433(S) September 2021 MICROPROCESSOR & MICROCONTROLLER ‘Time Allowed: 1.5 Hours Full Marks: 70 Answer to Question No.1 is compulsory and Answer any two questions from the rest. Answer the following questions (any twenty): 20x2 1) Addressing mode of instruction HLT is ~ a) immediate, b) direct, c) indirect, d) Implied. ii) How isthe s MVIA,I80 ADD A,19q a) AC=0, P=0, b) AC=0, P=1, ¢) AC=1, P=0, d) AC=1, P=1 tus of auxiliary carry and parity flag affected if write instruction? iif) OBB is — a) 8 bit microprocessor, b) 16 bit microprocessor, c) 32 bit microprocessor, 4) 64 bit microprocessor iy) Result of ‘MUL AB” stores in — a) B (Higher Byte) and A (Lower Byte), b) A.) A (Higher Byte) and B (Lower Byte), d) B. v) How many clock cycles are required to complete an opcode fetch operation in 8085? ~ a) Five, ) Two, c) Three, 4) Four. vi) If we push data onto the stack then the stack pointer ~ a) increases with every push, b) decreases with every push, c) none of the mentioned, d) both of the mentioned. vil) Instructions JZ, INZ, JC and INC monitor the bits of which register? —a) A, b) B,) C, d) Flag. viii) Which instructions have no effect on the Flag registers? — a) ANA, b) ORA, c) XRA, d) all of the mentioned. htips://www.whscteonline.com ix) When the micro controller executes some arithmetic operations, then the flag bits of which register are affected” — a) PSW, b) SP, c) DPTR, ) PC. x) To initialize any port of 8051 as an output port what value is to be given to it? — a) OxFF, b) 0x00, €) 0x01, d) A port is by default an output port. xi) Which one is the Special Function Register? — a) RO, b) TMOD, c) R1, d) None. xii) In case of ‘VO mapped 1/0", accessing of 1/0 devices is done by — a) LDA and ST'A instructions, ) IN and OUT instructions, ¢) PUSH and POP instructions, d) None of these. xiii) DMA controller is used to ~ a) data transfer between memory and I/O devices, b) data transfer between memory and microprocessor, c) data transfer between microprocessor and /O devices, d) All of these. xiv) When numbers are added or subtracted, an overflow may occur ~ a) odd, b) unsigned, ©) even, d) signed xv) Length of the instruction queue in 8086 is — a) six bytes long, b) seven bytes long, c) eight bytes Jong, d) ten bytes long, xvi) PC in 8085 is similar to — a) PSW in 8051, b) SP in 8051, c) IP in 8051, d) DPTR in 8051 https://www.wbscteonline.comRp xvii) ‘The pin MN/MX of 8086 is grounded for — a) minimum mode operation, b) maximum mode operation, c) min-max mode operation, d) max-min mode operation. xviii) How many 16 bit register does 8086 have? —a) 8, b) 9.) 14, d) 13. xix) Which one is more accurate answer for Program Counter (PC)? — a) PC holds address of Instruction, b) PC is incremented by one after execution of instruction, c) PC is decremented by one after execution of instruction, d) (a) and (b) xx) Data and Address bus are de-multiplexed by ~ a) ALE signal, b) READY signal, c) RESET signal, 4) None of these. xxi) Direction of signal flow for Address bus and data bus arc — a) Unidirectional and Bidirectional respectively, b) Bidirectional and Unidirectional respectively, ¢) Unidirectional for both, d) Bidirectional for both. xxii) In which case, status signals become So = 1 and S; = 1? ~ a) opcode fetch, b) memory read, ©) memory write, d) halt. xxiii) Microprocessor is used in— a) Desktop, b) Laptop, c) Server Computer, d) All of these. xxiv) _Is this possible to write a program of two 64 bit numbers addition in 8 bit microprocessor? - a) No, b) Yes, c) Possible, if and only if memory space is increased, d) Possible, if and only if clock frequency is increased. 4) Draw timing diagram for VO read operation, b) What are the various registers of 8085? 1045 a) Write an assembly language program add two 8-bit numbers, the sum may be of 16 bits b) Discuss the addressing mode of 8086. 748 Write short notes on the followings: 75x2 a) DMA controller ») Interrupts a) Draw pin diagram of 8085 and explain each pin. b) Compare between 8085 and 8086 1045 a) What is memory mapped 1/0? How it differs from VO mapped VO? b) Describe programming model of 8251. 148 a) Draw the block diagram of Intel 8086 And discuss different blocks. b) What is m/e cycle? How itis related with instruction cycle? 87 4) Write some application of microcontroller? b) Describe programming of 8051, 5410 https://www.wbscteonline.com Whatsapp @ 9300930012 Send your old paper & get 10/- wae GAT ee srt ste 10 wad oA, Paytm or Google Pay & https://www.wbscteonline.com