TM

Limited Lifetime Faucet Warranty

fluid™ warrants its faucets to be free from defects in material and workmanship for as long
as the original consumer purchaser owns his or her home.* This warranty applies only in original
installation location. If a defect is found in normal residential use, fluid™ will, at its election,
repair, provide a replacement part or product, or make an appropriate adjustment. fluid™
reserves the right to examine the product in question and its installation prior to replacement.
This warranty is limited to replacement of defective parts only. Damage to a product caused
by misuse, abuse, neglect, accident, improper installation, improper care of finishes, hard water
or mineral deposits, potassium or salt based water softener systems or exposure to corrosive
materials are not covered by this warranty. Improper care and cleaning will void the warranty.**
Replacement parts can be obtained from your local dealer or directly from the fluid™ warehouse.
Shipping charges may apply. Dated proof of purchase must accompany all warranty claims. This
warranty applies only to fluid ™ faucets installed in the United States of America, Canada or
Mexico (North America). fluid™ recommends using a certified plumber for faucet installation
and repair. Incidental and consequential damages, labor charges, repair or replacement costs
are expressly excluded. In no event shall the liability of fluid™ exceed the purchase price of the
faucet. Some states and provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This warranty gives you
specific legal rights which vary from state/province to state/province. If you find any such
problem with your product, please immediately contact your nearest fluid™ dealer or sales
representative.

Need Help? Installation Instructions for

For additional assistance
Toll Free: 1 800 460 7019
Fax: 1 604 430 5050 Pull Down Kitchen Faucet
www.fluidfaucets.com

* Two year warranty on commercial applications.

** Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents
or other products not recommended for surface finishes. This will void the warranty.

This faucet meets or exceeds the following standards:

ASME A112.18.1 / CSA B125.1 / NSF61-9
AB1953 California Lead Plumbing Law Certified
This product has been tested and certified by IAPMO.
Pull Down Kitchen Faucet/2017 / V3

Sustainable Solutions International

Phone: 1 800 460 7019
IAPMO LISTED www.SustainableSolutions.com Please Keep This Manual For Future Reference
Tools Required for Installation Installation Instructions
Allen Wrench (supplied) Teflon Tape 1. Shut off cold and hot water supplies. threaded tube (#10), from top insert plastic
2. On mounting surface the faucet hole turning tool (#9) into threaded tube (#10) and
Turning Tool (supplied) Adjustable Wrench should be 1-1/2” (38 mm) in diameter. turn clock-wise to fasten faucet body (#1).
The center of hole should be at least 7. To limit the spout (#21) turning angle to 140
3-1/16” (78mm) away from the back wall. degrees, insert rotation stop (#28) with arrow
3. For installation of faucet directly onto pointing to front onto threaded tube (#10).
mounting surface, ensure O-ring (#11) is 8. From above feed spray hose (#22) through
in place under faucet body (#1). For spout (#21) and threaded tube (#10), then fit
installation with escutcheon (#12) or spout (#21) onto threaded tube (#10) so that
deck plate (#26), remove O-ring (#11) it snaps into place.
before fitting escutcheon (#12) or deck 9. From below slide spring (#27) onto spray
140 Deg Rotation Stop
plate (#26) under faucet body (#1). hose (#22).
4. Place faucet body (#1) on the mounting 10. With washer (#18) in place, screw quick
surface by feeding braided flex hoses connector (#16) onto spray hose (#22) and
(#17) and quick connector sleeve (#15) tighten with an adjustable wrench.
through faucet hole.
5. From below, fit spacer (#13) and mount- 11. After pushing quick connector sleeve (#15) up
-ing plate (#14) onto threaded tube (10). to OPEN position, insert quick connector (#16)
into sleeve (#15). Pull sleeve (#15) down to
Note: If spacer (#13) is omitted, mount-
LOCK position to secure quick connector (#16).
-ing deck thickness can be increased by
5/8” (16mm) to a total of 2-1/8” (54mm). 12. With seal washer (#23) in place, screw spray
head (#24) onto spray hose (#22).
6. After mounting plate (#14) is attached to
Spray Pattern: Turn on faucet and water will always come from the
Optional 8” Deck Plate
Not Included
areator. Push diverter button (#25) to switch to spray.
Care & Maintenance Instructions
fluid ™ products are designed and engineered under strict quality standards. Regular and proper
care of our products will ensure years of trouble-free service.
For Cartridge: For Spray Aerator:
1. Shut off cold and hot water supplies. Regularly remove with the supplied turning tool (#9)
2. Use Allen wrench (#8) to push silicon and wash aerator of sprayhead (#24) with clean running
plug (#7) into handle hub and loosen set water and ensure any trapped debris has been removed.
screw (#6) but do not remove it. For Flow Restrictor and Back Flow Preventor:
3. Pull off handle (#5), unscrew cap (#4) Remove quick connector (#16) from spray hose (#22)
Flow Direction

and remove retaining nut (#3) using an and insert the supplied Allen wrench (#8) into smaller
adjustable wrench. end of connector (#16) to push both flow restrictor
4. Pull off cartridge (#2) by hand. (#19) and back flow preventor (#20) out. Rinse with
5. Wash cartridge (#2) with clean running clean running water and ensure that any trapped debris
water and ensure that any trapped debris has been removed. Replace, paying careful attention
Specifications:
has been removed. Dry and lightly grease to the correct flow direction as shown. If inserted
Max flow 1.5 gpm or 5.7 L/min
Flow pressure 15-72.5 psi at 60 psi all rubber seals (use only NSF approved incorrectly your faucet will not function properly.
Max pressure 120 psi Silicone grease). For Surface Finish:
Max temperature 176 F or 80 C
Max deck thickness 2-1/8”(54mm) 6. Replace cartridge (#2), retaining nut Clean with a damp cloth and warm soapy water. Then
Inlet connection 3/8”comp (#3) and cap (#4) followed by handle (#5), simply rinse off and wipe dry with a soft cloth. Do not
Spout rotation 140 or 360 degree then retighten set screw (#6). use abrasive or harsh cleaners as they may result in
finish damage.