Network Video Recorders Quick Guide-V1.01 - 788729 - 168459 - 0

Network Video Recorders
Quick Guide
Version: V1.01
BOM: 3101C0FC
Thank you for purchasing our product. Contact your local dealer if you have any
questions or feedback. No part of this manual may be copied, reproduced,
translated, or distributed in any form or by any means without prior consent in
writing from our company. Contents of this manual are subject to change without
prior notice. No statement, information, or recommendation in this manual shall
constitute formal guarantee of any kind, expressed or implied.
Safety Information
Read through the instructions carefully before starting installation and operation.
 Installation and maintenance must be performed by qualified personnel.
 This device is a class A product and may cause radio interference. Take measures if
necessary.
 Disconnect power before installation and cable connection. Wear antistatic gloves
during installation. Use the manufacturer recommended battery. Improper use or

replacement of the battery may cause risk of explosion. Dispose of the used
battery according to local regulations or the battery manufacturer's instructions.
Never dispose of the battery in fire.
 The device is intended for indoor use only. Ensure a proper operating environment,
including temperature, humidity, ventilation, power supply, and lightning

protection. The device must always be properly grounded. Keep the device from
dust, excessive vibration, liquid of any kind, and strong electromagnetic radiation.
A sudden power failure may cause device damage or loss of data.
 Take necessary measures to ensure data security and protect from network attack
and hacking (when connected to Internet).

Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
1
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
 This device may not cause harmful interference.
 This device must accept any interference received, including interference that may
cause undesired operation.

LVD/EMC Directive
This product complies with the European Low Voltage Directive
2014/35/EU and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical
& Electronic Equipment (WEEE) Directive and must be disposed of in
a responsible manner.
Default IP, Username and Password

 Default IP address: 192.168.1.30 or 192.168.0.30 (vary with firmware version)
 Default admin username: admin
 Default admin password: 123456 (only for first login and should be changed to a
strong one with at least 8 characters including upper and lower case letters, digits
and symbols to enhance account security.)
2
Disk Installation
Choose an option. Use a 1# or 2# screwdriver as needed. All photos are only for
illustration.
Option 1 (for 1 or 2 disks)

1. Remove the cover, connect data 2. Connect data and power cables to the
and power cables to disk(s), and motherboard and then install the
then secure disk(s) with screws. cover.
Option 2 (for more than 2 disks)

You will open the cover and install hard disks on mounting plate(s).
1. Remove the cover and then 2. Connect data and power cables to
secure disks to mounting disks. Secure mounting plate(s) to the
plate(s) with screws. device, and then install the cover.
3
Option 3 (for more than 2 disks)
You will open the front panel and install hard disks on mounting brackets.
1. Secure the disk to a pair of 2. Press the latches on both sides (1) and
用双手分别按住前面板两侧卡扣，
mounting brackets (L means then detach the front panel (2).
按方向②拆卸前面板
用螺钉将硬盘固定在拉手条上，拉
left and R means right).
手条注意区分左右
3. Align the disk at the slot and 4. Push the disk slowly until it clicks.
then insert the disk gently. Repeat the steps to install all disks and
用拇指推进硬盘，可听到扣上的声音，
对准硬盘槽位，轻缓、平稳地插入
硬盘
then close the front panel.
完成该硬盘安装
Ports, Interfaces and LEDs

The ports, interfaces, connectors, power on/off switch and LED indicators may vary
with device model. See the following two examples.
4
Audio output
PoE ports Grounding
Power on/off
USB
HDMI output
DC power VGA output
Network
Audio input
eSATA interface RS232 (for maintenance)

CVBS output Alarm input/output
AC power
Network
Power on/off
Grounding 12V DC output
Audio out/input RS485
HDMI output USB

VGA output HDMI output
5
LED Description
PWR(Power) Steady on: Connected to power.
 Steady on: Normal.
RUN(Operation)
 Blinks: Starting up.
NET(Network) Steady on: Connected to network.
GUARD(Arming) Steady on: Arming is enabled.
 Steady on: Activated for remote control.
IR
 Blinks: Authenticating device code.
ALM(Alarm) Steady on: Device alarm occurred.
CLOUD Steady on: Connected to cloud.
One HD LED only:
 Steady on: No disk; or disk is abnormal.
 Blinks: Reading or writing data.
One HD LED for each disk:

HD(Hard disk)
 Steady green: Normal.
 Blinks green: Reading or writing data.
 Steady red: Abnormal.
 Blinks red: Rebuilding array.
Startup
Verify installation and cable connection are correct. Connect to power and then turn
on the power on/off switch (if applicable). Follow the wizard to complete the basic
setup after the NVR starts up.
6
Live View
Click Menu > Camera > Camera. The discovered cameras are listed. Click to add
a camera. To search a network segment, click Search. If a camera is added but live
video is not available, check network connection and make sure the correct camera
username and password are set in the system. Modify if necessary.
Playback
Right-click a preview window and then choose Playback to view video recorded on
the current day. A 7×24 recording schedule is enabled at delivery and can be edited
under Menu > Storage > Recording.
Access Using a Web Browser

Access the NVR using a Web browser (e.g., Internet Explorer) from a connected
computer.
1. Enter the NVR's IP address in the address bar and then press Enter. Install the
plugin as prompted. Close all Web browsers when the installation starts.
2. Open the Web browser and log in with the correct username and password.
Shutdown
Use the Shutdown menu instead of by disconnecting power or turning off the
power on/off switch. A sudden power failure may cause device damage and loss of
data.

Network Video Recorders Quick Guide-V1.01 - 788729 - 168459 - 0

Uploaded by

Copyright:

Available Formats

Network Video Recorders Quick Guide-V1.01 - 788729 - 168459 - 0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Network Video Recorders Quick Guide-V1.01 - 788729 - 168459 - 0

Uploaded by

Copyright:

Available Formats

Network Video Recorders

during installation. Use the manufacturer recommended battery. Improper use or

including temperature, humidity, ventilation, power supply, and lightning

and hacking (when connected to Internet).

cause undesired operation.

Default IP, Username and Password

Option 1 (for 1 or 2 disks)

Option 2 (for more than 2 disks)

Ports, Interfaces and LEDs

eSATA interface RS232 (for maintenance)

Grounding 12V DC output

Audio out/input RS485

HDMI output USB

 Blinks: Reading or writing data.

One HD LED for each disk:

 Blinks green: Reading or writing data.

 Steady red: Abnormal.

 Blinks red: Rebuilding array.

Access Using a Web Browser

You might also like