Scribd
Upload
17 views3 pages

Ranger

Ranger

Uploaded by

qlilov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
17 views3 pages

Ranger

Ranger

Uploaded by

qlilov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 3

CLUTCH FLUID, CLUTCH PEDAL

1.Repeat steps 4 and 5 until only clean fluid is seen. CLUTCH PEDAL
2.Tighten the bleeder screw.
CLUTCH PEDAL INSPECTION/ADJUSTMENT
Tightening torque 5.9—8.8 Nm {60—90 kgf Clutch Pedal Height
cm, 52—78 inlbf} 1. Measure the distance from the upper surface of the
pedal pad to the carpet.
3.Add fluid to the MAX mark.
4.Check for correct clutch operation. Pedal height 241.6—246.6 mm
{9.52—9.70 in}

A 14—17
{1.4—1.8, 11—13}

PEDAL HEIGHT

a< ——»
CARPET

N-m {kgf-m, ft-lbf}

2.If necessary, adjust the pedal height by turning


stopper bolt A and clutch switch (or adjust bolt) B.
H-2
CLUTCH PEDAL

Clutch Pedal Free Play CLUTCH PEDAL REMOVAL/INSTALLATION


1. Depress the clutch pedal by hand until clutch 1. Disconnect the negative battery cable.
resistance is felt, and measure the pedal free play. 2.Remove in the order indicated in the table.
3.Install in the reverse order of removal.
Pedal free play 3.0—8.0 mm 4.After installation, adjust the clutch pedal.
{0.12—0.31 in} (Refer to CLUTCH PEDAL
INSPECTION/ADJUSTMENT)

L.H.D.
19—25
6.9—9.80
N-m N-m
{kgf-m, {70—
ft-lbf}
100 ®
{1.9—2.6,
kgf-cm, 61— <$>-------@
14—18}
86.8
19—25in-lbf}
{1.9—2.6,
14—18}

N-m {kgf-m, ft-lbf}

2.If necessary, adjust the pedal free play by turning


locknut C and adjusting push rod D.

Clutch Release Point Inspection


1. Without depressing the clutch pedal, slowly shift the
shift lever into reverse position until the gears contact. 1 Clutch switch connector (G6, F2 CIS)
2.Gradually depress the clutch pedal and measure the
2 Spring pin
stroke distance from the point the gear noise stops
(release point) up to the full stroke end position. 3 Clevis pin
FULL 4 Nut
STROKE
END 5 Clutch pedal component
POSITION
R.H.D.
G6, F2 CIS, F2 Carb
• Refer to section F1, F3, or F4, INTAKE-AIR
SYSTEM, ACCELERATOR PEDAL
REMOVAL/INSTALLATION.

WL, WL Turbo
• Refer to section F2, INTAKE-AIR SYSTEM,
Standard distance A: 14.6—37.5 mm ACCELERATOR PEDAL
{0.58—1.47 in} (reference value) REMOVAL/INSTALLATION.

3.If the clutch pedal disengagement stroke is outside of


the specification, adjust the pedal height and pedal
free play, and verify the pedal stroke.

Pedal stroke 146.5—151.5 mm


{5.8—5.9 in} (reference value)

H-3

You might also like