859 June 2022 307/4(N)

cOMPUTER SYSTEM ORGANiZATION

Time Allowed: 3 Hours Full Marks: 60
Answer the following questions from Group-A, B & C as directed.

GROUP-A
1. Choose the correct alternative (Any ten) 1x 10=100

i) The numbersuccessful accesses to memory stated as a fraction is called as

a) Access rate b) Success rate c) Hit rate d) Miss rate
i) The final addition sum of the numbers, 0110 & 0110 is_
a) 1101 b) 1111 e1001 d) 1010

ii) What does CSA stands for? a) Computer Service Architecture b) Computer Speed Addition c) Carry
Save Addition d) None of these

iv) Individual control word of the micro routine are called as- a) Micro task b)Micro instruction c)Micro
operation d)Micro Command

v) Which of the following circuit convert the binary data into a decimal? a) Decoder b) Encoder c) Code
converter d) Multiplexer

vi) The situation wherein the data of operands are not available is called a Data hazard b) Stock
c) Deadlock d) Structural hazard

vii) What is the full form of CISC? a) Complex Instruction Sequential Compilation b) Complete
Instruction Sequential Compilation c) Computer Integrated Sequential Compiler d) Complex Instruction
Set Computer

vii) The alternate way of writing the instruction, ADD #5,R1 is-a) ADD [5).[RI]; b) ADDI 5,R1;
c) ADDIME 5,[R1}: d) There is no other way

ix) In order to read multiple bytes of a row at the same time, we make use of-

a) Memory extension b}Cache c) Shift register d) Latch

x) implemented using.
In full adders the sum circuit is
a) And & or gates b) NAND gate c) XOR d) XNOR
Bidirectional c) Multidirectional d) None of the
xi) Computer address bus is_. a) Unidirectional b)
above
connects the CPU to
memorya on the
system board?
xii) Which of the following computer bus the above
bus d) None of
a) Expansion bus b) Width bu_c)System
an input port and writing an output port respectively are -

xiii) The instructions that are used for reading OUT

MOV, XCHG, b) MOV, IN, c) IN, MOV, d) IN,
Rl-R2 b) R1+R2 c) Both d) None
Xiv) Micro operation is shown as: -

a)

1
 Xv) An interrupt that
a
can be temporarily ignored is-
Vectored interrupt b) Non-maskable interrupt c) Maskable interrupt d) High priority interrupt

2. Fill in the blanks Ix 10=10

(Any ten):
i)
is used to store data, instructions and results permanently for future use.
ii) is gencrally used to increase the apparent size of physical memory.
in) Gray Code is also called as
IV) Instruction register stores_
v)A high speed memory is placedbetween the CPU and the primary memory 15 knowna

vi) 1/O address in 8086 is bit.

into the physical memory when they
Vil) iechniques that automatically move programs and data blocks
are required for execution are called
viii) Hit ratio is maximum in mapping
is
ix) The bias value for single-precision floating point numbers
addressing mode.
x) MOV AX. [2A50] is an example of
xi) Loop unrolling is a technique to improve
xii) Page table resides in
xiii) Microinstruction consists of
xiv) The smallest entity of memory is called
XV) A source program is usually in language.
1x 10 =10
3. Answer the following question (any ten)
units?
i) How control unit controls other
and 32 bit microprocessor.
j
Give an example of a 4 bit, 8bit, 16- ,

iii) What is Bus?

MAR and MDR?
iy What is
v) What is register?
vi) What is interrupt?
vii) What is non-volatile memory?
address?
vii) What is logical
code?
ix) Which is an error-detecting
shift?
x) What is the logic into form that is intelligible to
the user?
converts digital signal a
xi) What type of device which is required to start a computer?
Which memory stores instruction
xii)
xiii) Define clock rate.

xiv) What is the RAID system?

GROUP-B
2x6 12
4. Answer the questions (Any six)
unit?
main elements of the control
What are the three
jWhat is Cache memory? address?
T What is control memory
iv) What is the 2's complement representation of -6?
in COA?
v) What is clock signal
vi) Is USB is a bus?
of the half adder.
vij Draw the block diagram
Giii) Drawa multiplication circuit diagram.
and subroutine?
ix) What's the difference
between interrupt service routine
x) What do you mean by the write-back policy?
xi) What is RISC Pipeline?
xii) What size of MUXs are needed?

2
 GROUP C
5. Answer the question (any one): 6xl
a) Explain the components of the Computer system and what is micro operation?
b) Represent (12.625)0 in 32 bit floating point representation and what is odd parity checker?
c) Describe the Von-Neumann Architecture with diagram? Explain the Bus Structure with examples

6. Answer the question (any onc): 6x1

a) Describe the Flag Register of 8086 microprocessor.

b) Perform multiplication between 23 and 17 using fixed point multiplication algorithm.
c)What are the key characteristics of micro-programmed control?Explain different types of micro
operation.

7. Answer the question (any one):

6xI
a) Discuss the various mapping techniques used in cache memory.
b) What is virtual memory? How does it work?
c) How can you interface RAM and the ROM EPROM to microprocessor 8086? What is the use of
EPROM?