Caterpillar Cat 226B3 SKID STEER LOADER (Prefix AS2) Service Repair Manual (AS200001 and Up)

Service Repair Manual
Model
226B3 SKID STEER LOADER

226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S... 1/17
Shutdown SIS
Previous Screen
Product: SKID STEER LOADER

Model: 226B3 SKID STEER LOADER AS2
Configuration: 226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly

259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i02358306
Piston Pump (Hydrostatic) - Disassemble

SMCS - 5070-015-H7
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7289 Ruler 1
B 1P-1861 Retaining Ring Pliers 1
C 138-7576 Link Brackets 2
D 8T-4956 Bolts (M12 - 1.75 - 35 MM) 2
E 8T-4223 Hard Washers (13.5 - 25.5 - 3 MM THK) 2
F 1P-0510 Driver Gp 1
G 1P-1854 Retaining Ring Pliers 1
H 1U-7600 Slide Hammer Puller Gp 1
J 1P-1860 Retaining Ring Pliers 1
K 8H-0663 Bearing Puller Gp 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Remove".
Note: The following procedure is intended for cleaning purposes only.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/10/13
Illustration 1 g00903455
1. Remove the fittings and connectors (1).
2. Remove speed sensing valve (2).
Personal injury can result from being struck by parts propelled by a

released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to

release the spring force.
3. Remove cover (3) and the spring for the crossover relief valve.
4. Remove seat (4).
5. Note the orientation of spring (5).
6. Remove O-ring seal (6) from cover (3).
7. Remove back up ring (7) from cover (3).
8. Repeat Step 3 through Step 7 for the other covers.


9. Remove plug (8) for the charge relief valve.
10. Remove seat (9).
11. Remove shims (12).
12. Remove spring (13).
13. Remove seal (11) from plug (8).
14. Remove O-ring seal (10) from plug (8).
15. Use Tooling (A) to measure the distance from the stud to the nut. Record the distance for
assembly purposes.
16. Remove screws (14).
17. Remove nut (15).
18. Remove cover (16).
19. Remove O-ring seal (17) from cover (16).
20. Use Tooling (B) to remove retaining ring (18). Remove actuator assembly (19).
21. Remove O-ring seal (20) from actuator assembly (19).


Note: Keepers (21) must be marked for assembly. Do not mix keepers (21). The keepers are
not interchangeable.
22. Place actuator assembly (19) in a suitable press.
23. Remove keepers (21).
24. Remove shaft (26).
25. Remove spring retainer (22).
26. Remove spring (23).
27. Remove spring retainer (24).
28. Remove spacer (25).
29. Repeat Step 15 through Step 28 for the other cover.
30. Remove caps (27).
31. Remove connectors (28).
32. Remove fitting (29).
33. Remove adapter (30).
Note: Mark the location of the notch in stud (31) by making a corresponding mark on the
housing for installation purposes.
34. Use Tooling (A) to measure the distance from stud (31) to nut (32). Record the distance for
assembly purposes.
35. Remove stud (31) and nut (32).
36. Repeat Step 34 and Step 35 for the other stud.
37. Remove connector (33).
38. Remove caps (34).
39. Remove fittings (35).
40. Use Tooling (A) to measure the distance from studs (36) to nuts (37). Record the distance
for assembly purposes.
41. Remove studs (36) and nuts (37).
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine... 10/17
42. Remove bolts (38) from cover (39).
43. Use a suitable lifting device, Tooling (C), Tooling (D), and Tooling (E) to raise the piston
pump housing.
Note: Mark the port plates for assembly. Port plates are not interchangeable.
44. Remove port plate (40).
45. Remove plug (41) and the O-ring seal.
46. Remove slotted pin (42).
47. Repeat Step 45 and Step 46 for the other side.
48. Remove the rotating assembly and swashplate (43).
49. Remove linkage (44).
50. Remove bearing assemblies (45) and (46).
51. Remove swashplate (47).
Note: Mark the reaction plate assembly and the barrel.
52. Remove reaction plate assembly (48) from barrel (49).
53. Remove the retainer and shims (51) from barrel (50).


54. Place barrel (50) in a suitable press.
55. Use Tooling (F) and Tooling (G) to remove retaining ring (52) and spring (55).
56. Remove washer (54).
57. Remove pins (53).
58. Remove bearing races (56) from pins (57).
59. Remove O-ring seal (58).
60. Inspect dowel (59) for damage.
61. Use Tooling (B) to remove retaining ring (60).
62. Use Tooling (H) to remove seal (61).
63. Use Tooling (B) to remove retaining ring (62).
64. Remove shaft (63).
65. Use Tooling (J) to remove retaining ring (64).
66. Use a suitable press and Tooling (K) to remove bearing (65).
67. Remove bearing (66).
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
68. Remove actuator (67).
69. Remove seal (68).
70. Remove liner (69).
71. Repeat Step 42 through Step 70 for the other end of the piston pump.
Copyright 1993 - 2019 Caterpillar Inc. Sun Oct 13 08:45:38 UTC+0800 2019
All Rights Reserved.
Private Network For SIS Licensees.
Shutdown SIS
Previous Screen
Product: SKID STEER LOADER

Model: 226B3 SKID STEER LOADER AS2
Configuration: 226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly

259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i02362815
Piston Pump (Hydrostatic) - Assemble

SMCS - 5070-016-H7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7289 Ruler 1
B 1P-1861 Retaining Ring Pliers 1
F 1P-0510 Driver Gp 1
G 1P-1854 Retaining Ring Pliers 1
J 1P-1860 Retaining Ring Pliers 1
K 8H-0663 Bearing Puller Gp 1
L 2P-8301 Seal Guide 1
M 6V-2055 Grease 1
N 1U-6395 Grease 1
P 9S-3263 Thread Lock Compound 1
1. Install liner (69).
2. Install seal (68).
3. Install actuator (67).
4. Install bearing (66).
5. Raise the temperature of bearing (65).
6. Use a suitable press and Tooling (K) to install bearing (65).
7. Use Tooling (J) to install retaining ring (64).
8. Install shaft (63).
9. Use Tooling (B) to install retaining ring (62).
10. Dowel (59) must be aligned with the piston pump housing during assembly.
11. Install O-ring seal (58).
12. Install bearing races (56) on pins (57).

Caterpillar Cat 226B3 SKID STEER LOADER (Prefix AS2) Service Repair Manual (AS200001 and Up)

Uploaded by

Copyright:

Available Formats

Caterpillar Cat 226B3 SKID STEER LOADER (Prefix AS2) Service Repair Manual (AS200001 and Up)

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Caterpillar Cat 226B3 SKID STEER LOADER (Prefix AS2) Service Repair Manual (AS200001 and Up)

Uploaded by

Copyright:

Available Formats

Service Repair Manual

226B3 SKID STEER LOADER

Product: SKID STEER LOADER

Disassembly and Assembly

Piston Pump (Hydrostatic) - Disassemble

Note: The following procedure is intended for cleaning purposes only.

1. Remove the fittings and connectors (1).

2. Remove speed sensing valve (2).

Personal injury can result from being struck by parts propelled by a

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended tooling to

4. Remove seat (4).

5. Note the orientation of spring (5).

6. Remove O-ring seal (6) from cover (3).

7. Remove back up ring (7) from cover (3).

8. Repeat Step 3 through Step 7 for the other covers.

Personal injury can result from being struck by parts propelled by a

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended tooling to

9. Remove plug (8) for the charge relief valve.

10. Remove seat (9).

11. Remove shims (12).

12. Remove spring (13).

13. Remove seal (11) from plug (8).

14. Remove O-ring seal (10) from plug (8).

16. Remove screws (14).

17. Remove nut (15).

18. Remove cover (16).

19. Remove O-ring seal (17) from cover (16).

21. Remove O-ring seal (20) from actuator assembly (19).

Personal injury can result from being struck by parts propelled by a

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended tooling to

22. Place actuator assembly (19) in a suitable press.

23. Remove keepers (21).

24. Remove shaft (26).

25. Remove spring retainer (22).

26. Remove spring (23).

27. Remove spring retainer (24).

28. Remove spacer (25).

29. Repeat Step 15 through Step 28 for the other cover.

30. Remove caps (27).

31. Remove connectors (28).

32. Remove fitting (29).

33. Remove adapter (30).

35. Remove stud (31) and nut (32).

36. Repeat Step 34 and Step 35 for the other stud.

37. Remove connector (33).

38. Remove caps (34).

39. Remove fittings (35).

41. Remove studs (36) and nuts (37).

42. Remove bolts (38) from cover (39).

44. Remove port plate (40).

45. Remove plug (41) and the O-ring seal.

46. Remove slotted pin (42).

47. Repeat Step 45 and Step 46 for the other side.

48. Remove the rotating assembly and swashplate (43).

49. Remove linkage (44).

50. Remove bearing assemblies (45) and (46).