WTX-14014549-75-ES-50

80 Watt, Ku-Band High Power Transmitter

Operation and Maintenance Manual
This page has been intentionally left blank.
Mitec Telecom inc.
Designers and manufacturers of telecom and wireless products

9000 Trans Canada,

Pointe-Claire, Quebec, Canada
H9R 5Z8

OPERATION AND MAINTENANCE MANUAL Preliminary Released

REVISION RECORD
Revision ECN # Description Date Approved

1 Engineering Release. 14 Mar 06

CM Approval TITLE:

WTX-14014549-75-ES-50 80 Watt,
14.0-14.5 GHz High Power
Transmitter Module

This document contains information proprietary to mitec telecom inc., or its affiliates, or to a third party to which mitec telecom inc. may have a legal obligation to protect
such information from unauthorized disclosure, use, or duplication. Any disclosure, use, or duplication of this document or of any of the information contained herein is
expressly prohibited except as mitec telecom inc. may otherwise agree in writing.

Designer: G. Cyr Date: 14 Mar 06

REV 1
DOCUMENT NO.
Technical Writer: C. Strunga Date: 14 Mar 06
211406MA PAGE 1 OF 37
mitec Preface

Preface
Scope

This document covers the installation, operation, and maintenance of the WTX-14014549-75-ES-
50 80 Watt, 14.0-14.5 GHz High Power Transmitter Module. It contains information intended for
engineers, technicians and operators working with the transmitter module.

To make inquiries, or to report errors of fact or omission in this document, please contact Mitec
Telecom inc. at (514) 694-9000.

IMPORTANT

Important information concerning the operation and care of this product, as well as safety of
authorized operators is highlighted throughout this document by one of the following labels:

NOTE
Indicates a reminder, a special consideration, or additional
information that is important to know.

CAUTION!
Identifies situations that have the potential to cause equipment
damage.

WARNING!!
Identifies hazardous situations that have the potential to cause
equipment damage as well as serious personal injury.

Rev 1 P-1
This page has been intentionally left blank.
This page has been intentionally left blank.
mitec Table of Contents

Table of Contents
1 INTRODUCTION ........................................................................... 1
1.1 Receiving and Inspection .........................................................................................2
1.1.1 Equipment Damage or Loss .............................................................................2
1.1.2 Return of Equipment ........................................................................................2

1.2 Preparing for Installation ........................................................................................3

1.3 Safety Precautions ....................................................................................................3

2 INSTALLATION & OVERVIEW .................................................. 5

2.1 General Description .................................................................................................5

2.2 Specifications ............................................................................................................5

2.3 General Considerations ...........................................................................................7

2.4 Basic Mechanical Characteristics ...........................................................................7

2.4.1 External View of the Transmitter Module........................................................7
2.4.2 Connections and Mounting Hardware..............................................................8

2.5 Assembly and Installation........................................................................................8

2.5.1 Lifting the Transmitter Module into Position and Temporary Attachment .....8
2.5.2 Securing the Transmitter Module.....................................................................8

2.6 Functional Overview ................................................................................................9

2.6.1 General .............................................................................................................9
2.6.2 IF/RF Conversion and Amplification.............................................................10
2.6.3 Monitor and Control .......................................................................................10
2.6.4 Internal Power Distribution Reference...........................................................11

3 OPERATION ............................................................................... 13
3.1 Procedure ................................................................................................................13
3.1.1 Interface ..........................................................................................................14

4 MAINTENANCE .......................................................................... 15

Rev 1 i
Table of Contents mitec

4.1 Preventive Maintenance.........................................................................................15

4.1.1 Procedure ........................................................................................................15
4.1.2 Transmitter Module Cooling System Preventive Maintenance......................15
4.1.3 Performance Check.........................................................................................16
4.1.4 Troubleshooting..............................................................................................16
4.1.5 Out-of Warranty Repair..................................................................................17

APPENDIX A ........................................................................................
Drawings & Schematic Diagrams ............................................................................ A-1

APPENDIX B ........................................................................................
Serial Protocol.............................................................................................................B-1

APPENDIX C ........................................................................................
Spare Parts ................................................................................................................. C-1

APPENDIX D ........................................................................................
Bench Test Record..................................................................................................... D-1

List of Tables
Table 1 –Specifications........................................................................................................5
Table 2 –Connector Pin Assignments................................................................................14
Table 3 - Recommended Corrective Actions.....................................................................16

List of Figures

Figure 1 – Recommended Distance for Mounting on the Hub............................................9

Figure 2 - System Block Diagram .....................................................................................10
Figure 3 – Outline Drawing ............................................................................................ A-3

ii Rev 1
mitec Introduction

1 Introduction
The WTX-14014549-75-ES-50 High Power Transmitter module is a highly reliable, high quality,
cost efficient 80W L-Band to Ku-Band High Power Up-Converter System designed for use in
VSAT applications. This line of superior products, engineered using state of the art technology,
is characterized by unparalleled durability and dependability. The system also has high linearity
over the full operating temperature range. The output operating frequency range is the standard
Ku-Band of 14.0 to 14.5 GHz.

Rev 1 Page 1
Introduction mitec

1.1 Receiving and Inspection

The transmitter module is designed to function outdoors and will arrive in a standard shipping
container. Immediately upon receipt of the transmitter module, check the Bill of Lading against
the actual equipment you have received. Inspect the shipping containers exteriors for visible
damage incurred during shipping.

CAUTION!
Handle the transmitter module with extreme care. Excessive shock
may damage transmitter module’s delicate internal components.

NOTE

Before unpacking the shipping containers, move them near to the

site where the system will be mounted. Ensure that the
containers are oriented correctly in accordance with the “This
Side UP ”labels. Carefully remove the transmitter module and
packing material from the shipping containers.

Using the supplied packing list, verify that all items have been received and undamaged during
shipment. Verify that all items are complete. If there are any omissions or evidence of improper
packaging, please notify Mitec Telecom inc. immediately.

1.1.1 Equipment Damage or Loss

Mitec Telecom Inc. is not responsible for damage or loss of equipment during transit. For
further information, contact the responsible transport carrier.

When declaring equipment as damaged during transit, preserve the original shipping cartons to
facilitate inspection reporting.

1.1.2 Return of Equipment

When returning equipment to Mitec for repair or replacement:

1. Identify, in writing, the condition of the equipment,

2. Refer to the sales order, Purchase Order and the date the equipment was received.

Notify Mitec Sales Administration Department of the equipment condition and obtain a Return
Material Authorization (RMA) number and shipping instructions. Mitec will pay for the cost of
shipping the product to the customer after the repairs are completed.

Page 2 Rev 1
 mitec Introduction

NOTE

Do not return any equipment without an RMA number. This is

important for prompt, efficient handling of the returned
equipment and of the associated complaint.

1.2 Preparing for Installation

Before attempting to install or use the transmitter module, we recommend that you first
familiarize yourself with the product by reading through this manual. Understanding the
operation of the system will reduce the possibility of incorrect installation, thereby causing
damage or injury to yourself or others.

The transmitter module must be installed in accordance with the

conditions and recommendations contained in the following
sections.
When you are ready to begin your installation, use the information in Chapter 2 (Installation) as a
guide for making all the required electrical connections.

1.3 Safety Precautions

Carelessness or mishandling of the transmitter module may damage the unit causing serious
injury to yourself or others. Please adhere to the following:

WARNING!!

This unit is equipped with an AC power cord and plug. Do not

tamper with, or attempt to reconfigure, the cord or plug supplied
with the unit, as this can:
♦ result in personal injury
♦ void the warranty
♦ cause damage to the units or related equipment.

Rev 1 Page 3
This page has been intentionally left blank.
 mitec Installation & Overview

2 Installation & Overview

2.1 General Description

This section describes the installation and theory of operation of the transmitter module.

The module is a stand-alone Transmitter System powered from 24 VDC and 190-260 VAC power
sources. It will amplify an input signal from an L-Band RF source up to a power level of 80
Watts CW in Ku-Band.

The Transmitter consists of a low power block up-converter (BUC) and a high power amplifier
(SSPA.)

The SSPA consists of a Power Supply, RF Amplifier, Control System and Cooling System. The
power supply provides DC voltages to the RF amplifier. The RF amplifier is capable of
providing an output level of 80W, and contains over temperature shut down and protection
circuits. The control system provides telemetry for the RF amplifier via an RS-485 serial
interface. The cooling system fan and heat sink fins together supply and distribute a steady flow
of air, preventing the internal electrical components of the SSPA from over-heating. All three
components are protected by a shroud, which can be removed easily when replacing the cooling
system fan. (Refer to Chapter 4). The SSPA is for outdoor use and is secured onto a mounting
frame by two brackets.

2.2 Specifications
Table 1 summarizes the specifications of the WTX-14014549-75-ES-50 80 Watt, 14.0-14.5 GHz
High Power Transmitter Module. For mechanical specifications, refer to the outline drawing,
Figure 3 in Appendix A.

Table 1 –Specifications

RF Performance
Output Frequency 14.0 to 14.5 GHz
IF Frequency 950 to 1450 MHz
LO Frequency 13.05 GHz
Reference Frequency 10 MHz External Reference;
(0 ± 5) dBm Input Power Level
Small Signal Gain 75 dB, min over temperature
Gain Flatness (small signal) ± 2.5 dB, nominal at 10 dB back-off
Gain Stability with power (expansion) 0.5 dB, max.
Output Power @ 250C 49 dBm (80 W), min at P1dB
Saturated Output Power 50 dBm, nominal
rd
3 Order Intermodulation each -26 dBc max., two equal signals at 43dBm/tone,
Rev 1 Page 5
Installation & Overview mitec

5 MHz separation
Phase Noise -60 dBc/Hz, max. @300 Hz offset of the carrier
-70 dBc/Hz, max. @ 1 kHz offset of the carrier
-80 dBc/Hz, max. @ 10 kHz offset of the carrier
-90 dBc/Hz, max. @ 100 kHz offset of the carrier
-100 dBc/Hz, max.@ 1 MHz offset of the carrier
Integrated Phase Noise Error 2.2 degrees, max., form 300 Hz to 1 MHz SSB
Source & Load VSWR 1.5:1 max (operational), infinite at any angle without
damage, unconditionally stable
Input Return Loss (cold) -14 typ.
Output Return Loss -18 dB
Spurious In-band -50 dBc, max @ P1dB
Spurious Out of Band -50 dBc, max @ P1dB
Harmonics N/A
RF Monitor Port (optional) POUT -45 dBc, typical
Power Consumption 1000 W typical
Controls
Gain N/A
Mute S/W Via RS-485
Mute H/W Short pin K with Pin M (M&C) connector
Over Temperature Shutdown (82 –2/+3)0 C. at case temperature, internally set
Indicators
RF Forward Power Via RS-485
RF Overdrive N/A
Over Temperature Via RS-485
Alarm Summary S/W Via RS-485
Alarm Summary H/W TTL Low - Alarm State
Contact closure (Pin E opens from Pin H on alarm)
Temperature Sensor Via RS-485
LED Green (operational) / Red (alarm)/Orange (muted)
Power Supply
Input 190-260 VAC, 50/60 Hz (1,000W)
Power Factor correction 95%
Output 12 VDC, 3.5 A
Efficiency 85% nominal
Design Technology High frequency switching modules
Mechanical Specifications
Package Outdoor, weather resistant
Size (overall dimensions 16.3”x 11.4”x 9.2”
Weight 54 lb (24.5 Kg)
Cooling Forced Air
Exterior Surface Finish Painted white
Hardware Stainless Steel
O-ring Silicone
Page 6 Rev 1
 mitec Installation & Overview

Connectors
IF Input N-type female
RF Output WR75 grooved
RF Monitor Type-N, female
AC Power MS3102R16-10P
RS-485 M&C MS3102R20-29S
Markings Labels permanent and legible
1 Mitec Name, Part No & Revision Level
2 Serial No.
3 IF Input
4 RF Output
5 AC power 220AC only
6 RS-485
7 RF Sample
Environmental Operational Storage
0 0
Temperature -40 to 60 C -500C to 850C
Humidity 5% to 95% at -400C 5% to 95% at 650C
Altitude 10,000 ft AMSL 40,000 ft AMSL
Shock and Vibration Normal transport and handling
Wind 100 km/hr N/A
Drop N/A 1m in shipping container
Reliability
MTBF (mean time between failures 80,000 hours (fan reliability data is not included.
Fan must be replaced once every 2 years minimum.

2.3 General Considerations

The module shall meet all specifications over full bandwidth and under all environmental
conditions when terminated with a load of VSWR at 1.5:1 unless otherwise specified. All RF
specifications shall be met within five minutes after applying DC power, except gain stability,
which shall be met after a warm-up period of twenty minutes. During the warm-up period, the
module shall not exhibit any alarm or require an RF mute input signal to reset any alarm/fault
latches.

2.4 Basic Mechanical Characteristics

2.4.1 External View of the Transmitter Module

The physical external dimensions of the transmitter module are shown in Figure 3 and Table 1.
All inputs and outputs are shown in Figure 3.

Rev 1 Page 7
 Installation & Overview mitec

2.4.2 Connections and Mounting Hardware

The IF input connection requires a coaxial cable with an N-type male connector for the RF Input.
The RF output requires a waveguide with a WR75 flat flange. An O-ring shall be used to seal the
waveguide connection. There are also two cylindrical connectors on the RF Input side of the RF
amplifier for AC power and M&C interface. The pin assignments for these connectors are shown
in section 3.1.3. Six screws (#1/4) and two brackets fasten the transmitter onto the mounting
frame. See Figure 3 in Appendix A. Four cap screws (#6-32) and their respective lock washers
fasten the antenna waveguide feeder on to the transmitter waveguide output flange. The mating
connectors, hardware and O-ring are in the shipping container with the transmitter.

2.5 Assembly and Installation

Use the information in this section as a guide to assemble and install the transmitter module. The
specified humidity is up to 100% during operation. However, installation should be carried out in
dry conditions, free of salt spray or excessive humidity. This will eliminate the possibility of
moisture and other foreign substances from entering the output waveguide flange.

CAUTION!

Only authorized technical personnel should perform the

Installation and proper electrical hookups of the transmitter
module.

2.5.1 Lifting the Transmitter Module into Position and Temporary Attachment
The transmitter module weighs approximately 25kg (55 lb), which should be handled by two
persons. Remove all plastic caps from the connectors and output waveguide flange. Lift the
transmitter module and install it on to the mounting frame opening. The transmitter module is
now ready for permanent attachment.

The transmitter is designed to operate in an outdoor environment and is waterproof when

mounted in the correct orientation as per Figure 1 and the orientation labels placed on the RF
amplifier shroud.

The transmitter contains a high flow-rate fan (600 CFM) for cooling the RF amplifier module.
This fan functions continuously during the transmitter operation. To provide a sufficient airflow,
the transmitter should be mounted with a minimum clearance of 5 inches on all four sides and
the bottom. Refer to Figure 1. Adequate cooling for the transmitter will provide years of top
performance.

2.5.2 Securing the Transmitter Module

Secure the transmitter module onto the mounting frame using the hardware described in section
2.3.2. Align the transmitter output waveguide flange with the mating flange of the antenna feeder
waveguide. Using the O-ring and hardware provided connect the antenna feeder waveguide.
Torque the flange screws to 16 inch-pounds (1.8 N-m). Attach the proper cables for waveguide
for IF input, AC power and M&C to the corresponding connectors of the transmitter module.
Refer to Figure 3 in Appendix A.
Page 8 Rev 1
 mitec Installation & Overview

NOTE

The cylindrical connectors are labeled clearly and have different

pin layouts. Refer to Figure 3. It is impossible to incorrectly
install the mating connectors.

5 5

Figure 1 – Recommended Distance for Mounting on the Hub

2.6 Functional Overview

2.6.1 General
This section describes the transmitter module functions in detail. The functional overview
explains the RF amplification, monitor & control and power distribution.

Figure 2 block diagram illustrates the transmitter module.

Rev 1 Page 9
 Installation & Overview mitec

RS-485
12V DC
Alarm

IF In
L-Band & BUC & RF Out
10MHz reference SSPA 49 dBm min @ P1dB
(0 +/- 5 dBm) 14.0-14.5 GHz
with 24VDC

12 VDC
80 A max

Cooling System Fan

Power Supply 600 CFM

AC Power IN
190-260 VAC
1,000 W

Figure 2 - System Block Diagram

2.6.2 IF/RF Conversion and Amplification

The IF Input signal with a 10MHz reference, 0-/+5dBm and 24VDC, 1.0A nominal enters the
BUC by a coaxial cable, converted to Ku-Band by the BUC and goes through an isolator, which
provides a good VSWR at the input. Under normal operation, the RF amplifier will amplify the
RF Input signal level up to a power level of 49 dBm (80 Watts CW) P1dB minimum. For small
signal gain, the transmitter module is capable of providing a gain of approximately 75 dB.

To achieve the rated output power, GaAs transistors, as well as other microwave components
within the RF Amplifier, provide the necessary gain and low insertion loss. The amplified signal
is transmitted through the output waveguide section to a satellite up-link system.

2.6.3 Monitor and Control

The transmitter has an RS-485 serial interface. The transmitter can communicate to the indoor
unit or redundancy control module via RS-485. (For RS-485 Protocol Specifications, see
Appendix B)

The control system can provide the following M&C functions:

System Alarm: when an amplifier is not functioning properly, TTL logic will activate an
alarm (TTL low: alarm state). The alarm signal will be transmitted via RS-485 as well as
through two analogue wires in order to support the redundancy option.
Mute Control (via RS-485)
Mute Control (via hardware line): Short pin K with Pin M (M&C connector)
Output Power Monitoring: 15 dB dynamic range (via RS-485)
Page 10 Rev 1
 mitec Installation & Overview

Base Plate Temperature Monitoring (via RS-485)

The SSPA can also provide 12VDC (3.5A max) at the same connector to supply DC power for
redundancy control.

2.6.4 Internal Power Distribution Reference

The SSPA operates from power source of 190 VAC to 260 VAC, 50 Hz to 60 Hz and will
consume 1,000-Watts maximum.

CAUTION!

There is an internal slow blowing fuse installed in the power

supply module in order to protect the entire system from over
current.

This unit is not intended to work with 110 volts. Do not attempt
to use at this voltage. Damage to the unit will occur.
The power supply converts the incoming AC voltage into two separate DC voltages. The DC
voltages are regulated to ensure isolation and stability. The module provides:

12 VDC, 80 A maximum to the RF amplifier circuits

Rev 1 Page 11
This page has been intentionally left blank.
 mitec Maintenance

3 Operation
This chapter describes the verification of the operation and control of the transmitter module. It
shall be performed by authorized personnel prior to maintenance and/or repair.

3.1 Procedure
Verify that the installation procedure described in Chapter 2 was completed. A complete physical
check of the customer’s system is suggested.

WARNING!

The output power available at the output waveguide flange is

extremely hazardous. Under no circumstances should be
transmitter be operated without the waveguide feed or a high
power load attached. Do not operate this equipment in the
presence of flammable gases or fumes. Failure to observe this
precaution will result in personal injury. Safe and careful
installation of this transmitter will eliminate the possibility of
accidents and provide years of top performance.
Verify the antenna feed waveguide connection is properly done before the transmitter is
energized.

NOTE

The transmitter module can withstand any source or load VSWR.

However, the transmitter module will meet all specification
requirements only if the source/load VSWR is sufficient (see
Section 7.1.20).

Normal operation is not possible if the antenna feeder VSWR is

greater than 1.5:1.
Turn ON the power and allow a warm up period of twenty minutes before operating the
transmitter module. This will assure stable gain and power. The transmitter module can function
with a coupler when a direct measurement of the output power is made.

Rev 1 Page 13
 Maintenance mitec

CAUTION!

It is strongly recommended not to exceed -20 dBm maximum RF

Input level. The RF amplifier will be in deep saturation if
overdriven. RF performance will degrade significantly, and proper
operation is not possible. This operational condition is the survival
mode for the transmitter module. Never exceed the maximum safe
RIF Input level of -10dBm (100 mW) or permanent damage to the
transmitter module may result.
Verify the status of the System Fail signal from the M&C interface using the RS-485 protocol.
(Protocol description is attached to this manual.)

3.1.1 Interface
The Mitec High Power Amplifier, WTX-14014549-75-ES-50 interface is shown in Table 2
below.
Table 2 –Connector Pin Assignments

Pin
Connector Name Type Signal Name Description Parameter
#
IF Input L-Band + 10 MHz
J1 “IF IN” N-type female N/A IF In
10 MHz Ref. In + DC
J2 “RF OUT” WR137 N/A RF Out RF Output 50 dBm, max
A L Line
190-260 VAC
J3 “AC Input” MS3102R16-10P B GND Ground
50 – 60 Hz
C N Neutral
A TX+(output to) RS-485 Interface
B TX- Half Duplex/
RS-485
C RX+(input from) Full Duplex
D RX- (Configurable)
E Reserved Reserved Reserved
F AL_Sum System_Alarm Alarm TTL Low
G GND Ground Signal GND
H Reserved Reserved Reserved
J GND Ground DC GND
To Mute short
MS3102R20- K M_I Mute In Pin K to Pin M
J4 “RS-485”
29S
+12 VDC 3.5A
L +12V +12 VDC Out
max
M M_I_Com Mute in Common
Summary Alarm Pin E opens from
N AL_Sum_NO
Normally Open Pin H on Alarm
Summary Alarm Pin E closes from
P AL_Sum_NC
Normally Closed Pin H on Alarm
R N/C N/C N/C
S N/C N/C N/C
T AL_Sum_Comm Alarm Common
J5 “RF Sample” SMA female N/A RF sample RF sample output POUT - 45dB, typ.

Page 14 Rev 1
 mitec Maintenance

4 Maintenance
This chapter contains information on how to maintain, troubleshoot and repair the transmitter
module. The transmitter module is extremely reliable, requiring very little preventive
maintenance, or repair. Should there be a malfunction, this chapter also contains technical
information to help diagnose basic failures.

4.1 Preventive Maintenance

4.1.1 Procedure

WARNING!

Shut down the transmitter module before disassembly and

remove all cables and connectors. Failure to observe this
precaution may result in personal injury or death. This includes
the removal of any RF power originating from other system
components.
When the transmitter module is in the hot stand-by mode in a redundant system, switch it to the
operation mode at least once every three months. Make sure the fan is running while in operation
mode.

When the transmitter module is in the cold stand-by mode in a redundant system, switch it to the
operation mode at least once every three months. Make sure the fan is running while in operation
mode.

4.1.2 Transmitter Module Cooling System Preventive Maintenance

Preventive maintenance is limited to checking the performance of the transmitter module cooling
system. No electrical or mechanical adjustments are required for normal operation.

The cooling system used a very high flow rate fan– 600CFM. Air is pulled from the front
side and is expelled on the RF OUT side. The high CFM may cause an excessive amount
dust and debris to collect at the intake openings (input side). Airflow openings must be
cleaned regularly.

The fan is the least reliable item in the transmitter module. Wearing of the fan bearings will
cause the RPM to drop and will create a higher than average heat-sink temperature. It is
recommended to replace the fan after 2 years of operation.

Rev 1 Page 15
 Maintenance mitec

4.1.3 Performance Check

Verify the system is properly set up as per Chapters 2 and 3. The power output at 1 dB
compression shall be measured for evaluating the performance of the transmitter module.

It is recommended to measure the following parameters for ensuring that the transmitter module
is in good working condition:
- Gain and Gain flatness
- RF load VSWR and RF source VSWR
- Two-Tone Intermodulation Distortion
- Return Loss at connectors J1 and J2 of the TRANSMITTER MODULE

Using a Source and an IF input signal level within the small signal region of the transmitter
module, measure the power level at connectors J1 and J2. See Table 2. Plot the swept response
on a test data sheet. From the plot, determine gain and gain flatness.

With an IF Input signal level within the small signal region of the transmitter module, measure
the VSWR (Return Loss) at connectors J1 and J2. See Table 2. Plot the swept return loss for
both the IF Input and RF Output signals on a test data sheet. From the plot determine the return
loss.

From the output power measurements determine P1dB. Record value on a test data sheet.

Measure the Two-tone Intermodulation Suppression using two equal signals separated by 5 MHz.
Record value on test data sheet.

4.1.4 Troubleshooting

WARNING!!

Cable connection and disconnection shall be done carefully to

avoid physical damage to the cables and connectors, which may
cause intermittent problems in the future.
Use Table 1 to quickly isolate a fault within the transmitter module. If the transmitter module is
defective, notify Mitec and follow the process detailed in section 1.1.2.

Symptom Action
Fails performance test Check power source, RF source, cabling and connectors.
Check for clogged fan and debris in heat-sink fins. Clean
thoroughly. If fan is worn, replace fan. If correct,
transmitter module is defective. Return transmitter module
to Mitec.
Table 3 - Recommended Corrective Actions

Page 16 Rev 1
 mitec Maintenance

4.1.5 Out-of Warranty Repair

A non-warranty and out-of-warranty repair service is available from Mitec for a nominal charge.
The customer is responsible for paying the cost of shipping the SSPA both to and from Mitec for
these repairs.

Rev 1 Page 17
This page has been intentionally left blank.
mitec Appendix A

Appendix A
Drawings & Schematic Diagrams
WTX-14014549-75-ES-50 Outline Drawing

Rev 1 A-1
This page has been intentionally left blank.
 mitec Appen

Figure 3 – Outline Drawing

Rev 1 A-3
This page has been intentionally left blank.
 mitec Appendix B

Appendix B
Serial Protocol
Appendix B contains the serial protocol documentation applicable to this product.

Rev 1 B-1
 9000 Trans Canada, Pointe Claire, QC, Canada H9R 5Z8
Confidential and Proprietary to Mitec. This is a Controlled Document.

Document Name: Protocol Specification Revision: 0E

File Name: PS-3900040-00-R0E.rtf Page: Page 1 of 14
Model Number: N/A Originator: R. Abdouche

Revision Date Change Summary Approval

0A 22-Apr-2003 Preliminary specification sent to customer. C. Villeneuve
0B Document does not exist.
0C Document does not exist.
0D 04-Dec-2003 Extracted protocol specs from technical specs document. C. Villeneuve
0E 16-Jan-04 Completely revamped the document format. No functional C. Villeneuve
changes made.

Serial Communication Protocol Specification

For
Control Software 3900040-00
 Table of Contents

1 Document legend_____________________________________________________________ 3
2 Project Overview _____________________________________________________________ 3
3 Definitions and acronyms______________________________________________________ 3
4 Scope ______________________________________________________________________ 3
5 Serial Communications Link Interface ___________________________________________ 4
5.1 Customer Interface Port Configuration _____________________________________________4
5.2 Customer Interface Cable Connections ______________________________________________4
6 Communication Protocol Framing ______________________________________________ 6
6.1 SCI Packet Frame Format ________________________________________________________6
6.1.1 SCI Packet Byte Description ___________________________________________________________ 6
6.1.2 Default Address Values _______________________________________________________________ 7
6.1.3 CRC Calculation Example_____________________________________________________________ 7
6.1.4 Command / Reply Packet Sequencing____________________________________________________ 7
7 Command List _______________________________________________________________ 8
7.1 Default Reply Packet Format ______________________________________________________8
7.2 GET Status Command List________________________________________________________9
7.3 GET Alarms Command List______________________________________________________11
7.4 SET Control Command List______________________________________________________12
8 Appendix I: Troubleshooting Guide_____________________________________________ 13

PS-3900040-00-R0E.rtf Rev. 0E
Designed: R. Abdouche Page 2 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM
1 Document legend

Text in this document highlighted in grey identifies features which are planned but not implemented yet.

2 Project Overview

This document describes the communications protocol used to communicate with high-power transmitter modules
(ODUs) configured with embedded software 3900040-00 when used in a stand-alone configuration.

Customer PC / Modem

Booster
(ex. Address = 0xF)
WTX Interface

Figure 1) System Block Diagram

If the Booster is configured in a redundant configuration or is connected through a transceiver, then the communications
protocol for the redundant kit or transceiver supercedes the present document.

3 Definitions and acronyms

The following terms appear throughout this document:

Controller: The microprocessor-based card and associated embedded software which

handles all communications between the customer interface and the
amplifier.
CRC: Cyclic Redundancy Check
Customer Interface Port: The interface port through which the device used by the customer will
interact with the Transceiver (ie. typically a modem or PC).
Customer Interface Device: The interface device used by the customer to interact with the Transceiver
(ie. typically a modem or PC).
PC: Personal Computer.
RF: Radio Frequency.
SCI: Serial Communications Interface.
WBT: Wavesat Bias Tee Unit
WTX: Wavesat Transmitter

4 Scope

This document covers all aspects of the communication protocol which are required for the customer to develop a
controlling device (typically a PC application program or modem) to interface with the Mitec product.

PS-3900040-00-R0E.rtf Rev. 0E
Designed: R. Abdouche Page 3 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM
5 Serial Communications Link Interface

5.1 Customer Interface Port Configuration

The customer interface port of the controller is configured as follows:

Baud Rate: 19200bps
Data bits: 8
Stop bits: 1
Parity: None
HW Control None

5.2 Customer Interface Cable Connections

This software protocol remains the same regardless of the transport medium used (ie RS232, RS485 half duplex
or RS485 full duplex). This section defines the wiring required to communicate with the Mitec product.

Note that the pin numbers on both side of the cable are deliberately omitted since these will vary depending on
the Mitec product as well as the PC / Modem interface. Please refer to the specific user manuals for pin
allocations.

Please refer to the user manual for the Mitec product if unsure of the customer interface transport medium.

For RS232:

TX RX

PC / Modem Transceiver
Interface RX TX Customer
Interface

Gnd Gnd

Note: Some PC com ports require that loopbacks be present at the PC / modem interface. If
such is the case, then connect the following signals together at the PC / modem interface:
Interconnect: "DTE Ready" to "DCE Ready" to "Received Line Signal Detect".
Also interconnect: "Request to Send" to "Clear to Send"

Also note that this diagram only represents the serial communication connections. Refer to
the user manual for any other signals which may be provided through this interface.

Figure 2) RS232 Customer Interface Wiring

PS-3900040-00-R0E.rtf Rev. 0E
Designed: R. Abdouche Page 4 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM
 For RS485 Half Duplex:

Data+ TX+

RX+
PC / Modem Transceiver
Interface Data- TX- Customer
Interface
RX-

Gnd Gnd

Note: Some PC cards provide TX+, RX+, TX- and RX- hardware signals
instead of Data+ and Data-. In this case, the TX+ and RX+ lines are to be
shorted together to form the Data+ signal. Similarly, the TX- and RX- lines
are to be shorted together to form the Data- signal.

Also note that this diagram only represents the serial communication
connections. Refer to the user manual for any other signals which may be
provided through this interface.

Figure 3) RS485 Half Duplex Customer Interface Wiring

For RS485 Full Duplex (ie RS422):

RX+ TX+

TX+ RX+
PC / Modem Transceiver
Interface RX- TX- Customer
Interface
TX- RX-

Gnd Gnd

Note that this diagram only represents the serial communication

connections. Refer to the user manual for any other signals which may be
provided through this interface.

Figure 4) RS485 Full Duplex (ie RS422) Customer Interface Wiring

PS-3900040-00-R0E.rtf Rev. 0E
Designed: R. Abdouche Page 5 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM
6 Communication Protocol Framing

6.1 SCI Packet Frame Format

The packets exchanged with the master controller will have the following format (regardless of direction):

Packet Frame Format:

MSB
LSB

Dest/Src
STX Cmd/Len Data CRC ETX
Address

MSB LSB

Data Format: Data1 Data2 Datan-1 Datan

Figure 5) SCI Packet Frame Format

6.1.1 SCI Packet Byte Description

♦ STX is the start transmission byte (defined as 0x7E). This byte is used to determine the start of a packet.

♦ Dest/Src Address contains the destination address in the high nibble and the source address in the low
nibble. The destination address is the address of the device which is to process the packet. The source
address is the address of the device which sent the packet. Note that the device address of the customer
interface device is always = 0x0F.

♦ CMD/Len contains the packet command in the high nibble and the number of bytes in the data portion of
the packet in the lower nibble.

The following commands may be sent by the customer interface device:

GET (command high nibble = 0x0) Request the current value of a database element.
SET (command high nibble = 0x1) Set the database element to the specified value.

The following commands may be returned to the customer interface device:

UPD (command high nibble = 0x8) Return the current value of a database element.
ACK (command high nibble = 0xE) Acknowledge a received packet.
NACK (command high nibble = 0xF) Reject a received packet (Not ACKnowledge).

♦ Data1 - Datan contains the packet payload. The value of the data bytes is specific to the command and will be
covered in following sections.

♦ CRC is the cyclic redundancy check and is calculated by performing a byte-wise exclusive OR of the
Dest/Src address byte, Cmd/Len byte and all data bytes. A bit-wise inversion is then applied to the CRC
before being inserted into the packet.

♦ ETX is the end transmission byte (defined as 0x7F). This byte is used to determine the end of a packet.

PS-3900040-00-R0E.rtf Rev. 0E
Designed: R. Abdouche Page 6 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM
6.1.2 Default Address Values

The customer interface device must always be assigned address 0xF.

The Transceiver device address is factory defaulted to 0xF. It may be set by the customer using the SET Transceiver
Address command (refer to SET Control Command List).

The Booster device address is factory defaulted to 0xE. It may be set by the customer using the SET Booster Address
command (refer to SET Control Command List).

6.1.3 CRC Calculation Example

To send a command to read the temperature (database element =

0x0606) from the Booster (device address 0x0F), the command is:

7E FF 02 06 06 02 7F

Dest/Src = 0xFF 1111 1111

XOR
CMD/Len = 0x02 0000 0010

= 1111 1101
XOR
Data1 = 0x06 0000 0110
= 1111 1011
XOR
Data2 = 0x06 0000 0110
= 1111 1101

Perform bitwise
= 0000 0010 = 0x02 CRC
inversion of final result:

6.1.4 Command / Reply Packet Sequencing

The Transceiver will never send a packet to the customer interface device unless a command is received. In other words,
the Transceiver will not speak unless spoken to.

PS-3900040-00-R0E.rtf Rev. 0E
Designed: R. Abdouche Page 7 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM
7 Command List

7.1 Default Reply Packet Format

This section identifies the packet format the ACK (Acknowledge) and NACK (Not acknowledge) replies which may be sent to the customer interface device in
response to a received command.

NOTE: The packets shown in the list below are based on the assumption that the Booster device address is set to 0xF. To modify the commands for different
addresses, the Dest/Src byte and the CRC byte will have to change in all packets.

Reply Packet Format Explanation Interpretation Examples

ACK (Acknowledge) 7E FX E0 ZZ 7F Acknowledge that the received packet was X = Device address of the packet 1) reply: 7E FF E0 E0 7F
properly processed. source device. (ACK reply sent from the Booster)
ZZ = CRC.
NACK (Not Acknowledge) 7E FX F1 YY ZZ 7F Indicate that a problem was encountered with X = Device address of the packet 1) reply: 7E FF F1 03 F2 7F
the received packet. source device. (NACK reply sent from the Booster for an
invalid CRC)
YY = Error code
(03 = Incorrect CRC 2) reply: 7E FF F1 18 E9 7F
18 = Unrecognized command (NACK reply sent from the Booster for an
30 = Set command attempted on a unrecognized command).
restricted database element)

ZZ = CRC.

PS-3900040-00-R0E.rtf Rev. 0E_

Designed: R. Abdouche Page 8 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM _
7.2 GET Status Command List

This section identifies the list of commands available to query any unit for status information.

NOTE: The packets shown in the list below are based on the assumption that the Booster device address is set to 0xF. To modify the commands for different
addresses, the Dest/Src byte and the CRC byte will have to change in all packets.

Command Packet Format Explanation Possible Replies Interpretation Examples

Get Booster Temperature 7E FF 02 06 06 02 7F Query booster for Update Booster Temp: TT TT = Booster temp in oC + 273. 1) cmd: 7E FF 02 06 06 02 7F
current temperature ZZ = CRC. reply: 7E FF 84 06 06 01 02 87 7F
7E FF 84 06 06 TT TT ZZ 7F (Temp = 0x0102 = 0d258 – 273 =
-15oC)

2) cmd: 7E FF 02 06 06 02 7F
NACK Refer to 7.1. reply: 7E FF 84 06 06 01 34 B1 7F
(Temp = 0x0134 = 0d308 – 273 =
+35oC)
Get Booster Temperature 7E FF 02 2F FF D2 7F Query booster for Update Booster Temp VV VV = Booster temp sensor 1) cmd: 7E FF 02 2F FF D2 7F
Sensor Voltage current temperature Sensor: voltage from 0V (0x0000) to +5V reply: 7E FF 84 2F FF 02 06 50 7F
sensor voltage (Note: (0x03FF). (Voltage = 0x0206 = 0d518.
This command is to be 7E FF 84 2F FF VV VV ZZ 7F Temp = (518 x 0.4883) – 273 =
used if a more accurate The conversion formula is: -20.1oC)
temperature reading is Temp = (Voltage x 0.4883) – 273.
required than the result 2) cmd: 7E FF 02 2F FF D2 7F
of the “Get Booster ZZ = CRC. reply: 7E FF 84 2F FF 02 76 20 7F
Temperature” (Voltage = 0x0276 = 0d630.
command.) Temp = (630 x 0.4883) – 273 =
+34.6oC)
NACK Refer to 7.1.
Get Booster Output Power 7E FF 02 17 FF EA 7F Query booster for Update Booster Output PP PP = Output power in 10 x 1) cmd: 7E FF 02 17 FF EA 7F
current output power Power: dBm. reply: 7E FF 84 17 FF 01 2C 41 7F
ZZ = CRC. (Power = 0x012C = 0d300 =
7E FF 84 17 FF PP PP ZZ 7F 30.0dBm.)

2) cmd: 7E FF 02 17 FF EA 7F
reply: 7E FF 84 17 FF 01 A0 CD 7F
NACK Refer to 7.1. (Power = 0x01A0 = 0d416 =
41.6dBm.)
Get Booster Gain (if 7E FF 02 18 FF E5 7F Query booster for Update Booster Gain: GG GG = Gain in 10 x dB. 1) cmd: 7E FF 02 18 FF E5 7F
applicable) current gain ZZ = CRC. reply: 7E FF 84 18 FF 02 08 69 7F
7E FF 84 18 FF GG GG ZZ 7F (Gain = 0x0208 = 0d520 = 52.0dB.)

2) cmd: 7E FF 02 18 FF E5 7F
reply: 7E FF 84 18 FF 01 95 F7 7F
NACK Refer to 7.1. (Gain = 0x0195 = 0d405 = 40.5dB.)

PS-3900040-00-R0E.rtf Rev. 0E_

Designed: R. Abdouche Page 9 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM _
 Command Packet Format Explanation Possible Replies Interpretation Examples
Get Mute Status 7E FF 02 06 01 05 7F Query booster for Update Mute Status: MM = Mute status (0 = enabled; 1 1) cmd: 7E FF 02 06 01 05 7F
mute status = muted) reply: 7E FF 84 06 01 00 00 83 7F
7E FF 84 06 01 00 MM ZZ 7F ZZ = CRC. (Booster is enabled.)

2) cmd: 7E FF 02 06 01 05 7F
reply: 7E FF 84 06 01 00 01 82 7F
(Booster is muted.)
NACK Refer to 7.1.
Get IF Frequency 7E FF 02 16 FF EB 7F Query transceiver for Update IF Frequency: XX XX = System IF frequency in 1) cmd: 7E FF 02 16 FF EB 7F
IF frequency MHz. reply: 7E FF 84 16 FF 03 B6 D8 7F
7E FF 84 16 FF XX XX ZZ 7F ZZ = CRC. (IF frequency set to 0x03B6 = 0d950
NACK Refer to 7.1. = 950 MHz)
Get Booster SW Version 7E FF 02 05 FC FB 7F Query booster for SW Update SW Version Base SW version base number MSB is 1) cmd: 7E FF 02 05 FC FB 7F
Base number (MSB) version base MSB MSB: always 0x3900. reply: 7E FF 84 05 FC 39 00 44 7F

7E FF 84 05 FC 39 00 44 7F cmd: 7E FF 02 05 FD FA 7F
NACK Refer to 7.1. reply: 7E FF 84 05 FD 00 40 3C 7F
Get Booster SW Version 7E FF 02 05 FD FA 7F Query booster for SW Update SW Version Base XX XX = SW version base number
cmd: 7E FF 02 05 FE F9 7F
Base number (LSB) version base LSB LSB: (LSB).
reply: 7E FF 84 05 FE 00 00 7F 7F
ZZ = CRC.
7E FF 84 05 FD XX XX ZZ 7F
cmd: 7E FF 02 05 FF F8 7F
NACK Refer to 7.1. reply: 7E FF 84 05 FF 30 41 0F 7F
Get Booster SW Version 7E FF 02 05 FE F9 7F Query booster for SW Update SW Version Config: XX = SW version configuration.
Configuration version configuration ZZ = CRC. The resulting software version is:
7E FF 84 05 FE 00 XX ZZ 7F 3900040-00-R0A
NACK Refer to 7.1.
Get Booster SW Version 7E FF 02 05 FF F8 7F Query booster for SW Update SW Version revision: RR RR = SW version revision
Revision version revision represented as two ASCII
7E FF 84 05 FF RR RR ZZ 7F characters.
ZZ = CRC.
NACK Refer to 7.1.
Get Booster Device Address 7E FF 02 03 04 05 7F Query booster for Update booster device XX = Booster device address. 1) cmd: 7E FF 02 03 04 05 7F
device address address: ZZ = CRC. reply: 7E FF 84 03 04 00 0A 89 7F
(Booster device address = 0xA)
7E FF 84 03 04 00 XX ZZ 7F
NACK Refer to 7.1. 2) cmd: 7E FF 02 03 04 05 7F
reply: 7E FF 84 03 04 00 0E 8D 7F
(Booster device address = 0xE)

PS-3900040-00-R0E.rtf Rev. 0E_

Designed: R. Abdouche Page 10 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM _
7.3 GET Alarms Command List

This section identifies the list of commands available to query any unit for alarm information.

NOTE: The packets shown in the list below are based on the assumption that the Booster device address is set to 0xF. To modify the commands for different
addresses, the Dest/Src byte and the CRC byte will have to change in all packets.

Command Packet Format Explanation Possible Replies Interpretation Examples

Get Booster Over 7E FF 02 00 02 00 7F Query booster for over Update booster over XX = Alarm state (0 = no alarm; 1 1) cmd: 7E FF 02 00 02 00 7F
Temperature Alarm temperature alarm temperature alarm: = alarm) reply: 7E FF 84 00 02 00 01 87 7F
ZZ = CRC. (Booster over temp alarm is raised)
7E FF 84 00 02 00 XX ZZ 7F
NACK Refer to 7.1. 2) cmd: 7E FF 02 00 02 00 7F
reply: 7E FF 84 00 02 00 00 86 7F
(Booster over temp alarm is clear)
Get Booster Low Power 7E FF 02 00 05 07 7F Query booster for low Update booster low power XX = Alarm state (0 = no alarm; 1 1) cmd: 7E FF 02 00 05 07 7F
Alarm (if applicable) power alarm alarm: = alarm) reply: 7E FF 84 00 05 00 01 80 7F
ZZ = CRC. (Booster low power alarm is raised)
7E FF 84 00 05 00 XX ZZ 7F
NACK Refer to 7.1. 2) cmd: 7E FF 02 00 05 07 7F
reply: 7E FF 84 00 05 00 00 81 7F
(Booster low power alarm is clear)
Get Booster Summary 7E FF 02 00 0F 0D 7F Query booster for Update booster summary XX = Alarm state (0 = no alarm; 1 1) cmd: 7E FF 02 00 0F 0D 7F
Alarm summary alarm alarm: = alarm) reply: 7E FF 84 00 0F 00 01 8A 7F
ZZ = CRC. (Booster summary alarm is raised)
7E FF 84 00 0F 00 XX ZZ 7F
NACK Refer to 7.1. 2) cmd: 7E FF 02 00 0F 0D 7F
reply: 7E FF 84 00 0F 00 00 8B 7F
(Booster summary alarm is clear)

PS-3900040-00-R0E.rtf Rev. 0E_

Designed: R. Abdouche Page 11 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM _
7.4 SET Control Command List

This section identifies the list of commands available to set control parameters any unit.

NOTE: The packets shown in the list below are based on the assumption that the Booster device address is set to 0xF. To modify the commands for different
addresses, the Dest/Src byte and the CRC byte will have to change in all packets.

Command Packet Format Explanation Possible Interpretation Examples

Replies
Set Mute Control 7E FF 14 13 01 00 MM ZZ 7F Mute / Unmute the up link. ACK Refer to 7.1. 1) cmd: 7E FF 14 13 01 00 01 07 7F
reply: ACK
MM = Mute control (1 = (Mute up link)
Mute; 0 = enable) Refer to 7.1.
NACK
2) cmd: 7E FF 14 13 01 00 00 06 7F
ZZ = CRC reply: ACK
(Enable up link)
Set IF Frequency 7E FF 14 16 FF XX XX ZZ 7F Set up link frequency ACK Refer to 7.1. 1) cmd: 7E FF 14 16 FF 03 B6 48 7F
reply: ACK
XX XX = Frequency in MHz. (Set IF frequency to 950 MHz = 0x3B6)

ZZ = CRC 2) cmd: 7E FF 14 16 FF 04 33 CA 7F
reply: ACK
(Set IF frequency to 1075 MHz = 0x433)

3) cmd: 7E FF 14 16 FF 04 B0 49 7F
NACK Refer to 7.1. reply: ACK
(Set IF frequency to 1200 MHz = 0x4B0)

4) cmd: 7E FF 14 16 FF 05 2D D5 7F
reply: ACK
(Set IF frequency to 1325 MHz = 0x52D)

5) cmd: 7E FF 14 16 FF 05 AA 52 7F
reply: ACK
(Set IF frequency to 1450 MHz = 0x5AA)
Set Booster Device Address 7E FF 14 03 04 00 XX ZZ 7F Set booster device address ACK Refer to 7.1. 1) cmd: 7E FF 14 03 04 00 0A 19 7F
(0 ≤ address ≤ 0xE) reply: ACK
(Set Booster device address to 0xA)
NACK Refer to 7.1. 2) cmd: 7E FF 14 03 04 00 0E 1D 7F
reply: ACK
(Set Booster device address to 0xE)

PS-3900040-00-R0E.rtf Rev. 0E_

Designed: R. Abdouche Page 12 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM _
8 Appendix I: Troubleshooting Guide

Problem Possible Remedies

No response at all from Booster 1) Ensure the cable assembly is wired properly (refer to 5.2Customer Interface Cable
Connections) and that it is properly connected between the transceiver customer interface
port and the customer device.

2) Verify that the com port parameters are as specified in 5.1Customer Interface Port
Configuration.

3) Confirm that the customer interface cable is connected to the correct PC com port.

4) Ensure that there are no other applications executing on the same com port.

5) If the transport medium is RS232, then connect the loopbacks identified in the note in Figure
2) RS232 Customer Interface Wiring.

6) If using a Booster address other than 0xF, then send a “GET Booster Device Address”
command to destination address 0xF. The reply will contain the current booster address. Note
that the booster will respond to all commands received with destination address 0xF.

7) If the transport medium is RS485 half duplex, note that some PC cards require software
control of the RS485 transmit and receive buffer enable lines. The software in the customer
device may need to coordinate the enabling /disabling of these buffers.

8) Ensure the booster is powered on.

Reply packet is incomplete. 1) If software control of the transmit and receive buffer enable lines is required (RS485 half
duplex), then it is possible that the timing between the transition needs to be adjusted.

PS-3900040-00-R0E.rtf Rev. 0E_

Designed: R. Abdouche Page 13 of 14
Approved: C. Villeneuve 31-01-05 9:51 AM _
 mitec Appendix C

Appendix C
Spare Parts
Appendix C contains a table of recommended spare parts for on-hand replacement. The
following sheet can be copied and used as a fax form to order the required spare parts. Please
make sure to include all identifying information to facilitate the processing of your order. The
order may also be sent via email or regular mail delivery, at the following address.

Mitec Telecom inc.

9000 Trans Canada Hwy.
Pointe Claire, Québec, Canada
H9R 5Z8

Fax: (514)694-3814
Email: [email protected]

For additional information, please contact our customer service department at:
(514) 694-9000 or 1-800-724-3911

Rev 1 C-1
This page has been intentionally left blank.
 mitec Appendix C

mitec telecom inc.

designers and manufacturers of telecom & wireless products
ISO 9001 Certified

WTX-14014549-75-ES-50
Spare Parts Order Form 80 Watt, 14.0-14.5 GHz High
Power Transmitter Module
From:

Place By: Signature:

Telephone:
Fax Email:

Part Description Part Number Quantity Unit Line

Price* Total*

* To be completed by Mitec Sales Department

Fax to: Customer Service (514) 694-3814

Rev 1 C-3
This page has been intentionally left blank.
mitec Appendix D

Appendix D
Bench Test Record
Appendix D contains the Bench Test Record used to record test data for this product.

Rev 1 D-1
 mitec telecom inc.
9000 Trans Canada, Pointe-Claire, Quebec, Canada H9R 5Z8
Document: BR-WTX-14014549-75-ES-50-R01.doc Date: March 7, 2006
Number: WTX-14014549-75-ES-50 Page: 1 of 3
Rev: 01 Originator: G.C.
Title: L- to Ku-Band 80W 75 dB Gain ODU Approval: M.L.

Revision Date Change Summary Approval

0A March 7, 2006 Initial Release ML
01 April 5, 2006 ECN 143-06S ML

Serial Number: _______________ Tested by: _______________ Date: _______________

Input Frequency
Spec Parameters
F1=950MHz F2=1050MHz F3=1150MHz F4=1250MHz F5=1350MHz F6=1450MHz
Output Frequency, (GHz)
1 14.0 14.1 14.2 14.3 14.4 14.5
14.0-14.5GHz
-40°CAMB
Gain, (dB)
2 +25°CAMB
75 dB typ
+55°CAMB

Gain flatness, (dB) -40°CAMB

3 ±2.5dB nom +25°CAMB
+55°CAMB
49.0dBm, typ.
-40°CAMB
Output Power P1dB, 49.0dBm, min.
4
(dBm) +25°CAMB
49.0dBm, typ.
+55°CAMB
IMD, (dBc) FC = 14.00 GHz FC = 14.25 GHz FC = 14.50 GHz
5 -26dBc max. separated 5Mhz, 2 tones,
43dBm/tone, +25°CAMB
Spurious in Band, (dBc)
6
-50dBc max, POUT=P1dB, -40°CAMB
Spurious out of Band, (dBc)
7
-50dBc max, POUT=P1dB, -40°CAMB
Phase Noise, (dBc/Hz)
FC=14.25GHz, offset from FC
-60dBc/Hz @ 300Hz dBc/Hz @ 300Hz
-70dBc/Hz @ 1KHz dBc/Hz @ 1KHz
8 -80dBc/Hz @ 10KHz dBc/Hz @ 10KHz
-90dBc/Hz @ 100KHz dBc/Hz @ 100KHz
-100dBc/Hz @ 1MHz dBc/Hz @ 1MHz
2.2 degrees max degrees max from 300Hz up to 1MHz
from 300Hz up to 1MHz
TAMBIENT
Temperature Shut +60°C min.
9
Down, (°C) THOT SPOT
+85°C max.
RF Monitor Port, (dBc) FC = 14.00 GHz FC = 14.25 GHz FC = 14.50 GHz
10
-45dBc typ.
11 Output RL -18dB min.
mitec telecom inc.
9000 Trans Canada, Pointe-Claire, Quebec, Canada H9R 5Z8
Document: BR-WTX-14014549-75-ES-50-R01.doc Revision: 01 Page: 2 of 3

Monitor and Control Interface Test.

1. Mute Control H/W Contact Closure Passed/Failed

2. Mute Control S/W via RS-485 Passed/Failed

3. Temperature monitor via RS-485 Passed/Failed

4. Output Power Detector via RS-485 Passed/Failed

5. System Alarm H/W Relay Contact Closure Passed/Failed

6. System Alarm H/W TTL alarm Passed/Failed

7. System Alarm S/W via RS-485 Passed/Failed

8. Redundant voltage 12 Volts between L & J Passed/Failed

9. LED Green (Normal op.) Passed/Failed

Red (alarm) Passed/Failed
Orange (muted) Passed/Failed

10. Output Power Detector (See attached tables)

Plots And Graphs To Be Attached:

-Test Spec 2 - Gain vs Frequency (TAMB: -40°C, +25°C, +55°C) ___p.

-Test Spec 4 - Pin vs Pout (FC: F1, F3, F6 and TAMB: -40°C, +25°C, +55°C) ___p.
-Test Spec 5 (optional) - IMD (TAMB = +25°C) ___p.
mitec telecom inc.
9000 Trans Canada, Pointe-Claire, Quebec, Canada H9R 5Z8
Document: BR-WTX-14014549-75-ES-50-R01.doc Revision: 01 Page: 3 of 3

Interfaces

Pin
Connector Name Type Signal Name Description Parameter
#
IF Input L-Band + 10
J1 “IF IN” N-type female N/A IF In
10 MHz Ref. In MHz + DC
J2 “RF OUT” WR137 N/A RF Out RF Output 50 dBm, max
A L Line
190-260 VAC
J3 “AC Input” MS3102R16-10P B GND Ground
50 – 60 Hz
C N Neutral
A TX+(output to) RS-485
B TX- Interface
C RX+(input from) RS-485 Half Duplex/
Full Duplex
D RX-
(Configurable)
E Reserved Reserved Reserved
F AL_Sum System_Alarm Alarm TTL Low
G GND Ground Signal GND
H Reserved Reserved Reserved
J GND Ground DC GND
To Mute short Pin
K M_I Mute In
K to Pin M
J4 “RS-485” MS3102R20-29S +12 VDC 3.5A
L +12V +12 VDC Out
max
Mute in
M M_I_Com
Common
Pin E opens
Summary Alarm
N AL_Sum_NO from Pin H on
Normally Open
Alarm
Summary Alarm Pin E closes
P AL_Sum_NC Normally from Pin H on
Closed Alarm
R N/C N/C N/C
S N/C N/C N/C
T AL_Sum_Comm Alarm Common
RF sample
J5 “RF Sample” SMA female N/A RF sample POUT - 45dB, typ.
output
 Power detector table
Pout (dBm) 14.00 GHz 14.25 GHz 14.50 GHz
49
47
42
35
29