Check the injector settings and adjust if necessary.
77
www.maskinisten.net
Repair instructions
6
Main bearings, replacement
(Crankshaft not removed)
Preparatory work
l Drain or pump out the engine oil.
l Remove the sump.
l Remove the supply and suction pipes for the oil
pump, plus the baffle.
l Remove the injectors, to make it easier to crank
the engine.
1
Remove the main bearing cap screws for the front
Install new bearing shells. Make sure that the guide main bearing cap (the front main bearing cap is un-
pin on the bearing shell is correctly located in the done together with the oil pump).
cutouts in the con rod and bearing cap, and that the
oil holes in the con rods and bearing shells line up.
NOTE! Check “Specifications” in the workshop
manual to ensure that the bearing shells have the
2
correct dimension.
7
Oil the bearing shells and bearing journals with en-
gine oil. Install the bearing caps in accordance with
the markings and torque the screws to 190 ± 10 Nm
(19 ± 1.0 kpm).
8
Turn the crankshaft until con rods nos. 2 and 5 come
into position, and repeat items 2–7.
9
Turn the crankshaft until con rods nos. 3 and 4 come Turn the crankshaft until the oil hole is free. Put a pin
into position, and repeat items 2–7. in the oil supply hole. The pin should be of such a
length that it just pulls the upper bearing shell round
After you have changed all the big end bearing
when the crankshaft is turned.
shells, turn the crankcase and check that no bearings
run stiff. The bearing shell has a heel pressed out which en-
gages in a cutout in the bearing seat in the crank-
case. This heel means that the crankshaft must be
rotated in the direction of rotation of the engine
(clockwise) when the bearing shell is rolled out.
78
www.maskinisten.net
Repair instructions
3 7
Clean and check the bearing seat, bearing cap, Change the other main bearing shells, one at a time,
bearing journal and bearing shells for damage. If in the same way as the first one. After you have
the bearing shells have seized, the reason must be changed each main bearing, check that the crank-
investigated before new bearing shells are installed. shaft turns easily, by cranking the shaft.
If wear is heavy, or if you suspect that ovality could
be excessive, the crankshaft must be removed for
measurement if you do not have access to crank-
shaft measuring equipment.
8
4
Check that you have obtained the correct bearing di-
mension when you replace the bearing shells.
NOTE! If you are at all uncertain, check “Specifica-
tions” in the workshop manual to see the overdimen-
sions which can occur.
5
Oil the bearing journals and the new bearing shells.
The thrust bearing for the crankshaft is located in

milled grooves in the centre main bearing position.
Check the end float of the crankshaft and replace the
thrust washers if the end float is excessive or if the
washers are damaged. Thrust washers are available
in a large number of overdimensions, please refer to
“Technical data” in the workshop manual.
The end float must not exceed 0.40 mm.
NOTE! When selecting thrust washers, make sure
that the end float is at least 0.16 mm.
The upper bearing shell is installed by turning the

crankcase the opposite way to the normal direc-
tion of rotation, with the pin in the hole. Check that
the pressed out heel in the bearing shell engages
correctly in the cutout in the bearing seat. Remove
the pin from the oil hole and install the cap with a
new bearing shell.
Torque the screws to 150 ± 10 Nm (15 ± 1.0 kpm).
79
www.maskinisten.net
Repair instructions
9
Flywheel, replacement
1
Use a narrow wood or plastic pin to remove the

thrust washers. Remove the screws and lift the flywheel away.
Flywheel, inspection
10
Check the flywheel for cracks and other damage.
When all the main bearing caps have been torqued, Also check that the gear ring is not worn or dam-
check the crankshaft end float. The end float, meas- aged. Replace the flywheel and gear ring as neces-
ured with a dial gauge, must be 0.16–0.40 mm. sary.
2
11
Clean the mating surface of the crankshaft flange
Install the oil pump and injectors.
against the flywheel.
3
Clean the mating surface of the flywheel against the
crankshaft flange.
4
Check that the flywheel location dowel in the crank-
shaft is in place and is undamaged.
5
Lift the flywheel into place and install the screws.
6
Torque the flywheel screws to 190 ± 10 Nm (19 ± 1.0
kpm).
80
www.maskinisten.net
Repair instructions
4
Gear ring, replacement
(Flywheel removed)
Put the heated gear ring on the flywheel and tap it

into place with a soft punch and hammer.
Drill 1–2 holes in the gap between two teeth on the Allow the gear ring to air cool.
gear ring.
Split the gear ring across the drilled holes, using a
hammer and cold chisel.
2 5
Brush the mating surface of the flywheel with a wire Clean the mating surfaces on the flywheel and crank-
brush. shaft. Check the location dowel in the crankshaft
flange and the rear crankshaft seal. Replace
if necessary.
Install the flywheel. Tightening torque is 190 ± 10 Nm
(19 ± 1.0 kpm).
3
Heat up the new gear ring in an oven, or with a weld-

ing torch, to max 180–200°C.
WARNING. If you use a welding torch, take

great care to ensure that the gear ring is evenly
heated, and not spot heated, which would
cause annealing. To check the heating
process, polish the gear ring bright at several
places before heating it. Stop heating when
these surfaces become blued.
81
www.maskinisten.net
Repair instructions
Flywheel, indication Read off the value, and move the dial gauge with
base round to the opposite side of the flywheel.
Special tools: 9999696, 9989876 The value of these measurements must not exceed
0.15 mm.
1
Place a dial indicator with its tip on the flywheel.
2
Zero the dial gauge. Turn the flywheel round and
read off the greatest value.
The measured value must not exceed 0.15 mm, at a Put the magnetic base of the dial gauge on the fly-
measurement radius of 150 mm. wheel, and put the tip of the dial gauge on the inner
If the flywheel is more skewed, remove the flywheel edge of the flywheel housing (see illustration). Pull
and check whether there is dirt or unevenness be- the flywheel round and read off the indication.
tween the flywheel and the crankshaft flange. Centring of the inner edge of the flywheel housing,
relative to the flywheel, must be within 0.25 mm.
If any of the values should exceed 0.25 mm, the lo-
cation of the flywheel housing against the engine
block should be checked.
Flywheel housing, indication

Special tools: 9999696, 9989876
Put the magnetic base of the dial gauge on the fly-

wheel, and put the tip of the dial gauge on the outer
edge of the flywheel housing (see illustration).
82
www.maskinisten.net
Repair instructions
Crankshaft seal, rear, Flange seal, flywheel housing,

replacement replacement
(Flywheel removed) (Flywheel removed)
Special tools: 9992000, 9996437
1 1
Remove the four rear screws from the sump, and the
screws which hold the flywheel housing to the cylin-
der block (10 no.)
Tap the flywheel housing loose, using a plastic faced
hammer, by tapping alternately on the right and left
hand sides.
Tap in one side of the oil seal with a narrow punch.

The other side will then be pressed out and the oil
seal can be extracted by means of a wire hook (illus-
tration), or poked out with a small screwdriver.
2
Clean the mating surface in the flywheel housing and
on the crankshaft.
Oil in the inner edge of the new oil seal with engine
oil. Put some sealant, such as Permatex® No. 3 on
the outside of the oil seal.
2
Clean the mating surfaces of the flywheel housing
and cylinder block
Apply an even string (Ø 2 mm) of sealant, Volvo
Penta no. 1161231-4 to the mating surface of the fly-
wheel housing. Install the flywheel housing within
20 minutes after applying the sealant.
3
Install and torque the flywheel housing screws to
140 Nm (14 kpm).
Tap the oil seal in carefully, using mandrel no.
9996437 and shaft 9992000. Install and torque the sump screws to 24 Nm (2.4
kpm).
Install the flywheel. Tightening torque is 190 ± 10 Nm
(19 ± 1.0 kpm).
83
www.maskinisten.net
References to Service Bulletins
Group No. Date Concerning
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
84
www.maskinisten.net
Report form
Do you have any complaints or other comments about this manual. Please make
a copy of this page, write your comments down and send them to us. The ad-
dress is at the bottom. We would prefer you to write in English or Swedish.
From: ............................................................................
......................................................................................
......................................................................................
......................................................................................
Refers to publication: .............................................................................................................................................
Publication No.: ............................................................. Date of issue: .................................................................
Proposal/motivation: ..............................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
Date: ................................................................
Signed: .............................................................
AB Volvo Penta
Technical Information
Dept. 42200
SE-405 08 Göteborg
Sweden
www.maskinisten.net
7735718-4 English 08–1996

Volvo-Penta Tamd61a-Tamd72wja Workshopmanual Sec Wat

Uploaded by

Copyright:

Available Formats

Volvo-Penta Tamd61a-Tamd72wja Workshopmanual Sec Wat

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Volvo-Penta Tamd61a-Tamd72wja Workshopmanual Sec Wat

Uploaded by

Copyright:

Available Formats

www.maskinisten.

TAMD61A, TAMD62A, TAMD63L-A, TAMD63P-A

Group 21 Engine body

personal injury. Avoid burns. Take precautions

Engine with turbocharger: Never start the engine

Important Never use start spray or similar to start the engi-

Do not disturb battery connections when starting

Clutch adjustments must be carried out with the

About the service manual Certified engines

In order to conduct satisfactory service work it is

l Always use gloves made of chloroprene rubber

9996421 9996433 9996437 9996643

9996400 9996402 9996419 9996420

9996650 9996651 9996657 9996662 9996645

9996841 9996842 9996847

9996852 9996855 9996861 9996867 9998009 9998070 9998079 9998115

Other special equipment

885126 9988539 9989876 9999696

Other special equipment

Design and function

Design and function

Design differences, engine l New sea water pump

Design and function

TAMD72A – TAMD72WJ-A l Electronic box (EDC) added, located beside the

Location of type approval

Design and function

1 Junction box with circuit breakers 8 Oil cooler, reverse gear

Design and function

1 Air filter 8 Lubrication oil filter (alt. location at left-hand rear

Design and function

1 Filter for crankcase breather 8 Alternator

Design and function

1 Junction box with circuit breakers 7 Turbocharger

Design and function

Design and function

1 Air filter 7 Lubrication oil filter (alt. location at left-hand rear

Design and function

Design and function

1 Air filter 7 Lubrication oil filter, engine (alt. location at left-

Design and function

Design and function

Four rubber O-rings are used to seal the cylinder

Note. There have been two previous versions of the

WARNING! Special safety rules apply to fluoro-

Design and function

* TAMD63: The white paint spot on the spring should be visible

Gudgeon pin hole with “side relief”

Design and function

* The pistons on the later version still have 4 piston ring

Design and function

Crankshaft with con rods and pistons

Big and small end bearings

Design and function

Con rods with trapezoid small end (71 and 72 series).

General Measures before renovation outside the

Engine stand attachment

1 M8x30 mm 4 M10x30 mm [6(x) series]

Condition test, engine Cylinder head, renovation

Compression test Cylinder head, removal