HS-AC1

SERVICE MANUAL US Model

Ver. 1.0 2009.02

SPECIFICATIONS
Power requirements: AC 120 V, 60 Hz
Power output: DC 19.5 V, 4.5 A (TOTAL)
Each output of DC CABLES and DC OUT
connector terminal: 2.5 A (LPS)
DC 10 V (LPS), 0.25 A
Power consumption: 120 V, 1.5 A
Operating temperature: 0 °C - 30 °C (32 °F - 86 °F)
Storage temperature: – 20 °C - 60 °C (– 4 °F - 140 °F)
Dimensions: 190 × 65 × 250 mm (7 1/2 × 2 5/8 × 10 inches)
(w/h/d)
Mass: 3.8 kg (8 lbs 5 oz)
Supplied accessory: AC power cord (mains lead)

Design and specifications are subject to change without notice.

POWER SUPPLY
9-889-384-01 Sony Corporation
2009B04-1 Audio&Video Business Group
© 2009.02 Published by Sony Techno Create Corporation
HS-AC1

SAFETY CHECK-OUT NOTES ON CHIP COMPONENT REPLACEMENT

After correcting the original service problem, perform the follow- • Never reuse a disconnected chip component.
ing safety check before releasing the set to the customer: • Notice that the minus side of a tantalum capacitor may be dam-
Check the antenna terminals, metal trim, “metallized” knobs, aged by heat.
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below. UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
LEAKAGE TEST free mark (LF) indicating the solder contains no lead.
The AC leakage from any exposed metal part to earth ground and (Caution: Some printed circuit boards may not come printed with
from all exposed metal parts to any exposed metal part having a the lead free mark due to their particular size)
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods. : LEAD FREE MARK
1. A commercial leakage tester, such as the Simpson 229 or RCA Unleaded solder has the following characteristics.
WT-540A. Follow the manufacturers’ instructions to use these • Unleaded solder melts at a temperature about 40 °C higher
instruments. than ordinary solder.
2. A battery-operated AC milliammeter. The Data Precision 245 Ordinary soldering irons can be used but the iron tip has to be
digital multimeter is suitable for this job. applied to the solder joint for a slightly longer time.
3. Measuring the voltage drop across a resistor by means of a Soldering irons using a temperature regulator should be set to
VOM or battery-operated AC voltmeter. The “limit” indication about 350 °C.
is 0.75 V, so analog meters must have an accurate low-voltage Caution: The printed pattern (copper foil) may peel away if
scale. The Simpson 250 and Sanwa SH-63Trd are examples the heated tip is applied for too long, so be careful!
of a passive VOM that is suitable. Nearly all battery operated • Strong viscosity
digital multimeters that have a 2 V AC range are suitable. (See Unleaded solder is more viscous (sticky, less prone to flow)
Fig. A) than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
To Exposed Metal • Usable with ordinary solder
Parts on Set
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

AC
0.15 μF 1.5 kΩ voltmeter
(0.75 V) TABLE OF CONTENTS

1. GENERAL ................................................................... 3

2. DISASSEMBLY
Earth Ground 2-1. D.C Fan ........................................................................... 4
Fig. A. Using an AC voltmeter to check AC leakage. 2-2. Power Transformer ......................................................... 5
2-3. SENSOR Board, AC Board ............................................ 5

3. DIAGRAMS
3-1. Printed Wiring Boards .................................................... 7
3-2. Schematic Diagram ......................................................... 8

4. EXPLODED VIEWS
4-1. Chassis Section ............................................................... 9
4-2. AC Board Section ........................................................... 10

5. ELECTRICAL PARTS LIST .............................. 11

SAFETY-RELATED COMPONET WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

2
 HS-AC1
SECTION 1
This section is extracted
GENERAL from instruction manual.

Part names and descriptions Connecting power supply cords

You can connect up to two Keypads directly to a Power Supply in
order to improve sound coverage of the Keypad. For details on Keypad
connection, refer to the Keypad (HS-KP1) installer’s manual.
You can use any commercially available cord of gauge AWG 18 to AWG
DC OUT 26. AWG 18 cords are recommended as signal loss is less.

2.5A(LPS)

2.5A(LPS)
19.5V 19.5V 19.5V 19.5V DC10V

19.5V

19.5V
GND

GND
2.5A(LPS) 2.5A(LPS) 2.5A(LPS) 2.5A(LPS) 0.25A(LPS)

DC 19.5V = TOTAL4.5A
DC CABLES x4
CONNECTOR TERMINALS x2
 Tip
For a Keypad (HS-KP1) powered via the Distribution Panel (HS-MB1)
connected to HS-AC1, sound coverage will improve if the Keypad is
directly connected to HS-AC1 in addition to the Distribution Panel (HS-
 DC 10 V and DC 19.5 V cables
MB1).
To Distribution Panel (HS-MB1)
Connect the DC 10 V cable and DC 19.5 V cables to their respective 1 Strip 10 mm (0.4 inch) of insulation off the cords and twist the bare
jacks on the side of Distribution Panel (HS-MB1): DC IN 10 V and DC wires together tightly.
IN 19.5 V. Note
For details, refer to the Distribution Panel (HS-MB1) installer’s manual. Do not use a cord that is kinked, tarnished or otherwise damaged.

To AV Wall Port (HS- WV1) 2 Insert the cords into the plug-in terminal block (supplied) as far as
Connect the DC 19.5 V cables to the DC IN 19.5 V jacks on the panel they will go. Use a flathead screwdriver to tighten each of the four
of AV Wall Port (HS-WV1). screws. Then, insert the terminal block into DC OUT (for the
For details, refer to the AV Wall Port (HS-WV1) installer’s manual. Keypad).

 DC OUT
Connect to the rear of Keypad (HS-KP1) using cords suitable for DC O
UT
supplying power. 19.5V
2.5A(L
PS) 19.5V
2.5A(L

2.5A(LPS)
DC 19 PS)

2.5A(LPS)
19.5V
GND
.5V =

19.5V
TOTAL4

GND
DC CA 19.5V
BL .5A
CONN ES x4 2.5A(L 19.5V
ECTO PS)
2.5A(L
R TERM DC10
0.25A(LV
INALS PS)
x2
PS)

Screw

Combinations

This unit Keypad

DC OUT DC IN
A, C GND GND
B, D 19.5 V 19.5 V
Note
● Be sure to connect the terminals correctly as shown in the table
above; GND to GND, and DC OUT 19.5 V to DC IN 19.5 V.
● Make sure none of the bare wires touch each other. If they do, it
may cause a short-circuit, which could damage the system.

3
HS-AC1
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.

SET

2-1. D.C FAN

(Page 4)

2-2. POWER TRANSFORMER

(Page 5)

2-3. SENSOR BOARD,

AC BOARD
(Page 5)

Note: Follow the disassembly procedure in the numerical order shown below.
2-1. D.C FAN

 two screws
(flat head (TP))  two screws
(flat head (TP))
 two screws
(flat head (TP))
 case (ADP)

RE bracket (M) RB screw

 two screws
(+BVTT 4 × 8)
(flat head (TP))
 two screws
 (+BVTP 3 × 8)

 screw
(+BVTT 4 × 8)
 two screws
(+BVTP 3 × 8)

RT D.C fan

 CN906 (2P)

4
 HS-AC1

2-2. POWER TRANSFORMER

 power transformer

 CN902 (2P)
 CN901 (2P)

 CN903 (3P)

 two screws
(case 4 × 8)

 two screws
(case 4 × 8)

2-3. SENSOR BOARD, AC BOARD

 CN905 (2P)
RI CN907 (5P) RL bracket (HS-IC)
RK screw
(+BVTP 3 × 8)
 CN900 (2P)

RM SENSOR board

RG three screws
(+BVTP 3 × 8)
 CN910 (2P)
 CN904 (2P) X AC board
 CN909 (2P)
 CN908 (2P)

RH  two cords

 lock plate
RB lock plate

 lock plate RT cord

 two cords
RE screw
(+BVTP 3 × 8)

5
HS-AC1
SECTION 3
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards: For Schematic Diagrams:
Note: Note:
• X : Parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF) 50
• : Pattern from the side which enables seeing. WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• 2 : nonflammable resistor.
• C : panel designation.

Note: The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

• A : B+ Line.
• Voltages is dc with respect to ground under no-signal
(detuned) conditions.
no mark : POWER ON
• Voltages are taken with VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.

6
 HS-AC1

3-1. PRINTED WIRING BOARDS • : Uses unleaded solder.

1 2 3 4 5 6 7 8

DC OUT

A J908 J909 J904 J910 J905

19.5V 2.5A(LPS) 19.5V 2.5A(LPS) 19.5V 2.5A(LPS) 19.5V 2.5A(LPS) DC 10V 0.25A(LPS)
    
TB900
DC 19.5V TOTAL4.5A

( DC CABLES x4
CONNECTOR TERMINALS x2 ) BLK
CN905
WHT

WHT

WHT

WHT
BLK

BLK

BLK

BLK
3

2.5A(LPS)

2.5A(LPS)
B SENSOR

19.5V

19.5V
GND

GND
1 2 1 2 1 2 1 2 RED
1
CN908 CN909

(CHASSIS)
CN904 CN910
BOARD
1 TB900 4 A900
CN908 CN909 JL911

R993
R994
ET903 1 2 1 2
JL909 A901 ET901
JL910 JL913 JL912
JL914 CN904
PS901

PS902
1 2

JL915
JL927 JL928 PS906
PS903

R996
R997
PS904 CN910
C

IC991
D900
1 2
PS905 JL996
JL926 JL929
TH900

1
R911
JL997

2
ECB

Q901
Q902

3
D911

R910

ECB
D991 JL998
JW903

R991

R995
R998
D992
C905

C904

R918
C906

A902 R901

JL991
R914 JL994 JL993JL992

JL995
Q903 R902
R919 6 1 CN997 11
ECB
D D906
R917 R916
(16)

AC BOARD
R915

ECB
D910

Q904

D912
1-878-184-

GRY
GRY
GRY
GRY

BLU
R913
C901

R921
D909

C911 C912
JL917 CN905

5
JW906

IC901
8 JL923
3

R920
JW904
JW905

1
E
1

JL924 CN906
JL920
CN906 1 2
1 2
JL918 JL925

R907
R912
JL919

+ RED
– BLK
JL916 JL921
A903

GRY
GRY
GRY
GRY

BLU
C902 JL922

6 1 6 1
CN907 CN907

F
D904

D903

D902

D901

FAN901
DC FAN
F901

F902
BLU

BLU

T901
F904

F903

POWER 3 1
TRANSFORMER CN903 RY901

G
JL908
JL906

JL907 JL904 JL905

RED
BLU

3 1 1 3
1 3 CN903
CN902 • Semiconductor Location
CN902

Ref. No. Location Ref. No. Location Ref. No. Location

JL902

CN901 CN901
1 3
D900 C-5 D909 D-6 IC901 E-6
1 3
H D901 F-5 D910 D-6 IC991 C-8
WHT

ORG

JL903
D902 F-5 D911 C-6
F900

JL901 D903 F-5 D912 D-6 Q901 C-6

JL900

D908

3 CN900 1
D904 F-5 D991 C-7 Q902 C-6
15 D906 D-5 D992 D-7 Q903 D-6
1-877-979- (16) D908 H-6 Q904 D-5
BRN
BLU

GRN/YEL
I (CHASSIS)

J901
~ AC IN

HS-AC1
7 7
HS-AC1

3-2. SCHEMATIC DIAGRAM

1 2 3 4 5 6 7 8 9 10

PS904
AC BOARD 3.15A
125V
JL927
CN908
2P J908
1 +19.5V
A 2 GND
19.5V 2.5A(LPS)

PS906
3.15A CN910
125V 2P
JL929 J910
D900 1 +19.5V
F901 D20XBS6 19.5V 2.5A(LPS)
T10AL 250V 2 GND
RECT
PS903
CN902 3.15A CN904
~ TH900 125V 2P
2P JW903 JL926 J904
JL904 1 +19.5V
1 JL915 19.5V 2.5A(LPS) DC OUT
JL905 ~ 2 GND
3
B F902
T10AL 250V
D906
D20XBS6
C904 C905 C906
PS905
3.15A CN909
RECT R918 125V 2P
6800 6800 6800 10k JL928 J909
35V 35V 35V 1 +19.5V
RY901 ~ 19.5V 2.5A(LPS)
E
2 GND
R916
120
ET901 ~ PS901 TB900
3.15A 4P
D908 125V JL911
1 GND GND TB900
1SS133T-72 JL914
R919 2 +19.5V 19.5V 2.5A(LPS)
120 DC 19.5V TOTAL4.5A
0.6 JL910 JL913

C
0.8
0.8 R911 D912
1SS133T-72
IC901
IC901
E
JL912
3
4
GND
+19.5V
GND
19.5V 2.5A(LPS) ( DC CABLES x4
CONNECTOR TERMINALS x2 )
0.3 1k PS902
NJM2904D 3.15A
R901 R902 TEMPERATURE CONTROL ET903 125V
R910 D911 JL909
SENSOR BOARD
47k 10k 330 1SS133T-72 1.3 9.6
VCC

8
Q904
Q901 1.4 1.3
2SA1038S-RSE-TP CN906

7
2SC2603TP-EF R920 C912 R997
RELAY DRIVER Q902 FAN ON/OFF 2P 91k R998
1M 0.9 1.2 0.1 JL920 +

1SS133T-72
2SC2229-OY 2 FAN(+) 10k

6
ABNORMAL TEMP DETECT FAN901

D910
C911 R921 9.6 0 JL919 –
0.1 0.9 1M 1 FAN(-) DC FAN
VSS R996

5
R907
R912 9.5 100k
1k

TEMPERATURE SENSOR
R913
1k 10k
D

LM61CIZ/LFT2
1SS133T-72
R915

IC991
4.7k
IC991

D909

VOUT

GND
R917 9.4

+Vs
1k 0.3
1 2 3
R914

6.1

0.9
330

Q903 CN907

JL996

JL998
CN997
2SC2229-OY 5P 6P
FAN START DETECT

JL997
JL921 JL991
1 Compare_FAN START Compare_FAN START 1
JL922 JL992
3 VOUT VOUT 3
E JL923
4 Compare_Over_temp Compare_Over_temp 4
JL993
JL924 JL994 R994
5 Virtual_GND Virtual_GND 5
JL925 JL995 82k
6 Virtual_+10V Virtual_+10V 6
R995
C901 D992 R993 10k
CN903 0.1 1SS133T-72 68k
F903
3P T5AL 250V
JL906
1
JL907 R991
2 1k D991
JL908 MTZJ-T-72-6.2B
3 D903
F904 10EDB40-TB5 CN905
F T5AL 250V RECT
JL918
3P

1 +10V J905
T901 D901 C902 JL917
POWER 3300 2 NC DC OUT
10EDB40-TB5
CN901 F900 RECT 25V JL916
TRANSFORMER 2P 3 GND
JL902 T2.5AL 250V DC10V 0.25A(LPS)
1
JL903 D904
3 10EDB40-TB5
RECT

CN900 D902
2P 10EDB40-TB5
JL901 RECT
1
JL900
G E 3

(CHASSIS)
J901
 AC IN

HS-AC1
8 8
 HS-AC1
SECTION 4
EXPLODED VIEWS
Note: The components identified by mark 0
• -XX and -X mean standardized parts, so • Color Indication of Appearance Parts or dotted line with mark 0 are critical for
they may have some difference from the Example: safety.
original one. KNOB, BALANCE (WHITE) . . . (RED) Replace only with part number specified.
• Items marked “*” are not stocked since ↑ ↑
they are seldom required for routine ser- Parts Color Cabinet’s Color
vice. Some delay should be anticipated • Accessories are given in the last of this
when ordering these items. parts list.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.

4-1. CHASSIS SECTION

#2
1
#1
not supplied
1 1 #1
#2

FAN901

AC board section
#1

not supplied

not supplied
not supplied
(J901)
2
T901 #2

4
4

J905

4
3
#1
J909
not supplied J904 J910
3 5
J908

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-227-843-31 SCREW (TP), FLAT HEAD 0 J908 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
2 2-580-644-01 SCREW, +KTP2 3X8 (DC OUT 19.5V 2.5A(LPS))
3 3-279-496-01 SCREW (CASE 4X8) 0 J909 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
4 4-111-200-01 PLATE, LOCK (DC OUT 19.5V 2.5A(LPS))
5 1-817-961-11 CONNECTOR 4P (DC OUT DC 19.5V TOTAL4.5V) 0 J910 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT 19.5V 2.5A(LPS))
FAN901 1-787-331-11 FAN, D.C. 0 T901 1-445-509-11 TRANSFORMER, POWER
J901 (Not supplied) INLET, AC (2P) (~ AC IN) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
0 J904 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT 19.5V 2.5A(LPS)) #2 7-685-881-09 SCREW +BVTT 4X8 (S)
0 J905 1-835-507-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT DC10V 0.25A(LPS))

9
HS-AC1

4-2. AC BOARD SECTION

F902

F901
F904
F903

F900 not supplied

(SENSOR board)

#1
IC991

not supplied not supplied

D906

52

52

D900
51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 A-1560-451-A AC BOARD, COMPLETE 0 F902 1-576-332-33 FUSE, CYLINDRICAL (TIME LAG) (T10AL/250V)
52 3-905-609-01 SCREW (TRANSISTOR) 0 F903 1-532-505-33 FUSE (T5AL/250V)
0 D900 6-502-558-01 DIODE D20XBS6 0 F904 1-532-505-33 FUSE (T5AL/250V)
0 D906 6-502-558-01 DIODE D20XBS6 IC991 6-710-072-01 IC LM61CIZ/LFT2
0 F900 1-532-464-33 FUSE (T2.5AL/250V) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3

0 F901 1-576-332-33 FUSE, CYLINDRICAL (TIME LAG) (T10AL/250V)

10
 HS-AC1
SECTION 5
AC
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in • CAPACITORS
the parts list may be different from the uF: μF When indicating parts by reference num-
parts specified in the diagrams or the com- • COILS ber, please include the board.
ponents used on the set. uH: μH
The components identified by mark 0
• -XX and -X mean standardized parts, so • SEMICONDUCTORS
or dotted line with mark 0 are critical for
they may have some difference from the In each case, u: μ, for example:
safety.
original one. uA. . : μA. . , uPA. . , μPA. . ,
Replace only with part number specified.
• Items marked “*” are not stocked since uPB. . : μPB. . , uPC. . , μPC. . ,
they are seldom required for routine ser- uPD. . : μPD. .
vice. Some delay should be anticipated
when ordering these items.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-1560-451-A AC BOARD, COMPLETE < IC >
*******************
IC901 8-759-700-42 IC NJM2904D
1-533-313-11 HOLDER, FUSE
3-905-609-01 SCREW (TRANSISTOR) < IC LINK >
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
0 PS901 1-533-595-42 LINK, IC (3.15A/125V)
< CAPACITOR > 0 PS902 1-533-595-42 LINK, IC (3.15A/125V)
0 PS903 1-533-595-42 LINK, IC (3.15A/125V)
C901 1-164-159-11 CERAMIC 0.1uF 50V 0 PS904 1-533-595-42 LINK, IC (3.15A/125V)
0 C902 1-117-334-51 ELECT 3300uF 20% 25V 0 PS905 1-533-595-42 LINK, IC (3.15A/125V)
0 C904 1-119-939-51 ELECT 6800uF 20% 35V
0 C905 1-119-939-51 ELECT 6800uF 20% 35V 0 PS906 1-533-595-42 LINK, IC (3.15A/125V)
0 C906 1-119-939-51 ELECT 6800uF 20% 35V
< TRANSISTOR >
C911 1-164-159-11 CERAMIC 0.1uF 50V
C912 1-164-159-11 CERAMIC 0.1uF 50V Q901 8-729-620-05 TRANSISTOR 2SC2603-EF
Q902 8-729-021-73 TRANSISTOR 2SC2229-OY
< CONNECTOR > Q903 8-729-021-73 TRANSISTOR 2SC2229-OY
Q904 8-729-042-09 TRANSISTOR 2SA1038S-RSE-TP
CN900 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
* CN901 1-564-321-21 PIN, CONNECTOR (3.96mm PITCH) 2P < RESISTOR >
CN902 1-770-128-11 PIN, CONNECTOR (3.96mm PITCH) 2P
* CN903 1-564-506-11 PLUG, CONNECTOR 3P R901 1-247-871-11 CARBON 47K 5% 1/4W
CN904 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P R902 1-249-429-11 CARBON 10K 5% 1/4W
R907 1-247-831-11 CARBON 1K 5% 1/4W
* CN905 1-564-506-11 PLUG, CONNECTOR 3P R910 1-249-411-11 CARBON 330 5% 1/4W
* CN906 1-564-704-11 PIN, CONNECTOR (SMALL TYPE) 2P R911 1-247-831-11 CARBON 1K 5% 1/4W
CN907 1-784-922-11 PIN, CONNECTOR 5P
CN908 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P R912 1-247-831-11 CARBON 1K 5% 1/4W
CN909 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P R913 1-249-429-11 CARBON 10K 5% 1/4W
R914 1-249-411-11 CARBON 330 5% 1/4W
CN910 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P R915 1-247-847-11 CARBON 4.7K 5% 1/4W
R916 1-249-406-11 CARBON 120 5% 1/4W F
< DIODE >
R917 1-247-831-11 CARBON 1K 5% 1/4W
0 D900 6-502-558-01 DIODE D20XBS6 R918 1-249-429-11 CARBON 10K 5% 1/4W
0 D901 6-500-522-31 DIODE 10EDB40-TB5 R919 1-249-406-11 CARBON 120 5% 1/4W F
0 D902 6-500-522-31 DIODE 10EDB40-TB5 R920 1-247-903-00 CARBON 1M 5% 1/4W
0 D903 6-500-522-31 DIODE 10EDB40-TB5 R921 1-247-903-00 CARBON 1M 5% 1/4W
0 D904 6-500-522-31 DIODE 10EDB40-TB5
< RELAY >
0 D906 6-502-558-01 DIODE D20XBS6
D908 8-719-991-33 DIODE 1SS133T-77 0 RY901 1-755-266-11 RELAY, AC POWER
D909 8-719-991-33 DIODE 1SS133T-77
D910 8-719-991-33 DIODE 1SS133T-77 < CONNECTOR >
D911 8-719-991-33 DIODE 1SS133T-77
0 TB900 1-818-029-11 PIN, CONNECTOR 4P
D912 8-719-991-33 DIODE 1SS133T-77 (DC OUT DC 19.5V TOTAL4.5A)

< TERMINAL BOARD > < THERMISTOR (POSITIVE) >

ET901 1-537-771-21 TERMINAL BOARD, GROUND 0 TH900 1-803-638-11 THERMISTOR, POSITIVE (RUE400)
ET903 1-537-771-21 TERMINAL BOARD, GROUND *************************************************************

11
HS-AC1
SENSOR

Ref. No. Part No. Description Remark

SENSOR BOARD
*************

< DIODE >

D991 8-719-109-93 DIODE RD6.2ESB2

D992 8-719-991-33 DIODE 1SS133T-77

< IC >

0 IC991 6-710-072-01 IC LM61CIZ/LFT2

< RESISTOR >

R991 1-247-831-11 CARBON 1K 5% 1/4W

R993 1-249-439-11 CARBON 68K 5% 1/4W
R994 1-249-440-11 CARBON 82K 5% 1/4W
R995 1-249-429-11 CARBON 10K 5% 1/4W
R996 1-247-879-11 CARBON 100K 5% 1/4W

R997 1-247-878-00 CARBON 91K 5% 1/4W

R998 1-249-429-11 CARBON 10K 5% 1/4W
*************************************************************

MISCELLANEOUS
**************

5 1-817-961-11 CONNECTOR 4P (DC OUT DC 19.5V TOTAL4.5V)

0 F900 1-532-464-33 FUSE (T2.5AL/250V)
0 F901 1-576-332-33 FUSE, CYLINDRICAL (TIME LAG) (T10AL/250V)
0 F902 1-576-332-33 FUSE, CYLINDRICAL (TIME LAG) (T10AL/250V)
0 F903 1-532-505-33 FUSE (T5AL/250V)

0 F904 1-532-505-33 FUSE (T5AL/250V)

FAN901 1-787-331-11 FAN, D.C.
0 J904 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT 19.5V 2.5A(LPS))
0 J905 1-835-507-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT DC10V 0.25A(LPS))
0 J908 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT 19.5V 2.5A(LPS))

0 J909 1-835-508-11CORD, DC EXTERNAL POWER PLUG W

(DC OUT 19.5V 2.5A(LPS))
0 J910 1-835-508-11 CORD, DC EXTERNAL POWER PLUG W
(DC OUT 19.5V 2.5A(LPS))
0 T901 1-445-509-11 TRANSFORMER, POWER
*************************************************************

ACCESSORIES
************

0 1-782-783-22 CORD SET, POWER

4-113-753-11 MANUAL, INSTRUCTION (ENGLISH)

12
 HS-AC1

MEMO

13
HS-AC1

REVISION HISTORY

Checking the version allows you to jump to the revised page.

Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision
1.0 2009.02 New