I.

Features and Application

H series right angle gearbox can transmit the prime mover horizontal axis power to the vertical pump axis,

which is economical, efficient, space-saving and suitable for various climatic conditions.

H series right angle gearbox is directly matched with diesel engine, horizontal motor or steam turbine, which

can be used for transmission and speed change of various vertical pumps such as long-axis pump, deep well pump,

diagonal flow pump, axial flow pump and submerged pump as well as the right angle transmission and speed

change of various vertical axis machines. The H-series right angle gearbox can directly support the axial forces

that may exist in the machine and simplify the structure of the machine. Can be widely used in farmland irrigation,

water conservancy engineering, municipal engineering, metallurgical mine, petrochemical engineering, fire

control and marine engineering, etc.

A variety of models and transmission ratios can meet the requirements of high and low speed prime movers

and pumps.

II. Speed Grading

Table 1

Horizontal axis speed (r/min)

Vertical axis speed
Speed increase ratio ——Active: slave
(r/min)
1:2 4:7 2:3 3:4 4:5 5:6 10:11 1:1

490 245 280 327 368 392 408 445 490

580 290 331 387 435 464 483 527 580

690 345 394 460 518 552 575 627 690

720 360 411 480 540 576 600 655 720

860 430 491 573 645 688 717 782 860

960 480 549 640 720 768 800 873 960

1160 580 663 773 870 928 967 1055 1160

1460 730 843 973 1095 1168 1217 1327 1460

1760 880 1006 1173 1320 1408 1467 1600 1760

3460* 1730 1977 2307 2595 2768 2883 3145 3460

1
 Horizontal axis speed (r/min)
Vertical axis speed
Speed decrease ratio -- Active: slave
(r/min)
11:10 6:5 5:4 4:3 3:2 7:4 2:1 9:4 5:2 3:1 4:1

490 539 588 613 653 735 858 980 1103 1225 1470 1960

580 638 696 725 733 870 1015 1160 1305 1450 1740 2320

690 759 828 863 920 1035 1208 1380 1553 1725 2070 —

720 792 864 900 960 1080 1260 1440 1620 1800 2160 —

860 946 1032 1075 1147 1290 1505 1720 1935 2150 2580 —

960 1056 1152 1200 1280 1440 1680 1920 2160 2400 2880 —

1160 1276 1392 1450 1547 1740 2030 2320 2610 2900 3480 —

1460 1606 1752 1825 1947 2190 2555 2920 3285 3650 — —

1760 1936 2112 2200 2347 2640 3080 3520 — — — —

* Please consult our company

III.Selection of Parameter
When it is used to drive deep well pumps, the parameters in Table 2 already contain suitable load factors,

which can be directly selected by the user. For other situations, please consult our company.

The American Gear Manufacturing Association stipulates that the spiral bevel gear load factor shall be

greater than or equal to 1.5, and the load factor values shall be different for different applications. In addition,

other factors affecting the rated power of the gearbox include bearing, axis, temperature and lubrication, which

have been taken into account in Table 2.

The selection of oil cooling method should take factors such as thrust, speed, ventilation environment and

operating conditions into account. For a gearbox equipped with an oil cooler, it shall be operated with a coolant of

about 20 ℃.

IV. Selection of Thrust Bearing Form

The upper part of the vertical axis (hollow axis) is made of bearings that can withstand large thrusts, which

can meet the requirements of most pumps and different heads. In most cases, the thrust of the gearbox itself is

mainly used to reduce the load that the pump acts on the "thrust bearing" of the vertical axis, so there is a

minimum downward thrust to prevent the vertical axis "thrust bearing" from separating.

2
 Unless otherwise noted, H-series gearbox is generally arranged in the DT format shown in the figure,

corresponding to the "standard" thrust shown in Table 2.

If there is insufficient "upward thrust" or "downward thrust", it can be arranged in the DF format shown in

the figure, corresponding to the "two-way" thrust shown in Table 2.

If the "downward thrust" exceeds the standard thrust value shown in Table 2, it can be selected by heavy type,

corresponding to the DT/DT arrangement format shown in the figure.

The heavy type can also be arranged according to the DF/DT format shown in the figure. At this time, the

downward thrust corresponds to the "standard, thrust value" in Table 2, and the upward thrust is selected

according to "two-way" in Table 2.

Table 2 Thrust value

Vertical axis Standard Heavy type Two-way

Power
Model speed Single downward thrust (N) Maximum downward or
HP/kW
(r/min) Minimum Maximum Minimum Maximum upward thrust(N)

860 46/34 9120 32900 43200 19600

960 50/37 8980 31540 42100 19100

H80 1160 58/43 8680 30700 6675 40500 18250

1460 69/51 8000 28500 36900 16910

1760 80/60 7560 26700 35600 13350

860 63/46 10450 32900 43200 19600

960 69/51 9920 31540 42100 19100

H110 1160 80/60 9790 30700 8000 40500 18250

1460 95/70 9120 28500 37800 16910

1760 110/81 8450 26700 35600 13350

720 63/46 12900 37800 12460 54300 22700

860 72/53 12000 35600 11800 51600 21400

960 79/58 11780 34790 11560 50400 21000

H125
1160 90/66 11350 33400 11100 48000 20000

1460 108/79 10680 31150 10200 44900 18700

1760 125/92 9790 28900 9800 42300 17400

3
 Standard Heavy type Two-way
Vertical
Power Maximum downward
Model axis speed Single downward thrust (N)
HP/kW or upward thrust
(r/min)
Minimum Maximum Minimum Maximum (N)

720 75/55 13570 43600 14000 66750 26250

860 87/64 13130 41830 13350 63630 24900

960 95/70 12890 40120 13000 62120 24100

H150
1160 108/79 12240 39160 12460 59180 23600

1460 129/95 11570 36930 11570 55620 22250

1760 150/110 11120 35600 11120 53400 21360

720 100/73.5 16000 53400 15130 72085 30000

860 116/85 14680 48950 14240 68080 28000

960 126/93 14100 47680 13920 65610 27000

H200
1160 144/106 13570 45400 13350 63630 25360

1460 172/126.5 12680 42270 12680 60000 23580

1760 200/147 12000 40000 12000 57850 22690

720 150/110 16700 60700 16700 83660 36500

860 174/128 15800 57850 16000 79650 34700

960 189/139 15500 56100 15600 77210 33200

H300
1160 216/159 14900 54300 14900 74310 32500

1460 258/190 14000 51200 14000 69860 30700

1760 300/220 13350 48950 13350 66750 29400

720 175/129 18900 72530 18700 89000 43600

860 203/149 18000 68970 17800 84500 41400

960 221/162 17700 67300 17400 82400 40300

H350
1160 252/185 16700 64100 16700 79200 38300

1460 301/221 15800 60500 15600 74300 36500

1760 350/257 15130 57850 15100 71200 34700

4
 720 213/156.5 20700 83200 21100 111200 49840

860 246/181 19800 79650 20200 106800 47610

960 268/197 19100 77230 19700 103700 46510

H425
1160 306/225 18500 73870 18700 97900 44500

1460 366/269 17350 69860 17800 93400 41830

1760 425/312 16900 66750 16900 89000 40050

720 250/184 23360 83200 23360 111200 49840

860 290/213 22250 79650 22470 106800 47610

960 315/232 21870 77160 21670 103700 46510

H500
1160 360/265 20700 73870 20470 97900 44500

1460 430/316 19580 69860 19580 93400 41830

1760 500/367.5 18690 66750 18690 89000 40050

720 300/220 24500 89000 24250 115700 53400

860 348/256 23140 84500 23360 111200 50730

960 378/278 22670 82400 22770 107100 49720

H600
1160 432/317 21800 79200 21580 102300 47610

1460 516/379 20500 74300 20470 97900 44500

1760 600/441 19580 71200 19580 93400 42720

720 375/276 27600 89000 27800 115700 53400

860 435/320 26250 84500 26700 111200 50730

960 473/347 25300 82800 26000 107100 49720

H750
1160 540/397 24500 79200 24500 102300 47610

1460 645/474 23140 74300 23580 97900 44500

1760 750/551 22250 71200 22250 93400 42720

490 279/205 34500 108000 37500 125000 60000

580 329/242 32000 102000 34200 120000 57800

H1000 720 408/300 30700 97000 30900 115700 53400

860 488/359 29340 93400 29700 111200 50730

960 544/400 28500 91700 29200 107100 49720

5
 1160 660/485 27600 87300 28500 102300 47610

1460 830/610 26250 84500 27200 97900 44500

1760 1000/735 24000 79100 25000 93400 42720

490 680/500 35000 108000 38600 125000 60000

580 821/604 32600 102000 35400 120000 57800

720 1020/750 31200 97000 31800 115700 53400

H1360 860 1217/895 29800 93400 30600 111200 50730

960 1360/1000 29700 91700 30200 107100 49720

1160 1643/1208 28200 87300 29500 102300 47610

1460 2067/1520 26900 84500 28300 97900 44500

Table 2A Power and Bearing Thrust Values at Different Speeds

Vertical axis

speed 490 580 690 720 860 960 1160 1460 1760 2000 2200 2400* 2800* 3000*

(r/min)

% of power

at 30 43 48 50 58 63 72 86 100 105 111 116 128 133

1760r/min

% of thrust

at 150 144 136 134 126 122 115 106 100 96 92 90 85 83

1760r/min

Note: 1. Parameters in Table 2 are only for FIG. 1 indicates the direction of rotation, please consult our

company for other directions of rotation;

2. If the vertical axis speed exceeds 2200r/min, please contact our company.

6
V. Dimensions (According to NEMA Standards)

Rigid coupling (anti-reverse wheel)

Hollow axis drive

Keyway "Y"

4-BY threaded
hole

Keyway "X"

4 - BF hole
1/2 "pipe joint
(at normal temperature,
clean fresh water)

Table 3 Dimensions (mm)

Keyway Max.BX
Model CD D U XA N AG H BE BD AJ AK BB BF XD
"X" FIG.1,4 FIG.2,3

H80 514 228.5 48 419 90 629 102 19 419 375 343 5 18 14X4.5X70 40 None 45

H110 635 289 50 445 90 749 102 25 419 375 343 5 18 14X4.5X70 50 50 54

H125 635 289 50 445 90 749 102 25 419 375 343 5 18 14X4.5X70 50 50 54

H150 762 336.5 60 521 120 876 102 25 508 375 343 5 18 18X5.5X95 55 55 60

H200 762 336 62 521 120 876 102 25 508 440 380 5 18 18X7X95 50 50 60

H300 762 336.5 70 610 140 1016 133 29 508 375 343 5 18 20X6X121 60 60 66

H350 978 419 70 737 140 1168 178 32 622 559* 343 10 24 20X6X121 60 60 76

H425 1080 419 75 762 145 1168 159 32 622 559* 343 10 24 20X6X121 60 60 85

H500 1080 419 90 787 170 1168 159 32 622 559* 343 10 24 25X7X140 75 75 85

H600 1080 419 95 838 190 1295 203 32 622 559* 343 10 24 25X7X140 75 80 100

H750 1162 482.5 100 914 190 1372 197 38 775 660 559 10 24 28X8X152 90 90 100

H1000 1405 545 110 1043 210 1610 153 35 920 860 600 7 8-28 28X8X170 100

H1360 1507 550 130 1290 250 1725 153 35 1250 1180 1120 -5 8-28 32X9X220 110

7
 Note: ① Dimensions of CD and H may change when the heavy type thrust drive is used; Dimensions of

XA, U, N and X may change when the speed decrease ratio is 7:4-4:1, please contact our company.

② Dimensions of D, CD, AG, XA, U, N and X may change when the speed increase ratio is 3:4-1:2,

please contact our company.

③ 4 cases, namely the direction of rotation shown in FIG.2-FIG.4, heavy type thrust, speed decrease

ratio of 7:4~3:1, and the speed increase ratio of 3:4-1:2, it is produced according to the special

order.

④ Tolerance: Axis diameter U, base groove AK, coupling hole BX

⑤ * 4 pieces of M16 screw holes (depth: 25) can also be arranged on the circumference of a circle

with the diameter of Φ375.

VI. Ordering Instructions

When ordering the H-Series gearbox, please provide the following data:

Model:__________.

Transmission ratio (see Table 1): __________, speed of pump ___________r/min, speed of prime

mover :_________r/min.

Direction of rotation:__________ .

Maximum downward thrust _____________, upward thrust:__________(Minimum downward thrust is shown in

Table 2).

Pump axle power: _____________. Pump axle diameter (BX):_____________.

Operation mode: Continuous:_____________ Interrupted_____________.

8
VII. Transportation Weight and Size
Packing container dimension
Net Gross weight --Kg
-- (mm) Volume
Model weight
Plywood m3
kg Domestic Container Length Width Height
box

H80 130 140 145 155 635 485 940 0.29

H110 175 186 195 200 635 485 940 0.29

H125 180 190 198 205 635 485 940 0.29

H150 290 310 320 330 840 585 1120 0.55

H200 290 310 320 330 840 585 1120 0.55

H300 410 455 455 480 1020 765 1295 1.1

H350 630 680 680 705 1170 765 1320 1.2

H425 720 770 770 795 1170 765 1320 1.2

H500 730 780 780 805 1170 765 1320 1.2

H600 930 1010 —— 1050 1270 790 1500 1.5

H750 1370 1480 —— 1540 1450 965 1550 2.2

H1000 2200 2480 —— 1560 2050 1100 1800 4.1

H1360 2800 3000 —— 3080 2200 1450 1950 6.2

Note: Actual weight and size may vary slightly

Table 3A: Standard drive part connection dimension

Bolt Keyway Y (width
Hole BX Thread BY Depth XL
circumference BZ x depth)

φ25 φ46 4-M6 9 8x3.3

φ30 φ60 4-M8 9 8x3.3

φ35 φ60 4-M8 11 10 x 3.3

φ40 φ70 4-M8 13 12x 3.3

φ45 φ70 4-M8 15 14x3.8

φ50 φ80 (H125) 4-M10 15 14x3.8

φ50 φ90 4-M10 15 14x3.8

φ55 φ90 4-M10 17 16x4.3

φ60 φ100 4-M10 19 18x4.4

(φ65) (φ100 ) 4-M10 19 18x4.4

φ70 φ140 4-M10 21 20 x 4.9

(φ75) (φ140 ) 4-M10 21 20 x 4.9

φ80 φ140 4-M10 23 22 x 5.4

φ90 φ150 4-M10 26 25 x 5.4

φ100 φ160 4-M10 29 28 x 6.4

φ110 φ160 4-M12 29 28 x 6.4