Tutorial 03 Flow Around A Blunt Body

Chapter 8: Flow Around a Blunt Body
This tutorial includes:

8.1.Tutorial Features
8.2. Overview of the Problem to Solve
8.3. Preparing the Working Directory
8.4. Defining the Case Using CFX-Pre
8.5. Obtaining the Solution Using CFX-Solver Manager
8.6. Viewing the Results Using CFD-Post
8.1. Tutorial Features

In this tutorial you will learn about:
• Solving and postprocessing a case where the geometry has been omitted on one side of a symmetry plane.
• Using free-slip wall boundaries as a compromise between accurate flow modeling and computational grid
size.
• Accurately modeling the near-wall flow using Shear Stress Transport (SST) turbulence model.
• Running the CFX-Solver in parallel (optional).
• Creating vector plots in CFD-Post with uniform spacing between the vectors.
• Creating a macro using power syntax in CFD-Post.
Component Feature Details

CFX-Pre User Mode General mode
Analysis Type Steady State
Fluid Type Constant Property Gas
Domain Type Single Domain
Turbulence Model Shear Stress Transport
Boundary Conditions Inlet (Subsonic)
Outlet (Subsonic)
Symmetry Plane
Wall: No-Slip
Wall: Free-Slip
Timestep Physical Time Scale
CFX-Solver Parallel Processing
Manager
CFD-Post Plots Default Locators
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information
of ANSYS, Inc. and its subsidiaries and affiliates. 149
Flow Around a Blunt Body
Component Feature Details

Outline Plot
(Wireframe)
Sampling Plane
Streamline
Vector
Volume
Other Changing the Color
Range
Instancing
Transformation
Lighting Adjustment
Symmetry
Viewing the Mesh
8.2. Overview of the Problem to Solve

In this tutorial, a generic vehicle body is placed into an oncoming side wind of 15 m/s. The turbulence
will be set to Intensity and Length scale with a value of 0.05, which corresponds to 5% turbulence, a
medium level intensity, and with an Eddy Length scale value of 0.1 m.
The goal of this tutorial is to set up, simulate, and then visualize the flow around the body. Since both
the geometry and the flow are symmetric about a vertical plane, you will only use half of the geometry
to find the solution. You will use free-slip wall boundaries on some sides of the domain to model ex-
ternal flow. The flow near the body is modeled using Shear Stress Transport. Since compressibility effects
are not expected to be significant, you can model this as incompressible flow.
Figure 8.1: External Air Flow Over a Generic Vehicle Body
If this is the first tutorial you are working with, it is important to review the following topics before
beginning:
• Running ANSYS CFX Tutorials Using ANSYS Workbench (p. 4)
• Changing the Display Colors (p. 6)
150 of ANSYS, Inc. and its subsidiaries and affiliates.
Defining the Case Using CFX-Pre
8.3. Preparing the Working Directory

1. Create a working directory.
ANSYS CFX uses a working directory as the default location for loading and saving files for a par-
ticular session or project.
2. Ensure the following tutorial input file is in your working directory:
• BluntBodyMesh.gtm
The tutorial input files are available from the ANSYS Customer Portal. To access tutorials and their
input files on the ANSYS Customer Portal, go to http://support.ansys.com/training.
3. Set the working directory and start CFX-Pre.
For details, see Setting the Working Directory and Starting ANSYS CFX in Stand-alone Mode (p. 3).
8.4. Defining the Case Using CFX-Pre

1. In CFX-Pre, select File > New Case.
2. Select General and click OK.
3. Select File > Save Case As.
4. Under File name, type BluntBody.
5. Click Save.
8.4.1. Importing the Mesh

1. Right-click Mesh and select Import Mesh > CFX Mesh.
The Import Mesh dialog box appears.
2. Configure the following setting(s):
Setting Value
File name BluntBodyMesh.gtm
3. Click Open.
8.4.2. Creating the Domain

The flow of air in the domain is expected to be turbulent. The Shear Stress Transport (SST) turbulence
model with automatic wall function treatment will be used because of its highly accurate predictions
of flow separation. To take advantage of the SST model, the boundary layer should be resolved with
at least 10 mesh nodes. In order to reduce computational time, the mesh in this tutorial is much
coarser than that.
As stated in the overview, this tutorial models incompressible flow. Incompressible flow is specified by
choosing an incompressible fluid. You will use Air at 25 C as the incompressible fluid.
As part of the domain settings, you will specify a reference pressure. CFX requires this when modeling
incompressible flow.
1. Click Domain , and set the name to BluntBody.
2. Configure the following setting(s) of BluntBody:
Tab Setting Value

Basic Location and Type
Settings
> Location B1.P3
Fluid and Particle Definitions Fluid 1
Fluid and Particle Definitions
> Fluid 1
> Material Air at 25 C [a]
Domain Models
> Pressure
> Reference Pressure 1 [atm]

Fluid Heat Transfer
Models
> Option None
Turbulence
> Option Shear Stress

Transport
a. Click the Ellipsis icon if the required material does not appear in the
drop-down menu.
3. Click OK.
8.4.3. Creating Composite Regions

An imported mesh may contain many 2D regions. For the purpose of creating boundary conditions, it
can sometimes be useful to group several 2D regions together and apply a single boundary to the
composite 2D region. In this case, you are going to create a Union between two regions that both require
a free-slip wall boundary.
1. From the main menu, select Insert > Regions > Composite Region.
2. Set the name to FreeWalls and click OK.
Tab Setting Value

Basic Dimension (Filter) 2D
Settings
4. Click beside the Region List dialog box, to display the Selection Dialog. Hold down the Ctrl key and
select Free1 and Free2.
5. Click OK to confirm your selection.
6. Click OK to create the composite region.
8.4.4. Creating the Boundaries

The simulation requires inlet, outlet, wall (no slip and free-slip) and symmetry plane boundaries. The
regions for these boundaries were defined when the mesh was created (except for the composite region
just created for the free-slip wall boundary).
8.4.4.1. Inlet Boundary
1. Click Boundary .
2. Under Name, type Inlet.
Tab Setting Value

Basic Boundary Type Inlet
Settings Location Inlet
Boundary Flow Regime
Details
> Option Subsonic
Mass and Momentum
> Option Normal Speed

Mass and Momentum
> Normal Speed 15 [m s^-1]

Turbulence
> Option Intensity and

Length Scale
Turbulence
> Fractional Intensity 0.05 [a]
Turbulence
> Eddy Length Scale 0.1 [m] [a]
a. From the problem description.
4. Click OK.
8.4.4.2. Outlet Boundary

1. Create a new boundary named Outlet.
Tab Setting Value

Basic Boundary Type Outlet
Settings Location Outlet
Boundary Mass and Momentum
Details
> Option Static Pressure
Mass and Momentum
> Relative Pressure 0 [Pa]
3. Click OK.
8.4.4.3. Free-Slip Wall Boundary

The top and side surfaces of the rectangular region will use free-slip wall boundaries.
• On free-slip walls the shear stress is set to zero so that the fluid is not retarded.
• The velocity normal to the wall is also set to zero.
• The velocity parallel to the wall is calculated during the solution.
This boundary is an approximation that may not accurately represent the true flow conditions. By using
a free-slip wall boundary, the flow modeling will be less accurate but the computational grid size can
be reduced by modeling less of the surroundings. If this case were modeling a wind tunnel experiment,
the geometry would match the size and shape of the wind tunnel and use no-slip walls. If this case
were modeling a blunt body open to the atmosphere, a much larger domain would be used to minimize
the effect of the far-field boundary, and the far-field boundary type would be set to either a free-slip
wall or a pressure-specified entrainment opening.
You will apply a single boundary to both walls by using the composite region defined earlier.
1. Create a new boundary named FreeWalls.
Tab Setting Value

Basic Boundary Type Wall
Settings Location FreeWalls
Details
> Option Free Slip Wall
3. Click OK.
8.4.4.4. Symmetry Plane Boundary

1. Create a new boundary named SymP.
Tab Setting Value

Basic Boundary Type Symmetry
Settings Location SymP
3. Click OK.
8.4.4.5. Wall Boundary on the Blunt Body Surface

1. Create a new boundary named Body.
Tab Setting Value

Basic Boundary Type Wall
Settings Location Body
Details
> Option No Slip Wall
3. Click OK.
The remaining 2D regions (in this case, just the low Z face) will be assigned the default boundary which
is an adiabatic, no-slip wall condition. In this case, the name of the default boundary is BluntBody
Default. Although the boundaries Body and BluntBody Default are identical (except for their locations),
the Body boundary was created so that, during postprocessing, its location can be conveniently distin-
guished from the other adiabatic, no-slip wall surfaces.
8.4.5. Setting Initial Values

The initial conditions are consistent with inlet boundaries.
1. Click Global Initialization .
Tab Setting Value

Global Initial Conditions
Settings
> Cartesian Velocity Components
Tab Setting Value

> Option Automatic with
Value
Initial Conditions
>U 15 [m s^-1]
Initial Conditions
>V 0 [m s^-1]
Initial Conditions
>W 0 [m s^-1]
3. Click OK.
8.4.6. Setting Solver Control
1. Click Solver Control .
Tab Setting Value

Basic Convergence Control
Settings
> Max. Iterations 60
Convergence Control
> Fluid Timescale Control
> Timescale Control Physical

Timescale
Convergence Control
> Fluid Timescale Control
> Physical Timescale 2 [s][ a ]

Convergence Criteria
> Residual Target 1e-05

a. Based on the air speed and the size of the object.
3. Click OK.
Obtaining the Solution Using CFX-Solver Manager
8.4.7. Writing the CFX-Solver Input (.def) File
1. Click Define Run .
Setting Value
File name BluntBody.def
3. Click Save.
CFX-Solver Manager automatically starts and, on the Define Run dialog box, Solver Input File is
set.
4. If using stand-alone mode, quit CFX-Pre, saving the simulation (.cfx) file at your discretion.
8.5. Obtaining the Solution Using CFX-Solver Manager

This tutorial introduces the parallel solver capabilities of CFX.
Note
The results produced will be identical, whether produced by a parallel or serial run.
If you do not want to solve this tutorial in parallel (on more than one processor) or you do not have a
license to run the CFX-Solver in parallel, proceed to Obtaining a Solution in Serial (p. 157).
If you do not know if you have a license to run the CFX-Solver in parallel, you should either ask your
system administrator, or query the license server (see the ANSYS, Inc. Licensing Guide (which is installed
with the ANSYS License Manager) for details). Alternatively proceed to Obtaining a Solution in Seri-
al (p. 157).
If you would like to solve this tutorial in parallel on the same machine, proceed to Obtaining a Solution
with Local Parallel (p. 158).
If you would like to solve this tutorial in parallel across different machines, proceed to Obtaining a
Solution with Distributed Parallel (p. 159).
8.5.1. Obtaining a Solution in Serial

When CFX-Solver Manager has started, you can obtain a solution to the CFD problem by using the fol-
lowing procedure.
1. Click Start Run.
2. When CFX-Solver is finished, select the check box next to Post-Process Results.
3. If using stand-alone mode, select the check box next to Shut down CFX-Solver Manager.
4. Click OK. Continue this tutorial from Viewing the Results Using CFD-Post (p. 162).
8.5.2. Obtaining a Solution in Parallel

8.5.2.1. Background to Parallel Running in CFX
Using the parallel capability of the CFX-Solver enables you to divide a large CFD problem so that it can
run on more than one processor/machine at once. This saves time and, when multiple machines are
used, avoids problems that arise when a CFD calculation requires more memory than a single machine
has available. The partition (division) of the CFD problem is automatic.
A number of events occur when you set up a parallel run and then ask the CFX-Solver to calculate the
solution:
• Your mesh will be divided into the number of partitions that you have chosen.
• The CFX-Solver runs separately on each of the partitions on the selected machine(s).
• The results that one CFX-Solver process calculates affects the other CFX-Solver processes at the interface
between the different sections of the mesh.
• All of the CFX-Solver processes are required to communicate with each other and this is handled by the
master process.
• The master process always runs on the machine that you are logged into when the parallel run starts. The
other CFX-Solver processes are slave processes and may be run on other machines.
• After the problem has been solved, a single results file is written. It will be identical to a results file from the
same problem run as a serial process, with one exception: an extra variable Real partition number
will be available for the parallel run. This variable will be used later in this tutorial during post processing.
8.5.2.2. Obtaining a Solution with Local Parallel

In CFX-Solver Manager, the Define Run dialog box should already be open.
To run in local parallel mode:
1. Leave Type of Run set to Full.
If Type of Run was instead set to Partitioner Only, your mesh would be split into a number
of partitions but would not be run in the CFX-Solver afterwards.
2. Set Run Mode to a parallel mode suitable for your configuration; for example, IBM MPI Local Par
allel.
This is the recommended method for most applications.
3. If required, click Add Partition to add more partitions.
Ideally, the number of partitions should not exceed the number of available processor cores.
4. Select Show Advanced Controls.
5. Click the Partitioner tab at the top of the dialog box.
6. Use the default MeTiS partitioner.
Your model will be divided into a number of sections, with each section running in its own CFX-
Solver process. The default is the MeTiS partitioner because it produces more efficient partitions
than either Recursive Coordinate Bisection or User Specified Direction.
7. Click Start Run.
10. Click OK.
Continue this tutorial from Text Output when Running in Parallel (p. 160).
8.5.2.3. Obtaining a Solution with Distributed Parallel

Before running in Distributed Parallel mode, ensure that your system has been configured as described
in the installation documentation.
In CFX-Solver Manager, the Define Run dialog box should already be open.
1. Leave Type of Run set to Full.
If Type of Run was instead set to Partitioner Only, your mesh would be split into a number
of partitions but would not be run in the CFX-Solver afterwards.
2. Set Run Mode to a parallel mode suitable for your environment; for example, IBM MPI Distributed
Parallel.
The name of the machine that you are currently logged into should be in the Host Name list. You
are going to run with two partitions on two different machines, so another machine must be added.
3. Click Insert Host to specify a new host machine.
• The Select Parallel Hosts dialog box is displayed. This is where you choose additional machines to run
your processes.
• Your system administrator should have set up a hosts file containing a list of the machines that are
available to run the parallel CFX-Solver.
• The Host Name column displays names of available hosts.
• The second column shows the number of processors on that machine.
• The third shows the relative processor speed: a processor on a machine with a relative speed of 1 would
typically be twice as fast as a machine with a relative speed of 0.5.
• The last column displays operating system information.
• This information is read from the hosts file; if any information is missing or incorrect your system ad-
ministrator should correct the hosts file.
Note
The # processors, relative speed and system information does not have to be specified
to be able to run on a host.
4. Select the name of another machine in the Host Name list.
Select a machine that you can log into.
5. Click Add.
The name of the machine is added to the Host Name column.
Note
Ensure that the machine that you are currently logged into is in the Hosts Name list in
the Define Run dialog box.
6. Close the Select Parallel Hosts dialog box.
7. Select Show Advanced Controls.
8. Click the Partitioner tab at the top of the dialog box.
9. Use the default MeTiS partitioner.
Your model will be divided into two sections, with each section running in its own CFX-Solver
process. The default is the MeTiS partitioner because it produces more efficient partitions than
either Recursive Coordinate Bisection or User Specified Direction.
10. Click Start Run to begin the parallel run.
11. Click OK on the dialog box.
14. Click OK.
8.5.2.4. Text Output when Running in Parallel

The text output area shows what is being written to the output file. You will see information similar to
the following:
+--------------------------------------------------------------------+
| Job Information at Start of Run |
+--------------------------------------------------------------------+
Run mode: partitioning run
+------------------------------+------+--------+----------+----------+
| Host | Mesh | PID | Job Started |
| | Part | | DD/MM/YY | hh:mm:ss |
+------------------------------+------+--------+----------+----------+
| fastmachine1 | 1 | 5952 | 19/02/13 | 10:50:09 |
+------------------------------+------+--------+----------+----------+
This tells you that the information following is concerned with the partitioning. After the partitioning
job has finished, you will find:
+--------------------------------------------------------------------+
| Partitioning Information |
+--------------------------------------------------------------------+
Partitioning information for domain: BluntBody
+------------------+------------------------+-----------------+
| Elements | Vertices | Faces |
+------+------------------+------------------------+-----------------+
| Part | Number % | Number % %Ovlp | Number % |
+------+------------------+------------------------+-----------------+
| Full | 131878 | 37048 | 11318 |
+------+------------------+------------------------+-----------------+
| 1 | 67873 50.4 | 19431 50.4 4.0 | 5705 49.5 |
| 2 | 66865 49.6 | 19151 49.6 4.0 | 5820 50.5 |
+------+------------------+------------------------+-----------------+
| Sum | 134738 100.0 | 38582 100.0 4.0 | 11525 100.0 |
+------+------------------+------------------------+-----------------+
+--------------------------------------------------------------------+
| Partitioning CPU-Time Requirements |
+--------------------------------------------------------------------+
- Preparations 3.689E-01 seconds

- Low-level mesh partitioning 5.599E-02 seconds
- Global partitioning information 9.998E-03 seconds
- Element and face partitioning information 7.999E-03 seconds
- Vertex partitioning information 0.000E+00 seconds
- Partitioning information compression 0.000E+00 seconds
- Summed CPU-time for mesh partitioning 4.609E-01 seconds
+--------------------------------------------------------------------+
| Job Information at End of Run |
+--------------------------------------------------------------------+
+---------------------------+------+----------+----------+-----------+
| Host | Mesh | Job Finished | CPU |
| | Part | DD/MM/YY | hh:mm:ss | seconds |
+---------------------------+------+----------+----------+-----------+
| fastmachine1 | 1 | 19/02/13 | 10:50:09 | 8.020E-01 |
+---------------------------+------+----------+----------+-----------+
Total wall clock time: 7.990E-01 seconds

or: ( 0: 0: 0: 0.799 )
( Days: Hours: Minutes: Seconds )
This marks the end of the partitioning job. The CFX-Solver now begins to solve your parallel run:
+--------------------------------------------------------------------+
| Job Information at Start of Run |
+--------------------------------------------------------------------+
Run mode: parallel run (IBM MPI)
+------------------------------+------+--------+----------+----------+
| Host | Mesh | PID | Job Started |
| | Part | | DD/MM/YY | hh:mm:ss |
+------------------------------+------+--------+----------+----------+
| fastmchine1 | 1 | 6044 | 19/02/13 | 10:50:11 |

| | 2 | 3276 | 19/02/13 | 10:50:11 |
+------------------------------+------+--------+----------+----------+
The machine that you are logged into runs the master process, and controls the overall simulation. The
second machine selected will run the slave process. If you had more than two processes, each additional
process is run as a slave process.
The master process in this example is running on the mesh partition number 1 and the slave is running
on partition number 2. You can find out which nodes and elements are in each partition by using CFD-
Post later on in the tutorial.
When the CFX-Solver finishes, the output file displays the job information and a dialog box to indicate
completion of the run.
8.6. Viewing the Results Using CFD-Post

In CFD-Post, you will:
• Create an instance transform object to recreate the full geometry
• Create a vector plot that shows how the flow behaves around the body
• Create a pressure plot that shows the pressure distribution on the body
• Make a surface streamline that shows the path of air along the surface of the body
• Examine the values of the dimensionless wall distance to make sure that the mesh is sufficiently fine near
the walls
8.6.1. Using Symmetry Plane to Display the Full Geometry

Earlier in this tutorial you used a symmetry plane boundary because the entire blunt body is symmet-
rical about a plane. Due to this symmetry, it was necessary to use only half of the full geometry to cal-
culate the CFD results. However, for visualization purposes, it is helpful to use the full blunt body. CFD-
Post is able to recreate the full data set from the half that was originally calculated. This is done by
creating an Instance Transform object.
8.6.1.1. Manipulating the Geometry

You need to manipulate the geometry so that you will be able to see what happens when you use the
symmetry plane. The CFD-Post features that you have used in earlier tutorials will not be described in
detail. New features will be described in detail.
• Right-click a blank area in the viewer and select Predefined Camera > View From +X.
8.6.1.2. Creating an Instance Transform

Instance Transforms are used to visualize a full geometry representation in cases where the simulation
took advantage of symmetry to solve for only part of the geometry. There are three types of transforms
that you can use: Rotation, Translation, Reflection/Mirroring. In this tutorial, you will create a Reflection
transform located on a plane.
1. Click Location > Plane and set the name to Reflection Plane.
Viewing the Results Using CFD-Post
Tab Setting Value

Geometry Definition
> Method ZX Plane

Definition
>Y 0.0 [m]

Render Show Faces (cleared)
3. Click Apply.
This creates a plane at y=0, the same location as the symmetry plane defined in CFX-Pre. Now the
instance transform can be created using this plane:
4. From the main menu, select Insert > Instance Transform and accept the default name.
Tab Setting Value

Definition Instancing Info From Do- (Cleared)
main
Apply Rotation (Cleared)
Apply Reflection (Selected)
Apply Reflection
> Plane Reflection Plane
6. Click Apply.
8.6.1.3. Using the Reflection Transform

You can apply the new transform to graphics objects. For example, you can modify the display of the
wireframe as follows:
1. Under the Outline tab, in User Locations and Plots, configure the following setting(s) of
Wireframe:
Tab Setting Value

View Apply Instancing Transform
> Transform Instance Transform

1
2. Click Apply.
3. Zoom so that the geometry fills the Viewer.
You will see the full blunt body.
In this case, you created a new instance transform and applied it to the wireframe. This caused only
the wireframe object to be mirrored. If you had modified the default transform instead of creating a
new one, then all graphics (including those not yet made) would be mirrored by default.
8.6.2. Creating Velocity Vectors

You are now going to create a vector plot to show velocity vectors behind the blunt body. You need
to first create an object to act as a locator, which, in this case, will be a sampling plane. Then, create
the vector plot itself.
8.6.2.1. Creating the Sampling Plane

A sampling plane is a plane with evenly spaced sampling points on it.
1. Right-click a blank area in the viewer and select Predefined Camera > View From +Y.
This ensures that the changes can be seen.
2. Create a new plane named Sample.
3. Configure the following setting(s) to create a sampling plane that is parallel to the ZX plane and located
at x= 6 m, y= 0.001 m and z= 1 m relative to blunt object:
Tab Setting Value

Geometry Definition
> Method Point and Normal

Definition
> Point 6, -0.001, 1

Definition
> Normal 0, 1, 0
Plane Bounds
> Type Rectangular

Plane Bounds
> X Size 2.5 [m]

Plane Bounds
> Y Size 2.5 [m]

Plane Type Sample
Plane Type
> X Samples 20
Plane Type
> Y Samples 20
Tab Setting Value

Render Show Faces (Cleared)
Show Mesh Lines (Selected)
4. Click Apply.
You can zoom in on the sampling plane to see the location of the sampling points (where lines
intersect). There are a total of 400 (20 * 20) sampling points on the plane. A vector can be created
at each sampling point.
5. Turn off the visibility of Sample.
8.6.2.2. Creating a Vector Plot Using Different Sampling Methods
1. Click Vector and accept the default name.
Tab Setting Value

Geometry Definition
> Locations Sample

Definition
> Sampling Vertex

Symbol Symbol Size 0.25
3. Click Apply.
4. Zoom until the vector plot is roughly the same size as the viewer.
You should be able to see a region of recirculation behind the blunt body.
5. Ignore the vertices on the sampling plane and increase the density of the vectors by applying the following
settings:
Tab Setting Value

Geometry Definition
> Sampling Equally Spaced

Definition
> # of Points 1000
6. Click Apply.
7. Change the location of the Vector plot by applying the following setting:
Tab Setting Value

Geometry Definition
> Locations SymP
8. Click Apply.
8.6.3. Displaying Pressure Distribution on Body and Symmetry Plane

1. Configure the following setting(s) of the boundary named Body:
Tab Setting Value

Color Mode Variable
Variable Pressure

1
2. Click Apply.
3. Configure the following setting(s) of SymP:
Tab Setting Value

Render Show Faces (Cleared)
Show Mesh Lines (Selected)
4. Click Apply.
You will be able to see the mesh around the blunt body, with the mesh length scale decreasing
near the body, but still coarse in the region of recirculation. By zooming in, you will be able to see
the layers of inflated elements near the body.
8.6.4. Creating Surface Streamlines to Display the Path of Air along the Surface
of the Body
In order to show the path of air along the surface of the blunt body, surface streamlines can be made
as follows:
1. Turn off the visibility of Body, SymP and Vector 1.
2. Create a new plane named Starter.
Tab Setting Value

Geometry Definition
Tab Setting Value

> Method YZ Plane
X -0.1 [m]
4. Click Apply.
5. Right-click a blank area in the viewer and select Predefined Camera > Isometric View (Z up).
The plane appears just upstream of the blunt body.
6. Turn off the visibility of the plane.
This hides the plane from view, although the plane still exists.
7. Click Streamline and click OK to accept the default name.
Tab Setting Value

Geometry Type Surface Streamline
Definition
> Surfaces Body

Definition
> Start From Locations

Definition
> Locations Starter

Definition
> Max Points 100

Definition
> Direction Forward
9. Click Apply.
The surface streamlines appear on half of the surface of the blunt body. They start near the upstream
end because the starting points were formed by projecting nodes from the plane to the blunt body.
8.6.5. Moving Objects

In CFD-Post, you can reposition some locator objects directly in the viewer by using the mouse.
1. Turn on the visibility of the plane named Starter.
2. Select the Single Select mouse pointer from the Selection Tools toolbar.
3. In the viewer, click the Starter plane to select it, then drag it along the X axis.
Notice that the streamlines are redrawn as the plane moves. The rate at which the streamlines are
redrawn is dependent on your computer's speed. If the streamlines are updated infrequently, you
may find it useful to move the mouse very slowly.
8.6.6. Creating a Surface Plot of y+

The velocity next to a no-slip wall boundary changes rapidly from a value of zero at the wall to the free
stream value a short distance away from the wall. This layer of high velocity gradient is known as the
boundary layer. Many meshes are not fine enough near a wall to accurately resolve the velocity profile
in the boundary layer. Wall functions can be used in these cases to apply an assumed functional shape
of the velocity profile. Other grids are fine enough that they do not require wall functions, and application
of the latter has little effect. The majority of cases fall somewhere in between these two extremes, where
the boundary layer is partially resolved by nodes near the wall and wall functions are used to supplement
accuracy where the nodes are not sufficiently clustered near the wall.
One indicator of the closeness of the first node to the wall is the dimensionless wall distance . It is
good practice to examine the values of at the end of your simulation. At the lower limit, a value of
less than or equal to 11 indicates that the first node is within the laminar sublayer of the boundary
flow. Values larger than this indicate that an assumed logarithmic shape of the velocity profile is being
used to model the boundary layer portion between the wall and the first node. Ideally you should
confirm that there are several nodes (3 or more) resolving the boundary layer profile. If this is not ob-
served, it is highly recommended that more nodes be added near the wall surfaces in order to improve
simulation accuracy. In this tutorial, a coarse mesh is used to reduce the run time. Thus, the grid is far
too coarse to resolve any of the boundary layer profile, and the solution is not highly accurate.
A surface plot is one which colors a surface according to the values of a variable: in this case, .A
surface plot of can be obtained as follows:
1. Turn off the visibility of all previous plots.
2. Under the Outline tab, configure the following settings of BluntBodyDefault:
Tab Setting Value

Color Mode Variable
Variable Yplus [a]

1
a. Click the Ellipsis icon to the right of the Variable dropdown menu to view
a full list of variables, including Yplus.
3. Click Apply.
4. Under the Outline tab, configure the following settings of Body:
Tab Setting Value

Color Mode Variable
Variable Yplus

1
5. Click Apply.
8.6.7. Viewing the Mesh Partitions (Parallel Only)

If you solved this tutorial in parallel, then an additional variable named Real partition number
will be available in CFD-Post
1. Create an isosurface of Real partition number equal to 1.
2. Create a second isosurface of Real partition number equal to 1.999.
The two isosurfaces show the edges of the two partitions. The gap between the two plots shows the
overlap nodes. These were contained in both partitions 1 and 2.
When you have finished looking at the results, quit CFD-Post.

Tutorial 03 Flow Around A Blunt Body

Uploaded by

Copyright:

Available Formats

Tutorial 03 Flow Around A Blunt Body

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tutorial 03 Flow Around A Blunt Body

Uploaded by

Copyright:

Available Formats

Chapter 8: Flow Around a Blunt Body

This tutorial includes:

8.1. Tutorial Features

• Running the CFX-Solver in parallel (optional).

• Creating a macro using power syntax in CFD-Post.

Component Feature Details

Component Feature Details

8.2. Overview of the Problem to Solve

Figure 8.1: External Air Flow Over a Generic Vehicle Body

• Running ANSYS CFX Tutorials Using ANSYS Workbench (p. 4)

• Changing the Display Colors (p. 6)

8.3. Preparing the Working Directory

2. Ensure the following tutorial input file is in your working directory:

3. Set the working directory and start CFX-Pre.

8.4. Defining the Case Using CFX-Pre

2. Select General and click OK.

3. Select File > Save Case As.

4. Under File name, type BluntBody.

8.4.1. Importing the Mesh

The Import Mesh dialog box appears.

2. Configure the following setting(s):

8.4.2. Creating the Domain

1. Click Domain , and set the name to BluntBody.

2. Configure the following setting(s) of BluntBody:

Tab Setting Value

> Material Air at 25 C [a]

> Reference Pressure 1 [atm]

> Option Shear Stress

8.4.3. Creating Composite Regions

2. Set the name to FreeWalls and click OK.

3. Configure the following setting(s):

Tab Setting Value

5. Click OK to confirm your selection.

6. Click OK to create the composite region.

8.4.4. Creating the Boundaries

8.4.4.1. Inlet Boundary

2. Under Name, type Inlet.

3. Configure the following setting(s):

Tab Setting Value

> Option Normal Speed

> Normal Speed 15 [m s^-1]

> Option Intensity and

> Fractional Intensity 0.05 [a]

> Eddy Length Scale 0.1 [m] [a]

a. From the problem description.

8.4.4.2. Outlet Boundary

2. Configure the following setting(s):

Tab Setting Value

> Relative Pressure 0 [Pa]

8.4.4.3. Free-Slip Wall Boundary

• The velocity normal to the wall is also set to zero.

• The velocity parallel to the wall is calculated during the solution.

1. Create a new boundary named FreeWalls.

2. Configure the following setting(s):

Tab Setting Value

8.4.4.4. Symmetry Plane Boundary

2. Configure the following setting(s):

Tab Setting Value

8.4.4.5. Wall Boundary on the Blunt Body Surface