Gas Turbine Gen
Gas Turbine Gen
Gas Turbine Gen
THERMOCOUPLES
(EGT)
NHP
1
NHP
2
NHP
3 GENERATOR
NST STARTER
PCD
F WT
E
IGV RAM E
D
B
HYDRAULIC A
POWER C
UNIT SERVO K
VALVE
SERVO
CONTROLLER
I/E
BYPASS
VALVE
GAS LIQUID
FUEL FUEL
SPEED STOP GAS FUEL STOP
FUEL
RATIO VALVE CONTROL VALVE
PUMP
VALVE FUEL VALVE
FLOW
DIVIDER
4-20 mA 4-20 mA
FUEL PRESSURE INPUT LIQUID FUEL FLOW INPUT
4-20 mA 4-20 mA
SRV OUTPUT LCV VALVE OUTPUT
4-20 mA 4-20 mA
FCV OUTPUT WATTS INPUT
4-20 mA mV
IGV OUTPUT THERMOCOUPLE INPUT (EGT)
4-20 mA
PCD INPUT
FREQUENCY
NST INPUT OPTIONAL
FREQUENCY MMI
Simplified schematic showing a Petrotech advanced PLC-based integrated gas turbine control system for
a generator set. The system provides turbine fuel control, temperature control, sequencing/protection,
communication interfaces, and more.
PRODUCT BULLETIN 96053 - GAS TURBINE CONTROLS FOR GENERATOR DRIVE APPLICATIONS - Page 2
APPLICATION
The Petrotech integrated control system provides cost-effective
complete or partial control system retrofits for gas turbine driven
generator packages. The system provides replacement controls for
outdated electro-hydraulic and analog-electronic controls. The
PLC-based system can include turbine and generator sequencing,
complete turbine control, load control, DCS interface, and a graphic
operator interface for system status, trending, and data logging.
ADVANTAGES
• Integrated control capability:
Turbine fuel control and sequencing/protection are integrated into
a single platform. This eliminates the need for additional hardware
and communication links, thereby providing a less complicated, more
cost-effective solution.
• Fault tolerant:
Control package is available on fault tolerant controllers for critical
control applications.
• Reliability:
ALL control functions are performed by tested and proven industrial
PLC equipment, not by MS-DOS based computer equipment which is
not designed to function as a “controller”.
• Non-proprietary interfaces:
Interfaces in the form of 4-20 mA, RTD, frequency, thermocouple,
and dry contact I/O allow simple integration into existing sequence/
protection logic controller, making very low-cost partial control
upgrades simple and practical.
• Fail-safe features:
Redundant overspeeds; open/short monitoring of mA and
thermocouples; readback monitoring of outputs, and special self-
check features improve safety.
Replacement controls for two Allison 501K gen sets in emergency
backup power service.
PRODUCT BULLETIN 96053 - GAS TURBINE CONTROLS FOR GENERATOR DRIVE APPLICATIONS - Page 3
• Improved operator information with optional MMI: Man-machine interface (MMI), alphanumeric display (low end)
Industrial workstation graphically displays start-up sequencing, plus panel meters for NHP, NLP, and EGT:
speeds, temperatures, operating points, and alarm/shutdown status. • NEMATRON.
Data logging and trending can be used as part of a preventative • CTI Access 4000.
maintenance program.
• Allen-Bradley Redi-Panel.
• Simple installation: • Customer specified.
A dimensionally identical replacement of the control panel is
Man-machine interface (MMI), graphic display (high end):
possible, saving substantial architectural and installation cost. Control
• MMI Hardware:
panels can be installed one at a time allowing other units to continue
operating. Intecolor industrial computer and monitor.
IBM industrial computer and monitor.
• Rugged:
Texas Microsystems industrial computer and monitor.
Control panels can be built Division 2, Nema 4X for installation in
harsh local environments. XYCOM industrial computer and monitor.
Nortech industrial computer and monitor.
• Flexibility:
NEMATRON industrial computer and monitor.
The control system package can accommodate many different
control strategies based on the customer’s need and budget. Customer specified.
• MMI Software:
CONTROLLERS/SPECIAL FEATURES Wonderware InTouch.
The gas turbine generator application control package typically Citech.
includes: Intellution.
• Firing (soft lightoff) ramp. Realflex.
• Start-up controller. Customer specified.
• NHP controller.
Critical function redundancy for fail-safe action:
• NHP acceleration and deceleration scheduling.
• Customer specified shutdowns in addition to NHP, NLP, EGT, and low
• EGT controller. lube oil pressure.
• EGT rate of rise controller.
Communication interface for DCS or SCADA:
• EGT controller for inlet guide vanes (if applicable). • MODBUS.
• Isochronous load sharing. • Ethernet
• Combustion monitoring system with automatic rejection of failed • Customer specified.
thermocouples.
Type of control panel enclosure:
• Cooldown stop.
• Front and back plate for existing control enclosure (common for
• Dual fuel capability with bumpless on-line transfer.
some GE gas turbine retrofits).
CUSTOMER SELECTABLE COMPONENTS FOR THE • Custom fabricated new control enclosure.
CONTROL SYSTEM • Class I, Division II stainless steel purged panel enclosure for
hazardous locations.
Advanced Programmable Controller:
• Standard Rittal type panel enclosures.
• Siemens/TI 505.
• Allen-Bradley Series 5, Flex I/O, ControlLogix.
• GE Fanuc 90-70 and 90-30
• Modicon Quantum.
Application control package:
• Petrotech gas turbine control.
• Petrotech sequencing and protection.
• Vibration Monitor:
• Bently Nevada 3300, 3500, and 2201 (for Allen-Bradley systems only).
• Vibrometer.
• Metrix.
• Vibrotec.
• Customer specified.
Autosynchronizer:
• Basler.
• General Electric.
• Customer specified.
Replacement controls for one GE LM2500 gen set in LNG plant power service.
PRODUCT BULLETIN 96053 - GAS TURBINE CONTROLS FOR GENERATOR DRIVE APPLICATIONS - Page 4
This document is a Petrotech, Inc. copyrighted intellectual property and may be changed at any time without notice.