A1100 A1200 A1300

Quick Start Guide

Regulatory models W2100 and W2106

 Please read the safety instructions booklet before setting up
the projector.

Unpack the box

1 Here's what's included:

Projector Remote

USB Cable Computer Cable Power Cable

Save the box and packing materials.

Put batteries in the remote

2 The remote uses 2 AA batteries.
1 2 +
-
+ 3

Please dispose of batteries in an environmentally proper manner.

Status Indicator Panel Power/Standby Service Required

The top of your projector includes a

convenient indicator panel with symbols that
light up to show important status.
For details, see Troubleshooting. High Temperature Replace Lamp
 Connect source
3 Color-coded connections make it easy.
You can connect more than one source if needed.

Connect to: Computer Got an Apple computer?

Computer Cable (included) You may need an adapter. For more
information, see How-To Guides at
USB Cable (included) www.infocus.com/support/howto
USB is optional
USB connection only needed for:
Presentation control using
projector remote
Upgrading projector firmware
Computer

OR

Connect to: DVD or VCR* (using optional cables)

1 Connect video using either an S-Video or a Composite Video cable

2 Connect audio using a Mini-Plug to RCA Audio Y-Cable

Composite Video Cable 

 Good
OR
S-Video Cable  Better


Mini-Plug Audio Y-Cable

L R
Audio Out Video Out

DVD or VCR

*Also for game console or cable box.

RCA Audio Cable To Projector
Want better sound? or

Connect the source's audio output to a

receiver/amplifier or home theater L
Audio In
R L R
Audio Out Video Out
system with separate speakers. Home Theater or Receiver DVD or VCR

OR
Connect to: Other kinds of sources
How-To Guides are available at www.infocus.com/support/howto
4 Turn on projector and source
1 Connect the power cord to the projector
and to an electrical outlet
The power light on the projector will light amber.

2 Remove the lens cap

3 Turn on the projector

Press power (on the projector or remote).
The power light will start blinking green.

4 Wait for the lamp to warm up

After a few seconds, the power light will stop blinking and turn
green. It can take a minute for the lamp to reach full brightness.
5-10 sec.
Warning: Do not look directly into the lens
when the projector is turned on.

5 Turn on computer or other source

You may need to press a specific key combination to activate
your laptop's external video port. On most laptops, hold down
the FN key while pressing a key labeled CRT/LCD, LCD/VGA,
a monitor icon , or similar. Key combos for popular models:
Apple F7 Gateway Fn+F3 or Fn+F4 IBM ThinkPad Fn+F7
Dell Fn+F8 HP/Compaq Fn+F4 or Fn+F6 Toshiba Fn+F5
Fujitsu Fn+F10 Sony Fn+F7

Important: If there is still no video, restart your

i computer (first make sure it's connected to the
source projector and the projector is turned on).

6 Change source if needed

If needed, press source (on the projector or remote) to view the
source. You may have to press it more than once.
 5 Adjust the picture

1 Height Projector Location

As distance increases, the

image gets larger and
1
moves upwards.
2
1 Hold down the release button
under the front of the projector.
2 Lift the front of the projector to
the desired height.
3 Release the button. Lens center line

2 Keystone
Diagonal
Screen Size
Distance to Screen
Minimum Maximum
60" / 1.5m 7'6" / 2.3m 8'6" / 2.6m
80" / 2m 10'2" / 3.1m 11'6" / 3.5m
92" / 2.3m 11'10" / 3.6m 13'1" / 4.0m
150" / 3.8m 19'4" / 5.9m 21'8" / 6.6m

Press the keystone buttons to

make the picture square.

Interactive Screen Size and

3 Zoom and focus

Distance Calculator
www.askproxima.com/calculator

Zoom
(rear)

focus
(front)
Ceiling mount?
To flip the image, turn on the Ceiling
Adjust zoom first, then focus the
Mount setting in the Setup menu.
center of the image.
 Using the menus
1 Press menu, then press or to review menus.
2 Press select to enter a menu, then press or to review settings.
3 Press select to change a setting. If this shows more choices, press
or to update the setting, then press select or menu to save it.
4 Press menu to go back. Press it again to remove the menu.
Note: Most picture settings are disabled (gray) unless a source is being displayed.

Controlling your presentations

Connect the USB cable between the projector and your computer (see step 3 ),
then press and to move through your presentation slides.

6 Turn off the projector

Press the power button
The power light on the projector will blink while the fan cools
the lamp. If you need to unplug the projector, wait until the
fan stops and the power light stops blinking and stays on.

Note: While the power light is blinking, button presses on the

projector and remote are ignored.

7 Register your product

Activate your warranty to ensure eligibility for service and support.
Get special offers and notifications about free product updates.

1 Write down your projector's serial number

It's printed on the label on the back of the projector. You'll need it to register (and if
you ever need to contact support).

Serial number:

2 Go to www.askproxima.com/register

8
Optional: Read the Reference Guide
Download it at www.askproxima.com/support
The Reference Guide is available in multiple languages. It covers advanced setup and
operation, including lamp replacement instructions.
Troubleshooting
If there is no picture or the picture is blank
If the power light is off, make sure the power cord is connected and plugged
into a live electrical outlet. If the power light is amber and not blinking, press
the power button.
Check video source and cables. Make sure the video source (computer, DVD
player, VCR, etc.) is turned on and cables are securely connected between the
source and the projector.
Make sure your computer's video port is enabled. Press the key combination
that activates your laptop's external video port (see step 4 ). If there is still no
source
image, restart your laptop.
Press the Source button. You may need to press it several times to view the
correct source.
Press the Auto Image button.

If "Signal out of range" is shown, or the picture looks bad

Press the Auto Image button. If that doesn't help (and the source is a computer),
reduce your computer's display resolution or vertical refresh rate.

If the replace lamp light is on

Turn the projector off and wait at least one minute, then turn it on again. If the
replace lamp light turns on again, the lamp needs to be replaced. For lamp
replacement instructions, see the Reference Guide, which can be downloaded at
www.askproxima.com/support
Only InFocus genuine lamps are tested for use in this projector.

If the high temperature light is on

Turn the projector off and remove anything that may be blocking the air vents
on its side. Leave the projector off for at least one minute to let it cool before
turning it on again. Important: Continuous operation at high temperature may
reduce the lifetime of the lamp and/or projector.

If the service required light is on

Turn the projector off and wait at least one minute, then turn it on again. If the
service required light turns on again, the projector needs to be serviced. See
below for service contact information.

More troubleshooting options are in the Reference Guide

Download it at www.askproxima.com/support

Warning: In the unlikely event of a lamp rupture, particles may be ejected from the projector.
Keep out of the area under and around the projector when it is turned on. See the safety
instructions booklet for more details.
 Questions? We’re here to help!
Visit us at:
www.askproxima.com/support
We’re here to support you with your new purchase. We can help you with…
• Determining screen sizes
• Documentation in other languages
• Connecting your sources (TV, DVD, Cable/Satellite, Game, etc.)
• Selecting optional accessories
• Product warranty protection plans

USA, Canada, Latin America Asia Pacific Europe, Middle East, Africa
Customer Support Telephone Customer Support Telephone Customer Support Telephone
+1 (503) 685-8888 Singapore: +65 63539449 +31 (0)36 539 2820
TOLL FREE: 800-799-9911 China: 800.828.2268 Mon-Fri, 08:30 - 18:00 CET
Mon-Fri, 7 am - 5 pm Pacific Australia: 1300-725-295 [email protected]
[email protected] Australia Direct Sales: 1800-885-841
Mon-Fri, 9 am - 5 pm SGT
[email protected]

Hg - Lamp contains mercury. Manage in accordance with local disposal laws.

See www.lamprecycle.org
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070-8238 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conforms to the following directives and norms: EMC Directive
2004/108/EC, EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3, Low Voltage Directive 2006/95/EC, Safety: IEC 60950-1:1st
Edition.

Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered
trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of
Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP
logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and
INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

FCC Warning
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment that are not expressly approved by InFocus Corp. may void the user’s authority to operate
the equipment.

Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product certification label.

Input ratings: 100-240Vac, 3.0A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.